LG 47LH90-UB User Manual

Please read this manual carefully before operating
your set and retain it for future reference.

The model and serial number of the TV is located
on the back and one side of the TV.

Record it below should you ever need service.

LCD TV
OWNER’S MANUAL

42LH90
47LH90
55LH90

P/NO : SAC33601906 (0905-REV01)

www.lgusa.com / www.lg.ca

This product qualifies for ENERGY STAR in the “factory
default (Home Use)” setting.

Changing the factory default settings or enabling other fea­tures may increase power consumption that could exceed the
limits necessary to qualify for ENERGY STAR.

Model:

Serial:

1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User
1-888-542-2623 CANADA

LG Customer Information Center

2

WARNING / CAUTION

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the litera­ture accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi­tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation (of the device).

Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

3

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com­bination to avoid injury from tip-over.

Unplug this apparatus during lighting storms
or when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power­supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.

1

2

3

4

5

7

8

6

9

10

4

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during
a thunder or lighting storm.

When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.

Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.

CAUTION concerning the Power Cord:
It is recommend that appliances be placed

upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.

Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.

Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).

GGRROOUUNNDD IINNGG
Ensure that you connect the earth ground wire

to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC out­let). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The

plug must remain readily operable.

As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.

12

11

14

13

16

17

18

19

Power
Supply

Short-circuit

Breaker

15

5

AANNTTEENNNNAASS
OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg
If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna system
should not be located in the vicinity of over­head power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.

Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.

Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding
electrode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700

CClleeaa nniinngg
When cleaning, unplug the power cord and

scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.

MMoovviinn gg
Make sure the product is turned off,

unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.

VVeennttiillaattiioonn
Install your TV where there is proper ventila-

tion. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.

If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the power
cord contact an authorized service center.

Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.

Keep the product away from direct sunlight.

FFoorr LLCC DD TTVV

If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.

Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary dis­tortion effects on the screen.

20

23

24

25

26

27

21

22

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

6

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 3

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stand Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Cable Management

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Kensington Security System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Securing the TV to the wall to prevent falling when
the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 19

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

USB Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Audio out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Initial Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Quick Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . .40

- Add / Delete Channel (Manual Tuning) . . . . . . 41

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Channel List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Favorite Channel Setup / Favorite Channel List

. .

44

Brief Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45

Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Input Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

AV Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Simple Manual

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Key Lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

SIMPLINK

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

USB

Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Movie List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Divx Registration Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Deactivation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 66

Picture Wizard

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Preset Picture Settings (Picture Mode)

. . . . . . . . . . . . . 70

Manual Picture Adjustment - User Mode

. . . . . . . . . . 71

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 72

Expert Picture Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Energy Saving

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Power Indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Demo Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

79
LED Local Dimming

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

7

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . .81

Clear Voice II

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Preset Sound Setting (Sound Mode)

. . . . . . . . . . . . . . . . .83

Sound Setting Adjustment - User Mode

. . . . . . . . . . . 84

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Stereo/SAP Broadcasts Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 88

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

On-Screen Menus Language Selection

. . . . . . . . . . . . . 90

Caption Mode

- Analog Broadcasting System Captions

. . . . . . . 91

- Digital Broadcasting System Captions

. . . . . . . . 92

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

94

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 2

Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

113

External Control Through RS-232C

. . . . . . . . . . . . . . . . .114

Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 0

8

FEATURE OF THIS TV

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma TV).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN

AV Mode is three preset picture and audio settings. It
allows the viewer to quickly switch between common set­tings. It includes Cinema, Sports, and Game Modes.

Displays HDTV programs in full 1920 x 1080p resolu­tion for a more detailed picture.

Automatically enhances and amplifies the sound of
human voice frequency range to help keep dialogue
audible when background noise swells.

A unique invisible speaker system tuned by renowned
audio expert, Mr. Mark Levinson. Speakers are embed­ded in strategic spots behind the front cabinet and
use minute vibrations to turn the entire front bezel
into the speaker system. The result s a clean, polished
look, and enhanced audio by increasing the “sweet
spot”, giving a wider and richer sound field.

HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

This TV contains the detailed calibrations necessary
for professional certification by the Imaging Science
Foundation. The resulting ISF “day” and “night” modes
will then be accessible by the user to experience the
best their LG HDTV has to offer.
Sophisticated and detailed calibrations can be made
through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an
ISF certified technician.

High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.

TruMotion 240Hz displays 240 scenes
per second by combining advanced
120Hz technology with scanning back
light. This technology is verified from
Intertek & TüV Rheinland.

“DivX Certified to play DivX video up to HD 1080p,
including premium content”

ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX,Inc. This is an official DivX Certified
device that plays DivX video. Visit www.divx.com for
more information and software tools to convert your
files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
DivX Video-on-Demand (VOD) content. To generate
the registration code, locate the DivX VOD section in
the device setup menu. Go to vod.divx.com with this
code to complete the registration process and learn
more about DivX VOD.

THX (Thomlinson Holman’s Experiment) is the audio
and video certification standard of THX established
by George Lucas, who directed the movie Star Wars,
and Thomlinson.
This is the product to be certified in THX display area
and guarantees screen quality that exceeds the display
standard specification in both hardware and software.

PREPARATION

9

ACCESSORIES

PREPARATION

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

1.5V 1.5V

Owner’s Manual Power Cord

Remote Control,

Batteries

FAV

MUTE

Q. MENU

MENU

AV MODE

RETURN

VOL

CH

123

456

78

0

9

FLASHBK

P
A

G

E

INPUT

INFO

LIST

ENTER

POWER

TV

ENERGY SAVING

ON/OFF

MARK

CD Manual

OOppttiioonn EExxttrraass

* Wipe spots on the exterior only with

the polishing cloth.

* Do not wipe roughly. Excessive pres-

sure may cause scratches or discol­oration.

Polishing Cloth

Not included with all models

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.

Protection Cover

Screws for stand

assembly

(Refer to P.12)

Screw for stand fixing

(Refer to P.17)

x 4

(For 42/47LH90) (For 42LH90)

PREPARATION

10

FRONT PANEL INFORMATION

PREPARATION

■

Image shown may differ from your TV.

CHANNEL ( , )
Buttons

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

AC power control switch

SPEAKER

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates white when the TV is switched on.
(Can be adjusted using the

PPoo wweerr IInnddiiccaattoorr

in the OPTION menu.

GG

pp..77 88

)

Remote Control Sensor,
Intelligent Sensor

Adjusts picture according to
the surrounding conditions

CH

VOL

ENTER

MENU

INPUT

PREPARATION

11

BACK PANEL INFORMATION

■

Image shown may differ from your TV.

( )

( )

R

1 2 3

6 57

9

1

8

2

4

AV (Audio/Video) IN

Analog composite connection. Supports standard
definition video only (480i).

HDMI/DVI IN, HDMI IN

Digital Connection.
Supports HD video and Digital audio. Doesn’t

support 480i.
Accepts DVI video using an adapter or HDMI to

DVI cable (not included).

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).

AUDIO IN (RGB/DVI)

1/8" (0.32 cm) headphone jack for analog PC
audio input.

OPTICAL DIGITAL AUDIO OUT

Digital optical audio output for use with amps and
home theater systems.

Note: In standby mode, this port doesn’t work.

ANTENNA/CABLE IN

Connect over-the air signals to this jack.
Connect cable signals to this jack.

RS-232C IN (CONTROL & SERVICE) PORT

Used by third party devices.
This port is used for Service or Hotel mode.

COMPONENT IN

Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red

and white for audio.

USB IN

Used for viewing photos/movies and listening to
MP3s.

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

1

2

3

4

8

9

7

6

5

AV IN 1

(

)

MONO

AUDIOVIDEO

2

1

LR

VIDEO

COMPONENT IN

L R

AUDIO

3

2

1

/DVI IN

RGB IN (PC)

AUDIO IN

(RGB/DVI)

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/

CABLE IN

USB IN

IN 4

R

AUDIO

L/ MONO

VIDEO

AV IN 2

PREPARATION

12

STAND INSTRUCTIONS

PREPARATION

■

Image shown may differ from your TV.

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the TV as shown.

Fix the 4 screws securely using the holes in the
back of the TV.

1

2

3

INSTALLATION (

For 42/47LH90)

GG

When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened
fully, the TV can tilt forward after the product
installation). Do not over tighten.

