LG 55LD650 Owner’s Manual

OWNER’S MANUAL

The model and serial number of the TV is located
on the back and one side of the TV.
Record it below should you ever need service.

MODEL

SERIAL

The extended owner’s manuals that contain informa­tion on the advanced features of this LG TV are
located on the CD-ROM provided in an electronic
version.
To read these files, you will need to use the personal
computer (PC) equipped with a CD-ROM drive.

LG Customer Information Center

For inquires or comments, visit www.lg.com or call;

1-888-542-2623
1-800-243-0000
1-888-865-3026

CANADA
USA, Consumer
USA, Commercial

Register your product Online!

www.lg.com

(Except LCD TV, Plasma TV, 32LE5400, 47LE5350, 42/55LX6500)

This product qualifies for ENERGY STAR in the
“factory default (Home Use)” setting.
Changing the factory default settings or enabling other
features may increase power consumption that could
exceed the limits necessary to quality for ENERGY STAR.

LED LCD TV / LCD TV
PLASMA TV

Please read this manual carefully before operating
your set and retain it for future reference.

LCD TV MODELS

32LD550
42LD550
46LD550
52LD550
60LD550

P/NO : MFL62882706 (1109-REV05)

47LD650
55LD650

LED LCD TV MODELS

32LE5400
42LE5400
47LE5400
55LE5400
42LE5350
47LE5350

42LE5500
47LE5500
55LE5500
42LE7500
47LE7500
55LE7500

47LE8500
55LE8500
42LX6500
47LX6500
55LX6500

PLASMA TV MODELS

50PK750
60PK750

www.lg.com

WARNING / CAUTION

TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral trian­gle, is intended to alert the user to

the presence of uninsulated “dan­gerous voltage” within the product’s enclo­sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert

the user to the presence of impor-

tant operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guide­lines for proper grounding and, in particular, speci­fies that the cable ground shall be connected to the
grounding system of the building, as close to the
point of the cable entry as practical.

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC Notice

Class B digital device

This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable pro­tection against harmful interference in a residen­tial installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encour­aged to try to correct the interference by one or
more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equip­ment and receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is con­nected.

- Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two condi-

tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation (of the
device).

Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this product.

IMPORTANT INFORMATION TO PREVENT “IMAGE
BURN / BURN-IN” ON YOUR TV SCREEN

ꔛ

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on
the TV for an extended period, it can become permanently imprinted on the screen. This phenom­enon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s
warranty.

ꔛ

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged
period (2 or more hours for LCD, 1 or more
hours for Plasma).

ꔛ

Image burn can also occur on the letter­boxed areas of your TV if you use the 4:3
aspect ratio setting for an extended period.

2

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

1

Do not use this apparatus
near water.

Clean only with dry cloth.

2

Do not block any ventilation

3

openings. Install in accordance
with the manufacturer’s
instructions.

Do not install near any heat

4

sources such as radiators, heat
registers, stoves, or other appa­ratus (including amplifiers) that
produce heat.

Do not defeat the safety pur-

5

pose of the polarized or ground­ing-type plug. A polarized plug
has two blades with one wider
than the other. A grounding
type plug has two blades and a
third grounding prong, The wide
blade or the third prong are
provided for your safety. If the
provided plug does not fit into
your outlet, consult an electri­cian for replacement of the
obsolete outlet.

Protect the power cord from

6

being walked on or pinched
particularly at plugs, conve­nience receptacles, and the
point where they exit from the
apparatus.

Only use attachments/acces-

7

sories specified by the manu­facturer.

Use only with the cart, stand,

8

tripod, bracket, or table speci­fied by the manufacturer, or
sold with the apparatus. When
a cart is used, use caution
when moving the cart/appara­tus combination to avoid injury
from tip-over.

Refer all servicing to qualified service per­sonnel. Servicing is required when the appa-

10

ratus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not oper­ate normally, or has been dropped.

Never touch this apparatus or antenna dur-

11

ing a thunder or lighting storm.

When mounting a TV on the wall, make sure

12

not to install the TV by the hanging power
and signal cables on the back of the TV.

Do not allow an impact shock or any objects

13

to fall into the product, and do not drop
onto the screen with something.

CAUTION concerning the Power Cord:

14

It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appli­ance and has no additional outlets or
branch circuits. Check the specification
page of this owner's manual to be certain.

Do n ot connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.

Do not overload wall outlets. Overloaded
wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or
damaged or cracked wire insulation are
dangerous . Any of these conditions could
result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deteriora­tion, unplug it, discontinue use of the appli­ance, and have the cord replaced with an
exact replacement part by an authorized
servicer. Protect the power cord from phys­ical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to
plugs, wall outlets, and the point where the
cord exits the appliance.

Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug
when unplugging the power cord. Do not
pull on the power cord to unplug the TV.

Unplug this apparatus during

9

lighting storms or when unused
for long periods of time.

3

SAFETY INSTRUCTIONS

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

WARNING - To reduce the risk of

15

fire or electrical shock, do not
expose this product to rain,
moisture or other liquids. Do not
touch the TV with wet hands. Do
not install this product near
flammable objects such as gas­oline or candles or expose the
TV to direct air conditioning.

Do not expose to dripping or

16

splashing and do not place
objects filled with liquids, such
as vases, cups, etc. on or over
the apparatus (e.g. on shelves
above the unit).

GROUNDING

17

Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV with
a three-prong grounded AC plug must be con­nected to a three-prong grounded AC outlet). If
grounding methods are not possible, have a
qualified electrician install a separate circuit
breaker.

Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.

