LG 9QKE40410 Users manual

© Copyright 2003, Zenith Electronics Corporation
Installation and Operating Guide | Warranty
Model Number | RC59000M |VCR / DVD Recorder
CD-R/RW
2
Safety Precautions
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit.
NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
CAUTION:
This VCR/DVD Recorder employs a Laser System. To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service center.
Use of controls, adjustments, or the performance of proce­dures other than those specified herein may result in haz­ardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifi­cations are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
FCC COMPLIANCE: The responsible party for this product’s compliance is: Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000
SERIAL NUMBER: The serial number is found on the back of this unit. This number is for this unit only. You should record requested information here and retain this guide as a perma­nent record of your purchase.
Model No. ___________________________________ Serial No. ___________________________________
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
WARNING: TO REDUCE THE RISK OF FIRE OR ELEC­TRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
INTRODUCTION
3
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions. - All these safety and oper-
ating instructions should be read before the product is operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future refer­ence.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this product near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water.
6. Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions. -
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over- heating. The open­ings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This prod­uct should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is pro­vided or the manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as radi­ators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A ground­ing
type plug has two blades and a third ground­ing prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over.
13. Unplug this product during lightning storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped.
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNERS MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following proce­dures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
4
Table of Contents
INTRODUCTION
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . 4-5
RC59000M Overview . . . . . . . . . . . . . . . . . . . . 6-9
Recordable Discs . . . . . . . . . . . . . . . . . . . . . . . 6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disc-related terms . . . . . . . . . . . . . . . . . . . . . . 6
Types of video CDs . . . . . . . . . . . . . . . . . . . . . 6
About DVD-R and DVD-RW disc. . . . . . . . . . . . 7
What are ‘recording modes’? . . . . . . . . . . . . . . 7
• Is editing a DVD like editing a video tape? . 7
• About word ‘Original’ and ‘Playlist’ . . . . . . . 7
About DVD recording. . . . . . . . . . . . . . . . . . . 7-8
• Disc types and recording formats, modes,
and settings . . . . . . . . . . . . . . . . . . . . . . . . 7
• Notes for recording. . . . . . . . . . . . . . . . . . . 8
• Recording TV audio channels. . . . . . . . . . . 8
• Restrictions on video recording. . . . . . . . . . 8
• What is ‘CPRM’? . . . . . . . . . . . . . . . . . . . . 8
• Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• Handling the unit . . . . . . . . . . . . . . . . . . . . 9
• Cleaning the unit . . . . . . . . . . . . . . . . . . . . 9
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . 9
• Handling discs . . . . . . . . . . . . . . . . . . . . . . 9
• Storing discs . . . . . . . . . . . . . . . . . . . . . . . 9
• Cleaning discs . . . . . . . . . . . . . . . . . . . . . . 9
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . 9
• About the symbol display . . . . . . . . . . . . 9
• About the disc symbols for instructions. . . . 9
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Function Display Window . . . . . . . . . . . . . . . . 11
Remote Control Overview . . . . . . . . . . . . . . . . 12
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DVR HOOKUP
Connections . . . . . . . . . . . . . . . . . . . . . . . . 14-17
Connecting Antenna/Cable TV to
VCR/DVD Recorder . . . . . . . . . . . . . . . . . . . . 14
Connecting to a TV. . . . . . . . . . . . . . . . . . . . . 15
Connecting to Optional Equipment . . . . . . . . . 16
Accessory Audio/Video (A/V) Connections
