LG 55LX341C-CA Installation Manual

INSTALLATION MANUAL
LED TV
Please read this manual carefully before operating your set and retain it for future reference.
LX341C-CA LX341H-CA LX300C-CA
UX340C-CA LX530S-CA
LX540S-CA
LX540S-DA LX530S-DA LX330C-DA
www.lg.com
TABLE OF CONTENTS
3 INSTALLATION MENU
3 Introduction 4 LG Hotel Mode Setup 12 TV Manager 12 - 1. USB 18 - 2. Diagnostics 20 Password Change 21 Set ID Setup 22 Configuration Setup 24 Multi Timer 25 Lock Mode 26 External Speaker 28 HCEC Setup 30 Welcome Video 31 Pro:Centric 32 SuperSign Server Setup 33 No Signal Image 34 NTP Time sync 35 Download Extra Contents 35 - 1. Download Extra Contents(flash file) to
TV set
38 DIGITAL SIGNAGE MEDIA PLAYER
38 Digital Signage Media Player Overview
39 EXTERNAL CONTROL DEVICE
SETUP
39 KEY CODES 40 EXTERNAL CONTROL DEVICE SETUP
2
INSTALLATION MENU
Introduction
The abundant functions for Hotel TV linked with software installation can be projected on OSD as
‘Installation Menu’.
The wide range of hotel features can be performed simply on additional window to enhance the LG
hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.
Image shown may differ from your TV.
Installation Menu (V 3.0)
LG Hotel Mode Setup
LG Hotel Mode Setup
TV Manager
Password Change
Set ID Setup
PICTURE
SETUP
OPTIONLOCK
INPUT
TIMEAUDIO
My Media
TV
7
C05
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Welcome Video
S/W : 02.00.00.01 Micom : 0.00.84
OK
Press the Home button for more than 5 seconds using the user remote control, programme
1
information will appear at top left on the screen.
2
Enter a four digit password and press OK button.
• The TV is set with the initial password “1-1-0-5”.
3
Use the
button to select the desired menu.
3
LG Hotel Mode Setup
Image shown may differ from your TV.
Installation Menu (V 3.0)
LG Hotel Mode Setup
TV Manager
Password Change
Set ID Setup
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Welcome Video
S/W : 02.00.00.01 Micom : 0.00.84
Use the button to select the LG Hotel Mode Setup.
1
Use the OK button and then button to select Hotel Mode Operation.
2
OK
LG Hotel Mode Setup (V 3.0)
Hotel Mode Operation
Power On Status
Volume
Start Volume
Maximum Volume
Minimum Volume
Key Operation
IR Operation
Local Key Operation
Previous
Yes
STD
No
Off
100
No
Normal
Normal
0
OK
*When 'Hotel Mode Operation' is set to Yes(Work), all functions of Hotel Mode apply.
(1 ) Hotel Mode Operation (DVB)
Decide to work all functions of ‘Hotel Mode Operation’ or not by setting’ Hotel Mode Operation’ as
Yes(Work) or No(Do Not Work) When ‘Hotel Mode Operation’ is set to Yes(Work), all functions of Hotel Mode apply.
When ‘Hotel Mode Operation’ is set to No(Do Not Work), all functions of Hotel Mode Do Not apply.
When it is set to ‘Yes’, ‘Key Lock’ item of the User menu is disabled and the OSD is displayed same to
the Local Key Operation setting of the Hotel mode. When it is set to ‘Yes’, all items reserved at the Schedule list are deleted and the reservation function is
not supported. (applied for the model offering the reservation function) The TV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately from
the Hotel mode. When it is set to ‘Yes’, User Menu-> Option -> ‘Factory Reset’ is disabled.
4
(2)
Power On Status
Decide to select working status of TV Set when turn on main power.
You can set with PWR, STD, LST.
PWR always make TV set On status when turn on main power .
STD make Stand-by status when turn on main power.
LST make TVSet work like previous power status. As same concept as Power Backup mode; If main
power were turned off in Power On status, TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in Stand-by status.
(3) Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)
Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’
as Yes(Work) or No(Do Not Work).
(3-1) Start Volume
This entry sets the start volume level when is power on.
The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)
The default setting is ‘Off’ (disabled).