Power
Supply

Short-circuit

Breaker

DISCONNECTING DEVICE FROM MAINS

18

Mains plug is the disconnecting device. The
plug must remain readily operable.

As long as this unit is connected to the AC

19

wall outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.

Cleaning

20

When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may
occur. Do not clean with chemicals such as
alcohol, thinners or benzene.

Moving

21

Make sure the product is turned off, unplugged
and all cables have been removed. It may
take 2 or more people to carry larger TVs. Do
not press against or put stress on the front
panel of the TV.

ANTENNAS

22

Outdoor antenna grounding

If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna sys­tem should not be located in the vicinity of
overhead power lines or other electric light
or power circuits, or where it can come in
contact with such power lines or circuits as
death or serious injury can occur.

Be sure the antenna system is grounded so
as to provide some protection against volt­age surges and built-up static charges.

Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information
with respect to proper grounding of the
mast and supporting structure, grounding
of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna discharge unit, connection to
grounding electrodes and requirements for
the grounding electrode.

Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70

NEC: National Electrical Code

Ventilation

23

Install your TV where there is proper ventila­tion. Do not install in a confined space such
as a bookcase. Do not cover the product
with cloth or other materials (e.g.) plastic
while plugged in. Do not install in exces­sively dusty places.

Take care not to touch the ventilation open-

24

ings. When watching the TV for a long
period, the ventilation openings may
become hot.

If you smell smoke or other odors coming

25

from the TV, unplug the power cord contact
and authorized service center.

Do not press strongly upon the

26

panel with hand or sharp object
such as nail, pencil or pen, or
make a scratch on it.

Keep the product away from direct sunlight.

27

4

Dot Defect

28

The Plasma or LCD panel is a high technol­ogy product with resolution of two million to

six million pixels. In a very few cases, you
could see fine dots on the screen while

you’reviewing the TV. Those dots are deacti­vated pixels and do not affect the perfor­mance and reliability of the TV.

Generated Sound

29

“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is gener­ated by plastic thermal contraction due to
temperature and humidity. This noise is com­mon for products where thermal deformation
is required.

Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies
depending on the product.

This generated sound does not affect the
performance and reliability of the product.

For LED LCD TV/LCD TV

30

If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.

Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor’s performance.

Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary dis­tortion effects on the screen.

Viewing 3D Imaging (For 3D TV)

31

►When viewing 3D imaging, watch the TV

from an effective viewing angle and with­in the appropriate distance. If you exceed
this viewing angle or distance, you may not
be able to view the 3D imaging. Further­more, the 3D imaging may not display if it
is viewed while you are lying down.

►If you watch the 3D imaging too closely or

for a long period of time, it may harm your
eyesight.

►Watching the TV or playing video games

that incorporate 3D imaging with the 3D
glasses for a long period of time can cause
drowsiness, headaches or fatigue to you
and/or your eyes. If you have a headache,
or otherwise feel fatigued or drowsy, stop
watching the TV and take a rest.

►Pregnant woman, seniors, persons with

heart problems or persons who experience
frequent drowsiness should refrain from
watching 3D TV.

►Some 3D imaging may cause you to duck

or dodge the image displayed in the video.
Therefore, it is best if you do not watch 3D
TV near fragile objects or near any objects
that can be knocked over easily.

► Please prevent children under the age of

5 from watching 3D TV. It may affect their
vision development.

►Warning for photosensitization seizure:

Some viewers may experience a seizure

or epilepsy when exposed to certain fac­tors, including fl ashing lights or images
in TV or video games. If you or anybody
from your family has a history of epilepsy
or seizure, please consult with your doc­tor before watching 3D TV.

Also certain symptoms can occur in un-

specifi ed conditions without any previ­ous history. If you experience any of the
following symptoms, immediately stop
watching the 3D imaging and consult
a doctor: dizziness or lightheadedness,
visual transition or altered vision, visual
or facial instability, such as eye or muscle
twitching, unconscious action, convulsion,
loss of conscience, confusion or disorien­tation, loss of directional sense, cramps,
or nausea. Parents should monitor their
children, including teenagers, for these
symptoms as they may be more sensitive
to the effects of watching 3D TV.

Risk of photosensitization seizure can be

reduced with the following actions.

- Take frequent breaks from watching 3D
TV.

- For those who have vision that is differ-

ent in each eye, they should watch the
TV after taking vision correction meas­ures.

- Watch the TV so that your eyes are on

the same level as the 3D screen and
refrain from sitting too closely to the TV

- Do not watch the 3D imaging when

tired or sick, and avoid watching the 3D
imaging for a long period of time.

- Do not wear the 3D glasses for any oth-

er purpose than viewing 3D imaging on
a 3D TV.

- Some viewers may feel disoriented after

watching 3D TV. Therefore, after you watch
3D TV, take a moment to regain aware­ness of your situation before moving.

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product con­tains a small amount of mercury. Do not
dispose of this product with general house­hold waste. Disposal of this product must be
carried out in accordance to the regulations of
your local authority.

5

CONTENTS

!

