LG 42CL40UA Users manual

Order Number : GETEC-C1-09-002
Test Report Number : GETEC-E3-09-002 FCC Class B Certification

APPENDIX H

: USER’S MANUAL

EUT Type: LCD TV/Monitor

FCC ID.: BEJ42CL40UA

Please read this manual carefully before operating
your set.

Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.

LCD TV
OWNER’S MANUAL

32LH40
37LH40
42LH40
47LH40
55LH40

37LH55
42LH55
47LH55
55LH55

32CL40
42CL40
47CL40

P/NO : SAC33601903 (0812-REV00)

www.lgusa.com / www.lg.ca

This product qualifies for ENERGY STAR in the “factory
default (Home mode)” setting and this is the setting in which
power savings will be achieved.

Changing the factory default picture setting or enabling other
features will increase power consumption that could exceed
the limits necessary to quality for Energy Star rating.

2

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the litera­ture accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

3

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers)that produce
heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com­bination to avoid injury from tip-over.

Unplug this apparatus during lighting storms
or when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power­supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.

1

2

3

4

5

7

8

6

9

10

4

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during
a thunder or lighting storm.

When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.

Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.

CAUTION concerning the Power Cord:
It is recommend that appliances be placed

upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.

Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.

Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).

GROUN D ING

Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC out­let). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.

DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The
plug must remain readily operable.

As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.

12

11

14

13

16

17

18

19

Power
Supply

Short-circuit

Breaker

15

5

ANTE N NAS
Outdoor ante n n a gr o unding

If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of over­head power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.

Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.

Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding
electrode.

Antenna grounding according to the
National Electrical Code, AN

SI/NFPA 70

Clea n ing

When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.

Movi ng

Make sure the product is turned off,
unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.

Venti l ation

Install your TV where there is proper ventila­tion. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.

If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the power
cord contact an authorized service center.

Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.

Keep the product away from direct sunlight.

For LCD TV

If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.

Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary dis­tortion effects on the screen.

20

23

24

25

26

27

21

22

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.

6

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 3

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stand Instruction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cable Management

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Attaching the TV to a Desk

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Kensington Security System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Securing the TV to the wall to prevent falling when
the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 24

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

USB Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Audio out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Turning On TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Initial Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Quick Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 48

- Add / Delete Channel (Manual Tuning)

. . . . . . 49

- Channel Editing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Channel List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Favorite Channel Setup / Favorite Channel List

. . 52

Brief Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Input Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

AV Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Simple Manual

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Key Lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Simplink

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

USB

Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 68

Picture Wizard

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Preset Picture Settings (Sound Mode)

. . . . . . . . . . . . . . 72

Manual Picture Adjustment - User Mode

. . . . . . . . . . 73

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 74

Expert Picture Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Energy Saving

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Power Indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Demo Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

7

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 82

Clear Voice II

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Preset Sound Setting (Sound Mode)

. . . . . . . . . . . . . . . . 84

Sound Setting Adjustment - User Mode

. . . . . . . . . . . 85

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Stereo/SAP Broadcasts Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 89

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

On-Screen Menus Language Selection

. . . . . . . . . . . . . . 91

Caption Mode

- Analog Broadcasting System Captions

. . . . . . . 92

- Digital Broadcasting System Captions

. . . . . . . . 93

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

PARENTAL CONTROL / RATINGS

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3

Downloadable Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

IR Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

External Control Through RS-232C

. . . . . . . . . . . . . . . . .116

Open Source License

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 2

8

FEATURE OF THIS TV

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN

HDMITM, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing."

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

CALIBRATE LIKE A PRO: Sophisticated and detailed
calibrations can be made through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an
ISF certified technician.

High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.

PREPARATION

9

ACCESSORIES

PREPARATION

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

Option Extras

* Wipe spots on the exterior only with

the polishing cloth.

* Do not wipe roughly when removing

stain. Excessive pressure may cause
scratch or discoloration.

Polishing Cloth

Copyright© 2007 LGE,
All Rights Reserved.

