LG Electronics 70LB7100, 60LB7100, 55LB7200 User Manual
OWNER’S MANUAL
LED TV*
* LG LED TVs are LCD TVs with LED backlighting.
Click! User Guide
Please read this manual carefully before operating your set and retain it
for future reference.
42LB6300
47LB6300
50LB6300
55LB6300
60LB6300
65LB6300
47LB6350
55LB6350
*MFL68027902*
42LB6500
47LB6500
50LB6500
55LB6500
60LB6500
60LB7100
65LB7100
70LB7100
P/NO : MFL68027902 (1406-REV04)
55LB7200
www.lg.com
2
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product.
Read these instructions.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
y
Clean only with a dry cloth.
y
ENGLISH
ENG
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may be
seriously injured or there is a possibility of accident
or death.
CAUTION
If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
WARNING
the State of California to cause cancer and birth defects
or other reproductive harm.
Wash hands after handling.
: This product contains chemicals known to
Do not block any ventilation openings. Install
y
in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such
y
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the
y
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet (Can differ by country).
IMPORTANT SAFETY INSTRUCTIONS
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
3
Do not press strongly upon the panel with a hand
y
or a sharp object such as a nail, pencil or pen, or
make a scratch on it.
Protect the power cord from being walked on
y
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
y
the manufacturer.
Use only with a cart, stand, tripod, bracket, or
y
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or
y
when unused for long periods of time.
Keep the packing anti-moisture material or vinyl
y
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit
the nearest hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of the reach of
children.
CAUTION concerning the Power Cord
y
(Can differ by country):
It is recommended that appliances be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner’s
manual to be certain. Do not connect too many
appliances to the same AC power outlet as
this could result in fire or electric shock. Do not
overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized service. Protect the power
cord from physical or mechanical abuse, such
as being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord
exits the appliance. Do not move the TV with the
power cord plugged in. Do not use a damaged
or loose power cord. Be sure do grasp the plug
when unplugging the power cord. Do not pull on
the power cord to unplug the TV.
ENGENGLISH
Refer all servicing to qualified service personnel.
y
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Do not stick metal objects or any other
y
conductive material into the power cord. Do
not touch the end of the power cord while it is
plugged in.
- To reduce the risk of fire or electrical
Warning
y
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product near
flammable objects such as gasoline or candles, or
expose the TV to direct air conditioning.
4
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
ENG
Do not expose to dripping or splashing and do
y
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g. on
shelves above the unit).
Grounding
y
(Except for devices which are not grounded.)
Ensure that you connect the earth ground wire to
prevent possible electric shock (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grounded AC outlet). If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not
try to ground the unit by connecting it to telephone
wires, lightning rods, or gas pipes.
Short-circuit
Breaker
As long as this unit is connected to the AC wall
y
Power Supply
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
Do not attempt to modify this product in any way
y
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
Outdoor Antenna Grounding
y
(Can differ by country):
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power circuits,
or where it can come in contact with such power
lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges. Section 810 of the
National Electrical Code (NEC) in the U.S.A. provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Antenna Lead in Wire
Ground Clamp
Electric Service
Equipment
Ground Clamp
Cleaning
y
NEC: National Electrical Code
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
When cleaning, unplug the power cord and wipe
gently with a soft cloth to prevent scratching. Do
not spray water or other liquids directly on the TV
as electric shock may occur. Do not clean with
chemicals such as alcohol, thinners or benzine.
Moving
y
Make sure the product is turned off, unplugged and
all cables have been removed. It may take 2 or more
people to carry larger TVs. Do not press or put stress
on the front panel of the TV.
Ventilation
y
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other materials
while plugged. Do not install in excessively dusty
places.
If you smell smoke or other odors coming from the
y
TV, unplug the power cord and contact an authorized
service center.
Keep the product away from direct sunlight.
y
Never touch this apparatus or antenna during a
y
thunder or lightning storm.
When mounting a TV on the wall, make sure not to
y
install the TV by hanging the power and signal cables
on the back of the TV.
Do not allow an impact shock or any objects to fall
y
into the product, and do not drop anything onto the
screen.
Disconnecting the Main Power
y
The power outlet used with this device must remain
easily accessible.
Store the accessories (battery, etc.) in a safe location
y
out of the reach of children.
This apparatus use batteries. In your community
y
there might be regulations that require you to dispose
of these batteries properly due to environmental
considerations. Please contact your local authorities
for disposal or recycling information.
Do not dispose of batteries in a fire.
y
Do not short circuit, disassemble or allow the
y
batteries to overheat.
Dot Defect
y
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
Generated Sound
y
Cracking noise
watching or turning off the TV is generated by plastic
thermal contraction due to temperature and humidity.
This noise is common for products where thermal
deformation is required.
Electrical circuit humming/panel buzzing
noise is generated from a high-speed switching
circuit, which supplies a large amount of current
to operate a product. It varies depending upon the
product.
This generated sound does not affect the
performance and reliability of the product.
Take care not to touch the ventilation openings.
y
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or cause
defects in the product.