to VCR/DVD Recorder . . . . . . . . . . . . . . . . . . 17
Connecting a Digital Camcorder . . . . . . . . . . . 17
Before Operation. . . . . . . . . . . . . . . . . . . . . 18-28
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . 18
General Operation . . . . . . . . . . . . . . . . . . . . . 18
General . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
• Auto Channel Scan . . . . . . . . . . . . . . . . . 18
•To Add or Erase Channels from Memory . 18
• Auto Clock Set. . . . . . . . . . . . . . . . . . . . . 19
• Manual Clock Set. . . . . . . . . . . . . . . . . . . 19
• TV Aspect Ratio . . . . . . . . . . . . . . . . . . . . 19
• Progressive Scan. . . . . . . . . . . . . . . . . . . 20
• PBC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
• Factory Setting. . . . . . . . . . . . . . . . . . . . . 20
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
• Display Menu. . . . . . . . . . . . . . . . . . . . . . 20
• Disc Language. . . . . . . . . . . . . . . . . . . . . 20
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
• Dolby Digital. . . . . . . . . . . . . . . . . . . . . . . 21
• DTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
• MPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
• Sampling Freq. (Frequency). . . . . . . . . . . 21
• Dynamic Range Control (DRC). . . . . . . . . 21
•Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lock (Parental Control) . . . . . . . . . . . . . . . 22-23
• Movie Rating . . . . . . . . . . . . . . . . . . . . . . 22
• Set Password. . . . . . . . . . . . . . . . . . . . . . 22
• Country Code. . . . . . . . . . . . . . . . . . . . . . 23
Recording . . . . . . . . . . . . . . . . . . . . . . . . . 23-24
• DISC Record Mode . . . . . . . . . . . . . . . . . 23
• VCR Record Mode. . . . . . . . . . . . . . . . . . 23
• Record Aspect Ratio. . . . . . . . . . . . . . . . . 24
• DV Rec Audio . . . . . . . . . . . . . . . . . . . . . 24
Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
• DISC Initialize . . . . . . . . . . . . . . . . . . . . . 24
• Disc Protect . . . . . . . . . . . . . . . . . . . . . . . 24
• Disc Finalize . . . . . . . . . . . . . . . . . . . . . . 25
• Disc Name. . . . . . . . . . . . . . . . . . . . . . . . 25
General Explanation of On-Screen Display . . . 26
Displaying Disc Information on-screen . . . . . . 26
Displaying OSD While Watching TV . . . . . . . . 26
• Changing TV Channels . . . . . . . . . . . . . . . . 26
• Changing TV Audio Channel . . . . . . . . . . . . 26
Table of Contents
PLAYBACK
Operation with DVD and Video CD. . . . . . . 29-32
Playing a DVD or Video CD . . . . . . . . . . . . . . 29
• Moving to another TITLE . . . . . . . . . . . . . 29
• Moving to another CHAPTER/TRACK . . . 29
• Slow Motion . . . . . . . . . . . . . . . . . . . . . . . 29
Still Picture and Frame-by-Frame Playback
. 30
• Search. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Random. . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . 30
•Time Search. . . . . . . . . . . . . . . . . . . . . . . 30
• Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
• Marker Search . . . . . . . . . . . . . . . . . . . . 31
• Checking the contents of DVD Video discs:
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
•Title Menu . . . . . . . . . . . . . . . . . . . . . . . . 31
• Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . 31
• Camera Angle . . . . . . . . . . . . . . . . . . . . . 31
• Changing the Audio Language . . . . . . . . . 31
• Changing the Audio Channel . . . . . . . . . . 32
• 3D Surround . . . . . . . . . . . . . . . . . . . . . . 32
• Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . 32
• Finding Locations on a Disc . . . . . . . . . . . 33
• Last Condition Memory. . . . . . . . . . . . . . . 33
Audio CD and MP3 Operation. . . . . . . . . . . 34-37
Playing an Audio CD or MP3 Disc. . . . . . . . . . 34
Notes on MP3 Recordings . . . . . . . . . . . . . . . 34
• Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
• Moving to Another Track. . . . . . . . . . . . . . 34
• Repeat Track/All/Off . . . . . . . . . . . . . . . . . 34
• Random . . . . . . . . . . . . . . . . . . . . . . . . . . 34
• Search . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . 34
Programmed Playback with Audio CD and MP3
. 35
Viewing a JPEG Disc
. . . . . . . . . . . . . . . . . . . . . 36
• Moving to Another file. . . . . . . . . . . . . . . . 36
•To rotate the picture . . . . . . . . . . . . . . . . . 36
•To view Slide Show . . . . . . . . . . . . . . . . . 36
VCR Mode Tape Playback
Normal Playback Tracking Control
Special Effect Playback . . . . . . . . . . . . . . . . . . .
• Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
• Still Picture and Frame-by-Frame Playback . 37
• Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . 37
RECORDING
Basic Recording . . . . . . . . . . . . . . . . . . . . . 38-39
Basic Recording from a TV . . . . . . . . . . . . . . . 38
Instant Timer Recording . . . . . . . . . . . . . . . . . 38
Copying from DVD to VCR . . . . . . . . . . . . . . . 39
Copying from VCR to DVD . . . . . . . . . . . . . . . 39
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . 40
Checking Timer Recording Details . . . . . . . . . 40
Canceling a Timer Recording . . . . . . . . . . . . . 40
Stopping a Timer Recording in Progress . . . . . 40
Timer Recording Troubleshooting . . . . . . . . . . 40
Recording from an External Input . . . . . . . 41-42
Recording from External Components. . . . . . . 41
Recording from a Digital Camcorder . . . . . . . . 41
Playing your recordings on other DVD players
. . 41
• Finalizing a Disc. . . . . . . . . . . . . . . . . . . . 41
What is DV? . . . . . . . . . . . . . . . . . . . . . . . . . . 42
•DV-Related Messages . . . . . . . . . . . . . . . 42
•Troubleshooting . . . . . . . . . . . . . . . . . . . . 42
EDITING
VR Mode: Original and Playlist Editing . . . 43-48
Titles and Chapters. . . . . . . . . . . . . . . . . . . . . 43
Adding Chapter Markers . . . . . . . . . . . . . . . . . 43
Using Original (Title) menu . . . . . . . . . . . . . . . 43
Using Original (Chapter) menu . . . . . . . . . . . . 44
Using Playlist (Title) menu. . . . . . . . . . . . . . . . 44
Using Playlist (Chapter) menu. . . . . . . . . . . . . 45
Naming a Title . . . . . . . . . . . . . . . . . . . . . . . . 45
Making a New Playlist. . . . . . . . . . . . . . . . . . . 46
Adding Additional Title/Chapters to the Playlist 46 Erasing an Original or Playlist Title/Chapter. . . 47
Combining Two Chapters Into One . . . . . . . . . 47
Changing Title or Chapter Thumbnails . . . . . . 47
Moving a Playlist Chapter . . . . . . . . . . . . . . . . 48
Deleting a Part . . . . . . . . . . . . . . . . . . . . . . . . 48
Video Mode: Original editing . . . . . . . . . . . . . . 49
Using Title List . . . . . . . . . . . . . . . . . . . . . . . . 49
If the disc has already been finalized . . . . . . . 49
Erasing a Title. . . . . . . . . . . . . . . . . . . . . . . . . 49
REFERENCE
Language Code List. . . . . . . . . . . . . . . . . . . . . 50
Country Code List . . . . . . . . . . . . . . . . . . . . . . 51
Troubleshooting . . . . . . . . . . . . . . . . . . . . . 52-53
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 54
About the symbols for instructions
Indicates hazards likely to cause harm to the unit itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
INTRODUCTION
5
6
RC59000M Overview
Recordable Discs
12cm/8cm, single-sided, single layer disc Approx. max. recording time (XP mode): 240 minutes (4.7GB), 80 minutes (1.46GB)
12cm/8cm, single-sided, single layer disc Approx. max. recording time (XP mode): 240 minutes (4.7GB), 80 minutes (1.46GB)
otes
– This recorder cannot record CD-R or CD-RW discs. – DVD-R/RW and CD-R/RW discs recorded using a
personal computer or a DVD or CD recorder may not play if the disc is damaged or dirty, or if there is dirt of condensation on the recorder’s lens.
– If you record a disc using a personal computer, even
if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)
Playable Discs
DVD (8 cm/12 cm disc)
Video CD (VCD) (8 cm / 12 cm disc)
Audio CD (8 cm/12 cm disc)
In addition, this unit can play a CD-R or CD-RW that contains audio titles or MP3 files, DVD-R, DVD-RW, and SVCD.
otes
– Depending on the conditions of the recording equip-
ment or the CD-R/RW (or DVD-R/-RW) disc itself, some CD-R/RW (or DVD-R/-RW) discs cannot be played on the unit.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.
Regional code of the VCR/DVD Recorder and DVDs
This VCR/DVD Recorder is designed and manu­factured for playback of Region 1 encoded DVD software. The region code on the labels of some DVD discs indicates which type of VCR/DVD Recorder can play those discs. This unit can play only DVD discs labeled 1 or ALL. If you try to play any other discs, the message “Incorrect region code. Can’t play­back” will appear on the TV screen. Some DVD discs may not have a region code label even though their play­back is prohibited by area limits.
otes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs may be intentionally fixed by software manufacturers. As this unit plays DVDs and Video CDs according to disc content designed by the software manufacturer, some playback features of the unit may not be available or other functions may be added. Refer also to the instructions supplied with the DVDs and Video CDs. Some DVDs made for business pur­poses may not be played on the unit.