D-sub 15 pin Cable

1.5V 1.5V

Owner’s Manual Power Cord

Remote Control,

Batteries

IN
P

U

T

FAV

M
UT

E

T
V

S

T
B

P

OWER

Q

.ME

N

U

M

EN

U

A
V

MO

D

E

R
E
TU

RN

ENTER

V

O
L

C

H

123

456

78

0

9

FL
A

SH
B
K

P
A
G

E

D

V
D

V

C
R

CD Manual

When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.

Bolts for stand assembly

(Refer to P.14, 16)

Screw for stand fixing

(Refer to P.22)

x 4

(Except 47CL70) (Except 47CL70)

or

Protection Cover

This item is not included for all models.

PREPARATION

10

FRONT PANEL INFORMATION

PREPARATION

■

Image shown may differ from your TV.

CHANNEL (D,E)
Buttons

VOLUME (D,E)
Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

SPEAKER

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
(Can be adjusted

Powe r I n dica t or

in the

OPTION menu.

G

p.8 0

)

Remote Control
Sensor,
Intelligent Sensor

Adjusts picture accord­ing to the surrounding
conditions

Power Switch

"As long as this TV is connected to the
AC wall outlet, it is not disconnected
from the AC power source even if you
turn off this TV by SWITCH".

ON

OFF

32/37/42/47LH40, 37/42/47/55LH55

CH

VOL

ENTER

MENU

INPUT

PREPARATION

11

POWER Button

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using

Power Indicator

in

the OPTION menu.

G

p.80

)

CHANNEL ( , )
Buttons

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

Intelligent Sensor

Adjusts picture according to the surrounding
conditions

32/42/47CL40

Remote Control Sensor

CH

VOL

ENTER

MENU

INPUT

PREPARATION

12

BACK PANEL INFORMATION

PREPARATION

■

Image shown may differ from your TV.

( )

1 2 3

6 57

32/37/42/47LH40, 32/42/47CL40

9

R

1

8

2

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

IN 4

1

8

2

4

VIDEO

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/

CABLE IN

RGB IN (PC)

AV IN 1

COMPONENT IN

2

3

1

2

1

MONO

( )

AUDIOVIDEO

/DVI IN

LR

1 2 3

6 57

37/42/47/55LH55

4

AV IN 1

MONO

AUDIOVIDEO

LR

2

1

VIDEO

L R

AUDIO

COMPONENT IN

USB IN

/DVI IN

3

2

1

RGB IN (PC)

AUDIO IN

(RGB/DVI)

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/

CABLE IN

IN 4

AUDIO

L/ MONO

VIDEO

AV IN 2

PREPARATION

13

AV (Audio/Video) IN

Analog composite connection. Supports standard
definition video only (480i).

HDMI/DVI IN

Digital Connection.
Supports HD video and Digital audio. Doesn’t

support 480i.
Accepts DVI video using an adapter or HDMI to

DVI cable (not included).

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).

AUDIO IN (RGB/DVI)

1/8” headphone jack for analog PC audio input.

OPTICAL DIGITAL AUDIO OUT

Digital audio output for use with amps and home
theater systems.

Includes an optical connection.
Note: In standby mode, these ports do not work.

ANTENNA/CABLE IN

Connect over-the air signals to this jack.
Connect cable signals to this jack.

RS-232C IN (CONTROL & SERVICE) PORT

Used by third party devices.
This port is used for Service or Hotel mode.

COMPONENT IN

Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red

and white for audio.

USB INPUT

Used for viewing photos and listening to MP3s.

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

1

2

3

4

5

8

8

7

6

PREPARATION

14

STAND INSTRUCTION

(For 32/42/47CL40)

PREPARATION

Assemble the parts of the

STAND BO D Y

with

COVER BAS E

of the TV.

2

Assemble the TV as shown.

3

Fix the 4 bolts securely using the holes in the
back of the TV.

4

STAN D B ODY

COVER BAS E

Carefully place the TV screen side down on a cush­ioned surface to protect the screen from damage.

1

INSTALLATION (

Only 32/42CL40)

G

When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installa­tion). Do not over tighten.

