LG 43LV640S INSTALLATION INSTRUCTIONS

INSTALLATION MANUAL

LED TV*

Please read this manual carefully before operating your
set and retain it for future reference.

LV640S-Z/T/G/D*
LU642H-G*

www.lg.com

2

TABLE OF CONTENTS

ENGLISH

TABLE OF CONTENTS

3 USING THE BUTTON

3 Basic functions

4 EZMANAGER

4 MODE SELECTION
5 LANGUAGE & COUNTRY SELECTION

6 INSTALLATION MENU

6 INTRODUCTION
7 LG HOTEL MODE
7 - Hotel Mode Operation
7 - Power On Status
8 - Volume
8 - Key Management
9 - Limited Mode
10 - DTV Programme Update
10 - Power On Default
11 - Aux Source Setting
11 - Power Management
11 - Radio Video Blank
11 - Factory Reset
12 NETWORK
12 - MAC Address
12 - Network Setting
13 - Wake On LAN
13 - Server Settings
14 GENERAL
14 - Configuration Setup
16 - External Speaker
16 - Set ID Setup
17 - Power Saving
17 - Password Change
17 - PreLoaded App
17 - Lock Mode
18 - Crestron
18 - Welcome Video
19 MEDIA SHARE
19 - Screen Share
19 - DIAL
19 - TV Name
19 - SoftAP
21 TV MANAGER
21 - USB Download Menu

29 IR CODES

30 EXTERNAL CONTROL DEVICE

SETUP

30 RS-232C Setup
30 Phone jack Type
30 Type of Connector : D-Sub 9-Pin Male
31 RS-232C Configurations
32 Command Reference List
33 IR OUT Using Guide
34 Transmission / Receiving Protocol

USING THE BUTTON

3

USING THE BUTTON

Basic functions

<A/B type>

ENGLISH

Power On (Press)

Power O1 (Press and hold)

Volume Control

Programmes Control

<C type>

Power On (Press)

Power O1 (Press and Hold)

Menu Control (Press2)

Menu Selection (Press and Hold3)

1 All running apps will close, and any recording in progress will stop.
2 You can access and adjust the menu by pressing the button when TV is on.
3 You can use the function when you access menu control.

4

EZMANAGER

ENGLISH

EZMANAGER

• Image shown may differ from your TV.

•

MODE SELECTION

(Depending on model)

-Please select the Mode for environment setting.

EZMANAGER

5

LANGUAGE & COUNTRY SELECTION

-Please select the Language and Country. Some countries need to select the Time Zone.

ENGLISH

6

INSTALLATION MENU

ENGLISH

INSTALLATION MENU

• Image shown may differ from your TV.

•

INTRODUCTION

The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’.
The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and
convenient operation for Hotelier and System Integrators.

TV

1 Press the Setting button for more than 5 seconds using the user remote control, programme

information will appear at top left on the screen.

2 Enter a four digit password and press ‘OK’ button.

- The TV is set with the initial password “1-1-0-5”.

3 Use the button to select the desired menu.

INSTALLATION MENU

7

LG HOTEL MODE

1 Use the button to select the LG HOTEL MODE SETUP.
2 Use the ‘OK’ button and then button to select Hotel Mode Operation.

-When ‘Hotel Mode Operation’ is set to On (Work), all functions of Hotel Mode apply.

Hotel Mode Operation

(Depending on model)

-Decide to work all functions of ‘Hotel Mode Operation’ or not by setting ‘Hotel Mode Operation’ as On(Work) or Off(Do Not
Work)

-When ‘Hotel Mode Operation’ is set to On(Work), all functions of Hotel Mode apply.

-When ‘Hotel Mode Operation’ is set to Off(Do Not Work), all functions of Hotel Mode Do Not apply.

-When it is set to ‘On’, all items reserved at the Schedule list are deleted and the reservation function is not supported.(applied
for the model offering the reservation function)

-The TV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately from the Hotel mode.

-When it is set to ‘On’, User Menu → General → ‘Reset to Initial Settings and Home/Store Mode’ are disabled.

-When ‘Hotel Mode Operation’ is set to On(Work), all skipped programs are not tuned by number keys.

-When ‘Hotel Mode Operation’ is set to On(Work), Detailed Information about the programme is not available in the EPG.

