LG 50PQ60D, 50PS80FD, 42PQ60D Owner’s Manual

Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)

ID Number(s): 6422: 42PQ60D-GA 6493: 50PQ60D-GA 6492: 50PS80FD-GA 6767: 50PS30FD-GA 6766: 60PS80FD-GA

<![if ! IE]>

<![endif]>ENGLISH

PLASMA TV

OWNER’S MANUAL

42PQ6***

50PQ6***

50PS3*** 50PS8***

60PS8***

Please read this manual carefully before operating your TV.

Retain it for future reference.

Record the model number and serial number of the TV.

Refer to the label on the back cover and quote this information.

To your dealer when requiring any service.

HDMITM, the HDMI logo and HighDefinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.

■ Image shown may differ from your TV.

Owner’s Manual

Batteries

Remote Control

Cable management clip

(Refer to p.9) (Only 50/60PS8***)

<![if ! IE]>

<![endif]>ACCESSORIES

Power Cord	Protection cover
	(Refer to p.13)

This item is not included for all models.

Polishing Cloth Polishing cloth for use on the screen.

*Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth.

Do not use excessive force. This may cause scratching or discolouration.

Ferrite Core

(This item is not included for all models.)

Wall Mounting Bracket

(Separate purchase)

AW-50PG60MS	AW-60PG60MS
(Except for 60PS8***)	(Only 60PS8***)

Use of ferrite core (This item is not included for all models.)

Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord. The closer the location of the ferrite core to the power

plug, the better it is.

plug closely.

1

CONTENTS

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

	PREPARATION
<![if ! IE]> <![endif]>CONTENTS	Back Cover for Wire Arrangement ............................	9
	Front Panel Controls.....................................................	4
	Back Panel Information ................................................	6
	Stand Installation...........................................................	8
	Careful installation advice .....................................	10
	Swivel Stand ...................................................................	11
	Desktop Pedestal Installation................................	11
	Wall Mount: Horizontal Installation........................	12
	Not Using the desk-type stand.................................	13
	Antenna Connection...................................................	14
	EXTERNAL EQUIPMENT SETUP
	HD Receiver Setup ......................................................	15
	DVD Setup.....................................................................	18
	VCR Setup.....................................................................	20
	AV Output Setup ........................................................	22
	Digital Audio Out Setup............................................	23
	Other A/V Source Setup...........................................	24
	Usb Setup......................................................................	25
	PC Setup........................................................................	26
	- Screen Setup for PC Mode ...............................	30
	WATCHING TV / PROGRAMME CONTROL
	Remote Control Key Functions ...............................	34
	Turning on the TV.......................................................	36
	Programme Selection ................................................	36
	Volume Adjustment ...................................................	36
	Quick Menu .................................................................	37
	On-Screen Menus Selection and Adjustment.....	38
	Auto Programme Tuning............................................	39
	Manual Programme Tuning (In Digital Mode).....	40
	Manual Programme Tuning (In Analogue Mode) ...	41
	Programme Edit ...........................................................	43
	Software Update..........................................................	45
	Diagnostics ...................................................................	46
	Selecting the Programme List ..................................	47

Favourite Programme Setup......................................	48
Input List........................................................................	49
Input Label ....................................................................	50
Simple manual...............................................................	51
.................................................................	52
AV Mode........................................................................	55
Initializing (Reset to original factory settings) .....	56
TO USE A USB DEVICE
When connecting the a USB device ......................	57
Photo List ......................................................................	58
Music List........................................................................	62
Movie List .......................................................................	65
DivX Registration Code..............................................	69
Deactivation...................................................................	70
EPG (ELECTRONIC PROGRAMME
GUIDE) (IN DIGITAL MODE)
Switch on/off EPG ......................................................	71
Select a Programme....................................................	71
Button Function in NOW/NEXT Guide Mode .......	71
Button Function in 8 Day Guide Mode..................	72
Button Function in Date Change Mode................	72
Button Function in Extended Description Box.........	73
Button Function in Remind Setting Mode.........................	73
Button Function in Schedule List Mode................	73

MHEG (MULTIMEDIA AND HYPERMEDIA INFORMATION CODING EXPERT GROUP) (IN DIGITAL MODE)

