TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equi-
lateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK. DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
2
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
1
Clean only with dry cloth.
2
Do not block any ventilation openings. Install in
3
accordance with the manufacturer’s instructions.
Protect the power cord from being walked
5
on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Only use attachments/accessories speci-
6
fied by the manufacturer.
Use only with the cart, stand, tripod, bracket,
7
or table specified by the manufacturer, or
sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
Do not install near any heat sources such as
4
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Unplug this apparatus during lighting
8
storms or when unused for long periods
of time.
Refer all servicing to qualified service per-
9
sonnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.
3
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during
10
a thunder or lighting storm.
When mounting a TV on the wall, make sure
11
not to install the TV by the hanging power
and signal cables on the back of the TV.
Do not allow an impact shock or any objects
12
to fall into the product, and do not drop onto
the screen with something.
CAUTION concerning the Power Cord:
13
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification page
of this owner's manual to be certain.
Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged
or cracked wire insulation are dangerous . Any
of these conditions could result in electric
shock or fire. Periodically examine the cord of
your appliance, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by
an authorized servicer. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the
cord exits the appliance.
Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on
the power cord to unplug the TV.
WARNING - To reduce the risk of fire or elec-
14
trical shock, do not expose this product to
rain, moisture or other liquids. Do not touch
the TV with wet hands. Do not install this
product near flammable objects such as
gasoline or candles or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
15
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GROUNDING
16
Ensure that you connect the earth ground
wire to prevent possible electric shock (i.e. a
TV with a three-prong grounded AC plug
must be connected to a three-prong grounded AC outlet). If grounding methods are not
possible, have a qualified electrician install a
separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.
Power
Supply
Short-circuit
Breaker
DISCONNECTING DEVICE FROM MAINS
17
Mains plug is the disconnecting device. The
plug must remain readily operable.
As long as this unit is connected to the AC
18
wall outlet, it is not disconnected from the
AC power source even if you turn off this
unit by SWITCH.
4
Cleaning
19
When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.
Moving
20
Make sure the product is turned off, unplugged
and all cables have been removed. It may take
2 or more people to carry larger TVs. Do not
press against or put stress on the front panel
of the TV.
Ventilation
21
Install your TV where there is proper ventilation. Do not install in a confined space such
as a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.
Take care not to touch the ventilation open-
22
ings. When watching the TV for a long period,
the ventilation openings may become hot.
If the TV feels cold to the touch, there may be
26
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor’s performance.
Avoid touching the LCD screen or holding
your finger(s) against it for long periods of
time. Doing so may produce some temporary distortion effects on the screen.
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not
dispose of this product with general household waste. Disposal of this product must be
carried out in accordance to the regulations of
your local authority.
If you smell smoke or other odors coming from
23
the TV or hear strange sounds, unplug the
power cord contact an authorized service center.
Do not press strongly upon the panel with
24
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.
IR Codes ..............................................................167
External Control Through RS-232C .......... 168
Open Source Software Notice ......................175
7
FEATURE OF THIS TV
ꔛ
Some of these features are not available on all models.
Manufactured under license from
Dolby Laboratories. “Dolby “and the
double-D symbol are trademarks of
Dolby Laboratories.
Listen to TV with wireless headset,
or enjoy viewing your mobile phone
photos on your TV.
(This is not available for all models.)
HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC."
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX,Inc. This is an official
DivX Certified device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order
to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate
the DivX VOD section in the device setup
menu. Go to vod.divx.com with this
code to complete the registration process
and learn more about DivX VOD.
“DivX Certified to play DivX video, including
premium content”
“Pat. 7,295,673; 7,460,688;7,519,274”
IMPORTANT INFORMATION TO PREVENT “IMAGE
BURN / BURN-IN” ON YOUR TV SCREEN
ꔛ
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed
on the TV for an extended period, it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
ꔛ
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged
period (2 or more hours for LCD, 1 or more
hours for Plasma).
ꔛ
Image burn can also occur on the letterboxed areas of your TV if you use the 4:3
aspect ratio setting for an extended period.
