LG 50pc5d Diagram

PLASMA TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS :PA-73E

MODEL : 50PC5DC 50PC5DC-UC

MODEL : 50PC5D 50PC5D-UC

CANADA : http//biz.lgservice.com
USA : http//www.lgservice.com

: http//biz.lgservice.com

- 2 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance

An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.

It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the same specified type.

When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.

Leakage Current Hot Check circuit

CANADA: LG Electronics Canada, Inc. 550 Matheson

Boulevard East Mississauga, Ontario L4Z 4G3

USA : LG Customer Interactive Center

P.O.Box 240007, 201 James Record Road Huntsville,
AL 35824
Digital TV Hotline [phone]

1.5 Kohm/10W

To Instrument's
exposed
METALLIC PARTS

Good Earth Ground
such as WATER PIPE,
CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 3 -

DESCRIPTION OF CONTROLS...........................................4

SPECIFICATIONS.................................................................8

ADJUSTMENT INSTRUCTIONS ..........................................9

TROUBLESHOOTING GUIDE............................................19

PRINTED CIRCUIT BOARDS.............................................24

BLOCK DIAGRAM...............................................................27

EXPLODED VIEW...............................................................32

EXPLODED VIEW PARTS LIST .........................................33

REPLACEMENT PARTS LIST............................................34

SCHEMATIC DIAGRAM..........................................................

TABLE OF CONTENTS

- 4 -

FRONT PANEL INFORMATION

Here shown may be somewhat different from your TV.

Front Panel Controls

Power Standby Indicator
Illuminates red in standby mode.

When the TV is turned on, the indica­tor blinks green and then illuminates
green before the picture is displayed.

Remote Control Sensor

POWE
R
Button

INPUT
Button

MENU
Button

ENTER
Button

VOLUME
(

F,G

)Buttons

CHANNEL
(

E,D

)Buttons

Plasma TV Model

DESCRIPTION OF CONTROLS

INPUT

MENU

ENTER

VOL

CH

- 5 -

BACK PANEL INFORMATION

Back Connection Panel

AV IN 2

L/MONO

R

AUDIO

VIDEO

S-VIDEO

S-VIDEO Input
Provides better picture quality than the video

input.
AUDIO Input
VIDEO Input

Connects the video signal from a video device.

R

HDMI IN

HDMI/DVI IN

VIDEO

AUDIO

VIDEO

AUDIO

MONO

( )

S-VIDEO

ANTENNA/

CABLE IN

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN

(RGB/DVI)

DIGITAL AUDIO

OUT

OPTICAL

1

2

SERVICE

COMPONENT IN

AV OUT

AV IN 1

2

1

8

3

7

6

9

5

Plasma TV Model

4

11

10

DESCRIPTION OF CONTROLS

- 6 -

REMOTE CONTROL FUNCTIONS

1 2 3

4 5 6

7809

BACK

VOL CH

MUTE

FAV

BRIGHT -

MENU

BRIGHT +

ENTER

EXIT

TIMER

RATIO

SIMPLINK

POWER

V

C

R

TV

DVD

A

U

D

IO

CABLE

STB

MODE

TV INPUT

INPUT

When using the remote control, aim it at the remote control sensor on the TV.

MODE

MENU

BRIGHT -/ +

THUMBSTICK

(Up/Down/Left
Right/ENTER)

EXIT

TIMER

RATIO

SIMPLINK

VOLUME UP

/DOWN

MUTE

FAV

CHANNEL
UP/DOWN

— (DASH)

BACK

Select the remote’s operating mode. Defaults to LG
codes, refer to page 70 to reprogram.

Control video cassette recorders or DVD players.

Displays the main menu.

Adjust the brightness on screen.

Navigate the on-screen menus and adjust the sys­tem settings to your preference.

Clear all on-screen displays and return to TV view­ing from any menu.

Select the amount of time before your TV turns off
automatically.

Change the aspect ratio.

C?

Increase/decrease the sound level.

Switch the sound on or off.

Scroll through the programmed Favorite channels.

Select available channels.

Used to enter a program number for multiple pro­gram channels such as 2-1, 2-2, etc.

Tune to the last channel viewed.

VCR/DVD

control buttons

NUMBER but-

ton

Illuminates the remote control
buttons of selected mode.

LIGHT

DESCRIPTION OF CONTROLS

- 7 -

ADJUST

SAP

SOUND

PICTURE

CC

1 2 3

4 5 6

7809

BACK

POWER

TV INPUT

INPUT

Turns your TV or any other programmed equipment on or off, depending on the mode.

In AV 1-2, Component 1-2, RGB-PC, HDMI1/DVI, and HDMI2 input sources, screen
returns to the last TV channel.