NOTE

!

PREPARATION

13

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Remove the screws from the TV.

2

Detach the stand from the TV.

3

PROTECTION COVER

Insert the

PPRROOTTEECCTTIIOONN CCOOVVEERR

into the TV.
After removing the protection paper from the
protection cover, adhere it to the TV as shown.

4

PREPARATION

14

VESA WALL MOUNTING

PREPARATION

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

GG

Do not install your wall mount kit while your TV is turned on. It may result in personal
injury due to electric shock.

CAUTION

GG

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

GG

Standard dimensions for wall mount kits are shown
in the table.

GG

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

GG

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to
the TV.

GG

For wall mounts that do not comply with the VESA

standard screw specifications, the length of the
screws may differ depending on their specifica­tions.

GG

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.

GG

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

Model

VESA (A *B)

Standard Screw Quantity

Wall Mounting Bracket

(sold separately)

55 LH 90

42L H90 ,

47LH90

200* 200 M6 4

400* 400 M6 4

AW-55LH40M

AA

BB

AW-47LG30M

PREPARATION

15

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as
shown.

CABLE MANAGEMENT CLIP

1

2

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

PREPARATION

16

DESKTOP PEDESTAL INSTALLATION

PREPARATION

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

■

Image shown may differ from your TV.

4 inches

GG

Ensure adequate ventilation by following the clearance recommendations.

GG

Do not mount near or above any type of heat source.

CAUTION

4 inches

4 inches

4 inches

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.

PREPARATION

17

ATTACHING THE TV TO A DESK (For 42LH90)

KENSINGTON SECURITY SYSTEM

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.

GG

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

■

Image shown may differ from your TV.

■

This feature is not available for all models.

- The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington
Security System cable as shown below.

- For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with

the Kensington Security System.
For further information, contact

hhttttpp::////wwwwww..kkeennssiinnggttoonn ..ccoomm

, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD
projectors.

NOTE: The Kensington Security System is an optional accessory.

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.

■

You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

■

Image shown may differ from your TV.

GG

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.

GG

To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

NOTE

!

PREPARATION

18

SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND

PREPARATION

PREPARATION

19

ANTENNA OR CABLE CONNECTION

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

■

Image shown may differ from your TV.

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wall
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire
when connecting the antenna.

Copper Wire

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA/

CABLE IN

R

ANTENNA/

CABLE IN

R

EXTERNAL EQUIPMENT SETUP

20

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.

Component Connection

1. How to connect

Connect the video outputs (Y, P

B, PR

)

of the digital set-

top box to the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11

or

22

jacks on the TV. Match the jack colors (Y = green, P

B =

blue, and P

R = red).

Connect the audio output of the digital set-top box to
the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11

or

22

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box operation.

)

■

Select the

CCoommppoonneenntt 11

or

22

input source on the TV

using the

IINNPPUUTT

button on the remote control.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

Y, CB/PB, CR/PR

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

1920x1080p

Signal

480i
480p
720p

10 8 0 i

10 8 0 p

Component

Yes
Yes
Yes
Yes
Yes

HDMI

No
Yes
Yes
Yes
Yes

AV IN 1

2

3

1

MONO

( )

AUDIOVIDEO L R

/DVI IN

VIDEO

AUDIO

L R

COMPONENT IN

2

1

Y L RPB PR

1

2

EXTERNAL EQUIPMENT SETUP

21

HDMI Connection

Connect the digital set-top box to

HHDDMMII//DDVVII IINN 11

,

22, 33

, or

44

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HHDDMMII11, HHDDMMII22, HHDDMMII33

, or

HHDDMMII44

input

source on the TV using the

IINNPPUUTT

button on the remote

control.

2

1

HDMI-DTV

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67. 432 59. 94

67.50 60.00

Resolution

720x480p

1280x720p

1920x1080i

1920x1080p

( )

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

O

A

C

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOVIDEO L R

2

3

1

/DVI IN

HDMI OUTPUT

1

GG

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

GG

HDMI mode supports PCM, Dolby Digital audio format.

NOTE

!