8
PREPARATION
ENERGY
CHVOL
12
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
0
9
WXYZ
P
A
G
E
SAVING
TV
AV MODE
INPUT
LIGHT
FAV
RATIO
MUTE
BACK
EXIT
ENTER
MARK
DELETE
CHAR/NUM
LIST
FLASHBK
MENU
FREEZE
Q.MENU
INFO
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
PREPARATION
1.5V 1.5V
Owner’s ManualNero MediaHome 4
Essentials CD
Not included with all models
Remote Control,
Batteries (AAA)
(Some models)
Option Extras
* Wipe spots on the exterior only
with the polishing cloth.
* Do not wipe roughly when remov-
Polishing Cloth
ing stain. Excessive pressure may
cause scratch or discoloration.
When using the VGA (D-sub 15
pin cable) PC connection, the
user must use shielded signal
interface cables with ferrite cores
to maintain standards compliance.
x 2
Component gender cable,
AV gender cable
Cleansing Cloths
(mitt)
Screw for
stand fixing
(Refer to
P. 2 4 )
3D Glasses
* Wipe spots on the exterior only with the cleansing cloths.
* Do not wipe roughly when removing stains. Excessive pressure may cause scratches or
discoloration.
* For cleaning front frame, please slowly wipe in one direction after spraying water 1-2 times
on cleansing cloths. Please remove excessive moisture after cleaning. Excessive moisture
may cause water stains on the frame.
32/42/47/55LD650
(For 32/42LD650)
x 8
(M4 x 20)
Screws for stand assembly
(Refer to P.16)
Screw for stand fixing
(Refer to P.24)
Protection Cover
(Refer to P.16)
Power Cord
9
PREPARATION
CH
Q.VIEW
VOL
POWERTV/INPUT
ENTER
Plasma TV
PREPARATION
(For 50PK950R)
x 4
x 4
(M4 x 14) (M4 x 28)
Screws for stand assembly
(Refer to P.17)
(For50/60PK950R)
Remote Control,
Batteries (AAA)
(Some models)
Cable Holder
(Refer to P.22)
Cable
Management Clip
x 2
Power Cord
Protection Cover
(Refer to P.17)
OPTIONAL EXTRAS
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
This device only works with compatible LG LED LCD TV, LCD TV or PLASMA TV.
10
Wireless Media Box
(AN-WL100W)
Wireless LAN for Broadband/
DLNA Adaptor
(AN-WF100)
FRONT PANEL INFORMATION
ꔛ
Image shown may differ from your TV.
32/42/47/55LD650
SPEAKER
Power/Standby Indicator
(Can be adjusted using the Power Indicator in the
OPTION menu.
►p.139)
CH
VOL
ENTER
MENU
INPUT
CHANNEL
(
ꕌ,ꕍ) Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
PREPARATION
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the surrounding conditions
42/47LE8500
SPEAKER
Touch Button
You can operate the button just by touching the button lightly with your finger.
VOLENTERCHMENUINPUT
CHANNEL
(
ꕍ,ꕌ)
Buttons
VOLUME
(-, +)
Buttons
ENTER
Button
MENU
Button
INPUT
Button
POWER
Button
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions
Power/Standby Indicator
(Can be adjusted using the
Power Indicator in the
OPTION menu.
►p.139)
11
PREPARATION
32/42/47/55LE5500, 32/42/47/55LE7500, 42/47LX6500
PREPARATION
SPEAKER
Emitter
(For 42/47LX6500)
It is the part equipped with
the emitter exchanging signal with 3D glasses.
Please be careful not to
block the screen with objects
or people while watching a
3D Video.
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions
Power/Standby Indicator
(Can be adjusted using the Power
Indicator in the OPTION
menu.
►p.139)
Touch Button
Light the button by touching first. At this time, you can use the desired button.
VOLENTERCHMENUINPUT
CHANNEL
(
ꕍ,ꕌ)
Buttons
VOLUME
(-, +)
Buttons
ENTER
Button
MENU
Button
INPUT
Button
POWER
Button
50/60PK950R
Touch Button
You can operate the button just by touching the button lightly with your finger.
