LG 42PX5D-UB, 42PX4D, 42PX4D-UB User Manual

Download

Page 1

Page 2

2 Plasma TV

Warning/Caution

WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-800-243-0000 http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

/CAUTION

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

arning/Caution

Page 3

Owner’s Manual 3

TV Guide On Screen Notices for U.S.A.

In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or

one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by

Gemstar-TV Guide International, Inc.

The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895,

6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.

The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its

affiliates.

Digital Cable Compatibility

This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by

direct connection to a cable system providing such programming. A security card provided by your cable operator is required

to view encrypted digital programming. Cable operator enhanced program (For example, electronic program guide provided

by the cable operator), and data enhanced television service may require the use of a set top box. For more information con-

tact your local cable operator.

Use of the CableCARD

TradeMark.

“CableCARD

is a trademark of Cable Television Laboratories, Inc.”

Trademark Notice

Aux Etats Unis TV GUIDE et d’autres marques relatives sont des marques déposées de Gemstar-TV Guide International,

Inc. et/ou d’une de ses sociétés affiliées. Au Canada TV GUIDE est une marque déposée de Transcontinental Inc., utilisée

sous licence de Gemstar-TV Guide International, Inc.

Le système TV Guide On Screen est fabriqués sous licence de Gemstar-TV Guide International, Inc. et/ou d’une de ses sociétés

affiliées.

Le système TV Guide On Screen est protégés par un ou plusieurs brevets émis aux Etats Unis, comme le 6,498,895,

6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.

License Notice

Patent Notice

Page 4

4 Plasma TV

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Safety Instructions

PORTABLE CART WARNING

Page 5

Owner’s Manual 5

Safety Instructions

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that

is, a single outlet circuit which powers only that appliance and has no

additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power cords, or damaged or

cracked wire insulation are dangerous. Any of these conditions could

result in electric shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the

cord exits the appliance.

16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

17. Wet Location Marking :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall

be placed on the apparatus.

Page 6

6 Plasma TV

Contents

After reading this manual, keep it handy for future reference.

Warning/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Digital Cable Compatibility . . . . . . . . . . . . . . . . . . . . . . . . .3

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4~5

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Connection Options . . . . . . . . . . . . . . . . . . . . . .9

Remote Control Key Functions . . . . . . . . . . 10~11

Installation

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Installation Instructions . . . . . . . . . . . . . . . . . .12~13

Joining the TV assembly to the wall to protect the set tum-

bling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Swivel function . . . . . . . . . . . . . . . . . . . . . . . . . . 13

External Equipment Connections . . . . . . . . . .14~19

Antenna or Cable Connection . . . . . . . . . . .14~15

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .15

External A/V Source Setup . . . . . . . . . . . . . . . .16

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

CableCARD

Setup . . . . . . . . . . . . . . . . . . . . .17

HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . .17

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .19

Digital Audio Output . . . . . . . . . . . . . . . . . . . . .19

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20~22

TV Guide On Screen Setup . . . . . . . . . . . . . .23~32

IEEE 1394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33~40

TV Guide On ScreenTMSystem . . . . . . . . . . . . .41~59

Operation

Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .60

TV Setup

On-screen Menus Language Selection . . . . . . .61

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .62

Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .62

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .63

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .63

Channel Label Setup . . . . . . . . . . . . . . . . . . . .64

Main Picture Source Selection . . . . . . . . . . . . .64

Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Manual Picture Control (Custom Option) . . . . . .65

Color Temperature Control . . . . . . . . . . . . . . . .65

Video Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .66

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .66

Manual Sound Control (Custom Option) . . . . . .66

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .67

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .67

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . .68

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .69

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .69

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .69

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .70

Option Menu Features

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .71

Cinema 3:2 Mode Setup . . . . . . . . . . . . . . . . . .71

Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Caption / Text . . . . . . . . . . . . . . . . . . . . . . . . . .72

Caption Option . . . . . . . . . . . . . . . . . . . . . . . .73

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Auto Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Lock Menu Options

Lock Menu Options . . . . . . . . . . . . . . . . . . . . . .76

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .77

CableCARD

Function

Cable menu options . . . . . . . . . . . . . . . . . . . . .78

Scrambled channel . . . . . . . . . . . . . . . . . . . . . .78

Cable Channel List . . . . . . . . . . . . . . . . . . . . . .79

Emergency Alert Message . . . . . . . . . . . . . . . .79

. . . . . . . . . . . . . . . . . . . . . . . . . .80~85

Remote Control

PIP (Picture-in-Picture)/POP/Twin Picture . . . . . . .86

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..86

Selecting an Input Signal Source for PIP/Twin Picture

. .86

Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .86

TV Program Selection for PIP . . . . . . . . . . . . . .86

Moving the PIP sub picture . . . . . . . . . . . . . . . .87

Adjusting Main and Sub Picture Sizes for Twin Picture . .87

POP(Picture-out-of-Picture: Channel Scan) . . . .87

APM(Adaptive Picture Mode) . . . . . . . . . . . . . . . .88

Brief Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

Freeze & Magnify . . . . . . . . . . . . . . . . . . . . . . . . .90

Screen Setup for PC mode . . . . . . . . . . . . . . . . . .91

External Control Device Setup . . . . . . . . . . . . . . . .92~97

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98~99

Programming the Remote . . . . . . . . . . . . . . . . . . . . .100

Programming Codes . . . . . . . . . . . . . . . . . . . . .101~102

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . .103

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . .105

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107~108

Contents

Setup and Operation Checklist

Setup and Operation Checklist (See pages 14~19 for available connection and operational setup options.)

1. Unpack TV and all accessories.

2. Connect all external video and audio equipment. see pages 15~19.

3 Install batteries in remote control.

See page 11.

4. Turn TV on. See page 60.

5. Turn video source equipment on.

6. Select viewing source for TV. See pages 64.

7. Fine-tune source image and sound to your personal preference or as required by source. See pages 65~ 68.

8. Additional features set up See Contents above.

Page 7

Owner’s Manual 7

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of these mean that you get perfect images that are easily viewable in a display that is less than 5 inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product, is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.

Page 8

8 Plasma TV

Introduction

TV GUIDE

- This is a simplified representation of a front panel.

- Here shown may be somewhat different from your TV.

MENU Button

TV/VIDEO Button

VOLUME (FF,G) Buttons

CHANNEL (E, D) Buttons

INDEX

Switches LED Display on or off.

TV GUIDE Button

Remote Control

Sensor

Power Standby Indicator

Illuminates orange in

standby mode.

When the TV is turned on,

the indicator will blink

green for 3-4 seconds

before the picture is seen.

POWER Button

Controls

Front Panel Controls

42PX5D

42PX4D

Page 9

Page 10

10 Plasma TV

Installation

- When using the remote control, aim it at the remote control sensor on the TV.

MODE

DAY -

DAY +

FLASHBK

APM

1394

FREEZE

TV INPUT

TV/VIDEO

M/C EJECT

AUTO DEMO

XIT

MUTE

Switches the sound on or off.

(Refer to p.90)

MODE

Selects the remote operating mode: TV,

DVD, VCR, AUDIO, CABLE or STB. Select

a mode other than TV, for the remote to

operate an external device.

FLASHBK

Tunes to the recent channels.

EXIT

Clears all on-screen displays and returns to

TV viewing from any menu.

TIMER

Lets you select the amount of time before

your TV turns itself off automatically.

Brings up the main menu to the screen.

Enters or exits a Panel Menu in the TV Guide

On Screen system.

PIP

Switches to PIP, POP (Picture-out-ofPicture) and Twin picture modes in regular sequence. Switches the video window locking or unlocking in the Listings Grid.

PIPCH-/PIPCH+

Changes to the next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture in PIP/Twin picture mode.

SWAP

Exchanges the main/sub images in PIP/Twin picture mode.

EZ PIC

Selects a factory preset picture mode

depending on the viewing environment.

ADJUST

Adjusts screen position, size, and phase in

PC mode.

FREEZE

Freezes the currently-viewed picture. Main

picture is frozen in PIP/Twin picture mode.

TV/VIDEO

External input modes rotate in regular sequence: Antenna, Cable, Video, Front Video, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI and HDMI2 input sources. (Video, Front Video, Component 1-2 input sources are linked automatically, only if these are connected )

POWER

Turns your TV or any other programmed

equipment on or off, depending on mode.

TV GUIDE

Brings up the TV Guide On Screen system to the screen.

Mark

Selects a photo or music you want to view or play in Xstudio mode.

LIGHT

Illuminates the remote control

buttons of selected mode.

FAV

Scrolls the Favorite channels.

AUTO DEMO

Starts the demonstration to explain the main

features of this TV.

Remote Control Key Functions

Page 11

Owner’s Manual 11

Installation

DAY+/DAY-

Moves the Listings Grid forward or backward in 24 hour increments.

MODE

DAY -

DAY +

FLASHBK

APM

1394

FREEZE

TV INPUT

TV/VIDEO

M/C EJECT

AUTO DEMO

NUMBER buttons

/VCR/DVD control buttons

• Use for Photo mode or Music mode of .(Refer to p.83, 85)

• Controls the DVHS or Camcorder in

• IEEE 1394 mode.

• Controls some video cassette ••••

• recorders or DVD players when you

• have already selected DVD or VCR

• mode button.

RATIO

Changes the aspect ratio.

Select a closed caption:

Off, CC1~4, Text1~4.

THUMBSTICK (Up/Down/Left/Right/ENTER)

Allows you to navigate the on-screen menus

and adjust the system settings to your pref-

erence.

CHANNEL UP/DOWN

Selects available channels found during Manual scan.

PAGE UP/PAGE DOWN

Moves from one full set of screen information to the next one.

SAP

Selects MTS sound: Mono, Stereo, and

SAP in Analog mode. Change the audio lan-

guage in DTV mode.

EZ SOUND

Selects the sound appropriate for the program's character.

APM (Adaptive Picture Mode)

Concurrently, compare with the Daylight, Normal, Night Time and Custom on the screen. (Refer to p.88)

VOLUME UP/DOWN

Increases/decreases the sound level.

INFO

Channel information is displayed on top of the screen. But not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.

Page 12

12 Plasma TV

Installation

Owner’s Manual

1.5V

Batteries

Power Cord

MOD

FLASHBK

APM

AUTO DEMO

M/C EJECT

TV INPUT

TV/VIDEO

75Ω Round Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

• If the set will be mounted on a desk top, insert the 2 eye-bolts and tighten them securely in the upper holes as shown. Install the wall brackets on the wall with 2 bolts*, (not supplied with the product), as shown. Match the height of the eye-bolts and the wall brackets. Check to be sure the eye-bolts and the brackets are tightened securely.

• Secure the TV assembly to the wall with strong strings or wire cables, (not supplied with the product), as shown.

2-Wall brackets

2-eye-bolts

Page 13

Owner’s Manual 13

Installation

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

4 inches

2 inches

4 inches4 inches

Page 14

14 Plasma TV

Installation

Antenna or Cable Connection

1. Analog and Digital TV signals provided on antenna

External Equipment Connections

- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection

- For optimum picture quality, adjust antenna direction if needed.

2. Analog and Digital TV signals provided on cable

CABLE

Page 15

Owner’s Manual 15

Installation

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

Connection Option 1

Set VCR output switch to channel 3 or 4 and

then tune the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as

shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

3. Select the input source with using the TV/VIDEO button on the remote control. Note that this TV finds the connected input sources automatically for Video, Front Video and Component 1-2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected.