Disc-related terms
Title (DVD only)
The main film content or accompanying feature content or music album. Each title is assigned a title reference number enabling you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller than titles. A title is composed of one or several chap­ters. Each chapter is assigned a chapter number to enable you to locate the chapter you want. Depending on the disc, chapters may not be labeled.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD or an audio CD. Each track is assigned a track number, enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions, moving pictures and still pictures are divided into sec­tions called “Scenes”. Each scene available is displayed on the Scene menu and assigned a scene number, enabling you to locate the scene you want. A scene may be composed of one or several tracks.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact with the system via menus, search functions, or other typical computer-like operations. Moreover, high resolu­tion still pictures can be played if they are included on the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs allow playback of video pictures as well as sound, but they are not equipped with PBC.
1
INTRODUCTION
7
RC59000M Overview (Continued)
About DVD-R and DVD-RW disc
How are DVD-R and DVD-RW discs different?
The essential difference between DVD-R and DVD-RW is that DVD-R is a record-once medium, while DVD-RW is a re-recordable/erasable medium. You can re-record/ erase a DVD-RW disc approximately 1,000 times.
Can I play my recordable discs in a regular DVD player?
Generally, DVD-R discs and DVD-RW discs recorded in Video mode are playable in a regular DVD player, but they must be ‘finalized’ first. This process fixes the con­tents of the disc to make them readable to other DVD players as DVD-Video discs. DVD-RW discs recorded in VR (Video Recording) mode are playable in some players.
This indicates a product feature that is capa­ble of playing DVD-RW discs recorded with Video Recording format.
What are ‘recording modes’?
There are two recording modes available using this recorder: VR mode and Video mode. When recording to a DVD-R disc, recordings are always in Video mode. DVD-RW discs can be formatted for VR mode recording or Video mode recording.
VR mode recording
•3 different picture quality/recording time settings avail­able (SP, LP, XP)
• Not playable on regular DVD players
• Recordings can be extensively edited
Video mode recording
•3 different picture quality/recording time settings avail­able (SP, LP, XP)
• Playable on regular DVD players (after finalizing)
• Limited editing features
Many functions of this recorder are dependent on the recording mode. One or more of the symbols ( , ) appear by each function explained in this manual so that you can see at a glance whether it’s relevant for the disc loaded. You can find more information on disc formats and recording modes on next page.
ote
DVD-Video Format (Video mode) is a new format for recording on DVD-R/RW discs that was approved by the DVD Forum in 2000. You may therefore experience problems playing recordable DVD discs in some play­ers. Symptoms include video artifacts, audio and/or video dropouts and playback suddenly stopping. Our company cannot take responsibility for problems playing discs recorded on this recorder in other players.
Is editing a DVD like editing a video tape?
No. When you edit a video tape you need one video deck to play the original tape and another to record the edits. With DVD, you edit by making a ‘Playlist’ of what to play and when to play it. On playback, the recorder plays the disc according to the Playlist.
About word ‘Original’ and ‘Playlist’
Throughout this manual, you will often see the words Original and Playlist to refer to the actual content and the edited version.
Original: content refers to what’s actually recorded on the disc.
Playlist: content refers to the edited version of the disc — how the Original content is to be played.
About DVD recording
otes
• This recorder cannot make recordings on CD-R or CD-RW discs.
• Our company takes no responsibility for recording fail­ure due to power cuts, defective discs, or damage to the recorder.
• Fingerprints and small scratches on a disc can affect playback and/or recording performance. Please take proper care of your discs.
Disc types and recording formats, modes, and settings
This recorder can play three different kinds of DVD disc: pre-recorded DVD-Video discs, DVD-RW and DVD-R discs. The disc format for DVD-R discs is always “Video format”—the same as pre-recorded DVD-Video discs. This means that once finalized, you can play a DVD-R in a regular DVD player.
By default, the DVD-RW disc format is Video Recording format, though you can change this to Video format, if required. (Reinitializing the disc will erase the contents of the disc.)
