LG 52LG50DC, 47LG50DC-UA, 42LG30DC, 37LG30DC User Manual

Please read this manual carefully before operating
your set.

Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.

LCD TV
OWNER’S MANUAL

32LG30DC
37LG30DC
42LG30DC

47LG50DC
52LG50DC

P/NO : SAC30708017 (0809-REV02)

www.lgcommercial.com

As an ENERGY STAR Partner
LG Electronics USA, Inc.
has determined that this
product meets the ENERGY
STAR guidelines for energy
efficiency.

ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency (EPA).

2

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the litera­ture accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

3

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers)that produce
heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com­bination to avoid injury from tip-over.

Unplug this apparatus during lighting storms
or when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power­supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.

1

2

3

4

5

7

6

8

9

10

4

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during
a thunder or lighting storm.

When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.

Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.

CAUTION concerning the Power Cord:
It is recommend that appliances be placed

upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.

Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.

Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).

GGRROOUUNN DD II NNGG

Ensure that you connect the earth ground wire
to prevent possible electric shock. (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC
outlet) If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS

Mains plug is the disconnecting device. The
plug must remain readily operable.

Keep the product away from direct sunlight.

12

11

14

13

16

17

18

19

Power
Supply

Short-circuit

Breaker

15

5

AANN TT EENN NNAASS
OOuuttddoooorr aann tteennnnaa ggrroouunn ddiinngg

If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.

Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.

Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes and requirements for the grounding
electrode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700

CC lleeaa nniinngg

When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.

MMoovvii nngg

Make sure the product is turned off,
unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.

VVeennttiillaatt iioonn

Install your TV where there is proper ventilation.
Do not install in a confined space such as a
bookcase. Do not cover the product with cloth
or other materials (e.g.) plastic while plugged
in. Do not install in excessively dusty places.

If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the
power cord contact an authorized service center.

Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.

22

20

23

24

25

21

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

6

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 3

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

Stand Instruction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14

Cable Management

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

15

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Attaching the TV to a Desk

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Securing the TV to the wall to prevent falling when
the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . .

18

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

USB Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

Audio Out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

WATCHING TV / CHANNEL CONTROL

Remote Control Functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On the TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

36

Quick Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

Initial Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 42

- Add / Delete Channel (Manual Tuning) . . . . . . 43

- Channel Editing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Input Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

AV Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

SIMPLINK

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48

USB

Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

PICTURE CONTROL

Picture Size (Aspect Ratio) Control

. . . . . . . . . . . . . . . . . . 58

Preset Picture Settings

- Picture Mode - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60

- Color Tone - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Manual Picture Adjustment

- Picture Mode - User Mode

. . . . . . . . . . . . . . . . . . . . . . . .

62

- Picture Mode - Expert Control

. . . . . . . . . . . . . . . . . .

63

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 64

Advanced Control - Black (Darkness) Level

. . . . . . .

65

Advanced Control - Eye Care

. . . . . . . . . . . . . . . . . . . . . . . . . . .

66

Advanced Control - Real Cinema

. . . . . . . . . . . . . . . . . . . . . . 67

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Power Indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69

7

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 70

Preset Sound Settings (Sound Mode)

. . . . . . . . . . . . . . . 71

Sound Setting Adjustment - User Mode

. . . . . . . . . . .

72

Clear Voice

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Stereo/SAP Broadcast Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

On-Screen Menus Language Selection

. . . . . . . . . . . . . 79

Caption Mode

- Analog Broadcasting System Captions

. . . . . . .

80

- Digital Broadcasting System Captions

. . . . . . . .

81

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

83

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

85

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

PARENTAL CONTROL / RATINGS

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . .

88

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

92

Downloadable Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

97

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98

Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99

APPENDIX

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 3

Programming the Remote Control

. . . . . . . . . . . . . . . . . 10 4

IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

External Control Through RS-232C

. . . . . . . . . . . . . . . .10 9

Open Source License

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116

8

FEATURE OF THIS TV

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

FOR LCD TV

■

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is

nothing wrong with TV.

■

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.

■

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.

On Disposal (Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with
general household waste. Disposal of this product must be carried out in accordance to the regulations of your local
authority.

