LG 60UB820T Manual book
OWNER’S MANUAL
*
LED TV
* LG LED TVs are LCD TVs with LED backlighting.
Please read this manual carefully before operating
your set and retain it for future reference.
UB80**
UB82**
UB83**
www.lg.com
*MFL68140541*
P/NO : MFL68140541 (1407-REV00)
Printed in Korea
TABLE OF CONTENTS
2
ENGLISH
TABLE OF CONTENTS
ENG
3 LICENSES
3 OPEN SOURCE SOFTWARE
NOTICE
3 EXTERNAL CONTROL DEVICE
SETUP
4 SAFETY INSTRUCTIONS
10 - Viewing 3D Imaging
(Only 3D models)
11 INSTALLATION PROCEDURE
11 ASSEMBLING AND PREPARING
11 Unpacking
14 Separate purchase
15 Parts and buttons
16 - Using the joystick button
17 Lifting and moving the TV
18 Setting up the TV
18 - Attaching the stand
19 Mounting on a table
20 Mounting on a wall
22 Tidying cables
28 REMOTE CONTROL
29 MAGIC REMOTE FUNCTIONS
30 Registering Magic Remote
30 How to use Magic Remote
31 Precautions to Take when Using the
Magic Remote
31 USING THE USER GUIDE
32 MAINTENANCE
32 Cleaning your TV
32 - Screen, frame, cabinet and stand
32 - Power cord
32 TROUBLESHOOTING
33 SPECIFICATIONS
22 MAKING CONNECTIONS
23 Antenna connection
23 HDMI connection
24 DVI to HDMI connection
25 Component connection
25 Composite connection
26 Audio connection
26 - Digital optical audio connection
26 Headphone connection
27 USB connection
27 MHL connection
WARNING
yIf you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
yIf you ignore the caution message, you
may be slightly injured or the product may
be damaged.
NOTE
yThe note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
3
LICENSES
Supported licenses may differ by model. For more information about licenses, visit
www.lg.com
.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained
in this product, please visit
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of media, shipping and handling) upon email request
to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased
the product.
http://opensource.lge.com
.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please
visit www.lg.com.
ENGENGLISH
SAFETY INSTRUCTIONS
4
ENGLISH
SAFETY INSTRUCTIONS
ENG
Please read these safety precautions carefully before using the product.
WARNING
yDo not place the TV and/or remote control
in the following environments:
- A location exposed to direct sunlight
- An area with high humidity such as a
bathroom
- Near any heat source such as stoves
and other devices that produce heat
- Near kitchen counters or humidifiers
where they can easily be exposed to
steam or oil
- An area exposed to rain or wind
- Near containers of water such as vases
Otherwise, this may result in fire, electric
shock, malfunction or product deformation.
yMake sure to connect Mains cable to
compliant AC mains socket with Grounded
earth pin. (Except for devices which
are not grounded on earth.) Otherwise
possibility you may be electrocuted or
injured.
yInsert power cable plug completely into
wall socket otherwise if not secured
completely into socket, fire ignition may
break out.
yDo not place the product where it might be
exposed to dust.
This may cause a fire hazard.
yMains Plug is the TV connecting/
disconnecting device to AC mains electric
supply. This plug must remain readily
attached and operable when TV is in use.
yDo not touch the power plug with wet
hands. Additionally, if the cord pin is wet
or covered with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due to excess
moisture.
yEnsure the power cord does not come into
contact with hot objects such as a heater.
This may cause a fire or an electric shock
hazard.
yDo not place a heavy object, or the
product itself, on power cables.
Otherwise, this may result in fire or electric
shock.
yBend antenna cable between inside and
outside building to prevent rain from
flowing in.
This may cause water damaged inside the
Product and could give an electric shock.
SAFETY INSTRUCTIONS
Desiccant
5
yWhen mounting TV onto wall make sure to
neatly install and isolate cabling from rear
of TV as to not create possibility of electric
shock /fire hazard.
yDo not plug too many electrical devices
into a single multiple electrical outlet.
Otherwise, this may result in fire due to
over-heating.
yDo not drop the product or let it fall over
when connecting external devices.
Otherwise, this may result in injury or
damage to the product.
yKeep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach
of children.
yDo not let your children climb or cling onto
the TV. Otherwise, the TV may fall over,
which may cause serious injury.
yDispose of used batteries carefully
to ensure that a small child does not
consume them. Please seek DoctorMedical Attention immediately if child
consumes batteries.
yDo not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not
touch the power cable right after plugging
into the wall input terminal. You may be
electrocuted. (Depending on model)
yDo not put or store inflammable
substances near the product. There is a
danger of combustion/explosion or fire due
to careless handling of the inflammable
substances.
yDo not drop metallic objects such as
coins, hair pins, chopsticks or wire into
the product, or inflammable objects such
as paper and matches. Children must
pay particular attention. Electrical shock,
fire or injury can occur. If a foreign object
is dropped into the product, unplug the
power cord and contact the service centre.
