Please read this manual carefully before operating your
set and retain it for future reference.
MODEL
LW130W
1
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or modification
is made.
REGULATORY INFORMATION: FCC Part 15
This product complies with FCC Part 15B, Class B Limits: This device complies with
part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Radiated Energy
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on. The user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
2
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer
or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission rules.
• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries
of this product in the end user.
1. To comply with FCC RF exposure compliance requirements, a
separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons.
2. This Transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the
same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
Holes in metal, through which insulated wires pass, shall have smooth well rounded
surfaces or shall be provided with brushings.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numÈrique de la classe B est conforme ‡ la norme NMB-003 du.
Warning: Do not install this equipment in a confined space such as a bookcase or
similar unit.
Warning:
Wiring methods shall be in accordance with the National Electric Code,
ANSI/NFPA 70.
Warning: This is a class B product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do not expose this product to rain
or moisture.
Caution: This installation should be made by a qualified
Service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
Caution: The apparatus shall not be exposed to water (dripping or splashing) and no
objects filled with liquids, such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains cord plug. When installing the
product, ensure that the plug is easily accessible.
3
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where you purchased
the product.
EEE Compliance with Directive. (for Turkey only)
LG Electronics hereby declares that this/ these product(s) is/are in compliance with
the essential requirements and other relevant provisions of Directive 2004/108/EC,
2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere. The
Netherlands (Tel : +31-(0)36-547-8888)
4
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
5
Cautions for Safe Operation
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be cautious not to get
combustible or metallic material inside the body. If used with foreign matter inside, the
device is liable to fail or to get cause of fire or electric shock.
Remove dust or dirt on the surface of the lens with a blower.
Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampened with a
small quantity of neutral detergent then wipe dry.
Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides.
They may damage the surface finish and/or impair the operation of the
Operating and storage location
Avoid viewing a very bright object (such as light fittings) during an extended period.
Avoid operating or storing the unit in the following locations.
• Extremely hot or cold places (operating temperature from -10 °C to 50 °C, however,
we recommend that the unit be used within a temperature range from 0 °C to 45 °C)
Damp or dust place
Places exposed to rain
device.
Places subject to strong vibration
Close to generators of powerful electromagnetic radiation such as radio or TV
The LG Network Camera is designed to use on an Ethernet and Wireless netwo rk and must
be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the LG Network Camera in
your networking environment. Some knowledge of networking environments would be
beneficial to the reader.
Should you require any technical assistance, please contact authorized service center.
Dual H.264 Stream for single Video Input
Multi-Codec (H.264, MJPEG) Streaming
Audio Support (G.711, G.726 Full Duplex)
Ethernet 100Mbps
Wireless LAN 802.11b/g/n
Digital IN/OUT: Input 1port, Output 1port
MicroSD Memory extension (~32GB)
Pre/Post Alarm support
Human motion detection support
Flash LED (5meter)
AW, AE, AG support
8
Part Names and Functions
Part Names and Functions
① Camera installation hole
Use this hole to install the camera on the wall or ceiling.
External device connectors
②
A IN(R)/A IN (Sensor input) Terminals: Provide physical interface for sensor.
A OUT(R)/A OUT (Relay output) Terminals: Provide physical interface for Alarm/Relay.
Power source terminal
③
Connect to a DC 5V power supply using proper cables.
ETHERNET
④
Connect to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable
attached RJ-45 connector
RESET button
⑤
Push the button, this would restart the device.
WPS(Wi-Fi Protected Setup), Factory Reset button
⑥
Push the button to use WPS or Factory Reset Function.
Push the button less than 4 seconds, this would trigger WPS.Push the button more than 10
seconds and Pop the button, this would trigger Factory Reset. When connecting AP using WPS,
wireless LAN connection lamp blinks red and green. When it stops blinking and color of it is
green, connection is completed. When it stops blinking and color of it is red, connection is failed.
Note:
Usage of WPS refers to the internet or access pointer manual. If access point sets
shared mode, you cannot connect access point using WPS.
9
⑦
Micro SD Card slot cover
Micro SD Card slot
⑧
Insert micro SD card.
⑨
Speaker
Transmit Mic sound of PC.
⑩
Motion detection sensor
Detect movement around.
⑪
Flash LED
Light on when event is occurred.
⑫ Mic
Listen sound of camera surround.
⑬ Power indicator
The Green LED lights when the camera is powered.
⑭ Ethernet connection indicator
The Green LED lights when the Ethernet is connected.
⑮ Wireless LAN connection indicator
The Green LED lights when the Wireless LAN is connected.
10
Connections
Precautions
Be sure to switch off the unit before installation and connection. The installation
should be made by qualified service personnel or system installers. Do not expose
the power and connection cables to moisture, which may cause damage to the unit.
11
Connections
Connecting Network
You can control and monitor the system via network. With the remote control
(monitoring), you can change the system configuration or monitor the image via
network.
Connect to the DC 5 V UL Listed, Class 2 Power Supply only on the
unit. (Recommended power adapter is DC 5V/1.5A or above)
12
Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches,
etc. Specification of alarm terminal is shown as bellow.
[Alarm terminal specification]
Minimum Typical Maximum Note
Digital Input 2.3V 3.3V 4.3V
Digital Output 2.3V 3.3V
AWG 24 AWG 16 UL Standard Connectable
cable
Absolute Maximum Ratings
- Digital Input: -24V to +24VDC
- Digital Output: +3V to +24VDC / 100mA Max
Connect connectable cable to alarm terminal.
While disconnecting, push A button.
0.20 mm
2
1.5mm2 IEC Standard
13
14
Connections
Using the micro SD card
You can record your surveillance environment with the micro SD card even if the
network is disconnected condition.
To insert the micro SD card
1. Open the micro SD Card Slot Cover.
2. Insert the micro SD card carefully as shown in the following illustrations. Make
sure the micro SD card terminal position before insert the micro SD card. Push
the back end of the micro SD card to fix it at the last step.
Notes:
Do not use the power too much when you insert the micro SD card. The micro SD
card may be damaged.
If you insert the micro SD card in the wrong position, the micro SD card may be
damaged or it may cause the malfunction of the micro SD Card Slot.
Keep the terminal part of the micro SD card in clean. Be careful the terminal part of
the micro SD card not to dusty.
As the micro SD card is consumable, the micro SD card end its days and may be not
able to save data if you use it more than over certain times. In this case, replace micro
SD card to buy a new one.
15
Caution:
If you install the micro SD card on the camera and remove the micro SD card during operation,
you must unmount the micro SD card by using the [SD Card > Configuration > Disk
Management > Unmount] menu. The micro SD card data is compromised or the camera may
not operate normally, if you remove the card without use [Unmount] function.
LG Electronics is not responsible for deleted data caused by user mishandling when you insert
or remove the micro SD card.
Recommended the micro SD card specification
Block Size
Manufacturer Capacity
(FAT 32)
LG
Sandisk
Transcend
Less than
32 kbyte
32 GB
Speed of reading and writing more than 10
16
Note
MB/Second (Class 6)
Loading...
+ 35 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.