NOTE

!

PREPARATION

15

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Loose the bolts from TV.

2

Detach the stand from TV.

3

After removing the stand, install the included
prote ction co v er

over the hole for the stand.

Press the

PROTECTION COVER

into the TV

until you hear it click.

PROTECTION COVER

PREPARATION

16

STAND INSTRUCTION

(For 32/37/42/47LH40, 37/42/47/55LH55)

PREPARATION

■

Image shown may differ from your TV.

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the TV as shown.

Fix the 4 bolts securely using the holes in the
back of the TV.

1

2

3

INSTALLATION

G

When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installa­tion). Do not over tighten.

NOTE

!

PREPARATION

17

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Loose the bolts from TV.

2

Detach the stand from TV.

3

After removing the stand, install the included
prote ction co v er

over the hole for the stand.

Press the

PROTECTION COVER

into the TV

until you hear it click.

PROTECTION COVER

PREPARATION

18

VESA WALL MOUNTING

PREPARATION

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest dealer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

G

Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric
shock.

CAUTION

G

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

G

Standard dimensions for wall mount kits are shown
in the table.

G

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

G

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to
the TV.

G

For wall mounts that do not comply with the VESA

standard screw specifications, the length of the
screws may differ depending on their specifica­tions.

G

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.

G

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

AA

BB

Model

VESA

(A *B)

Standard Screw Quantity

32LH40, 32CL40

37LH40, 37LH55
42LH40, 42LH55, 42CL40
47LH40, 47LH55, 47CL40

55LH40, 55LH55

200* 10 0

200* 200

600* 400

M4

M6

M8

4

4

4

PREPARATION

19

CABLE MANAGEMENT

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as
shown.

CABLE MANAGEMENT CLIP

1

2

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

For 32/42/47CL40

PREPARATION

20

CABLE MANAGEMENT

PREPARATION

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as
shown.

CABLE MANAGEMENT CLIP

1

2

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

For 32/42/47/55LH40, 37/42/47/55LH55

PREPARATION

21

DESKTOP PEDESTAL INSTALLATION

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

■

Image shown may differ from your TV.

4 inches

G

Ensure adequate ventilation by following the clearance recommendations.

G

Do not mount near or above any type of heat source.

CAUTION

4 inches

4 inches

4 inches

PREPARATION

22

ATTACHING THE TV TO A DESK

PREPARATION

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.

G

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

KENSINGTON SECURITY SYSTEM

■

This feature is not available for all models.

- The TV is equipped with a Kensington Security System connector on
the back panel. Connect the Kensington Security System cable as
shown below.

- For the detailed installation and use of the Kensington Security

System, refer to the user’s guide provided with the Kensington
Security System.

For further information, contact

http: / /www. k ensing t on.co m

,
the internet homepage of the Kensington company. Kensington sells
security systems for expensive electronic equipment such as note­book PCs and LCD projectors.

NOTE: The Kensington Security System is an optional accessory.

PREPARATION

23

SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.

■

You should purchase necessary components to prevent TV from falling off of the stand.

■

Image shown may differ from your TV.

G

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.

G

To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

NOTE

!

PREPARATION

24

ANTENNA OR CABLE CONNECTION

PREPARATION

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wa ll
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire
when connecting the antenna.

Copper Wire

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA/

CABLE IN

ANTENNA/

CABLE IN

EXTERNAL EQUIPMENT SETUP

25

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.

Component Connection

1. How to connect

Connect the video outputs (Y, PB, PR

)

of the digital set-

top box to the

COMPO N ENT IN V I DEO 1

jacks on

the TV. Match the jack colors (Y = green, P

B = blue, and

P

R = red).

Connect the audio output of the digital set-top box to
the

COMPO N ENT IN AUDI O 1

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box. operation

)

■

Select the

Comp o nent 1

input source on the TV using the

INP UT

button on the remote control.