The recording mode is closely related to the disc for­mat. If the disc format is Video Recording format, then the recording mode is VR mode; if the disc format is Video mode, then the recording mode is Video mode (except for DVD-Video, which is not recordable, and so does not have a recording mode). Within the recording modes (which are fixed for the whole disc) are the record settings. These can be changed as required for each recording and determine the picture quality and how much space the recording will take up on the disc.
VR
Video
RC59000M Overview (Continued)
Notes for recording
• The recording times shown are not exact because the recorder uses variable bit-rate video compression. This means that the exact recording time will depend on the material being recorded.
• When recording a TV broadcast, if the reception is poor or the picture contains interference, the record­ing times may be shorter.
• If you record still pictures or audio only, the recording time may be longer.
• The displayed times for recording and time remaining may not always add up to exactly the length of the disc.
• The recording time available may decrease if you heavily edit a disc.
• If using a DVD-RW disc, make sure you change the recording format (Video mode or VR mode) before you record anything on the disc. See page 24 (DISC Initialize) for how to do this.
• When using a DVD-R disc, you can keep recording until the disc is full, or until you finalize the disc. Before you start a recording session, check the amount of recording time left on the disc.
• When using a DVD-RW disc in Video mode, recording time available will only increase if you erase the last title recorded on the disc.
• The Erase Title option in the Original (Title) menu only hides the title, it does not actually erase the title from the disc and increase the recording time available (except for the last recorded title on a DVD-RW disc in Video mode).
Recording TV audio channels
This recorder can record one or two channel audio. For TV broadcasts, this usually means mono or stereo, but some programs are broadcast with a main and a SAP (Secondary Audio Program) audio channel. If you’re recording in Video mode (or in VR mode), you can record either the main audio or the SAP audio.
Restrictions on video recording
•You cannot record copy-protected video using this recorder. Copy-protected video includes DVD-Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording, recording will pause or stop automatically and an error message will be displayed on-screen.
•Video that is ‘copy-once only’ can only be recorded using a DVD-RW disc in VR mode with CPRM (see below).
What is ‘CPRM’?
CPRM is a copy protection system (with scramble sys­tem) only allowing the recording of ‘copy once’ broad­cast programs. CPRM stands for Content Protection for Recordable Media. This recorder is CPRM compatible, which means that you can record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can only be made on DVD-RW discs format­ted in VR mode, and CPRM recordings can only be played on players that are specifically compatible with CPRM.
Copyright
• Audio and video recordings you make using this recorder are for your personal use only. You may not sell, lend or rent them to other people.
•This product incorporates copyright protection tech­nology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision cor­poration. Reverse engineering or disassembly is pro­hibited.
8
Disc type Disc format Recording mode Functions
DVD-Video Video format n/a Playback only
DVD-RW Video Recording VR mode Playback, recording, Original/Playlist editing
format (default)
Video format Video mode Playback, limited recording, limited editing
DVD-R Video format Video mode Playback, limited recording, limited editing
INTRODUCTION
9
RC59000M Overview (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.
To obtain a clear picture
The VCR/DVD Recorder is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your nearest dealer.
Remote Control Operation Range
Point the remote control at the remote sensor and press the buttons.
Distance: About 23 ft (7 m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
Remote Control Battery Installation
Detach the battery cover on the rear of the remote control, and insert two R03 (size AAA) batteries with and aligned correctly.
Caution
Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).
Notes on Discs
Handling discs
Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints will not get on the surface. Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sun­light, as there may be a considerable temperature increase inside the car.
Cleaning discs
Fingerprints and dust on the disc can cause poor pic­ture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the cen­ter outward.
Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.
About Symbols
About the symbol display
” may appear on the TV screen during operation. This icon means the function explained in this owner’s manual is not available on that specific disc.
About the disc symbols for instructions
Asection whose title has one of the following symbols are applicable only to those discs represented by the symbol.
DVD-R/RW with Video recording mode
DVD-RW with VR recording mode DVD-Video disc Video CDs Audio CDs. MP3 Discs. JPEG Discs. VHS Tape.
VHS
JPEG
MP3
CD
VCD
DVD
VR
Video
NoYes
10
Front Panel
REC (z) button
Starts recording. Press
repeatedly to set the
recording time.
CHANNEL (v / V)
Scans up or down through memorized channels.