MENU

CONTENTS

WARNING / CAUTION
SAFETY INSTRUCTIONS

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Stand Instruction
VESA Wall Mounting
Desktop Pedestal Installation
Cable Management
Swivel Stand
Attaching the TV to a Desk
Kensington Security System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

. . . . . . . . . . . . . . . . . . . . . . . 2

. . . . . . . . . . . . . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

. . . . . . . . . . . . . . . . . . . . . 13

. . . . . . . . . . . . . . . . . . . . . . . 15

. . . . . . . . . . . . . . . . . . . . . . 15

NETCAST

Netcast Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3D IMAGING

3D Technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Watching 3D Imaging

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WATCHING TV

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Initial Setting
On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

. . . . . . . . . . . . . . . . . . . . 30

APPENDIX

EXTERNAL EQUIPMENT SETUP

Connecting your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

NETWORK

Network Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Maintenance
Open Source Software Notice
Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

. . . . . . . . . . . . . . . . . . 34

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

HOW TO USE THE OWNER'S MANUAL ON THE CD-ROM

To view the Owner's Manual on the CD-ROM, Adobe Acrobat Reader must be installed on your PC.
The “ACRORD" folder on the CD-ROM contains the installation programs for them.
If you want to install those programs, Open the “My Computer”
“ACRORD”

➜ double-click your language.

➜ Open the “LG”➜ Open the

TO VIEW THE OWNER'S MANUAL ON THE CD-ROM

The Owner's Manual files are included in the supplied CD-ROM.
Load the supplied CD-ROM into the CD-ROM drive of your PC.
After a while, the web page of the CD-ROM will open automatically. (for Window only)

➜

When you click, display the PDF file.

NOTE

►If the web page does not appear automatically, open the Owner's Manual file

directly.

Open the “My computer”

➜

You can find the
desired contents
easily using the
bookmark.

➜ Open the “LG”➜ Open the “index.htm” file.

TO VIEW THE SIMPLE MANUAL

You can easily and effectively access the TV information by viewing a simple manual on the TV.

1

GREEN

Select
Simple Manual.

➜

2

Select the part of the manual you
want to see.

6

PREPARATION

1.5V 1.5V

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please con­tact the dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner’s Manual CD Manual,

Nero MediaHome 4

Essentials CD

Not included with all models

* Wipe spots on the exterior only

with the polishing cloth.

* Do not wipe roughly when remov-

Polishing Cloth

ing stains. Excessive pressure may
cause scratches or discoloration.

Not included with all models

Ferrite core can be used to reduce the electromagnetic
waves that may interfere with the TV. Install the Ferrite
core on the power cable close to the wall plug.

Ferrite Core

(Black)

Ferrite core can be used to reduce the electromagnetic
wave when connecting the LAN cable. Place the ferrite

Ferrite Core

core far from TV and wind the LAN cable in the ferrite
core once.

(White)

Remote Control,

Batteries (AAA)

Option Extras

D-sub 15 pin Cable

When using the VGA (D-sub 15
pin cable) PC connection, the
user must use shielded signal
interface cables with ferrite cores
to maintain standards compli­ance.

Close to the wall plug.

50/60PK750

(For 50PK750)

x 3 x 4

(M5 x 14) (M4 x 28)

Screws for stand assembly

(Refer to P.9)

x 2

Cable Holder
(Refer to p.14)

Protection Cover

(Refer to p.9)

Power Cord

7

32/42/46/52/60LD550, 47/55LD650

1.5V 1.5V

CH

FLASHBK

VOL

POWER TV/INPUT

x 8

(M4 x 20)

(For 32/42LD550)

Screws for stand assembly

(Refer to P.10)

Screw for stand fixing

(Refer to P.15)

Protection Cover

(Refer to P.10)

Power Cord

42/47LE5350, 32/42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500, 47/55LE8500, 42/47/55LX6500

(47/55LE8500) (Other models)(55LE5400/5500/7500,

55LX6500, 42LE5350)

(47LE5350)

x 8 x 8x 4 x 4x 4 x 4

(M4 x 20) (M4 x 16)(M4 x 16) (M4 x 16)(M4 x 24) (M4 x 26)

Cable Holder
(Refer to p.14)

Screws for stand assembly (Refer to P.11)

x 2

(For 42/47/55LE7500,

47/55LE8500)

Component gender cable,

(For 42/47/55LE7500)

AV gender cable

Cleansing Cloths

(mitt)

* Wipe spots on the exterior only with the cleasing cloths.
* Do not wipe roughly when removing stains. Excessive pres-

sure may cause scratches or discoloration.

* For cleaning front frame, please slowly wipe in one direction

after spraying water 1-2 times on cleansing cloths. Please
remove excessive moisture after cleaning. Excessive mois­ture may cause water stains on the frame.

Simple Remote Control,

Batteries (AAA)

(For 32LE5400)

Screw for stand fixing

(Refer to P.15)

8

OPTIONAL EXTRAS

Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
This device only works with compatible LG LED LCD TV, LCD TV, or Plasma TV.

(For 42/47/55LX6500)(Except 42/47LE5350) (Except 42/47LE5350)

Wireless Media Box

(AN-WL100W)

Wireless LAN for Broadband/

DLNA Adaptor

(AN-WF100)

3D Glasses

(AG-S100)

STAND INSTRUCTIONS

!

ꔛ

Image shown may differ from your TV.

(For 50/60PK750)

INSTALLATION (For 50PK750)

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

Assemble the parts of the STAND BODY

2

with the STAND BASE of the TV.

STAND BODY

M5 x 14

Assemble the TV as shown.

3

STAND BASE

DETACHMENT

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

Remove the screws that hold the stand on.

2

50PK750 60PK750

M4 x 28

Detach the stand from TV.

3

M4 x 30

PROTECTION COVER

After removing the stand, install the included

4

Install the 4 screws into the holes shown.

M4 x 28

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If
not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.

PROTECTION COVER over the hole for the
stand.

Press the PROTECTION COVER into the TV until
you hear it click.

When installing the wall mounting bracket, use
the PROTECTION COVER.

PROTECTION COVER

Fix a guide to the outside.