Switch on MHEG .........................................................	74
Select a Programme....................................................	74
Button Function in NOW/NEXT Guide Mode ......	75
Button Function in Listing Mode ..............................	75

2

PICTURE CONTROL
Picture Size (Aspect Ratio) Control.......................	76
Picture Wizard................................................................	78
Energy Saving ................................................................	79
Preset Picture Settings
- Picture Mode-Preset............................................	80
Manual Picture Adjustment
- Picture Mode-User option.................................	81
Picture Improvement Technology...........................	82
Expert Picture Control...............................................	83
Picture Reset.................................................................	86
Image Sticking Minimization (ISM) Method .........	87
Demo Mode..................................................................	88
Mode Setting.................................................................	89

PARENTAL CONTROL / RATINGS
Set Password & Lock System.................................	103
Block Programme ......................................................	104
Parental Control (In Digital Mode only).............	105
External Input Blocking.............................................	106
Key Lock ......................................................................	107
TELETEXT
Switch on/off .............................................................	108
SIMPLE Text................................................................	108
TOP Text......................................................................	108
FASTEXT......................................................................	109
Special Teletext Functions ......................................	109

<![if ! IE]>

<![endif]>CONTENTS

SOUND & LANGUAGE CONTROL
Auto Volume Leveler...................................................	90
Clear Voice II..................................................................	91
Preset Sound Settings - Sound Mode...................	92
Sound Setting Adjustment -User Mode.................	93
SRS TruSurround XT ..................................................	93
Balance...........................................................................	94
TV Speakers On/ Off Setup......................................	95
Selecting Digital Audio Out ......................................	96
Audio Reset....................................................................	97
Stereo Reception (In Analogue Mode Only) ............	98
Speaker Sound Output Selection ..........................	98
Language Selection (In Digital Mode only).........	99

TIME SETTING
Clock Setup................................................................	100
Auto On/ Off Time Setting ....................................	101
Sleep Timer Setting ..................................................	102

APPENDIX
Troubleshooting .........................................................	110
Maintenance ...............................................................	112
Product Specifications..............................................	113
IR Codes.......................................................................	114
External Control Device Setup...............................	116
Open Source Software Notice...............................	123
Open Source License ...............................................	124

3

PREPARATION

<![if ! IE]>

<![endif]>PREPARATION

FRONT PANEL CONTROLS

■ Image shown may differ from your TV.

CAUTION

G When the TV cannot be turned on with the remote control, press the main power button on the TV. (When the power is turned off with the main power button on the TV, it will not be turned on with the remote control).

G Do not step on the glass stand or subject it to any impact.

It may break, causing possible injury from fragments of glass, or the TV may fall.

drag the TV. damaged.

42/50PQ6***

Remote Control	Intelligent Sensor
Sensor	Adjusts	picture accord-
	ing to	the surrounding
	conditions

Power/Standby Indicator

•Illuminates red in standby mode.

•The LED is off while the TV remains on.

P PROGRAMME

P

VOLUME

OK

OK

MENU

MENU

INPUT

INPUT

POWER

4

50/60PS8***

Intelligent Sensor Adjusts picture according to the surrounding conditions.

Remote Control

Sensor

Power/Standby

• Illuminates red standby mode.

• The LED is off while the TV remains on

P PROGRAMME

P

VOLUME

OK

OK

MENU MENU INPUT INPUT

POWER

50PS3***

Remote Control

Sensor

Intelligent Sensor

Adjusts picture according to the surrounding conditions.

Power/Standby Indicator

• Illuminates red in standby mode.

• Illuminates blue when the TV is switched on.

	INPUT	MENU		OK		P
INPUT	INPUT	OK	MENU	OK	VOLUME	PROGRAMME	POWER
	MENU				P

<![if ! IE]>

<![endif]>PREPARATION

5

PREPARATION

BACK PANEL INFORMATION

A Image shown may differ from your TV.