Do not connect to both Video and S-Video at the same time.

VCR Setup

AUDIO

PTICAL)

RGB INPUT

VIDEO

COMPONENT INPUT 1

(MONO)

CABLE

ANTENNA

DVD /DTV INPUT

COMPONENT INPUT 2

MONITOR OUTPUT

A/V INPUT

VIDEO

AUDIO

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

AUDIO INPUT

S-VIDEO

REMOTE CONTROL

AC INPUT

VCR Rear

• To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA

Signal

Amplifier

Page 16

16 Plasma TV

Installation

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

How to connect

Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Select the input source with using the TV/VIDEO button on

the remote control. Note that this TV finds the connected input sources automatically for Video, Front Video and Component 1-2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected.

2. Operate the corresponding external equipment. For connection instructions to operate the TV Guide On Screen system, see page 23~24.

Component ports

on the TV

Video output ports on DVD player

Y Y Y Y

B-Y

Cb PB

R-Y

Cr P

How to connect

1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

Note: If your DVD player does not provide component video output, use S-Video output.

How to use

1. Turn on the DVD player and then insert a DVD.

2. Use the TV/VIDEO button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video or Front Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

A/V Source Setup

DVD Setup

RS-232C INPUT

(CONTROL/SERVICE)

AUDIO

DIGITAL AUDIO

(OPTICAL)

DVI INPUT

COMPONENT2 INPUT

OUTPUT

RGB INPUT

VIDEO

HDMI 2

Page 17

Owner’s Manual 17

Installation

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV’s COMPONENT (Y, P

B, PR) INPUT, RGB, HDMI1/DVI or

HDMI2 jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use TV/VIDEO on the remote control to select Component 1, Component 2, RGB-DTV, or HDMI1/DVI, HDMI2 source.

HDSTB Setup

RS-232C INPUT

(CONTROL/SERVICE)

AUDIO

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT2

INPUT

OUTPUT

RGB INPUT

VIDEO

HDMI 2

HDMI1 /DVI

Page 18

18 Plasma TV

How to connect

1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product).

If you do not need to connect audio, HDMI2 port is also available for the DVI video connection.

2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI-

TAL AUDIO(OPTICAL) port for DVI INPUT.

3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT

port located on the right side of RGB INPUT port.

How To Use

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.64)

TV/VIDEO button is also available for this purpose.

3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC

mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the

brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be

changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

How to connect

1. Connect the PC to RGB INPUT port of this TV with a RGB cable(not supplied with this product).

2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT

port located on the right side of RGB INPUT port.

How To Use

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz.

2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.64)

Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose.

3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC

mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the

brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be

changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

720x400

Installation

PC Setup

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.

800x600

70.08

85.03

59.94

72.80

75.00

85.00

35.156

37.879

48.077

46.875

53.674

48.363

56.476

60.023

56.25

60.31

72.18

75.00

85.06

60.00

70.06

75.02

Vertical

Frequency(Hz)

Resolution

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1024x768

Resolution

640x480

Horizontal

Frequency(KHz)

31.469

37.927

31.469

37.861

37.500

43.269

Monitor Display Specifications (RGB-PC )

Page 19

Owner’s Manual 19

Installation

Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.

2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.

See the external audio equipment instruction manual for operation.

Note: When connecting with external audio equipments, such as

amplifers or speakers, please turn the TV speakers off.(Refer to p.67)

Caution: Do not look into the optical output port.

Looking at the laser beam may damage your vision.

Digital

Audio Output

RS-232C INPUT

(CONTROL/SERVICE)

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT2 INPUT

OUTPUT

RGB INPUT

HDMI 2

HDMI1 /DVI

DVD /DTV INPU

IEEE-1394

AUDIO INPUT

Cable

The TV has a special signal output capability which allows you to hook up the second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding the device’s input settings.

Notes:

• Component 1-2, RGB-PC/RGB-DTV, HDMI1/DVI,HDMI2, DTV input sources cannot be used for Monitor out.

• When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.(Refer to p.67)

• We recommend to use the video and audio output jacks for VCR recording.

AUDIO

AUDIO INPUT

RGB INPUT

VIDEO

COMPONENT INPUT 1

(MONO)

CABLE

ANTENNA

Page 20

20 Plasma TV

Installation

- HDMITM, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing.

- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolution.

- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz.

- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio.

- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

How To Connect

1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI or HDMI2 input source in main input option on the SETUP menu.(Refer to P.64)

TV/VIDEO button is also available for this purpose.

How To Connect

1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio.

2. A separated audio connection is necessary.

3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT.

4. Connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port.

How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI input source in main input option on the SETUP menu.(Refer to P.64)

TV/VIDEO button is also available for this purpose.

HDMI

Page 21

Owner’s Manual 21

Installation

Cable sample

HDMI Cable (not supplied with the product)

HDMI to DVI Cable (not supplied with the product)

Fiber Optic Digital Audio Cable (not supplied with the product)

Analog Audio Cable(RCA type) (not supplied with the product)

Analog Audio Cable(Stereo to RCA type) (not supplied with the product)

Reference

Page 22

22 Plasma TV

Installation

How to use

1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET.

2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control.

3. Select HDMI1/DVI Input source in Main Input option on the SETUP menu.(Refer to P.64)

4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

- Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

- Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter feature on the ISM Method menu.

- When Source Devices connected with HDMI1/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit to Screen. As shown the picture below, press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center.

- When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution(480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

- In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

POSITION G

SIZE

PHASE

RESET

Adjust

In This Mode, the Supported TV SET Resolution Specification

- 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

- 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

- 720 x 480 P @ 59.94Hz / 60Hz, 16:9

- 720 x 480 P @ 59.94Hz / 60Hz, 4:3

In This Mode, the Supported PC Resolution Specification

- 640 x 480 @ 60Hz

- 640 x 480 @ 72Hz

- 640 x 480 @ 75Hz

- 800 x 600 @ 56Hz

- 800 x 600 @ 60Hz

- 800 x 600 @ 72Hz

- 800 x 600 @ 75Hz

- 1024 x 768 @ 60Hz(preferred format)

- 1024 x 768 @ 70Hz

- 1024 x 768 @ 75Hz

PC mode

Page 23

Owner’s Manual 23

Installation

- The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your area—which are updated several times a day.

- Once you set up the TV according to manufacturer’s instructions, you are ready to set up the TV Guide On Screen system.

- To download program listings the TV Guide On Screen system needs to be able to change channels on your cable box when the TV is not in use. Please connect the supplied G-LINK cable to the G-LINK jack of the TV. After you connect the G-LINK cable you will be able to control your cable box using the TV’s remote.

Notes:

• The TV Guide On Screen system provides listings for cable-ready, cable box, and digital cable services as well as over-the-air broadcast. It does not provide listings for satellite services.

• You may use to connect directly without Cable Box.

RS-232C INPUT

(CONTROL/SERVICE)

DIGITAL AUDIO

(OPTICAL)

DVI INPUT

COMPONENT2

INPUT

OUTPUT

RGB INPUT

HDMI 2

HDMI /DVI

Page 24

24 Plasma TV

Installation

AUDIO

VIDEO

COMPONENT INPUT 1

(MONO)

Page 25

Owner’s Manual 25

Installation

Note:

• The G-LINK

cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page

23~24 for G-LINK

connection instructions.

The TV Guide On Screen system's Welcome Screen appears:

-- by pressing the TV Guide key

-- when you power On your TV if you previously skipped "Set up TV Guide On Screen now" on the Reminder Screen.

The Welcome Screen highlights features of the TV Guide On Screen system.

Press ENTER to begin Setup.

How to use

1. Screen 1: Country

• This screen asks you the location of your TV.

• Use the

D/E

button to highlight a country.

• Press ENTER to display Screen 2.

The TV Guide On Screen system's Reminder Screen appears:

-- after initial TV set up

-- if you power Off the TV and then power it back On

To make a selection, use the

D / E

button to highlight an option,

and press ENTER.

• "Set up TV Guide On Screen now," displays the Welcome Screen. Press ENTER to begin Setup.

• "Remind me to set up later" returns you to watching TV.

• "Don't remind me again" returns you to watching TV and stops the reminder screen from appearing upon power On.

2.Reminder Screen

1.Welcome Screen

TV Guide On Screen Setup

Page 26

26 Plasma TV

Installation

2. Screen 2: Enter ZIP or Postal Code

Option 1

• If you selected USA in Screen 1, you see the ZIP Code screen.

• You input numbers by either pressing the number keys on the remote

or using the

D/E

button to display a number, and then the F / G but-

ton to move to another field.

• Press ENTER to display Screen 3.

Option 2

• If you selected Canada in Screen 1, you see the Postal Code screen.

• You input characters by using the

D/E

button, and then the F / G

button to move to another field.

• Press ENTER to display Screen 3.

3. Screen 3: Do you have Cable Service connected?

• If you select Yes, you see Screen 4.

• If you select No, you see Screen 12.

4. Screen 4: Do you have a Cable Box?

• If you select Yes, you see Screen 5.

• If you select No, you see Screen 12.

Page 27

Owner’s Manual 27

Installation

6. Screen 6: Cable Box Tuning Channel

• Select the channel used for the cable box.

• Press ENTER to display Screen 7.

7. Screen 7: Cable Box Configuration Diagram

• The diagram shows the correct way to install the G-LINK Cable from the back of the device to the cable box.

Make sure the G-LINK

Cable is properly installed.

• Press ENTER to display Screen 8.

5. Screen 5: Which TV input is the cable box plugged into?

• If you select Cable, you see Screen 6.

• If you make any other choice, you see Screen 7 .

Page 28

28 Plasma TV

Installation

8. Screen 8: Cable Box Brand Name

• Use the

D/E

button to select a cable box brand.

• Press ENTER to display Screen 9.

9. Screen 9: Cable Box Preparation

• Follow the on-screen instructions, and press ENTER to display

Screen 10.

10. Screen 10: Cable Box Code Testing

• When testing is done, Screen 11 displays automatically.

11. Screen 11: Cable Box Tuned to Channel 9?

• If you select Yes, you see Screen 12.

• If you select No, a different code is tested in Screen 10.

Note:

• Many Cable Boxes require testing more than one code.

• If you select Test this code again, the same code is tested again in Screen 10.

Page 29

Owner’s Manual 29

Installation

14. Screen 14: Congratulations

• Press ENTER to display Screen 15.

13. Screen 13: Are your basic settings correct?

• If you select Yes, you see Screen 14.

• If you select No, you see Screen 1.

12. Screen 12: Do you have an antenna connected?

• If you select Yes, you see Screen 13.

Note:

• If you selected No in Screen 3 then you must select Yes in this screen to receive a channel lineup and listings.

• If you select No, you see Screen 13.

Page 30

30 Plasma TV

Installation

17. Screen 17: VCR Brand Name

• Use the

D/E

button to select the brand of the recording device.

• Press ENTER, and you see Screen 18.

16. Screen 16: VCR Configuration Diagram

• This screen shows the correct way to install the G-LINKTMCable from the back of the TV to the Recording device.

Make sure the G-LINK

Cable is properly installed.

• Press ENTER, and you see Screen 17.

15. Screen 15: Is a VCR Connected?

• If you select Yes, you see Screen 16.

• If you select No, you see Screen 21.

Page 31

Owner’s Manual 31

Installation

18. Screen 18: VCR Preparation

• Follow the on-screen instructions, and press ENTER to display Screen 19.

