LG 60UJ634V-ZD, 65UJ634V-ZD Schematic

CONFIDENTIAL

LED TV

SERVICE MANUAL

CHASSIS : UD74Q

MODEL : 60UJ634V 60UJ634V-ZD

65UJ634V 65UJ634V-ZD

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL69832206 (1703-REV00)

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS .................................................................... 4

SPECIFICATION ....................................................................................... 6

SOFTWARE UPDATE .............................................................................. 11

BLOCK DIAGRAM ..................................................................................12

EXPLODED VIEW .................................................................................. 25

DISASSEMBLY GUIDE .......................................................................... 26

TROUBLE SHOOTING GUIDE ................................................ APPENDIX

- 2 -

SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

- 3 -

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug

or other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specied otherwise in this service manual, clean

electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength)

CAUTION: This is a ammable mixture. Unless specied otherwise in this service manual, lubrication

of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this

service manual.

CAUTION: Do not connect the test xture ground strap to any

heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some eld-effect transistors

and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some sol-

der removal devices not classied as “anti-static” can generate electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your

foot from a carpeted oor can generate static electricity sufcient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand

against the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder ows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 4 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

- 5 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

.

1. Application range

This specification is applied to the LED TV with UD74Q chassis.

2. Requirement for Test

Each part is tested as below without special appointment. (1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C (2) Relative Humidity: 65 % ± 10 % (3) Power Voltage

: Standard input voltage (AC 100~240 V, 50/60 Hz) * Standard Voltage of each products is marked by models.

(4) Specification and performance of each parts are followed

each drawing and specification by part number in accordance with BOM.

(5) The receiver must be operated for about 20 minutes prior

to the adjustment.

3. Test method

(1) Performance: LGE TV test method followed (2) Demanded other specification

- Safety : CE, IEC specification

- EMC : CE, IEC specification

- Wireless : Wireless HD Specification (Option)

4. Model General Specification

No. Item Specication Remarks

DTV & Analog (Total 37 countries)

DTV (MPEG2/4, DVB-T) : 26 countrie

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, , Belgium, Luxemburg, Greece, Czech, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Slovakia, Belarus

1 Market EU/CIS(PAL Market-37Countries)

DTV (MPEG2/4, DVB-T2) :11 countries

UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan, Russia, Italy, Croatia, Serbia

DTV (MPEG2/4, DVB-C) : 37 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Belarus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan

DTV (MPEG2/4,DVB-S) : 37 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain,Belgium, Luxemburg, Greece, Czech, Turkey, Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Slovakia, Belarus, UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan,Russia, Italy, Croatia, Serbia

Supported satellite : 35 satellites

ABS1 75.0E , AMOS 4.0W , ASIASAT3S 105.5E , ASTRA 19.2E , ASTRA

23.5E , ASTRA 28.2E , ASTRA 4.8E, ATLANTIC BIRD2 8.0W , ATLANTIC BIRD3 5.0W , BADR 26.0E , DIRECTV-1R 56.0E , EUROBIRD 9A 9.0E , EUROBIRD3 33.0E , EUTELSAT 36 A/B 36.0E , EUTELSAT W2A 10.0E , EUTELSAT W3A 7.0E , EUTELSAT7WA 7.3W

- 6 -

No. Item Specication Remarks

2 Broadcasting system

3 Program coverage

4 Receiving system

1)PAL/SECAM B/G/I/D/K SECAM L/L’

2)DVB-T/T2, C, S/S2

1 ) Digital TV

-VHF, UHF

-C-Band, Ku-Band

2) Analogue TV

-VHF : E2 to E12

-UHF : E21 to E69

-CATV : S1 to S20

-HYPER : S21 to S47

Analog : Upper Heterodyne Digital : COFDM, QAM

► DVB-T

- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32

- Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

► DVB-T2

- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,

- Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

5 Input Voltage AC 100 ~ 240V 50/60Hz

► DVB-C

- Symbolrate :

4.0Msymbols/s to 7.2Msymbols/s

- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

► DVB-S/S2

- Symbolrate DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s DVB-S (QPSK) : 2 ~ 45Msymbol/s

