LG 60LN5420-TC Owner’s Manual
OWNER’S MANUAL
LED TV
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LN54**
LN565*
LA61**
P/NO : MFL67725403 (1302-REV01)
Printed in Korea
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3 SAFETY INSTRUCTIONS
8 Viewing 3D Imaging (Only 3D models)
9 INSTALLATION PROCEDURE
9 ASSEMBLING AND PREPARING
9 Unpacking
11 Separate purchase
12 Parts and buttons
13 Lifting and moving the TV
14 Setting up the TV
14 - Attaching the stand
15 Mounting on a table
17 Mounting on a wall
18 Tidying cables
19 MAKING CONNECTIONS
19 Antenna connection
20 HDMI connection
20 Component connection
21 Composite connection
21 USB connection
22 Headphone connection
22 Audio Connection
22 - Digital optical audio connection
23 MHL connection
34 OPEN SOURCE SOFTWARE NOTICE
34 EXTERNAL CONTROL DEVICE
SETUP
24 REMOTE CONTROL
26 USING THE USER GUIDE
27 MAINTENANCE
27 Cleaning your TV
27 - Screen, frame, cabinet and stand
27 - Power cord
27 TROUBLESHOOTING
28 SPECIFICATIONS
34 LICENSES
WARNING
If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
3
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/
or remote control in the
following environments:
- A location exposed to
direct sunlight
- An area with high humidity
such as a bathroom
- Near any heat source
such as stoves and other
devices that produce heat
- Near kitchen counters or
humidifiers where they can
easily be exposed to steam
or oil
- An area exposed to rain or
wind
- Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
Do not place the product
where it might be exposed to
dust.
This may cause a fire
hazard.
Mains Plug is the TV
connecting/disconnecting
device to AC mains electric
supply. This plug must
remain readily attached and
operable when TV is in use.
Do not touch the power plug
with wet hands. Additionally,
if the cord pin is wet or
covered with dust, dry the
power plug completely or
wipe dust off.
You may be electrocuted
due to excess moisture.
Make sure to connect Mains
cable to compliant AC mains
socket with Grounded earth
pin. (Except for devices
which are not grounded on
earth.) Otherwise possibility
you may be electrocuted or
injured.
Insert power cable plug
completely into wall socket
otherwise if not secured
completely into socket, fire
ignition may break out.
Ensure the power cord does
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
Do not place a heavy object,
or the product itself, on
power cables.
Otherwise, this may result in
fire or electric shock.
Bend antenna cable between
inside and outside building
to prevent rain from flowing
in.
This may cause water
damaged inside the Product
and could give an electric
shock.
When mounting TV onto wall
make sure to neatly install
and isolate cabling from
rear of TV as to not create
possibility of electric shock /
fire hazard.
Do not plug too many
electrical devices into a
single multiple electrical
outlet.
Otherwise, this may result in
fire due to over-heating.
Do not drop the product
or let it fall over when
connecting external devices.
Otherwise, this may result
in injury or damage to the
product.
ENGENGLISH
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
Keep the anti-moisture
packing material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing
can cause suffocation. Keep
it out of the reach of children.
Do not let your children climb
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
Dispose of used batteries
carefully to ensure that
a small child does not
consume them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
Do not insert any metal
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
Do not put or store
inflammable substances
near the product. There is
a danger of combustion/
explosion or fire due to
careless handling of the
inflammable substances.
Do not drop metallic objects
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
Do not spray water on the
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
Do not allow any impact,
shock or any objects to fall
into the unit, and do not drop
anything onto the screen.
You may be injured or the
product can be damaged.
Never touch this product or
antenna during a thunder or
lighting storm.
You may be electrocuted.
Never touch the wall outlet
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
Do not disassemble, repair
or modify the product at your
own discretion.
Fire or electric shock
accident can occur.
Contact the service centre
for check, calibration or
repair.
If any of the following
occur, unplug the product
immediately and contact
your local service centre.
- The product has been
impacted by shock
- The product has been
damaged
- Foreign objects have
entered the product
- The product produced
smoke or a strange smell
This may result in fire or
electric shock.
SAFETY INSTRUCTIONS
5
Unplug the TV from AC
mains wall socket if you do
not intend to use the TV
for a long period of time.
Accumulated dust can cause
fire hazard and insulation
deterioration can cause
electric leakage/shock/fire.