-When ‘Hotel Mode Operation’ is set to On(Work), User Menu -> Timer->’Auto Power Off’ is disabled.

-When ‘Hotel Mode Operation’ is set to On(Work), User Menu -> Timer->’2 Hour Auto Power Off’ is disabled.

ENGLISH

Power On Status

-Decide to select working status of TV Set when turn on main power.

-You can set with PWR, STD, LST.

-PWR always make TV set On status when turn on main power .

-STD make Stand-by status when turn on main power.

-LST make TVSet work like previous power status. As same concept as Power Backup mode; If main power were turned off
in Power On status, TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in
Stand-by status.

-If there Block All is both IR Operation and Local Key Operation from Key Management, In order to provide the Option
that must be able to turn on the TV in the TV turned off situation, change the value of the PWR. (Reference the Key
Management)

8

INSTALLATION MENU

ENGLISH

Volume

-Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’ as On(Work) or Off(Do Not
Work).

-(0 ≤ Min ≤ Start ≤ Max ≤ 100)

Start Volume

yThis entry sets the start volume level when is power on.

-The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)

-The default setting is ‘Off ’ (disabled).

-When enabled, if the value is lower then the minimum specified in the minimum volume entry, the minimum volume
entry must be used.

-When enabled, if the value is larger then the maximum specified in the maximum volume entry, the maximum volume
value must be used.

-Access to a volume in ‘On Timer’ must be fixed to start volume when ‘Hotel Mode Operation’ (On) and ‘Start Volume’ (Off, 0
~ 100) were set simultaneously.

Maximum Volume

yThis entry sets the maximum volume level the set. The level is specied as a number between ‘Minimum Volume’ to 100. (Min ≤

Max ≤ 100).

-If the command volume up to higher than maximum volume’ is received, that should be ignored.

-The default value is 100.

Minimum Volume

yThis entry sets the minimum volume level the set will produce.

-The level is specified as a number between 0 to ‘Maximum Volume’. (0 ≤ Min ≤ Max)

-If the command volume down to lower than minimum volume is received, that should be ignored.

-The default value is 0.

Key Management

-Manage key usability of Local(Front) Key and Remote Control. When selected to ‘On’, following ‘IR Operation’ and ‘Local Key
Operation’ will be worked by below.

IR Operation

yDecide whether work the LG remote control or not.

-When ‘IR Operation’ is set to 'Normal', all remote keys are available.

-'Use PWR Only' makes block all remote keys except power key.

-When ‘IR Operation’ is set to 'Block All', all normal remote keys don’t work.

Local Key Operation

yDecide to operate 'Local/Front Key' working behavior by setting ‘Local Key Operation’ as 'Normal', 'Use PWR Only' and 'Block All'.

-When ‘Local Key Operation’ is set to 'Normal', all local keys are available.

-'Use PWR Only' makes block all local keys except power key.

-When ‘Local Key Operation’ is set to 'Block All', all local keys don’t work.

INSTALLATION MENU

9

Limited Mode

-Configure TV function’s limitation. When selected to ‘On’, following sub-menus will be worked by below.

Setup Menu

-Permit to tune and manage programmes as 'On'(permitted) or 'Off'(not permitted).

Programme Change

yDecide to change channel or not by setting ‘Program Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present

source is TV.

-When ‘Programme Change' is set to Off (Change Impossible)
» Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu' in the Main Menu OSD is

impossible.
» ‘Programme' item in 'On Time' menu will be fixed.
» Entering 'Programmes' in the 'Main Menu’ OSD is impossible regardless of 'Programmes' item.

-When 'Program Change’ is set to On(Change Possible), ‘Program Key’, ‘Numeric Key’, ‘List Key’, ‘Q.View’ Key, 'TV/RAD Key',
does work and entering ‘Channel Menu' in the Main Menu OSD is possible.

Menu Display

yFunction to decide whether work with menu (including relevant menus too) of control key (On – Enter possible) or not (O – Enter

Impossible).

-Although select Off(Enter impossible), the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ is
available.

-When select On(Enter possible), Menu works.

OSD Display

yDecide to display OSD or not by setting ‘OSD Display’ as On(Display) or O(Do not Display).

-When ‘OSD Display’ is set to ‘Off’(Do not Display), all OSD is not displayed except some exception.