9

PREPARATION

!

A

C
IN

CA

BLE MANAGEMENT

AC IN

CABLE MANAGEMENT

AC IN

CABLE MANAGEMENT

AC IN

CABLE MANAGEMENT

AC IN

CABLE MANAGEMENT

AC

IN

C
AB

L
E
MA

N
AGE

M
ENT

STAND INSTRUCTIONS

ꔛ

Image shown may differ from your TV.

(For 32/42/46/52/60LD550, 47/55LD650)

INSTALLATION

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

Assemble the parts of the STAND BODY

2

with the STAND BASE of the TV.

STAND BODY

M4 x 20

STAND BASE

DETACHMENT

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

Remove the screws that hold the stand on.

2

Detach the stand from TV.

3

10

Assemble the TV as shown.

3

PROTECTION COVER

4

Install the 4 screws into the holes shown.

NOTE

► When assembling the desk type stand,

make sure the screws are fully tightened (If
not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.

After removing the stand, install the included
PROTECTION COVER over the hole for the
stand.

Press the PROTECTION COVER into the TV until
you hear it click.

When installing the wall mounting bracket, use
the PROTECTION COVER.

!

STAND INSTRUCTIONS

(For 42/47LE5350, 32/42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500, 47/55LE8500,
42/47/55LX6500)

ꔛ

Image shown may differ from your TV.

INSTALLATION

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

Assemble the parts of the STAND BODY

2

with the STAND BASE of the TV. At this
time, tighten the screws that hold the
STAND BODY on.

DETACHMENT

Carefully place the TV screen side down on

1

a cushioned surface to protect the screen
from damage.

STAND BODY

M4 x 20

(47/55LE8500)

M4 x 16

(Other models)

Assemble the TV as shown.

3

Assemble the part of the STAND REAR

4

COVER with the TV.

STAND REAR

M4 x 24

(55LE5400/5500/7500,

55LX6500, 42LE5350)

M4 x 26

(47LE5350)

COVER

STAND BASE

Remove the screws that hold the stand on.

2

Detach the STAND REAR COVER from TV.

3

Detach the stand from TV.

4

5

Install the 4 screws into the holes shown.

M4 x 20

(47/55LE8500)

M4 x 16

(Other models)

NOTE

► When assembling the desk type stand, make sure the screws are fully tightened (If not tightened

fully, the TV can tilt forward after the product installation). Do not over tighten.

11

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building mate­rials, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

Model

32LD550,

32LE5400

42/46LD550,

47LD650,
42/47LE5350,
42/47LE5400,
42/47LE5500,

42/47LE7500,

47LE8500,

42/47LX6500

52LD550, 55LD650,

55LE5400,

55LE5500,
55LE7500,

55LE8500,

60LD550,

55LX6500

50PK750 400

VESA (A * B)

A

B

20

0

100 M4 4 LSW100B, LSW100BG

*

200

200 M6 4 LSW200B, LSW200BG

*

400

400 M6 4 LSW400B, LSW400BG

*

400 M6 4 PSW400B, PSW400BG

*

Standard

Screw

Quantity

Wall Mounting Bracket

(sold separately)

12

60PK750 600

400 M8 4 PSW600B, PSW600BG

*

!

NOTE

► Screw length needed depends on the wall

mount used. For further information, refer to
the instructions included with the mount.

► Standard dimensions for wall mount kits are

shown in the table.

► When purchasing our wall mount kit, a detailed

installation manual and all parts necessary for
assembly are provided.

► Do not use screws longer than the standard

dimension, as they may cause damage to the
inside to the TV.

► For wall mounts that do not comply with the

VESA standard screw specifications, the length
of the screws may differ depending on their
specifications.

► Do not use screws that do not comply with the

VESA standard screw specifications.

Do not use fasten the screws too strongly, this

may damage the TV or cause the TV to a fall,
leading to personal injury. LG is not liable for
these kinds of accidents.

► LG is not liable for TV damage or personal

injury when a non-VESA or non specified wall
mount is used or the consumer fails to follow
the TV installation instructions.

CAUTION

► Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to

electric shock.

DESKTOP PEDESTAL INSTALLATION

ꔛ

Image shown may differ from your TV.

For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall.

10.1 cm (4 inch)

10.1 cm (4 inch)

10.1 cm (4 inch)

CAUTION

► Ensure adequate ventilation by following the clearance recommendations.
► Do not mount near or above any type of heat source.

10.1 cm (4 inch)

13

PREPARATION

AC IN

AC IN

AC IN

CABLE MANAGEMENT

ꔛ

Image shown may differ from your TV.

32/42/46/52/60LD550, 47/55LD650

Connect the cables as necessary.

1

To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.

Open the CABLE MANAGEMENT CLIP as

2

shown.

Plasma TV

After connecting the cables as necessary,
install the CABLE HOLDER as shown and

1

bundle the cables.
In case of the LAN cable, install as shown

to reduce the electromagnetic wave.

CABLE HOLDER

42/47LE5350, 32/42/47/55LE5400,
42/47/55LE5500, 42/47/55LE7500,
47/55LE8500, 42/47/55LX6500

Secure the power cord with the CABLE
HOLDER on the TV back cover.

1

It will help prevent the power cable from
being removed by accident.

14

CABLE MANAGEMENT CLIP

Put the cables inside the CABLE

3

MANAGEMENT CLIP and snap it closed.

CABLE HOLDER

After connecting the cables as necessary,

2

install the CABLE HOLDER as shown and
bundle the cables.

CABLE HOLDER

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 º to suit
your viewing position.