19. Screen 19: VCR Code Testing

• When testing is done, Screen 20 displays automatically.

20. Screen 20: VCR Tuned to Channel 9?

• If you select Yes, you see Screen 21.

• If you select No, a different code is tested in Screen 19.

Notes :

• Many VCRs require testing more than one code.

• If you select Test this code again, the same code is tested again in Screen 19.

Page 32

32 Plasma TV

Installation

21. Screen 21: Confirming Your Settings

• Verify the Setup information is correct.

• If it is, select Yes, end setup, and you see Screen 22.

• If it is not, select No, repeat setup process, and you see Screen 1.

22. Screen 22: Congratulations

• You have successfully completed Setup!

• Press ENTER and you see Screen 23.

23. Screen 23: Helpful Information

• This screen tells you valuable information on using your TV Guide On Screen system .

• Press ENTER to watch TV.

Notes:

• The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to receive regular program listings, please remember to do the following:

1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.)

2. If you have a Cable box connected, leave the cable box On, but turn the TV Off.

3. If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.)

4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, please follow the on-screen instructions.

• Program listings are updated several times a day. It may take up to 24 hours to begin to receive any TV program listings. It may take up to one week to receive all eight days of TV program listings.

Page 33

Owner’s Manual 33

Operation

- It's available to communicate to either direction and you can give and take a image, sound, or each control command with one cable.

How to connect the 1394

•To operate the IEEE1394, these methods are available as shown below.

1. When connecting the DVHS or the MicroMV Camcorder, as shown in the (a) or (b) figure, press the button to show the control panel.

IEEE 1394 Functions

1394

Note: When connecting the DVHS and the MicroMV Camcorder, in case of showing ‘input error’ on the

MicroMV Camcorder window, it’s okay.

(a) TV DVHS

(b) TV MicroMV Camcorder

<TV>

<DVHS>

Page 34

34 Plasma TV

Operation

IEEE 1394 Functions

-When connecting the 1394 and then playing, you must use the original DVHS tape. If not, it may occur errors.

-If the operation normally doesn’t work on Daisy Chain connection, please change an arrangement of connected device.

2. When connecting the DVHS and the MicroMV Camcorder, as shown in the (c) or (d) figure, press the button to show the control panel and then select the DVHS or the MicroMV Camcorder.

1394

<TV>

<DVHS>

(d) Daisy Chain Connection

<TV>

<DVHS>

<Connect the

IEEE1394 Cable>

<Connect the

IEEE1394 Cable>

Page 35

Owner’s Manual 35

Operation

DVHS

How to play the DVHS

<TV>

<DVHS>

1. Connect the IEEE 1394 jack at the TV to the IEEE 1394 jack at the DVHS with IEEE 1394 Cable.

2. When watching the TV, press the button.

1394

• The control panel of DVHS

-Depending on the connected equipment, marked control panel may be different.

3 4

• Show the control panel of DVHS.

1. DVHS Model

2. Connected Equipment to the 1394

3. DVHS Company

4. DVHS Operating Status

5. Power On/Off

6. DVHS Play Time

7. Tape Status

• Tape shape Icon - Tape in or not

• Lock shape Icon - Writable or not

8. Initializing Play Time

9. DVHS Play, Pause, Stop, Search, Skip.

(Notes:

• Skip- This function is for a fast search. It searches the program’s start

Skip- point. On skipping, Search (

FFF,GG

), Pause ( II ) and Play (G) are dis

Skip- played on the Control Panel. In some models, it’s not available to Skip- operate the Skipping (

IFF,GGI ) function.

* Supported DVHS List

JVC(HM-DH40000K)

JVC(HM-DH40000U)

JVC(HM-DH5U)

MITSUBISHI(HV-HD1000)

PANASONIC(NV-DH2)

Notes:

• In case the DVHS have a incorrect recognition, the power cord of DVHS is completely pull out and then connect again.

• When searching the screen(

FF,GG

) , the DVHS may be strangely seen. And also the DVHS may late respond by devices.

Page 36

36 Plasma TV

Operation

IEEE 1394 Functions

Page 37

Owner’s Manual 37

Operation

• The control panel of MicroMV Camcorder

- Depending on the connected equipment, marked control panel may be --

- different.

1. MicroMV Camcorder Model

2. Connected Equipment to the 1394

3. MicroMV Camcorder Company

4. MicroMV Camcorder Operating Status

5. MicroMV Camcorder Play Time

6. Tape Status

• Tape shape Icon - Tape in or not

7. MicroMV Camcorder Play, Search, Pause or Stop

8. Initializing Play Time

7 8

Notes:

• In memory mode of MicroMV Camcorder , it doesn’t apply to connect

the IEEE1394.

• Regardless of a mode of MicroMV Camcorder, if the tape is ejected, it

doesn’t apply to connect the IEEE1394.

* Supported MicroMV Camcorder List

SONY DCR IP-1

SONY DCR IP-5

SONY DCR IP-45

SONY DCR IP-210

Page 38

38 Plasma TV

Operation

IEEE 1394 Functions

Page 39

Owner’s Manual 39

Operation

DTV Link

: DTV Link applies to 1394 connection of device labeled DTV Link logo.

How to play the DTV Link

1. Connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the DTV Link supported device IEEE 1394 Cable.

* What’s the DTV Link?

It is normal standard of CEA which restricts

by a remote and displays OSD and plays to

stream of a remote control by using a con-

nection of IEEE1394.

2. When watching the TV, press the .

1394

<TV>

3. Press the TV INPUT button to stop the IEEE1394

function.

Notes:

• On a condition of connecting the IEEE 1394, you can control the DTV Link device while watching the OSD through DTV and

DTV remote control.

( ex: change of channel, play, record, a show of recording list etc.)

• Analog channel is not supported.

• In case a device outputting MPEG2 TS Data through IEEE1394 port but it doesn't support to DTVLink, you are able to

see a screen even if it doesn't control directly on TV.

Page 40

40 Plasma TV

Operation

Don’t connect !

• When connecting with these 2 methods, the IEEE1394 will not work properly.

(a) LOOP Connection

<TV>

<DVHS>

<Connect the

IEEE1394 Cable>

(b) When connecting the 4 devices and over, the 1394 will not work properly.

Note: When the same devices connect with 2 devices and over, it’s undesirable.

IEEE 1394 Functions

Page 41

Owner’s Manual 41

Operation

TV Guide On Screen

System

Overview

- Your new TV contains the TV Guide On Screen Interactive Program Guide.

- The TV Guide On Screen system has features that help you get the most out of your viewing

experience.

TV Guide On Screen system Overview

The TV Guide On Screen system has the following features:

•Eight days of show listings (today plus seven days).

•Icons that indicate show rating, stereo, HDTV, new episode, etc.

•Intuitive up/down/left/right navigation using your remote control.

•Set shows to Record.

•Schedule show Reminders.

•Search shows by category (e.g., Movies, Sports, Children, etc.).

•Search for shows based on keywords or alphabetically by title.

•Direct tuning to a channel.

•Show information while watching TV.

•Streamlined System Setup and default setting options.

•Channel lineup customization.

•Help screens while in the TV Guide On Screen system.

Page 42

42 Plasma TV

Operation

TV Guide On Screen

System

•Video Window - displays TV video while the TV Guide On Screen system is displayed

•Service Bar - provides access to the 4 main Guide Services

•Current Service Label - indented to indicate current Service displayed

•Tile - displays show title

•Highlight - indicates an active tile

•INFO Box - provides information for a highlighted item

•INFO Button - indicates you can cycle through the various Info Box sizes

•Channel Logo - identifies network

•Record/Remind Icons - indicates a show is set to Record or set as a Reminder

•Panel Ad - location where show- or product-specific information appears (and also where Panel Menu appears)

Screen Components

- The screens displayed in the TV Guide On Screen system share many of the same compo-

nents, as shown in the following figure:

Page 43

Owner’s Manual 43

Operation

• A Panel Menu appears when the Menu key is pressed on a highlighted tile and additional options are available. It also

appears when you press ENTER on a show starting in the future.

• When a Panel Menu appears, the highlighted tile changes color to indicate the Panel Menu relates to this tile.

• The Panel Menu displays below the Video Window.

• Help is available for a displayed Panel Menu by pressing the INFO button.

• The

D / E

button move between the options within the Panel Menu.

• The left and right arrows move to adjacent options unless the highlight is on an odometer, where these arrows change the

odometer choice.

• Pressing ENTER from an odometer or number entry box moves the highlight to the default command button of that Panel

Menu, for example, Schedule Reminder.

• Pressing ENTER from a highlighted command button executes the action and closes the Panel Menu (e.g., Schedule

Reminder, Cancel).

• Select Cancel to cancel any changes and press ENTER to close this menu.

• Pressing Menu is a shortcut to Cancel. Press Menu to cancel any changes and close the menu.

• If a Panel Menu contains more menu options than can be displayed on a single screen,

D / E

button appear at the top or

bottom of a menu. Simply scroll down to access these options.

Panel Menu

Page 44

44 Plasma TV

Operation

TV Guide On Screen

System

- Access Listings by pressing the TV Guide button on your remote or on the front panel of your TV.

- Listings is always the first Service displayed in the TV Guide On Screen system.

- With Listings highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen.

•View 8 days of show listings

•Read show descriptions

•Tune directly to a show currently airing

•Set a show to Remind

•Set a show to Record

•Lock and unlock the Video Window

•Access Panel and Channel Ads

Use the

D / E

/ F / G

buttons to move the highlight

within Listings to:

Notes:

• There may be times when the TV Guide On Screen system could display partial or no program listings. The reasons for this include:

1. Program schedule information was not provided to TV

Guide On Screen.

2.The transmission of the program listings was interrupt-

ed.

3.The phrase “No Listings” will be replaced with program

information during the next transmission, which should

occur within the next 24 hours.

4.Please remember to turn off your TV when not in use in

order to receive program listings.

Main Services

Listings

Page 45

Owner’s Manual 45

Operation

- Search lets you find shows by category (Alphabetical, Movies, Sports, Children, Educational, News, Variety, Series, HDTV) or by

Keyword.

- With Search highlighted, press the INFO button to display a Help screen.

Press the INFO button again to close the screen.

•Category Search Example: Movies

1. From Search, use the Ebutton to highlight Movies.

Page 46

46 Plasma TV

Operation

TV Guide On Screen

System

2. Use the Ebutton to highlight a subcategory (for example, All).

3. Press ENTER to display a list of all Movies, organized by date

and time.

You can choose to set a recording, a reminder, or tune to the channel.

4. Highlight a show and press ENTER to watch (if on now) or

the Menu key to display the Episode Options menu.

Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar.

Tune to Channel - exits the TV Guide On Screen system

and tunes to the channel of the highlighted show (show

airs in the future).

Note: This option reads Watch Now if the show is cur-

rently airing.

Set Recording - displays the Record Options menu, from

which you can set frequency, start and end time, etc.

Set Reminder - displays the Remind Options menu, from

which you can set frequency, start time, automatically

power On, and auto-tune the TV.

Cancel - closes the menu, changes no information, and

returns to the highlighted show.

Page 47

Owner’s Manual 47

Operation

- Keyword search lets you enter a word(s) to look for a particular show by category or for every show title that matches.

• Keyword Search

1. Highlight the Keyword navigation label, and press

ENTER button to display the Keyword Search menu.

2. Highlight New Search, and press ENTER button.

3. The Search Options menu is displayed.

4. Highlight Category, and use the

F / G button to select

a category to search (e.g. All, HDTV, Children, Sports,

etc.). When finished, use the

button to highlight

Enter Keyword.