SPEAKER
POWER
Button
INPUT
INPUT
Button
MENU
ENTER
MENU
Button
ENTER
Button
Intelligent Sensor
Adjusts picture according to the
surrounding conditions
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
The lighting is off while the TV remains on.
Carefully place the TV screen side down on
a cushioned surface to protect the screen
from damage.
Assemble the parts of the STAND BODY
2
with the STAND BASE of the TV.
M4 x 20
(42/47LE8500)
Assemble the TV as shown.
3
M4 x 16
(Other models)
STAND BODY
M4 x 24
(55LE5500,
55LE7500)
STAND BASE
18
Assemble the part of the STAND
4
REAR COVER with the TV.
Fix the 4 screws securely using the holes in
5
the back of the TV.
!
NOTE
► When assembling the desk type stand,
make sure the screws are fully tightened (If
not tightened fully, the TV can tilt forward
after the product installation). Do not over
tighten.
STAND REAR
COVER
(Other models)
(42/47LE8500)
M4 x 16
M4 x 20
DETACHMENT
Carefully place the TV screen side down on
1
a cushioned surface to protect the screen
from damage.
Remove the screws that hold the stand on.
2
PREPARATION
Detach the STAND REAR COVER from TV.
3
Detach the stand from TV.
4
19
PREPARATION
VESA WALL MOUNTING
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
PREPARATION
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
Model
32LD650,
32LE5500,
32LE7500
42/47LD650,
42/47LE5500,
42/47LX6500,
42/47LE7500,
42/47LE8500
55LD650,
55LE7500,
55LE5500
50PK950R400
60PK950R600
VESA (A * B)
A
B
20
0
100M44
*
200
200M64
*
400
400M64
*
400M64
*
400M84
*
Standar ScrewQuantity
Wall Mounting Bracket
(sold separately)
LSW100B,
LSW100BG
LSW200B, LSW200BG
LSW400B, LSW400BG
AW-50PG60M AW-50PG60MS
AW-60PG60M AW-60PG60MS
20
!
NOTE
► Screw length needed depends on the wall
mount used. For further information, refer to
the instructions included with the mount.
► Standard dimensions for wall mount kits are
shown in the table.
► When pur
installation manual and all parts nece
assembly are provided.
► Do not use screws longer than the standard
dimension, as they may cause damage to the
inside t
► For wall mounts that do not comply with the
VESA standar
chasing our wall mount kit, a detailed
ssary for
o the TV.
d screw specifications, the length
of the screws may differ depending on their
specifications.
► Do not use screws that do not comply with the
VESA standar
Do not use fasten the screws too strongly, this
may damage the TV or cause the TV to a fall,
leading to personal injury. LG is not liable for
these kinds of accidents.
► LG is not liable for TV damage or personal
injur
y when a nonmount is used or the consumer fails to follow
the TV installation instructions.
d screw specifications.
VESA or non specified wall
CAUTION
► Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to
electric shock.
CABLE MANAGEMENT
ꔛ
Image shown may differ from your TV.
32/42/47/55LD650
Connect the cables as necessary.
1
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
It will help prevent the power cable from
being removed by accident.
After connecting the cables as necessary,
2
install the CABLE HOLDER as shown
and bundle the cables.
Plasma TV
After connecting the cables as necessary,
1
install the CABLE HOLDER as shown
and bundle the cables.
CABLE HOLDER
CABLE HOLDER
22
(For 50/60PK950R)
Connect the cables as necessary.
1
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP
2
into the TV until clicking sound.
CABLE HOLDER
HOW TO REMOVE THE CABLE
MANAGEMENT CLIP
► Hold the CABLE MANAGEMENT CLIP with
both hands and pull it backward as shown.
DESKTOP PEDESTAL INSTALLATION
ꔛ
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
4 inches
4 inches
4 inches
CAUTION
► Ensure adequate ventilation by following the clearance recommendations.
► Do not mount near or above any type of heat source.
4 inches
PREPARATION
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees
to suit your viewing position.
23
PREPARATION
PREPARATION
ATTACHING THE TV TO A DESK
(For 32/42LD650, 32LE5500, 32LE7500)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, poten-
tially causing injury or damaging the product.