ENGENGLISH
yDo not spray water on the product or
scrub with an inflammable substance
(thinner or benzene). Fire or electric shock
accident can occur.
SAFETY INSTRUCTIONS
6
yDo not allow any impact, shock or any
ENGLISH
ENG
objects to fall into the unit, and do not
drop anything onto the screen.
You may be injured or the product can be
damaged.
yNever touch this product or antenna
during a thunder or lighting storm.
You may be electrocuted.
yNever touch the wall outlet when there is
leakage of gas, open the windows and
ventilate.
It may cause a fire or a burn by a spark.
yDo not disassemble, repair or modify the
product at your own discretion.
Fire or electric shock accident can occur.
Contact the service centre for check,
calibration or repair.
yUnplug the TV from AC mains wall socket if you
do not intend to use the TV for a long period of
time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric
leakage/shock/fire.
yApparatus shall not be exposed to dripping
or splashing and no objects filled with liquids,
such as vases, shall be placed on the
apparatus.
yDo not install this product on a wall if it could
be exposed to oil or oil mist.
This may damage the product and cause it to
fall.
CAUTION
yInstall the product where no radio wave occurs.
yThere should be enough distance between an
outside antenna and power lines to keep the
former from touching the latter even when the
antenna falls.
This may cause an electric shock.
yIf any of the following occur, unplug the product
immediately and contact your local service
centre.
- The product has been impacted by shock
- The product has been damaged
- Foreign objects have entered the product
- The product produced smoke or a strange
smell
This may result in fire or electric shock.
yDo not install the product on places such
as unstable shelves or inclined surfaces.
Also avoid places where there is vibration or
where the product cannot be fully supported.
Otherwise, the product may fall or flip over,
which may cause injury or damage to the
product.
SAFETY INSTRUCTIONS
7
yIf you install the TV on a stand, you need
to take actions to prevent the product from
overturning. Otherwise, the product may
fall over, which may cause injury.
yIf you intend to mount the product to a
wall, attach VESA standard mounting
interface (optional parts) to the back of the
product. When you install the set to use
the wall mounting bracket (optional parts),
fix it carefully so as not to drop.
yOnly use the attachments / accessories
specified by the manufacturer.
yWhen installing the antenna, consult with a
qualified service technician. If not installed
by a qualified technician, this may create
a fire hazard or an electric shock hazard.
yWe recommend that you maintain a
distance of at least 2 to 7 times the
diagonal screen size when watching TV.
If you watch TV for a long period of time,
this may cause blurred vision.
yDo not place non-rechargeable batteries
in charging device.
yMake sure there are no objects between
the remote control and its sensor.
ySignal from Remote Control can be
interrupted due to external/internal lighting
eg Sunlight, fluorescent lighting.If this
occurs turn off lighting or darken viewing
area.
yWhen connecting external devices such
as video game consoles, make sure the
connecting cables are long enough.
Otherwise, the product may fall over,
which may cause injury or damage the
product.
yDo not turn the product On/Off by
plugging-in or unplugging the power plug
to the wall outlet. (Do not use the power
plug for switch.)
It may cause mechanical failure or could
give an electric shock.
ENGENGLISH
yOnly use the specified type of battery.
This could cause damage to the remote
control.
yDo not mix new batteries with old
batteries. This may cause the batteries to
overheat and leak.
yBatteries should not be exposed to
excessive heat. For example, keep away
from direct Sunlight, open fireplace and
electric heaters.
yPlease follow the installation instructions
below to prevent the product from
overheating.
- The distance between the product and
the wall should be more than 10 cm.
- Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in
a cupboard).
- Do not install the product on a carpet or
cushion.
- Make sure the air vent is not blocked by
a tablecloth or curtain.
Otherwise, this may result in fire.
SAFETY INSTRUCTIONS
8
yTake care not to touch the ventilation
ENGLISH
ENG
openings when watching the TV for long
periods as the ventilation openings may
become hot. This does not affect the
operation or performance of the product.
yPeriodically examine the cord of your
appliance, and if its appearance indicates
damage or deterioration, unplug it,
discontinue use of the appliance, and
have the cord replaced with an exact
replacement part by an authorized
servicer.
yPrevent dust collecting on the power plug
pins or outlet.