Apparatus shall not be
exposed to dripping or
splashing and no objects
filled with liquids, such as
vases, shall be placed on
the apparatus.
CAUTION
Install the product where no
radio wave occurs.
There should be enough
distance between an outside
antenna and power lines
to keep the former from
touching the latter even
when the antenna falls.
This may cause an electric
shock.
Do not install the product
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to
the product.
If you install the TV on a
stand, you need to take
actions to prevent the
product from overturning.
Otherwise, the product may
fall over, which may cause
injury.
If you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product. When
you install the set to use the wall mounting
bracket (optional parts), fix it carefully so as not
to drop.
Only use the attachments / accessories
specified by the manufacturer.
When installing the antenna,
consult with a qualified
service technician. If not
installed by a qualified
technician, this may create
a fire hazard or an electric
shock hazard.
We recommend that you
maintain a distance of
at least 2 to 7 times the
diagonal screen size when
watching TV.
If you watch TV for a long
period of time, this may
cause blurred vision.
Only use the specified type
of battery.
This could cause damage to
the remote control.
Do not mix new batteries
with old batteries.
This may cause the batteries
to overheat and leak.
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in
charging device.
Make sure there are no
objects between the remote
control and its sensor.
Signal from Remote Control
can be interrupted due to
external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting
or darken viewing area.
When connecting external
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product
may fall over, which may
cause injury or damage the
product.
Do not turn the product
On/Off by plugging-in or
unplugging the power plug to
the wall outlet. (Do not use
the power plug for switch.)
It may cause mechanical
failure or could give an
electric shock.
ENGENGLISH
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
Please follow the installation
instructions below to
prevent the product from
overheating.
- The distance between the
product and the wall should
be more than 10 cm.
- Do not install the product in
a place with no ventilation
(e.g., on a bookshelf or in
a cupboard).
- Do not install the product
on a carpet or cushion.
- Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
Take care not to touch the
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on
the power plug pins or outlet.
This may cause a fire
hazard.
Protect the power cord from
physical or mechanical
abuse, such as being
twisted, kinked, pinched,
closed in a door, or walked
upon. Pay particular
attention to plugs, wall
outlets, and the point where
the cord exits the appliance.
Do not press strongly upon
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it, as it may
cause damage to screen.
Avoid touching the screen or
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary or permanent
distortion/damage to screen.
When cleaning the product
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation,
corrosion or breakage).
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
When unplugging the cable,
grab the plug and unplug it,
by pulling at the plug. Don’t
pull at the cord to unplug the
power cord from the power
board, as this could be
hazardous.
When moving the product,
make sure you turn the
power off first. Then, unplug
the power cables, antenna
cables and all connecting
cables.
The TV set or power cord
may be damaged, which
may create a fire hazard or
cause electric shock.
When moving or unpacking
the product, work in pairs
because the product is
heavy.
Otherwise, this may result in
injury.
Contact the service centre
once a year to clean the
internal parts of the product.
Accumulated dust can cause
mechanical failure.
Refer all servicing to
qualified service personnel.
Servicing is required when
the apparatus has been
damaged in any way, such
as power supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus,
the apparatus has been
exposed to rain or moisture,
does not operate normally,
or has been dropped.
If the product feels cold to
the touch, there may be
a small “flicker” when it is
turned on. This is normal,
there is nothing wrong with
product.
The panel is a high
technology display product
with resolution of two million
to six million pixels. You
may see tiny black dots and/
or brightly coloured dots
(red, blue or green) at a
size of 1 ppm on the panel.
This does not indicate a
malfunction and does not
affect the performance and
reliability of the product.
This phenomenon also
occurs in third-party
products and is not subject
to exchange or refund.
You may find different
brightness and colour of the
panel depending on your
viewing position(left/right/
top/down).
This phenomenon occurs
due to the characteristic
of the panel. It is not
related with the product
performance, and it is not
malfunction.
SAFETY INSTRUCTIONS
Displaying a still image (e.g., broadcasting
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking.
The warranty does not cover the product for
image sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
Generated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
7
ENGENGLISH
8
SAFETY INSTRUCTIONS
ENGLISH
ENG
Viewing 3D Imaging (Only 3D
models)
WARNING
Viewing Environment
Viewing Time
- When watching 3D contents, take 5 - 15 minute
breaks every hour. Viewing 3D contents for
a long period of time may cause headache,
dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
Some users may experience a seizure or other
abnormal symptoms when they are exposed to a
ashing light or particular pattern from 3D contents.
