LG 9QK MAX620 User Manual

OWNER’S MANUAL
DIGITAL MEDIA RECEIVER
Please read this manual carefully before operating your set and retain it for future reference.
MAX620BO
ENGLISH
www.lg.com.mx
Getting Started2
Safety Information
CAUTION
1
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to
dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.
(servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a conned space such as a book case or similar unit.
driving, and always be fully aware of all driving condition. Do not change settings,
the presence of uninsulated
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
Always operate the vehicle in a safe manner. Do not become distracted by the vehicle while
or any functions. Pull over in a safe and legal manner before attempting such operations.
Do not use for many hours at extremely low or high temperature. (-10 °C to 60 °C)
To reduce the risk of electric shock, do not remove the cover
or back of this product. There are no user-serviceable parts inside. Refer servicing to qualied service personnel.
To reduce the risk of re or
electric shock, do not expose this
product to dripping or splashing water, rain, or moisture.
The temperature of unit’s outside
can be extremely high, please use
the unit after proper installation in your vehicle.
While driving, keep the sound
volume at a proper level.
Do not drop it and avoid heavy
impacts at anytime.
This unit is for vehicles with a
12-volt battery and negative
grounding. Before installing it in a recreational vehicle, lorry or bus, check the battery voltage. To avoid shorts in the electrical system, be sure to disconnect the E battery cable before beginning the installation.
This device is equipped with a portable battery or accumulator.
Safe way to remove the battery or the battery from the equipment:
Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, re or the like.
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
Table of Contents 3
the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
CAUTION: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC RF Radiation Exposure StatementCompliance Statement
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. End users must follow the specic operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio­frequency wireless devices because their signals could interfere with critical aircraft instruments.
Responsible Party : LG Electronics USA, Inc.1000 Sylvan
AvenueEnglewood Clis, NJ 07632 TEL. : +1-800-243-0000
Table of Contents
1 Getting Started
2 Safety Information
4 Front panel
4 Remote control
5 – Battery Installation
2 Connecting
5 Installation
5 – Basic Installation
5 – Removing the existing
receiver unit
5 – ISO-DIN Installation
6 About detachable control
panel
7 Connection
7 – Connecting to a car
3 Operating
8 Operation
8 – Basic operations
8 – Turning off the sound
temporarily
8 – Using EQ (Equalizer)
8 – Using 3D SOUND
8 – Checking the clock
8 – Turning off the display light
8 – Resetting the unit
8 – Adjusting the general
settings
9 Listening to music from an
external device
9 – Preventing radical changes
in volume as switching
sources
9 Listening to the radio
9 – Storing desired
frequencies manually
10 – Listening to a preset
station
10 – Adjusting TUNER settings
11 Using an SD card
11 – Pausing or restarting SD
card playback
11 – Searching for a section
within a file
11 – Skipping to another file
11 – Checking information
about your music
11 – Playing back files in a way
you want
11 – Quick search of a desired
file
12 Listening to music by
connecting iPod/iPhone
12 – Pausing or restarting
playback
12 – Searching for a section
within a file
12 – Skipping to another file
12 – Checking information
about your music
12 – Playing back files in a way
you want
12 – Playing back files by music
menus
12 – iPod / iPhone CONTROL
MODE
12 – Compatible iPod / iPhone
models
13 Connecting a Bluetooth
wireless technology
13 – Using a Bluetooth wireless
technology
15 – WICS (Wireless Controller
& Synchronization)
16 – Phone compatibility list
4 Troubleshooting
18 Troubleshooting
5 Appendix
19 Specifications
1
2
3
4
5
Getting Started4
1
Getting Started
Front panel
a T
Plays and pauses playback.
• TA (Optional)
Searches stations that have TA / TP information, when it is pressed and held.
SRC / • OFF
b
- When pressed, selects function sources.
- When pressed and held, powers unit on or o.
