LG 71SA1DUA Users manual

Test Report No.: GETEC-E3-05-059 FCC Class B Certification
APPENDIX H
EUT Type: 71” LCoS Projection TV
FCC ID: BEJ71SA1DUA
LCoS Projection TV
OWNER’S MANUAL
MODELS: 62SA1D/71SA1D
62SA1D-UA/71SA1D-UA
LG Electronics U.S.A., Inc.
TM
R
TruSurround XT
Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service.
Model Number : Serial Number :
WARNING/CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi­cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appli­ance.
WARNING/CAUTION:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod­ification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-800-243-0000 http://www.lgusa.com
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
/CAUTION
W
W
arning/Caution
arning/Caution
Warning/Caution
LCoS Projection TV
TV Guide On Screen Notices for U.S.A.
TV Guide On Screen Notices for U.S.A.
Digital Cable Compatibility
Digital Cable Compatibility
This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable operator enhanced program (For example, electronic program guide provided by the cable operator), and data enhanced television service may require the use of a set top box. For more information contact your local cable operator.
In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc.
The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates.
Use of the CableCARD
TM
TradeMark.
“CableCARD
TM
is a trademark of Cable Television Laboratories, Inc.”
Trademark Notice
Aux Etats-Unis TV GUIDE et d’autres marques relatives sont des marques déposées de Gemstar-TV Guide International, Inc. et/ou d’une de ses sociétés affiliées. Au Canada TV GUIDE est une marque déposée de Transcontinental Inc., utilisée sous licence de Gemstar-TV Guide International, Inc.
Le système TV Guide On Screen est fabriqués sous licence de Gemstar-TV Guide International, Inc. et/ou d’une de ses sociétés
affiliées.
Le système TV Guide On Screen est protégés par un ou plusieurs brevets émis aux Etats-Unis, comme le 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
License Notice
Patent Notice
Owner’s Manual
Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appara­tus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be includ­ed where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illus­trates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-
fiers)that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Safety Instructions
Safety Instructions
PORTABLE CART WARNING
LCoS Projection TV
Safety Instructions
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.
15. CAUTION concerning the Power Cord :
Most appliances recommend they be placed upon a dedicated circuit; that
is, a single outlet circuit which powers only that appliance and has no
additional outlets or branch circuits. Check the specification page of
this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
16. Outdoor Use Marking :
WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.
17. Wet Location :
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall
be placed on the apparatus.
Owner’s Manual
Introduction
Introduction
Introduction
Controls
Controls
- This is a simplified representation of a front panel.
- Here shown may be somewhat different from your TV.
* To high quality of the
sound, do not press the speakers.
Front Panel Controls
Front Panel Controls
(북미)
POWER
TV GUIDE
POWER Button
TV GUIDE Button
MENU Button
ENTER Button
Function Status Indicators
Function Status Indicators
- Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal the operating status of the LCoS projection TV.
Off Power Cord is not connected.
Operation Indicator
Lamp Indicator
Temperature Indicator
Red Power Cord is connected, TV is in standby mode. Green TV turns on. Red (blinking) Power Cord is connected, TV is in booting sequence. White (Stacking) Preparing operation in standby mode. Orange Projection lamp is reaching the end of its life and needs to
Red (blinking) There is a problem with the lamp or around it. Contact an
Green (blinking) The lamp cover is not closed. Orange The projection TV is overheating. Check the blocked vents
Red The projection TV shuts down due to overheating. Red (blinking) The projection TV shuts down, check the cooling fan.
VOL CH
VOLUME ( Buttons
F,G)
CHANNEL (E, D) Buttons
On operating the
Operation Indicator/ Lamp Indicator/ Temperature Indicator
ENTER
be replaced with a new lamp. Contact your service center.
authorized service center.
of the Projection TV .
Contact your service center.
VOL CH
mode
ENTER
MENU
VOL CH
Owner’s Manual
Introduction
PC/DTV (XGA/ 480p/
720p 1080i)
DVI
RGB/DVI
UPGRADE PORT
/
P
R
P
B
Y
DTV/DVD
RGB
PC/DTV (XGA/ 480p/ 720p 1080i)
PC/DTV
(XGA /480p /720p
/1080i)
S-VIDEO
PR
PB
Y
MONO
CABLE
RGB INPUT
COMPONENT
INPUT2 INPUT1
DTV/DVD INPUT
RGB/DVI INPUT
(L)
(R)
AUDIO
(L)
(R)
AUDIO
VIDEO
(L)
(R)
AUDIO
(L)
(R)
AUDIO
MONITOR
OUTPUT
VIDEO
INPUT2
VIDEO
INPUT1
DIGITAL AUDIO OPTICAL INPUT1 (COMPONENT2)
DIGITAL AUDIO OPTICAL INPUT2
(DVI)
IEEE-1394
DIGITAL AUDIO
OPTICAL OUTPUT
ANTENNA
C a b
l e C A R D
HDMI1
/DVI
VARIABLE
AUDIO OUT
G-LINK
HDMI2
UPGRADE
PORT
ANTENNA Inputs
Connect antenna sig­nals to the TV directly.
DIGITAL AUDIO OPTICAL OUTPUT
Used to connect either an exter­nal amplifier, or add a sub­woofer to your surround sound system if it has a digital audio optical input. (Refer to )
MONITOR OUTPUT
Connect a second TV or Monitor.
S-VIDEO In
A connection available with some high-end equipment that provides even better picture qual­ity for Video 2.
