LG 55LX540S, 49LX541H, 32LX300C INSTALLATION MANUAL

INSTALLATION MANUAL

LED TV*

Please read this manual carefully before operating your set and retain it for future reference.

LX54** LX53** LX34** LX33** LX31**

UX34** LX30**

www.lg.com

TABLE OF CONTENTS

ENGLISH

TABLE OF CONTENTS

3 EZ MANAGER

3 EZ-Manager 2.1 - Introduction 3 EZ-Manager Wizard 4 - Automatically for Setup 6 - Automatically for Setup (USB

Configuration)

7 - Manually for Setup

9 DIGITAL SIGNAGE MEDIA

PLAYER

9 Digital Signage Media Player Overview

10 INSTALLATION MENU

10 Introduction 11 Introduction

18 TV MANAGER

18 1. USB 18 - Ez Download 19 - USB Cloning 20 - Receive From USB 22 - Send To USB 23 - Logo Image Download 24 2. Diagnostics 24 - Diagnostics Setup

26 PASSWORD CHANGE

34 SPEAKER OUTPUT SETUP

35 HCEC SETUP

36 NETWORK SETUP

37 PRO:CENTRIC

39 POWER SAVING

40 SUPERSIGN SERVER SETUP

41 NO SIGNAL IMAGE

42 WELCOME VIDEO

43 NTP TIMER SYNC

44 DOWNLOAD EXTRA CONTENTS

44 Download Extra Contents(flash file) to TV

set

27 SET ID SETUP

28 CONFIGURATION SETUP

31 MULTI TIMER

32 LOCK MODE

33 EXTERNAL SPEAKER

46 IR CODES

47 EXTERNAL CONTROL DEVICE

SETUP

EZ MANAGER

(* Only for LX54*H, LX53*H series)

Image shown may differ from your TV.



EZ-Manager 2.1 - Introduction

(* Only for LX54*H, LX53*H series)

The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions.

The default Domain "procentric.local" and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain "procentric.local" via IP on server search page. If TV doesn't contact the Server, TV will search the pre-defined channel earlier than all channels (DVB-C only)

The frequencies of pre-defined channels are ‘794000, 714000, 634000, 554000, 474000, 394000, 314000, 234000, 154000, 90000 khz’.

EZ-Manager Wizard

Image shown may differ from your TV.



ENGLISH

If you are using Pro:Centric, this setup wizard till help you easily set up the TV. Select 'Next' to continue.

Otherwise, you may select either 'No Pro:Centric', if you will not be installing a Pro:Centric Server or 'Exit' to quit.

EZ MANAGER

ENGLISH

Automatically for Setup

1 Select a Label and/or enter the Room Number using the numeric keypad on the remotes. To

continue, move and select 'Next'.

Image shown may differ from your TV.



2 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data

channel, select the "Next".

EZ MANAGER

3 Downloading the Pro:Centric application les takes few minutes.

4 After the installation is completed, the following screen will be displayed.

ENGLISH

EZ MANAGER

ENGLISH

Automatically for Setup (USB Conguration)

1 Select the ‘USB Conguration → Ez Download’.

Ez Download

[ TV Software Version ] Current : 02.00.00.01 EPK : 02.00.00.01

[ Forced Update Option ] SPI Boot LG Boot Logo

Apply

[TLL] GlobalClone00001.TLL

[LOGO] 1360X768.jpg

[EPK] M1A_DVB_CN_RevNo1901_V02.0...

2 Downloading the software/jpeg/TLL les takes few minutes.

3 After the installation is completed, turn off.

EZ MANAGER

Manually for Setup

1 Select a Label and/or enter the Room Number using the numeric keypad on the remotes.

To continue, move and select 'Next'.

2 Please select the 'Manual Pro:Centric’.

3 Select the Pro:Centric Mode "GEM" or "Flash".

ENGLISH

EZ MANAGER

ENGLISH

(* Only for LX545H series)

If you choose 'Philippines' as the country, ‘DVB-C Bandwidth’ item will be shown. Select the bandwidth of cable tuning.(6Mhz/8Mhz)

4 Downloading the Pro:Centric application les takes few minutes.

5 After the installation is completed, the following screen will be displayed.

DIGITAL SIGNAGE MEDIA PLAYER

Digital Signage Media Player Overview

(* Only for LX540S, LX530S series)

The Digital Signage Media Player can play content produced and distributed by SuperSign Elite-W. Supported content types consist of photographs, videos, external inputs such as TV broadcasts, texts,and music.