EXTERNAL EQUIPMENT SETUP

22

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

( )

( )

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIG

AUDIO OU

ANTENNA

CABLE IN

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOLR

2

3

1

/DVI IN

AUDIO IN

(RGB/DVI)

L R

DVI OUTPUT

AUDIO

1

2

GG

A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio
connection is necessary.

NOTE

!

Connect the DVI output of the digital set-top box to
the

HHDDMMII//DDVVII IINN 11, 22

, or 33jack on the TV.

Connect the digital set-top box audio output to the
AAUUDDIIOO IINN ((RR GGBB//DDVVII

))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HHDDMMII11, HHDDMMII22

, or

HHDDMMII33

input source on the

TV using the

IINNPPUUTT

button on the remote control.

2

1

EXTERNAL EQUIPMENT SETUP

23

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the
component input ports as shown below.

Component ports on the TV

YPB PR

Video output ports

on DVD player

Y

Y

Y

Y

PB

B-Y

Cb

Pb

P

R

R-Y

Cr

Pr

Connect the video outputs (Y, PB

, PR

)

of the DVD to the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11

or

22

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and PR = red

)

.

Connect the audio outputs of the DVD to the
CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11

or 22jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

CCoommppoonneenntt 11

or 22input source on the TV

using the

IINNPPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

AV IN 1

2

3

1

MONO

( )

AUDIOVIDEO L R

/DVI

VIDEO

AUDIO

L R

COMPONENT IN

2

1

Y L RPB PR

1 2

EXTERNAL EQUIPMENT SETUP

24

EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

VIDEO

AUDIO

L R

COMPONENT IN

2

3

1

2

1

/DVI IN

( )

AV IN 1

MONO

( )

AUDIOVIDEO LR

L R

VIDEO

AUDIO

HDMI Connection

( )

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

OPT

A

AN

C

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOVIDEO L R

2

3

1

/DVI IN

HDMI OUTPUT

( )

1

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks between TV and
DVD. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

AAVV11

or

AAVV22

input source on the TV using the

IINNPPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

1

Connect the HDMI output of the DVD to the
HHDDMMII//DDVVII IINN 11, 22, 33

or 44jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HHDDMMII11, HHDDMMII22, HHDDMMII33

, or

HHDDMMII44

input

source on the TV using the

IINNPPUUTT

button on the remote

control.

■

Refer to the DVD player's manual for operating instructions.

2

1

GG

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

NOTE

!

1

EXTERNAL EQUIPMENT SETUP

25

VCR SETUP

Antenna Connection

Connect the RF antenna out socket of the
VCR to the

AANNTTEENNNNAA// CCAA BBLLEE IINN

sock-

et on the TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

RGB IN (PC)

ANTENNA/
CABLE IN

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

AUDIO

Wall Jack

Antenna

1

2

Composite (RCA) Connection

GG

If you have a mono VCR, connect the audio cable from
the VCR to the

AAUU DDIIOO LL((MMOONNOO))

jack of the TV.

NOTE

!

VIDEO

AUDIO

L R

COMPONENT IN

2

3

1

2

1

/DVI

AV IN 1

MONO

( )

AUDIOVIDEO LR

L R

S-VIDEO VIDEO

AUDIO

OUTPUT
SWITCH

ANT IN

ANT OUT

1

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR.
(

Refer to the VCR owner’s manual.

)

■

Select the

AAVV11

input source on the TV using the

IINNPPUUTT

button on the remote control.

■

If connected to

AAVV IINN 22

, select

AAVV22

input source on the TV.

1

EXTERNAL EQUIPMENT SETUP

26

PC SETUP

EXTERNAL EQUIPMENT SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/

CABLE IN

2

3

1

R

/DVI IN

AUDIO IN

(RGB/DVI)

RGB IN (PC)

RGB OUTPUT

AUDIO

2

1

Connect the VGA output of the PC to the

RR GGBB IINN

((

PP CC

))

jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO IINN

((

RRGGBB//DDVVII

))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

RR GGBB--PP CC

input source on the TV using the

IINNPPUUTT

button on the remote control.