ATTACHING THE TV TO A DESK

ꔛ

Image shown may differ from your TV.

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, poten-

tially causing injury or damaging the product.

1-Screw
( provided as parts of the product)

(For

32/42LD550, 32LE5400

Stand

Desk

)

WARNING

► To prevent TV from falling over, the TV should be securely attached to the floor/wall per installa-

tion instructions. Tipping, shaking, or rocking the machine may cause injury.

KENSINGTON SECURITY SYSTEM

ꔛ

This feature is not available for all models.

- The TV is equipped with a Kensington Security System con­nector on the back panel. Connect the Kensington Security
System cable as shown below.

- For the detailed installation and use of the Kensington Security

System, refer to the user’s guide provided with the Kensington
Security System.

For further information, contact http://www.kensington.com,

the internet homepage of the Kensington company. Kensington
sells security systems for expensive electronic equipment such
as notebook PCs and LCD projectors.

NOTE: The Kensington Security System is an optional accessory.

15

RGB IN (PC)

LAN

WIRELESS
CONTROL

(RGB/DVI)

RS-232C IN

(

SERVICE ONLY)

OPTICAL
DIGITAL

/DVI IN

2

3

1

VIDEO

AUDIO

L(MONO)

R

AV IN 1

AUDIO IN

AUDIO OUT

VIDEO

AUDIO

COMPONENT IN

YPB PR

L R

2

1

Y L RPB PR

ꔡ

S-VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

RGB IN (PC)

LAN

(RGB/DVI)

/DVI IN

2

3

1

VIDEO

AUDIO

COMPONENT IN

AUDIO IN

AUDIO OUT

2

1

VIDEO

AUDIO

L(MONO)

R

AV IN 1

YPBP

R

L R

OPTICAL DIGITAL

(

SERVICE ONLY)

L R

VIDEO

AUDIO

HDMI OUTPUT

RGB IN (PC)

LAN

WIRELESS
CONTROL

(RGB/DVI)

VIDEO

L(MO

VIDEO

AUDIO IN

AUDIO OUT

2

1

/DVI IN

2

3

1

YPBP

R

OPTICAL DIGITAL

(

SERVIC

L R

DVI OUTPUT

AUDIO

RGB IN (PC)

LAN

WIRELESS
CONTROL

RS-232C IN

(

SERVICE ONLY)

VIDEO

AUDIO

L(MONO)

R

VIDEO

AUDIO

COMPONENT INAV IN 1

YPBP

R

L R

AUDIO OUT

2

1

/DVI IN

2

3

1

(RGB/DVI)

AUDIO IN

OPTICAL DIGITAL

ꔡ

EXTERNAL EQUIPMENT SETUP

ANTENNA/
CABLE IN

RGB IN (PC)

LAN

WIRELESS

CONTROL

(RGB/DVI)

OPTICAL DIGITAL

/DVI IN

2

3

1

VIDEO

AUDIO

L(MONO)

R

VIDEO

AUDIO

COMPONENT INAV IN 1

YPB PR

L R

AUDIO IN

AUDIO OUT

2

1

RS-232C IN

(

SERVICE ONLY)

ꔡ

PREPARATION

CONNECTING YOUR TV

To connect an additional equipment, see the External Equipment Setup section in CD Manual.

* Typical Layout

Connection Order

HDMI is the best way to connect a
device. If it's not available, move down
the list in order until you find a con­nection that's available on each device.

1

2

HDMI
DVI

3

Component

4

Composite

16

1

2

HDMI

DVI

You can use a adapter to connect
DVI to HDMI, but you will only
have 2 channel stereo for sound.
The adapter is not needed when
connecting a PC.

Use HDMI to connect
external devices when
available. If not avail­able, use DVI or
Component.

Sorry, A phone
Jack to stereo

0.32 cm (1/8")
headphone plug
adapter is not
included. It is
available from
most stores that
carry electronics.

3

4

Component

Composite

Use Composite
for the video
connection if
available.

Match the jack
colors.

Antenna/Cable

Use this connection when you need to
connect directly to an antenna or cable
system instead of using a cable box.

Antenna

Cable TV

OR

Be careful not

RF Coaxial

Wire (75 Ω)

to bend the
copper wire.

ANTENNA/

CABLE IN

Make sure
you don't
mix up the
colors.

NETWORK

NETWORK SETUP

Wired Network Connection

This TV can be connected to a local area network (LAN) via the LAN port. After making the physical
connection, the TV needs to be set up for network communication.

Broadband modem

1. How to connect

Connect the LAN port of the Modem or Router to the LAN port on the TV.

1

LAN

ꔡ

WIRELESS

CONTROL

1

/DVI IN

3

2

1

Broadband Service

RGB IN (PC)

(RGB/DVI)

AUDIO IN

2

YPBP

1

OPTICAL DIGITAL

AUDIO OUT

VIDEO

RS-232C IN

(

SERVICE ONLY)

VIDEO

R

L(MONO)

L R

AUDIO

AUDIO

R

COMPONENT INAV IN 1

Router

Broadband modem

Broadband Service

2. How to use

ꔛ

Select “Network Setting” in the NETWORK menu.

ꔛ

After connecting the LAN port, use the NETCAST menu.

ꔛ

For more information about NETCAST setup and troubleshooting, visit our Knowledgebase at
LGknowledgebase.com. Search for NetCast.

CAUTION

► Do not connect a modular phone cable to the LAN port.
► Since there are various connection methods, please follow the specifications of your telecommu-

nication carrier or internet service provider.

