
User Manual
20cm between the radiating element of this device and the user. This device must
AAX74688001
1page
1. Installation to Product
This product is only used inside LED lighting luminaire of LG Electronics
This device is for LG Electronics lighting products only.
FCC approval
The satisfy FCC exterior labeling requirements, the following text must be placed on
the exterior of the end product.
Contains Transmitter module FCC ID : BEJAAX74688001
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This device should be installed and operated with minimum distance
not be co-located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators and following statements shall be
included to host user manual
1) The antenna must be installed such that 20cm is maintained between the antenna
and users.
2) This module may not be co-located with any other transmitters or antennas.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements with this module installed. In the event that
these conditions cannot be met, then the FCC authorizations are no longer
considered valid and the FCC ID cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end
product including this module and obtaining separate FCC authorizations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

User Manual
B digital device, pursuant to part 15 of the FCC Rules. These limits are
that to which the receiver is connected
Operation is subject to the following
This equipment has been tested and found to comply with the limits for a Class
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
- Consult the dealer or an experienced radio/ TV technician for help.
AAX74688001
.
2page
IC approval
The host device must be labeled to display the Industry Canada certification
.
Contains transmitter module IC: 2703H-AAX74688001
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de
certification d'Industrie Canada du module.
Contient module émetteur IC : 2703H-AAX74688001
This device complies with Industry Canada license-exempt RSS standard(s).
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard
RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil
ne peut causer d'interférences, et (2) cet appareil doit accepter toute
interférence, y compris les interférences quipeuvent causer un mauvais
fonctionnement de l'appareil.

User Manual
using an antenna of a type and maximum (or lesser) gain approved for the
radio peut fonctionner avec une antenne dun type et dun gain maximal (ou
Under Industry Canada regulations, this radio transmitter may only operate
transmitter by Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire
les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il
faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée quivalente (p.i.r.e.) ne dépassepas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiating element of this device and the
user.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
AAX74688001
'
'
3page
Avis d'Industrie Canada sur l'exposition aux rayonnements
Cet appareil est conforme aux limites d'exposition aux rayonnements d'Industrie
Canada pour un environnement non contrôlé. Cet appareil doit être installé et
utilisé à distance minimum de 20cm entre l'élément rayonnant de cet appareil et
l'utilisateur.
REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFÉRENCES
RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES
APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT
ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE
FONCTIONNER
L'APPAREIL