LG 50LB5800 Owner’s Manual
OWNER’S MANUAL
LED TV*
* LG LED TVs are LCD TVs with LED backlighting.
Please read this manual carefully before operating your set and retain it for future reference.
LB58**
*MFL68027133* |
www.lg.com |
|
P/NO : MFL68027133 (1411-REV06) |
||
|
||
|
Printed in Korea |
<![endif]>ENGLISH
2 LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
Licenses
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
EXTERNAl CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com.
SAFETY INSTRUCTIONS |
3 |
Safety Instructions
Please read these safety precautions carefully before using the product.
WARNING
yyDo not place the TV and/or remote control in the following environments:
--A location exposed to direct sunlight --An area with high humidity such as a
bathroom
--Near any heat source such as stoves and other devices that produce heat
--Near kitchen counters or humidifiers where they can easily be exposed to steam or oil
--An area exposed to rain or wind
--Near containers of water such as vases Otherwise, this may result in fire, electric shock, malfunction or product deformation.
yyDo not place the product where it might be exposed to dust.
This may cause a fire hazard.
yyMains Plug is the TV connecting/ disconnecting device to AC mains electric supply. This plug must remain readily attached and operable when TV is in use.
yyDo not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.
You may be electrocuted due to excess moisture.
yyMake sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on earth.) Otherwise possibility you may be electrocuted or injured.
yyInsert power cable plug completely into wall socket otherwise if not secured completely into socket, fire ignition may break out.
yyEnsure the power cord does not come into contact with hot objects such as a heater. This may cause a fire or an electric shock hazard.
yyDo not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
yyBend antenna cable between inside and outside building to prevent rain from flowing in.
This may cause water damaged inside the Product and could give an electric shock.
<![endif]>ENGLISH
<![endif]>ENGLISH
4 SAFETY INSTRUCTIONS
yyWhen mounting TV onto wall make sure to neatly install and isolate cabling from rear of TV as to not create possibility of electric shock /fire hazard.
yyDo not plug too many electrical devices into a single multiple electrical outlet. Otherwise, this may result in fire due to over-heating.
yyDo not drop the product or let it fall over when connecting external devices.
Otherwise, this may result in injury or damage to the product.
yyDispose of used batteries carefully to ensure that a small child does not consume them. Please seek DoctorMedical Attention immediately if child consumes batteries.
yyDo not insert any metal objects/conductors (like a metal chopstick/cutlery/screwdriver) between power cable plug and input Wall
Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal. You may be electrocuted. (Depending on model)
yyDo not put or store inflammable substances near the product. There is a danger of combustion/explosion or fire due to careless handling of the inflammable substances.
yyKeep the anti-moisture packing material or vinyl packing out of the reach of children.
Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
Desiccant
yyDo not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.
yyDo not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable objects such as paper and matches. Children must pay particular attention. Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre.
yyDo not spray water on the product or scrub with an inflammable substance (thinner or benzene). Fire or electric shock accident can occur.
SAFETY INSTRUCTIONS |
5 |
yyDo not allow any impact, shock or any objects to fall into the unit, and do not drop anything onto the screen.
You may be injured or the product can be damaged.
yyNever touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
yyNever touch the wall outlet when there is leakage of gas, open the windows and ventilate.
It may cause a fire or a burn by a spark.
yyDo not disassemble, repair or modify the product at your own discretion.
Fire or electric shock accident can occur. Contact the service centre for check, calibration or repair.
yyIf any of the following occur, unplug the product immediately and contact your local service centre.
--The product has been impacted by shock
--The product has been damaged
--Foreign objects have entered the product --The product produced smoke or a strange
smell
This may result in fire or electric shock.
yyUnplug the TV from AC mains wall socket if you do not intend to use the TV for a long period of time. Accumulated dust can cause fire hazard and insulation deterioration can cause electric leakage/shock/fire.
yyApparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
yyDo not install this product on a wall if it could be exposed to oil or oil mist.
This may damage the product and causeit to fall.
CAUTION
yyInstall the product where no radio wave occurs.
yyThere should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.
This may cause an electric shock.
yyDo not install the product on places such as unstable shelves or inclined surfaces.
Also avoid places where there is vibration or where the product cannot be fully supported.
Otherwise, the product may fall or flip over, which may cause injury or damage to the product.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 SAFETY INSTRUCTIONS
yyIf you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.
yyIf you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
yyOnly use the attachments / accessories specified by the manufacturer.
yyWhen installing the antenna, consult with a qualified service technician. If not installed by a qualified technician, this may create a fire hazard or an electric shock hazard.
yyWe recommend that you maintain a distance of at least 2 to 7 times the diagonal screen size when watching TV.
If you watch TV for a long period of time, this may cause blurred vision.
yyOnly use the specified type of battery.
This could cause damage to the remote control.
yyDo not mix new batteries with old batteries. This may cause the batteries to overheat and leak.
yyBatteries should not be exposed to excessive heat. For example, keep away from direct Sunlight, open fireplace and electric heaters.
yyDo not place non-rechargeable batteries in charging device.
yyMake sure there are no objects between the remote control and its sensor.
yySignal from Remote Control can be interrupted due to external/internal lighting eg Sunlight, fluorescent lighting.If this occurs turn off lighting or darken viewing area.
yyWhen connecting external devices such as video game consoles, make sure the connecting cables are long enough.