- 9 iterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10

- 7 -

5. External Input Format

5.1. 2D Mode

5.1.1. Component input(Y, CB/PB, CR/PR)

No Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed

1 720*480 15.73 59.94 13.50 SDTV ,DVD 480i

2 720*480 15.75 60.00 13.5135 SDTV ,DVD 480i

3 720*576 15.62 50.00 13.50 SDTV 576i

4 720*480 31.47 59.94 27.00 SDTV 480p

5 720*480 31.50 60.00 27.027 SDTV 480p

6 720*576 31.25 50.00 27.00 SDTV 576p

7 1280*720 44.96 59.94 74.175 HDTV 720p

8 1280*720 45.00 60.00 74.250 HDTV 720p

9 1280*720 37.50 50.00 74.250 HDTV 720p

10 1920*1080 28.12 50.00 74.250 HDTV 1080i

11 1920*1080 33.72 59.94 74.175 HDTV 1080i

12 1920*1080 33.75 60.00 74.250 HDTV 1080i

13 1920*1080 56.25 50.00 148.50 HDTV 1080p

14 1920*1080 67.43 59.94 148.350 HDTV 1080p

15 1920*1080 67.50 60.00 148.50 HDTV 1080p

5.1.2. HDMI Input (PC)

No Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed Remarks

1 640*350 31.46 70.09 25.17 EGA

2 720*400 31.46 70.08 28.32 DOS

3 640*480 31.46 59.94 25.17 VESA(VGA)

4 800*600 37.87 60.31 40.00 VESA(SVGA)

5 1024*768 48.36 60.00 65.00 VESA(XGA)

6 1152*864 54.34 60.05 80.00 VESA

7 1360*768 47.71 60.01 85.00 VESA(WXGA)

8 1280*1024 63.98 60.02 109.00 VESA(SXGA) FHD, UHD only

9 1920*1080 67.50 60.00 158.40 WUXGA(CEA 861D) FHD, UHD only

10 3840*2160 54.00 24.00 297.00 UDTV 2160P UHD only

11 3840*2160 56.25 25.00 297.00 UDTV 2160P UHD only

12 3840*2160 67.50 30.00 297.00 UDTV 2160P UHD only

13 4096*2160 53.95 23.97 296.703 UDTV 2160P UHD only

14 4096*2160 54.00 24.00 297.00 UDTV 2160P UHD only

- 8 -

5.1.3. HDMI Input (DTV)

No Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed Remarks

1 640*480 31.46 59.94 25.13 SDTV 480P

2 640*480 31.50 60.00 25.13 SDTV 480P

3 720*480 15.73 59.94 13.50 SDTV, DVD 480I(525I)

Spec. out but display4 720*480 15.75 60.00 13.51 SDTV, DVD 480I(525I)