DISP
c
- Press it, you can check the clock time.
- Press and hold it, you can turn on/o the display window and the light of LED buttons.
• APP
Activates iPod/ iPhone CONTROL MODE.
(EJECT)
d R
Ejects a iPod/ iPhone DOCKING STATION.
Display window
e
iPod/iPhone DOCKING STATION
f
AUX
g
If connected to other portable player, you can enjoy music from it on the unit.
h Y
Skip / Search / Seek / Tune
Returns to the previous step.
Volume knob
i
- Adjusts volume level.
- Confirms the settings.
- Checks tracks, les or preset stations.
j U
Skip / Search / Seek / Tune
CALL/END
- Activates BT function.
- Answers a call.
k 6
Opens the front panel.
Remote Sensor
l
Remote control
SRC / • OFF
a
- When pressed, selects function sources.
- When pressed and held, powers unit o.
FUNC
b
When pressed, sets playback items in each mode.
• MENU
When pressed and held, activates setting menu.
BAND
c
Selects a band in Tuner mode.
DRV
Moves to a next USB drive.
d d/M e f g
Plays or pauses playback. SHF Shues playback. MUTE Temporarily stops the sound. VOLUME W / S
Adjusts volume level.
Connecting 5
2
1
/ v
h c
Skip / Search / Seek / Tune
Returns to the previous step.
/ s
w
- List up / down
- Adjusts settings.
- Moves 10 MP3 / WMA tracks backward or forward if there is no folder or one folder on a SD.
- Moves to the previous or next folder if there are more than 2 folders on a SD.
ENTER / LIST
- Conrms the settings. Checks tracks, les or preset stations.
-
DISP
i
- Press it, you can check the clock
time.
- Press and hold it, you can turn on/
o the display window and the light of LED buttons.
RPT
j
Repeats playback.
INT
k
Intro scan.
Numeric buttons (1 to 6)
l
Selects a numbered preset station in TUNER.
Battery Installation
Type 1
Type 2
Note
,
yUse only one CR2025 (3 V) lithium
battery.
yRemove the battery if the remote
control is not used for a long period of time.
yDo not leave the product in a hot
or humid place.
yDo not handle the battery with
metallic tools.
yDo not store the battery with
metallic materials.
Installation
Basic Installation
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.
Bend the claws according to the thickness of the dashboard.
Control panel
1. Remove the existing receiver unit.
2. Make the necessary connections.
3. Install the installation sleeve.
4. Install the unit into the installation sleeve.
Removing the existing receiver unit
If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed.
1. Remove the rear support from the unit.
2. Remove the control panel and trim ring from the unit.
3. Insert the lever into the hole on one side of the unit. Perform the same operation on the other side and pull the unit out from the mounting sleeve.
ISO-DIN Installation
2
Connecting
Control panel
1. Slide the unit into the ISO-DIN frame.
2. Fit screws removed from the old unit.
3. Slide the unit and frame into the dash opening.
4. Install the dash panel or adapter plate.
(According to models, this step may
not be needed.)
5. Install the trim ring to the unit.
6. Install the control panel to the unit.
Connecting6
About detachable control panel
Attaching the control panel
2
Connecting
1. Align the left side of the panel with the stopper.
2. Push the right side of panel into the unit until it clicks.
Caution
>
yThe control buttons may not work
properly if the control panel is not attached properly. If this occurs, gently press the display.
yDo not leave the control panel
in any area exposed to high temperatures or direct sunlight.
yDo not drop the control panel
or otherwise subject it to strong impact.
yDo not allow such volatile agents
as benzine, thinner, or insecticides to come into contact with the surface of the control panel.
Detaching the control panel
1. Press the 6 to open the control panel.
2. Lift the control panel slightly.
3. Push the control panel to right.
2
3
4. Pull the control panel out of the unit.
5. Put the detached control panel into the protective case.
Control panel
Protective Case
Note
,
Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn o the ignition before cleaning, and remove the key from the ignition switch.