■

If connected to

COMP O NENT IN 2

input, select the

Comp o nent 2

input source on the TV.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

Y, CB/PB, CR/P

R

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

1920x1080p

Signal

480i

480p

720p

10 8 0 i

10 8 0 p

Component

Yes

Yes

Yes

Yes

Yes

HDMI

No

Yes

Yes

Yes

Yes

AV IN 1

2

3

1

MONO

( )

AUDIOVIDEO L R

/DVI IN

VIDEO

AUDIO

L R

COMPONENT IN

2

1

Y L RPBP

R

1

2

EXTERNAL EQUIPMENT SETUP

26

EXTERNAL EQUIPMENT SETUP

HDMI Connection

Connect the digital set-top box to

HDMI/D V I I N 1

,

2, 3

, or

4

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HDMI1, HDMI2, HDMI3

, or

HDMI4

input

source on the TV using the

INPUT

button on the remote

control.

2

1

HDMI-DTV

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.939

67.50 60.00

Resolution

720x480p

1280x720p

1920x1080i

1920x1080p

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

O

A

C

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOVIDEO L R

2

3

1

/DVI IN

HDMI OUTPUT

1

G

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

NOTE

!

EXTERNAL EQUIPMENT SETUP

27

DVI to HDMI Connection

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIG

AUDIO OU

ANTENNA

CABLE IN

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOLR

2

3

1

/DVI IN

AUDIO IN

(RGB/DVI)

L R

DVI OUTPUT

AUDIO

1

2

G

A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio
connection is necessary.

NOTE

!

Connect the DVI output of the digital set-top box to
the

HDMI / DVI IN 1, 2, 3

, or 4jack on the TV.

Connect the digital set-top box audio output to the
AUD I O

(

RGB / DVI

)

jack on the TV.

1. How to connect

2. How to use

■

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HDMI1, HDMI2, HDMI3

, or

HDMI4

input

source on the TV using the

INPUT

button on the remote

control.

2

1

EXTERNAL EQUIPMENT SETUP

28

DVD SETUP

EXTERNAL EQUIPMENT SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBP

R

Video output ports

on DVD player

Y

Y

Y

Y

P

B

B-Y

Cb

Pb

P

R

R-Y

Cr

Pr

Connect the video outputs (Y, PB, PR

)

of the DVD to the

COMPO N ENT IN VIDE O 1

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and PR = red

)

.

Connect the audio outputs of the DVD to the
COMPO N ENT IN AUDI O 1

jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

Comp o nen t1

input source on the TV using

the

INP UT

button on the remote control.

■

If connected to

COMP O NENT IN 2

input, select the

Comp o nent 2

input source on the TV.

■

Refer to the DVD player's manual for operating instructions.

2

1

AV IN 1

2

3

1

MONO

( )

AUDIOVIDEO L R

/DVI

VIDEO

AUDIO

L R

COMPONENT IN

2

1

Y L RPBP

R

1 2

EXTERNAL EQUIPMENT SETUP

29

Composite (RCA) Connection

VIDEO

AUDIO

L R

COMPONENT IN

2

3

1

2

1

/DVI IN

AV IN 1

MONO

( )

AUDIOVIDEO LR

L R

VIDEO

AUDIO

1

2

HDMI Connection

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

OP

A

AN

C

RGB IN (PC)

AV IN 1

1

MONO

( )

AUDIOVIDEO L R

2

3

1

/DVI IN

HDMI OUTPUT

1

Connect the

AUD IO/VID EO

jacks between TV and
DVD. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

AV 1

or

AV 2

input source on the TV using the

INP UT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

1

Connect the HDMI output of the DVD to the
HDMI / DVI IN 1, 2, 3

or 4jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HDMI1, HDMI2, HDMI3

, or

HDMI4

input

source on the TV using the

INP UT

button on the remote

control.

■

Refer to the DVD player's manual for operating instructions.

2

1

G

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

NOTE

!