5. Highlight Enter Keyword, and press ENTER.

6. Use the

D / E

/ F / G

button to highlight a character,

and press ENTER to display it. When complete, high-

light Done and press ENTER.

Page 48

48 Plasma TV

Operation

TV Guide On Screen

System

The TV Guide On Screen system stores all the key-

words you create. To edit or delete a keyword, highlight

the keyword and press the Menu key. A Search Options

menu is displayed.

Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar.

Edit Search - displays the keyboard, where you can

change the keyword.

Delete Search - A Confirm menu is displayed.

•Yes - deletes the Search

• No - closes the panel menu

Cancel - closes the menu, changes no information, and

returns to the highlighted show.

7. A list of all matching shows for that keyword is dis-

played.

You can highlight a show, and press ENTER to dis-

play all airings. You can then highlight a specific list-

ing and press ENTER to watch (if On now) or the

Menu key to display the Episode Options menu.

From the Episode Options menu, choose to set a

recording, a reminder, or tune to the channel, as pre-

viously described.

Page 49

Owner’s Manual 49

Operation

- Schedule lets you review, edit, or delete Record and Remind events that you set previously.

- With Schedule highlighted, press the INFO button to display a Help screen. Press the INFO button again to close the

screen.

- An icon identifies the event type:

Record

W Once —records the show one time

W Regularly —records the show every time the show airs

on the same channel and starts at the same time

W Weekly —records the show each time the show airs on

the same day of the week, on the same channel and starts at

the same time

W Off —keeps the show in the list but will not record this

show until the frequency is changed.

Remind

W Once —sets a show reminder one time

W Regularly —sets a show reminder every time the

show airs on the same channel and starts at the same

time

W Weekly —sets a show reminder each time the

show airs on the same day of the week, on the same

channel and starts at the same time

W Off —keeps the show in the list but will not remind

until the frequency is changed

Highlight an event, and press the Menu key for options.

Go to Service Bar - closes the menu, changes no information, and returns to the Schedule Service Bar. Tune to channel - exits the TV Guide On Screen system and tunes to the highlighted show. Delete Recording - removes the recording from the Schedule, after a Confirm screen. Edit Recording - opens a menu from which you can change existing recording information. Set Reminder - opens a menu from which you can set a Reminder for the show (Record is not cancelled). Cancel - closes the menu, changes no information, and returns to the highlighted show.

Schedule

Page 50

50 Plasma TV

Operation

TV Guide On Screen

System

- After you initially complete Guide Setup, you can make changes to Guide settings in the following areas:

• Change System Settings

• Change Channel Display

• Change Default Options

Highlight a choice, press ENTER, and follow the on-screen instruc-

tions.

Page 51

Owner’s Manual 51

Operation

Press ENTER to display the Channel Editor screen.

Then, highlight a channel and press Menu. A Grid Options

menu is displayed.

Highlight Go Back to Setup to close the menu, change no

information, and return to the Setup Service Bar.

Or make changes and when finished, press ENTER to high-

light Done. Press ENTER again to close the menu and

accept the changes.

Highlight Cancel to close the menu, change no information,

and return to the highlighted channel.

• Change Channel Display

Change Channel Display lets you edit channel information

that appears in Listings. With Change Channel Display

you can :

• Change the position number to indicate where in the

Listings the channel displays

• Change the tune channel number

• Switch a channel

W On - the channel is always displayed

W Off - the channel is never displayed

W Auto-Hide - the channel is only displayed when

program information is available.

Page 52

52 Plasma TV

Operation

TV Guide On Screen

System

General Default Options lets you set defaults for the following:

•The initial Info Box size when the TV Guide On Screen system

is entered.

Choices are No, Small, Large, and Last Used

(Default = Last Used).

•The Info Box size rotation when the Info key is pressed while in

the TV Guide On Screen system.

Choices are No only, Small only, Large only, No & Small, No &

Large, Small & Large, All (Default = All)

•Automatic entry into the TV Guide On Screen system (Auto-

Guide) when the TV is powered On.

Choices are On and Off (Default = On).

Highlight General Default Options, and press the Menu key to dis-

play the General Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

When finished, press ENTER to highlight Done. Press ENTER

again to close the menu and accept the changes.

Highlight Cancel to close the menu, change no information, and

return to the highlighted option.

• Change Default Options

Change Default Options lets you change default settings in

the following categories:

• General Default Options

• Record Defaults

• Remind Defaults

Highlight Change Default Options, and press ENTER.

Page 53

Owner’s Manual 53

Operation

< Record Defaults>

• Record Default Options lets you set defaults for the following:

• When to start the record event. Choices are 120 minutes early to

120 minutes late, to On time. (Default = On time)

• When to end the record event. Choices are 120 minutes early to

120 minutes late, to On time. (Default = On time)

• Recorder choice: Please choose the VCR only. This TV does not

support other devices with a recording feature.

Highlight Record Defaults, and press the Menu key to display the

Record Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

< Remind Defaults>

Remind Default Options lets you set defaults for the following:

• Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No.

(Default = No)

• Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No.

(Default = No)

• When to display the reminder screen. Choices are 30 seconds to

15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early)

Highlight Remind Defaults, and press the Menu key to display the

Remind Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

When finished, press ENTER to highlight Done. Press ENTER

again to close the menu and accept the changes.

Highlight Cancel to close the menu, change no information, and

return to the highlighted option.

Page 54

54 Plasma TV

TV Guide On Screen

System

Operation

W Once —records the show one time

W Regularly —records the show every time the show

airs on the same channel and starts at the same time

W Weekly —records the show each time the show

airs on the same day of the week, on the same channel

and starts at the same time

W Off (not cancel) —keeps the show in the list but

will not record this show until the frequency is changed.

W Cancel (no icon displayed)—does not record

2) From a Panel Menu

• Highlight a show, and press Menu to display the Episode

Options menu.

• Highlight Set Recording, and press ENTER to display the

Record Options menu.

• Highlight the Frequency option, and use the left and right

arrows to choose among Once, Regularly, Weekly, and Off,

as previously described.

• Recorder choice: Please choose the VCR only. This TV does

not support other devices with a recording feature.

Note: Video Window Lock is switched to on or off using PIP

button in Listings mode.

You can set a show to Record in Listings, Search, and

Schedule or change Record settings for a show in Schedule.

There are 3 ways to set a show to Record:

1) Using the Record Button on the Remote

• Press the Record button on the remote to record the show

Once with current default settings (Start and End recording

On Time). Each time you press the Record button, you

change the record frequency (but not the default settings)

among Once (default), Regularly, Weekly, Off, and then

Cancel.

Note: The proper Record icon appears on the show tile, as

the Record button is pressed.

Record

Record And Remind Features

Page 55

Owner’s Manual 55

Operation

When finished, press ENTER to highlight Schedule Recording.

Press ENTER again to close the menu. You see a Record icon for

the selected frequency next to the show title.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

3) Manual Recording

• Highlight the Schedule Service label, and press Menu to display

the Schedule Options menu.

• Use the

D / E

/ F / G

buttons to move through the options. Use

the number or the

D / E

/ F / G

buttons to change the informa-

tion, as necessary.

• Highlight New Manual Recording and press ENTER to display

the Record Options menu.

• Current information (i.e., date, start and end times, channel,

input) is displayed.

• Recorder choice: Please choose the VCR only. This TV does

not support other devices with a recording feature.

Page 56

56 Plasma TV

Operation

TV Guide On Screen

System

• Use the left and right arrows to choose between Once, Daily,

Weekly, and Off, as follows.

W Once —records the time, channel, input, recorder

combination one time.

W Daily —records the time, channel, input, recorder

combination Monday through Friday.

W Weekly —records the time, channel, input, recorder

combination once a week on the selected day of the week.

W Off (not cancel) —keeps the time, channel, input, recorder

combination in the list without recording until the frequency is

changed.

Record Conflict

A conflict message appears for the following reasons:

• a show set to Record overlaps with any part of another show pre-

viously set to Record,

• a show set to Record overlaps with a show previously set to auto-

tune

Select one of these options:

W record anyway - this show will override an existing show set to

Record or auto-tune

W don't record this show - cancel the Recording

Before a recording begins, a notification screen appears

if your TV is On. At that time, you can choose to start or

cancel recording. If the TV is not On, the recording

occurs as scheduled. If there is no activity for 3 minutes,

the notification screen automatically closes and com-

pletes the highlighted item.

When finished, press ENTER to highlight Schedule

Recording.

Press ENTER again to close the menu. You see a

Record icon for the selected frequency next to the show

title.

Note: Manual recording is listed by channel number.

Highlight Cancel to close the menu, change no informa-

tion, and return to the highlighted show.

Page 57

Owner’s Manual 57

Operation

You can set a show Reminder in Listings, Search, and Schedule or

change Reminder settings for a show in Schedule.

There are 2 ways to set a show Reminder:

1) From a Panel Menu

• Highlight a show, and press Menu to display the Episode Options

menu.

• Highlight Set Reminder, and press ENTER to display the Remind

Options menu.

• Highlight the Frequency option, and use the left and right arrows

to choose between:

W Once —sets a show reminder one time

W Regularly —sets a show reminder every time the show

airs on the same channel and starts at the same time

W Weekly —sets a show reminder each time the show airs

on the same day of the week, on the same channel and starts

at the same time

W Off —keeps the show in the list but will not remind until

the frequency is changed

• Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No. (Default = No)

• Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No. (Default =

No)

• When to display the reminder screen. Choices are 30 seconds

to 15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early)

When finished, press ENTER to highlight Schedule Reminder.

Press ENTER again to close the menu. You see a Remind icon for

the selected frequency next to the show title.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

Remind

Page 58

58 Plasma TV

Operation

TV Guide On Screen

System

2) Manual Reminder

• Highlight the Schedule Service label, and press the Menu key to

display the Schedule Options menu.

• Use the

D / E

/ F / G

buttons to move through the options. Use

the number or

D / E

/ F / G

buttons to change the information, as

necessary.

• Highlight New Manual Reminder and press the ENTER key to dis-

play the Remind Options menu.

• Current information (i.e., date, start and end times, channel, input,

frequency, etc.) is displayed.

• Highlight the Frequency option, and use the

F / G buttons to

choose among Once, Daily, Weekly, and Off, as follows.

W Once —sets a show reminder for the time, channel, and

input combination one time

W Daily —reminds for the time, channel, and input combi-

nation Monday through Friday

W Weekly —sets a show reminder for the time, channel, and

input combination once a week on this selected day of the week

W Off (not cancel) —keeps the time, channel, input, destina-

tion combination in the list without reminding until the frequency

is changed

• Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No (Default =No).

• Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No (Default = No).

When finished, press ENTER to highlight Schedule Reminder.

Press ENTER again to close the menu. You see a Remind icon for

the selected frequency next to the show title.

Note: Manual reminder is listed by channel number.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

Page 59

Owner’s Manual 59

Operation

Based on your option settings, a notification screen will

appear, if your TV is On at the reminder time. You can

then choose to hide the reminder, or highlight the show,

and press ENTER to tune to the show. If there is no activ-

ity for 3 minutes, the notification screen automatically

closes and completes the highlighted item (hide

reminders).

If you choose Hide Reminders, the window closes for the

show or shows, but does not affect other Reminders you

set.

Note: If more than 2 reminders are set for the same time,

arrows appear on the Reminder screen. Use the

D/E

buttons to view the shows.