Connection
Connecting to a car
Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.
Wired mic Wired remote input (Black): Hard-wired control adapter can be connected.
Connecting 7
abcd
abcd
efgh
efgh
B f Power Antenna (Blue)
B g Not connected
B c To Ignition (Red)
B d To Battery (+) (Yellow)
B h Ground (-) (Black)
B e Remote On (Blue / White)
B b Not connected
B a Not connected
To Audio out
Sub-woofer Left Sub-woofer Right Front Left Front Right Rear Left Rear Right
Power Antenna
Control Relay
Ignition Switch
Amplier
A
A
A
A
A
A
A
A
a b c d
e f g h
To Audio in
Sub-woofer
Amplier
Caution
>
When being connected in a wrong way, the unit displays as follows.
- Antenna / Remote port short: "ANTENNA/ REMOTE ON PORT SHORT CIRCUIT CHECK"
After connecting it again, restart the unit.
A a Gray : Front Right + A b Gray / Black Stripe: Front Right ­A c Violet : Rear Right + A d Violet / Black Stripe: Rear Right ­A e White : Front Left + A f White / Black Stripe: Front Left ­A g Green : Rear Left + A h Green / Black Stripe: Rear Left -
2
Connecting
Operating8
Operation
Basic operations
1. Turn the unit on by pressing any key on the unit.
2. Select a source by pressing SRC.
3. Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control.
Turning off the sound temporarily
1. Press MUTE to mute your unit. Or press MUTE on the remote control.
2. Press it again to cancel
Using EQ (Equalizer)
3
EQ is to increase or decrease the signal
Operating
strength of audio frequencies. The function helps you to enjoy sound more plentifully. Press EQ on the unit repeatedly. The indicator lights up in the following order.
FLAT /XDSS+ / POP / CLASSIC / ROCK / JAZZ / VOCAL / SALSA / SAMBA / REGGAE / RUSSY / USER1
USER2
/
Using 3D SOUND
This mode delivers outstanding surround sound.
1. Press and hold EQ/ • 3D.
2. Press and hold it again to cancel.
Checking the clock
1. Press DISP.
2. Press it again to cancel.
Turning off the display light
1. Press and hold DISP.
2. Press and hold it again to turn it on.
Note
,
Under the light-o condition, press any key, the light is turned on and then o automatically if you don't press it within a few seconds.
Resetting the unit
You can reset the unit when it does not operate properly.
1. Detach the control panel. Refer to page 6 for detaching the control panel.
2. Press the RESET hole with a sharp object.
Adjusting the general settings
You can adjust [SOUND], [LIGHT] and [OTHER] settings.
On the unit
1. Press and hold • MENU.
2. Rotate the volume knob to select [SOUND], [LIGHT], or [OTHER] and press it.
3. Rotate the volume knob to select the item and press it.
4. Rotate the volume knob clockwise or counterclockwise to adjust the level.
5. Press the volume knob to confirm the setting.
If you want to return to the previous
step, press
On the Remote Control
1. Press and hold FUNC / • MENU.
2. Press w / s to select [SOUND], [LIGHT], or [OTHER] and press ENTER.
3. Press w / s to select the mode and press ENTER.
4. Press w / s to adjust the level.
5. Press ENTER to confirm the setting.
If you want to return to the previous
step, press
.
.
For [SOUND] setting
You can adjust sound quality by adjusting the level BAL (left/right speaker), FAD (front/rear speaker), SW (Subwoofer), SW-F (Subwoofer frequency), A-EQ (Auto EQ).
- When you set the EQ to USER 1/2 mode. : You can adjust the level of BAS (bass), MID (middle), TRB(treble).
ySW (Subwoofer)
You can adjust the volume of subwoofer.
ySW-F (Subwoofer frequency)
OFF/ SW 55 Hz/ SW 85 Hz/ SW 120 Hz You can enable the subwoofer.
yA-EQ (Auto EQ) ON / OFF
AUTO EQ operates only in the music le supported with genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatically selected according to the music genre.
