LG Electronics 60S DU-42PZ60H, 60R, 60S DU-50PZ60H, DU-42PZ70, DU-42PZ60 User Manual

...

Page 1

PLASMA TV

OWNER’S MANUAL

Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service.

Model Number : Serial Number :

MODELS:

DU-42PZ60/60A/60B/60C/60K/60R/60S DU-42PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-42PZ70/70A/70B/70C/70K/70R/70S DU-42PZ70H/70HA/70HB/70HC/70HK/70HR/70HS DU-50PZ60/60A/60B/60C/60K/60R/60S DU-50PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-50PZ70/70A/70B/70C/70K/70R/70S DU-50PZ70H/70HA/70HB/70HC/70HK/70HR/70HS

LG Electronics U.S.A., Inc.

Page 2

2 Plasma TV

Warning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-

tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

arning

Page 3

Owner’s Manual 3

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Safety Instructions

Page 4

4 Plasma TV

Safety Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Safety Instructions continued

Page 5

Owner’s Manual 5

Contents

After reading this manual, keep it handy for future reference.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connection Options . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Key Functions . . . . . . . . . . . . . .9

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10

External Equipment Connections . . . . . . . . . .11~15

Antenna Connection . . . . . . . . . . . . . . . . . . . . .11

VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12

External A/V Source Setup . . . . . . . . . . . . . . . .13

Monitor Out Setup / DVD Setup . . . . . . . . . . . .13

HDSTB Setup / Digital Audio Output . . . . . . . . .14

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Operation

Screen Setup for PC mode

Adjustments for screen position, clock, and phase

. .16

Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .17

On-screen Menus Language Selection . . . . . . . . .17

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .18

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .18

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .19

Channel Label Setup . . . . . . . . . . . . . . . . . . . .19

Main Picture Source Selection . . . . . . . . . . . . .20

Front LED (Light Emitting Diode) Display . . . . .20

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Picture Control (User Option) . . . . . . . .21

Color Temperature Control . . . . . . . . . . . . . . . .21

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .22

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22

Manual Sound Control (User Option) . . . . . . . .22

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .23

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .23

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .24

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .24

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .24

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .25

Option Menu Features

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Caption / Caption Mode . . . . . . . . . . . . . . . . . .27

Caption Option / EZ Demo . . . . . . . . . . . . . . . .28

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .28

White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31

PIP (Picture-in-Picture)/Twin Picture

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..32

Selecting an Input Signal Source for PIP/Twin Picture

. .32

Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .32

TV Program Selection for PIP . . . . . . . . . . . . . .32

Moving the PIP sub picture . . . . . . . . . . . . . . . .33

Adjusting Main and Sub Picture Sizes for Twin Picture . .33 POP (Picture-out-of-Picture: Channel Scan) . . .33

External Control Device Setup . . . . . . . . . . . . . . . .34~38

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40

Programming the Remote . . . . . . . . . . . . . . . . . . . . . .41

Programming Codes . . . . . . . . . . . . . . . . . . . . . . .42~43

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .44

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48

Contents

Setup and Operation Checklist

Setup and Operation Checklist (See pages 11~15 for available connection and operational setup options.)

1. Unpack TV and all accessories.

2. Connect all external video and audio equipment. see pages 12 ~ 14.

3 Install batteries in remote control.

See page 9.

4. Turn TV on. See page 17.

5. Turn video source equipment on.

6. Select viewing source for TV. See page 20.

7. Fine-tune source image and sound to your personal preference or as required by source. See pages 21 ~ 23.

8. Additional features set up See Contents above.

Page 6

6 Plasma TV

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

Page 7

Owner’s Manual 7

Introduction

Controls

S-VIDEO VIDEO AUDIO

L/MONO

TV/VIDEO

VOL

ON/OFF

A/V INPUT 2

Power Button

S-VIDEO Input

A connection available to provide better picture quality than the video input.

VIDEO Input

Connects the video signal from a video device.

AUDIO Input

Use to connect to hear stereo sound from an external device.

TV/VIDEO Button

VOLUME (F,G) Buttons

Power Standby Indicator

Illuminates red in standby mode, Illuminates green when the TV is turned on.

- This is a simplified representation of front panel. Here shown may be somewhat different from your TV.

- This manual explains the features available on the DU-50PZ60/70 series TVs.

Remote Control Sensor

CHANNEL (E, D) Buttons

MENU Button

Front Panel Controls

Page 8

8 Plasma TV

Introduction

Connection Options

RGB INPUT

Antenna1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AC INPUT

EXTERNAL SPEAKER

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

(MONO)

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

RS-232C INPUT

(CONTROL/SERVICE)

Back Connection Panel

Antenna 1-2 Inputs

Connect cable or antenna signals to the TV, either directly or through your cable box. For DTV use Antenna 2 only.

RGB Input/Audio Input/DVI Input

Connect the monitor output connector from a PC to the appropriate input port.

Digital Audio (DVI: Digital Visual

Interface/Component1) Input/

Digital Audio Output

Connect digital audio from various types

of equipment. Note: In standby mode,

these ports will not work.

Audio/Video Input 1

Connect audio/video output from an

external device to these jacks.

DVD/DTV Input (Component 1-2)

Connect a component video/audio device to these jacks.

Monitor Output

Connect a second TV or

Monitor.

Remote Control Port

Connect your wired remote control here.

S-Video Input

Connect S-Video out from an S-VIDEO device to the S-VIDEO input.

External Speaker (8 ohm Output)

Connect to optional external speaker(s).

* For further information, refer to ‘Speaker &

Speaker Stand’ manual.

Power Cord Socket

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

ate the TV on DC power.

- This manual explains the features available on the DU-50PZ60/70 series TVs.

Page 9

Owner’s Manual 9

Installation

- When using the remote control, aim it at the remote control sensor on the TV.

LIGHT

TV/VIDE

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

SOUND VIDEO

EXIT

PLAY PAUSE STOP RECORD

PIP PIPCH- PIPCH+ PIPINPUT

FREEZE

ADJUST

ZOOM SIGNAL SWAP

REW FF SKIP

POWER

TIM

FLASHBK

LIGHT

Illuminates the remote control buttons.

TV/VIDEO

Selects: DTV, Analog, Video1-2,

Component 1-2, RGB-DTV (or RGB-PC),

DVI-DTV (or DVI-PC) input sources.

COMP/RGB/DVI

Selects: Component 1-2, RGB-DTV (or RGB-

PC), DVI-DTV (or DVI-PC) input sources.

NUMBER buttons

DASH

Used to enter a program number for multiple

program channels such as 2—1,2—2,etc.

MUTE

Switches the sound on or off.

VCR/DVD BUTTONS

Control some video cassette recorders or DVD player ("RECORD" button is not available for DVD player).

RATIO

Changes the aspect ratio.

MODE

Selects the remote operating mode: TV, VCR, DVD, CABLE, HDSTB or AUDIO. Select other operating modes, for the remote to operate external devices.

POWER

Turns your TV or any other programmed equipment on or off, depending on mode.

TIMER

Lets you select the amount of time before your TV turns itself off automatically.

SURF

Use to scroll the Surf channel list.

Select a closed caption: Off, EZ Mute, and On.

FLASHBK

Tunes to the last channel viewed.

THUMBSTICK (Up/Down/Left/Right/OK)

Allows you to navigate the on-screen

menus and adjust the system settings to

your preference.

CHANNEL UP/DOWN

Selects available channels found with EZ scan.

EXIT

Clears all on-screen displays and returns to TV viewing from any menu.

VIDEO

Adjusts the factory preset picture according to the room.

VOLUME UP/DOWN

Increases/decreases the sound level.

SAP

Selects MTS sound: Mono, Stereo, and SAP.

Change the audio language in DTV mode.

Brings up the main menu to the screen.

INFO

When you watch the TV, displays information

on top of the screen. Not available in

Component 1-2, RGB and DVI mode.

SOUND

Selects the sound appropriate

for the program's character.

PIP

Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes.

PIPCH-/PIPCH+

Changes to next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the PIP/main images.

FREEZE

Freezes the currently-viewed picture. Main

picture is frozen in PIP/Twin picturre mode.