-Although select ‘Off’ (Do not Display), the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ and
entering service menu are available. (In-Start, Power-Only, Adjust, Installation Menu…)

ENGLISH

System Provider Mode

y‘System Provider Mode’ allows access to the menu system from the front panel or remote control but access is controlled as follows:

-When value is ‘On’, Accessible Items on the menu system, others are not permissible.
» Input select screens
» Sleep timer
» Aspect Ratio
» Subtitles
» Programmes (Except for Programme Tuning & Settings and Programme Manager)
» ‘Safety’ / 'Photo & Video' / 'Music' / ‘Network’ / ‘Bluetooth’ Menu

-If the channel map is empty, ‘Auto-tuning’ guide dialog should be blocked by pressing ‘List’, ‘CH+’, ‘CH-’ keys.

10

INSTALLATION MENU

ENGLISH

DTV Programme Update

-It is a mode to set whether to update dtv Programme automatically or not.

-When DTV Programme Update is set to ‘Auto’, the func tion to update TV’s programme map according to dtv programme’s
stream information.

-DTV Programme Update is set to ‘Manual’, the func tion to keep TV’s programme map even though dtv programme’s
information is changed.

Power On Default

-Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by status.

-Set to On(Work) or Off(Do Not Work).

-When ‘Power On Default’ is set to Off, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio
menu.

-When Power On Default is set to On, it can set by entering the subordinate menu.

Input

-Set whether it is turned on by the set input source or by the last stored input source.

Programme

-Select start channel number if Input source’s value is TV.

A/V Setting

-If ‘A/V Setting’ is changed from ‘Off ’ to ‘On’, A/V parameters that are set before entering ‘Installation Menu’ are applied
whenever turn on power.

Aspect Ratio

-The aspect ratio determines the default aspect ratio that the set returns to on power up.

INSTALLATION MENU

11

Aux Source Setting

-Set to On(Work) or Off(Do Not Work).

-The Auxiliary (Input) Source Setting feature will enable or disable for each external input.

-User cannot disable the current input’s ‘Aux Source Setting’.

Power Management

yThe Power Management feature will turn o the television receiver if no input control command is received from either the Local

or IR Key within a selected hours.

-Activity on either of these inputs shall reset the ‘Power Management’ timer and prevent interruption of TV viewing.

-This entry can be set to a value which is corresponding to the desired hours (1Hour to 7Hours).

-Default value is ‘Off(disabled)’.

Radio Video Blank

-Set to On(Work) or Off(Do Not Work).

-Programme that is set to ‘Radio Programme’ and only has Sound should decide whether to set ‘Video Blank’ or not.

-When ‘Radio Video Blank’ is set to On(Work), ‘Video Blank’ works only in case of Radio Programme.

- Although set to On( Work), if there are Video signal, ‘Video Blank’ wouldn’t work. In consideration of case that display
background screen and broadcast only with Radio, ‘Video Blank ’works only when there is no Video signal.

-When set to Off(Do Not Work), ‘Video Blank’ do not work although it is the Radio Programme.

-This operates only in the Analog TV Mode.

Factory Reset

-Change all settings to their default values.

ENGLISH

12

INSTALLATION MENU

ENGLISH

NETWORK

1 Use the button to select the NET WORK.

MAC Address

-Displays the MAC address (not customizable).

Network Setting

One-click network connection

-Connects easily to a wired/wireless network.

-Network Connection to connect to an available network automatically. Follow the prompts on the TV.

To connect to a network through Set Expert

- For use in special circumstances such as in offices (in cases where a static IP is used).

1 Select a network connection, either Wired or Wireless.
2 When connecting via Wired, Congures the IP settings of the TV set. You can set the IP address, subnet mask, gateway and

DNS server.

3 When connecting via Wi-Fi, use the one of the following network connection methods.

AP List Connects to the network selected from the AP List.

Enter the SSID Connects to the wireless AP typed in.

WPS-PBC Connects easily when the button of a wireless AP supporting PBC is pressed.

WPS-PIN Connects easily when the PIN of the wireless AP that you wish to connect to is entered in to the AP website.

Advanced Wi-Fi Settings After connects Wi-Fi, you can set the IP address, subnet mask, gateway and DNS server.