PREPARATION

9

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

OOppttiioonn EExxttrraass

* Wipe spots on the exterior only with

the polishing cloth.

* Do not wipe roughly when removing

stain. Excessive pressure may cause
scratch or discoloration.

Polishing Cloth

(This feature is not available

for all models.)

Copyright© 2007 LGE,
All Rights Reserved.

D-sub 15 pin Cable

1.5V 1.5V

Owner’s Manual Power Cord

Remote Control,

Batteries

INPUT

FAV

MUTE

T
V

S

T
B

POWER

Q. MENU

MENU

A
V

M

O
D

E

R
E
T

U
R

N

ENTER

V

O
L

C
H

123

456

78

0

9

FLASHBK

P
A
G

E

D

V

D

V

C
R

CD Manual

When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.

Bolts for stand assembly

(Refer to P.13)

(Only 32/37/42LG30DC)

Protection Cover

Screw for stand fixing

(Refer to P.16)

(Only 32/37/42LG30DC)

x 4 x 4

or

PREPARATION

10

PREPARATION

POWER Button

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using

PPoo wweerr IInnddiiccaa ttoorr

in

the OPTION menu.

GG

pp..6699

)

CHANNEL ( , )
Buttons

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

Intelligent Sensor (Except 32/37/42LG30DC)

Adjusts picture according to the surrounding
conditions

Remote Control Sensor

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

■

NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).

CH

VOL

ENTER

MENU

INPUT

PREPARATION

11

BACK PANEL INFORMATION

■

Image shown may differ from your TV.

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

RGB IN

COMPONENT IN

AUDIO

(RGB/DVI)

RGB(PC)

REMOTE

CONTROL IN

ANTENNA/

CABLE IN

1

2

RS-232C IN

(CONTROL & SERVICE)

VIDEO

AUDIO

OPTICAL COAXIAL

DIGITAL AUDIO OUT

AUDIO OUT

AV IN 1

R

HDMI/DVI IN

2

1

VIDEO

MONO

( )

AUDIO

S-VIDEO

1

3

4

6

7

8

2

9

9

5

RGB IN

COMPONENT IN

AUDIO

(RGB/DVI)

RGB(PC)

REMOTE
CONTROL IN

RJP

INTERFACE

ANTENNA/

CABLE IN

1

2

RS-232C IN

(CONTROL & SERVICE)

VIDEO

AUDIO

OPTICAL

AUDIO OUT

AV IN 1

R

VIDEO

MONO

( )

AUDIO

S-VIDEO

2

1

HDMI/DVI IN

DIGITAL

AUDIO OUT

1

3

4

7

6

2

8

5

10

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB

SERVICE ONLY

9

11

12

47/52LG50DC

32/37/42LG30DC

R

13

9

PREPARATION

12

PREPARATION

HDMI/DVI IN, HDMI IN

Digital Connection.
Supports HD video and Digital audio. Doesn’t

support 480i.
Accepts DVI video using an adapter or HDMI to

DVI cable (not included).

COMPONENT IN

Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red

and white for audio.

RGB (PC)

Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).

AUDIO (RGB/DVI)

1/8” headphone jack for analog PC audio input.

REMOTE CONTROL IN PORT

For a wired remote control.

RS-232C IN (CONTROL & SERVICE) PORT

Used by third party devices.

ANTENNA/CABLE IN

Connect over-the air signals to this jack.
Connect cable signals to this jack.

DIGITAL AUDIO OUT

Digital audio output for use with amps and home
theater systems.

Includes an optical and/or coaxial connection.
Note: In standby mode, these ports do not work.

AUDIO OUT

Analog audio output for use with amps and home
theater systems.

AV (Audio/Video) IN

Analog composite connection. Supports standard
definition video only (480i).

S-VIDEO

Better quality than standard composition.
Supports standard definition video only (480i).

USB INPUT

Used for viewing photos and listening to MP3s.

USB SERVICE ONLY

Used for software updates.

RJP INTERFACE

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

1

2

3

4

5

6

9

10

11

12

13

7

8

PREPARATION

13

STAND INSTRUCTION

■

Image shown may differ from your TV.