2

1

DVI to HDMI Connection

( )

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

OP

A

A

C

RGB IN (PC)

AV IN 1

MONO

( )

AUDIOVIDEO L R

AUDIO IN

(RGB/DVI)

2

3

1

/DVI IN

AUDIO

DVI OUTPUT

1

2

Connect the DVI output of the PC to the

HHDDMMII//DDVVII

IINN 11, 22

, or 33jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO IINN

((RRGGBB// DDVVII))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

HHDDMMII11, HHDDMMII22

, or

HHDDMMII33

input source on

the TV using the

IINNPPUUTT

button on the remote control.

2

1

GG

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

NOTE

!

EXTERNAL EQUIPMENT SETUP

27

NOTES

!

Supported Display Specifications (RGB-PC, HDMI-PC)

Resolution

720x400

640x350

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.09

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.776 59.87

47.712 60.015

63.981 60.02

75.00 60.00

66.587 59.934

67.50 60.00

640x480

800x600

1024x768

1280x768

1280x1024

1360x768

1600x1200

1920x1080

RGB-PC

1920x1080

HDMI-PC

GG

To get the best picture quality, adjust the PC graph­ics card to 1920x1080.

GG

Depending on the graphics card, DOS mode may
not work if an HDMI to DVI Cable is in use.

GG

In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or bright­ness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.

GG

Avoid keeping a fixed image on the screen for a

long period of time. The fixed image may become
permanently imprinted on the screen.

GG

Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.

GG

If the screen is truncated using HDMI-PC
1920x1080, try changing the aspect ratio to

JJuusstt

sscc aann

.

GG

When selecting HDMI-PC, set the “Input Label ­PC” in the OPTION menu.

EXTERNAL EQUIPMENT SETUP

28

EXTERNAL EQUIPMENT SETUP

Screen Setup for PC mode

Selecting Resolution

You can choose the resolution in RGB-PC mode.
The

PPoossiittiioonn, PPhhaassee

, and

SSiizzee

can also be adjusted.

Select

PPIICCTTUU RREE

.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

Select

RReessoolluuttiioo nn

.

Select the desired resolution.

1024 x 768
1280 x 768
1360 x 768

Auto Config.

Resolution

Position

Size

Phase

Reset

SCREEN

Move

Prev.

1

MENU

3

4

2

ENTER

ENTER

ENTER

5

ENTER

Enter

Move

PICTURE

E

RG

• Brightness 50

• Sharpness 50

• Color 50

• Tint 0

• Advanced Control

• Picture Reset

Screen (RGB-PC)

LED Local Dimming :On

EXTERNAL EQUIPMENT SETUP

29

Auto Configure

Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

Select

AAuuttoo CCoonnffiigg..

.

Auto Config.

Resolution

Position

Size

Phase

Reset

SCREEN

Move

Prev.

To Set

3

2

ENTER

ENTER

Select

YY ee ss

.

4

ENTER

Start Auto Configuration.

5

ENTER

Select

PPIICCTTUU RREE

.

1

MENU

■

If the position of the image is still not
correct, try Auto adjustment again.

■

If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the

PP oo ssiittiioonn, SS ii zzee

or

PPhhaassee

.

Yes No

Enter

Move

PICTURE

E

RG

• Brightness 50

• Sharpness 50

• Color 50

• Tint 0

• Advanced Control

• Picture Reset

Screen (RGB-PC)

LED Local Dimming :On

EXTERNAL EQUIPMENT SETUP

30

EXTERNAL EQUIPMENT SETUP

Adjustment for screen Position, Size, and Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.

This feature operates only in RGB-PC mode.

Select

PPoo ssiittii oonn, SSiizzee

, or

PPhhaassee

.

Make appropriate adjustments.

Auto Config.

Resolution

Position

Size

Phase

Reset

GF

D

E

SCREEN

Move

Prev.

3

ENTER

4

ENTER

■

PPoo ssiittii oonn

: This function is to adjust pic­ture to left/right and up/down as you
prefer.

■

SSiizzee

: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.

■

PP hhaass ee

: This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.

Select

PPIICCTTUU RREE

.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

1

MENU

2

ENTER

5

ENTER

Enter

Move

PICTURE

E

RG

• Brightness 50

• Sharpness 50

• Color 50

• Tint 0

• Advanced Control

• Picture Reset

Screen (RGB-PC)

LED Local Dimming :On