1 Executable content

*.cts : These files can be played at any time.



*.sce : These files can be played at any time like *.cts files or they can be played to a specific



schedule.

2 Using the My Media menu to play les

After inserting the USB storage device, access the My Media menu and select an executable



content file under the “All Media” tab or the “Contents List” tab to play the file.

3 Auto-play on USB insertion

Files with executable content in a specific folder are automatically played when Power On is



selected or when a USB drive is inserted after Power On. If a USB storage device is already inserted when Power On is selected, files with executable



content in the “normal” folder are played by default. If the “normal” folder does not exist, files with executable content in the “AutoPlay” folder are played instead. If a USB storage device is inserted some time after Power On has been selected, files with



executable content in the “AutoPlay” folder are played by default. If the “AutoPlay” folder does not exist, files with executable content in the “normal” folder are played instead. Auto-play on USB insertion is only supported by USB port #1.



4 Distributing and playing content via SuperSign Elite-W

If a USB storage device is inserted in USB port #1, the LAN cable is connected and the SuperSign



Server settings are configured, content can be received from the SuperSign Elite-W server. Schedules can be set to play a variety of specific content or media files, including photos and



videos, from SuperSign Elite-W whenever the user wants. Messages created by the user can be sent to the player via SuperSign Elite-W.



For more information, see the SuperSign Elite-W manual.



ENGLISH

INSTALLATION MENU

ENGLISH

INSTALLATION MENU

Introduction

The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’. The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.

Image shown may differ from your TV.



Installation Menu (V 3.0)

LG Hotel Mode Setup

TV Manager

Password Change

PICTURE

SETUP

OPTIONLOCK

INPUT

TIMEAUDIO

MY MEDIA

C05

1 Press the Home button for more than 5 seconds using the user remote control, programme information

will appear at top left on the screen.

2 Enter a four digit password and press OK button.

The TV is set with the initial password “1-1-0-5”.



3 Use the button to select the desired menu.

Set ID Setup

Configuration Setup

Multi Timer

Lock Mode

External Speaker

HCEC Setup

IR Setup

S/W : 02.00.00.01 Micom : 0.00.84

INSTALLATION MENU

Introduction

Image shown may differ from your TV.



Installation Menu (V 3.0)

LG Hotel Mode Setup

TV Manager

Password Change

Set ID Setup

Configuration Setup

Multi Timer

Lock Mode

External Speaker

HCEC Setup

IR Setup

S/W : 02.00.00.01 Micom : 0.00.84

1 Use the button to select the LG Hotel Mode Setup. 2 Use the OK button and then button to select Hotel Mode Operation.

*When ‘Hotel Mode Operation’ is set to Yes(Work), all functions of Hotel Mode apply.

1 Hotel Mode Operation (DVB)

Decide to work all functions of ‘Hotel Mode Operation’ or not by setting’ Hotel Mode Operation’ as



Yes(Work) or No(Do Not Work) When ‘Hotel Mode Operation’ is set to Yes(Work), all functions of Hotel Mode apply.



When ‘Hotel Mode Operation’ is set to No(Do Not Work), all functions of Hotel Mode Do Not apply.



When it is set to ‘Yes’, ‘Key Lock’ item of the User menu is disabled and the OSD is displayed same



to the Local Key Operation setting of the Hotel mode. When it is set to ‘Yes’, all items reserved at the Schedule list are deleted and the reservation



function is not supported. (applied for the model offering the reservation function) The TV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately



from the Hotel mode. When it is set to ‘Yes’, User Menu-> Option -> ‘Factory Reset’ is disabled.



2 Power On Status

Decide to select working status of TV Set when turn on main power.



You can set with PWR, STD, LST.



PWR always make TV set On status when turn on main power .



STD make Stand-by status when turn on main power.



LST make TVSet work like previous power status. As same concept as Power Backup mode; If



main power were turned off in Power On status, TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in Stand-by status.