Only 42/50PQ6***, 50PS3***

<![if ! IE]> <![endif]>PREPARATION
1
2	3

2

1

AV

VIDED

)

O L(M - IO D U A - R

4

5

6

AUDIO IN (RGB/DVI)

R-AUDIO-LVIDEO

<![if ! IE]>

<![endif]>COMPONENT IN

<![if ! IE]>

<![endif]>VARIABLE AUDIO OUT

10

1

7

<![if ! IE]>

<![endif]>3

<![if ! IE]>

<![endif]>VIDEO L/MONO AUDIO R

AV IN 2

11

7

This TV operates on an AC power. The voltage is indicated on the Specifications page.

attempt to operate the TV on DC power.

2

Connect digital audio to various types of equipment. Use to connect to a Digital Audio Compo nt. Use an Optical audio cable.

3RGB/DVI Audio Input

Connect the audio from a PC or DTV.

4HDMI Input

Connect a HDMI signal to HDMI IN or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable

5RGB IN Input

Connect the output from a PC.

6RS-232C IN (CONTROL & SERVICE) PORT

6Connect to the RS-232C port on a PC.

Connect audio/video output from an external device to these jacks.

8AV Output

Connect second TV or monitor to the AV OUT socket on the TV.

9Component Input

Connect a component video/audio device to these jacks.

10Antenna Input

Connect RF antenna to this jack.

11USB Input

Connect USB storage device to this jack.

This port is used for Service or Hotel mode.

Only 50/60PS8***

1

2

3

3

2

1

AUDIO IN (RGB/DVI)

-AUDIO-L

<![if ! IE]>

<![endif]>COMPONENT IN

4	5	6			9
			7
1					7

<![if ! IE]>

<![endif]>4

<![if ! IE]>

<![endif]>VIDEO L/MONO AUDIO R

AV IN 2

11

7

This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.

2

Connect digital audio to various types of equipment. Use to connect to a Digital Audio Component. Use an Optical audio cable.

3RGB/DVI Audio Input

Connect the audio from a PC or DTV.

4HDMI Input

Connect a HDMI signal to HDMI IN or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.

RGB IN Input

Connect the output from a PC.

Connect audio/video output from an external device to these jacks.

AV Output

Connect second TV or monitor to the AV OUT socket on the TV.

Component Input

Connect a component video/audio device to these jacks.

Antenna Input

Connect RF antenna to this jack.

USB Input

Connect USB storage device to this jack.

6

Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode.

<![if ! IE]>

<![endif]>PREPARATION

7

PREPARATION

<![if ! IE]>

<![endif]>PREPARATION

STAND INSTALLATION (Except for 60PS8***)

■ Image shown may differ from your TV

When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt.

Only 42/50PQ6***, 50PS3***		Only 50PS8***
1	Carefully place the TV screen side down on a cushioned	1 Carefully place the TV screen side down on a cushioned
	surface to protect the screen from damage.	surface to protect the screen from damage.

2 Assemble the TV as shown.

2 Assemble the TV as shown.

3 Fix the 4 bolts securely using the holes in the back of the TV.

3	Fix the 4 bolts securely using the holes in the
	back of the TV.

! NOTE

G When assembling the stand, make sure to distinguish and assemble the front and rear side of the stand correctly.

FRONT		FRONT

8

BACK COVER FOR WIRE ARRANGEMENT

■ Image shown may differ from your TV.

After Connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables.

<![if ! IE]>

<![endif]>PREPARATION

		CABLE HOLDER
	Only 50/60PS8***
	1	install	2
		the cables.
		To connect additional equipment, see the
		External equipment Setup section.

	CABLE HOLDER	CABLE MANAGEMENT CLIP
How to remove the cable management clip
Hold the CABLE MANAG	both hands and pull it upward.

! NOTE

G Do not use the CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.	9

PREPARATION

CAREFUL INSTALLATION ADVICE

A You should purchase necessary components to fix the TV safety and secure to the wall from a hardware supplier.

A Position the TV close to the wall to avoid the possibility of it falling when pushed.

		A
		The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoiding the possibility
	<![if ! IE]> <![endif]>PREPARATION	of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also pre-
		vent the TV from damage. Ensure that children do not climb or hang from the TV.
		1	1
		2	2

1Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

2Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

3

3Use a sturdy rope or wire to tie the product for alignment. It is safer to tie the rope so it becomes horizontal between the wall and the product.

! NOTE

GWhen moving the TV undo the cords first.