EXTERNAL EQUIPMENT SETUP

30

VCR SETUP

EXTERNAL EQUIPMENT SETUP

Antenna Connection

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

Connect the RF antenna out socket of the
VCR to the

ANTE N NA/CA B LE IN

sock-

et on the TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

RGB IN (PC)

ANTENNA/

CABLE IN

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

AUDIO

Wall Jack

Antenna

1

2

EXTERNAL EQUIPMENT SETUP

31

Composite (RCA) Connection

G

If you have a mono VCR, connect the audio cable from
the VCR to the

AUDI O L / MONO

jack of the TV.

NOTE

!

VIDEO

AUDIO

L R

COMPONENT IN

2

3

1

2

1

/DVI

AV IN 1

MONO

( )

AUDIOVIDEO LR

L R

S-VIDEO VIDEO

AUDIO

OUTPUT

SWITCH

ANT IN

ANT OUT

1

Connect the

AUD IO/VID EO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR.
(

Refer to the VCR owner’s manual.

)

■

Select the

AV 1

input source on the TV using the

INP UT

button on the remote control.

■

If connected to

AV I N 2

, select

AV2

input source on the TV.

1

EXTERNAL EQUIPMENT SETUP

32

OTHER A/V SOURCE SETUP

EXTERNAL EQUIPMENT SETUP

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

IN 4

L R

VIDEO

Camcorder

Video Game Set

Connect the

AUDIO/VIDEO

jacks
between TV and external equipment.
Match the jack colors

.

(

Video = yellow, Audio Left = white, and

Audio Right = red

)

1. How to connect

2. How to use

■

Select the

AV 2

input source on the TV using

the

INP UT

button on the remote control.

■

If connected to

AV I N 1

input, select the

AV 1

input source on the TV.

■

Operate the corresponding external equipment.

1

1

EXTERNAL EQUIPMENT SETUP

33

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

RS-232C IN

(

CONTROL&SERVICE)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/
CABLE IN

2

3

1

R

/DVI IN

AUDIO IN

(RGB/DVI)

RGB IN (PC)

RGB OUTPUT

AUDIO

1

2

Connect the VGA output of the PC to the

RGB I N

(

P C

)

jack on the TV.

Connect the PC audio output to the

AUDIO I N

(

RGB/D V I

)

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

RGB - PC

input source on the TV using the

INP UT

button on the remote control.

2

1

EXTERNAL EQUIPMENT SETUP

34

EXTERNAL EQUIPMENT SETUP

NOTES

!

DVI to HDMI Connection

AUDIO

L R

RS-232C IN

(

CONTROL&SERVICE)

OP

A

A

C

RGB IN (PC)

AV IN 1

MONO

( )

AUDIOVIDEO L R

AUDIO IN

(RGB/DVI)

2

3

1

/DVI IN

AUDIO

DVI OUTPUT

1

2

Connect the DVI output of the PC to the

HDMI / DVI

IN 1, 2, 3

, or 4jack on the TV.

Connect the PC audio output to the

AUDI O I N

(RGB /DVI )

jack on the TV.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select the

HDMI1, HDMI2, HDMI3

, or

HDMI4

input

source on the TV using the

INP UT

button on the remote

control.

2

1

G

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.

NOTE

!

G

To get the the best picture quality, adjust the PC
graphics card to 1920x1080.

G

Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.

G

In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or bright­ness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.

G

Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.

G

The synchronization input form for Horizontal and
Vertical frequencies is separate.

G

Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.

G

If there are overscan in HDMI-PC 1920x1080,
change aspect ratio to

Just sca n

.

G

The TV provides EDID data to the PC system
with a DDC protocol. DDC protocol is preset for
RGB (Analog RGB), HDMI (Digital RGB) mode.

EXTERNAL EQUIPMENT SETUP

35

Supported Display Specifications (RGB-PC, HDMI-PC)

Resolution

720x400

640x350

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.09

31.469 70.08

31.469 59.94

35.156 56.25

37.879 60.31

48.363 60.00

56.476 70.06

47.776 59.87

63.981 60.02

47.712 60.015

75.00 60.00

66.587 59.934

67.5 60.00

640x480

800x600

1024x768

1280x768

1280x1024

1360x768

1600x1200

1920x1080

RGB-PC

1920x1080

HDMI-PC

EXTERNAL EQUIPMENT SETUP

40

USB CONNECTION

EXTERNAL EQUIPMENT SETUP

USB IN

IN 4

AV IN 2

L/ MONO

R

AUDIO

VIDEO

Memory Key

Connect the USB device to the

USB I N

jack on the side

of TV.