When enabled, if the value is lower then the minimum specified in the minimum volume entry, the
minimum volume entry must be used. When enabled, if the value is larger then the maximum specified in the maximum volume entry, the
maximum volume value must be used. Access to a volume in ‘On Timer’ must be fixed to start volume when ‘Hotel Mode Operation’ (Yes)
and ‘Start Volume’ (Off, 0 ~ 100) were set simultaneously.
(3-2) Maximum Volume
This entry sets the maximum volume level the set. The level is specified as a number between
‘Minimum Volume’ to 100. (Min ≤ Max ≤ 100)
If the command volume up to higher than maximum volume’ is received, that should be ignored.
The default value is 100.
(3-3) Minimum Volume
This entry sets the minimum volume level the set will produce.
The level is specified as a number between 0 to ‘Maximum Volume’. (0 ≤ Min ≤ Max)
If the command volume down to lower than minimum volume is received, that should be ignored.
The default value is 0.
(4) Key Operation
Manage key usability of Local(Front) Key and Remote Control. When selected to ‘Yes’, following ‘IR
Operation’ and ‘Local Key Operation’ will be worked by below.
(4-1) IR Operation
Decide whether work the LG remote control or not.
Able to set Normal, Use PWR Only, Block All
When ‘IR Operation’ is set to Block All, all normal remote keys don’t work. Use PWR Only (Block
except power) makes block all remote keys except power key. Although ‘IR Operation’ value is Use PWR Only or Block All.
»
It can work in ‘Service mode’. (In-Start, In-Stop, Power-Only, ADJ, Hotel-Mode,
Hotel-Mode-Ready, P-Check, S-check, In-Time, FMode-Init, FMode-Start, FMode-AV, FMode-F1)
»
Menu key action to enter the ‘Installation Menu’ and key action with
‘Special menu(In-Start / EZ-Adjust …)’ are still available. When ‘IR Operation’ is set to 0 (Work), all remote keys are available.
5
(4-2) Local Key Operation
Decide to operate 'Local/Front Key' working behavior by setting ‘Local Key Operation’ as Normal, Use PWR Only, Block All.
When 'Local Key Operation' is set to Block All, all local keys don’t work. If value is Use PWR Only, it
blocks all local keys except power key. When 'Local Key Operation' is set to Normal, all local key are available.
Exception)
In case of power off condition with all key are blocked, ‘Power On Status’ value turns to ‘PWR’, and disabled status to fix value for power on operation. (fool-proof routine)
Power On Status
Key Management
IR Operation
Local Key Operation
Block All
Block All
STD
Yes
Power On Status
Key Management
IR Operation
Local Key Operation
Block All
Block All
PWR
Yes
(5) Limited Mode
Configure TV function’s limitation. When selected to ‘Yes’, following sub-menus will be worked by below.
(5-1) Setup Menu
Decide to enter 'Setup’ Menu’ as ‘Yes’(Enter possible) or ‘No’(Enter impossible)
(5-2) Input Source Change
Decide to change input source or not by setting 'Input Source Change' as Yes(Change possible) or No (Change impossible).
When ‘Input Source Change’ is set to ‘No’ (Change impossible)
»
‘INPUT key’ doesn't work, and Input Source Changing via ‘TV D/A’ key, ‘TV/RADIO’ key aren’t
possible (ex. Press TV/RADIO Key in HDMI source to view TV channel)
»
User's input (pressing Programme key, numeral key, List key, Q.View key in all Input source
except TV source) doesn't work.
»
Entering 'Setup Menu' item in the 'Main Menu OSD' except TV mode doesn't accepted.
Because entering 'Setup Menu' item makes present mode as TV mode even though present mode is not TV. Change to TV mode isn’t allowed.
»
TV set always turns on fixed input source and volume information regardless of already
set information.
»
Entering 'Setup Menu' except TV mode is impossible regardless of ‘Programme Change'
or 'Setup Menu' items’ value.
»
TV can be only turned on with the input source which is irrelevant from the programme
related information set (volume, input) in ‘On Time’ Menu.
»
Auto AV and HDMI-CEC still work regardless of Input Source Change’s value.
»
When 'Input Source Change' is set to Yes(Change possible), changing input source is available.
6
(5-3) Programme Change
Decide to change channel or not by setting ‘Program Change' as ‘Yes’(Change Possible) or ‘No’(Change Impossible) when present source is TV.
When ‘Programme Change' is set to No (Change Impossible)
»
Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu' in
the Main Menu OSD is impossible.