ADJUST

Adjusts screen position, clock, and

phase in PC mode.

ZOOM

Enlarges the main picture size.

SIGNAL

Displays the digital signal strength.

Installing Batteries

• Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -).

• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.

Replace cover.

Remote Control Key Functions

Page 10

10 Plasma TV

Installation

Owner’s Manual

1.5V

Batteries

Power Cord

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

SOUNDVIDEO

EXIT

PLAY PAUSE STOP RECORD

PIP PIPCH- PIPCH+PIPINPUT

FREEZE

ADJUST

ZOOM SIGNAL SWAP

REW FF SKIP

O W

E R

TI M

E R

FLASHBK

Remote Control

75Ω Round Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

Installation Instructions

• The TV can be installed in various ways such as on a wall, or on a desktop etc.

• The TV is designed to be mounted horizontally. The speakers shown are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.

4 inches

4 inches4 inches

2 inches

4 inches

2 inches

4 inches

2.36 inches

Page 11

Owner’s Manual 11

Installation

- Antenna or Cable Service without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed.

Antenna Connection

Analog and Digital TV signals provided on one antenna

NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.

The TV will let you know when the analog, cable, and digital channel scans are complete.

Analog and Digital TV signals provided on two separate antennas

• In a poor signal area to improve picture quality, purchase and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your dealer for assistance.

RGB INPUT

AUDIO INPUT

DVI INPUT

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT1 INPUT

OUTPUT

(

)

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Outdoor

Antenna

Wall Antenna Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

RGB INPUT

Antenna1 Antenna 2

AUDIO INPUT

DVI INPUT

Wall Antenna Socket

RF Coaxial Wire (75 ohm)

Analog Antenna

Digital Antenna

Bronze Wire

Turn clockwise to tighten.

Wall Antenna Socket

RF Coaxial Wire (75 ohm)

Plasma TV

External Equipment Connections

Antenna 2

RGB INPUT

AUDIO INPUT

DVI INPUT

DVI

COMPONENT1

OUTPUT

INPUT

DIGITAL AUDIO

OPTICAL

Amplifier

Signal

Page 12

12 Plasma TV

Installation

NOTE: All cables shown are not included with the TV

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

Connection Option 1

Set VCR output switch to 3 or 4 and then tune

TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)

Do not connect to both Video and S-Video at the same time.

VCR Setup

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

Connection Option 1

1. Select 3 or 4 with channel switch on cable box.

2. Tune the TV channel to the same selected output channel on cable box.

3. Select channels at the cable box or with the cable box remote control.

Connection Option 2

1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

2. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)

3. Select your desired channel with the remote control for cable box.

Cable

TV Setup

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

VCR

RF Cable

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

VCR

Cable Box

Page 13

Owner’s Manual 13

Installation

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

How to connect

Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source).

2. Operate the corresponding external equipment. Refer to external equipment operating guide.

Component ports

on the TV

Video output ports on DVD player

Y Y Y Y

B-Y

Cb PB

R-Y

Cr P

How to connect

1. Connect the DVD video outputs (Y, P

B, PR) to the COMPONENT (Y,

PB, PR

) INPUT jacks on the TV and connect the DVD audio outputs to

the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the SVIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

NOTE: If your DVD player does not have component video output, use

S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video 1 or Video 2 external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

A/V Source Setup

DVD Setup

AUDIO VIDEO

S-VIDEO

REMOTE CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

RL R L

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

S-VIDEO

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

S-VIDEO

RS-232C INPUT

(CONTROL/SERVICE)

DVD

Camcorder

Video Game Set

The TV has a special signal output capability which allows you to hook up a second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.

NOTE

• Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input sources cannot be used for Monitor out.

NOTES

• Digital Audio will not work for Component 2 input source.

• Digital Audio operation has priority if Digital Audio and AUDIO L/R

are connected at the same time.

S-VIDEO

(R) AUDIO (L) VIDEO

S-VIDEO

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1

INPUT

OUTPUT

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

Monitor Out Setup

Page 14

14 Plasma TV

Installation

Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio Optical Output port.

2. Connect the other end of the optical cable to the digital audio optical input on the audio equipment.

3. Set the “

TV Speaker option - Off” in the AUDIO menu. Refer to

page 23. See the external audio equipment instruction manual for operation.

Caution: Do not look into the optical output port.

Looking at the laser beam may damage your vision.

Digital

Audio Output

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.

How to connect

Use the TV’s COMPONENT (Y, P

B, P

R) INPUT, RGB or DVI jack for

video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to select Component 1, Component 2, RGB-DTV, or DVI-DTV source.

HDSTB Setup

RGB INPUT

Antenna1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AC INPUT

EXTERNAL SPEAKER

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

(MONO)

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

RS-232C INPUT

(CONTROL/SERVICE)

(R) AUDIO (L)

RGB-DTV OUTPUT

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

DVI-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

Digital Set-top Box

or or

RGB INPUT

AUDIO INPUT

DVI INPUT

AUDIO INPUT VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

COMPONENT1 INPUT

OUTPUT

Signal 480i 480p 720p 1080i

Component 1/2

Yes Yes Yes Yes

RGB-DTV,DVI-DTV

No Yes Yes Yes

Page 15

Owner’s Manual 15

Installation

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Use the TV’s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector.

• If the graphic card on the PC does not output

analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV.

• If the graphic card on the PC does output analog

and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Select RGB-PC or DVI-PC input source in main input option of SETUP menu. (Refer to P.20)

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.

• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become per-

manently imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

PC Setup

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

AUDIO INPUT VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

COMPONENT1 INPUT

OUTPUT

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for the graphic card accordingly.

Resolution

640x350

720x400

640x480

800x600

Horizontal

Frequency(KHz)

31.468

37.861

31.469

37.927

31.469

37.861

37.500

43.269

70.09

85.08

70.08

85.03

59.94

72.80

75.00

85.00

35.156

37.879

48.077

46.875

53.674

48.363

56.476

60.023

56.25

60.31

72.18

75.00

85.06

60.00

70.06

75.02

Vertical

Frequency(Hz)

Resolution

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1024x768

Monitor Display Specifications (RGB-PC / DVI-PC Mode)

Page 16

16 Plasma TV

Installation

Operation

- Be sure to select the RGB-PC/RGB-DTV source before operation. (For RGB-DTV input source, Position and Reset are available.)

- In DVI-PC and DVI-DTV input source, settings are not adjustable.

- You can manually adjust picture position and minimize image shaking for the PC input source.

1. Press the ADJUST button and then use

D / E

button to select POSITION,

CLOCK, or PHASE.

2. Press OK button and then use

D / E

/ F /

buttons to make appropriate adjust-

ments.

• The PHASE adjustment range is -16 ~ +16.

• The CLOCK adjustment range is -30 ~ +30.

3. Press OK button.

Adjustment for screen Position, Clock, and Phase

Screen Setup for PC mode

1. Press the ADJUST button and then use

D / E

button to select the RESET option.

2. Press OK button and then use

F / G

button to select Yes .

3. Press OK button

Initializing (Reset to original factory values)

- To initialize the adjusted values

POSITION

CLOCK

PHASE

RESET

Adjust

POSITION

CLOCK

PHASE

RESET

Adjust

Initialize Settings

Page 17

Owner’s Manual 17

Operation

On-screen Menus Language Selection

TTurning the TV On

urning the TV On

Turning on the TV just after installation

Turning on the TV (power cord is still connected)

1. Connect power cord correctly.

2. Press the ON/OFF button on the TV. At this moment, the TV is switched to standby mode.

Press the TV/VIDEO, CH (

D/ E

) button on the TV or press the POWER, TV/VIDEO,

COMP/RGB/DVI, CH (+

-), Number (0 ~ 9) button on the remote control and then the TV will

switch on.

• Press the ON/OFF button on the TV to turn the TV on.

1. If the TV was turned off with the ON/OFF button on the TV

2. If the TV was turned off with the remote control and then the ON/OFF button on the TV

• Press the ON/OFF button on the TV and then press the POWER, TV/VIDEO, COMP/RGB/DVI, CH (+

-), Number (0 ~ 9) button on the remote control to turn the TV on.