1. How to connect

1

2. How to use

■

After connecting the

USB I N

jack, you use the USB func-

tion. (

G

p.60

)

1

or

EXTERNAL EQUIPMENT SETUP

41

AUDIO OUT CONNECTION

Send the TV’s audio to external audio equipment via the Audio Output port.

If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).

RS-232C IN

(

CONTROL&SERVICE)

AUDIO IN

(RGB/DVI)

ANTENNA/

CABLE IN

RGB IN (PC)

/DVI IN

OPTICAL DIGITAL

AUDIO OUT

1

2

G

When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (

G

p.8 7

)

NOTE

!

G

Do not look into the optical output port. Looking at the
laser beam may damage your vision.

G

Block the SPDIF out (optical) about the contents with
ACP (Audio Copy Protection) function.

CAUTION

Connect one end of the optical or coaxial cable to the TV
port of

OPTI C AL DIGITAL AUDIO OUT

.

Connect the other end of the optical cable to the digital
audio input on the audio equipment.

Set the “TV Speaker option - Off” in the AUDIO menu. (

G

p.87

). See the external audio equipment instruction manu-

al for operation.

1. How to connect

2

3

1

WATCHING TV / CHANNEL CONTROL

42

REMOTE CONTROL FUNCTIONS

WATCHING TV / CHANNEL CONTROL

When using the remote control, aim it at the remote control sensor on the TV.

FAV

MUTE

MARK

RATIO

SLEEP

POWER

Q. MENU MENU

AV MODERETURN

VOL

CH

123

456

7809

FLASHBK

P
A
G
E

INPUT

ENERGY SAVING

INFO

LIST

ENTER

RATIO

SLEEP

POWER

INPUT

ENERGY SAVING

Q.MENU

MENU

SIMPLINK

— (DASH)

LIST

FLASHBK

Change the aspect ratio.

G

p.68

Select the amount of time before your TV turns off auto­matically.

G

p.98

Turns your TV on or off.

Rotates through inputs.
Also switches the TV on from standby.

G

p.54

Adjusts the Energy Saving.

G

p.78

Opens the list of Quick Menu options.

G

p.47

Displays the main menu.
Clear all on-screen displays and return to TV viewing from

any menu.

See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu

appears at the screen.

G

p.58-59

Used to enter a program number for multiple program
channels such as 2-1, 2-2, etc.

Displays the channle table.

G

p.51

Tunes to the last channel viewed.

Controls video cassette recorders or DVD players.
Controls USB menu (PHOTO LIST and MUSIC LIST.)
Controls the SIMPLINK compatible devices.

NUMBER button

VCR, USB,

SIMPLINK

Control buttons

WATCHING TV / CHANNEL CONTROL

43

THUMBSTICK

(Up/Down/Left

Right/ENTER)

RETURN

INFO

AV MODE

VOLUME UP

/DOWN

FAV

MARK

MUTE

CHANNEL

UP/DOWN

PAGE

UP/DOWN

Navigates the on-screen menus and adjusts the system settings to your preference.

Allows the user to move return one step in an interactive application or other user interaction
function.

Displays channel information at the top of the screen.

G

p.53

Toggles through preset Video and Audio modes.

G

p.56

Increase/decrease the sound level.

Scroll through the programmed Favorite channels.

G

p.52

Select the input to apply the Picture Wizard settings.

G

p.71

Use to mark or unmark a photo/music

G

p.62, 66

Switchs the sound on or off.

G

p.44

Changes the channel.

Moves from one full set of screen information to the next one.

■

Open the battery compartment cover on the back side and
install the batteries matching correct polarity.

■

Install two 1.5V AAA batteries. Don’t mix old or used bat­teries with new ones.