LG Hotel Mode Setup (V 3.0)

Hotel Mode Operation

▲

• Power On Status

• Volume

• Start Volume

• Maximum Volume

• Minimum Volume

• Key Operation

• IR Operation

• Local Key Operation

▼

◄

Yes

STD

Off

100

Normal

►

ENGLISH

INSTALLATION MENU

ENGLISH

3 Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)

Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’



as Yes(Work) or No(Do Not Work).

- Start Volume This entry sets the start volume level when is power on.

The level is specified as a number between minimum volume to maximum value. (Min ≤ Start



≤ Max)

The default setting is ‘Off’ (disabled).



When enabled, if the value is lower then the minimum specified in the minimum volume entry,



the minimum volume entry must be used. When enabled, if the value is larger then the maximum specified in the maximum volume



entry, the maximum volume value must be used. Access to a volume in ‘On Timer’ must be fixed to start volume when ‘Hotel Mode Operation’



(Yes) and ‘Start Volume’ (Off, 0 ~ 100) were set simultaneously.

- Maximum Volume This entry sets the maximum volume level the set. The level is specified as a number between

‘Minimum Volume’ to 100. (Min ≤ Max ≤ 100)

If the command volume up to higher than maximum volume’ is received, that should be



ignored. The default value is 100.



- Minimum Volume This entry sets the minimum volume level the set will produce.

The level is specified as a number between 0 to ‘Maximum Volume’. (0 ≤ Min ≤ Max)



If the command volume down to lower than minimum volume is received, that should be



ignored. The default value is 0.



4 Key Operation

Manage key usability of Local(Front) Key and Remote Control. When selected to ‘Yes’, following ‘IR



Operation’ and ‘Local Key Operation’ will be worked by below.

- IR Operation Decide whether work the LG remote control or not.

Able to set Normal, Use PWR Only, Block All.



When ‘IR Operation’ is set to Block All, all normal remote keys don’t work. Use PWR Only (Block



except power) makes block all remote keys except power key. Although ‘IR Operation’ value is Use PWR Only or Block All.



»It can work in ‘Service mode’. (In-Start, In-Stop, Power-Only, ADJ, Hotel-Mode, Hotel-Mode-

Ready, P-Check, S-check, In-Time, FMode-Init, FMode-Start, FMode-AV, FMode-F1)

»Menu key action to enter the ‘Installation Menu’ and key action with ‘Special menu(In-Start /

EZ-Adjust …)’ are still available.

When ‘IR Operation’ is set to 0 (Work), all remote keys are available.



INSTALLATION MENU

- Local Key Operation Decide to operate 'Local/Front Key' working behavior by setting ‘Local Key Operation’ as Normal, Use PWR Only, Block All. (LX30*C series use only Normal/Block All)

When 'Local Key Operation' is set to Block All, all local keys don’t work. If value is Use PWR



Only, it blocks all local keys except power key. When 'Local Key Operation' is set to Normal, all local key are available.



Exception) In case of power off condition with all key are blocked, ‘Power On Status’ value turns to ‘PWR’, and disabled status to fix value for power on operation. (fool-proof routine)

• Power On Status

• Key Operation

• IR Operation

• Local Key Operation

◄

STD

Yes

Block All

►

• Power On Status

• Key Operation

• IR Operation

• Local Key Operation

5 Limited Mode

Configure TV function’s limitation. When selected to ‘Yes’, following sub-menus will be worked by below.

- Setup Menu Decide to enter 'Setup’ Menu’ as ‘Yes’(Enter possible) or ‘No’(Enter impossible)

- Input Source Change Decide to change input source or not by setting 'Input Source Change' as Yes(Change possible) or No (Change impossible).

When ‘Input Source Change’ is set to ‘No’ (Change impossible)



»‘INPUT key’ doesn't work, and Input Source Changing via ‘TV D/A’ key, ‘TV/RADIO’ key

aren’t possible (ex. Press TV/RADIO Key in HDMI source to view TV channel)

»User's input (pressing Programme key, numeral key, List key, Q.View key in all Input source

except TV source) doesn't work.

»Entering 'Setup Menu' item in the 'Main Menu OSD' except TV mode doesn't accepted.

Because entering 'Setup Menu' item makes present mode as TV mode even though present mode is not TV. Change to TV mode isn’t allowed.

»TV set always turns on fixed input source and volume information regardless of already set

information.