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use

D/ E

button to select the OPTION menu.

2. Press the Gbutton and then use

D/ E

button to select Language.

3. Press the Gbutton and then use

D/ E

button to select your desired language.

From this point on, the on-screen menus will be shown in the selected language.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

NOTE

• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

English

Español

Français

Page 18

18 Plasma TV

Operation

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Select antenna input,

press

Air

ANT 1 ANT 2

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

button and then use

D / E

button to select EZ Scan.

3. Press the

button and then use

D / E

button to select antenna input (Based on your connections to antenna 1-2).

• Analog/DTV Air: Watching the Over-the-air, cable, and digital over-the-air signals via antenna 1 input port

• Analog/DTV Cable: Watching the Over-the-air, cable, and digital cable signals via antenna 1 input port

• Analog+DTV Air (ANT2): Watching the Over-the-air, and cable signal via antenna 1 input port and the digital over-the-air signal via antenna 2 input port

• Analog/DTV Cable (ANT2): Watching the Over-the-air, and cable signa lvia antenna 1 input port and the digital cable signal via antenna 2 input port

* Cable Service Band Note: Select Std=Standard, HRC=HRC Band, or IRC=IRC Band.

(For further band information, contact your cable service provider.)

4. Press the OK button to begin the channel search.

Allow EZ Scan to complete the channel search cycle for TV, CATV, and DTV/CADTV.

EZ Scan (Channel Search)

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

Selection ( Gor ) leads you

to the channel edit screen.

- Create two different types of channel lists in memory: “Custom list” and “Surf" (Favorite) channel list” from the default channel list created from the EZ Scan channel search.

- A custom list can be created by toggling each channel on or off with OK button. Once a channel is highlighted, you will be able to see whether the channel is currently added or deleted by referring to the small window at the top-left corner of the screen. You can create your own Surfchannel list with up to 10 channels. It appears at the bottom-left corner of the screen. Use the SURF button on the remote control when a channel is highlighted, to add or delete the channel from the Surf channel list.

- You can create your SURF channel list from the channel list memorized from EZ Scan.

- CATV is available for 1-125 channel.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

button and then use

D / E

button to select Ch. Edit.

3. Press the

button. You will now see a screen filled with channel numbers and

a preview picture.

4. Use

D / E

/ F /

button to select a channel and then use the OK button to add

or delete it. Press SURF to add the channel to the Surf List.

5. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Channel Edit

Setup Menu Options

Analog/DTV Air

Analog/DTV Cable

Analog+DTV Air(ANT2)

Analog+DTV Cable(ANT2)

Prev.

Select antenna input,

press

Cable

ANT 1 ANT 2

Analog/DTV Air

Analog/DTV Cable

Analog+DTV Air(ANT2)

Analog+DTV Cable(ANT2)

Prev.

Select antenna input,

press

Cable Air

ANT 1 ANT 2

Analog/DTV Air

Analog/DTV Cable

Analog+DTV Air(ANT2)

Analog+DTV Cable(ANT2)

Prev.

Select antenna input,

press

Air Cable

ANT 1 ANT 2

Analog/DTV Air

Analog/DTV Cable

Analog+DTV Air(ANT2)

Analog+DTV Cable(ANT2)

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

Select DTV cable band,

press

1. STD

2. HRC

3. IRC

Page 19

Owner’s Manual 19

Operation

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

Selection ( Gor ) leads you

to the channel logo screen.

- Choose preset labels for your channels.

- If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a DTV channel - even if you didn't preset a label for the channel.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press theGbutton and then use

D / E

button to select Ch.Label.

3. Press the

button. You will now see a screen filled with Labels and a preview screen.

4. Use the CH +/- button to select a channel to Label.

5. Use

D / E

/ F /

button to select the appropriate label for the channel, then press OK button to set the Label to the

selected channel.

6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Channel Label Setup

- Reveals how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation.

- Digital DTV Signals: May not be available in all areas, nor are broadcast on all programs.

1. Press the SIGNAL button.

2. View the on-screen signal strength monitor to see the quality of the signal being received.

• You can also check the

DTV Signal strength with the SETUP menu.

DTV Signal Strength

Page 20

20 Plasma TV

Operation

Setup Menu Options continued

- Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

button and then use

D / E

button to select Main Input.

3. Press the

button and then use

D / E

button to select the source: DTV, Analog, Video1, Video2, Component1, Component2, RGB-DTV (or RGB-PC), DVI-DTV (or DVI-PC).

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Main Picture Source Selection

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

DTV

Analog

Video1

Video2

Component1

Component2

RGB-DTV

DVI-DTV

- Illuminates brightly when the set is turned on. The LED displays current TV status.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

button and then use

D / E

button to select Front Display.

3. Press the

button and then use

D / E

button to select Off, Dark, Normal, and

Bright.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Front LED (Light Emitting Diode) Display

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

Off

Dark

Normal

Bright

Page 21

Owner’s Manual 21

Operation

- Adjust the picture appearance to suit your preference and viewing situations.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press theGbutton and then use

D / E

button to select the desired picture option (

Contrast, Brightness, Color, Sharpness, or Tint).

3. Press the

button and then use

F / G

button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below:

Off (your own settings), Normal, Digital Preset, Night Time, Movie, Weak Signal, Video Game, and Sports.

• You can also use the VIDEO menu to adjust EZ Picture.

2. Press the EXIT button to save and return to TV viewing.

EZ Picture

Manual Picture Control (

Manual Picture Control (Off

option)

- Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the

button and then use

D / E

button to select Color Temperature .

3. Press theGbutton and then use

D / E

button to select either Warm, Medium,

Cool.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Color

Color TT

emperature Control

- Use to quickly reset all the Video menu options to their original factory preset values.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the Gbutton and then use

D / E

button to select Video Preset .

3. Press the

button to reset the Video menu options to original values.

VVideo Preset

ideo Preset

- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category.

- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Off.

Normal, Digital Preset, Night Time, Movie, Weak Signal, Video Game, and Sports settings are preset for opti-

mum picture quality at the factory and are not adjustable.

VVideo Menu Options

ideo Menu Options

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Picture

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature

Video Preset

Warm

Medium

Cool

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Picture

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature

Video Preset

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Picture

Contrast 85

Brightness 50

Color 50

Sharpness 50

Tint 0

Color Temperature

Video Preset

Selection ( Gor ) presets

the video configuration.

R G

Page 22

22 Plasma TV

Operation

- Other languages may be available if a digital signal is provided by the broadcasting station.

Audio Menu Options

1. Press the SOUND button repeatedly to select the appropriate sound setup as shown below:

Off (your own settings), Normal, Stadium, Theater, and Music.

• You can also adjust EZ Sound in the AUDIO menu.

2. Press EXIT button to save and return to TV viewing.

EZ Sound

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

button and then use

D / E

button to select the desired sound option

(Balance, Treble, or Bass).

3. Press the

button and then use

F / G

button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Manual Sound Control (

Manual Sound Control (Off

option)

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press theGbutton and then use

D / E

button to select Audio Language.

3. Press the

button and then use

D / E

button to select: English, Spanish, or

French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Audio Language

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Off.

Normal, Stadium, Theater, and Music are preset for good sound quality at the factory and are not adjustable.

- Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the Gbutton and then use

D / E

button to select EZ SoundRite.

3. Press the

button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

EZ SoundRite

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

English

Spanish

French

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

Off

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Audio Language

EZ SoundRite

EZ Sound

Balance 0

Treble 50

Bass 50

Front Surround

TV Speaker

L R

- Adjust the sound to suit your taste and room situations.

Page 23

Owner’s Manual 23

Operation

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

Off

3D EchoSound System

SRS TruSurround XT

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

Off

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the Gbutton and then use

D / E

button to select Front Surround.

3. Press the

button and then use

D / E

button to select Off, 3D EchoSound

System

or SRS (Sound Retrieval System) TruSurround XT..

• SRS TruSurround XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material.

• 3D EchoSound System Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into stereo sound.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Front Surround

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

button and then use

D / E

button to select TV Speaker.