External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC,
HDMI1/DVI and HDMI2.

(AV 1-2, Component 1-2, RGB-PC, HDMI1/DVI, and HDMI2 input sources are linked
automatically, only if a device is connected.)

PICTURE

SOUND

SAP

CC

ADJUST

Selects the factory preset picture depend
on the viewing environment.

Selects the factory preset sound for type of
program.

Analog mode: Selects MTS sound (Mono,
Stereo, or a SAP)

DTV mode: Changes the audio language.

Select a closed caption.
(*In DTV/CADTV mode )

Adjust the screen resolution, position, size
and phase.

Inside the Sliding Cover

DESCRIPTION OF CONTROLS

- 8 -

The specifications shown above may be changed without prior notice for quality improvement.

42PC5D

(42PC5D-UC)

50PC5D

(50PC5D-UC)

MODELS

41.3 x 30.2 x 12.2 inches

1048.0 x 766.0 x 310.0 mm

41.3 x 28.1 x 3.3 inches

1048.0 x 713.0 x 83.5 mm

60.8 pounds / 27.6 kg

53.4 pounds / 24.2 kg

48.9 x 34.9 x 14.6 inches

1242.0 x 887.6 x 370.0 mm

48.9 x 32.6 x 3.5 inches

1242.0 x 827.2 x 88.0 mm

86.6 pounds / 39.3 kg

76.3 pounds / 34.6 kg

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 104°F (0 ~ 40°C)

Less than 80%

-4 ~ 140°F (-20 ~ 60°C)
Less than 85%

Dimensions
(Width x Height x Depth)

Weight

Power requirement
Television System
Program Coverage
External Antenna

Impedance

Environment condition

Including stand

Excluding stand

including stand
excluding stand

Operating
Temperature

Operating Humidity

Storage Temperature
Storage Humidity

SPECIFICATIONS

- 9 -

ADJUSTMENT INSTRUCTIONS

1. Application Object

These instructions are applied to all of the PDP TV, PA73E.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test equipment.
(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if

there is no specific designation.
(4) The input voltage of the receiver be must kept 110V, 60Hz

when adjusting.
(5) The receiver must be operational for about 15 minutes

prior to the adjustments.

O Preliminary action is applied to the test for afterimage

discharge detection, and 100% FULL WHITE PATTERN
must be operated automatically.

1) Pressing Power On key

2) Full Test Pattern(2 min 30sec)

3) Full Black Pattern(30sec)

4)Full White Pattern

O

Pattern Mode is deselected by pressing CH +/-, Exit Key.

[ Set is activated HEAT-RUN without signal generator in this

mode.

3. MICOM Download(Option)

3-1. Required Test Equipment

(1) JIG-LEVER TYPE for adjusting: 1EA
(2) PC & MONITOR: 2EA
(3) BOARD for INTERFACE: IIC & ISP BOARD: 2EA
(4) 15P D-SUB CABLE: 2EA
(5) Using the 12/15 line of D-SUB 15P

12-SDA/15-SCL

3-2. JIG Connection

3-3. Establishment Program

(1) Establish LGE Monitor Tools v1.1
(2) The program work and it is opened program window as

seen below.

Test Pattern 2min 30sec

Test Pattern 30sec

If you turn on a still screen more than 20 minutes (Especially
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage
may occur in the black level part of the screen.

connection

to PC

connection

to PC

- 10 -

ADJUSTMENT INSTRUCTIONS

(3) Click the first icon shown in fig.9. The window seen in

fig.10 should appear.

3-4. Set Method

(1) MCU Select: MTV512M64
(2) Option

R/W Option: Auto Write(Verity)

Jig Option: Myson

Transmit Speed: Medium

(3) Check: Just do it with blank micom.
(4) PORT

Chose Parallel Port (normal LPT1)

Attention: You must chose EPP when select Rom BIAS at

LPT

3-5. Download Method

(1) Click the Load File.

(2) Locate and select the correct file from your computer.

(*.hex).

(3) Click the Send.

(4) When you see (ISP COMPLETE) the download is

complete.

- 11 -

ADJUSTMENT INSTRUCTIONS

4. USB S/W Download (Option)

4-1. Overview

USB Download enables quick response to S/W upgrading and
helps to configure the panel to the latest updates.

4-2. How to Download

(1) Before starting USB download, ensure that the power is

turned off and the display is turned on.
(2) Once the USB memory stick containing the upgraded file

is connected to the USB port on the main board, the

following picture appears on the screen.