■

Close cover.

Installing Batteries

WATCHING TV / CHANNEL CONTROL

44

TURNING ON THE TV

WATCHING TV / CHANNEL CONTROL

NOTE

!

G

If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

G

If you do not complete the

Initia l se t t ing

, it will appear whenever the TV is switched on until the

Initia l set t ing

procedure is completed.

G

If this TV is unplugged once or turn off with the power switch on the TV, reset the Time function.

First, connect power cord correctly and switch the main power on TV front.
At this moment, the TV switches to standby mode.

■

In standby mode to turn TV on, press the ,

INPUT,CH (

D E

or

)

button on the TV or press

the

POWER, INPUT, TV, CH(

or ),

Number (0~9)

button on the remote control.

Select the viewing source by using the

INPUT

button on the remote control.

■

This TV is programmed to remember which power state it was last set to, even if the power cord is out.

When finished using the TV, press the

POWER

button on the remote control. The TV reverts to standby

mode.

1

2

3

Press the

CH (

or )or

NUMBER

buttons to select a channel number.

1

VOLUME ADJUSTMENT

CHANNEL SELECTION

Press the

VOL (+

or -)button to adjust the volume.

If you want to switch the sound off, press the

MUTE

button.

You can cancel the Mute function by pressing the

MUTE

or

VOL (+

or

-)

button.

Adjust the volume to suit your personal preference.

1

2

3

ENTRY MODES

USB

60

USB

Precautions when using the USB device

G

Only a USB storage device is recognizable.

G

If the USB storage device is connected through a
USB hub, the device is not recognizable.

G

A USB storage device using an automatic recogni­tion program may not be recognized.

G

A USB storage device which uses its own driver
may not be recognized.

G

USB multi-card reader or USB hard drive may not
operate smoothly or may not operate at all.

G

The recognition speed of a USB storage device
may depend on each device.

G

Please do not turn off the TV or unplug the USB
device when the connected USB storage device is
working. When such device is suddenly separated
or unplugged, the stored files or the USB storage
device may be damaged.

G

Only use a USB storage device which has normal
music files or image files.

G

Please use only a USB storage device which was
formatted as a FAT or NTFS file system provided
with the Windows operating system. In case of a

storage device formatted as a different utility pro­gram which is not supported by Windows, it may
not be recognized.

G

Please connect power to a USB storage device
which requires an external power supply. If not,
the device may not be recognized.

G

Please connect a USB storage device with cable is
offered by USB maker. If connected with cable is
not offered by USB maker or an excessively long
cable, the device may not be recognized.

G

Some USB storage devices may not be supported
or operate properly.

G

Please backup important files because data on
USB device may be damaged. Data management is
consumer's responsibility and as a result, the man­ufacturer does not cover data damage.

When removing the USB device

Connect the USB device to the

USB I N

jacks on the side of TV.

3

Select

Phot o L i st orMus ic L is t

.

1

USB IN

IN 4

Memory Key

Photo List Music List

Select

USB De v ice

.

Select

Eje ct

.

Select the

USB De v ice

menu before removing the

USB device.

2

ENTER

1

Q. MENU

2

ENTER

■

It doesn’t support USB HDD

■

This TV supports JPG and MP3 files.

When you connect a USB device, this pop up menu is displayed automatically.
When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu.
In USB device, you can not add a new folder or delete the existing folder.

USB

62

USB

Photo Selection and Popup Menu

Select the target folder or drive.

Select the desired photos.

2

Show the Popup menu.

3

1

■

Use the

CH

button to navigation in the

photo page.

■

Use the

MARK

button to mark or unmark a
photo. When one or more photos are marked,
you can view individual photos or a slide show
of the marked photos. If no photos are marked,
you can view all photos individually or all pho­tos in the folder in a slide show.

4

Select the desired Popup menu.

ENTER

ENTER

ENTER

When you select a file (not folder), this PopUp
menu is displayed.

G

View

: Display the selected item.

G

Mark All

: Mark all photos on the screen.