This may cause a fire hazard.
yProtect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or
walked upon. Pay particular attention to
plugs, wall outlets, and the point where
the cord exits the appliance.
yWhen cleaning the product and its
components, unplug the power first
and wipe it with a soft cloth. Applying
excessive force may cause scratches or
discolouration. Do not spray with water
or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives
or wax, benzene, alcohol etc., which can
damage the product and its panel.
Otherwise, this may result in fire, electric
shock or product damage (deformation,
corrosion or breakage).
yAs long as this unit is connected to the AC
wall outlet, it is not disconnected from the
AC power source even if you turn off this
unit by SWITCH.
yWhen unplugging the cable, grab the plug
and unplug it, by pulling at the plug. Don’t
pull at the cord to unplug the power cord
from the power board, as this could be
hazardous.
yDo not press strongly upon the panel with
a hand or sharp object such as nail, pencil
or pen, or make a scratch on it, as it may
cause damage to screen.
yAvoid touching the screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
yWhen moving the product, make sure
you turn the power off first. Then, unplug
the power cables, antenna cables and all
connecting cables.
The TV set or power cord may be
damaged, which may create a fire hazard
or cause electric shock.
yWhen moving or unpacking the product,
work in pairs because the product is
heavy.
Otherwise, this may result in injury.
SAFETY INSTRUCTIONS
9
yContact the service centre once a year to
clean the internal parts of the product.
Accumulated dust can cause mechanical
failure.
yRefer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
yIf the product feels cold to the touch, there
may be a small “flicker” when it is turned
on. This is normal, there is nothing wrong
with product.
yYou may find different brightness and
colour of the panel depending on your
viewing position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
yDisplaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from
a video game) for a prolonged time may
cause damage to the screen, resulting
in retention of the image, which is known
as image sticking. The warranty does not
cover the product for image sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period
(2 or more hours for LCD, 1 or more hours
for Plasma).
Also, if you watch the TV at a ratio of 4:3
for a long time, image sticking may occur
on the borders of the panel.
This phenomenon also occurs in thirdparty products and is not subject to
exchange or refund.
ENGENGLISH
yThe panel is a high technology display
product with resolution of two million to six
million pixels. You may see tiny black dots
and/or brightly coloured dots (red, blue or
green) at a size of 1 ppm on the panel.
This does not indicate a malfunction and
does not affect the performance and
reliability of the product.
This phenomenon also occurs in thirdparty products and is not subject to
exchange or refund.
Generated Sound
y
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing:
A low level noise is generated from a highspeed switching circuit, which supplies a large
amount of current to operate a product. It varies
depend-ing on the product.
This generated sound does not affect the
performance and reliability of the product.
SAFETY INSTRUCTIONS
10
Viewing 3D Imaging
ENGLISH
ENG
(Only 3D models)
WARNING
Viewing Environment
yViewing Time
- When watching 3D contents, take 5 - 15
minute breaks every hour. Viewing 3D
contents for a long period of time may
cause headache, dizziness, fatigue or
eye strain.
Those that have a photosensitive
seizure or chronic illness
ySome users may experience a seizure or
other abnormal symptoms when they are
exposed to a ashing light or particular
pattern from 3D contents.
yDo not watch 3D videos if you feel nausea,
are pregnant and/ or have a chronic illness
such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
y3D Contents are not recommended to those
who suffer from stereo blindness or stereo
anomaly. Double images or discomfort in
viewing may be experienced.
yIf you have strabismus (cross-eyed),
amblyopia (weak eyesight) or astigmatism,
you may have trouble sensing depth and
easily feel fatigue due to double images. It
is advised to take frequent breaks than the
average adult.
yIf your eyesight varies between your right
and left eye, revise your eyesight prior to
watching 3D contents.
CAUTION
Viewing Environment
Viewing Distance
y
- Maintain a distance of at least twice the
screen diagonal length when watching
3D contents. If you feel discomfort in
viewing 3D contents, move further away
from the TV.
Viewing Age
yInfants/Children
- Usage/ Viewing 3D contents for children
under the age of 5 are prohibited.
- Children under the age of 10 may
overreact and become overly excited
because their vision is in development
(for example: trying to touch the
screen or trying to jump into it. Special
monitoring and extra attention is
required for children watching 3D
contents.
- Children have greater binocular
disparity of 3D presentations than adults
because the distance between the eyes
is shorter than one of adults. Therefore
they will perceive more stereoscopic
depth compared to adults for the same
3D image.
yTeenagers
- Teenagers under the age of 19 may
react with sensitivity due to stimulation
from light in 3D contents. Advise them
to refrain from watching 3D contens for
a long time when they are tired.
yElderly
- The elderly may perceive less 3D
effect compared to the youth. Do not sit
closer to the TV than the recommended
distance.