17

NETWORK

MENU

ENTER

ENTER

ENTER

ENTER

12

ABC3 DEF

4

GHI5 JKL6

MNO

7

PQRS8 TUV

0

9

WXYZ

ENTER

Wired Network Setup

If wired and wireless networks are both available, wired is the preferred method.
After making a physical connection, a small number of home networks may require the TV network

settings to be adjusted.
For detail information, contact your internet provider or router manual.

If you already set

NETWORK

• Network Setting : Wired

• Network Status : Internet is connected

• Legal Notice

• ESN

ꔂ Move ꔉ Enter

Network Type

Wired network is recommended

Wired

Wireless

Appeared when wired and
wireless are simultaneously
connected.

the Network Setting

Previous setting value exists. Do
you want to connect with the
previous setting?

Enter

Resetting

ꔉ Next

ꕯ Exit

2

3

4

5

6

IP Auto Setting

Network Status

TV

Network connecting

Setting Test Close

1

Select NETWORK.

Network Setting

Select the IP setting mode.
IP Mode

ꔈIP Address 255 . 255 . 0 . 0

ꔈSubnet Mask 255 . 255 . 0 . 0

ꔈGateway 255 . 255 . 0 . 0

ꔈDNS Server 255 . 255 . 0 . 0

ꕉ Previous

◀ IP Auto Setting ▶

Enter

ꔛ

This feature requires an always-on
broadband internet connection.

ꔛ

You do not need to connect to a PC

ꕯ Exit

IP Manual Setting

Network Setting

Insert the IP address.
IP Mode

ꔈIP Address 255 . 255 . 0 . 0

ꔈSubnet Mask 255 . 255 . 0 . 0

ꔈGateway 255 . 255 . 0 . 0

ꔈDNS Server 255 . 255 . 0 . 0

◀ IP Manual Setting ▶

Enter

ꕉ Previous

ꕯ Exit

to use this function.

Select Network Setting.

ꔛ

If Network Setting is not working,
check your network conditions. Check
the LAN cable and make sure your

Select Wired.

If you already set Network Setting:
Select Resetting. The new connection
settings resets the current network
settings.

Select IP Auto Setting or IP Manual
Setting.

When Selecting IP Manual Setting:
IP addresses will need to be input

manually.

router has DHCP turned on if you
wish to use the Auto Setting.

ꔛ

If the Network Setting is not com­pleted, network may not operate nor­mally.

ꔛ

IP Auto Setting: Select it if there is a
DHCP server on the local area net­work (LAN) via wired connection, the
TV will automatically be allocated an
IP address. If you’re using a broad­band router or broadband modem
that has a DHCP (Dynamic Host
Configuration Protocol) server func­tion. The IP address will automatically
be determined.

ꔛ

IP Manual Setting: Select it if there is
no DHCP server on the network and
you want to set the IP address manu-

Select Enter.

ally.

18

!

NOTE

► For more information about NETCAST setup

and troubleshooting, visit http://lgknowledge­base.com. Search for NETCAST.

► Use a standard LAN cable with this TV. Cat5

or better with a RJ45 connector.

► Many network connection problems during set

up can often be fixed by re-setting the router
or modem. After connecting the player to the
home network, quickly power off and/or dis­connect the power cable of the home network
router or cable modem. Then power on and/or
connect the power cable again.

► Depending on the internet service provider

(ISP), the number of devices that can receive
internet service may be limited by the appli­cable terms of service. For details, contact your
ISP.

► LG is not responsible for any malfunction of

the TV and/or the internet connection feature
due to communication errors/malfunctions
associated with your broadband internet con­nection, or other connected equipment.

► LG is not responsible for problems within your

internet connection.

► Some content available through the network

connection may not be compatible with the TV.
If you have questions about such content,
please contact the producer of the content.

► You may experience undesired results if the

network connection speed does not meet the
requirements of the content being accessed.

► Some internet connection operations may not

be possible due to certain restrictions set by
the Internet service provider (ISP) supplying
your broadband Internet connection.

► Any fees charged by an ISP including, without

limitation, connection charges are your respon­sibility.

► A 10 Base-T or 100 Base-TX LAN port is

required for connection to this TV. If your inter­net service does not allow for such a connec­tion, you will not be able to connect the TV.

► A DSL modem is required to use DSL service

and a cable modem is required to use cable
modem service. Depending on the access
method of and subscriber agreement with your
ISP, you may not be able to use the internet
connection feature contained in this TV or you
may be limited to the number of devices you
can connect at the same time. (If your ISP
limits subscription to one device, this TV may
not be allowed to connect when a PC is already
connected.)

► The use of a “Router” may not be allowed or

its usage may be limited depending on the
policies and restrictions of your ISP. For details,
contact your ISP directly.

► The wireless network operates at 2.4 GHz radio

frequencies that are also used by other house­hold devices such as cordless telephone,
Bluetooth® devices, microwave oven, and can
be affected by interference from them. It can
be interrupted by the device using 5Ghz radio
frequencies. It is same device with LG wireless
media box, cordless telephone, other Wi-Fi
device.

► It may decrease the service speed using

Wireless network by surrounding wireless con­dition.

► Turn off all unused network equipment in your

local home network. Some devices may gen­erate network traffic.

► In some instances, placing the access point or

wireless router higher up away from the floor
may improve the reception.

► The reception quality over wireless depends on

many factors such as type of the access point,
distance between the TV and access point,
and the location of the TV.

► When connecting internet through the wired/

wireless sharing machine, it may interrupt the
connection because of the use limitation and
confirmation of service company.