»Entering 'Setup Menu' except TV mode is impossible regardless of ‘Programme Change' or

'Setup Menu' items’ value.

»TV can be only turned on with the input source which is irrelevant from the programme

related information set (volume, input) in ‘On Time’ Menu. »Auto AV and HDMI-CEC still work regardless of Input Source Change’s value. »When 'Input Source Change' is set to Yes(Change possible), changing input source is

available.

◄

Block All

◄

Block All

PWR

Yes

ENGLISH

►

INSTALLATION MENU

ENGLISH

- Programme Change

Decide to change channel or not by setting ‘Program Change' as ‘Yes’(Change Possible) or

‘No’(Change Impossible) when present source is TV.

When ‘Programme Change' is set to No (Change Impossible)



»Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu'

in the Main Menu OSD is impossible. »‘Programme' item in 'On Time' menu will be fixed. »Entering ‘Setup Menu' in the 'Main Menu’ OSD is impossible regardless of ‘Setup Menu'

item. When 'Program Change’ is set to Yes(Change Possible), ‘Program Key’, ‘Numeric Key’, ‘List



Key’, ‘Q.View’ Key does work and entering ‘Channel Menu' in the Main Menu OSD is possible.

- Menu Display Function to decide whether work with menu (including relevant menus too) of control key (Yes –

Enter possible) or not (No – Enter Impossible).

Although select No(Enter impossible), the action that press a Menu button for 5 seconds to



enter ‘Installation Menu’ is available. When select Yes(Enter possible), Menu works.



- OSD Display Decide to display OSD or not by setting ‘OSD Display’ as Yes(Display) or No(Do not Display).

When ‘OSD Display’ is set to ‘No’(Do not Display), all OSD is not displayed except some



exception. Although select ‘No’ (Do not Display), the action that press a Menu button for 5 seconds



to enter ‘Installation Menu’ and entering service menu are available. (In-Start, Power-Only, Adjust, Installation Menu …)

- System Provider Mode

- ‘System Provider Mode’ allows access to the menu system from the front panel or remote control but access is controlled as follows:

When value is ‘Yes’, Accessible Items on the menu system, others are not permissible.



»Input select screens »Sleep timer »Aspect Ratio »Closed Caption »‘Lock’ / ‘My Media’ / ‘Network’ / ‘Support’ / ‘Bluetooth’ Menu ‘Q.menu’, which is related to ‘Setup’ Menu, is not accessible.



If the channel map is empty, ‘Auto-tuning’ guide dialog should be blocked by pressing ‘List’,



‘Fav’, ‘CH+’, ‘CH-’ keys.

6 Power Management

The Power Management feature will turn off the television receiver if no input control command is received from either the Local or IR Key within a selected hours.

Activity on either of these inputs shall restart the ‘Power Management’ timer and check key



time interval again. This entry can be set to a value which is corresponding to the desired hours (1 to 7).



Default value is ‘Off(disabled)’.



TV should off and on after apply this setting.



7 DTV Programme Update

- It is a mode to set whether to update DTV channel information automatically or not.

When DTV Channel Update is set to ’Auto’, the function to update TV’s programme map



according to DTV channel’s stream information DTV Channel Update is set to ‘Manual’, the function to keep TV’s channel map even though



DTV programme’s information is changed.

INSTALLATION MENU

8 Power On Default

Set the input source or channel to display and. A/V settings when turn on power in AC Power On or Stand-by status.

- Input Source Set whether it is turned on by the set input source or by the last stored input source.

It is turned on by the Last Memory Input if the Input source is turned off.



It is turned on by the Last Pr. If the Input source is turned off and the last memory Input is the



RF. The available Input Source values should be rotated.



If both the Input source and the ‘On Time’ menu are set, the Input source takes the priority.



When the Input source is changed to the TV, Programme menu is available.



When the Input source is changed to the ATV, the Program No. is set to 0. (If the channel map



structure does not support this, it depends on model’s channel handling. Access to an input source item and a channel in ‘On Timer’ menu must be disabled when



Power On Default is activated.

- Programme Select start channel number if Input source’s value is TV. (in case of ATV, it means physical channel number.)

- A/V Setting If ‘A/V Setting’ is changed from ‘No’ to ‘Yes’, parameters that are set before entering ‘Installation Menu’ are applied whenever turn on power.