Do not install this product on a wall if it could be
y
exposed to oil or oil mist. This may damage the
product and cause it to fall.
If the TV feels cold to the touch, there may be a small
y
flicker when it is turned on. This is normal, there is
nothing wrong with TV. Some minute dot defects
may be visible on the screen, appearing as tiny red,
green, or blue spots. However, they have no adverse
effect on the TV’s performance. Avoid touching the
LCD screen or holding your finger(s) against it for
long periods of time. Doing so may produce some
temporary distortion effects on the screen.
A cracking noise that occurs when
A low level
Preventing Image burn or Burn-in on
your TV screen
IMPORTANT SAFETY INSTRUCTIONS
For USA and Canada
FCC NOTICE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
5
ENGENGLISH
If a fixed image displays on the TV screen for a long
y
period of time, it will be imprinted and become
a permanent disfigurement on the screen. This
is image burn or burn-in and not covered by the
warranty.
If the aspect ratio of the TV is set to 4:3 for a long
y
period of time, image burn may occur on the
letterboxed area of the screen.
Avoid displaying a fixed image on the TV screen for
y
a long period of time (2 or more hours for LCD, 1
or more hours for the Plasma TV) to prevent image
burn.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected
to the grounding system of the building, as close
to the point of the cable entry as practical.
6
IMPORTANT SAFETY INSTRUCTIONS
Viewing 3D Imaging
(For 3D models)
WARNING
Viewing Environment
Viewing Time
y
-
When watching 3D contents, take 5 to
15 minute breaks every hour. Viewing 3D
contents for a long period of time may cause
headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
Some users may experience a seizure or
y
other abnormal symptoms when they are
exposed to a flashing light or particular
pattern from 3D contents.
Do not watch 3D videos if you feel nausea,
y
ENGLISH
ENG
are pregnant and/ or have a chronic illness
such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
3D Contents are not recommended to
y
those who suffer from stereo blindness
or stereo anomaly. Double images or
discomfort in viewing may be experienced.
If you have strabismus (cross-eyed),
y
amblyopia (weak eyesight) or astigmatism,
you may have trouble sensing depth and
easily feel fatigue due to double images. It
is advised to take frequent breaks than the
average adult.
If your eyesight varies between your right
y
and left eye, revise your eyesight prior to
watching 3D contents.
CAUTION
Viewing Environment
Viewing Distance
y
-
Maintain a distance of at least twice the
screen diagonal length when watching 3D
contents. If you feel discomfort in viewing
3D contents, move further away from the TV.
Viewing Age
Infants / Children
y
- Usage/ Viewing 3D contents for children
under the age of 5 are prohibited.
- Children under the age of 10 may overreact
and become overly excited because their
vision is in development (for example: trying
to touch the screen or trying to jump into
it. Special monitoring and extra attention is
required for children watching 3D contents.
- Children have greater binocular disparity of
3D presentations than adults because the
distance between the eyes is shorter than
one of adults. Therefore they will perceive
more stereoscopic depth compared to
adults for the same 3D image.
Teenagers
y
- Teenagers under the age of 19 may be
stimulated to light coming from 3D videos.
Advise them not to watch 3D videos for a
long time when they are tired.
Elderly
y
- The elderly may perceive less of a 3D
effect than the youth. Do not sit closer to
the TV than the recommended distance.
Cautions when using the 3D glasses
Symptoms which require discontinuation or
refraining from watching 3D contents
Do not watch 3D contents when you feel
y
fatigue from lack of sleep, overwork or
drinking.
When these symptoms are experienced,
y
stop using/watching 3D contents and get
enough rest until the symptom subsides.
- Consult your doctor when the symptoms
persist. Symptoms may include headache,
eyeball pain, dizziness, nausea, palpitation,
blurriness, discomfort, double image,
visual inconvenience or fatigue.
Make sure to use LG 3D glasses.
y
Otherwise, you may not be able to view 3D
videos properly.
Do not use 3D glasses instead of your
y
normal glasses, sunglasses or protective
goggles.
Using modified 3D glasses may cause eye
y
strain or image distortion.
Do not keep your 3D glasses in extremely
y
high or low temperatures. It will cause
deformation.
The 3D glasses are fragile and are easy to be
y
scratched. Always use a soft, clean piece of
cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp
objects or clean/wipe them with chemicals.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model.
For more information about licenses, visit
www.lg.com
.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained
in this product, please visit
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the
cost of performing such distribution (such as the cost of media, shipping and handling) upon email
request to
purchased the product.
opensource@lge.com
http://opensource.lge.com
. This offer is valid for three (3) years from the date on which you
.