3. Press the

button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

TV Speakers On/Of

f Setup

- Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off.

1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button,

Mono,

Stereo, or SAP appear in turn.

• If other languages available on the digital signal, select them with the SAP button.

2. Press EXIT button to save and return to TV viewing.

Stereo/SAP

Broadcasts Setup

- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.

- Stereo or SAP can be received only when the TV station transmits those signals even though you have selected Stereo or SAP.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.

- is a trademark of SRS Labs, Inc.

- TruSurround XT technology is incorporated under license from SRS Labs, Inc.

- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Page 24

24 Plasma TV

Operation

TTime Menu Options

ime Menu Options

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Off

Time Zone Eastern

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Off

Time 6 : 30 AM

Ch. TV 2-0

Vol 17

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Year - - - -

Date - - / - -

Time - - : - - - -

- Timer function operates only if current time has been set.

- Off-Timer function overrides On-Timer function if they are set both set to the same time.

- The TV must be in standby mode for the On-Timer to work.

- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.

On/Of

On/Off f TT

imer Setup

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

button and then use

D / E

button to select Off Timer or On Timer.

3. Press the Gbutton and then use

D / E

button to select On.

• To cancel

On/Off timer function, select Off.

4. Press the Gbutton and then use

D / E

button to set the hour.

5. Press the

button and then use

D / E

button to set the minutes.

6. For only

On timer function

Press the

button and then use

D / E

button to select the channel at turn-on.

Press the

button and then use

D / E

button to set the sound level at turn-on.

7. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Auto Clock Setup

- The time is set automatically from a digital channel signal.

- The digital channel signal includes information for the current time provided by the broadcasting station.

- Set the clock manually, if the current time is set incorrectly by the auto clock function.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

button and then use

D / E

button to select Auto Clock.

3. Press the

button and then use

D / E

button to select On.

4. Press the Gbutton and then use

D / E

button to select your viewing area time

zone:

Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.

5. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Manual Clock Setup

- If current time setting is wrong, reset the clock manually.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

button and then use

D / E

button to select Manual Clock.

3. Press the

button and then use

F / G

button to select either the year, date, or

time option. Once selected, use the

D / E

button to set the year, date, and time

options.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Page 25

Owner’s Manual 25

Operation

Auto Of

Auto Offf

- If set to on and there is no input signal, the TV turns off automatically after 10 minutes.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

button and then use

D / E

button to select Auto Off.

3. Press the

button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Sleep

Sleep TT

imer

- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.

- You can also set up the

Sleep Timer in the TIME menu.

1. Press the TIMER button repeatedly to select the number of minutes. First the

Off option appears on the screen,

followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count

down from the number of minutes selected.

3. To check the remaining minutes before the TV turns off, press the TIMER button once.

4. To cancel the Sleep Timer, press the TIMER button repeatedly to select

Off.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Off

Page 26

26 Plasma TV

Operation

Option Menu Features

Aspect Ratio Control

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed.

- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.

- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/DVI-DTV (720p/1080i)/DTV(720p/1080i) input source.

- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.

- Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and

remain visible.

•

Set By Program

Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9)

• 4:3

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides.

• 16:9

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

• Horizon

Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

• Zoom 1

Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

• Zoom 2

Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage.

• Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted.

You can adjust the enlarge proportion of Cinema Zoom using

D / E

button. The adjustment range is 1~16.

1. Press the RATIO button repeatedly to select the desired picture format.

You can also adjust

Aspect Ratio in the OPTION menu.

Page 27

Owner’s Manual 27

Operation

Caption Mode

Analog Broadcasting System Captions

- Select a caption mode for displaying captioning information if provided on a program.

- Analog caption displays information at any position on the screen usually the program's dialog.

- Text displays information, usually at the bottom position and is used for a data service, generally not program related.

- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna 1 source.

- This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

CC 1

CC 2

CC 3

CC 4

Text 1

Text 2

Text 3

Text 4

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

English

Spanish

French

Digital Broadcasting System Captions

- Choose the language you want the DTV/CADTV Captions to appear in.

- Languages can be chosen for digital sources only if they are included on the program.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

button and then use

D / E

button to select Caption Mode.

3. Press the

button and then use

D / E

button to select caption: CC1, CC2, CC3,

CC4, Text1, Text2, Text3, or Text4.

• CAPTION

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

• TEXT

The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

button and then use

D / E

button to select Caption Mode.

3. Press the

button and then use

D / E

button to select available caption lan-

guages: English, Spanish, or French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Caption

1. Use the CC button repeatedly to select Caption Off, EZ Mute, or On.

• EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

. • You can also use the OPTION menu to select Caption.

2. Press EXIT button to save and return to TV viewing.

Page 28

28 Plasma TV

Operation

Option Menu Features continued

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

Style Custom

Size A Standard

Font Font 0

Text Color White

Text Opacity Solid

Bg Color Black

Bg Opacity Solid

Edge Type None

Edge Color Black

Caption Option

- Customize the DTV/CADTV captions that appear on your screen.

1. Press the MENU button and then use

D / E

button to select the OPTION

menu.

2. Press the

button and then use

D / E

button to select Caption Option.

3. Press the

button and then use

F / G

button to select Custom.

4. Use

D / E

button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.

• Size: Set the size the words will appear in.

• Font: Select a typeface for the words.

• Text Color: Choose a color for the text.

• Text Opacity: Specify the opacity for the text color.

• Bg (Background) Color: Select a background color.

• Bg (Background) Opacity: Select the opacity for the background color.

• Edge Type: Select an edge type.

• Edge Color: Select a color for the edges.

5. Press EXIT button to return to TV viewing or press MENU button to return

to the previous menu.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

EZ Demo

- Shows you how to navigate the TV's on-screen menus.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

button and then use

D / E

button to select EZ Demo.

3. Press the

button to start EZ Demo. Press EXIT button to stop EZ Demo.

Selection ( Gor )

leads you to the

EZ Demo.

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen for a long period of time.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the Gbutton and then use

D / E

button to select ISM Method.

3. Press the Gbutton and then use

D / E

button to select either Normal, Orbiter,

Inversion.

• Normal If image sticking is never a problem, ISM is not necessary - set to Normal.

• Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per minute: Right → Right → Downside → Downside → Left → Left → Upside → Upside.

• Inversion Inversion will automatically invert the plasma display panel color every 30 minutes.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

ISM (Image Sticking Minimization) Method

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

Normal

Orbiter

Inversion

Page 29

Owner’s Manual 29

Operation

Low Power

- Low power reduces the plasma display's power consumption.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

button and then use

D / E

button to select Low power.

3. Press the Gbutton and then use

D / E

button to select On or Off.

• If you select On, the screen darkens.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

- White Wash removes permanent images from the screen.

- Set White Wash ‘

ON’ until fixed image disappears.

- Note: An excessive permanent image may be impossible to clear entirely with White Wash.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

button and then use

D / E

button to select White wash.

3. Press the

button and then use

D / E

button to select On or Off.

• When you select On, the screen changes to white.

4. To return to normal viewing, press the any button.

White W

ash

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

Off

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Aspect Ratio

Caption

Caption Mode

Caption Option

Language

EZ Demo

ISM Method

White Wash

Low Power

Off

1. Press the ZOOM button in DTV 720p, or 1080i modes.

2. Use the

D / E

/ F /

buttons to select the screen split zoom section.

3. To return to normal viewing, press the ZOOM button again.

Split Zoom (DTV 720p, or 1080i mode only)

- Enlarges the picture with correct proportions.

- When enlarging the picture, the image may become distorted.