► To connect wireless AP, an AP that supports

the wireless connection is necessary, and the
wireless connection function of the AP needs
to be activated. Please enquire to the AP sup­plier for the possibility of AP wireless connec­tions.

► Please verify the security settings of AP SSID

for wireless AP connection, and enquire to the
AP supplier for the AP SSID security settings.

► The TV can become slower or malfunction with

wrong settings of network equipments (wired/
wireless router, hub, etc). Please install cor­rectly by referring to the manual of the equip­ment, and set the network.

►

When AP is set to include 802.11 n, and if
Encryption is designated as WEP(64/128bit)
or WPA(TKIP/AES), the connection may not
be possible. There may be different connec­tion methods according to the AP manufac­turers.

19

NETWORK

IN 4

AV IN 2

VIDEO

AUDIO

L(MONO)

R

H/P

USB IN 1 USB IN 2

!

Wireless Network Connection (Except 42/47LE5350)

The LG Wireless LAN for Broadband/DLNA Adaptor, which is sold separately, allows the TV to connect
to a wireless lan network.

The network configuration and connection method may vary depending on the equipment in use and
the network environment. Refer to the setup instructions supplied with your access point or wireless
router for detailed connection steps and network settings.

1. How to connect

Connect the “LG Wireless LAN for Broadband/DLNA Adaptor (sold separately)” to the USB

1

IN 1 or 2 port on the TV.

2. How to use

ꔛ

Select “Network Setting” in the NETWORK menu.

ꔛ

After connecting, you can use the NETCAST menu.

NOTE

►For enjoying pictures, music, or video stored in the PC using the router, the use of wired port in the

router is recommended.

►When the wireless port of the router is used, there may be restrictions for some functions.

20

Wireless Network Setup (Except 42/47LE5350)

ENTER

ENTER

12

ABC3 DEF

4

GHI5 JKL6

MNO

7

PQRS8 TUV

0

9

WXYZ

ENTER

MENU

ENTER

ENTER

ENTER

ENTER

Setting up the AP (Access Point) or the wireless router is required before connecting the TV to the
network.

If you already set the

NETWORK

• Network Setting : Wired

• Network Status : Internet is connected

• Legal Notice

• ESN

ꔂ Move ꔉ Enter

Network Type

Wired network is recommended

Wired

Wireless

Appeared when wired and wireless

are simultaneously connected.

Network Setting

Previous setting value exists. Do
you want to connect with the
previous setting?

Enter

Resetting

ꔉ Next

ꕯ Exit

Selecting the wireless network setting type

Select the wireless network setting type.

Setting from the AP list

Simple setting (WPS-button mode)

Setting Ad-hoc network

ꔉ Next

ꕉ Previous ꕯ Exit

Network Setting

Select the IP setting mode.
IP Mode

ꔈIP Address 255 . 255 . 0 . 0

ꔈSubnet Mask 255 . 255 . 0 . 0

ꔈGateway 255 . 255 . 0 . 0

ꔈDNS Server 255 . 255 . 0 . 0

ꕉ Previous

◀ IP Auto Setting ▶

Enter

1

2

3

4

5

If your AP is locked

Inserting the security key

Insert the security key of AP.

Insert 8~63 ASCII characters

Enter Cancel

ꕯ Exit

ꕉ Prev.

Select NETWORK.

Select Network Setting.

Select Wireless.

If you already set Network
Setting: Select Resetting.

The new connection settings
resets the current network set­tings.

Select Setting from the AP list.

Selecting AP

Select AP you want to connect.

◀▶

ꕯ Exit

6

Scan the all available AP (Access
Point) or wireless routers within range
and display them as a list.

7

Select an AP (Access Point) or
wireless router on the list.
(If your AP is locked, insert the
security key of AP).

8

Repeat step 4-5 on P.18.

9

Input the security key of AP.

Page 1/1

Input the new SSID

iptime

ASW

Network1

ꔅ Connecting with PIN mode

ꕉ Previous ꕯ Exit

Access Point

Search

ꔉ Next

21

NETWORK

ENTER

ENTER

ENTER

When a security code is already set

PIN (Personal Identification Number)

If you want to connect the AP (Access Point) or router with PIN, use this feature.

Selecting AP

Select AP you want to connect.

Input the new SSID

iptime

ASW

Network1

ꔅ Connecting with PIN mode

ꕉ Previous ꕯ Exit

Repeat step 1-6 on P.21.

1

2

3

Connect the acccess point with PIN

RED

mode.

You can see the Network ID and Security Key

Page 1/1

Access Point

Search

ꔉ Next

on your TV screen.
Enter the PIN number to your device.

Connecting with PIN mode

Insert PIN number at the AP webpage and

press ‘Connect’ button.

PIN NUBMER : 12345670

Connect

For more information, check the AP manual.

ꕉ Previous

4

5

ꔛ

Select Connect.

Repeat step 4-5 on P.18.

PIN number is the unique 8 digit number
of the dongle.

ꔉ Next

ꕯ Exit

22

Simple setting (WPS-button mode)

If your access point or wireless router that supports PIN or WPS (Wi-Fi Protected Setup), it’s available
to use your access point or wireless router within 120 counts. You do not need to know the access
point name (SSID: Service Set Identifier) and security code of your access point or wireless router.

Select the wireless network setting type.

Select the wireless network setting type.

Setting from the AP list

Simple setting (WPS-button mode)

Setting Ad-hoc network

ꕉ Previous ꕯ Exit

Repeat step 1-4 on P.21.

1

2

Select Simple setting (PBC
mode).

ꔉ Next

Simple setting (WPS-button mode)

Press PBC Mode button of AP and press ‘Connect’ button.