Remind Conflict

A conflict message appears for the following reasons:

• a show set with an Auto-Tune Reminder has the same

start time as an existing Auto-Tune Reminder.

• If you are using a cable box, a show set with an Auto-

Tune Reminder overlaps with a Recording already

scheduled.

Select one of these options:

W auto-tune anyway - this show will override an existing

show set to auto-tune

W proceed, no auto-tune - set the show as a Reminder

but do not auto-tune

W don't set this reminder - cancel the Reminder

Page 60

60 Plasma TV

Operation

1. First, connect power cord correctly. At this moment, the TV switches to standby mode.

In standby mode to turn TV on, press the ,TV/VIDEO , CH (

D/E

) button on the TV or press

the POWER, TV/VIDEO, TV INPUT, CH (

D/E

), Number (0 ~ 9) button on the remote control.

Notes:

• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

• After turning on the TV, it will take up to a week for the TV Guide On Screen system to receive full

• listings data.

• Illuminates orange in standby mode. When the TV is turned on, the indicator will blink green for 3-4

• seconds before the picture is seen.

• When the TV is turned On, the TV Guide On Screen system is automatically displayed. The screen

• may be slightly delayed if the TV was unplugged and then powered On.

2. Select the viewing source by using TV/VIDEO, TV INPUT button on the remote control.

This TV is programmed to remember which mode it was last set to, even if you turn the TV off.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to

standby mode.

Operation

TTurning the TV On

urning the TV On

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just an

example to help you with the TV operation.

Page 61

Owner’s Manual 61

Operation

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use

D/E

button to select the OPTION

menu.

2. Press the

GG button and then use

D/E

button to select Language.

3. Press the

G button and then use

D/E

button to select your desired language. From this point on, the on-screen menus will be shown in the selected language.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

TV Setup

On-screen Menus Language Selection

Page 62

62 Plasma TV

Operation

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes.

- A password is required to gain access to EZ Scan menu if the Lock System is turned on.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

G button and then use

D / E

button to select EZ Scan.

3. Press the ENTER button to begin the channel search.

Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

G button and then use

D / E

button to select Manual Scan.

3. Press the

G button and then use

D / E

button to select TV, DTV, CATV, and

CADTV.

4. Press the

G button and then use

D / E

button to select channel number you

want to add or delete.

5. Press the ENTER button to add or delete for the channel number.

6. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Notes:

• This channel number is a physical channel number, which is different from the normal channel number shown in Channel

Edit.

• When a cable box connects to the physical channel 2,3 or 4 in the TV Guide On Screen system Setup, cable chan-

nels(CATV or CADTV) will not be scanned by EZ Scan or Manual Scan.

• When inserting the CableCARD

, CATV, CADTV is not working in Manual Scan.

• TV: analog antenna(over-the-air) TV signal

DTV: digital antenna(over-the-air) TV signal

CATV: analog cable TV signal

CADTV: digital cable TV signal

EZ Scan (Channel Search)

Setup Menu Options

Manual Scan

- A password is required to gain access to Manual Scan menu if the Lock System is turned on.

Page 63

Owner’s Manual 63

Note:

• When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen Setup, cable channels(CATV or

CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available.

Page 64

64 Plasma TV

Operation

- Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Main Input.

3. Press the

G button and then use

D / E

button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGB-PC), HDMI1/DVI or HDMI2.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Note:

• To toggle RGB-DTV and RGB-PC, select RGB-DTV(or RGB-PC) and press

button.

Main Picture Source Selection

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Input Label.

3. Press the

G button and then use

D / E

button to select the source: Video, Front

Video, Component1, Component2, RGB, HDMI1/DVI or HDMI2.

4. Press the

F / G button to select the label.

5. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Input Label

- Choose preset labels for your channels.

- If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Channel Label.

3. Press the

G button. You will now see a screen filled with Labels and a preview screen.

4. Use the CH

D/E

button to select a channel to Label.

5. Use

D / E

/ F / G

button to select the appropriate label for the channel, then press ENTER button to set the Label to

the selected channel.

- If you press ENTER button in TV viewing mode, you will see the channel banner. • For example:

Channel Label Setup

DTV 2-0

CNN

DOLBY DIGITAL

- Sets a label to each input source or lets you skip the input source which is not

in use when you press TV/VIDEO button.

Setup Menu Options

Page 65

Owner’s Manual 65

- Use to quickly reset all the Video menu options to their original factory preset values.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the

G button and then use

D / E

button to select Video Reset .

3. Press the

G button to reset the Video menu options to original values.

VVideo Reset

ideo Reset

Operation

- Adjust the picture appearance to suit your preference and viewing situations.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the

G button and then use

D / E

button to select the desired picture option

(

Contrast, Brightness, Color, Sharpness, or Tint ).

3. Press the

G button and then use F / G button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below:

Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports.

• You can also use the

VIDEO menu to adjust EZ Picture.

2. Press the EXIT button to save and return to TV viewing or press MENU button to return to the previous menu.

EZ Picture

Manual Picture Control (

Custom

option)

- Choose one of three automatic color adjustments. Set to warm to enhance hotter

Page 66

66 Plasma TV

Operation

- Other languages may be available if a digital signal is provided by the broadcasting station.

1. Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below:

Custom (your own settings), Normal, Stadium, News, Music, and Theater.

• You can also adjust

EZ Sound in the AUDIO menu.

2. Press EXIT button to save and return to TV viewing or press MENU button to return to the previous

menu.

EZ Sound

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select the desired sound option

(

Balance, Treble, or Bass).

3. Press the

G button and then use F / G button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Manual Sound Control (

Custom

option)

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select Audio Language.

3. Press the G button and then use

D / E

button to select: English, Spanish, or

French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches to

Custom.

Normal, Stadium, News, Music, and Theater are preset for good sound quality at the factory and are not adjustable.

- Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. EZ SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select EZ SoundRite.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

EZ SoundRite

- Adjust the sound to suit your taste and room situations.

Audio Language

Audio Menu Options

Page 67

Owner’s Manual 67

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select TV Speaker.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

TV Speakers On/Of

f Setup

- Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off.

Operation

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select Front Surround.

3. Press the

G button and then use

D / E

button to select Off, 3D EchoSound

System

or SRS (Sound Retrieval System) TruSurround XT..

•

3D EchoSound System

Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into stereo sound.

•

SRS TruSurround XT

Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Front Surround

- is a trademark of SRS Labs, Inc.

- TruSurround XT technology is incorporated under license from SRS Labs, Inc.

- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Page 68

68 Plasma TV

Operation

1. Use the SAP button to select your desired MTS mode in a analog signal. Each time you press the SAP button, Mono,

Stereo, or SAP appear in turn.

• If other languages are available on the digital signal, select them with the SAP button.

2. Press EXIT button to save and return to TV viewing.

Stereo/SAP

Broadcasts Setup

- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.

- When having selected Stereo or SAP button on the remote control, this TV can only receive the signal when the TV station transmits the proper signals.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to mono sound during stereo/SAP broadcasting.

- Stereo or SAP can be received in a Analog channel.

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the G button and then use

D / E

button to select BBE.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

BBE

- BBE High Definition Sound restores clarity and presence for better speech intelligibility and music realism.

• Manufactured under license from BBE Sound, Inc.

• Treble, Bass or BBE aren’t suitable for

SRS TSXT mode.

Audio Menu Options

Page 69

Owner’s Manual 69

Operation

- Timer function operates only if the current time has been set.

- Off-Timer function overrides On-Timer function if they are both set to the same time.

- The TV must be in standby mode for the On-Timer to work.

- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.

On/Of

On/OfffTT

imer Setup

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

G button and then use

D / E

button to select Off Timer or On Timer.

3. Press the G button and then use

D / E

button to select On.

• To cancel

On/Off timer function, select Off.

4. Press the

G button and then use

D / E

button to set the hour.

5. Press the

G button and then use

D / E

button to set the minutes.

6. For only

On timer function

Press the

button and then use

D / E

button to select the channel at turn-on.

Press the

G button and then use

D / E

button to set the sound level at turn-on.

7. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

- The time is set automatically from a digital channel signal.

- The digital channel signal includes information for the current time provided by the broadcasting station.

- Set the clock manually, if the current time is set incorrectly by the auto clock function.

- When you set up the TV Guide On Screen system,

Auto Clock menu is not selected.

01. Press the MENU button and then use

D / E

button to select the TIME

menu.

2. Press the G button and then use

D / E

button to select Auto Clock.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press the

G button and then use

D / E

button to select your viewing area time

zone:

Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.

5. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

- If current time setting is wrong, reset the clock manually.

- When you set up the TV Guide On Screen system,

Manual Clock menu is not

selected.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

G button and then use

D / E

button to select Manual Clock.

3. Press the

G button and then use F / G button to select either the year, date, or

time option. Once selected, use the

D / E

button to set the year, date, and time

options.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Auto Clock Setup

Manual Clock Setup

TTime Menu Options

ime Menu Options

Page 70

70 Plasma TV

Operation

Auto Of

Auto Offf

- If set to on and there is no input signal, the TV turns off automatically after 10 minutes.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

G button and then use

D / E

button to select Auto Off.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Sleep

SleepTT

imer

- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.

- You can also set up the

Sleep Timer in the TIME menu.

1. Press the TIMER button repeatedly to select the number of minutes. First the

Off option appears on the screen,

followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to

count down from the number of minutes selected.

3. To check the remaining minutes before the TV turns off, press the TIMER button once.

4. To cancel the Sleep Timer, press the TIMER button repeatedly to select

Off.

TTime Menu Options

ime Menu Options

Page 71

Owner’s Manual 71

Operation

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed.

- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.

- Horizon aspect ratio is not available for Component 1-2 (480p/720p/1080i)/RGB-DTV (480p/720p/1080i)/HDMI1/DVI-DTV (720p/1080i)/DTV(720p/1080i), HDMI2-DTV(720p/1080i) input source.

- In RGB-PC/DVI-PC input source, only use 4:3 or 16:9 aspect ratio are available.

- Note: If a fixed image is displayed on the screen for a long time, it image may become imprinted on the screen and remain visi-

ble.

•

Set By Program

Select the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9)

•

4:3

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.

•

16:9

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

•

Horizon

Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

•

Zoom 1

Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

•

Zoom 2

Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.

•

Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture size, the image may become distorted.

You can adjust the enlarge proportion of Cinema Zoom using

D / E

button. The adjustment range is 1~16.

1. Press the RATIO button repeatedly to select the desired picture format.

You can also adjust

Aspect Ratio in the OPTION menu.

Cinema 3:2 Mode Setup

- Most movies are 24 frames/sec, but TV signal is 30 frames/sec.

This option lets the TV do 3:2 pull-down operation for you to watch movies at the best motion appearance.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Cinema 3:2 Mode.

3. Press the

button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Option Menu Features

Aspect Ratio Control

Note: This feature operates only in 480i mode.

Page 72

72 Plasma TV

Option Menu Features

Operation

Caption/T

ext

Analog Broadcasting System Captions

- Select a caption mode for displaying captioning information if provided on a program.

- Analog caption displays information at any position on the screen.

- Text displays information, usually at the bottom position and is used for a data service.

- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.

- This TV is programmed to memorize the caption/text mode which was last set to, when you turn the power off.

Digital Broadcasting System Captions

- Choose the language you want the DTV/CADTV Captions to appear in.

- Languages can be chosen for digital sources only if they are included on the program.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption/Text.