Assemble the parts of the

SS TT AANNDD BBOODDYY

with

CCOOVVEERR BBAASS EE

of the TV.

2

Assemble the TV as shown.

3

Fix the 4 bolts securely using the holes in the
back of the TV.

4

SS TT AANNDD BB OO DD YY

CCOOVVEERR BBAASS EE

Carefully place the TV screen side down on a cush­ioned surface to protect the screen from damage.

1

INSTALLATION (

Only 32/37/42LG30DC)

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Loose the bolts from TV.

2

Detach the stand from TV.

3

After removing the stand, install the included
pp rr ootteeccttiioo nn ccoo vveerr

over the hole for the stand.

Press the

PPRROOTTEECCTTIIOONN CC OOVVEERR

into the TV

until you hear it click.

PROTECTION COVER

GG

When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installa­tion). Do not over tighten.

NOTE

!

PREPARATION

14

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest dealer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

GG

Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric
shock.

CAUTION

GG

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

GG

Standard dimensions for wall mount kits are shown
in the table.

GG

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

GG

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to
the TV.

GG

For wall mounts that do not comply with the VESA

standard screw specifications, the length of the
screws may differ depending on their specifica­tions.

GG

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.

GG

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

AA

BB

Product Model

VESA

(A *B)

Standard Screw Quantity

32LG30DC

37LG30DC
42LG30DC
47LG50DC

52LG50DC

200* 10 0

200* 200

800* 400

M4

M6

M6

4

4

4

LCD TV

PREPARATION

15

CABLE MANAGEMENT

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as
shown.

Put the cables inside the CABLE MANAGE-

MENT CLIP and snap it closed.

CABLE MANAGEMENT CLIP

1

2

3

■

Image shown may differ from your TV.

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches
on all four sides from the wall.

■

Image shown may differ from your TV.

4 inches

4 inches

4 inches

4 inches

GG

Ensure adequate ventilation by following the
clearance recommendations.

GG

Do not mount near or above any type of
heat source.

CAUTION

SWIVEL STAND

After installing the TV, you can adjust the TV set
manually to the left or right direction by 20 degrees
to suit your viewing position.

PREPARATION

16

PREPARATION

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.

GG

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

Only 32/37/42LG30DC

GG

Screw: M5 x L

(*L: Table depth + 8~10 mm)

ex) Table depth: 15mm, Screw: M5 x 25

4-Screws
(not provided as parts of the product)

Stand

Desk

PREPARATION

17

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope or cord (sold separately) to tie the product. It is
safer to tie the rope so it becomes horizontal between the wall and the
product.

■

You should purchase necessary components to prevent TV from falling off of the stand.

■

Image shown may differ from your TV.

GG

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.

GG

To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

NOTE

!

PREPARATION

18

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.

For optimum picture quality, adjust the antenna direction if needed.

2. Cable

Wall
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire
when connecting the antenna.

Copper Wire

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA/

CABLE IN

R

ANTENNA/

CABLE IN

R

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

EXTERNAL EQUIPMENT SETUP

19

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.

Component Connection

1. How to connect

Connect the video outputs (Y, P

B, P

R

)

of the digital set-

top box to the

CC OO MMPP OO NNEENNTT II NN VV IIDDEEOO 11

jacks on

the TV. Match the jack colors (Y = green, P

B

= blue, and

P

R

= red).

Connect the audio output of the digital set-top box to
the

CC OO MMPP OO NNEENNTT IINN AAUUDDIIOO 11

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box. operation

)

■

Select the

CC oommppoo nneenntt 11

input source on the TV using

the

II NNPPUU TT

button on the remote control.