Page 30

30 Plasma TV

Operation

Lock Menu Options

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enablethe lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters:

Movie Ratings :

• Blocking Off (Permits all programs)

• G (General audience)

• PG (Parental guidance suggested)

• PG-13 (Parents strongly cautioned)

• R (Restricted)

• NC-17 (No one 17 and under admitted)

• X (Adult only)

If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

• TV-G (General audience)

• TV-PG (Parental guidance suggested)

• TV-14 (Parents strongly cautioned)

• TV-MA (Mature audience only)

• TV-Y (All children)

• TV-Y7 (Children 7 years older)

TV Rating Children:

• Age (applies to TV-Y, TV-Y7)

• Fantasy Violence (applies to TV-Y7)

TV Rating General:

• Age (applies to TV-G, TV-PG, TV-14, TV-MA)

• Dialogue - sexual dialogue (applies to TV-PG, TV-14)

• Language - adult language (applies to TV-PG, TV-14, TV-MA)

• Sex - sexual situations (applies to TV-PG, TV-14, TV-MA)

• Violence (applies to TV-PG, TV-14, TV-MA)

Aux. Block

• Video 1, 2 (On, Off)

• Component 1, 2 (On, Off)

• RGB, DVI (On, Off)

Page 31

Owner’s Manual 31

Operation

Parental Lock Setup

1. Press the MENU button and then use

D / E

button to select the LOCK menu.

Then, press the Gbutton

• If Lock is already set, enter the password as requested.

• The TV is set up with the initial password “7-7-7-7”.

2. Use the

D /E

button to choose from the following Lock Menu options. Once the

option is selected, change the settings to your preference.

• Lock System: Activates or disables the blocking scheme you set up previ-

ously.

• Set Password: Change the password by inputting a new password twice.

• Movie Rating (MPPA): Blocks movies according to the movie ratings limits

specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

• TV Rating-Children: Prevents children from watching certain children's TV

programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.

• TV Rating-General: Based on the ratings, blocks certain TV programs that

you and your family do not want to view.

• Aux. Block: Enables you to select a source to block from the external

source devices you have hooked up.

3. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Note

• If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.

- Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu if the Lock System is turned on

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

Lock System

Set Password

Block Ch.

Movie Rating

TV Rating-Children

TV Rating-General

Aux. Block

Off

Page 32

32 Plasma TV

Operation

WWatching PIP/POP/T

atching PIP/POP/T

win Picture

- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image.

- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen.

- If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen.

Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.

PIP Off

PIP Mode POP Mode Twin Picture Mode

PIP

(Picture-In-Picture) / POP

/ T

win Picture

TV Program selection for PIP

1. Press the PIP button.

2. Select the Analog or DTV option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+

PIPCH- button to select a channel for the sub picture.

Swapping the PIP

Swapping the PIP/T/T

win Picture

Use the SWAP button to switch the main and sub pictures.

• Component 1, Component 2, RGB-PC (or RGB-DTV), DVI-DTV (or DVI-PC) input sources for the main picture can’t

be used to swap the main and sub pictures.

Selecting an Input Signal Source for PIP/T

win Picture

Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the Sub Input in the SETUP menu.

Main Picture Source

Available Sub Picture Sources

DTV Signal Analog Signal

Analog, Video 1, and Video 2 DTV, Analog, Video 1, and Video 2

Main Picture Sub Picture Main Picture Sub Picture

TV 2-0

TV 4-0

TV 6-0

Page 33

Owner’s Manual 33

Operation

Moving the PIP

sub picture

In PIP mode, press the

D / E

/ F /

button to move the sub picture to a different location on the

screen.

Adjusting Main and Sub Picture Sizes for

Adjusting Main and Sub Picture Sizes for TT

win Picture

Use the

D / E

/ F /

button to change main and sub picture sizes in Twin Picture mode.

If the maximal adjusted screen is 4:3, the large screen is filled with entire screen vertically as shown.

If the maximal adjusted screen is 16:9, the large screen appears the gray part at both the up and down sides.

i.e)

1. Press the PIP button to activate the POP mode while in PIP mode.

• Channel selection: Use

button to enlarge the selected channel being searched on the PIP

screen to shift it for viewing on the Main screen.

• PIP selection: Use

D / E

button to select one of 3 PIP screen pictures in POP mode.

• Input source selection for PIP: Use PIP INPUT button or Sub Input option on the SETUP

menu to select an input source for the sub picture (You can’t select DTV for main and sub picture simultaneously). You can only select the Analog and DTV signal for sub input source in POP mode.

2. Press the EXIT button to cancel POP mode.

POP

(Picture-out-of-Picture: Channel Scan)

- Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display, (while the main picture source remains the current channel). The pictures of all the programmed channels are searched with the 3 POP screen.

- Note: Run EZ Scan channel search before using POP mode.

TV 2-0

TV 4-0

TV 6-0

Page 34

34 Plasma TV

External Control Device Setup

No. Pin Name 1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection

2 3 5 4 6 7 8

RXD

TXD GND DTR DSR

RTS

CTS

TXD RXD GND DSR DTR CTS RTS

7-Wire Configurations

(Standard RS-232C cable)

D-Sub 9

3 2 5 6 4 8 7

PDP

D-Sub 9

2 3 5 4 6 7 8

RXD TXD

GND

DTR DSR RTS CTS

TXD RXD

GND

DTR DSR RTS CTS

3-Wire Configurations

(Not standard)

D-Sub 9

3 2 5 4 6 7 8

PDP

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor.

TType of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

External Control Device Setup

RS-232C Setup

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE CONTROL

AC INPUT

EXTERNAL SPEAKER

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

Page 35

Owner’s Manual 35

External Control Device Setup

Set ID

Use this function to specify a monitor ID number. Refer to ‘Real Data Mapping’. See page 36.

• Baud rate : 9600 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Communication Parameters

1. Press the MENU button and then use

D /E

button to select the SETUP menu.

2. Press the Gbutton and then use

D /E

button to select SET ID.

3. Press the Gbutton and then use

D /E

button to adjust SET ID to choose the

desired monitor ID number. The adjustment range of SET ID is 1 ~ 99.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

ransmission

[Command 1]: First command to control the set. (j or k)

[Command 2]: Second command to control the set.

[Set ID]: You can adjust the set ID to choose desired monitor

ID number in Setup menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.

[DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return

ASCII code ‘0x0D’

[ ]: ASCII code ‘space (0x20)’

[Command1][Command2][ ][Set ID][ ][Data][Cr]

TTransmission / Receiving Protocol

ransmission / Receiving Protocol

Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

[Command2][ ][Set ID][ ][OK][Data][x]

Error Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving abnormal data from non-viable functions or communication errors.

[Command2][ ][Set ID][ ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function 3: Wait more time

01. Power k a 0 ~ 1

02. Input Select k b 0 ~ 9

03. Aspect Ratio k c 0 ~ 15

04. Screen Mute k d 0 ~ 1

05. Volume Mute k e 0 ~ 1

06. Volume Control k f 0 ~ 64

07. Contrast k g 0 ~ 64

08. Brightness k h 0 ~ 64

09. Color k i 0 ~ 64

10. Tint k j 0 ~ 64

11. Sharpness k k 0 ~ 64

12. OSD Select k l 0 ~ 1

13.

Remote Control Lock Mode

k m 0 ~ 1

14. PIP/Twin k n 0 ~ 3

15. PIP Position k q 0 ~ 3

16. Treble k r 0 ~ 64

17. Bass k s 0 ~ 64

18. Balance k t 0 ~ 64

19. Color Temperature k u 0 ~ 2

20. PIP Input Source k y 0 ~ 3

21. Orbiter j p 0 ~ 2

22. White Wash j q 0 ~ 1

23. Orbiter Time Setting j r 1 ~ 64

24. Orbiter Pixel Setting j s 0 ~A

COMMAND 1 COMMAND 2 DATA

(Hexadecimal)

25. Channel Tuning m a 01 ~ 87 01 ~ 87 00 ~ FE 00 ~ 15

26. Channel Add/Del m b 00 ~ 01

27. Key m c

COMMAND 2

COMMAND 1

DATA 0

(Hexadecimal)

DATA 1

(Hexadecimal)

DATA 2

(Hexadecimal)

DATA 3

(Hexadecimal)

Command Reference List

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Prev.

EZ Scan

Ch.Edit

DTV Signal

Ch. Label

Main Input

Sub Input

Front Display

SET ID

Page 36

36 Plasma TV

External Control Device Setup

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the Monitor.