3. Press the

G button and then use

D / E

button to select caption: CC1, CC2, CC3,

CC4, Text1, Text2, Text3, or Text4.

•

CAPTION

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

•

TEXT

The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption/Text.

3. Press the

G button and then use

D / E

button to select available caption lan-

guages:

English, Spanish, or French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Caption

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4.

•

EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

.2. Press EXIT button to save and return to TV viewing.

• You can also use the

OPTION menu to select Caption/Text.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema 3:2 Mode

Caption

Caption / Text

Caption Option

Language

ISM Method

Low Power

Auto Demo

English

Spanish

French

CABLE

Page 73

Owner’s Manual 73

Operation

Caption Option

- Customize the DTV/CADTV captions that appear on your screen.

1. Press the MENU button and then use

D / E

button to select the OPTION

menu.

2. Press the

G button and then use

D / E

button to select Caption Option.

3. Press the

G button and then use F / G button to select Custom.

4. Use

D / E

button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.

•

Size: Set the size of the words.

•

Font: Select a typeface for the words.

•

Text Color: Choose a color for the text.

•

Text Opacity: Specify the opacity for the text color.

•

Bg (Background) Color: Select a background color.

•

Bg (Background) Opacity: Select the opacity for the background color.

•

Edge Type: Select an edge type.

•

Edge Color: Select a color for the edges.

5. Press EXIT button to return to TV viewing or press MENU button to return

to the previous menu.

Page 74

74 Plasma TV

Operation

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image ; even though the image is changed. Use our unique method to minimize any fixed image on the screen.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select ISM Method.

3. Press the G button and then use

D / E

button to select either Normal, White

Wash

, Orbiter or Inversion.

•

Normal

If image sticking is never a problem, ISM is not necessary - set to Normal.

•

White Wash

White Wash removes permanent images from the screen.

Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button.

•

Orbiter

Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per 2 minutes: Left → Right → Upside → Downside → Right → Left → Downside → Upside.

•

Inversion

Inversion will automatically invert the plasma display panel color every 30 minutes.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

ISM (Image Sticking Minimization) Method

Option Menu Features

Page 75

Owner’s Manual 75

Operation

Low Power

- Low power reduces the plasma display power consumption.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Low Power.

3. Press the G button and then use

D / E

button to select On or Off.

• When you select

On, the screen darkens.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

- Displays the slide show to explain the main features of this TV.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Auto Demo.

3. Press EXIT button to stop Auto Demo.

Note : The images on the Auto Demo may differ from the actual products.

Auto Demo

Page 76

76 Plasma TV

Operation

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enable the lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters:

Movie Ratings :

• Blocking Off (Permits all programs)

• G (General audience)

• PG (Parental guidance suggested)

• PG-13 (Parents strongly cautioned)

• R (Restricted)

• NC-17 (No one 17 and under admitted)

• X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

• TV-G (General audience)

• TV-PG (Parental guidance suggested)

• TV-14 (Parents strongly cautioned)

• TV-MA (Mature audience only)

• TV-Y (All children)

• TV-Y7 (Children 7 years older)

TV Rating Children:

• Age (applies to TV-Y, TV-Y7)

• Fantasy Violence (applies to TV-Y7)

TV Rating General:

• Age (applies to TV-G, TV-PG, TV-14, TV-MA)

• Dialogue - sexual dialogue (applies to TV-PG, TV-14)

• Language - adult language (applies to TV-PG, TV-14, TV-MA)

• Sex - sexual situations (applies to TV-PG, TV-14, TV-MA)

• Violence (applies to TV-PG, TV-14, TV-MA)

Input Block

• Video, Front Video (On, Off)

• Component 1, 2 (On, Off)

• RGB, HDMI1/DVI, HDMI2 (On, Off)

Lock Menu Options

Page 77

Owner’s Manual 77

Operation

Parental Lock Setup

1. Press the MENU button and then use

D / E

button to select the LOCK menu.

Then, press the

G button

• The TV is set up with the initial password “0-0-0-0”.

2. Use the

D / E

button to choose from the following Lock Menu options. Once the

option is selected, change the settings to your preference.

• Lock System: Enables or disables the blocking scheme you set up previ-

ously.

• Set Password: Change the password by inputting a new password twice.

• Block Channel: Blocks any channels that you do not want to watch or that you do not want your children to watch.

• Movie Rating (MPAA): Blocks movies according to the movie ratings lim-

its specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

• TV Rating-Children: Prevents children from watching certain children's TV

programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.

• TV Rating-General: Based on the ratings, blocks certain TV programs that

you and your family do not want to view.

• Input Block: Enables you to select a source to block from the external

source devices you have hooked up.

3. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Note:

• If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.

- Set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu.

Page 78

78 Plasma TV

Operation

Cable menu options

- The Cable sub menu displays when inserting the CableCARDTMto the TV.

- The CableCARD

type is Motorola, Scientific Atlanta (SA), or SCM etc. The OSD (On screen display) is different from your TV according to your CableCARD

type.

Scrambled channel

- Insert the CableCARDTM. If you do it at first, it takes about 1 minute to exchange the data between the TV and the CableCARD

. Then, TV screen

displays as shown right.

- Let your cable TV service provider know CableCARD

ID and Host ID.

- If your cable TV service provider is registered CableCARD

ID and Host ID,

you can watch the premium or high value channel.

- If you ever registered to the cable TV service provider, you can watch the premium or high value channel without a message.

- If the certificate doesn’t match between the TV and the CableCARD

the OSD (On screen display) displays as shown left.

In case of Scientific Atlanta CableCARD™

i.e) CableCARD™/ Host ID Screen

1. Press the MENU button and then use

D / E

button to select the CABLE menu.

2. Press the G button and then use

D / E

button to select your desired item.

3. Press the

G button.

4. Press EXIT button to return to TV viewing.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE

SA CableCARD™ Diag Screen G

SA CableCARD™/Host ID Screen

Exit

In order to start service for this device, please contact customer service at Ph#: 1-866-303-0422

CableCARD(tm): 0-010-405-698-001 HOST ID: 0-080-000-000-226

EXIT

CableCARD(tm) Message

Exit

In order to start cable service for this device, please contact SuperVision Cable at 1-800-555-8888

POD ID: 7-561-034-449-009

Host ID: 0-100-331-784-018

EXIT

CableCARD™ Message

Please call your operator and report an invalid CableCARDTM.

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just example to help

the TV operation.

As shown, the pairing number means your TV and CableCARD

ID. For further information regarding cable TV service, contact your local cable TV service provider(s).

CableCARD

CableCARD™™

Function

Page 79

Owner’s Manual 79

Operation

- If an emergency situation occurs during watching the TV/DTV/CATV/CADTV, you can receive a message from cable TV service provider(s).

- When receiving an emergency message, the message is displayed on the screen as shown below or the channel is changed automatically to a channel that maintains the emergency message. The message will automatically disappear after some time and return to the last channel.

Emergency Action Notification

Hurricane will be coming!!!

Cable Channel List

Emergency

Alert Message

1. If you enter the Channel Edit after running the EZ Scan without CableCARDTM, you can see the cable channel list

as the picture 3 above.

2. Insert the CableCARD

. Then, the TV receive a new cable channel list which is usually one part channel. It takes

about 2~3 minutes to gather the cable channel list after inserting the CableCARD

as the picture 4 above.

(Occasionally more than that time)

1. 2.

Page 80

80 Plasma TV

Operation

What is Memory Card

Precaution for Using the Memory Card

Notes on Memory Card

This is a device equipment to communicate the data between AV external equipment. It’s used to a digital camera, camcorder, MP3 player, notebook or PDA.

- Please be sure to insert the correct memory card type in the right direction. (Confirm between the two memory slots before insertion.)

- Don’t insert the metal substances into the slots of the memory card.

- Do not bend, drop or apply strong shock to memory card.

- After pulling the memory card out from the TV, please keep the memory stick in a appropriate case to prevent it from static shock.

- The stored data may be changed or lost as a result of misuse, static electricity.

- Do not turn the power off while the memory card is in operation.

- Don’t eject the memory card while in use. Otherwise, it may cause a data loss or card damage.

- Insert only one card to each slot.

- To prevent a change or loss for stored data, don’t misuse the TV or don’t let static electricity or electrical noise for TV.

- This Company takes no responsibility for problems such as the damage or malfunction that occurs while using the TV set, inappropriate TV settings, or any other reasons, except for defects or malfunctions intrinsic to the product.

- Ensure to use a memory card that lists the manufacturers name and serial number.

- The manufacturer will not be responsible for any data damage. Making back up data is strongly recommended.

- Make sure to comply with the following steps when ejecting a memory card.

- Each Memory Card is complied with standard.

- It’s available to play the Photo / Music file on Memory Card.

Page 81

Owner’s Manual 81

Operation

Inserting a Card

1. Insert the Memory Card to Memory card slots of TV side panel.

2. Two slots support defferent types of the Memory Cards.

3. If a Memory Card is not inserted, each slot is disabled.

Ejecting a card

1. Press the M/C EJECT button on the remote control.

2. Select the

Slot 1 or Slot 2 based on the inserted card location.

If you select

Cancel, OSD will disappear.

3. Eject the card by the hand.

Caution: Press the M/C EJECT button of remote control

before removing the memory card. Failure to do so may damage the card.

How to insert and eject the Memory Card

A sort of file

Compatilbility

Photo Image (JPEG)

*.jpg

An error may occur if you use a memory card with greater than the specified capacity.

Unsupported or damaged JPEG or MP3 files can cause errors. Do not try to change the file extension of unsupported file types to the file extension of supported file types.

*.mp3

Memory card

capacity

Unsupported or

damaged file

CF (CompactFlash) : 4GB

MD (Microdrive) : 4GB

CF+|| (MagicStor) :2.2GB

SD (Secure Digital) : 1GB

MMC (MultiMedia Card) : 1GB

MS (Memory Stick) :128MB

MS Pro (Memory Stick Pro) : 1GB

SMC (Smart Media Card) : 128MB

xD (Extream Digital Picture Card) : 512MB

Music File (MP3)

Slot 1

MMC

SMC

Slot 2

MultiMediaCard

Secure Digtal

SmartMedía

xD-Picture Card

MEMORY STICK

CompactFlash

Microdrive

magicstor

CF MD MagicStor

Memory Card type

- Use the specified card based on the slot location.

- 9 types of Memory Card can be used for this Plasma TV.

- Some MagicStor Plus card is not complied with the TV.

Available file in mode

EMORY

TICK

PRO

MS Pro

CF Type I/II

Page 82

82 Plasma TV

Operation

Page 83

Owner’s Manual 83

Operation

1. Use the CHD/Ebutton to navigate thumbnail photos in pages.

2. Use MARK button to mark or unmark a photo. When one or more photos are marked, you can view or slideshow only

the marked ones.If no photo is marked, you can view or slideshow all photos in the folder.

3. Use

D / E

/ F / G

button to navigate the appropriate thumbnail photos, then press the ENTER button to show the PopUp

menu.

•

View: See the selected item to the full screen.

View state change to slide show state by pressing the PLAY (

G) button.

•

Slide Show: Start a slide show with all photos in the folder. The slide show state can be changed to the view state by

pressing the Pause (

||) button. Before starting a slide show, you can choose the slide show interval

(3,6 or 9 seconds). Note: 4 hours later, Slide Show is ended, automatically.

•

Mark All: Mark all photos on the screen.

•

Unmark All: Unmark all marked photos.

•

Cancel: Hide the pop-up menu.