GUse a platform or cabinet strong and large enough to support the size and weight of the TV.

GTo use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

10

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

<![if ! IE]>

<![endif]>PREPARATION

AThe TV can be installed in various ways such as on a wall, or on a desktop etc.

AThe TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker

DESKTOP PEDESTAL INSTALLATION

For adequate ventilation allow a clearance of 4” (10cm) all around the TV.

4 inches

4 inches

4 inches

4 inches

11

PREPARATION

<![if ! IE]>

<![endif]>PREPARATION

WALL MOUNT: HORIZONTAL INSTALLATION

AWe recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.

AWe recommend that you purchase a wall mounting bracket which supports VESA standard.

ALG recommends that wall mounting be performed by a qualified professional installer.

	4 inches	Model	VESA	Standard	Quantity
			(A * B)	Screw
		4 inches	400 * 400	M6	4
	4 inches	42PQ6***
		4 inches	400 * 400	M6	4
		50PQ6***
		50PS3***	400 * 400	M6	4
	4 inches	50PS8***	400 * 400	M6	4
		60PS8***	600 * 400	M8	4

A

B

! NOTE

GShould Install wall mount on a solid wall perpendicular to the floor.

GShould use a special wall mount, if you want to install it to ceiling or slanted wall.

GThe surface that wall mount is to be mounted on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.

GInstalling screw type and length depends on the wall mount used. Further information, refer to the instructions included with the mount.

GLG is not liable for any accidents or damage to property or TV due to incorrect installation:

-Where a non-compliant VESA wall mount is used.

-Incorrect fastening of screws to surface which may cause TV to fall and cause personal injury.

-Not following the recommended Installation method.

12

NOT USING THE DESK-TYPE STAND

■ Image shown may differ from

When installing the wall-

<![if ! IE]>

<![endif]>PREPARATION

PROTECTION COVER

Insert the PROTECTION COVER into the TV until clicking sound.

13

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

PREPARATION

■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.

ANTENNA CONNECTION

■ For optimum picture quality, adjust antenna direction.

■ An antenna cable and converter are not supplied.

	Wall	Multi-family Dwellings/Apartments
		(Connect to wall antenna socket)
	Antenna
	Socket

RF Coaxial Wire (75 ohm)

Outdoor

Antenna

(VHF, UHF) Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

	UHF
Antenna	Signal
	Amplifier
	VHF

■In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above.

■If signal needs to be split for two TVs, use an antenna signal splitter for connection.

14

EXTERNAL EQUIPMENT SETUP

■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.

■This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50PQ6*** models.

■Image shown may differ from your TV.

HD RECEIVER SETUP

■This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.

Connecting with a component cables

1

Connect the video outputs (Y, PB, PR) of the digital set top box to the COMPONENT IN VIDEO jacks on the TV.

the digital set-top box to the COMPONENT IN AUDIO jacks on the TV.

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

Select Component 1 input source using the INPUT button on the remote control.

If connected to COMPONENT IN 2 input, select Component 2 input source.

Signal	Component	HDMI
480i/576i	O	X
480p/576p	O	O
720p/1080i	O	O
1080p	O	O
	(50Hz/60Hz only)	(24Hz/30Hz/50Hz/60Hz)

1

2

<![if ! IE]>

<![endif]>COMPONENT IN

1 2

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

15

EXTERNAL EQUIPMENT SETUP

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

Connecting a set-top box with an HDMI cable

1	Connect the digital set-top box to HDMI/DVI IN 1,	42/50PQ6***, 50PS3***
	HDMI IN 2, HDMI IN 3 or HDMI IN 4(Only
	50/60PS8***) jack on the TV.

top box.	2
Refer to the owner’s manual for the digital set-top box.)	1
Select HDMI1, HDMI2, HDMI or HDMI IN 4(Only
50/60PS8***) input source using the INPUT button

on the remote control.

! NOTE	1
G Check that your HDMI cable is version 1.3 or higher.
If the HDMI cables don’t support HDMI version 1.3, flicker
ing or no screen display can result. Please use the latest
cables that support at least HDMI version 1.3.