Following Parameters are applied to basic.



»Picture section - PSM mode, Picture Data (Contrast, Brightness, Color, Sharpness, Tint) »Sound section - SSM mode, Sound Data (Balance, Equalizer Data) »AVL (Auto Volume Level) and Language, Teletext language, ARC Data. Except these, other

parameters are applied differently according to the TV-Set.

- Aspect Ratio The aspect ratio determines the default aspect ratio that the set returns to on power up.

The modes are as follows:



»Aspect ratio = “Disabled(0)” stays at previous state, same as consumer model. »Aspect ratio = “Original(1)” »Aspect ratio = “4:3 ratio (2)” »Aspect ratio = “16:9 ratio (3)” If enabled, upon power up the television reset the aspect ratio to the specified state regardless



of how the user has previously changed the aspect ratio. (If "original" is not supported, the television set the aspect ratio to "16:9".)

9 Aux Source Setting

The Auxiliary (Input) Source Setting feature will enable or disable for each external input. When ‘Aux Source Setting’ is set to Yes(Work), the RJP or HDMI-CEC / HTNG will not operate.

- Input Source

Available Input Source List



- Setting

Decide whether selected ‘Input Source’ is usable (Enable) or not (Disable).



User cannot disable the current input’s ‘Aux Source Setting’.



10 Radio Name Display

Instead of ‘Audio Only’, the name of a radio channel is displayed on the screen when a radio broadcast is playing.

Set to Yes(Work) or No(Do Not Work).



If the setting is ‘Yes’, the name of a radio channel is displayed for the radio channel.



ENGLISH

INSTALLATION MENU

ENGLISH

11 Radio Video Blank

Manage video blank channel(sound only). This feature affects on analog channel (ATV) only.

- Start PR. No. Start channel number to video blank.



Available programme to set are 0~199(For Taiwan : TV 2~69, CATV 1~199).



- No. Of. PR. Number of channels to blank



The max value for the ‘No. of PR’ is 10.



Can not set more than maximum available channel number. For example if Start PR. set to



195, “Number of PR”. can not set more than 5. Radio programme should be in sequence with starting programme number.



12 Factory Reset

Factory reset returns all the parameters to the default settings.

• Factory Reset

Press ‘Enter key’ to proceed factory reset. and confirmation message window will be shown.



All user settings and channel settings will be reset. Still Continue?

Yes

When select ‘Yes’, all television settings except UTT value should write to the default settings.



Confirm

INSTALLATION MENU

Public Display Settings / LG Hotel Mode Setup (Value Range Table)

Item Enable Disable Initail

Hotel Mode Operation Yes No No

Power On Status - - *STD

Volume Yes No No

Start Volume Off, Minimum Volume ~ Maximum Volume Off

Maximum Volume Minimum Volume ~ 100 100

Minimum Volume 0 ~ Maximum Volume 0

Key Operation Yes No No

LG IR Operation Normal / Use PWR Only / Block All Normal

Local Key Operation

Limited Mode Yes No No

Setup Menu

Input Source Change

Programme Change

Menu Display Yes No Yes

OSD Display

System Provider Mode

Power Management Off, 1 ~ 7 Off

DTV Channel Update Auto Manual Auto

Power On Default Yes No No

Input Source

Programme

A/V Setting

Aspect Ratio

Normal / Use PWR Only / Block All Normal

Yes No Yes

Yes No No

Off, ATV, DTV, ... Off

Minimum Program ~ Maximum Program Minimum Program

Yes No No

Disable / Original / 4:3 / 16:9 Disable

ENGLISH

LG Hotel Mode Setup (Value Range Table)

Item Enable Disable Initail

Aux Source Setting

Input Source

Settng

Radio Name Display

Radio Video Blank

Start PR. No.

No. Of. PR. 0 ~ 10

(Start PR. NO + No. of PR. <= Max Start PR. NO. + 1)

Factory Reset

Yes No No

Aux Input(AV1 ~ MAX_INPUT) AV1

Enable Disable Enable

Yes No No

0 ~ 199 (Taiwan TV 2 ~ 69 / CATV 1 ~ 199) 1

Confirmation window (Yes / No)

+ 38 hidden pages