5 720*576 15.62 50.00 13.50 SDTV, DVD 576I(625I) 50Hz

6 720*480 31.47 59.94 27.00 SDTV 480P

7 720*480 31.50 60.00 27.03 SDTV 480P

8 720*576 31.25 50.00 27.00 SDTV 576P

9 1280*720 44.96 59.94 74.18 HDTV 720P

10 1280*720 45.00 60.00 74.25 HDTV 720P

11 1280*720 37.50 50.00 74.25 HDTV 720P

12 1920*1080 28.12 50.00 74.25 HDTV 1080I

13 1920*1080 33.72 59.94 74.18 HDTV 1080I

14 1920*1080 33.75 60.00 74.25 HDTV 1080I

15 1920*1080 26.97 23.97 63.30 HDTV 1080P

16 1920*1080 27.00 24.00 63.36 HDTV 1080P

17 1920*1080 33.71 29.97 79.12 HDTV 1080P

18 1920*1080 33.75 30.00 79.20 HDTV 1080P

19 1920*1080 56.25 50.00 148.50 HDTV 1080P

20 1920*1080 67.43 59.94 148.35 HDTV 1080P

21 1920*1080 67.50 60.00 148.50 HDTV 1080P

22 3840*2160 53.95 23.98 297.00 UDTV 2160P UHD only

23 3840*2160 54.00 24.00 297.00 UDTV 2160P UHD only

24 3840*2160 56.25 25.00 297.00 UDTV 2160P UHD only

25 3840*2160 61.43 29.97 297.00 UDTV 2160P UHD only

26 3840*2160 67.50 30.00 297.00 UDTV 2160P UHD only

27 3840*2160 112.50 50.00 594.00 UDTV 2160P(DVB) UHD only

28 3840*2160 134.86 59.94 593.41 UDTV 2160P UHD only

29 3840*2160 135.00 60.00 594.00 UDTV 2160P UHD only

30 4096*2160 53.95 23.98 297.00 UDTV 2160P UHD only

31 4096*2160 54.00 24.00 297.00 UDTV 2160P UHD only

32 4096*2160 56.25 25.00 297.00 UDTV 2160P UHD only

33 4096*2160 61.43 29.97 297.00 UDTV 2160P UHD only

34 4096*2160 67.50 30.00 297.00 UDTV 2160P UHD only

35 4096*2160 112.50 50.00 594.00 UDTV 2160P(DVB) UHD only

36 4096*2160 134.86 59.94 593.41 UDTV 2160P UHD only

37 4096*2160 135.00 60.00 594.00 UDTV 2160P UHD only

- 9 -

5.2. 3D Mode - DTV/HDMI/USB

5.2.1. RF Input

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1 1280*720 37.50 50 74.25 HDTV 720P

2 1920*1080 28.13 50 74.25 HDTV 1080I

2D to 3D, Side by Side, Top & Bottom

- 10 -

SOFTWARE UPDATE

1. USB

(1) Insert the USB memory Stick to the USB port. (2) Automatically detect the SW Version and show the below

message

(3) Click [YES]: initiate the download and install of the update.

(4) Click [Check Now]: move to “About This TV” page for

update.

(5) TV is updating.

2. NSU

(1) Menu -> All Settings -> General -> About This TV

(2) Click [CHEK FOR UPDATES] : system check newest

version

(3) Click [DOWNLOAD AND INSTALL] (4) TV is updating

(6) After finished the update, below Pop-up appear.

(7) Click [Yes] : TV will be DC OFF -> ON (8) After TV turned on, Check the updated SW Version and

Tool Option.

- 11 -

(5) After finished the update, below Pop-up appear

(6) Turn OFF the TV and On. Check the updated SW Version

and Tool Option

Realtek

K3Lp

DDR3 2133 X 32

(512MB X 2EA)

Hynix 20nm

DDR3 2133 X 32

(512MB X 2EA)

eMMC (4GB)

Toshiba 15nm

CI Slot

B-CAS

(JAPAN)

B-CAS

controller

SMARTCARD_I/F

USB2 (2.0)

OCP

USB3 (2.0)

HDMI3

HDMI2(ARC)

HDMI1

Air/

Cable

DVB-S

LNB

(DT1805)

REAR(H)

P_TS_OUT

P_TS_IN

Sub Micom

(RENESAS

R5F100GEAFB)

X_TAL

32.768KHz

I2C 1

USB_WIFI

X_TAL

27MHz

Sub Assy

LAN

ETHERNET

SPDIF

A

V/COMP

CVBS/YPbPr

SPDIF OUT

H/P

AMP

RS-232

MAX323

MAIN Audio AMP

(DTA2010M)

I2S Out

I2C 4

Vx1 51P (8 lane) : LGD 60/65/70/75

Vx1 / EPI

I2C 6

EPI PMIC

(SW50B3A)

Level

shifter

M0 M1

B-CAS

I2C 6

NVRAM (256Kb)

I2C 4

I2C 2

EPI block

HDMI4 (EEPROM)

USB1 (3.0)

OCP

K3L only

IR / KEY(1Key)

LOGO LIGHT(Ready)

WIFI/BT Combo

MTK IC

EPI 60Px2 (3G, 6 lane) : LGD 43/49/55

CEDS 68Px2 (1.5G, 12 lane) : BOE

T2/C/S2 NIM tuner

TS

RF IC

Demode

(T/C/S/T2/S2)

BLOCK DIAGRAM

1. K3Lp Block Diagram (External)

HDMI 6G 4

K3L only. (K3Lp 256MB x 2ea SoC )

- 12 -

2. K3Lp Block Diagram (Internal)

- 13 -

K3L

I2C_SCL6/SDA6

Vx1 8Lane 51P

/A/

A

HTPDAn

Panel

3840x2160@120p

[EPI_TX0~EPI_TX15]

BIT[2/1/0] UD_V x 1 Lane

0/0/0 4K@120P(16Lanes)

0/0/1 4K@60P(8Lanes)

0/1/0 5K@120P(20Lanes)

0/1/1 OLED ULTRA HD

1/0/0 FHD@120 (4Lane)

1/0/1 FHD@60 (4Lane)

