Quick Reference Guide
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it for future reference.
42LP870H
47LP870H
55LP870H
P/NO : MFL67694922 (1312-REV01) |
www.lgsolutions.com |
<![endif]>ENGLISH
2 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.
|
Read these instructions. |
|
|
Keep these instructions. |
|
WARNING/CAUTION |
||
Heed all warnings. |
||
|
Follow all instructions. |
|
RISK OF ELECTRIC SHOCK |
||
|
||
DO NOT OPEN |
|
|
|
|
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
CAUTION
If you ignore the caution message, you may be slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the product safely. Please read the note carefully before using the product.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
yyDo not use this apparatus near water.
yyClean only with a dry cloth.
yyDo not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
yyDo not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
yyDo not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet (Can differ by country).
yyDo not press strongly upon the panel with a hand or a sharp object such as a nail, pencil or pen, or make a scratch on it.
Wash hands after handling.
IMPORTANT SAFETY INSTRUCTIONS |
3 |
yyProtect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
yyOnly use attachments/accessories specified by the manufacturer.
yyUse only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
yyUnplug this apparatus during lightning storms or when unused for long periods of time.
yyRefer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
yyDo not stick metal objects or any other conductive material into the power cord. Do not touch the end of the power cord while it is plugged in.
yyKeep the packing anti-moisture material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
yyCAUTION concerning the Power Cord (Can differ by country):
It is recommended that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do
not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not move the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
yyWarning - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.
yyDo not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
<![endif]>ENGLISH
<![endif]>ENGLISH
4 IMPORTANT SAFETY INSTRUCTIONS
yyGrounding
(Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power Supply
Short-circuit
Breaker
yyAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.
yyDo not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
yyOutdoor Antenna Grounding (Can differ by country): If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
Ground Clamp |
|
|
|
|
|
|
|
|
|
|
|
Antenna Lead in Wire |
||
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
Antenna Discharge Unit |
||||||||||
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Electric Service |
|
|
|
|
|
|
|
|
|
|
|
|
(NEC Section 810-20) |
|
Equipment |
|
|
|
|
|
|
|
|
|
Grounding Conductor |
||||
Ground Clamp |
|
|
|
|
|
|
|
|
|
|
|
|
(NEC Section 810-21) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
Power Service Grounding |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NEC: National Electrical Code |
Electrode System |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(NEC Art 250, Part H) |
yyCleaning
When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzine.
yyMoving
Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.
yyVentilation
Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places.
yyIf you smell smoke or other odors coming from the TV, unplug the power cord and contact an authorized service center.
yyKeep the product away from direct sunlight. yyNever touch this apparatus or antenna during a
thunder or lightning storm.
yyWhen mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.
yyDo not allow an impact shock or any objects to fall into the product, and do not drop anything onto the screen.
yyDisconnecting the Main Power
The power outlet used with this device must remain easily accessible.
yyStore the accessories (battery, etc.) in a safe location out of the reach of children.
yyThis apparatus use batteries. In your community there might be regulations that require you
to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.
yyDo not dispose of batteries in a fire.
yyDo not short circuit, disassemble or allow the batteries to overheat.
|
|
|
|
IMPORTANT SAFETY INSTRUCTIONS |
5 |
||
yyDot Defect |
For USA and Canada |
|
|
||||
|
The Plasma or LCD panel is a high technology |
|
|||||
|
|
|
|
|
|
||
|
product with resolution of two million to six million |
|
|
|
|
|
|
|
pixels. In a very few cases, you could see fine dots |
|
|
|
|
|
|
|
|
FCC NOTICE |
|
|
|
||
|
on the screen while you’re viewing the TV. Those |
|
|
|
|||
|
dots are deactivated pixels and do not affect the |
This equipment has been tested and found to |
|
||||
|
performance and reliability of the TV. |
|
|||||
|
comply with the limits for a Class B digital device, |
|
|||||
yyGenerated Sound |
|
||||||
pursuant to Part 15 of the FCC Rules. These limits |
|
||||||
|
“Cracking” noise: A cracking noise that occurs |
|
|||||
|
are designed to provide reasonable protection |
|
|||||
|
when watching or turning off the TV is generated by |
|
|||||
|
against harmful interference in a residential |
|
|||||
|
plastic thermal contraction due to temperature and |
|
|||||
|
installation. This equipment generates, uses and can |
|
|||||
|
humidity. This noise is common for products where |
|
|||||
|
radiate radio frequency energy and, if not installed |
|
|||||
|
thermal deformation is required. |
|
|||||
|
and used in accordance with the instructions, may |
|
|||||
|