PLAY (N)
To play back a disc or tape.
OPEN/CLOSE (Z)
Opens or closes the disc tray.
AV2 (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.).
S-VIDEO IN
Connect the S-Video output of an external source (TV/ Monitor, VCR, Camcorder, etc.).
DV INPUT
Connect the DV output of a digital camcorder.
PAUSE/STEP (X/C)
Pause playback or recording
temporarily/press repeatedly for
frame-by-frame playback.
Disc Tray (DVD deck)
Insert a disc here.
POWER button and indicator
Switches the VCR/DVD Recorder ON and OFF. Lights green when the VCR/DVD Recorder is turned on.
STOP (x)
Stops playback.
COPY
Press to copy DVD to VCR (or VCR to DVD).
Cassette Compartment (VCR deck)
Insert a video cassette here.
EJECT
Ejects the tape in the VCR deck.
DVD/VCR
Toggles control between the DVD
deck and the VCR deck.
FORWARD (M/>)
DVD: Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search.
VCR: Advances the tape during the STOP mode or for fast forward picture search.
BACKWARD (./m)
DVD: Go to beginning of current chapter/track or to previous chapter/track.
Press and hold for a fast reverse search.
VCR: Rewinds the tape during the STOP mode or for fast reverse picture search.
Display window
Shows the current status of
the VCR/DVD Recorder.
Remote Sensor
Point the VCR/DVD Recorder
remote control here.
11
INTRODUCTION
Function Display Window
DVD
PRG TTL VR TRK CHP TV SAP COPY
Hi-Fi ST
XP SP S LP
SVCD
CD
AB
-R W
–RW
REC
ST Indicates a stereo broadcast is
being received.
Disc type indicators
Indicates the type of disc loaded.
Hi-Fi Indicates when the unit is being played a tape or a disc is
being recorded in Hi-Fi.
COPY DVD to VHS (or VHD to DVD) copy is in progress.
SAP Indicates when a SAP BILINGUAL broadcast is being received.
Character indicators
Indicates clock, total playing time, elapsed time, remaining
time, title number, chapter/track number, channel, etc.
REPEAT Indicates repeat mode.
REC The recorder is
recording.
Indicates when the recorder is in timer recording or a timer recording is programmed.
SP, SLP, LP, XP
Indicates recording mode.
PRG Programmed playback active
TTl Indicates current title.
A disc is inserted in the DVD deck.
A VHS tape is inserted in the VCR deck.
A DVD-R or DVD-RW disc is inserted in the DVD deck.
CHP/TRK Indicates current chapter or track number
TV The unit’s functions are available and channels
are selected at TV.
Indicates when the VCR/DVD Recorder is Locked.
TV
12
Remote Control Overview
POWER
Switches the VCR/DVD Recorder ON
and OFF.
TV/VCR
To view channels selected by the VCR
tuner or by the TV tuner.
DVD
Select the VCR/DVD Recorder’s func-
tion mode to DVD.
VCR
Select the VCR/DVD Recorder’s func-
tion mode to VCR.
INPUT
Changes the input to use for recording
(Tuner, AV1, AV2, or DV IN).
0-9 numerical buttons
Selects numbered options in a menu.
Selects TV’s channel.
TV Control Buttons
POWER: Switches TV ON and OFF.
Input: Selects the TV’s source.
CH +/–: Selects TV’s channel.
VOL +/–: Adjusts TV’s volume.
MUTE: Turns on or off TV sound.
REC MODE
Selects the recording mode:
SP, LP, or XP.
TIMER REC
Displays Timer Record menu.
REC (z)
Starts recording. Press repeatedly to set
the recording time.
BACKWARD / FOWARD (m / M)
-
DVD: Search backward or forward.
- VCR: Rewinds the tape during the
STOP mode, for fast reverse picture
search and Advances the tape during
the STOP mode, fast forward picture
search.
SKIP (. / >)
Go to next chapter or track. Returns to
beginning of current chapter or track or
go to previous chapter or track.
AUDIO
Selects an audio language (DVD) or an
audio channel.
SUBTITLE
Selects a subtitle language.
ANGLE
Selects a DVD camera angle,
if available.
ZOOM
Enlarges DVD video image.
OPEN/CLOSE, EJECT
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
COPY
Press to copy DVD to VCR (or VCR to DVD).