»
‘Programme' item in 'On Time' menu will be fixed.
»
Entering ‘Setup Menu' in the 'Main Menu’ OSD is impossible regardless of ‘Setup Menu' item.
When 'Program Change’ is set to Yes(Change Possible), ‘Program Key’, ‘Numeric Key’, ‘List Key’,
‘Q.View’ Key does work and entering ‘Channel Menu' in the Main Menu OSD is possible.
(5-4) Menu Display
Function to decide whether work with menu (including relevant menus too) of control key (Yes – Enter possible) or not (No – Enter Impossible).
Although select No(Enter impossible), the action that press a Menu button for 5 seconds to enter
‘Installation Menu’ is available. When select Yes(Enter possible), Menu works.
(5-5) OSD Display
Decide to display OSD or not by setting ‘OSD Display’ as Yes(Display) or No(Do not Display).
When ‘OSD Display’ is set to ‘No’(Do not Display), all OSD is not displayed except some exception.
Although select ‘No’ (Do not Display), the action that press a Menu button for 5 seconds to enter
‘Installation Menu’ and entering service menu are available. (In-Start, Power-Only, Adjust, Installation Menu …)
(5-6) System Provider Mode
‘System Provider Mode’ allows access to the menu system from the front panel or remote control but access is controlled as follows:
When value is ‘Yes’, Accessible Items on the menu system, others are not permissible.
»
Input select screens
»
Sleep timer
»
Aspect Ratio
»
Closed Caption
»
‘Lock’ / ‘My Media’ / ‘Network’ / ‘Support’ / ‘Bluetooth’ Menu
‘Q.menu’, which is related to ‘Setup’ Menu, is not accessible.
If the channel map is empty, ‘Auto-tuning’ guide dialog should be blocked by pressing ‘List’, ‘Fav’,
‘CH+’ (Page up), ‘CH-’ (Page down) keys.
7
(6) Power Management
The Power Management feature will turn off the television receiver if no input control command is received from either the Local or IR Key within a selected hours.
Activity on either of these inputs shall restart the ‘Power Management’ timer and check key time interval
again. This entry can be set to a value which is corresponding to the desired hours (1 to 7).
Default value is ‘Off(disabled)’.
TV should off and on after apply this setting.
(7) DTV Channel Update
It is a mode to set whether to update DTV channel information automatically or not.
When DTV Channel Update is set to ’Auto’, the function to update TV’s programme map according to
DTV channel’s stream information DTV Channel Update is set to ‘Manual’, the function to keep TV’s channel map even though DTV
programme’s information is changed.
(8) Power On Default
Set the input source or channel to display and. A/V settings when turn on power in AC Power On or Stand­by status.
(8-1) Input Source
Set whether it is turned on by the set input source or by the last stored input source.
It is turned on by the Last Memory Input if the Input source is turned off.
It is turned on by the Last Pr. If the Input source is turned off and the last memory Input is the RF.
The available Input Source values should be rotated.
If both the Input source and the ‘On Time’ menu are set, the Input source takes the priority.
When the Input source is changed to the TV, Programme menu is available.
When the Input source is changed to the ATV, the Program No. is set to 0. (If the channel map structure
does not support this, it depends on model’s channel handling. Access to an input source item and a channel in ‘On Timer’ menu must be disabled when Power On
Default is activated.
(8-2) Programme
Select start channel number if Input source’s value is TV. (in case of ATV, it means physical channel number.)
8
(8-3) A/V Setting
If ‘A/V Setting’ is changed from ‘No’ to ‘Yes’, parameters that are set before entering ‘Installation Menu’ are applied whenever turn on power.
Following Parameters are applied to basic.
»
Picture section - PSM mode, Picture Data (Contrast, Brightness, Color, Sharpness, Tint)
»
Sound section - SSM mode, Sound Data (Balance, Equalizer Data)
»
AVL (Auto Volume Level) and Language, Teletext language, ARC Data.
Except these, other parameters are applied differently according to the TV-Set.
(8-4) Aspect Ratio
The aspect ratio determines the default aspect ratio that the set returns to on power up.
The modes are as follows:
»
Aspect ratio = “Disabled(0)” stays at previous state, same as consumer model.
»
Aspect ratio = “Set by Program(1)”
»
Aspect ratio = “4:3 ratio (2)”
»
Aspect ratio = “16:9 ratio (3)”
If enabled, upon power up the television resets the aspect ratio to the specified state regardless of
how the user has previously changed the aspect ratio. (If "original" is not supported, the television sets the aspect ratio to "16:9".)