Connect

Caution: Check if PBC mode button is available for your AP.

ꕉ Previous

ꔉ Next

ꕯ Exit

3

4

Select Connect.

Repeat step 4-5 on P.18.

ENTER

ENTER

ENTER

ENTER

AD-hoc Mode

ENTER

ENTER

This is the method of communicating directly with the machine to communicate without AP.
This is the same as connecting two PCs with a cross cable.

Selecting the wireless network setting type

Select the wireless network setting type.

Setting from the AP list

Simple setting (WPS-button mode)

Setting Ad-hoc network

ꔉ Next

ꕉ Previous ꕯ Exit

Setting Ad-hoc network

Features using exiting network can be unavailable. Do you

want to change network connection?

Enter Cancel

ꔉ Next

ꕉ Previous ꕯ Exit

Setting Ad-hoc network

Insert the setting information into the device.

Network ID(SSID) : LGTV10
Security Key : 1111111111

ꔅ Changing the setting information.

Connect

ꕉ Previous ꕯ Exit

ꔉ Next

Network Status

Adhoc network is connected.

TV

(LGTV10)

Signal Strength

Mac Address : 00:00:13:64:23:01
IP Address : 10.19.152.115

Gateway

Subnet Mask : 255.255.254.0
Gateway : 10.19.152.1

Setting Test Close

Repeat step 1-3 on P.21.

1

2

Select Setting AD-hoc network.

3

Select Enter.

Network Setting

Insert the IP address.

IP Mode

ꔈIP Address 192 . 168 . 0 . 10

ꔈSubnet Mask 255 . 255 . 255 . 0

ꔈ

Gateway 192 . 168 . 0 . 1

ꔈ

DNS Server 255 . 255 . 0 . 0

ꕉ Previous

ꔛ

PC Setting
Internet Protocol(TCP/IP) of PC needs to be set
manually.
IP address, Subnet Mask, and default Gateway
can be set with your own discretion.
i.e) IP address: 192.168.0.1 / Subnet Mask:

255.255.255.0 / default Gateway: 192.168.0.10

ꔛ

TV Setting
Verify IP address and gateway of PC.
Input Gateway address of PC to IP Address, and

IP Address of PC to Gateway, and select Enter.
i.e) IP address: 192.168.0.10 / Subnet Mask:

255.255.255.0 / default Gateway: 192.168.0.1

IP Manual Setting

Enter

ꕯ Exit

5

6

Setting Ad-hoc network

Insert the setting information into the device.

Network ID(SSID) : LGTV10
Security Key : 1111111111

Connecting the Ad-hoc network

Cancel

ꔛ

Example of the PC setting that
supports a wireless network

1. Find a wireless network device in
your PC.

2. Select LGTV10 that appears in
the list. (Select the same name
as the network ID that appears
on your TV screen.)

3. Type 1111111111 in the Inserting

the security key dialog.

(Type the security key that

appears on your TV screen.)

Insert the IP address.

Network setting is completed.
Select Close.

4

Select Connect to connect Ad-hoc network.
You can see the Network ID and Security Key
on your TV screen.
Enter this Network ID and Security Key to
your device.

If a network may not operate, change the
setting information using the RED button.

23

NETCAST

ENTER

!

NETCAST

NETCAST MENU

These services are provided by separate Content Provider.
NETCAST menu source can differ by country.

What is a NETCAST?

Stream movies, TV shows and video, and get up to the minute news, stock information and weather
updates directly to your TV.

ꔛ

To view the owner’s manual that provided by
the Content Provider, visit our website at
http://www.lg.com.

ꔛ

To see the activation method of Yahoo!,
Netflix, or Vudu, click the Yahoo!, Netflix,

Vudu in the CD manual (For USA).

1

ꔛ

Yahoo! (For USA)

Yahoo! TV Widgets give you the best of the
Internet in perfect harmony with the simplicity and
reliability of your TV. TV Widgets deliver a Cinematic
internet
web services for viewing on the TV.

ꔛ

You can instantly watch movies (quite a few new
releases) & TV episodes from Netflix streamed
over the internet to your TV.

To become a Netflix member visit: www.netflix.
com/LG

Note that this service is provided by the Content
Provider, Netflix. It is dependent on Netflix to pro­vide the data.

ꔛ

In order to make rental/purchase transactions on
the Vudu service, a user must create an account
on vudu.com.

That account is linked to a specific device, via a
process called “activation”. It is possible to have
multiple devices associated with a single Vudu
account.

Note that this service is provided by the Content
Provider, Vudu. It is dependent on Vudu to pro­vide the data.

TM

Netflix (For USA)

Vudu (For USA)

Select NETCAST menu option.

experience by converting your favorite

2

Enjoy the online service.

ꔛ

YouTube

YouTube is a video sharing website where users
can upload, view, and share video clips.

ꔛ

Picasa

Picasa is a photo organizing, editing or sharing
website where users can upload, view, and share
photos.

NOTE

► The videos list searched from the TV may

different with the list searched from a web
browser on PC.

► The settings of this TV do not affect the

YouTube’s playback quality.

► The playback of videos may be paused,

stopped or buffering occurring often
depending on your broadband speed.

► For service that requires log in, join the

applicable service on the website using the
PC and log in through the TV to enjoy vari­ous additional functionalities.

► When you set the city you want with Setup

by pressing the red button, the background
of NetCast will be set to the weather of the
selected city.

► For Plasma TV: If there is no user action 2

minutes following freezing image or video
on screen, the screensaver will activate itself
preventing fixed image remaining on screen.

24