Electrical circuit humming/panel buzzing: A low level |
|
|||||
|
cause harmful interference to radio communications. |
|
|||||
|
noise is generated from a high-speed switching |
|
|||||
|
However, there is no guarantee that interference |
|
|||||
|
circuit, which supplies a large amount of current |
|
|||||
|
will not occur in a particular installation. If this |
|
|||||
|
to operate a product. It varies depending on the |
|
|||||
|
equipment does cause harmful interference to radio |
|
|||||
|
product. |
|
|||||
|
or television reception, which can be determined |
|
|||||
|
This generated sound does not affect the |
|
|||||
|
by turning the equipment off and on, the user is |
|
|||||
|
performance and reliability of the product. |
|
|||||
|
encouraged to try to correct the interference by one |
|
|||||
yyTake care not to touch the ventilation openings. |
|
||||||
or more of the following measures: |
|
||||||
|
When watching the TV for a long period, the |
|
|||||
|
|
- Reorient or relocate the receiving antenna. |
|
||||
|
ventilation openings may become hot. This does |
|
|
||||
|
not affect the performance of the product or cause |
|
- Increase the separation between the |
|
|||
|
defects in the product. |
|
equipment and the receiver. |
|
|||
yyIf the TV feels cold to the touch, there may be a |
|
- Connect the equipment to an outlet on a circuit |
|
||||
|
small “flicker” when it is turned on. This is normal, |
|
different from that to which the receiver is |
|
|||
|
there is nothing wrong with TV. Some minute dot |
|
connected. |
|
|||
|
defects may be visible on the screen, appearing as |
|
- Consult the dealer or an experienced radio/TV |
|
|||
|
tiny red, green, or blue spots. However, they have |
|
technician for help. |
|
|||
|
no adverse effect on the TV’s performance. Avoid |
This device complies with part 15 of the FCC Rules. |
|
||||
|
touching the LCD screen or holding your finger(s) |
Operation is subject to the following two conditions: |
|
||||
|
against it for long periods of time. Doing so may |
(1) this device may not cause harmful interference |
|
||||
|
produce some temporary distortion effects on the |
and (2) this device must accept any interference |
|
||||
|
screen. |
received, including interference that may cause |
|
||||
|
|
|
undesired operation of the device. |
|
|||
|
Preventing “Image burn” or “Burn-in” on your TV |
Any changes or modifications in construction of |
|
||||
|
this device which are not expressly approved by |
|
|||||
|
screen |
|
|
||||
|
|
the party responsible for compliance could void the |
|
user’s authority to operate the equipment.
NOTE TO CABLE/TV INSTALLER
yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.
yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.
yyAvoid displaying a fixed image on the TV screen for a long period of time to prevent image burn.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model. For more information about licenses, visit ‘www.lg.com’.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274”
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol & DTS and the Symbol together are registered trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit ‘http://opensource.lge.com’.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to ‘opensource@lge.com’. This offer is valid for three (3) years from the date on which you purchased the product.
TABLE OF CONTENTS
2 IMPORTANT SAFETY INSTRUCTIONS
6 LICENSES
6OPEN SOURCE SOFTWARE NOTICE
7TABLE OF CONTENTS
8Installation Procedure
8 ASSEMBLING AND PREPARING
8 Unpacking
10Optional Extras
11Parts and Buttons
13Lifting and Moving the TV
14Setting Up the TV
14- Attaching the Stand
15- Mounting on a Table
17- Mounting on a Wall
18- External Speaker Out
18- Tidying Cables
19REMOTE CONTROL
21 SPECIFICATIONS
23 TROUBLESHOOTING
TABLE OF CONTENTS |
7 |
<![endif]>ENGLISH
NOTE
yyImage shown may differ from your TV. yyYour TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
yyThe available menus and options may differ from the input source or product model that you are using.
yyNew features may be added to this TV in the future.
<![endif]>ENGLISH
8 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
Installation Procedure
1Open the package and make sure all the accessories are included.
2Attach the stand to the TV set.
3Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yyDo not use any unapproved items to ensure the safety and product life span.
yyAny damages or injuries by using unapproved items are not covered by the warranty.
yySome models appear to have a thin film on the screen. It is actually part of the screen, do not remove it.
NOTE
yyThe items supplied with your product may vary depending on the model.
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width.
yyUse an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
AA
*A 10 mm (0.39 inches) *B
18 mm (0.7 inches)
ASSEMBLING AND PREPARING 9
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Quick Reference Guide |
|
|
||
Remote Control, Batteries (AAA) |
|
|
Power Cord |
|||||||||
(See p. 19) |
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Stand Body, Stand Base |
Stand Screws |
Torx Plus |
(See p. 14) |
4 EA, M4 x 20 |
Star-Head Screw |
|
4 EA, M4 x 16 |
2 EA |
|
(See p. 14) |
(See p. 14) |
<![endif]>ENGLISH
Desk-Mount Screw |
|
Nuts for Stand Fixing |
|
Washers for Stand Fixing |
1 EA |
|
2 EA |
|
2 EA |
(See p. 15) |
|
(See p. 16) |
|
(See p. 16) |
|
|
|
|
|
Screws for Stand Fixing |
Cable Holder |
|
Power Cord Holder, 1 EA |
|
2 EA |
(See p. 18) |
|
Coaxial Cable Holder, 1 EA |
|
(See p. 16) |
|
|
(See p. 18) |
|
|
|
|
|
|
A/V Adapter Cable