Operating 9
For [LIGHT] setting
You can adjust the light eects by adjusting LED, DIM, or DIM LV.
yLED COL1 / COL2 / AUTO : You can
change the LED window color.
yDIM (Dimmer) OFF / ON : You can
change the brightness of the display window during the power-on status.
Settings Description
DIM ON The display window
becomes dark.
DIM OFF The display window
becomes bright.
yDIM LV (Dimmer Level) : When you set
DIM to ON, you can adjust the dimmer level. (-2, -1, 0, +1, +2)
For [OTHER] setting
yAUX (Auxiliary) ON / OFF
It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit.
yDEMO OFF / ON
You can change the initial indication on the display to information name (function name, EQ name, etc...) while listening to a source.
yBEEP 2ND / ALL
BEEP 2ND : The beep is generated when a key is pressed for longer than 2 seconds. BEEP ALL : The beep is generated when any key is pressed.
yCLK (Clock)
For the model RDS is not supported unit or even for a RDS supported unit.
- When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourelf. Set the clock as follows ;
1. Select a source to TUNER.
2. Press the FUNC to select the CT and
then set CT to OFF. (Refer to the " Adjusting TUNER settings " on the page 11 for setting the CT (Clock Time) ON / OFF.)
3. Press and hold • MENU on the unit to
select [OTHER] and then select CLK by rotating the volume knob.
4. Set the hour by rotating the volume
knob.
5. Press the volume knob to confirm
the hour.
6. Set the minute by rotating the
volume knob.
7. Press the volume knob to confirm
the minute.
- When RDS CT information is received; The clock is displayed according to the RDS CT information.
- When RDS is not supported, set the clock according to 3 to 7 steps.
Listening to music from an external device
1. Connect an external device to the AUX jack with line input cable.
2. Select a source to AUX.
3. Play the connected Auxiliary Equipment.
Preventing radical changes in volume as switching sources
Only when you set AUX to ON as switching sources, you can adjust the volume level of each source to prevent radical changes in volume by selecting GAIN 0 / +6.
1. Press FUNC on the unit. Or press FUNC / • MENU on the remote control.
2. Rotate the volume knob on the unit. Or press w / s on the remote control to set the option. (GAIN 0 / +6)
3. Press the volume knob on the unit. Or press ENTER on the remote control to confirm the setting.
4. If you want to return to the previous step, press
Or press
.
on the remote control.
Listening to the radio
1. Press SRC repeatedly to select a source to TUNER.
2. Press BAND repeatedly to select a desired band.
3. For manual search, press and hold
Y/U
is displayed. Then press it repeatedly to select a desired frequency. Or press and hold c / v on the remote control.
For auto search, press
the unit. Then “SEARCH” is displayed. (Except MW) Or press c / v on the remote control.
Storing desired frequencies manually
1. Press BAND to select a desired band you want to store.
2. Select the desired frequency by using
Y/U
Or use c / v on the remote control.
3. Press the volume knob and rotate the volume knob to select a preset station among 1 to 6 and then press and hold the volume knob until the beep sound is heard. Or press and hold one of preset buttons among 1 to 6 on the remote control until the beep sound is heard.
4. Repeat steps 1 to 3 to preset other stations.
on the unit until “MANUAL“
on
Y/U
on the unit.
3
Operating
Operating10
Note
,
When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased.
Listening to a preset station
1. Press BAND repeatedly to select a desired band.
2. Press the volume knob on the unit. Or press ENTER on the remote control.
3. Rotate the volume knob to select a preset station. Or press w / s on the remote control.
4. Press the volume knob.
3
Operating
Or press ENTER on the remote control.
Or Press BAND and then press the desired
preset button among 1 to 6 on the remote control.