Do not watch 3D videos if you feel nausea, are
pregnant and/ or have a chronic illness such as
epilepsy, cardiac disorder, or blood pressure disease,
etc.
3D Contents are not recommended to those who
suffer from stereo blindness or stereo anomaly.
Double images or discomfort in viewing may be
experienced.
If you have strabismus (cross-eyed), amblyopia (weak
eyesight) or astigmatism, you may have trouble
sensing depth and easily feel fatigue due to double
images. It is advised to take frequent breaks than the
average adult.
If your eyesight varies between your right and left
eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or
refraining from watching 3D contents
Do not watch 3D contents when you feel fatigue from
lack of sleep, overwork or drinking.
When these symptoms are experienced, stop using/
watching 3D contents and get enough rest until the
symptom subsides.
- Consult your doctor when the symptoms persist.
Symptoms may include headache, eyeball
pain, dizziness, nausea, palpitation, blurriness,
discomfort, double image, visual inconvenience
or fatigue.
CAUTION
Viewing Environment
Viewing Distance
- Maintain a distance of at least twice the screen
diagonal length when watching 3D contents.
If you feel discomfort in viewing 3D contents,
move further away from the TV.
Viewing Age
Infants/Children
- Usage/ Viewing 3D contents for children under
the age of 5 are prohibited.
- Children under the age of 10 may overreact
and become overly excited because their vision
is in development (for example: trying to touch
the screen or trying to jump into it. Special
monitoring and extra attention is required for
children watching 3D contents.
- Children have greater binocular disparity of 3D
presentations than adults because the distance
between the eyes is shorter than one of adults.
Therefore they will perceive more stereoscopic
depth compared to adults for the same 3D
image.
Teenagers
- Teenagers under the age of 19 may react with
sensitivity due to stimulation from light in 3D
contents. Advise them to refrain from watching
3D contens for a long time when they are tired.
Elderly
- The elderly may perceive less 3D effect
compared to the youth. Do not sit closer to the
TV than the recommended distance.
Cautions when using the 3D glasses
Make sure to use LG 3D glasses. Otherwise, you
may not be able to view 3D videos properly.
Do not use 3D glasses instead of your normal
glasses, sunglasses or protective goggles.
Using modied 3D glasses may cause eye strain or
image distortion.
Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
The 3D glasses are fragile and are easy to be
scratched. Always use a soft, clean piece of cloth
when wiping the lenses. Do not scratch the lenses of
the 3D glasses with sharp objects or clean/wipe them
with chemicals.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
<
<
9
NOTE
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
The available menus and options may differ from the input source or product model that you are using.
New features may be added to this TV in the future.
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned
off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced,
and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
Some models have a thin film attached on to the screen and this must not be removed.
ENGENGLISH
NOTE
The items supplied with your product may vary depending on the model.
Product specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm
width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your
TV’s USB port.
B
A
B
*A
10 mm
=
*B
18 mm
A
=
ENGLISH
ENG
10
ASSEMBLING AND PREPARING
Remote control and
batteries (AAA)
(See p.24, 25)
Stand Screws
3EA, P5 x 25
4EA, M4 x 14
(Only LN54**, LN565*)
(See p.14)
Bracket Screw
2EA, M4 x 8
(Only 32/42LA61**)
2EA, P4 x 8
(Only 50LA61**)
(See p.16)
Owner’s manual Cable holder
Desk-mount Screw
(2EA : Only LA61**)
(1EA : Only
32/37/39/42/47/50/
60LN54**, LN565*)
(See p.16)
Stand Body /
Stand Base
(Only LA61**)
(See p.14)
(Depending on model)
(See p.18)
Stand Screws
8EA, M4 x 14
(Only LA61**)
(See p.14)
Stand Body /
Stand Base
(Only LN54**, LN565*)
(See p.14)
Power Cord
Desk-mount Cable
2EA
(Only LA61**)
(See p.16)
Cinema 3D Glasses
The number of 3D glasses may differ depending
on the model or country.
(Only LA61**)
ASSEMBLING AND PREPARING
11
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***
Cinema 3D glasses
Compatibility
AG-F***
Cinema 3D glasses
AG-F***DP
Dual play glasses
LG Audio Device •
AG-F***DP
Dual play glasses
LG Audio Device
LA61** LN54**, LN565*
•
•
ENGENGLISH
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s
circumstances or policies.
Loading...