(9) Aux Source Setting
The Auxiliary (Input) Source Setting feature will enable or disable for each external input. When ‘Aux Source Setting’ is set to Yes(Work), the RJP or HDMI-CEC / HTNG will not operate.
(9-1) Input Source
Available Input Source List
(9-2) Setting
Decide whether selected ‘Input Source’ is usable (Enable) or not (Disable).
User cannot disable the current input’s ‘Aux Source Setting’.
(10) Radio Name Display
Instead of ‘Audio Only’, the name of a radio channel is displayed on the screen when a radio broadcast is playing.
Set to Yes(Work) or No(Do Not Work).
If the setting is ‘Yes’, the name of a radio channel is displayed for the radio channel.
If the setting is ‘No’, the text ‘Audio Only’ is displayed for the radio channel.
9
(11) Radio Video Blank
(*Except for LX330C-DA series)
Manage video blank channel(sound only). This feature affects on analog channel (ATV) only.
(11-1) Start PR. No.
Start channel number to video blank.
Available programme to set are 0~199(For Taiwan : TV 2~69, CATV 1~199).
(11-2) No. Of. PR.
Number of channels to blank
The max value for the ‘No. of PR’ is 10.
Can not set more than maximum available channel number. For example if Start PR. set to 195,
“Number of PR”. can not set more than 5. Radio programme should be in sequence with starting programme number.
(12) Factory Reset
Factory reset returns all the parameters to the default settings.
Factory Reset
Press ‘Enter key’ to proceed factory reset. and confirmation message window will be shown.
All user settings and channel settings will be reset. Still Continue?
Yes
When select ‘Yes’, all television settings except UTT value should write to the default settings.
Confirm
No
10
Public Display Settings / LG Hotel Mode Setup (Value Range Table)
Item Enable Disable Initial
Hotel Mode Operation Yes No No
Power On Status - - *STD
Volume Yes No No
Start Volume Off, Minimum Volume ~ Maximum Volume Off
Maximum Volume Minimum Volume ~ 100 100
Minimum Volume 0 ~ Maximum Volume 0
Key Management Yes No No
LG IR Operation Normal / Use PWR Only / Block All Normal
Local Key Operation Normal / Use PWR Only / Block All Normal
Limited Mode Yes No No
Setup Menu Yes No Yes
Input Source Change Yes No Yes
Programme Change Yes No Yes
Menu Display Ye s No Yes
OSD Display Yes No Yes
System Provider Mode Yes No No
Power Management Off, 1 ~ 7 Off
DTV Channel Update Auto Manual Auto
Power On Default Yes No No
Input Source Off, ATV, DTV, ... Off
Programme Minimum Program ~ Maximum Program Minimum Program
A/V Setting Ye s No No
Aspect Ratio Disable / Original / 4:3 / 16:9 Disable
LG Hotel Mode Setup (Value Range Table)
Item Enable Disable Initial
Aux Source Setting Ye s No No
Input Source Aux Input(AV1 ~ MAX_INPUT) AV1
Settng Enable Disable Enable
Radio Name Display Yes No No
Radio Video Blank Yes No No
Start PR. No. 0 ~ 199 (Taiwan TV 2 ~ 69 / CATV 1 ~ 199) 1
No. Of. PR. 0 ~ 10
(Start PR. NO + No. of PR. <= Max Start PR. NO. + 1)
Factory Reset Confirmation window (Yes / No)
1
11
TV Manager
1. USB
Ez Download
Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL (see Send to USB descriptions for more information regarding file types), Logo Image, etc (TLX, MICOM for Pro:Centric). * Splash images and EPK files should be copied into the folder named LG_DTV on the USB. TLL files should be copied to the root folder of the USB.NoSignal Image files shoud be copied into the folder named LG_SIG on the USB.
Image shown may differ from your TV.
1
Plug USB memory card into the USB port of the TV.
2
Use the button to select the TV Manager option and then press the OK button.
Installation Menu (V 3.0)
LG Hotel Mode Setup
TV Manager
Password Change
Set ID Setup
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Welcome Video
S/W : 02.00.00.01 Micom : 0.00.84
OK
12
Use the button to select the USB and Ez Download and press the OK button.