Stand
1-Screw
( provided as parts of the product)
Desk
WARNING
► To prevent TV from falling over, the TV should be securely attached to the floor/wall per installa-
tion instructions. Tipping, shaking, or rocking the machine may cause injury.
24
KENSINGTON SECURITY SYSTEM
ꔛ
This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security
System cable as shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington
Security System.
For further information, contact http://www.kensington.com,
the internet homepage of the Kensington company. Kensington
sells security systems for expensive electronic equipment such
as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
ꔛ
You should purchase necessary components to prevent the TV from tipping over (when not using a
wall mount).
ꔛ
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward
direction, potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
ꔛ
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the
picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the
bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
PREPARATION
ꔛ
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the
rope so it becomes horizontal between the wall and the product.
!
NOTE
► Use a platform or cabinet strong enough and large enough to support the size and weight of
the TV.
► To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are
the same.
25
PREPARATION
H/P
H/P
ꔛ
To prevent damage do not connect to the power outlet until all connections are made between the
devices.
ꔛ
PREPARATION
Image shown may differ from your TV.
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wall
Antenna
Socket
Outdoor
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 Ω)
ANTENNA/
CABLE IN
or
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
or
ANTENNA/
Cable TV
CABLE IN
Wall Jack
RF Coaxial Wire (75 Ω)
ꔛ
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install
properly.
ꔛ
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
ꔛ
If the antenna is not installed properly, contact your dealer for assistance.
26
EXTERNAL EQUIPMENT SETUP
ꔛ
To prevent the equipment damage, never plug in any power cords until you have finished connecting all
equipment.
ꔛ
I
mage shown may differ from your TV.
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals with an external digital set-top box.
However, if you do receive digital signals from a digital set-top box or other digital external device.
EXTERNAL EQUIPMENT SETUP
Component Connection
1. How to connect
Connect the video outputs (Y, P B, PR
1
digital set-top box to the COMPONENT IN
VIDEO 1, 2, or 3* jacks on the TV. Match the
jack colors (Y = green, P
Connect the audio output of the digital set-top
2
box to the COMPONENT IN AUDIO 1, 2, or 3*
jacks on the TV.
2. How to use
ꔛ
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top
box operation.)
ꔛ
Select theComponent1, Component2, or
Component3*input source on the TV using the
INPUTbutton on the remote control.
* Component3: For LED LCD TV
B = blue, and PR = red).
YLRPBP
)
of the
12
RGB IN (PC)
/DVI IN
3
OPTICAL
(RGB/DVI)
DIGITAL
2
AUDIO IN
AUDIO OUT
1
2
YPBP
1
VIDEO
B/PB, CR/PR
Y, C
Resolution
720x480i
720x480p
Horizontal
Frequency(KHz
15.7
359.94
15.7560.00
31.4759.94
31.5060.00
720x576i15.62550.00
720x576p31.2550.00
44.9659.94
1280x720p
37.5050.00
45.0060.00
33.7259.94
1920x1080i
28.12550.00
33.7560.00
56.2550.00
1920x1080p
67.43259.94
67.5060.00
R
RS-232C IN
(
CONTROL&SERVICE)
L(MONO)
VIDEO
AUDIO
L R
R
AUDIO
Vertical
)
Frequency(Hz
AV IN 1
R
COMPONENT IN
)
27
EXTERNAL EQUIPMENT SETUP
COMPONENT
INAV
IN
1
For LED LCD TV
EXTERNAL EQUIPMENT SETUP
USB IN 1USB IN 2
R
P
B
COMPONENT IN3
AUDIO / Y P
1
H/P
IN 4
AV IN2
VIDEO / AUDIO
2
R
DVI to HDMI Connection
1. How to connect
Connect the DVI output of the digital set-top
1
box to the HDMI/DVI IN 1, 2, or 3* jack on the
TV.
Connect the digital set-top box audio output to
2
the AUDIO IN (RGB/DVI) jack on the TV.
2. How to use
ꔛ
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-
top box.)
ꔛ
Select the HDMI1, HDMI2, or HDMI3* input source
on the TV using the INPUT
control.