CLEAR
Removes a mark on the Marker Search menu.
TITLE
Displays the disc’s Title menu, if available.
DISC MENU / LIST
Accesses menu on a DVD disc. Switches between Original and Playlist.
SETUP
Accesses or removes the Setup menu.
DISPLAY
Accesses On-Screen Display.
Displays information while viewing a TV program.
RETURN
- Removes the menu.
bBvV(left/right/up/down)
Selects an option in the menu.
CH/TRK(
v/V): Selects a program.
Adjusts manually the tape’s picture onscreen.
ENTER
Acknowledges menu selection.
PAUSE/STEP (X)
Pause playback or recording temporari­ly, press again to exit pause mode. press repeatedly for frame-by-frame playback.
PLAY (N)
Starts playback.
STOP (x)
Stops playback or recording.
CHP ADD
Inserts a chapter marker when playing/ recording a VR mode DVD-RW disc.
THUMBNAIL
Selects a thumbnail picture for the current title for use in the Original (Title).
REPEAT
Repeat chapter, track, title, all.
A-B
Repeat sequence.
MARKER
Marks any point during playback.
SEARCH
Displays Marker Search menu.
LOCK
Disables front panel buttons.
RANDOM
Plays tracks in random order.
LOCK
The Lock feature disables the front panel buttons (except EJECT) to prevent children from tampering with the VCR/DVD Recorder. Simply press Lock on the remote control to toggle this feature on and off.
TV
INTRODUCTION
13
Rear Panel
Caution Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
ANT.IN
Connect the VHF/UHF/CATV antenna to this terminal.
COAXIAL (Digital audio out jack)
Connect to digital (coaxial) audio equipment.
AUDIO OUT (Left/Right)
Connect to a TV or other equipment with audio inputs.
VIDEO OUT/AUDIO OUT (Left/Right)
Connect to a TV with video and audio inputs.
COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr)
Connect to a TV with Y Pb Pr inputs.
AV 1 (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source (Audio system, TV/Monitor, VCR, Camcorder).
AC Power Cord
Plug into the power source.
S-VIDEO OUT
Connect to a S-Video Input on TV.
OPTICAL (Digital audio out jack)
Connect to digital (optical) audio equipment.
RF. OUT (DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
Connections
ips
Depending on your TV and other equipment you wish to connect, there are various ways you could connect the recorder. Use only one of the connections described below.
Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.
For better sound reproduction, connect the recorder’s AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See “Connecting to Optional Equipment” on page 16.
Caution
– Make sure the the unit is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the unit’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
– Do not connect your VCR/DVD Recorder via your
VCR. The DVD image could be distorted by the copy protection system.
Connecting Antenna/Cable TV to VCR/DVD Recorder
11
Disconnect the antenna leads from the rear of the TV.
22
Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your Recorder.
ip
If your antenna lead wire is a flat type antenna cable, connect it to an Antenna Adapter (300-ohm to 75-ohm) (not supplied) and slip the Adapter onto the ANT.IN jack. The Adapter does not screw on to the the unit, it just slips over the jack.
Cable Service Without Cable Box
If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the unit. Use the supplied round coaxi­al cable to connect between the VCR/DVD Recorder’s OUT TO TV jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels. (All cable channels.)
Cable Service With Cable Box
If a converter is required in your cable system, follow the instruction below: The cable hookup permits both TV and VCR/DVD Recorder operation.
To view or record a CATV channel 1
Tune the TV to the correct video input channel.
2 Set the VCR/DVD Recorder channel selector to the output
channel of the Cable Converter box using CH (v / V) or number (0-9) of your VCR/DVD Recorder. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
ote
If you are using a cable box to tune channels, it is not neces­sary to do Auto Channel Scan as indicated on page 18.
14
Antenna Antenna
Flat Wire
(300 ohm)
300/75 ohm
Adaptor
(Not supplied)
Cable TV
Wall Jack
OR OR
Rear of VCR/DVD Recorder
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
Rear of VCR/DVD Recorder
DVR HOOKUP
15
Connections (Continued)
Connecting to a TV
Make one of the following connections, depending on the capabilities of your existing equipment.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R).
ote
If you use this connection, tune the TV to the DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCRs RF output channel When the DVD+VCR is turned off,
press and hold
CH/PRESET (v/V) on the front panel for about five seconds to change the RF output channel (CH 03 or CH 04). “RF 03” or “RF 04” appears in the display win­dow.