Transmission

Data 0: DTV

1: Analog 2: Video 1 3: Video 2 4: Component 1

5: Component 2 6: RGB-DTV 7: RGB-PC 8: DVI-DTV 9: DVI-PC

Data 0: Auto (Set by program)

1: Normal screen (4:3) 2: Wide screen (16:9) 3: Horizon 4: Zoom 1

5: Zoom 2 6: Cinema Zoom (1)

15: Cinema Zoom (16)

[k][b][ ][Set ID][ ][Data][Cr]

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

01. Power (Command2:a)

G To control Power On/Off of the Monitor.

Transmission

Data 0 : Power Off 1 : Power On

[k][a][ ][Set ID][ ][Data][Cr]

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback presents status about each function.

Real data mapping

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

64 : Step 100

05. Volume Mute (Command2:e)

G To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

ransmission

Data 0 : Volume mute off (Volume on)

1 : Volume mute on (Volume off)

[k][e][ ][Set ID][ ][Data][Cr]

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust the screen format.

You can also adjust the screen format using the RATIO button on remote control or in the Option menu.

ransmission

[k][c][ ][Set ID][ ][Data][Cr]

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command2:d)

G To select screen mute on/off.

ransmission

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

[k][d][ ][Set ID][ ][Data][Cr]

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G To adjust volume.

You can also adjust volume with the volume buttons on remote control.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][f][ ][Set ID][ ][Data][Cr]

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G To adjust screen contrast.

You can also adjust contrast in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][g][ ][Set ID][ ][Data][Cr]

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h)

G To adjust screen brightness.

You can also adjust brightness in the Video menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][h][ ][Set ID][ ][Data][Cr]

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

Page 37

Owner’s Manual 37

External Control Device Setup

09. Color (Command2:i)

G To adjust the screen color.

You can also adjust color in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’. See page 36.

[k][i][ ][Set ID][ ][Data][Cr]

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G To adjust the screen tint.

You can also adjust tint in the Video menu.

ransmission

Data Red : 0 ~ Green : 64

• Refer to ‘Real data mapping’. See page 36.

[k][j][ ][Set ID][ ][Data][Cr]

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)

G To lock the remote control and the front panel controls on

the set.

Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Lock off 1: Lock on

[m][ ][Set ID][ ][OK][Data][x]

14. PIP / POP / Twin Picture (Command2:n)

G To control the PIP (Picture-in-Picture)/POP/Twin picture.

You can also control the PIP/POP/Twin picture using the PIP button on the remote control.

Transmission

Data 0: PIP off

1: PIP

2: POP 3: Twin Picture

[k][n][ ][Set ID][ ][Data][Cr]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

G To adjust the screen sharpness.

You can also adjust sharpness in the Video menu.

Transmission

11. Sharpness (Command2:k)

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 36.

[k][k][ ][Set ID][ ][Data][Cr]

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G To select OSD (On Screen Display) on/off.

Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: OSD off 1: OSD on

[l][ ][Set ID][ ][OK][Data][x]

15. PIP Position (Command2:q)

G To select sub picture position for PIP.

Transmission

[k][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Right down on screen

1: Right up on screen 2: Left up on screen 3: Left down on screen

[q][ ][Set ID][ ][OK][Data][x]

16. Treble (Command2:r)

G To adjust treble.

You can also adjust treble in the Audio menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 36.

[k][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

18. Balance (Command2:t)

G To adjust balance.

You can also adjust balance in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 36.

[k][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

17. Bass (Command2:s)

G To adjust bass.

You can also adjust bass in the Audio menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 36.

[k][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

Page 38

38 Plasma TV

External Control Device Setup

19. Color Temperature (Command2:u)

G To adjust color temperature.

You can also adjust color temperature in the Video menu.

ransmission

Data 0: Warm 1: Medium 2: Cool

[k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

23. Orbiter Time Setting (Command2:r)

G To adjust orbiter operation time term.

Transmission

Data Min: 1 ~ Max: 64

[j][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

24. Orbiter Pixel Setting (Command2:s)

G To adjust pixel number in orbiter function.

Transmission

Data Min: 0 ~ Max: A

[j][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

25. Channel Tuning (Command: m a)

G To tune channel to following physical/major/minor number

ransmission

Data 0:

Physical channel number (Transmit by Hexadecimal code)

* NTSC air: 02 ~ 45

NTSC cable: 01, 0E ~ 7D ATSC air: 01 ~ 45 ATSC cable: 01 ~ 87

Major channel number (Transmit by Hexadecimal code)

* NTSC air: 02 ~ 45, NTSC cable: 01 ~ 7D

ATSC air: 01 ~ 63, ATSC cable: 01 ~ 87

Minor channel number (Transmit by Hexadecimal code)

* NTSC air: 00 (must be 0), ATSC: 01 ~ FE

3: High nibble → Main picture: 0, Sub picture (PIP): 1

Low nibble → NTSC air: 0, NTSC cable: 1, ATSC: 2, Example) If you want PIP channel tuned to ATSC cable (standard) 30-5, the command sequence is ma 00 1e 1e 05 12.

* To change the channel between ATSC air and ATSC cable,

change the antenna setting with EZ Scan.

[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][Cr]

[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][x] [a][ ][Set ID][ ][NG][Data0][x]

Acknowledgement

26. Channel Add/Del (Command: m b)

G To add and delete the channels

Transmission

Data 0: Channel Delete

1: Channe Add

[m][b][ ][Set ID][ ][Data][Cr]

[b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x]

Acknowledgement

27. Key (Command: m c)

G To send IR remote key code

ransmission

Data Key code: Refer to page 40.

* It’s impossible to command the IR Code 0x08 and 0xC4

with RS-232C.

[m][c][ ][Set ID][ ][Data][ ][Cr]

[c][ ][Set ID][ ][OK][Data][x]

Acknowledgement

20. PIP Input Select (Command2:y)

G To select input source for sub picture in PIP/Twin pic-

ture mode.

ransmission

Data 0: DTV

1: Analog 2: Video 1 3: Video 2

[k][y][ ][Set ID][ ][Data][Cr]

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

21. ISM Method (Command2:p)

G To avoid having a fixed image remain on screen.

Transmission

Data 0: Normal

1: Orbiter 2: Inversion

[j][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

22. White Wash (Command2:q)

G To control the white wash function on/off.

You can also adjust white wash in Option menu.

ransmission

Data 0: White Wash off

1: White Wash on

[j][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

Page 39

Owner’s Manual 39

IR Codes

G Connect your wired remote control to the Remote Control port on the TV.

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

G Configuration of frame

G Repeat code

G Lead code

• 1st frame

Low custom code

Lead code

High custom code

Data code

Carrier frequency

CAR = 1/TC = fOSC/12

Duty ratio = T1/TC = 1/3

• Repeat frame

C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G Bit description

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

• Bit “0”

Tf Tf

Tf=108ms @455KHz

0.56 ms 0.56 ms

1.12 ms

• Bit “1”

2.24 ms

How to Connect

Remote Control IR Codes

IR Codes

Page 40

40 Plasma TV

IR Codes

0x0B

0x08 0xC4 0xC5 0x98 0x79 0x0E 0x10 ~ 0x19 0x4C 0x1A 0x09 0x02 0x03 0x00 0x01 0x1E 0xAA 0x39 0x40 0x41 0x07 0x06 0x44 0x43 0x52 0x4D 0x5B 0x60 0x72 0x71 0x61 0x63 0x65 0x7B 0x0A 0xCB 0xD6 0x5A 0xD0 0xBF 0xD4 0xD5 0xD7 0xC6 0x76 0x77 0xAF 0x70 0x96

R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video1 Input Selection) Discrete IR Code (Video2 Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (DVI-DTV Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom Mode) Channel Search R/C Button

Code (Hexa) Function Note

TV/VIDEO MODE POWER POWER ON POWER OFF COMP/RGB/DVI RATIO TIMER Number Key 0~ 9

- (Dash) FLASHBK MUTE VOL + VOL CH + CH SURF INFO CC

D E F G

OK MENU SOUND VIDEO EXIT PIP PIPCH PIPCH + PIP INPUT SWAP FREEZE ZOOM SAP ADJUST TV VIDEO 1 VIDEO 2 COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV DVI-DTV Ratio 4:3 Ratio 16:9 Ratio Zoom MULTI PIP SIGNAL

Page 41

Owner’s Manual 41

Programming the Remote

G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable

devices of other manufacturers. Note that the remote control may not control all models of other brands.

Programming a code into a remote mode

Programming the Remote

1. Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding MODE button (VCR) on the remote control, while pointing at the component. Test the POWER and CH +/- buttons to see if the component responds properly. If not, the remote requires programming to operate the device.

2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control.

3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.

4. There are two ways to find the right code for the component. A. If you press the CH +/- buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code

change. If the right code is found, the device will turn off.

B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component

can be found on the following pages. Again, if the code is correct, the device will turn off.

5. Press the MENU button to store the code.

6. Test the remote control functions to see if the component responds properly. If not, repeat from step 2.

Page 42

42 Plasma TV

Programming Codes

VCRs

CACATV

AIWA 034 AKAI 016 043 046 124

125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS

012 023 039 043 BROKSONIC 035 037 129 CANON 028 031 033 CAPEHART 108 CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064

065 108 110 111

112 11 6 117 119 DAYTRON 108 DBX 012 023 039 043 DYNATECH 034 053 ELECTROHOME 059 EMERSON 006 017 025 027

029 031 034 035

036 037 046 101

129 131 138 153 FISHER 003 008 009 010 FUNAI 034 GE 031 033 063 072

107 109 144 147 GO VIDEO 132 136 HARMAN KARDON

012 045 HITACHI 004 018 026 034

043 063 137 150 INSTANTREPLAY 031 033 JCL 031 033 JCPENNY 012 013 015 033

040 066 101 JENSEN 043 JVC 012 031 033 043

048 050 055 060

130 150 152

KENWOOD 014 034 039 043

047 048

LG (GOLDSTAR) 001 012 013 020

101 106 114 123 LLOYD 034 LXI 003 009 013 014

017 034 101 106 MAGIN 040 MAGNAVOX 031 033 034 041

067 068 MARANTZ 012 031 033 067

069 MARTA 101 MATSUI 027 030 MEI 031 033 MEMOREX 003 010 014 031

033 034 053 072

101 102 134 139 MGA 045 046 059 MINOLTA 013 020 MITSUBISHI 013 020 045 046

049 051 059 061

151 MTC 034 040 MULTITECH 024 034 NEC 012 023 039 043

048 NORDMENDE 043 OPTONICA 053 054 PANASONIC 066 070 074 083

133 140 145 PENTAX 013 020 031 033

063 PHILCO 031 034 067 PHILIPS 031 033 034 054

067 071 101 PILOT 101 PIONEER 013 021 048

PORTLAND 108 PULSAR 072 QUARTZ 011 014 QUASAR 033 066 075 145 RCA 013 020 033 034

040 041 062 063 107 109 140 144 145 147

REALISTIC 003 008 010 014

031 033 034 040

053 054 101 RICO 058 RUNCO 148 SALORA 014 SAMSUNG 032 040 102 104

105 107 109 112

113 115 120 122

125 SANSUI 022 043 048 135 SANYO 003 007 010 014

102 134 SCOTT 017 037 112 129

131 SEARS 003 00 009 010 013 014 017 020

031 042 073 081

101 SHARP 031 054 149 SHINTOM 024 SONY 003 009 031 052

056 057 058 076

077 078 149 SOUNDESIGN 034 STS 013 SYLVANIA 031 033 034 059

067 SYMPHONIC 034 TANDY 010 034

TATUNG 039 043 TEAC 034 039 043 TECHNICS 031 033 070 TEKNIKA 019 031 033 034

101 THOMAS 034 TMK 006 TOSHIBA 008 013 042 047

059 082 112 131 TOTEVISION 040 101 UNITECH 040

VECTOR RESEARCH

012 VICTOR 048 VIDEO CONCEPTS

012 034 046 VIDEOSONIC 040 WARDS 003 013 017 024

031 033 034 040

053 054 131 YAMAHA 012 034 039 043 ZENITH 034 048 056

058 072 080 101

Brand Codes Brand Codes Brand Codes Brand Codes

ABC 003 004 039 042

046 052 053 AJIN 112 ANTRONIK 014 ARCHER 005 007 014 024 CABLE STAR 026 CENTURION 092 CENTURY 007 CITIZEN 007 COLOUR VOICE 065 090 COMBANO 080 081 COMTRONICS 019 030 DIAMOND 023 EAGLE 020 030 040 EASTERN 057 062 066 ELECTRICORD 032 GE 072 GEMINI 008 022 025 054 GI 052 074

GOLDEN CHANNEL

030 HAMLIN 049 050 055 HITACHI 052 055 HOSPITALITY 070 077 JERROLD 002 003 004 008

009 010 052 069

074 LG (GOLDSTAR) 001 106 101 005 M-NET 037 MACOM 033 MAGNAVOX 010 012 064 079 MEMOREX 100 MOVIE TIME 028 032 NSC 015 028 038 071

073 OAK 016 031 037 053 PANASONIC 044 047 PARAGON 100 PHILIPS 006 012 013 020

065 085 090

PIONEER 034 051 052 063

076

POST NEWS WEEK

016 PRUCER 059 PTS 011 048 071 072

073 074 PULSAR 100 RCA 047 REGAL 049 050 REGENCY 057 REMBRANT 025 RK 091 SAMSUNG 102 107 030 068

SCIENTIFIC ATLANTA

003 011 041 042

043 045 046 SHERITECH 022 SIGNAL 030 SIGNATURE 052

SL MARX 030 SPRUCER 047 078 STARCOM 002 004 008 009 STARGATE 008 030 SYLVANIA 067 TADIRAN 030 TAEKWANG 110 TAIHAN 105 TANDY 017 TEXSCAN 029 067 TOCOM 039 040 056 TOSHIBA 100 UNIKA 007 014 024 UNITED CABLE 004 053 UNIVERSAL 005 007 014 024

026 027 032 035

VIEWSTAR 012 015 018 086

087 088 089

ZENITH 100 114 060 093

Page 43

Owner’s Manual 43

Programming Codes

Audio

APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025

MAGNAVOX 013 MARANTZ 024 MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009

PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006 RCA 005 006 SAMSUNG 011 015

SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025

DVD

ALPHASTAR DSR

123 AMPLICA 050 BIRDVIEW 051 126 129 BSR 053 CAPETRONICS 053 CHANNEL MASTER

013 014 015 018

036 055 CHAPARRAL 008 009 012 077 CITOH 054 CURTIS MATHES 050 145 DRAKE 005 006 007 010

011 052 112 116

141 DX ANTENNA 024 046 056 076 ECHOSTAR 038 040 057 058

093 094 095 096

097 098 099 100

122 ELECTRO HOME 089

EUROPLUS 114 FUJITSU 017 021 022 027

133 134

GENERAL INSTRUMENT

003 004 016 029 031 059 101

HITACHI 139 140

HOUSTON TRACKER

033 037 039 051

057 104 HUGHES 068 HYTEK 053 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 144 MACOM 010 059 063 064

065

MEMOREX 057 NEXTWAVE 028 124 125 NORSAT 069 070

PACE SKY SATELLITE 143

PANASONIC 060 142 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 102 PRIMESTAR 030 110 111 PROSAT 072 RCA 066 106 REALISTIC 043 074 SAMSUNG 123

SATELLITE SERVICE CO

028 035 047 057 085

SCIENTIFIC ATLANTA

032 138

SONY 103

STARCAST 041 SUPER GUIDE 020 124 125 TEECOM 023 026 075 087

088 090 107 130

137 TOSHIBA 002 127 UNIDEN 016 025 042 043

044 045 048 049

078 079 080 086

101 UNIDEN 135 136 VIEWSTAR 115 WINEGARD 128 146 ZENITH 081 082 083 084

091 120

HDSTB

Brand Codes Brand Codes Brand Codes Brand Codes

AIWA 014 028 070 096

125 129 139 229

230 AKAI 163 ANAM 003 014 017 023

059 106 189 216

217 235 236 BURMECTER 252 CARVER 086 CLARION 199 DAEWOO 027 053 060 084

102 148 198 221 DENON 015 075 130 143 FANTASIA 071 FINEARTS 022 FISHER 089 099 LG(GOLDSTAR) 001 021 024 029

087 107 108 110

190 191 192 210

211 212 239 HAITAI 034 035 188 222 HARMAN/KARDON 068 INKEL 037 058 062 069

078 079 095 121

122 149 150 151

152 153 154 155

157 158 159 160

189 207 222 224

225 226 227 243

247

JVC 004 013 141 KEC 185 186 187 KENWOOD 038 050 067 089

170 171 197 206

215 222 KOHEL 030 NAD 045 046 LOTTE 014 016 036 098

100 172 173 174

175 176 177 178

179 180 181 183

201 202 208 213

214 219 223 232

238 240 LXI 103 MAGNAVOX 111 MARANTZ 002 018 020 025

034 041 081 090

097 112 MCINTOSH 049 MCS 104 MEMOREX 107 NAD 046 ONKYO 013 040 041 047

048 056 057 132

133 140 OPTIMUS 158 PANASONIC 007 033 064 113

142 220 241 251 PENNEY 104

PHILIPS 026 112 143 253 PIONEER 039 042 043 063

065 091 093 094

115 123 127 250 QUASAR 113 RCA 080 RCX 092 REALISTIC 103 106 SAMSUNG 124 145 146 182

193 194 195 203

204 244 245 246 SANSUI 011 135 138 144 SANYO 019 083 234 SCOTT 106 186 SHARP 031 032 051 052

072 082 117 119

156 184 199 200

206 209 SHERWOOD 005 006 158 SONY 044 045 109 114

118 126 248 249 TAEKWANG 012 020 073 074

076 077 105 161

162 163 164 165

166 167 168 169

205 231 233 242

254 TEAC 010 085 106 136

185 187 237 TECHNICS 101 113 128 134

147 218 TOSHIBA 137 THE 061 VICTOR 088 131 WARDS 089 YAMAHA 054 055 066 092

199

Brand Codes Brand Codes Brand Codes Brand Codes

Page 44

44 Plasma TV

Troubleshooting Checklist

No output from one of

the speakers

• Adjust Balance in the AUDIO menu. (Refer to p.22)

Unusual sound from

inside the TV

• A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV.

No picture &

No sound

• Check whether the TV is turned on.

• Is the power cord inserted into wall power outlet?

• Test the wall power outlet, plug another product’s power cord into the outlet where the TV’s power cord was plugged in.

No or poor color

or poor picture

• Select Color in the Video menu and press the VOLUME (G) button. (Refer to p.21)

• Keep a sufficient distance between the TV and the VCR.

• Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

The remote control

doesn’t work

• Check to see if there is any object between the TV and the remote control causing obstruction.

• Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.9)

• Correct remote operating mode set: TV, VCR etc.?

• Install new batteries. (Refer to p.9)

Picture OK &

No sound

• Press the VOLUME (G) button.

• Sound muted? Press MUTE button.

Picture appears slowly

after switching on

• This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes.

Horizontal/vertical bars

or picture shaking

• Check for local interference such as an electrical appliance or power tool.

TTroubleshooting Checklist

roubleshooting Checklist

Page 45

Owner’s Manual 45

Maintenance

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Cleaning the Cabinet

Extended

Absence

Maintenance

Page 46

46 Plasma TV

Product Specification

• The specifications shown above may be changed without prior notice for quality improvement.

Product Specifications

MODELS

AC100-240V ~ 50/60Hz

NTSC-M, ATSC

VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125, CADTV 1 ~ 135. DTV 2 ~ 69

75 Ω

1024 x 768 (Dot) 1366 x 768 (Dot)

16,770,000 (256 steps of each R, G and B)

32 ~ 104°F (0 ~ 40°C)

Less than 80%

6561 feet (2000m)

41 / 1040

27.5 / 699.5

3.7 / 95

76.1 / 34.5

41 / 1040

26.4 / 669.5

3.7 / 95

73.4 / 33.3

48.2 / 1225

30.6 / 778

3.85 / 98

101.2 / 45.9

48.3 / 1226.2

30.6 / 778

3.9 / 99

98.1 / 44.5

Width (inches / mm)

Height (inches / mm)

Depth (inches / mm)

Weight (pounds / kg)

Power requirement

Television System

Program Coverage

External Antenna Impedance

Resolution

Color

Operating Temperature Range

Operating Humidity Range

Maximum Elevation

DU-42PZ60/42PZ60A

/42PZ60B/42PZ60C /42PZ60K/42PZ60R /42PZ60S

DU-42PZ60H/42PZ60HA

/42PZ60HB/42PZ60HC /42PZ60HK/42PZ60HR /42PZ60HS

DU-50PZ60/50PZ60A

/50PZ60B/50PZ60C /50PZ60K/50PZ60R /50PZ60S

DU-50PZ60H/50PZ60HA

/50PZ60HB/50PZ60HC /50PZ60HK/50PZ60HR /50PZ60HS

DU-42PZ70/42PZ70A

/42PZ70B/42PZ70C /42PZ70K/42PZ70R /42PZ70S

DU-42PZ70H/42PZ70HA

/42PZ70HB/42PZ70HC /42PZ70HK/42PZ70HR /42PZ70HS

DU-50PZ70/50PZ70A

/50PZ70B/50PZ70C /50PZ70K/50PZ70R /50PZ70S

DU-50PZ70H/50PZ70HA

/50PZ70HB/50PZ70HC /50PZ70HK/50PZ70HR /50PZ70HS

Page 47

Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, including Alaska, Hawaii, and U.S. Territories.

LG ELECTRONICS, INC.

PLASMA TV — U.S. LIMITED WARRANTY

CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use of your display.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do

not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state.

WARRANTY PERIOD:

LABOR and PARTS: 2 YEARS from the Date of Purchase.

Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGE’s option. If repaired, parts used in the repair may be new or remanufactured. Replacement Units and Repair Parts are warranted for the remaining portion of the original unit’s warranty period.

EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service.

HOW SERVICE IS HANDLED:

In-Home Service: Please retain dealer’s

dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, and submit a copy of the bill of sale to the service person at the time warranty service is provided.

Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center.

Visit our website at:

http://www.lgservice.com

IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your

product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you.

Page 48

TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL:

LGE Customer Interactive Center P.O. Box 240007 201 James Record Road Huntsville, Alabama 35824 http://www.lgservice.com

FOR SERVICE: Before you call for warranty service, check your operating guide – you may avoid a service call.

For warranty service information, please contact the LGE Customer Interactive Center telephone number.

When calling for service, please have your product model number, serial number and the date of pur-

chase or the date of original installation available.

If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days.

If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LG

Brand Service Center.

Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations.

To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details.

CUSTOMER INTERACTIVE CENTER NUMBERS:

To obtain customer assistance, product information or Dealer or Service locations

Call 1-201-816-2000

24 hours a day, 365 days per year

THIS LIMITED WARRANTY DOES NOT APPLY TO:

The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.

● damage caused in shipping or transit

● service required as a result of improper installation,

including incorrect or insufficient AC supply (please consult the owner’s manual for power supply requirements)

● installation or repair of antenna systems, cable con-

verters, cable company supplied equipment, or other components in a video system

● set-up or adjustment on consumer controls, or

damage caused by improper adjustments

● damage caused by other system components

● any panel that has been modified or incorporated

into any other product

● replacement of batteries on the remote control.

● damage (including cosmetic damage), failure, loss

or personal injury due to misuse, abuse, negli-

gence, improper maintenance or storage, or to acts of nature or other causes beyond our control. (Causes beyond our control include but are not limited to lightning strike, power surges, power outages and water damage.)

● image burn-in

● repair or replacement of warranted parts by other

than LGE authorized service centers.

● units purchased or serviced outside of the coverage

area.

● product where the original factory serial numbers

have been removed, defaced or changed in any way.

● product sold and labeled as “as is, where is” or sim-

ilar disclaimer.

P/NO : 3828VA0434A