Otherwise, the product may fall over, which may cause injury or damage the product.
yyDo not turn the product On/Off by pluggingin or unplugging the power plug to the
wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
yyPlease follow the installation instructions below to prevent the product from overheating.
--The distance between the product and the wall should be more than 10 cm.
--Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard).
--Do not install the product on a carpet or cushion.
--Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
SAFETY INSTRUCTIONS |
7 |
yyTake care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot. This does not affect the operation or performance of the product.
yyPeriodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
yyPrevent dust collecting on the power plug pins or outlet.
This may cause a fire hazard.
yyProtect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
yyDo not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it, as it may cause damage to screen.
yyAvoid touching the screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary or permanent distortion/damage to screen.
yyWhen cleaning the product and its components, unplug the power first and wipe it with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water
or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage (deformation, corrosion or breakage).
yyAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
yyWhen unplugging the cable, grab the plug and unplug it, by pulling at the plug. Don’t pull at the cord to unplug the power cord from the power board, as this could be hazardous.
yyWhen moving the product, make sure you turn the power off first. Then, unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire hazard or cause electric shock.
yyWhen moving or unpacking the product, work in pairs because the product is heavy. Otherwise, this may result in injury.
<![endif]>ENGLISH
<![endif]>ENGLISH
8 SAFETY INSTRUCTIONS
yyContact the service centre once a year to clean the internal parts of the product.
Accumulated dust can cause mechanical failure.
yyRefer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
yyIf the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with product.
yyThe panel is a high technology display product with resolution of two million to six million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
yyYou may find different brightness and colour of the panel depending on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.
yyDisplaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video game) for a prolonged time may cause damage to the screen, resulting in retention of the image, which is known as image sticking. The warranty does not cover the product for image sticking.
Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to tempera-ture and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depend-ing on the product.
This generated sound does not affect the performance and reliability of the product.
yyDo not use high voltage electrical goods near the TV (e.g. electric mosquito-swatter). This may result in product malfunction.
ASSEMBLING AND PREPARING |
9 |
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you are using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.
<![endif]>ENGLISH
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
|
B |
B |
|
|
< |
10 mm |
|
|
|
||
|
|
*A = |
|
|
|
< |
18 mm |
A |
|
*B = |
|
|
A |
|
yy Use a certified cable with the HDMI logo attached.
yy If you do not use a certified HDMI cable, the screen may not display or a connection error may occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/™ Cable
-- High-Speed HDMI®/™ Cable with Ethernet
10 ASSEMBLING AND PREPARING
<![if ! IE]><![endif]>ENGLISH
|
|
|
|
|
|
|
|
|
Remote control, Batteries |
Owner’s Manual |
|
Cable Holder |
|||||
(AAA) |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
Cable Managements |
|
Power Cord |
|
Wall Mount Spacers |
2EA |
|
|
|
2EA |
|
|
|
|
(Only 42LB58**) |
|
|
|
|
|
Stand Screws |
Stand Screws |
|
Stand Bases |
|
4EA, M4 x L20 |
4EA, M4 x L14 |
|
(Only |
|
(Only 32LB58**) |
(Only |
|
32/39/42/47/50/55/60LB58**) |
|
|
|
39/42/47/50/55/60/65LB58**) |
|
|
|
|
|
|
|
Stand Assys
(Stand Body/Stand Base)
(Only 65LB58**)
ASSEMBLING AND PREPARING |
11 |
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.
AN-MR500 |
|
AN-VC5** |
|
LG Audio Device |
Magic remote |
|
Video call camera |
|
|
|
|
|
|
|
AN-WF500 |
|
|
|
|
Wi-Fi/Bluetooth Dongle |
|
|
|
|
|
|
|
|
|
*You can use the Magic Remote and LG Audio Device(Wireless) only when you are using the Wi-Fi/ Bluetooth Dongle.
<![endif]>ENGLISH
12 ASSEMBLING AND PREPARING
Parts and buttons
<![if ! IE]><![endif]>ENGLISH
Screen
Joystick Button2
Remote control and
Intelligent1 sensors
Power Indicator
1Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2Joystick Button - This button is located below the TV screen.
NOTE
yy You can set the Power indicator Light to on or off by selecting OPTION in the main menus.
ASSEMBLING AND PREPARING |
13 |
Using the Joystick button
You can simply operate the TV functions by pressing to turn On/Off or sliding your finger over joystick button moving up, down, left or right.
Basic Functions
Power On
Power Off
Volume
Control
Programmes
Control
When the TV is turned off, place your finger on the joystick button and press it once and release it.
When the TV is turned on, place your finger on the joystick button and press it once for a few seconds and release it. (However, if the Menu button is on the screen, pressing and holding the joystick button will let you exit the Menu.)
If you place your finger over the joystick button and move it left or right, you can adjust the volume level you want.
If you place your finger over the joystick button and move it up or down, you can scrolls through the saved programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not to press the joystick button. If you press the joystick button first, you may not be able to adjust the volume level and saved programmes.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items(
) moving the joystick button up, down, left or right.
TV off |
Turns the power off. |
|
Settings |
Accesses the main menu. |
|
Close |
Closes Clears on-screen displays and returns to |
|
TV viewing. |
||
|
||
Input List |
Changes the input source. |
<![endif]>ENGLISH
Loading...