Adjusting TUNER settings
On the unit
1. Press FUNC.
2. Rotate the volume knob to select an item and press it.
3. Rotate the volume knob to set the option and press it.
4. If you want to return to the previous step, press
On the Remote Control
1. Press FUNC / • MENU.
2. Press w / s to select an item and press ENTER.
3. Press w / s to set the option and press ENTER.
4. If you want to return to the previous step, press
yPTY (Program type, RDS (OPTIONAL))
It searches the radio stations by program type of FM tuner. The program types are displayed as follows.
NEWS FINANCE EASY M
AFFAIRS CHILDREN LIGHT M
INFO SOCIAL CLASSICS
SPORT RELIGION OTHER M
EDUCATE PHONE IN JAZZ
DRAMA TRAVEL COUNTRY
CULTURE LEISURE NATION M
SCIENCE DOCUMENT OLDIES
VARIED POP M FOLK M
WEATHER ROCK M
.
.
yA / S (Auto Store)
The six strongest broadcasting frequencies will be stored under preset button 1 to 6 in the order of their signal strength. To cancel, press the volume knob.
yP / S (Preset scan)
Each preset station appears. To cancel, press the volume knob.
ySENS (Tuner sensitivity) MID / HI / LOW
In an area in which signal reception is weak, it helps the tuner to search more stations. The weaker the reception is, the lower option you should set to.
RDS (OPTIONAL)
yAF (Alternative Frequency) ON / OFF
When the reception quality drops, the tuner automatically changes to another station in the network, broadcasting a better reception quality, using the PI and AF codes.
yREG (Region) ON / OFF
REG ON : The unit switches to another station, within the same network, broadcasting the same program when the receiving signals from the current station become weak. REG OFF : The unit switches to another station, within the same network when the receiving signals from the current station become weak. (In this mode, the program may dier from the one currently received.)
yTA (Trac Announcement) ALARM /
SEEK TA ALARM : When the tuned station has no TP information for 5 seconds, a double beep sound is output. TA SEEK : When the tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station that has the TP information.
yPI (Programme Identication) SOUND /
MUTE PI SOUND : When the frequency of a tuned station switches to an AF (Alternative frequency) with an unidentied PI, it keeps the sound. PI MUTE : When the frequency of a tuned station switches to an AF with an unidentied PI, it mutes the sound until the PI is identied.
yCT (Clock Time) ON / OFF
You can use the RDS CT information to update the time. When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourself. Refer to the page 9 for setting the clock.
Operating 11
Using an SD card
1. Open the USB cover.
2. Connect the USB device.
3. Press SRC repeatedly to select a source to USB.
Pausing or restarting SD card playback
1. PressT on the unit to pause playback. Or press
2. Press it to resume playback.
Searching for a section within a file
1. Press and hold for about 1 second during playback. Or press and hold c / v on remote control.
2. Press T on the unit at the point you want. Or press
Skipping to another file
Press
Y/U
Or press c / v on the remote control.
To skip to previous le, press briey
Y
time.
on the remote control.
d/M
Y/U
on the remote control.
d/M
on the unit.
Note
,
within 3 seconds of playing
on the unit
Checking information about your music
MP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA le playback. If there is no information, "NO TEXT" will be shown in the display window.
Playing back files in a way you want
For using applicable buttons
1. Press INT / RPT / SHF.
2. Press it again to cancel.
Using the FUNC button
On the unit
1. Press FUNC.
2. Rotate the volume knob to select an item and press it.
3. Rotate the volume knob to select the option.
4. Press the volume knob to set the option. If you want to return to the previous step, press
Or
.
On the Remote Control
1. Press FUNC / • MENU.
2. Press w / s to select an item and press it.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous
step, press
yRPT (Repeat)
The current selected le (1 RPT) or les in the current selected folder ( is played repeatedly.
ySHF (Shue)
All les (SHF) or each les in the current selected folder ( randomly. During random playback, even if you press Y, you won't go back to the previous le.
yINT (Intro Scan)
The rst 10 seconds of all les (INT) or each les in the current selected folder
INT) are played.