■

If connected to

CC OO MMPP OO NNEENN TT IINN22

input, select the

CC oommppoo nneenntt 22

input source on the TV.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

Y, C

B/

P

B, CR/

P

R

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

1920x1080p

Signal

480i

480p

720p

10 8 0 i

10 8 0 p

Component

Yes

Yes

Yes

Yes

Yes

HDMI

No

Yes

Yes

Yes

Yes

RGB IN

AUDIO

(RGB/DVI)

RGB(PC)

REMOTE

CONTROL IN

(CO

AV IN 1

COMPONENT IN

1

2

VIDEO

LYP

B

P

R

R

AUDIO

Y L RPB PR

1

2

EXTERNAL EQUIPMENT SETUP

20

EXTERNAL EQUIPMENT SETUP

HDMI Connection

Connect the digital set-top box to

HHDDMMII // DDVVII II NN11

or 22jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HHDDMMII11

or

HHDDMMII22

input source on the TV using

the

IINNPPUUTT

button on the remote control.

2

1

HDMI-DTV

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.939

67.50 60.00

Resolution

720x480p

1280x720p

1920x1080i

1920x1080p

RGB IN

COMPONENT

A

(RG

RGB(PC)

1

2

VIDEO

YP

B

P

R

HDMI/DVI IN

2

1

HDMI-DTV OUTPUT

1

EXTERNAL EQUIPMENT SETUP

21

DVI to HDMI Connection

1. How to connect

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s manu­al for the digital set-top box.

)

■

Select the

HHDDMMII11orHHDDMMII22

input source on the TV using

the

IINNPPUUTT

button on the remote control.

2

1

Connect the DVI output of the digital set-top box to
the

HHDDMMII//DDVVII IINN 11

or 22jack on the TV.

Connect the PC audio output to the

AAUU DD II OO

((

RRGGBB//DDVVII

))

jack on the TV.

GG

A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio
connection is necessary.

NOTE

!

RGB IN

COMPONENT IN

AUDIO

(RGB/DVI)

RGB(PC)

REMO

CONTRO

1

2

VIDEO

LYP

B PR R

AUDIO

HDMI/DVI IN

2

1

L R

DVI-DTV OUTPUT

1

2

EXTERNAL EQUIPMENT SETUP

22

EXTERNAL EQUIPMENT SETUP

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBP

R

Video output ports

on DVD player

Y

Y

Y

Y

P

B

B-Y

Cb

Pb

PR

R-Y

Cr

Pr

Connect the video outputs (Y, P

B, P

R

)

of the DVD to the

CC OO MM PPOO NNEENNTT IINN VVIIDDEEOO 11

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and PR

= red

)

.

Connect the audio outputs of the DVD to the
CC OO MM PPOO NNEENNTT IINN AAUUDDIIOO 11

jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

CC oommppoo nneenntt 11

input source on the TV using

the

II NNPPUU TT

button on the remote control.

■

If connected to

CC OO MMPP OO NNEENN TT IINN 22

input, select the

CC oommppoo nneenntt 22

input source on the TV.

■

Refer to the DVD player's manual for operating instructions.

2

1

RGB IN

AUDIO

(RGB/DVI)

RGB(PC)

REMOTE

CONTROL

(C

AV IN 1

COMPONENT IN

1

2

VIDEO

LYP

B

P

R

R

AUDIO

Y L RPB PR

1 2

EXTERNAL EQUIPMENT SETUP

23

HDMI Connection

Connect the HDMI output of the DVD to the
HHDDMMII//DDVVII II NN11

or 22jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HHDDMMII11

or

HHDDMMII22

input source on the TV using

the

II NNPPUU TT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

COMPONENT IN

AUDI

(RGB/D

RGB(PC)

1

2

VIDEO

LYP

B

P

R

A

HDMI/DVI IN

2

1

HDMI-DVD OUTPUT

1

S-Video Connection

GB/DVI)

REMOTE

CONTROL IN

ANTENNA/

CABLE IN

RS-232C IN

(CONTROL & SERVICE)

L R

AUDIO

OPTICAL COAXIAL

DIGITAL AUDIO OUT

AUDIO OUT

AV IN 1

VIDEO LR

(MONO)

AUDIO

S-VIDEO

L R

S-VIDEO

AUDIO

1

2

Connect the S-VIDEO output of the DVD to the
SS --VVIIDDEE OO

input on the TV.

Connect the audio outputs of the DVD to the

AAUUDDIIOO

input jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

AAVV11

input source on the TV using the

II NNPPUU TT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

EXTERNAL EQUIPMENT SETUP

24

VCR SETUP

EXTERNAL EQUIPMENT SETUP

Antenna Connection

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.
This phenomenon is common to all TVs and is not covered by warranty.

ANTENNA/

CABLE IN

COAXIAL

AUDIO OUT

(MONO)

AUDIO

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

1

2

Connect the RF antenna out socket of the
VCR to the

AANN TT EENN NNAA//CCAABBLLEE IINN

sock-

et on the TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

EXTERNAL EQUIPMENT SETUP

25

GG

Do not connect to both Video and S-Video at the same
time. In the event that you connect both Video and the
S-Video cables, only the S-Video will work.

CAUTION

GG

S-Video provides better quality
than composite. Use it when
available.

NOTE

!

S-Video Connection

AUDIO

(RGB/DVI)

REMOTE

CONTROL IN

ANTENNA

CABLE IN

RS-232C IN

(CONTROL & SERVICE)

L

R

AUDIO

OPTICAL COAXIAL

DIGITAL AUDIO OUT

AUDIO OUT

AV IN 1

VIDEO LR

(MONO)

AUDIO

S-VIDEO

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

1

2

Connect the S-VIDEO output of the VCR to the
SS --VVIIDDEE OO

input on the TV.

Connect the audio outputs of the VCR to the

AAUUDDIIOO

input jacks on the TV.

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR.
(

Refer to the VCR owner’s manual.

)

■

Select the

AAVV11

input source on the TV using the

II NNPPUU TT

button on the remote control.

2

1

Composite (RCA) Connection

GG

If you have a mono VCR, connect the audio cable from
the VCR to the

AAUUDDIIOO LL // MMOONNOO

jack of the TV.

NOTE

!

AUDIO

(RGB/DVI)

REMOTE

CONTROL IN

ANTENNA/

CABLE IN

RS-232C IN

(CONTROL & SERVICE)

L R

AUDIO

OPTICAL COAXIAL

DIGITAL AUDIO OUT

AUDIO OUT

AV IN 1

VIDEO L R

(MONO)

AUDIO

S-VIDEO

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

1

Connect the

AAUUDDIIOO/VVII DD EEOO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR.
(

Refer to the VCR owner’s manual.

)

■

Select the

AAVV11

input source on the TV using the

II NNPPUU TT

button on the remote control.

■

If connected to

AAVV IINN22

, select

AAVV22

input source on the TV.

1

EXTERNAL EQUIPMENT SETUP

26

PC SETUP

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

Connect the DVI output of the PC to the

HHDDMMII // DDVVII

II NN 11

or

22

jack on the TV.

Connect the PC audio output to the

AAUU DD II OO

((RRGG BB//DDVVII ))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

HHDDMMII11orHHDDMMII22

input source on the TV using the

II NNPPUU TT

button on the remote control.

2

1

COMPONENT IN

RE

CON

1

2

VIDEO

LYP

BPR

R

AUDIO

HDMI/DVI IN

2

1

RGB IN

AUDIO

(RGB/DVI)

RGB(PC)

DVI-PC OUTPUT

AUDIO

1 2

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

Connect the VGA output of the PC to the

RR GG BB

((

PPCC

))

jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO

((

RRGGBB//DDVVII

))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

RRGGBB--PP CC

input source on the TV using the

II NNPPUU TT

button on the remote control.

2

1

COMPONENT IN

REMOTE

CONTROL I

1

2

(CO

VIDEO

LYP

B

P

R

R

AUDIO

RGB IN

AUDIO

(RGB/DVI)

RGB(PC)

RGB OUTPUT

AUDIO

1 2

EXTERNAL EQUIPMENT SETUP

27

GG

32/37/42LG30DC: To get the the best picture
quality, adjust the PC graphics card to 1360x768.

GG

47/52LG50DC: To get the the best picture quali­ty, adjust the PC graphics card to 1920x1080.

GG

Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.

GG

In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or bright­ness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.

GG

Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could become
permanently imprinted on the screen.