Audio/Video connection
11
Connect the VIDEO OUT jack on the VCR/DVD Recorder to the video in jack on the TV using the video cable (V).
22
Connect the Left and Right AUDIO OUT jacks from the VCR/DVD Recorder to the audio left/right in jacks from the TV using the audio cables (A).
S-Video connection
11
Connect the S-VIDEO OUT jack on the VCR/DVD Recorder to the S-Video in jack on the TV using the S-Video cable (S).
22
Connect the Left and Right AUDIO OUT jacks from the VCR/DVD Recorder to the audio left/right in jacks on the TV using the audio cables (A).
Component Video (Color Stream®) connection
11
Connect the COMPONENT VIDEO OUT jacks on the VCR/DVD Recorder to the corresponding in jacks on the TV using an Y Pb Pr cable (C).
22
Connect the Left and Right AUDIO OUT jacks from the VCR/DVD Recorder to the audio left/right in jacks on the TV using the audio cables (A).
Progressive Scan (ColorStream®pro) connection
If your television is a high-definition or “digital ready” television, you may take advantage of the VCR/DVD Recorder’s progressive scan output for the highest video resolution possible.
If your TV does not accept the Progressive Scan for­mat, the picture will appear scrambled if you try Progressive Scan on the VCR/DVD Recorder.
11
Connect the COMPONENT VIDEO OUT jacks on the VCR/DVD Recorder to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C).
22
Connect the Left and Right AUDIO OUT jacks from the VCR/DVD Recorder to the audio left/right in jacks on the TV using the supplied audio cables
(A).
otes
– Set Progressive Scan option to “ON” in the General
menu, see page 20.
– Progressive scan does not work with the analog video
connection (yellow VIDEO OUT jack).
Rear of TV
ANTENNA
INPUT
S-VIDEO
INPUT
VIDEO
INPUT
R
COMPONENT VIDEO INPUT
Pr
AUDIO INPUT
L
Y
Pb
S AV C
R
Rear of VCR/DVD Recorder
Connections (Continued)
16
Connecting to Optional Equipment
Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/ Pro Logic
Connect the Left and Right AUDIO OUT jacks on the VCR/DVD Recorder to the audio left and right in jacks on your amplifier, receiver, or stereo system, using the audio cables (A).
Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)
11
Connect one of the VCR/DVD Recorder’s DIGITAL AUDIO OUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.
22
You will need to activate the recorder’s digital out­put. (See “Audio” on page 21).
Digital Multi-channel sound
A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your VCR/DVD Recorder (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.
Caution:
Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.
otes
If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital con-
nection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder.
–To see the audio format of the current DVD in the on-
screen display, press AUDIO.
ote
This recorder does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs.
DIGITAL INPUT
Amplifier (Receiver)
Rear of VCR/DVD Recorder
A XO
R
OPTICAL
L
AUDIO INPUT DIGITAL INPUT
COAXIAL
DVR HOOKUP
17
Accessory Audio/Video (A/V) Connections to VCR/DVD Recorder
Connect the AV 1 or AV 2 jacks on the VCR/DVD Recorder to the audio/video out jacks on your accesso­ry component, using optional audio/video cables.
ote
If you use the S-V INPUT jack on the front panel, the signal of VIDEO OUT jack on the front panel is not out­put.
Connecting a Digital Camcorder
Using the front panel DV IN jack, it is possible to con­nect a DV digital camcorder or video deck or DVD-R/RW recorder and digitally transfer DV tapes or DVD-R/RW discs to DVD-R/RW.
Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder/video deck to the front panel DV IN jack of this recorder.
ote
This jack is for connection to DV equipment only. It is not compatible with digital satellite tuners or D-VHS video decks.
Connections (Continued)
Jack panel of Accessory Component 
(VCR, Camcorder, etc.)
S-VIDEO
OUTPUT
AUDIO OUTPUT
R
L
VIDEO OUTPUT
OR
DV Digital Camcorder
DV
IN/OUT
Rear of VCR/DVD Recorder
OR
Front of
VCR/DVD Recorder
Front of VCR/DVD Recorder
Loading...
+ 39 hidden pages