7
ENGENGLISH
8
TABLE OF CONTENTS
TABLE OF CONTENTS
2 IMPORTANT SAFETY
INSTRUCTIONS
6 Viewing 3D Imaging
(For 3D models)
7 LICENSES
7 OPEN SOURCE SOFTWARE
NOTICE
8 TABLE OF CONTENTS
9 INSTALLATION PROCEDURE
9 ASSEMBLING AND PREPARING
ENGLISH
ENG
9 Unpacking
11 Optional Extras
12 Parts and Buttons
13 - Using the Joystick button
14 Lifting and Moving the TV
15 Setting Up the TV
15 - Attaching the Stand
17 - Mounting on a Table
18 - Tidying Cables
19 - Mounting on a Wall
31 MAGIC REMOTE FUNCTIONS
32 Registering Magic Remote
32 How to use Magic Remote
32 Precautions to Take when Using the
Magic Remote
33 USING THE USER GUIDE
34 SPECIFICATIONS
37 EXTERNAL CONTROL DEVICE
SETUP
38 MAINTENANCE
38 Cleaning Your TV
38 - Screen, Frame, Cabinet, and Stand
38 - Power Cord
38 TROUBLESHOOTING
21 MAKING CONNECTIONS
21 Connecting to an Antenna or Cable
22 Connecting to a HD receiver, DVD Player,
or VCR
22 - HDMI Connection
23 - DVI to HDMI Connection
24 - Connecting to a mobile phone
25 - Component Connection
26 - Composite Connection
27 Connecting to a PC
27 - HDMI Connection or DVI to HDMI
Connection
29 Connecting to an Audio System
29 - Digital Optical Audio Connection
30 Connecting a USB Drive
NOTE
Image shown may differ from your TV.
y
Your TV’s OSD (On Screen Display) may
y
differ slightly from that shown in this
manual.
The available menus and options may
y
differ from the input source or product
model that you are using.
New features may be added to this TV in
y
the future.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
INSTALLATION PROCEDURE
Open the package and make sure all the accessories are included.
1
Attach the stand to the TV set.
2
Connect an external device to the TV set.
3
Make sure the network connection is available.
4
You can use the TV network functions only when the network connection is made.
* When the TV is turned on for the first time after being shipped from the factory, initialization of
the TV may take up to one minute.
ASSEMBLING AND PREPARING
Unpacking
9
Check your product box for the following items. If there are any missing accessories, contact the
local dealer where you purchased your product. The illustrations in this manual may differ from the
actual product and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
y
Any damages or injuries by using unapproved items are not covered by the warranty.
y
In case of some model, the thin film on screen is a part of TV, So don’t take it off.
y
NOTE
The items supplied with your product may vary depending upon the model.
y
Product specifications or contents of this manual may be changed without prior notice due to
y
upgrade of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
y
(0.39 inches) thick and 18 mm (0.7 inches) width.
Use an extension cable that supports USB 2.0 if the USB cable or USB FLASH DRIVE does not
y
fit into your TV’s USB port.
B
A
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
B
A
ENGENGLISH
10
ASSEMBLING AND PREPARING
Magic Remote,
Batteries (AA)
(See page 31.)
Tag On
Tag On
(Depending upon model)
ENGLISH
ENG
Cable Holder
(Depending upon model)
(See page 18.)
(For 42/47/50/55LB6300,
47/55LB6350,
42/47/50/55LB6500)
Owner’s Manual
(For 42LB6300, 42LB6500)
Wall Mount Spacer
2 EA
(See page 20.)
Cable Management
2 EA
(See page 18.)
(For 60/65LB6300,
60LB6500,
60/65/70LB7100,
55LB7200)
Power Cord
(Depending upon model)
Stand Screws
4 EA, M4 x L14
(See page 15, 16.)
(For LB6500, LB7100
series, 55LB7200)
Cinema 3D Glasses
The number of 3D glasses
may differ depending upon
the model or country.
Stand Base
(See page 16.)
Stand Base/Stand Body
(See page 15.)
ASSEMBLING AND PREPARING
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
These devices only work with certain models.
The model name or design may be changed manufacturer’s circumstances or policies.
11
AN-MR500
Magic Remote
AG-F***DP
Dual Play Glasses
(Depending upon model)
AG-F***
Cinema 3D Glasses
(Depending upon model)
LG Audio Device Tag On
AN-VC5**
Video Call Camera
ENGENGLISH
12
ASSEMBLING AND PREPARING
Parts and Buttons
(For 42/47/50/55LB6300, 47/55LB6350,
42/47/50/55LB6500)
Screen
Speakers
Remote Control Sensor and
Intelligent Sensor
Power Indicator
ENGLISH
(For 60/65LB6300, 60LB6500,
ENG
60/65/70LB7100)
Screen
Joystick Button
1
Joystick Button
(For 55LB7200)
Screen
2
Speakers
Remote Control Sensor and
Intelligent Sensor
Joystick Button
1
2
Power Indicator
2
Speakers
Remote Control Sensor and
Intelligent Sensor
1
Power Indicator
1
Intelligent sensor - Adjusts the image quality and brightness based on the surrounding
environment.
2
Joystick button is located below the screen of TV.
NOTE
Removing the protective film on the bottom of the TV
y
(Depending upon model)
»
The protective film was applied to the TV face to protect it from
scratches and other damage during shipping.
»
When the TV is installed, peel the film off the bottom of the
cabinet.
Loading...