Symptoms which require discontinuation
or refraining from watching 3D contents
yDo not watch 3D contents when you feel
fatigue from lack of sleep, overwork or
drinking.
yWhen these symptoms are experienced,
stop using/watching 3D contents and get
enough rest until the symptom subsides.
- Consult your doctor when the symptoms
persist. Symptoms may include
headache, eyeball pain, dizziness,
nausea, palpitation, blurriness,
discomfort, double image, visual
inconvenience or fatigue.
Cautions when using the 3D glasses
Make sure to use LG 3D glasses. Otherwise,
y
you may not be able to view 3D videos
properly.
Do not use 3D glasses instead of your
y
normal glasses, sunglasses or protective
goggles.
Using modied 3D glasses may cause eye
y
strain or image distortion.
Do not keep your 3D glasses in extremely
y
high or low temperatures. It will cause
deformation.
The 3D glasses are fragile and are easy
y
to be scratched. Always use a soft, clean
piece of cloth when wiping the lenses. Do
not scratch the lenses of the 3D glasses
with sharp objects or clean/wipe them with
chemicals.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
11
NOTE
yImage shown may differ from your TV.
yYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yThe available menus and options may differ from the input source or product model that you are
using.
yNew features may be added to this TV in the future.
yThe TV can be placed in standby mode in order to reduce the power consumption. And the TV
should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yThe energy consumed during use can be signicantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
4 Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
ENGENGLISH
CAUTION
yDo not use any unapproved items to ensure the safety and product life span.
yAny damages or injuries by using unapproved items are not covered by the manufacturer’s
warranty.
ySome models have a thin lm attached on to the screen and this must not be removed.
ASSEMBLING AND PREPARING
12
ENGLISH
ENG
Magic remote, Batteries
(AA)
(Only UB80**, UB82**,
UB83**)
(See p.29)
Power Cord
(Depending on model)
AV MODE
INPUT
ENERGY
TV
SAVING
1 2 3
4 5 6
7 809
FLASHBK
LIST
MARK
FAV
P
A
G
3D
CHVOL
E
MUTE
INFO
MENU
Q.MENU
ENTER
EXIT
BACK
L/R SELECT
FREEZE
RATIO
Remote control, Batteries
(AAA)
The remote control will not be
included for all sales market.
(Depending on model)
(See p.28)
Cable Holder
(Depending on model)
(See p.22)
Owner’s manual
Cable Managements
2EA
(See p.22)
Ferrite core
(Depending on model)
(See p.13)
Stand Screws
(Only UB83**)
4EA, M4 X L21
(See p.18)
Stand Screws
(Only UB80**, UB82**)
4EA, M4 X L20
(See p.18)
Stand Bases
(Only UB83**)
(See p.18)
Stand Bases
(Only UB80**, UB82**)
(See p.18)
Component gender cable
(See p.25)
ASSEMBLING AND PREPARING
<
<
13
ENGENGLISH
Composite gender cable
(See p.25)
NOTE
yThe items supplied with your product may vary depending on the model.
yProduct specications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not t into your TV’s USB port.
B
A
Cinema 3D Glasses
The number of 3D glasses
may differ depending on the
model or country.
(Only UB83**)
B
*A
10 mm
=
18 mm
*B
=
A
How to use the ferrite core (Depending on model)
yUse the ferrite core to reduce the electromagnetic interference in the LAN cable. Wind the LAN
cable once on the ferrite core. Place the ferrite core close to the TV.
[Cross Section of Ferrite Core]
[to the TV] [to an External device]
ASSEMBLING AND PREPARING
14
ENGLISH
Separate purchase
ENG
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***DP
Dual Play Glasses
AN-VC5**
Video Call Camera
Compatibility
AG-F***DP
Dual Play Glasses
AG-F***
Cinema 3D Glasses
AN-MR500
Magic Remote
AN-VC5**
Video Call Camera
LG Audio Device
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
AG-F***
Cinema 3D Glasses
LG Audio Device
UB82**
UB80**
• •
• •
• •
AN-MR500
Magic Remote
UB83**
•
•
ASSEMBLING AND PREPARING
15
Parts and buttons
UB80**, UB82**
Remote control and
Intelligent1 sensors
UB83**
Screen
Power Indicator
Screen
Speakers
Joystick Button
ENGENGLISH
2
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
1
Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2
Joystick Button - This button is located behind the TV screen.
Joystick Button
2
NOTE
yYou can set the power indicator light to on or off by selecting
OPTION
in the main menus.
Loading...