50/60PS8***

3

2

1

1

16

Connecting with an HDMI to DVI cable

1Connect the digital set-top box to HDMI/DVI IN 1 jack on the TV.

output of the digital set-top box to /DVI) jack on the TV.

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

Select HDMI1 input source using the INPUT button on the remote control.

42/50PQ6***, 50PS3***

2

AV

1 VIDEO

L(MONO) - AUDIO - R

IN1

AUDIO IN (RGB/DVI)

R-AUDIO-LVIDEO

OUT 1

2

50/60PS8***

3

2

AV

1 VIDEO

L(MONO) - AUDIO - R

IN1

AUDIO IN (RGB/DVI)

R-AUDIO-LVIDEO

OUT 1

1

2

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

17

EXTERNAL EQUIPMENT SETUP

DVD SETUP

Connecting with a component cables

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

1Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV.

audio outputs of the DVD to the	1
NT IN AUDIO jacks on the TV.
Turn on the DVD player, insert a DVD.

Select Component 1 input source using the INPUT button on the remote control.

If connected to COMPONENT IN 2 input, select Component 2 input source.

Refer to the DVD player's manual for operating instructions.

2

1 2

<![if ! IE]>

<![endif]>COMPONENT IN

Component Input ports

To achieve better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV	Y	PB	PR
	Y	PB	PR
Video output ports	Y	B-Y	R-Y
on DVD player	Y	Cb	Cr
	Y	Pb	Pr

18

Connecting the HDMI cable

Connect the HDMI output of the DVD to the

1HDMI/DVI IN 1, HDMI IN 2, HDMI IN 3 or HDMI IN 4(Only 50/60PS8***) jack on the TV.

I1, HDMI2, HDMI3 or HDMI4(Only input source using the INPUT button on

the remote control.

Refer to the DVD player's manual for operating instructions.

! NOTE

G The TV can receive video and audio signals simultaneously when using a HDMI cable.

G If the DVD does not support Auto HDMI, you must set the output resolution appropriately.

G Check that your HDMI cable is version 1.3 or higher.

If the HDMI cables don’t support HDMI version 1.3, flickering or no screen display can result. Please use the latest cables that support at least HDMI version 1.3.

42/50PQ6***, 50PS3***

2

1

1

50/60PS8***

3

2

1

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

1

19

EXTERNAL EQUIPMENT SETUP

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

VCR SETUP

■ To avoid picture noise (interference), allow adequate distance between the VCR and TV.

Connecting with a RF Cable
<![if ! IE]> <![endif]>IN
<![if ! IE]> <![endif]>COMPONENT
L
-
AUDIO
-
R
IN1 OUT 1 2	ANT OUT S-VIDEO VIDEO L R
	1
	OUTPUT
	SWITCH

Wall Jack

2

Antenna

1Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.

the antenna cable to the ANT IN socket of the VCR.

Press the PLAY button on the VCR and match the appropriate channel between the TV and VCR for viewing.

20

Connecting with an RCA cable

1	the AUDIO/VIDEO jacks between TV and
	Match the jack colours (Video = yellow, Audio Left
	= white, and Audio Right = red)
2	Insert a video tape into the VCR and press PLAY on
	the VCR. (Refer to the VCR owner’s manual.)
				1
3	Select AV2 input source using the INPUT button on
	the remote control.		2
	If connected to AV IN 1 input, select	AV1 input
	source.
! NOTE
			S-VIDEO	VIDEO L	R ANT IN
G If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO jack of the TV.				OUTPUT	ANT OUT
				SWITCH

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

21

EXTERNAL EQUIPMENT SETUP

AV OUTPUT SETUP

The TV has a special signal output capability which allows you

to hook up the second TV or monitor.

	1		Connect the seco
			jacks.
<![if ! IE]> <![endif]>EXTERNAL			See the Operati
<![if ! IE]> <![endif]>EQUIPMENT
			out. Component, RGB, HDMI input sources cannot be used
			NOTE
		G Only Digital, Analogue, AV1, AV2 mode can be used for AV
<![if ! IE]> <![endif]>SETUP			for AV out.
		G We recommend to use the AV OUT jacks for VCR recording.