4. Repeatedly, press EXIT button to return to TV viewing or press button to return to the entry menu.

- When you select Photo in entry menu, you will now see a screen filled with thumbnail photos.

Photo List

Screen Components

Usable Card memory

Folder List

Current page/Total page

Marked thumbnail photo number

Direct Buttons

Card type

Photo Selection and PopUp Menu

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just an

example to help you with the TV operation.

Page 84

84 Plasma TV

Operation

- When you select Music in the entry menu, you will now see a screen filled with music titles.

- Purchased MP3/music files may contain copyright restrictions. Playback of these files may not be supported by this model.

Music List

Screen Components

Usable Card memory

Folder List

Current page/Total page

Marked music title number

Direct Buttons

Card type

Current playing time/Total playing time

4394 KB 1 Kbps

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just an

example to help you with the TV operation.

Page 85

Owner’s Manual 85

Operation

1. Use the CH

D / E

button to navigate music titles in pages.

2. Use MARK button to mark or unmark a music title. When one or more music titles are marked, the marked music will be played by turns. For example, if you want to listen to only one music repeatedly, just mark the music only and play it. If no music title is marked, all the music in the folder will be played in sequence.

3. Use

D / E

/ F / G

button to navigate the appropriate music titles, then press the ENTER button to set the pop-up menu.

• Play: Play the selected music.

• Stop Play: Stop the play.

• Play With Photo: Start playing the selected music by turns and then move to the Photo List.

• Mark All: Mark all music titles in the folder.

• Unmark All: Unmark all marked music.

• Cancel: Hide the pop-up menu.

4. Repeatedly, press EXIT button to return to TV viewing or press button to return to the entry menu.

- If you don't press any button for 40 seconds, the play information box (as shown in the below) will float

as a screen saver.

Notes:

• When music is playing, is displayed in front of the music title.

• If you press any button except VOL

D/E

, MUTE,

, II,

, I

FF,GG

I buttons, screen saver is stopped.

• T

, II,

, I

FF,GG

I buttons on the remote control are also available in this mode.

* The ‘Screen Saver’? Screen saver is to prevent screen pixel burning caused by long time still picture.

Page 86

86 Plasma TV

Operation

- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other

source will show a smaller inset image.

- Twin Picture mode splits the screen into two images, allowing two picture sources to be shown on the TV screen at the same

time. Each source is given half the screen.

- In PIP/POP/Twin Picture mode, the screen savers such as "

No Signal", "Rating Blocked" , "Channel Blocked", or "Aux

Blocked

" may not be displayed on screen.

Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.

PIP Off

PIP Mode POP Mode

Twin Picture Mode

1. Press the PIP button.

2. Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+

PIPCH- button to select a channel for the sub picture.

(You can’t select DTV for main and sub picture simultaneously).

Repeatedly, press the SWAP button to switch the main and sub pictures.

• Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI/DVI input sources for the main picture can’t be used to

swap the main and sub pictures.

Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the

Sub Input in the SETUP menu.

Main Picture Source

Available Sub Picture Sources

DTV Analog

Analog, Video, and Front Video DTV, Analog, Video, and Front Video

Main Picture Sub Picture Main Picture Sub Picture

F TV 2-0

TV 4-0

TV 6-0

Normal Mode

PIP (Picture-In-Picture) / POP / Twin Picture

Remote Control

WWatching PIP/POP/T

atching PIP/POP/T

win Picture

Selecting an Input Signal Source for PIP/T

win Picture

Swapping the PIP

Swapping the PIP/T/T

win Picture

TV Program selection for PIP

Page 87

Owner’s Manual 87

Operation

In PIP mode, press the

D /

Page 88

88 Plasma TV

Operation

APM (Adaptive Picture Mode)

- Allows a viewer to select their preferred picture mode after compairing the four different picture (Daylight, Normal, Night Time

and Custom) settings.

1. Press the APM button at once. As shown below, the screen is

divided to 4-split. Use the

D / E

/ F / G

button to navigate 4 EZ Pictures. By press-

ing the ENTER button, you can select the desired mode.

2. Press the APM button, again. As shown below, the 4-same

screens are displayed. You can easily compare with 4 modes.

3. Use the

D / E

/ F / G

button to navigate 4 EZ Pictures. By press-

ing the ENTER button, you can select the desired mode.

4. Press EXIT button to return to TV viewing.

Note: While operating the 4-split, any button except APM, ENTER, EXIT, VOLUME

D/E

, MUTE button on the

remote control are not available.

Page 89

Owner’s Manual 89

Operation

4 : 3

16 : 9

The original aspect ratio of the video is 4:3

The original aspect ratio of the video is 16:9(wide)

The video resolution is 720x480i

The video resolution is 720x480p

The video resolution is 1280x720p

The video resolution is 1920x1080i

Multilingual : The program contains two or more audio

services. Press the SAP button to select wanted

Audio.

Caption: => The program contains one or more cap-

tion services. Press the CC button to select wanted

Closed caption.

The program contains V-Chip information. Refer to the

<LOCK Menu>.

D (Dialogue), L (Language), S (Sex), V (Violence), FV

(Fantasy Violence)

480i 480p 720p

1080i

Operation: • Watching TV/DTV/CATV/CADTV

• Watching Video, Front Video

• Watching IEEE 1394

• In Component1, Component2, RGB,

HDMI/DVI modes, INFO button is not working.

Function: • Show the present screen information.

• On Watching with the upper Input signal,

press the INFO button.

• Press the INFO button or EXIT button to

exit. A: Banner information B: Program title C: Day of week, Month, Year D: Program start time E: Program progress bar F: Program finish time G: Present time H: Additional information. Refer to the icon

explanation on the right.

- Brief Info shows the present screen information.

- Press the INFO button to show the Brief Info on the screen.

- INFO button does not work in Component1, Component2, RGB, and HDMI/DVI modes.

- Press the INFO button or EXIT button to exit.

Brief Info.

Page 90

90 Plasma TV

Operation

- Nothing to do with Caption on/Off using Mute button, the mode selected Caption/Text is to be displayed.

- When you repeatedly press the Mute button, the sound mode is changed in turn. (Refer to the picture below)

Note:

• EZ Mute does not operate in Component/RGB/HDMI/DVI modes.

Mute : Sound is muted.

EZ Mute : a special mute mode to

activate the closed caption, automatically.

EZ Mute

Mute Off : Sound is enabled.

1. Press the FREEZE button in 720p or 1080i mode.

2. Use the

D / E

/ F / G

buttons to select the screen section to be magnified.

3. To return to normal viewing, press the FREEZE button again.

Note : The Magnify feature is available only in 720p or 1080i mode, but the FREEZE button works in all video formats.

- Enlarges the picture with correct proportions.

- When enlarging the picture, the image may become distorted.

Freeze & Magnify (DTV/CADTV 720p, or 1080i mode only)

Mute

EZ Mute

Page 91

Owner’s Manual 91

Operation

• When RGB connect to PC input and select the RGB-PC in Main Input, this function is used.

• When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used.

• In RGB-DTV mode, SIZE and PHASE is not available.

• After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.

- Display PC Adjust Menu using Adjust button.

- Position : Adjust the screen position. After displaying the Adjust, select the screen position.

- Size : Adjust the screen size.

- Phase : Adjust the phase of Pixel clock. In HDMI/DVI-PC mode, PHASE is not available.

- Reset : Initializating Size, Position, Phase adjustment.

Operation

Adjustment for screen Position, Size, Phase, Reset

Screen Setup for PC mode

Page 92

92 Plasma TV

External Control Device Setup

No. Pin Name 1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection

2 3 5 4 6 7 8

RXD

TXD

GND

DTR

DSR

RTS CTS

TXD RXD

GND

DSR DTR CTS RTS

7-Wire Configurations

(Standard RS-232C cable)

D-Sub 9

3 2 5 6 4 8 7

PDP

D-Sub 9

2 3 5 4 6 7 8

RXD

TXD

GND

DTR

DSR

RTS CTS

TXD RXD

GND

DTR DSR RTS CTS

3-Wire Configurations

(Not standard)

D-Sub 9

3 2 5 4 6 7 8

PDP

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)

and control the TV’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the TV back panel.

- RS-232C connection cables are not supplied with the TV.

TType of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

External Control Device Setup

RS-232C Setup

RS-232C INPUT

(CONTROL/SERVICE)

AUDIO

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT2 INPUT

OUTPUT

AUDIO INPUT

RGB INPUT

VIDEO

HDMI 2

HDMI1 /DVI

COMPONENT INPUT 1

(MONO)

CABLE

ANTEN

DVD /DTV INPUT

IEEE-1394

COMPONENT INPUT 2

MONITOR OUTPUT

A/V INPUT

VIDEO

AUDIO

Cable

S-VIDEO

REMOTE CONTROL

Page 93

Owner’s Manual 93

External Control Device Setup

Set ID

Use this function to specify a TV ID number. Refer to ‘Real Data Mapping’. See page 94.

• Baud rate : 9600 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Communication Parameters

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

G button and then use

D / E

button to select SET ID.

3. Press the

G button and then use

D / E

button to adjust SET ID to choose the

desired TV ID number. The adjustment range of

SET ID is 1 ~ 99.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

ransmission

[Command 1]: First command to control the set. (j or k)

[Command 2]: Second command to control the set.

[Set ID]: You can adjust the set ID to choose desired TV ID

number in Setup menu. Adjustment range is 1 ~

99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.

[DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return

ASCII code ‘0x0D’

[ ]: ASCII code ‘space (0x20)’

[Command1][Command2][ ][Set ID][ ][Data][Cr]

TTransmission / Receiving Protocol

ransmission / Receiving Protocol

OK Acknowledgement

* The TVr transmits ACK (acknowledgement) based on this

format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

[Command2][ ][Set ID][ ][OK][Data][x]

Error

Acknowledgement

* The TV transmits ACK (acknowledgement) based on this

format when receiving abnormal data from non-viable functions or communication errors.

[Command2][ ][Set ID][ ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function 3: Wait more time

01. Power k a 0 ~ 1

02. Input Select k b 0 ~ 9

03. Aspect Ratio k c

04. Screen Mute k d 0 ~ 1

05. Volume Mute k e 0 ~ 2

06. Volume Control k f 0 ~ 64

07. Contrast k g 0 ~ 64

08. Brightness k h 0 ~ 64

09. Color k i 0 ~ 64

10. Tint k j 0 ~ 64

11. Sharpness k k 0 ~ 64

12. OSD Select k l 0 ~ 1

13.