3
TV Manager
USB
Diagnostics
Previous
Select a list to download and press the OK button.
4
Ez Download
Receive from USB
Send to USB
Logo Image Download
OK
LG Boot Logo
LG Boot Logo
Select the EPK option (software update) and then use the green and yellow buttons to
5
download either SPI Boot or LG Boot Logo. If you checked the LG Boot Logo checkbox, then the Splash image, if selected, will be unchecked. Also, if you select the LG Boot Logo and proceed with the download, the existing Splash image will be deleted.
Ez Download (USB Port1)
[TLL] GlobalClone00001.TLL
[LOGO] 1024X768.jpg
[EPK] M1A_DVB_CN_RevNo1539_v00.00...
[NOSIG] 1360X768.jpg
[NOSIG] Nosignallmage.jpg
[MOV] welcom video.avi
Previous
When you are finished with your selections, use the (->) button to select Apply and then
6
press OK.
[ TV Software Version ] Current : 02.00.00.01 EPK : 02.00.00.01
[ Forced Update Option ] SPI Boot LG Boot Logo
[No Signal Image] Max Size : 10240KB Total Size : 5000KB
Apply
OK
Wait for the download to complete. When it is finished, your TV will be turned off.
7
NOTE
If the DZM file is still in the USB after the download is complete:
- An Ez Download pop-up window will appear and list the file types, such as TLL, LOGO, or EPK, with the previously downloaded lists checked automatically. If the global TLL and model TLL files exist in the same USB root directory, then only the global TLL
will be shown. If the global TLL has been deleted, then the model TLL will be shown.
13
USB Cloning
An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead.
Introduction
(1) Overview USB Cloning Procedure
Commercial TVs have the capability to support cloning internal TV data and programme information
with an external clone device called “USB Cloning”, in order to copy TV data accurately and quickly. The clone internal functions use slightly different internal processes for the two types of commercial TVs. However, the UI of cloning feature remains the same in both. Regarding the demands over the current cloning feature for quicker clonin g, better portability and etc, we would like to announce the cloning process via USB port, named as USB Cloning. USB cloning process is divided into 2 main processes. One is writing the previously saved TV data into the TV, and one another is reading of current TV data into USB memory card. To avoid any confusion due to the words, it is clearly specified as “Receive from USB” and “Send to USB” in the whole process.
(2) Data To Be Cloned
The data cloned are the same data cloned by previous USB Cloning. Details are explained in the
following:
1. TV data includes: A. Installer Menu settings B. Main menu settings (Audio, Picture etc)
2. Analog / Digital Channel information includes: A. Channel numbers B. Channel label C. Channel attributes including channel type, skipping status and etc.
(3) Input Source
The user needs a USB memory card with FAT formatted to make successive cloning via USB port.
A USB memory card size more than 128 Mega Bytes and less than 4 Giga Bytes is recommended.
NOTE
Currently, support the preceding USB file system for FAT file format only. Other file formats
including NTFS is not currently supported. Microsoft Windows officially supports FAT for the USB memory card.
14
Receive From USB
Image shown may differ from your TV.
Plug USB memory card into the USB port of the TV.
1
Use the button to select the TV Manager option and then press the OK button.
2
Installation Menu (V 3.0)
LG Hotel Mode Setup
TV Manager
Password Change
Set ID Setup
Configuration Setup
Multi Timer
Lock Mode
External Speaker
HCEC Setup
Welcome Video
S/W : 02.00.00.01 Micom : 0.00.84
OK
Use the button to select the USB and Receive from USB and press the OK
3
button.
* Below explains the naming rules for .TTL files.
The supported model line will be in the name of the file but the screen size will be listed as “xx”. This allows TVs having the same chassis model number to use the same ‘*.TTL’ file without regard to the screen size. ex) The name of ‘*.TTL’ file is ‘xxLP360H-TA00000.TLL’ for 32/42LP360C model.
TV Manager
USB
Diagnostics
Previous
Use the button to select the desired *.TTL files name and press the OK button.
4
Receive from USB (USB Port1)
Select file type
Global TLL
Model TLL
GlobalClone00001.TLL
Ez Download
Receive from USB
Send to USB
Logo Image Download
OK
Previous
The TV is changed to Standby mode after a successful download.
5
If the download failed, the TV will changed to the initial installation screen.
OK
15
Loading...
+ 35 hidden pages