(3) Check the current version at [Current TV Software Version

Information] and the target version at [New Found TV

Software Version Information]. Press Enter on the remote

controller to confirm the upgrade.
(4) The following picture shows the downloading in progress.

Once the download is completed, the power is

automatically turned on and off. (Otherwise, please turn the

power on and off)

(5) Once the download is completed, remove the USB

memory stick from the USB port. Press IN-START on the
remote controller to check the upgraded S/W version at the
top of the screen while the display is turned on.

Do not plug off.
Press EXIT to cancel the upgrade.

<S/W Upgrade Screen>

The software upgrade is now in progress.
Until the whole process if completed, please.

- Do not remove the memory card from the slot.

- Do not plug off.

Reading the file---Done
Upgrading---Done

The TV will restart automatically in 0 seconds.

<Downloading in progress Screen>

- 12 -

ADJUSTMENT INSTRUCTIONS

5. POWER PCB Assy Voltage
Adjustment

(Va, Vs Voltage Adjustment)

5-1. Test Equipment : D.M.M 1EA
5-2. Connection Diagram for Measuring

Refer to Fig 1.

5-3. Adjustment(42”/50”)

(1) Va Adjustment

1) Connect + terminal of D.M.M to Va pin of P812(50”:
P805) and connect – terminal to GND pin of P812(50”:
P805).

2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

(2) Vs Adjustment

1) Connect + terminal of D.M.M to Vs pin of P812(50”:
P805) and connect – terminal to GND pin of P812(50”:
P805).

2) Adjust VR951 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

5-4. Adjustment(Sanken: EAY32929001)

(1) Va Adjustment

1) Connect + terminal of D.M.M to Va pin of P12 and
connect – terminal to GND pin of P12.

2) Adjust VR951 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

(2) Vs Adjustment

1) Connect + terminal of D.M.M to Vs pin of P12 and
connect – terminal to GND pin of P12.

2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

Each PCB Assy must be checked by Check JIG Set before
assembly. (Especially, be careful Power PCB Assy which can
cause Damage to the PDP Module.)

111

VsAD J

VR951

VaADJ

VR901

3.3VADJ

VR22 1

T8
01

T9
01

T1
12

T5
01

L6
01

5V

GND

Va

GND

GND

NC

Vs

Vs

P811

111

VsAD J

VR951

VsAD J

VR951

VaADJ

VR901

VaADJ

VR901

3.3VADJ

VR22 1

T8
01

T9
01

T1
12

T5
01

L6
01

5V

GND

Va

GND

GND

NC

Vs

Vs

P811

<Fig. 1-1> Connection Diagram of Power Adjustment for

Measuring (Power Board): 42” XGA/VGA

VsADJ

VR951

5V

GND

Va

GND

GND

NC

Vs

Vs

P811

111

VaADJ

VR901

3.3VADJ

VR221

T8
01

T9

01
L8
51

T5
01

T1
12

L6
01

VsADJ

VR951

5V

GND

Va

GND

GND

NC

Vs

Vs

P811

111

VaADJ

VR901

VaADJ

VR901

3.3VADJ

VR221

T8
01

T9

01
L8
51

T5
01

T1
12

L6
01

<Fig. 1-2> Connection Diagram of Power Adjustment for

Measuring (Power Board): 50”

<Fig. 1-3> 50” PSU(Sanken: EAY32929001)

- 13 -

ADJUSTMENT INSTRUCTIONS

5-5. Adjustment(LG IT: EAY32957901)

(1) Va Adjustment

1) Connect + terminal of D.M.M to Va pin of P812 and
connect – terminal to GND pin of P812.

2) Adjust VR951 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

(2) Vs Adjustment

1) Connect + terminal of D.M.M to Vs pin of P812 and
connect – terminal to GND pin of P812.

2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)

6. ADC-Set Adjustment

6-1. Synopsis

ADC-Set adjustment to set the black level and the Gain to
optimum.

6-2. Test Equipment

Service R/C, 801GF(802V, 802F, 802R) or MSPG925FA
Pattern Generator
(480i/1080i The Horizontal 100% Color Bar Pattern adjust to
within 0.7±0.1Vp-p)

[ADC adjustment (MSPG-925Fx series) Model No. & Pattern No.]

- Model No.: #209(480i adjustment), #223(1080i adjustment)

- Pattern No.: #65(7ColorBar Pattern)

<Fig. 1-4> 50” PSU(LG IT: EAY32957901)

<Fig. 2> Adjustment Mode

<Fig. 3> Adjustment Pattern: 480i/1080i 60Hz HozTV31Bar

Pattern

- 14 -

ADJUSTMENT INSTRUCTIONS

6-3. Adjustment

(1) Select Component1 as the input with 100% Horizontal

Color Bar Pattern(HozTV31Bar) in 480i Mode

(2) After receiving signal for at least 1 second, press the ADJ

Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘2. ADC 480i Comp1’.
Pressing the Enter Key to adjust automatically.

(3) When the adjustment is over, 'MST3361 Component

Success’ is displayed. If the adjustment has errors,
'MST3361 Configuration Error’ is displayed.

(4) Select Component1 as the input with 100% Horizontal

Color Bar Pattern(HozTV31Bar) in 1080i Mode.

(5) After receiving signal for at least 1 second, press the ADJ

Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘3. ADC 1080i Comp1/RGB’.
Pressing the Enter Key to adjust automatically.

(6) When the adjustment is over, 'MST3361 Component

Success’ is displayed. If the adjustment has errors,
'MST3361 Configuration Error’ is displayed.

(7) After the Component MST3361 adjustment is over, convert

the RGB-DTV Mode and display Pattern.
When the adjustment is over, 'MST3361 RGB_DTV
Success’ is displayed.

(8) Readjust after confirming the case Pattern or adjustment

condition where the adjustment errors.

(9) After adjustment is complete, exit the adjustment mode by

pressing the ADJ KEY.

7. EDID(The Extended Display
Identification Data)/DDC
(Display Data Channel) Download

This is the function that enables “Plug and Play".

7-1. HDMI EDID Data Input

(1) Required Test Equipment

1) PC, Jig for adjusting DDC. (PC serial to D-sub
Connection equipment)

2) S/W for writing DDC(EDID data write & read)

3) D-Sub cable

4) Jig for HDMI Cable connection

(2) Preparation for Adjustments &

Setting of Device

1) Set devices as below and turn on the PC and JIG.

2) Open S/W for writing DDC (EDID data write & read).
(operated in DOS mode)

7-2. EDID DATA for PA-73E

[42PC5D-UC]

: EDID for HDMI-1 (DDC (Display Data Channel) Data)

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

__________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 02 20 00 00 00 FC
70 | 00 34 32 50 43 35 44 2D 55 43 0A 20 20 20 01 5D

EDID Block 1 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

__________________________________________________

0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28 55
20 | 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20 58
30 | 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 2D
40 | 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20
50 | E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A7

: EDID for HDMI-2 (DDC (Display Data Channel) Data)

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

__________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28
40 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
50 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 FC 00 34
60 | 32 50 43 35 44 2D 55 43 0A 20 20 20 00 00 00 FD
70 | 00 38 4B 1F 3C 09 00 0A 20 20 20 20 20 20 01 0D

EDID Block 1 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

__________________________________________________

0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 20 00 8C 0A D0 8A 20 E0 2D 10 10 3E 96
20 | 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10 10
30 | 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00 00 00
40 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 35

PDP TV SET

(or Digital Board)

- 15 -

ADJUSTMENT INSTRUCTIONS

: EDID for RGB-PC

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

___________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 68 73 41 96 0A CF 30 A3 57 4C B0 23
20 | 09 50 4E A1 08 00 01 01 01 01 01 01 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 34 32 50 43 35 44 2D 55 43 0A 20 20 20 00 77

[50PC5D-UC]

: EDID for HDMI-1 (DDC (Display Data Channel) Data)

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

___________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 02 20 00 00 00 FC
70 | 00 35 30 50 43 35 44 2D 55 43 0A 20 20 20 01 5E

EDID Block 1 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

____________________________________________________

0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28 55
20 | 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20 58
30 | 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 2D
40 | 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20
50 | E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 A7

: EDID for HDMI-2 (DDC (Display Data Channel) Data)

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

___________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01
30 | 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28
40 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
50 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 FC 00 35
60 | 30 50 43 35 44 2D 55 43 0A 20 20 20 00 00 00 FD
70 | 00 38 4B 1F 3C 09 00 0A 20 20 20 20 20 20 01 0E

EDID Block 1 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

____________________________________________________

0 | 02 03 15 F1 46 84 05 03 02 20 22 23 15 07 50 65
10 | 03 0C 00 20 00 8C 0A D0 8A 20 E0 2D 10 10 3E 96
20 | 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10 10
30 | 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00 00 00
40 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 35

: EDID for RGB-PC

EDID Block 0 table =

0 1 2 3 4 5 6 7 8 9 A B C D E F

___________________________________________________

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 00 10 01 03 68 73 41 96 0A CF 30 A3 57 4C B0 23
20 | 09 50 4E A1 08 00 01 01 01 01 01 01 01 01 01 01
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30
50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38
60 | 4B 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 35 30 50 43 33 44 2D 55 45 0A 20 20 20 00 78