1/1/0 Reserved

1/1/1 Reserved

A

LOCKAn

/

A

DATA_FORMAT_0/1

[GPIO08_DATA_FORMAT_0]

Vx1 8Lane 41P

HW Option TBD

[EPI_TX0~EPI_TX15]

[GPIO_2_TCON_SCL/TCON_9]

[GPIO_1_TCON_SDA/TCON_

5]

[GPIO_5_VBY_LOCK/EPLOCK]

[GPIO_4_VBY_HTPD/TCON_14]

[GPIO09_DATA_FORMAT_1]

AGP_CTL

A

VX1_MSE

3.Vx1 Block Diagram

- 14 -

17Y Tuner

K3Lp

RTK

[B1_+3.3V_RF] 3

[+3.3V_DEMOD_TU] 11

[B3_+1.2V_DEMOD] 13

[IF_P_TU] 8

[IF_N_TU] 7

[TU_SIF] 6

[TU_CVBS_TU] 4

[IF_AGC_TU] 5

[M_ERROR] 14

[M_MCLK] 15

[M_SYNC] 16

[M_VALID] 17

AB5 / AB2 [GPIO57_TP0_CLK]

AB6 / AA3 [GPIO56_TP0_SYC]

AB4 / AC2 [GPIO58_TP0_VAL]

FE_DEMOD1_TS_ERROR

FE_DEMOD1_TS_CLK

FE_DEMOD1_TS_SYNC

FE_DEMOD1_TS_VAL

FE_DEMOD1_TS_DATA[0-7] 18-25

FE_DEMOD1_TS_DATA [0-7]

[GPIO59~66_TP0_D0~TP0_D7]

[B4_+2.5V_DEMOD] 29

+2.5V_Normal

[/TU_RESET1_TU] 10

/TU_RESET1

AB2 / L1 [VINRP_TUNER0_REST]

[LNB_TX1] 12

[LNB] 26(Full NIM) / [LNB] 26(Half NIM)

[SCL_RF] 1

[SDA_RF] 2

I2C_SCL2

I2C_SDA2

+3.3V_NORMAL

IF_P

IF_N

TUNER_SIF (OPT : TU_EXT_ATV)

TU_CVBS (OPT : TU_EXT_ATV)

IF_AGC

AE1 / U2 [IF_P]

AE2 / U3 [IF_N]

AE3 / V2 [SIF]

Y5 / R5 [VIN10P]

Y4 / W4 [GPIO55_RF_IF_AGC1]

[SCL_DEMOD] 36

[SDA_DEMOD] 35

+ DEMOD_CORE

LNB

IC7001

DT1805

LNB_TX

LNB_OUT

1.8K ȳ

5 [SCL]

6 [SDA]

8 [TONECTRL]

2 [LNB]

33 ȳ

[/TU_RESET2_TU] 34

/TU_RESET2

AA3 / M2 [VINGP_DEMOD_RESET]

33 ȳ

TU_JP

AA5 / Y4 [GPIO52_TUNER0_SCL]

AA6 / AA4 [GPIO51_TUNER0_SDA]

[S_ERROR] 28

[S_MCLK] 33

[S_SYNC]30

[S_VAL] 31

[S_DATA]32

TU_JAPAN

AF4 [GPIO54_TUNER1_SCL]

AF5 [GPIO53_TUNER1_SDA]

Reserved for Dual Tuner_only K3L

F

G

_T

R

1

_

5

_

R

1

_

R

e

f

l

r

_

y

K

3

L

AF3 / W2 [IP_1]

AG1 / W3 [IN_1]

AG2 / Y2 [QP_2]

AG3 / Y3 [QN_2]

IF_S_IP

IF_S_IN

IF_S_QP

IF_S_QN

[IF_S_IP_MAIN] 59

[IF_S_IN_MAIN] 60

[IF_S_QP_MAIN] 62

[IF_S_QN_MAIN] 61

JAPAN_OPT

FE_DEMOD1_TS_1_DATA[1]

FE_DEMOD1_TS_1_DATA[4]

FE_DEMOD1_TS_1_DATA[3]

FE_DEMOD1_TS_1_DATA[2]

FE_DEMOD2_TS_ERROR

4. Tuner

- 15 -

HDMI_ARC

ST_GPIO_23_H0_ARC[AG13]

[V2] SIF

I2C_SDA/SCL_AMP

AUD_SCK

AMP_RESET_N

HP_L/ROUT

H/P Jack

SIDE_HP_MUTE

GPIO021_SCLK[C2]

GPO_0_I2S_WCLK/SPDIF_OUT_1[D13]

GPIO15_D0 [B3]

GPIO_35_HPOL [N5]

GPIO_36_HPOR [N4]

TU_SIF

AI2R_AMP_SDA [G4]

AI3L_AMP_SCL [G5]

H/P AMP

TPA6138A2

(IC6300)

LPF

AI2L_AMP_RESET_N [F5]

SPDIF_OUT

AV1_CVBS_DET

COMP1/AV1/DVI_L_IN

COMP1/AV1/DVI_R_IN

[H5] AIO1L_AV1_CVBS_DET

[M5] AI1L

[M4] AI1R

HP_LOUT_AMP

HP_ROUT_AMP

LPF

Realtek

K3Lp

Tuner

GPIO_6_SPDIF_OUT_0 [E3]

AUD_LRCH

AUD_LRCK

AMP_MUTE

SPK_R+ / R-

SPK_L+ / L-

MAIN AMP

DTA2010M

(IC5800)

MICOM

SPK L

SPK R

22

26

[38] CLK_I [8] WCK [7] SDATA [10,11] [36] [12]

[30, 33]

[18, 21]

AV/COMP

HDMI2

SPDIF

HP_DET

AIO2L_HP_DET[J5]

COMP1_Pb

COMP1_Pr

COMP1_Y/CVBS

COMP1_DET

[N3] VIN 3P

[P3] VIN 5P

[P2] VIN 4P

[H4] AI3R_COMP1_DET

5. Video & Audio IN/OUT

- 16 -

REALTEK

K3Lp

HDMI2.0_1_HPD

TMDS1 - D0/D1/D2/CLK

ST_GPIO_19_5V_DET_HDMI_0

ST_GPIO_18_H0_HPD

ST_GPIO_21_H0_SCL

ST_GPIO_20_H0_SDA

P0_CKN/P_RGB_N/P

DDC_SCL1 / DDC_SDA1

MICOM

R5F100GEAFB

(IC3000)

HDMI2.0_1_5V_DET

HDMI2.0_2_HPD

TMDS2 - D0/D1/D2/CLK

ST_GPIO_15_5V_DET_HDMI_1

ST_GPIO_14_H1_HPD

ST_GPIO_17_H1_SCL

ST_GPIO_16_H1_SDA

ST_GPIO_23_H0_ARC

P1_CKN/P_RGB_N/P

DDC_SCL2 / DDC_SDA2

HDMI2.0_2_5V_DET

HDMI2.0_3_HPD

TMDS3 - D0/D1/D2/CLK

ST_GPIO_10_5V_DET_HDMI_2

ST_GPIO_11_H2_HPD

ST_GPIO_13_H2_SCL

ST_GPIO_12_H2_SDA

P2_CKN/P_RGB_N/P

DDC_SCL3 / DDC_SDA3

HDMI2.0_3_5V_DET

HDMI2.0_4_HPD

TMDS4 - D0/D1/D2/CLK

ST_GPIO_07_5V_DET_HDMI_3

ST_GPIO_06_H3_HPD

ST_GPIO_09_H3_SCL

ST_GPIO_08_H3_SDA

P3_CKN/P_RGB_N/P

DDC_SCL4 / DDC_SDA4

HDMI2.0_4_5V_DET

HDMI2 with ARC

HDMI1

HDMI3

HDMI4

HDMI_CEC

HDMI_ARC

HDMI_CEC

6. HDMI 2.0 Block

- 17 -

RS232C

(IC7200)

WIFI_DM / DP

SOC_RX / TX

USB2.0_2_DM / DP

USB2

DEBUG_RX / TX

Realtek

K3Lp

HSDM1[AM24]

HSDP1[AL24]

HSDM2[AM25]

HSDP2[AL25]

HSDM0 [G1]

HSDP0 [G2]

USB1

USB2.0_3_DM / DP

MICOM

R5F100GEAFB

(IC3000)

[AH5] ST_GPIO_02_VGA_SDA

[AG5] ST_GPIO_01_VGA_SCL

ST_GPIO_25_UART0/1[AH13]

ST_GPIO_24_UART0/1[AG14]

Wafer

(P200)

Wafer

(P4000)

DEBUG UART

Wafer

(P201)

5 7 9

10

19

20

23

24

SOC_RX / TX

DCDC OCP

BD2242G

(IC4501)

USB_OCD2 [AJ18]

USB_CTL2 [AG20]

+5V_USB2.0_2

+5V_USB2.0_3

WOL/WIFI_POWER_ON

BT_RESET

BT_WAKEUP_DEVICE

BT_WAKEUP_HOST

IR

LED_R

KEY2

KEY1

DCDC OCP

BD2242G

(IC4700)

USB_OCD3 [AG22]

USB_CTL3 [AH19]

DOUT1

RIN1

PHONE JACK

7. USB / WIFI / M-REMOTE / UART(Debug)

- 18 -

[GPIO_2_TCON_SCL/TC

ON_9]

I2C_SDA6

SW50B3A(LGD)

SW5253A(BOE)

EPI PMIC

I2C_SCL6

1.8k ȳ

[ST_GPIO_26_MICRO_SDA]

[ST_GPIO_27_MICRO_SCL]

I2C_SDA_1

I2C_SCL_1

K3Lp

[GPIO_1_TCON_SDA/TC

ON_5]

1.8k ȳ

+3.3V_NOR

1.8k ȳ

+3.5V_ST

R5F100GEAFB#30

MICOM

[AI3L_AMP_SCL]

[AI2R_AMP_SDA]

I2C_SDA4

I2C_SCL4

FT24C256A-ESR-T

NVRAM

DTA2010M

AMP

[GPIO_51_TUNER0_SDA]

[GPIO_52_TUNER0_SCL]

I2C_SDA2

I2C_SCL2

DT1805

LNB

TDJN-G501D

TUNER

1.8 k ȳ

+3.3V_NOR

1.8k ȳ

+3.3V_NOR

33 ȳ

100ȳ

33 ȳ

EPI / CEDS only

8. K3Lp I2C Map

- 19 -

[ST_GPIO_05_IR_RX]

[ST_GPIO_00_WOL_WAKE_UP]

WOL/ETH_POWER_ON

USB_CTL2

K3Lp

MICOM

USB2_2.0 OCP USB2

[RTC_XO_USBOCD0]

[GPIO_79_USB_PWR0_SD_WP]

INSTANT_BOOT

/USB_OCD2

USB_CTL3

USB3_2.0 OCP USB3

[RTC_XI_USBOCD1]

[GPIO_78_USB_PWR1_SD_CD]

/USB_OCD3

[RST]

SOC_RESET

[AH16,AH17,AG16,AG17,AJ16]

BIT0~4

HW option

ADC 1~5

[GPIO_119_PC_RST]

PCM_RESET

CI_SLOT

CI power

enable control

[AIO2R_CMD_VCC_SC]

PCM_5V_CTL

Panel

[GPIO_4_VBY_HTPD/TCON_14]

EPI_MCLK

[GPIO_5_VBY_LOCK/EPLOCK]

LOCKAn

[GPIO7_PMIC_RESET]

PMIC_RESET

PMIC

[GPO011_PWM_DIM_1]

[GPIO010_PWM_DIM_0]

PWM_DIM2

POWER

PWM_DIM

[GPO012_LD_SPI1_SCK]

L/DIM_M0_SCLK

[GPO013_LD_SPI1_SDO]

L/DIM_M0_MOSI

[GPO014_LD_SPI1_SYNC]

L/DIM_M0_VS

EPI_GCLK

[GPO_1_TCON_I2C_EN/TCON_2]

[VINBN_VIDCORE]

VID_CORE

CORE DCDC

[VINRP_TUNER0_REST]

/TU_RESET1

Tuner

/TU_RESET2

[VINGP_DEMOD_RESET]

[AI2L_AMP_RESET_N]

AMP_RESET_N

Audio AMP

[AI3R_COMP1_DET]

COMP1_DET

Component/AV Jack

[AIO1L_AV1_CVBS_DET]

AV1_CVBS_DET

[VDBSOUT_SC_PWR_SEL]

SMARTCARD_PWR_SEL

Japan B-CAS

[AIO2L_HP_DET]

HP_DET

H/P Jack

9. GPIO(K3Lp)

- 20 -

RTK ˀ K3L

IC100

1 [P60/SCLA0] / 2 [P61/SDAA0]

13 [P50//INTP1/SI11/SDA11]

18 [P14/RXD2/SI20/SDA20]

RS232C

CONTROL I/F

IC7200

SOC_RX/TX

[P24/ANI4] 28

[P23/ANI3] 29

MICOM DEBUG 4P

P3000

12507WS-04L

[P40/TOOL0] 39

MICOM_DEBUG

AMP

IC5800

DTA2010M

AMP_MUTE

MODEL1_OPT_0/1/2/ 3

4 [P63]

5 [P31/TI/03/TO03/INTP4]

GND

+13V TO PANEL_VCC

PANEL_CTL

HDMI 1 / 2 / 3 /4

JK3101/JK3102/JK3103/JK3104

HDMI_CEC

RESET IC

IC1300

14 [P51/INTP2/SO11]

POWER_DET

POWER WAFER

P1001

INV_CTL

MODE_SELECT_PWM1

RL_ON

I2C_SCL_MICOM / I2C_SDA_MICOM

WOL/ETH_POWER_ON

SOC_RESET

INSTANT_BOOT

SYSTEM_DEBUG

HP AMP

IC6300

TPA6138A2

[P25/ANI5] 27

SIDE_HP_MUTE

OPT0 NON LOGO LCD/LOGO LCD

NON LOGO OLED/LOGO OLED

OPT1 TV-NON EPI/BOX/TV EPI/BOX

OTP2 RESERVED/ RESERVED/9_KEY/9_KEY_NON

OPT3 M16/RTK/H15

[RESET] 40

MICOM_RESET

MICOM X-TAL

X3000

32.768KHz

[P124/XT2/EXCLKS] 41

[P123/XT1] 42

17 [P15/PCLBUZ1/SCK20/SCL20]

WOL_CTL

51P VX1 Wafer

1.0V DCDC Eth STDBY

IC2307

TLV62565DBVR

EWBS_TUNER

[P16/TI01/TO01/INTP5] 16

AM_MODE_DET_OLED

[P137/INTP0] 43

HDMI EXT EDID

IC3401

BR24G02FJ

22 [P10/SCK00/SCL00]

7 [P74/KR4/INTP8/SI01/SDA01]

19 [P13/TXD2/SDA20]

36 [P140/PCLBUZ0/INTP6]

IR / KEY/WIFI/BT

P4000

10 [P71/KR1/SI21/SDA21] / 11 [P70/KR0/SIK21/SCL21]

31 [P21/ANI1/AVREFM] / 32 [P20/ANI0/AVREFP]

38 [P41/TI07/TO07]

6 [P75/KR5/INTP9/SCK01/SCL01]

20 [P12/SO00/TXD0/TOOLTXD]

21 [P11/SI00/RXD0/TOOLRXD/SDA00]

EWBS_TU

TUxxxx

EDID_WP

3D&L_DIM_EN

[P146] 23

[P62] 3

1.5V DCDC

IC2303

SYVL83

33 [P130]

3.3V NORMAL DCDC

IC2300

TPS563208

[P72/KR2/SO21] 9

POWER_ON/OFF2_3

0.95V CORE/CPU DCDC

IC2302

TPS51362RVER

1.8V eMMC LDO

IC2301

TJ4320GDP-ADJ

POWER_ON/OFF2_4

[P01/TO00/RXD1] 34

12 [P30/INTP3/RTC1HZ/SCK11/SCL11]]

[P17/TI02/TO02] 15

POWER_ON/OFF1

13V-5V NORMAL DCDC

IC2500

TPS564208

24 [P147/ANI18]

25 [P27/ANI7]

26 [P26/ANI6]

WIFI_EN

[P22/ANI2] 30

35 [P00/TI00/TXD1]

[P122/X2/EXCLK] 44

T_CON_SYS_POWER_OFF_OLED

[P121/X1] 45

IR

EYE_SCL / EYE_SDA

BT_WAKEUP_DEVICE

WOL/WIFI_POWER_ON

COMBO_RESET

BT_WAKEUP_HOST

KEY1 / KEY2

LED_R

1.2V Demod LDO

IC6900

TJ4320GDP-ADJ

GND

+3.5V WIFI

37 [P120/ANI19]

RETENTION_DISABLE

8 [P73/KR3/SO01]

* Depending on Model

10. GPIO(MICOM – RENESAS)

- 21 -