RGB/DVI INPUT
Connect the monitor output connector from a PC to the appropri­ate input port.
RGB Input
Connect the TV output connector from a PC/DTV to the appropriate input port.
VARIABLE AUDIO OUT
Used to connect either an external amplifier, or add a sub-woofer to your surround sound system.
COMPONENT INPUT 1-2
Connect a component video/audio device to these jacks. Refer to your DVD manual for further information.
VIDEO 1 or 2
Connects the video sig­nals from various types of equipment.
Left/Right AUDIO
Used for stereo sound from various types of equipment.
IEEE1394
Connect DVHS or MicroMV to IEEE1394 Connector.
CableCARD™
Used for CableCARD received Cable Service Provider.
CABLE Inputs
Connect cable signals to the TV, either directly or through your cable box.
G-LINK
Connect a G-
LINK Cable to
this jack.
DIGITAL AUDIO OPTI­CAL INPUT1(COMPO­NENT2)
Connect digital audio from the equipment connected to COMPO­NENT 2.
DIGITAL AUDIO OPTI­CAL INPUT2(DVI)
Connect digital audio from the equipment connected to HDMI/DVI(VIDEO). (Refer to )
Notes: In standby mode, these port will not work.
If the video is connected through HDMI-TO-HDMI cable, you don’t need to connect digital audio. This port is used only when the video connected through DVI-TO-HDMI cable.
1
2
1
2
HDMI1/DVI, HDMI 2
Connect a HDMI signal to HDMI1/DVI or HDMI2. Or connect a DVI(Video) signal to HDMI1/DVI.
Back Connection Panel
Back Connection Panel
Connection Options
Connection Options
LCoS Projection TV
Introduction
LEFT/RIGHT AUDIO
Used for stereo sound from vari­ous types of equipment.
S-VIDEO
A connection available on some very high-end equipment that pro­vides better picture quality than video input.
VIDEO
Connects the video signals from any piece of equipment.
FRONT A/V
There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple.
The jacks are like those found on the back jack connec­tion panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be con­nected to the front connection panel.
To use the side jacks as the signal source, select them using Main Input menu as described on page 61. They will be named Front Video in the Main Input menu.
If you input both Front Video and S-Video, only the S-Video will work.
If youre connecting a video game device, make sure to change the picture settings with the EZ Picture option in the Video menu (see page 62).
Mini glossary
A/V CABLESAudio/Video cables. Three cable connectorRight audio (red), Left audio (white), and Video (yellow). A/V cables are
used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.
A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).
Front Connection Panel
Front Connection Panel
Owner’s Manual
Installation
<When the PC supports DVI>
How to connect
1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection.
2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI-
TALAUDIO(OPTICAL) port for DVI INPUT.
3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT
port located on the right side of RGB INPUT port.
How To Use
1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.
2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.61)
TV/VIDEO button is also available for this purpose.
3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC
mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
<When the PC supports RGB>
How to connect
1. Connect the PC to RGB INPUT port of this TV with a RGB cable(not supplied with this product).
2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT
port located on the right side of RGB INPUT port.
How To Use
1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz.
2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.61)
Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose.
3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC
mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
PC Setup
PC Setup
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.
Resolution
640x350
640x480
800x600
Horizontal
Frequency(KHz)
31.468
31.469
37.861
37.500
70.09
59.94
72.80
75.00
48.363
56.476
60.023
Vertical
Frequency(Hz)
1024x768
Monitor Display Specifications (RGB-PC or HDMI/DVI Mode)
35.156
37.879
48.077
46.875
56.25
60.31
72.18
75.00
60.00
70.06
75.02
LCoS Projection TV
Installation
Send the TVs audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.
2. Connect the other end of the optical cable to the digital audio (opti­cal) input on the audio equipment.
3. Set the
TV Speaker option - Off” in the AUDIO menu. Refer to
page 64. See the external audio equipment instruction manual for operation.
Caution: Do not look into the optical output port. Looking
at the laser beam may damage your vision.
Digital
Digital
Audio Output
Audio Output
PR
PB
Y
CABLE
COMPONENT
INPUT2 INPUT1
DTV/DVD INPUT
(L)
(R)
AUDIO
ANTENNA
DIGITAL AUDIO OPTICAL INPUT1 (COMPONENT2)
DIGITAL AUDIO OPTICAL INPUT2
(DVI)
IEEE-1394
DIGITAL AUDIO
OPTICAL OUTPUT
C A B L E C A R D
DVI
G-LINK
HDMI
HDMI1
/DVI
HDMI2
C a b
l e C A R D
Hook up Variable Audio Output, L-Audio-R to Amplifier system for Left/Right front speaker sound.
How to connect
1. Locate the Variable Audio Out jacks on the back of your TV and the Input jacks on the back of your stereo's amplifier.
2. Connect the two jacks, making sure that the right and left channels are connected correctly.
3. Set up your speakers through your analog stereo amplifier, accord­ing to the instructions provided with the amplifier.
External Stereo
External Stereo
PC/DTV
(XGA /480p /720p
/1080i)
S-VIDEO
MONO
RGB INPUT
RGB/DVI INPUT
(L)
(R)
AUDIO
(L)
(R)
AUDIO
VIDEO
(L)
(R)
AUDIO
MONITOR OUTPUT
VIDEO INPUT2
VIDEO INPUT1
VARIABLE
AUDIO OUT
UPGRADE
PORT
Owner’s Manual
Loading...
+ 24 hidden pages