* HDMI3: For 32/42/47/55LE5500, 32/42/47/55LE7500,
50/60PK950R, 42/47LE8500, 42/47LX6500
button on the remote
YLRPBP
RS-232C IN
(
LAN
ꔡ
WIRELESS
CONTROL
RGB IN (PC)
/DVI IN
3
(RGB/DVI)
2
AUDIO IN
1
2
YPBP
1
1
2
OPTICAL DIGITAL
AUDIO OUT
VIDEO
CONTROL&SERVICE)
L(MONO)
VIDEO
L R
R
AUDIO
AUDIO
R
28
!
NOTE
► A DVI to HDMI cable or adapter is required for this con-
nection. DVI doesn't support audio, so a separate audio
connection is necessary.
DVI OUTPUT
LR
AUDIO
S
O
HDMI Connection
1. How to connect
Connect the digital set-top box to HDMI/DVI IN
1
1, 2, 3 or 4* jack on the TV.
No separate audio connection is necessary.
2
HDMI supports both audio and video.
2. How to use
ꔛ
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-
top box.)
ꔛ
Select the HDMI1, HDMI2, HDMI3, or HDMI4* input
source on the TV using the INPUT
remote control.
* HDMI4: For 32/42/47/55LE5500, 32/42/47/55LE7500,
50/60PK950R, 42/47LE8500, 42/47LX6500
!
NOTE
► If an HDMI cable doesn’t support High
Speed HDMI, it can cause flickers or
no screen display. In this case use the
latest cables that support High Speed
HDMI.
► HDMI Audio Supported Format: Dolby
Digital, PCM
button on the
HDMI-DTV
Resolution
720x480p
720x576p31.2550.00
1280x720p
1920x1080i
1920x1080p
LAN
WIRELESS
CONTROL
HDMI OUTPUT
Horizontal
Frequency(KHz
)
31.4759
31.5060.00
44.9659.94
37.550.00
45.0060.00
33.7259.94
28.12550.00
33.7560.00
27.0024.00
33.7530.00
56.2550.00
67.43259.94
67.5060.00
RGB IN (PC)
/DVI IN
3
OPTICAL
(RGB/DVI)
DIGITAL
2
AUDIO IN
AUDIO OUT
1
2
YPBP
1
1
Vertical
Frequency(Hz
.94
VIDEO
)
RS-232
(
CONTROL&
VIDEO
R
EXTERNAL EQUIPMENT SETUP
L(MON
L
A
29
EXTERNAL EQUIPMENT SETUP
S
DVD SETUP
Component Connection
EXTERNAL EQUIPMENT SETUP
1. How to connect
Connect the video outputs (Y, P B, PR
1
DVD to the COMPONENT IN VIDEO 1, 2, or 3*
jacks on the TV.
Match the jack colors (Y = green, P
P
R = red
Connect the audio outputs of the DVD to the
2
COMPONENT IN AUDIO 1, 2, or 3* jacks on the
TV.
2. How to use
ꔛ
Turn on the DVD player, insert a DVD.
ꔛ
Select theComponent1, Component2, or
Component3*input source on the TV using the
INPUTbutton on the remote control.
ꔛ
Refer to the DVD player’s manual for operating
instructions.
* Component3: For LED LCD TV
Component Input ports
To get better picture quality, connect a DVD player to
the component input ports as shown below.
YLRPBP
)
of the
B = blue, and
)
.
RGB IN (PC)
/DVI IN
3
(RGB/DVI)
2
AUDIO IN
1
2
YPBP
1
1
OPTICAL
DIGITAL
AUDIO OUT
VIDEO
R
RS-232C IN
(
CONTROL&SERVICE)
L(MONO)
VIDEO
L R
R
AUDIO
2
AUDIO
AV IN 1
R
COMPONENT IN
For LED LCD TV
Component ports on the
YPBPR
TV
YPBPR
Video output ports
on DVD player
YB-YR-Y
YCb Cr
YPb Pr
USB IN 1 USB IN 2
COMPONENT IN3
AUDIO / Y PB PR
H/P
IN 4
AV IN2
VIDEO / AUDIO
1
2
YLRPBP
R
30
Loading...
+ 146 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.