LG 65SE3D-B INSTALLATION INSTRUCTIONS

INSTALLATION MANUAL

LG Digital
Signage

(MONITOR SIGNAGE)

Please read this manual carefully before operating your set and retain it for future reference.

L15

www.lg.com

2

TABLE OF CONTENTS

ENGLISH

ACCESSING INSTALLATION MENU

........................................................4

INSTALLATION MENU ..................5

- LG Digital Signage Setup menu ................................5

Signage Mode Operation

Power On Status

Key Operation

IR Operation / Local Key Operation

Limited Mode

Input Source Change

Menu Display

OSD Display

Power On Default (Input Source, A/V Setting,
Aspect Ratio)

Input Source

A/V Setting

Aspect Ratio

Wake On LAN

DPM

Digital Audio Input

Speaker

Power On Delay

Pivot Mode

OSD Portrait Mode (Off, 90, 270)

Intelligent Auto

Master/Slave Mode

Time Sync Clock

Sync Mode

DPM Wakeup Control

Still Image Detecting

PM Mode

Factory Reset

OPS/PC Power Control

Interface Selection

Check Screen

Factory Reset VS Initial Setting

- USB Cloning .....................................................................13

Ez Download

Receive from USB

Send to USB

Logo Image Download

Send to DaisyChain

- Password Change ..........................................................18

- Set ID Setup ......................................................................19

Set ID Lock

Set ID

Auto Set ID

Reset ID

- Configuration Setup .....................................................20

Splash Offset Time

U SB Auto Playback

15 Min Auto Off

Automatic Standby

Screen Saver Cube

- Lock Mode ......................................................................... 22

USB

Initial Setting

- External Speaker / Audio out ..................................23

Output Control

- Fail Over ..............................................................................24

You can set Mode to Off, Auto, or Manual.

You can set USB to Off, Movie, or Photo.

Fail Over priority when set to Auto

- ISM Method ...................................................................... 26

Mode

Timer

Period

Time

Still Image Detecting and ISM Method

Bar Image

Bar Color

Bar Transparency

Bar Direction

User Image

- Easy Brightness Control ............................................30

- SuperSign Server Setup .............................................31

Player Name

Server IP Setting

Server IP Status

- Holiday Schedule ............................................................32

- No Signal Image ..............................................................33

- Crestron ..............................................................................34

- Digital Signage Media Player ...................................34

Executable content

Using the My Media menu to play files

Auto-play on USB insertion

Distributing and playing content via SuperSign
W

3

ENGLISH

4

ACCESSING INSTALLATION MENU

ENGLISH

1 Press and hold the SETTINGS button for more than 5 seconds.

PICTURE

OPTION

AUDIO TIME

NETWORK

MY MEDIA

2 Enter the correct password (default: 0000) and press the OK button.

HDMI

(DTV)

No Signal

3 When the Installation Menu is displayed, select the desired item.

Installation Menu (V 3.0)

LG Digital Signage Setup

LG Digital Signage Setup

USB Cloning

Password Change

Set ID Setup

Configuration Setup

Lock Mode

External Speaker / Audio out

Fail Over

ISM Method

Easy Brightness Control

Installation Menu (V 3.0)

SuperSign Server Setup

Holiday Schedule

No Signal Image

Crestron

S/W : xx.xx.xx.xx Micom : x.xx.x

OK

S/W : xx.xx.xx.xx Micom : x.xx.x

OK

5

INSTALLATION MENU

NOTE

• Default values may differ by region.

LG Digital Signage Setup menu

• Use this menu to configure the Digital Signage after in stallation.

Installation Menu (V 3.0)

LG Digital Signage Setup

USB Cloning
Password Change
Set ID Setup
Configuration Setup
Lock Mode
External Speaker / Audio out
Fail Over
ISM Method
Easy Brightness Control

S/W : xx.xx.xx.xx Micom : x.xx.x

Installation Menu (V 3.0)

SuperSign Server Setup

Holiday Schedule

No Signal Image

Crestron

S/W : xx.xx.xx.xx Micom : x.xx.x

OK

OK

LG Digital Signage Setup

Signage Mode Operation

• Power On Status

• Key Operation

• IR Operation

• Local Key Operation

• Limited Mode

• Input Source Change

• Menu Display

• OSD Display

Previous

ENGLISH

Yes

LST

No

Normal

Normal

No

Yes

Yes

Yes

OK

LG Digital Signage Setup

• Power On Default

• Input Source

• A/V Setting

• Aspect Ratio

• Wake On LAN

• DPM

• Digital Audio Input

• Speaker

• Power On Delay

Previous

No

Off

No

Disable

Off

10min.

Analog

On

Off

LG Digital Signage Setup

• Pivot mode

• OSD Portrait Mode

• Intelligent Auto

• Master/Slave Mode

• Time Sync Clock

• Sync Mode

• DPM Wakeup Control

• Still Image Detecting

• PM Mode

Previous

OK

Off

Off

On

Slave

Stand-by

Off

Clock

Yes

Power Off

OK

LG Digital Signage Setup

• OPS/PC Power Control

• Factory Reset

Previous

Off

OK

6

Signage Mode Operation

ENGLISH

• Enable or disable all Signage Mode Operation functions by setting the feature to Yes or No.

• If you set Signage Mode Operation to Yes, all Signage Mode functions are enabled.

• If you set Signage Mode Operation to No, all Signage Mode functions are disabled, and the product operates with its

default settings.
(Depending on the model, this feature may not be supported.)

Power On Status

• You can select the operating status of the monitor when the main power is turned on.

• You can choose PWR, STD, or LST.

• PWR sets the monitor status to On whenever the main power is turned on.

• STD sets the monitor status to Standby when the main power is turned on.

• LST sets the monitor status back to its previous status. As in Power Backup mode, if you turn off the main power

while the monitor is turned on, the monitor status changes back to On. Also, if you turn off the main power while the
monitor is in standby mode, the monitor goes into standby mode.
(This feature may not be available with some models.)

Key Operation

• This feature allows you to manage the usability and operation of the local/front keys and your remote control. It

works according to the “IR Operation” settings.
(This feature may not be available with some models.)

IR Operation / Local Key Operation

• This feature allows you to set how the product operates after receiving a signal from a LG remote control or local key.

(0 - Normal, 1 - Use PWR Only, 2 - Block All)

• Selecting ‘Block All’ blocks any signal coming from a LG remote control/local key. (Power On feature is available.)

• Selecting ‘Use PWR Only’ blocks any signal coming from a LG remote control/local key, except the Power button.

• Selecting ‘Normal’ enables signals from any LG remote control/local key to be received normally.

• There are keys that must be operated in ‘Service mode’ when ‘Use PWR Only’ or ‘Block All’ is selected: In-Start, In-

Stop, Power-Only, ADJ, Installation Menu, P-Check, and S-check.
(This feature may not be available with some models.)

NOTE

• When all IR key signals or all local key signals are blocked, the “Power On Status” value switches to “PWR”. Changing

this value is not impossible to ensure the correct powering on operation. (To prevent mistakes by the user)

Limited Mode

• This feature allows you inhibit the operations of particular Signage functions. This feature works according to the

‘Input Source Change’, ‘Menu Display’, or ‘OSD Display’ settings.
(This feature may not be available with some models.)

Input Source Change

• Enable or disable input source changes by setting this feature to Yes or No.

• If you set this feature to No (changes disabled), the INPUT key is disabled.

• If you set this feature to Yes (changes enabled), the input source can be changed.

(This feature may not be available with some models.)

7

Menu Display

• Setting this feature to Yes will display the menu. Setting this feature to No will hide the menu.

• However, even if you have set this feature to No, you can easily open the Installation Menu by pressing and holding

the Menu button for more than 5 seconds.
(This feature may not be available with some models.)

OSD Display

• Enable or disable OSDs by setting this feature to Yes (displayed) or No (not displayed).

• If you set this feature to No (not displayed), OSDs other than Installation Menu are not displayed.

(This feature may not be available with some models.)

Power On Default (Input Source, A/V Setting, Aspect Ratio)

• You can configure ‘Input Source’, ‘A/V Setting’, and ‘Aspect Ratio’ after the monitor is turned on.

• You can set this feature to Yes (enabled) or No (disabled).

• If you set ‘Power On Default’ to No, the settings for ‘Input Source’, ‘A/V Setting’, and ‘Aspect Ratio’ are not

applied.

• If you set ‘Power On Default’ to Yes, the settings for the menus above are applied.

(This feature may not be available with some models.)

Input Source

• This feature allows you to set whether to use a new input source or a pre-existing input source.

• Set ‘Input Source’ to Off to use the pre-existing input source.

• You can use any of the sources supported by the given model as the input source.

• If both ‘Input Source’ and ‘On Time’ have been set, ‘Input Source’ takes priority.

(This feature may not be available with some models.)

A/V Setting

• When your monitor is powered on, you can set certain video options.

• If you set this feature to Yes, the video settings configured before entering the Installation Menu are saved. In

addition, even if you changed the video settings before turning off the monitor, the saved settings are restored when
you turn the monitor on again.

• Saves video settings: Picture Mode, DPM Select, Smart Energy Saving, Backlight, Contrast, Brightness, Sharpness,

Color, Tint, and Color Temp.

• Saves audio settings: Sound Mode and Balance.

(This feature may not be available with some models.)

Aspect Ratio

• This feature allows you to set the screen aspect ratio applied to your monitor when turned on.

• Selecting ‘Disable’ sets the screen aspect ratio to ‘Aspect Ratio’ when the monitor is turned on.

• Selecting ‘Set By Program’ sets the screen aspect ratio to ‘Set By Program’ when the monitor is turned on.

• Selecting ‘4:3’ sets the screen aspect ratio to ‘4:3’ when the monitor is turned on.

• Selecting’16:9’ sets the screen aspect ratio to ‘16:9’ when the monitor is turned on.

(This feature may not be available with some models.)

ENGLISH

8

Wake On LAN

ENGLISH

• Set whether to use the ‘Wake On LAN’ feature.

• You can set ‘Wake On LAN’ to On or Off.

• If you set this feature to On, ‘Wake On LAN’ is enabled and you can turn the product on remotely via a LAN.

• If you set this feature to Off, ‘Wake On LAN’ is disabled.

(This feature may not be available with some models.)

DPM

• Set whether to use ‘Display Power Management (DPM)’.

• You can set this feature to Off, 5 sec, 10 sec, etc.

• If this feature is not set to Off, the monitor will enter Power Saving Mode when there is no input signal.

• If you set this feature to Off, DPM is disabled.

(This feature may not be available with some models.)

Digital Audio Input

• You can set the audio for each input as ‘Analog’ or ‘Digital’.

• In the case of RGB input, audio is fixed as ‘Analog’.

• In the case of digital input, you can select ‘Analog’ or ‘Digital’ for audio.

(This feature may not be available with some models.)

Speaker

• You can restrict the audio settings by choosing whether or not to use the speakers.

• If you set this feature to Off, audio output is disabled, and you cannot enter the ‘Audio’ menu.

• If you set this feature to On, audio output is enabled, and the ‘Audio’ menu is accessible.

(This feature may not be available with some models.)

Power On Delay

• When multiple monitors are connected, this feature enables the monitors to turn on at specified time intervals to

prevent overload. You can choose an interval value between 1 and 250 seconds.
(This feature may not be available with some models.)

Pivot Mode

• This feature allows you to rotate the screen 180 degrees.

• Both the input signal and OSD rotate.

• You can set this feature to On or Off.

• If you set this feature to Off, the function is disabled.

• If you set this feature to On, the screen rotates 180°.

• If any changes are made, they are applied after reboot.

(This feature may not be available with some models.)

OSD Portrait Mode (Off, 90, 270)

• This feature allows you to rotate the OSD clockwise.

• You can set this feature to Off/90/270.

• If you set this feature to Off, the function is disabled.

• If you set this feature to 90, the OSD rotates clockwise 90 degrees.

• If you set this feature to 270, the OSD rotates clockwise 270 degrees.

(This feature may not be available with some models.)

9

Intelligent Auto

• You can set this feature to On (enabled) or Off (disabled).

• If you change the screen resolution after setting this feature to ‘Yes’, the display is automatically adjusted to the new

resolution.
(This feature may not be available with some models.)

Master/Slave Mode

• This feature allows you to sync monitors connected via RS-232C.

• When various monitors are connected via RS-232C, the forefront monitor becomes the Master.

• Once the Master is selected, the rest become Slaves.

• If you want to change the Master monitor, you must change it in Master/Slave Mode.

(This feature may not be available with some models.)

NOTE

• The Master/Slave Mode menu is only enabled when Picture ID is set to Off.

• When entering or editing Master/Slave Mode, the menu cursors on the Slave monitors may not be moved.

Time Sync Clock

• This feature syncs the Slave monitors’ clocks to the Master monitor’s at a specified time via RS-232C.

• On the Master monitor, you can set the sync time as well as setting Time Sync Clock to Off .

• You can select a sync time between 0:00 - 23:00.

• While Time Sync Clock is performed, RS-232C control of other commands may not work.

(This feature may not be available with some models.)

NOTE

• To synchronize Time Sync Clock, be sure to set each slave monitor’s clock so that they are at least one minute later

than the master monitor’s clock.

• If the Clock setting is Auto, the setting is changed to Manual when Time Sync Clock runs.

ENGLISH

10

Sync Mode

ENGLISH

• This feature allows you to sync the start times of contents (videos or images that have been distributed by SuperSign

Software) played back on the Master and Slave monitors.

• If you set Sync Mode to Off, the sync feature is disabled.

• A Slave monitor plays contents at the same time as the Master monitor.

• While Sync Mode is performed, RS-232C control of other commands may not work.

(This feature may not be available with some models.)

DPM Wakeup Control

• This feature sets conditions for releasing the DPM status according to the DVI/HDMI’s processing of digital signals.

• Clock: Checks the clock signal of the digital signal and, if the clock signal exists, releases the DPM status.

• Sync: Releases the DPM status when both the clock signal and data of the digital signal are entered.

Still Image Detecting

• This feature detects still images.

• If you set this feature to Yes, you can use the RS-232C command for detecting still images.

PM Mode

• This feature activates some of the monitor’s functions after it enters Off status, allowing the monitor to remain

practically the same as when it is turned on.

• Power Off: All functions remain turned off except some functions (Power, Time, etc.) when the monitor turns off.

(Extended Display Identification Data (EDID) may be sustained depending on the input and model.)

• Sustain Aspect Ratio: Sustains Extended Display Identification Data (EDID) even when the monitor is turned off.

• Screen Off: Only turns off the screen and audio when the monitor enters Auto Off/Automatic Standby/DPM.

Network-based control is possible.

• Screen Off Always: Has the same function as PM Mode’s Screen Off. Entering and releasing the Screen Off status

using a remote control is also possible.

11

Factory Reset

• This feature allows you to restore all set values to their factory default values.

• If you set this feature to Yes, all Signage settings except UTT setting (the Signage panel’s operational hours) are

restored to their factory default settings.
(This feature may not be available with some models.)

All user settings will be reset.

Still Continue?

Yes No

OPS/PC Power Control

• You can control the power of the OPS (media player) by turning the display power on or off.

• Disable: Disables the PC Power Control.

• Sync (on): Synchronizes the power status of the OPS (media player) only when the monitor is turned on.

• Sync (on/off): Synchronizes the power status of the OPS (media player) with the monitor.

• The PC Power Control feature can be used with the external RS-232C connection of the media player.

(This feature may not be supported in certain models.)

Interface Selection

• You can configure serial communication with the connected OPS.

• RS-232C: Enables communication with external devices via the serial port.

• OPS: Enables communication via the OPS connected to the product.

• Interface Selection is enabled only when the OPS kit is connected.

(This feature may not be supported in certain models.)

Check Screen

• The Check Screen feature judges whether there are abnormalities on the edges of the screen. R, G, and B OSDs are

formed on the screen at one second intervals and an RGB sensor tests the areas.

• If set to On, the Check Screen feature is enabled.

• If set to Off, the Check Screen feature is disabled.

• If the Portrait mode is set to 90 or 270, the Check Screen feature is off and deactivated.

• If the Pivot mode is On, the Check Screen feature is off and deactivated.

• When the Portrait mode and Pivot mode is off, the Check Screen feature is activated.

(This feature may not be supported in certain models.)

ENGLISH