(
.
RPT)
SHF) are played
Quick search of a desired file
1. Press the volume knob on the unit. Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a desired ROOT or folder and press it. Or press w / s and press ENTER on the remote control.
3. Rotate the volume knob on the unit to select a desired file and press it. Or press w / s and press ENTER on the remote control.
The making of unauthorized copies of copy-protected material, including computer programs, les, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal oense. This equipment should not be used for such purposes.
Be responsible
Respect copyrights
3
Operating
Operating12
Listening to music by connecting iPod/iPhone
You can enjoy iPod / iPhone-stored music on the unit by connecting it to the USB connector using the appropriate cable.
1. Open the USB cover.
2. Connect the iPod / iPhone.
3. Press SRC to select a source to USB.
Pausing or restarting playback
1. Press T on the unit to pause playback. Or press
2. Press it to resume playback.
Searching for a section
3
within a file
Operating
During playback, press and hold
and then release at a point you want.
U
Skipping to another file
Press
Y/U
Or press c / v on the remote control.
1. Press the volume knob on the unit. Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a desired category and press it. Or press w / s and press ENTER on the remote control.
3. Rotate the volume knob on the unit to select a desired file and press it. Or press w / s and press ENTER on the remote control.
on the remote control.
d/M
on the unit.
Checking information about your music
MP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.
Press DISP repeatedly during MP3 / WMA le playback. If there is no information, "NO TEXT" will be shown in the display window.
Playing back files in a way you want
On the Unit
1. Press FUNC.
2. Rotate the volume knob to select an item and press it.
3. Rotate the volume knob to select the option.
Y/
Or
4. Press the volume knob to set the option. If you want to return to the previous step, press
.
On the Remote Control
1. Press RPT / SHF.
2. Press it again to cancel.
1. Press FUNC / • MENU.
2. Press w / s to select an item and press ENTER.
3. Press w / s to select the option.
4. Press ENTER to set the option.
If you want to return to the previous
step, press
yRPT (Repeat)
The current selected le (1 RPT) or les on the iPod / iPhone is played repeatedly.
Or
.
ySHF (Shue)
Each le in the currently selected album (
SHF) or all of the les (SHF) on the iPod / iPhone are played randomly. During random playback, even if you press Y, you won't go back to the previous le.
ySPD (BOOK SPEED)
You can adjust the audiobook speed of iPod / iPhone to NOR (Normal), SLOW or FAST.
Playing back files by music menus
You can check les by music menus and play it back.
The music menus are as follows. PLAYLISTS / ARTISTS / ALBUMS /
GENRES / SONGS / COMPOSER / AUDIO BOOK / PODCAST / ...
Press the volume knob on the unit.
1. Or press ENTER on the remote control.
2. Rotate the volume knob on the unit to select a music menu and press it. Or press w / s on the remote control.
3. Rotate the volume knob on the unit to select a file. Or press w / s on the remote control.
4. Press the volume knob on the unit to confirm the setting. Or press ENTER on the remote control.
5. If you want to return to the previous step, press
Or press on the remote control.
.
iPod / iPhone CONTROL MODE
You can control on the unit and iPod / iPhone.
yPress iPOD on the unit. Then playback
is paused. And you can control on the unit and iPod / iPhone.
yWhile using the iPod/iPhone CONTROL
MODE, any functions are not available on the unit.
yPress iPOD again to cancel the iPod /
iPhone CONTROL MODE.
Compatible iPod / iPhone models
yiPod classic yiPod nano 6th generation yiPod touch 4th generation yiPhone 3G / 3GS / 4
We recommend that you use the
OS Version 4.2.1 or more.
Loading...
+ 28 hidden pages