GG

The synchronization input form for Horizontal and
Vertical frequencies is separate.

GG

Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.

GG

If there are overscan in HDMI-PC 1920x1080,
change aspect ratio to

JJuusstt ssccaa nn

.

NOTES

!

Supported Display Specifications (RGB-PC, HDMI-PC)

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.469 70.08

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.776 59.87

47.720 59.799

47.130 59.65

Resolution

720x400

1360x768

640x350

640x480

800x600

1024x768

1280x768

1366x768

For 32/37/42LG30DC

For 47/52LG50DC

* Only RGB-PC mode

Resolution

640x350

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.09

31.469 70.08

31.469 59.94

37.500 75.00

37.861 72.80

35.156 56.25

37.879 60.31

46.875 75.00

48.077 72.18

48.363 60.00

56.476 70.06

60.023 75.02

47.776 59.87

60.289 74.893

63.981 60.02

79.976 75.025

47.712 60.015

75.00 60.00

66.587 59.934

67.5 60.00

* Only RGB-PC mode

720x400

1360x768

640x480

800x600

1024x768

1280x1024

1600x1200

1920x1080

RGB-PC

HDMI-PC

1280x768

EXTERNAL EQUIPMENT SETUP

28

EXTERNAL EQUIPMENT SETUP

Screen Setup for PC mode

Selecting Resolution

You can choose the resolution in RGB-PC mode.
The

PP oossiittiioonn, PP hhaassee

, and

SS iizzee

can also be adjusted.

Select

PPIICCTTUURREE

.

Select

SS cc rreeeenn ((RRGG BB -- PPCC))

.

Select

RReessoo lluutt iioonn

.

Select the desired resolution.

1024 x 768

1280 x 768

1360 x 768

1366 x 768

Auto config.

Resolution

G

Position

Size

Phase

Reset

SCREEN

Move

Prev.

MENU

1

MENU

3

4

2

ENTER

ENTER

ENTER

5

ENTER

Enter

Move

PICTURE

E

• Contrast 50

• Brightness 50

• Sharpness 60

• Color 60

• Tint 0

• Advanced Control

• Reset

Screen (RGB-PC)

RG

Only for

32/37/42LG30DC

EXTERNAL EQUIPMENT SETUP

29

Auto Configure

Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.

Select

SS cc rreeeenn ((RRGG BB -- PPCC))

.

Select

AAuuttoo ccoonnff iigg..

.

Auto config.

G

Resolution

Position

Size

Phase

Reset

SCREEN

Move

Prev.

MENU

To Set

3

2

ENTER

ENTER

Select

YYeess

.

4

ENTER

Start Auto Configuration.

5

ENTER

Select

PPIICCTTUURREE

.

1

MENU

• If the position of the image is still not
correct, try Auto adjustment again.

• If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the

PPooss ii tt ii oonn, SS iizzee

or

PPhhaassee

.

Yes No

Enter

Move

PICTURE

E

• Contrast 50

• Brightness 50

• Sharpness 60

• Color 60

• Tint 0

• Advanced Control

• Reset

Screen (RGB-PC)

RG

EXTERNAL EQUIPMENT SETUP

30

EXTERNAL EQUIPMENT SETUP

Adjustment for screen Position, Size, and Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.

This feature operates only in RGB-PC mode.

Select

PPoossii ttiioonn, SS ii zzee

, or

PPhhaassee

.

Make appropriate adjustments.

Auto config.

Resolution

Position

G

Size

Phase

Reset

GF

D

E

SCREEN

Move

Prev.

MENU

3

ENTER

4

ENTER

■

PPoossii ttiioonn

: This function is to adjust pic­ture to left/right and up/down as you
prefer.

■

SS ii zzee

: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.

■

PPhhaa ssee

: This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.

Select

PPIICCTTUURREE

.

Select

SS cc rreeeenn ((RRGG BB -- PPCC))

.

1

MENU

2

ENTER

5

ENTER

Enter

Move

PICTURE

E

• Contrast 50

• Brightness 50

• Sharpness 60

• Color 60

• Tint 0

• Advanced Control

• Reset

Screen (RGB-PC)

RG