Remote Control Lock Mode

k m 0 ~ 1

14. PIP/POP/Twin k n 0,1,2,5

15. PIP Position k q 0 ~ 3

16. Treble k r 0 ~ 64

17. Bass k s 0 ~ 64

18. Balance k t 0 ~ 64

19. Color Temperature k u 0 ~ 2

20. PIP Input Source k y 0 ~ 3

21. ISM Method j p 1,2,4,8

22. Low Power j q

23. Orbiter Time Setting j r 1 ~ FE

24. Orbiter Pixel Setting j s 1 ~3

COMMAND 1 COMMAND 2 DATA

(Hexadecimal)

25. Channel Tuning m a 01 ~ 87 01 ~ 87 00 ~ FE 00 ~ FF 00 ~ FF 00 ~ FF

26. Channel Add/Del m b 00 ~ 01

27. Key m c

28. Input Select x b

29. PIP Input Select x y

COMMAND 2

COMMAND 1

DATA 0

(Hexadecimal)

DATA 1

(Hexadecimal)

DATA 2

(Hexadecimal)

DATA 3

(Hexadecimal)

Command Reference List

DATA 4

(Hexadecimal)

DATA 5

(Hexadecimal)

Page 94

94 Plasma TV

External Control Device Setup

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the TV.

ransmission

Data 0: DTV

1: Analog 2: Video 3: Front Video 4: Component 1

5: Component 2 6: RGB-DTV 7: RGB-PC 8: HDMI1/DVI 9: HDMI2

Date 1: 4:3

2: 16:9 3: Horizon 4: Zoom 1 5: Zoom 2

6: Set by program 10: Cinema Zoom (1)

1F: Cinema Zoom (16)

[k][b][ ][Set ID][ ][Data][Cr]

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

01. Power (Command2:a)

G To control Power On/Off of the TV.

ransmission

Data 0 : Power Off 1 : Power On

[k][a][ ][Set ID][ ][Data][Cr]

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback presents status about each function.

Real data mapping

0 : Step 0 (SET ID ALL) 1 : Step 1 (SET ID 1)

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

63 : Step 99 (SET ID 99) 64 : Step 100

05. Volume Mute (Command2:e)

G To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

ransmission

Data 0 : Volume mute off (Volume on)

1 : Volume mute on (Volume off) 2 : Volume mute on, Caption on

[k][e][ ][Set ID][ ][Data][Cr]

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust the screen format.

You can also adjust the screen format using the RATIO button on remote control or in the Option menu.

ransmission

[k][c][ ][Set ID][ ][Data][Cr]

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command2:d)

G To select screen mute on/off.

ransmission

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

[k][d][ ][Set ID][ ][Data][Cr]

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G To adjust volume.

You can also adjust volume with the volume buttons on remote control.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][f][ ][Set ID][ ][Data][Cr]

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G To adjust screen contrast.

You can also adjust contrast in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][g][ ][Set ID][ ][Data][Cr]

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h)

G To adjust screen brightness.

You can also adjust brightness in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][h][ ][Set ID][ ][Data][Cr]

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

Page 95

Owner’s Manual 95

External Control Device Setup

09. Color (Command2:i)

G To adjust the screen color.

You can also adjust color in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’. See page 94.

[k][i][ ][Set ID][ ][Data][Cr]

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G To adjust the screen tint.

You can also adjust tint in the Video menu.

ransmission

Data Red : 0 ~ Green : 64

• Refer to ‘Real data mapping’. See page 94.

[k][j][ ][Set ID][ ][Data][Cr]

Acknowledgement

[ j ][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)

G To lock the remote control and the front panel controls on

the set.

ransmission

[k][m][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Lock off 1: Lock on

[m][ ][Set ID][ ][OK][Data][x]

14. PIP / POP / Twin Picture (Command2:n)

G To control the PIP (Picture-in-Picture)/POP/Twin picture.

You can also control the PIP/POP/Twin picture using the PIP button on the remote control.

ransmission

Data 0: PIP off

1: PIP

2: Twin Picture 5: POP

[k][n][ ][Set ID][ ][Data][Cr]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

G To adjust the screen sharpness.

You can also adjust sharpness in the Video menu.

ransmission

11. Sharpness (Command2:k)

Data Min: 0 ~ Max: 64

•

Refer to ‘Real data mapping’. See page 94.

[k][k][ ][Set ID][ ][Data][Cr]

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G To select OSD (On Screen Display) on/off.

ransmission

[k][l][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: OSD off 1: OSD on

[l][ ][Set ID][ ][OK][Data][x]

15. PIP Position (Command2:q)

G To select sub picture position for PIP.

ransmission

[k][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Right down on screen

1: Left down on screen 2: Left up on screen 3: Right up on screen

[q][ ][Set ID][ ][OK][Data][x]

16. Treble (Command2:r)

G To adjust treble.

You can also adjust treble in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 94.

[k][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

18. Balance (Command2:t)

G To adjust balance.

You can also adjust balance in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 94.

[k][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

17. Bass (Command2:s)

G To adjust bass.

You can also adjust bass in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 94.

[k][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

Page 96

96 Plasma TV

External Control Device Setup

19. Color Temperature (Command2:u)

G To adjust color temperature.

You can also adjust color temperature in the Video menu.

ransmission

Data 0: Medium 1: Cool 2: Warm

[k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

23. Orbiter Time Setting (Command2:r)

G To adjust orbiter operation time term.

ransmission

Data Min: 1 ~ Max: FE

[ j ][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

24. Orbiter Pixel Setting (Command2:s)

G To adjust pixel number in orbiter function.

ransmission

Data Min: 1 ~ Max: 3

[ j ][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

25. Tune Command (Command: m a)

G To tune channel to following physical/major/minor number

ransmission

Data 0:

Physical Channel Number(Transmit by Hexadecimal code)

NTSC air:02~45

NTSC cable: 01, 0E~7D

ATSC air:01~45

ATSC cable:01~87

Data1,Data2:

Major Channel Number (two part)/ Channel Number (One part)

Data1: High byte

Data2: Low byte

Two part channel number: Major number-Minor number

One part channel number: If the channel band is ATSC

digital cable, it can be used. In case of using one part chan

nel number, minor channel does not need.

Data3, Data 4:

Minor Channel Number Data3: High byte Data4: Low byte

Data 5:

[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]

20. PIP Input Select (Command2:y)

G To select input source for sub picture in PIP/Twin pic-

ture mode.

ransmission

Data 0: DTV

1: Analog 2: Video 3: Front Video

[k][y][ ][Set ID][ ][Data][Cr]

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

21. ISM Method (Command2:p)

G To avoid having a fixed image remain on screen.

ransmission

Data 1: Inversion

2: Orbiter 4: White Wash 8: Normal

[ j ][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

22. Low Power (Command2:q)

G To control the Low Power function on/off.

You can also adjust Low Power in Option menu.

ransmission

Data 0: Low Power off

1: Low Power on

[ j ][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

Main/Sub Picture

Two/One

Part

Channel

Using Physical Channel

Reserv

Step

Main

Sub

Two

One

Use

No Use

NTSC Air

ATSC

cable_auto

ATSC

Cable_irc

ATSC

Cable_hrc

ATSC

Cable_std

NTSC Cable

ATSC Air

Reserved

...

Reserved

Page 97

Owner’s Manual 97

External Control Device Setup

[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][Data5][x] [a][ ][Set ID][ ][NG][Data0][x]

Acknowledgement

28. Input select(Command: x b) (Main Picture Input)

G To select input source for TV.

ransmission

[x][b][][Set ID][][Data][Cr]

[b][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement

* All data are transmitted by Hexadecimal code *Two/One part Channel: 6th bit

This bit is used in a cable-ready system.

*Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using physical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example)

1. Analog channel: NTSC cable, channel number(35), main picture Command: ma 00 23 xx xx xx xx 01 attribute(0x01): main picture, two part(it’s not mandatory), using physical channel, NTSC cable ‘xx’ data: don’t care major and minor channel number in case analog channel tuning.

2. Digital channel: ATSC air, channel number(don’t know physical channel, major(30), minor(3)), sub picture Command: ma 00 xx 00 1E 00 03 A2 attribute(0xA2): sub picture, two part, not using physical channel, ATSC air ‘xx’ data: don’t care analog channel number in case digital channel tuning.

3. Digital channel: ATSC air, channel number(physical(20),major(20), minor(3)), sub picture Command: ma 00 14 00 14 00 03 82 attribute(0x82): sub picture, two part, using physical channel, ATSC air.

Data Structure

DATA(Hex)

INPUT

DTV (Antenna)

DTV (Cable)

Analog (Antenna)

Analog (Cable)

Video

Front Video

Component 1

Component 2

RGB DTV

RGB PC

HDMI1/DVI

HDMI2

29. PIP Input Select(Command: x y)

G To adjust input source for sub picture in PIP mode

ransmission

[x][y][][Set ID][][Data][Cr]

26. Channel Add/Del (Command: m b)

G To add and delete the channels

ransmission

Data 0: Channel Delete

1: Channel Add

[m][b][ ][Set ID][ ][Data][Cr]

[b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x]

Acknowledgement

27. Key (Command: m c)

G To send IR remote key code

ransmission

Data Key code: Refer to page 99.

[m][c][ ][Set ID][ ][Data][ ][Cr]

[c][ ][Set ID][ ][OK][Data][x]

Acknowledgement

Data Structure

DATA(Hex)

INPUT

DTV (Antenna)

DTV (Cable)

Analog (Antenna)

Analog (Cable)

Video

Front Video

[y][][Set ID][][OK/NG][Data][x]

Acknowledgement

Page 98

98 Plasma TV

IR Codes

G Connect your wired remote control to the Remote Control port on the TV.

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

G Configuration of frame

G Repeat code

G Lead code

• 1st frame

Low custom code

Lead

code

High custom code

Data code

Carrier frequency

CAR = 1/TC = fOSC/12

Duty ratio = T1/T

C = 1/3

• Repeat frame

C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G Bit description

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

• Bit “0”

Tf Tf

Tf=108ms @455KHz

0.56 ms 0.56 ms

1.12 ms

• Bit “1”

2.24 ms

How to Connect

Remote Control IR Codes

IR Codes

Page 99

Owner’s Manual 99

IR Codes

0F 0B 08 C4 C5 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 52 4D 5B 60 72 71 61 63 65 0A CB D6 5A D0 BF D4 D5 D7 C6 CC 76 77 AF 70 87 B0 BA B1 BD 8F 8E B2 B3 A9 92 CA 80 C8 7D

R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video Input Selection) Discrete IR Code (Front Video Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (HDMI/DVI Input Selection) Discrete IR Code (HDMI2 Input Selection) Discrete IR Code(Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) Discrete IR Code (Channel Search) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button

Code (Hexa) Function Note

TV INPUT TV/VIDEO POWER POWER ON POWER OFF RATIO TIMER Number Key 0~ 9

- (Dash) FLASHBK MUTE VOL

VOL

FAV INFO CC

D E F G

ENTER MENU EZ SOUND EZ PIC EXIT PIP PIPCH PIPCH + PIP INPUT SWAP FREEZE SAP ADJUST TV VIDEO Front Video COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV HDMI1/DVI HDMI2 Ratio 4:3 Ratio 16:9 Ratio Zoom POP 1394 PLAY PAUSE STOP REC REW FF GOTOPREV GOTONEXT TV GUIDE APM MC EJECT AUTO DEMO X STUDIO MARK

Page 100

100 Plasma TV

Programming the Remote

G The remote is a multi-brand or a universal remote. It can be programmed to operate most remote-controllable devices of

other manufacturers. Note that the remote may not control all models of other brands.

Programming a code into a remote mode

Programming the Remote

1. To find out whether your remote can operate the device without programming, turn on the device such as a VCR and press the corresponding mode button on the remote. After that, press the POWER button. If the device is turned off then it responds properly and the remote need not to be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below.

2. Press the MENU and MUTE button continuously at the same time for 2 seconds, the current selected device button will be illuminated. If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case, you have to repeat from step 2.

3. Enter code numbers using the number button on the remote by refering the code table on the following pages. When pressing the button, the light blinks at a time. If the device turned off, the programming is successful.

4. Press the MENU button to store the code. After blinking twice, this code is stored.

5. Test the remote functions to see if the device responds properly. If not, repeat from step 2.

LG 42PX5D-UB, 42PX4D, 42PX4D-UB User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual