Please read this manual carefully before operating
your set and retain it for future reference.
39LY540H-CA
42LY540H-CA
47LY540H-CA
55LY540H-CA
www.lg.com
TABLE OF CONTENTS
3 EZ MANAGER
3 EZ-Manager 2.1 - Introduction
3 EZ-Manager Wizard
4 - Automatically for Setup
5 - Automatically for Setup (USB Configuration)
6 - Manually for Setup
8 INSTALLATION MENU
8 Introduction
9 LG Hotel Mode Setup
17 TV Manager
17 - 1. USB
23 - 2. Diagnostics
25 Password Change
26 Set ID Setup
27 Configuration setup
29 Multi Timer
30 Lock Mode
31 External Speaker
33 HCEC Setup
35 Pro:Centric
36 Clock Setup
37 DOWNLOAD EXTRA CONTENTS
2
EZ MANAGER
EZ-Manager 2.1 - Introduction
The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions.
TV will search the pre-defined channel earlier than all channels(DVB-C only).
The frequencies of pre-defined channels are ‘52500, 866000, 794000, 714000, 634000, 554000, 474000,
387000, 307000, 227000, 147000 kHz’.
EZ-Manager Wizard
Image shown may differ from your TV.
y
If you are using Pro:Centric, this setup wizard till help you easily set up the TV.
Select 'Next' to continue.
Otherwise, you may select either 'No Pro:Centric',
if you will not be installing a Pro:Centric Server or 'Exit' to quit.
3
EZ-Manager Wizard - Automatically for Setup
1. Select a Label and/or enter the Room Number using the numeric keypad on the remotes.
To continue, move and select 'Next'.
2.
This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the
"Next".
3. Downloading the Pro:Centric application files takes few minutes.
4. After the installation is completed, the following screen will be displayed.
4
EZ-Manager Wizard - Automatically for Setup (USB Configuration)
1. Select the ‘USB Configuration → Ez Download’.
Ez Download (USB Port1)
[TLL] GlobalClone00001.TLL
[TLL] GlobalClone00002.TLL
[
LOGO
] amazing_nature_full_hd_wallpaper_..
[EPK] M1A_DVB_CN_PROC_RevNo.3649_V02..
[ TV Software Version ]
Current : 02.00.00.01
EPK : 02.00.00.01
[ Forced Update Option ]
SPI Boot
LG Boot Logo
Apply
Previous
OK
* IF you have USB Memory for “lg_dtv” or “LG_DTV” folder, this step automatically searches for the USB file list page.
2. Downloading the software/jpeg/TLL files takes few minutes.
3. After the installation is completed, turn off.
5
EZ-Manager Wizard - Manually for Setup
1. Select a Label and/or enter the Room Number using the numeric keypad on the remotes.
To continue, move and select 'Next'.
2. Please select the 'Manual Pro:Centric’.
3. Select the Pro:Centric Mode "GEM" or "Flash".
6
3. Downloading the Pro:Centric application files takes few minutes.
4. After the installation is completed, the following screen will be displayed.
7
INSTALLATION MENU
Introduction
The abundant functions for Hotel TV linked with software installation can be projected on OSD as
‘Installation Menu’.
The wide range of hotel features can be performed simply on additional window to enhance the LG
hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.
Image shown may differ from your TV.
y
Installation Menu (V 3.0)
LG Hotel Mode Setup
TV Manager
Password Change
PICTURE
SETUP
OPTIONLOCK
INPUT
TIMEAUDIO
My Media
TV
7
C05
Set ID Setup
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Pro:Centric
S/W : 02.00.00.01 Micom : 0.00.84
OK
8
Press the Home button for more than 5 seconds using the user remote control, programme
1
information will appear at top left on the screen.
2
Enter a four digit password and press OK button.
• The TV is set with the initial password “1-1-0-5”.
Use the button to select the desired menu.
3
LG Hotel Mode Setup
Image shown may differ from your TV.
y
Installation Menu (V 3.0)
LG Hotel Mode Setup
TV Manager
Password Change
Set ID Setup
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Pro:Centric
S/W : 02.00.00.01 Micom : 0.00.84
OK
LG Hotel Mode Setup (V 3.0)
Hotel Mode Operation
• Power On Status
• Volume
• Start Volume
• Maximum Volume
• Minimum Volume
• Key Operation
• IR Operation
• Local Key Operation
Previous
▲
▼
◄
Yes
STD
No
Off
100
No
Normal
Normal
►
0
OK
Use the button to select the LG Hotel Mode Setup.
1
Use the OK button and then button to select Hotel Mode Operation.
2
*When 'Hotel Mode Operation' is set to Yes(Work), all functions of Hotel Mode apply.
(1 ) Hotel Mode Operation (DVB)
Decide to work all functions of ‘Hotel Mode Operation’ or not by setting’ Hotel Mode Operation’ as
y
Yes(Work) or No(Do Not Work)
When ‘Hotel Mode Operation’ is set to Yes(Work), all functions of Hotel Mode apply.
y
When ‘Hotel Mode Operation’ is set to No(Do Not Work), all functions of Hotel Mode Do Not apply.
y
When it is set to ‘Yes’, ‘Key Lock’ item of the User menu is disabled and the OSD is displayed same to
y
the Local Key Operation setting of the Hotel mode.
When it is set to ‘Yes’, all items reserved at the Schedule list are deleted and the reservation function is
y
not supported. (applied for the model offering the reservation function)
The TV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately from
y
the Hotel mode.
When it is set to ‘Yes’, User Menu-> Option -> ‘Factory Reset’ is disabled.
y
(2)
Power On Status
Decide to select working status of TV Set when turn on main power.
y
You can set with PWR, STD, LST.
y
PWR always make TV set On status when turn on main power .
y
STD make Stand-by status when turn on main power.
y
LST make TVSet work like previous power status. As same concept as Power Backup mode; If main
y
power were turned off in Power On status, TVSet would work in On status. If main power were turned
off in Stand-by status, TVSet would work in Stand-by status.
9
(3) Volume(0 ≤ Min ≤ Start ≤ Max ≤ 100)
Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’
y
as Yes(Work) or No(Do Not Work).
(3-1) Start Volume
This entry sets the start volume level when is power on.
The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)
y
The default setting is ‘Off’ (disabled).
y
When enabled, if the value is lower then the minimum specified in the minimum volume entry, the
y
minimum volume entry must be used.
When enabled, if the value is larger then the maximum specified in the maximum volume entry, the
y
maximum volume value must be used.
Access to a volume in ‘On Timer’ must be fixed to start volume when ‘Hotel Mode Operation’ (Yes)
y
and ‘Start Volume’ (Off, 0 ~ 100) were set simultaneously.
(3-2) Maximum Volume
This entry sets the maximum volume level the set. The level is specified as a number between
‘Minimum Volume’ to 100. (Min ≤
If the command volume up to higher than maximum volume’ is received, that should be ignored.
y
The default value is 100.
y
(3-3) Minimum Volume
Max
≤ 100)
This entry sets the minimum volume level the set will produce.
The level is specified as a number between 0 to ‘Maximum Volume’. (0 ≤
y
If the command volume down to lower than minimum volume is received, that should be ignored.
y
The default value is 0.
y
Min
≤ Max)
(4) Key Operation
Manage key usability of Local(Front) Key and Remote Control. When selected to ‘Yes’, following ‘IR
y
Operation’ and ‘Local Key Operation’ will be worked by below.
(4-1) IR Operation
Decide whether work the LG remote control or not.
Able to set Normal, Use PWR Only, Block All
y
When ‘IR Operation’ is set to Block All, all normal remote keys don’t work. Use PWR Only (Block
y
except power) makes block all remote keys except power key.
Although ‘IR Operation’ value is Use PWR Only or Block All.
y
»
It can work in ‘Service mode’. (In-Start, In-Stop, Power-Only, ADJ, Hotel-Mode,
Menu key action to enter the ‘Installation Menu’ and key action with
‘Special menu(In-Start / EZ-Adjust …)’ are still available.
When ‘IR Operation’ is set to 0 (Work), all remote keys are available.
y
10
(4-2) Local Key Operation
Decide to operate 'Local/Front Key' working behavior by setting ‘Local Key Operation’ as Normal, Use PWR
Only, Block All.
When 'Local Key Operation' is set to Block All, all local keys don’t work. If value is Use PWR Only, it
y
blocks all local keys except power key.
When 'Local Key Operation' is set to Normal, all local key are available.
y
Exception)
In case of power off condition with all key are blocked, ‘Power On Status’ value turns to ‘PWR’,
and disabled status to fix value for power on operation. (fool-proof routine)
• Power On Status
• Key Management
• IR Operation
• Local Key Operation
◄
◄
◄
Block All
◄
Block All
STD
Yes
►
►
►
►
• Power On Status
• Key Management
• IR Operation
• Local Key Operation
◄
◄
◄
Block All
◄
Block All
PWR
Yes
►
►
►
►
(5) Limited Mode
Configure TV function’s limitation. When selected to ‘Yes’, following sub-menus will be worked by below.
(5-1) Setup Menu
Decide to enter 'Setup’ Menu’ as ‘Yes’(Enter possible) or ‘No’(Enter impossible)
(5-2) Input Source Change
Decide to change input source or not by setting 'Input Source Change' as Yes(Change possible) or
No (Change impossible).
When ‘Input Source Change’ is set to ‘No’ (Change impossible)
y
»
‘INPUT key’ doesn't work, and Input Source Changing via ‘TV D/A’ key, ‘TV/RADIO’ key aren’t
possible (ex. Press TV/RADIO Key in HDMI source to view TV channel)
»
User's input (pressing Programme key, numeral key, List key, Q.View key in all Input source
except TV source) doesn't work.
»
Entering 'Setup Menu' item in the 'Main Menu OSD' except TV mode doesn't accepted.
Because entering 'Setup Menu' item makes present mode as TV mode even though present
mode is not TV. Change to TV mode isn’t allowed.
»
TV set always turns on fixed input source and volume information regardless of already
set information.
»
Entering 'Setup Menu' except TV mode is impossible regardless of ‘Programme Change'
or 'Setup Menu' items’ value.
»
TV can be only turned on with the input source which is irrelevant from the programme
related information set (volume, input) in ‘On Time’ Menu.
»
Auto AV and HDMI-CEC still work regardless of Input Source Change’s value.
»
When 'Input Source Change' is set to Yes(Change possible), changing input source is available.
11
(5-3) Programme Change
Decide to change channel or not by setting ‘Program Change' as ‘Yes’(Change Possible) or ‘No’(Change
Impossible) when present source is TV.
When ‘Programme Change' is set to No (Change Impossible)
y
»
Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu' in
the Main Menu OSD is impossible.
»
‘Programme' item in 'On Time' menu will be fixed.
»
Entering ‘Setup Menu' in the 'Main Menu’ OSD is impossible regardless of ‘Setup Menu' item.
When 'Program Change’ is set to Yes(Change Possible), ‘Program Key’, ‘Numeric Key’, ‘List Key’,
y
‘Q.View’ Key does work and entering ‘Channel Menu' in the Main Menu OSD is possible.
(5-4) Menu Display
Function to decide whether work with menu (including relevant menus too) of control key (Yes – Enter
possible) or not (No – Enter Impossible).
Although select No(Enter impossible), the action that press a Menu button for 5 seconds to enter
y
‘Installation Menu’ is available.
When select Yes(Enter possible), Menu works.
y
(5-5) OSD Display
Decide to display OSD or not by setting ‘OSD Display’ as Yes(Display) or No(Do not Display).
When ‘OSD Display’ is set to ‘No’(Do not Display), all OSD is not displayed except some exception.
y
Although select ‘No’ (Do not Display), the action that press a Menu button for 5 seconds to enter
y
‘Installation Menu’ and entering service menu are available. (In-Start, Power-Only, Adjust,
Installation Menu …)
(5-6) System Provider Mode
‘System Provider Mode’ allows access to the menu system from the front panel or remote control
but access is controlled as follows:
When value is ‘Yes’, Accessible Items on the menu system, others are not permissible.