AUDIO IN (RGB/DVI)

			<![if ! IE]> <![endif]>IN
	AV		<![if ! IE]> <![endif]>PONENT
	D
	VIDE	VIDEO
	L(MONO)
		-	1
	-
	AUDIO	AUDIO
	-	-
	R	R
	IN1	OUT
		1	2

VIDEO	L	R

22

DIGITAL AUDIO OUT SETUP

Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.

If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL

AUDIO OUT terminal on the back of TV to a DVD Home Theater (or amp).

1Connect one end of an optical cable to the TV Digital

Audio (Optical) Output port.

optical cable to the the audio equipment.

menu.(Gp.95). Refer to the external audio equipment instruction manual for operation.

CAUTION

GDo not look into the optical output port. Looking at the laser beam may damage your vision.

! NOTE

G When connecting with external audio equipments, such as amplifiers or speackers, please turn the TV speakers off.

AUDIO IN (RGB/DVI)

		AV
		VIDED
		)
		O
		N
	1	O
		L(M
		-
		IO
		D
		U
		A
		-
		R

IN1

	<![if ! IE]> <![endif]>VIDEO
	<![if ! IE]> <![endif]>R-AUDIO-L
OUT	1	2

2

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

23

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

<![if ! IE]> <![endif]>EXTERNAL
<![if ! IE]> <![endif]>SETUPEQUIPMENT	3

1

2

Camcorder

Video Game Set

VIDEO L R

	1	between TV and external equipment. Match the jack colours .
		(Video = yellow, Audio Left = white, and Audio Right = red)

2Select AV2 input source with using the INPUT button on the remote control. If connected to AV IN 1 input, select AV1 input source.

3Operate the corresponding external equipment. Refer to external equipment operating guide.

24

USB SETUP

1Connect the USB device to the USB IN jack on the TV.

SB IN jacks, you use the

1

3

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

25

EXTERNAL EQUIPMENT SETUP

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

Connecting with a D-sub 15 pin cable

AUDIO IN (RGB/DVI)

1Connect the RGB output of the PC to the RGB IN (PC) jack on the TV.

audio output to the AUDIO IN n the TV.

Turn on the PC and the TV.

Select RGB input source using the INPUT button on the remote control.

AV

VIDEO
L(MONO)		AUDIO
-
AUDIO		-
-		R
R
IN1	OUT	1	2

RGB OUTPUT

AUDIO

26

Connecting with an HDMI to DVI cable

1Connect the DVI output of the PC to the HDMI/DVI IN1 jack on the TV.

outputCOMPONENTIN to the AUDIO IN the TV.

Turn on the PC and the TV.

Select HDMI1 input source using the INPUT button on the remote control.

42/50PQ6***, 50PS3***

2

AV

1 VIDEO

L(MONO) - AUDIO - R

IN1

AUDIO IN (RGB/DVI)

R-AUDIO-LVIDEO

OUT 1

2

50/60PS8***

3

2

AV

1 VIDEO

L(MONO) - AUDIO - R

IN1

AUDIO IN (RGB/DVI)

R-AUDIO-LVIDEO

OUT 1

1

2

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

27

EXTERNAL EQUIPMENT SETUP

<![if ! IE]>

<![endif]>SETUP EQUIPMENT EXTERNAL

Supported Display Resolution

RGB-PC, HDMI/DVI-PC mode				HDMI/DVI-DTV mode
Resolution	Horizontal	Vertical		Resolution	Horizontal	Vertical
	Frequency(kHz)	Frequency(Hz)			Frequency(kHz)	Frequency(Hz)
					31.649	59.94
720x400	31.468	70.08		640x480
640x480	31.469	59.94			31.469	60
800x600	37.879	60.31		720x480	31.47	59.94
1024x768	48.363	60.00			31.50	60
1280x768	47.78	59.87		720x576	31.25	50.00
1360x768	47.72	59.80		1280x720	37.50	50.00
1280x1024	63.98	60.02			44.96	59.94
(Except for 42/50PQ6***)					45.00	60
1400x1050	65.317	59.979		1920x1080	28.125	50.00
(Except for 42/50PQ6***)					33.72	59.94
1920x1080	66.587	59.934			33.75	60
					27.00	24.00
					33.750	30
					56.25	50.00
					67.433	59.94
					67.50	60

28