G

Unma r k All

: Deselect all marked photos.

G

Del e te

: Delete the selected photo item.

G

Clo se

: Close the pop-up menu.

USB Device

Page 2/3

No Marked

Photo List

Up Folder

Free Space 150MB

1366x768, 125KB

KY101

06/10/2008

KY102 04/03/2008

JMJ001 01/01/2000

JMJ002 06/15/2008

JMJ003 04/03/2008

JMJ004 02/18/2008

KY103 03/30/2008

KY104 06/19/2008

KY105 01/31/2008

JMJ005 05/13/2008

JMJ006 05/26/2008

JMJ007 02/18/2008

JMJ008 02/18/2008

Up Folder

USB Device

Page 2/3

No Marked

Photo List

Up Folder

Free Space 150MB

1366x768, 125KB

KY101

06/10/2008

KY102 04/03/2008

JMJ001 01/01/2000

JMJ002 06/15/2008

JMJ003 04/03/2008

JMJ004 02/18/2008

KY103 03/30/2008

KY104 06/19/2008

KY105 01/31/2008

JMJ005 05/13/2008

JMJ006 05/26/2008

JMJ007 02/18/2008

JMJ008 02/18/2008

Up Folder

Drive1

Drive1

JMJ001

JMJ001

1366x768, 125KB

View

Mark All

Delete

Close

Navigation Page Change Mark Exit

CH

MARK

Popup Menu

Navigation Page Change Mark Exit

CH

MARK

Popup Menu

USB

64

USB

Select the

Sideshow, BGM

,

(Rotate)

,

Dele te,Option

, or

Hide.

■

Use button to select the previous or
next photo.

■

Use button to select and control
the menu on the full-sized screen.

ENTER

6

NOTE

!

G

This TV will not be able to decode
most JPG images saved using the
Progressive option.

1/17

Sideshow BGM D elete Option Hide

Press

F G

to set the time interval between slides.

Slide Speed

Fast

Cancel

...

Music Album

Enter

G

Slid e S h ow

: Selected photos are displayed during the
slide show. If no photo is selected, all photos in the cur­rent folder are displayed during slide show.

■

Set the time interval of the slide show in

Opt i on

.

G

BG M

: Listen to music while viewing photos in full size.

■

Set the BGM device and album in

Opt i on

.

G

(Rot ate)

: Rotate photos.

■

Rotates the photo 90°, 18 0 °, 270°, 360° clockwise.

G

Del e te

: Delete photos.

G

Opt i on

: Set values for

Slid e S peed

and

Mus ic

Alb um

.

■

Use button and

ENT ER

button to set values.

Then go to and press

ENT ER

to save the set-

tings.

■

You cannot change

Musi c Albu m

while BGM is

playing.

G

Hid e

: Hide the menu on the full-sized screen.

■

To see the menu again on the full-sized screen, press
ENT E R

button to display.

USB

66

USB

Music Selection and Popup Menu

■

Use the

CH

button to navigation in

the music page.

■

Use

MAR K

button to mark or unmark a music
file. If no music is marked, all the music in the
folder will be played in sequence. When one or
more music files are marked, the marked music
files will be played in sequence. If you want to
listen to only one song repeatedly, just mark
that one file and play.

Up to 6 music titles are listed per page.

Select the target folder or drive.

Select the desired musics.

Show the Popup menu.

Select the desired Popup menu.

2

3

1

4

ENTER

ENTER

ENTER

5

RETURN

Return to TV viewing

USB Device

Page 1/1

No Marked

Music List

Up Folder

Free Space 150MB

A

00:00 / 04:16

Drive1

Arirang

DurationTitle

Up Folder

Good Bye

Arirang

USB Device

Page 1/1

No Marked

Music List

Up Folder

Free Space 150MB

A

00:00 / 04:16

Drive1

Arirang

DurationTitle

Good Bye

Arirang

05:30

04:12

Navigation Page Change Mark Exit

CH

MARK

Popup Menu

Navigation Page Change Mark Exit

CH

MARK

Popup Menu

3945 KB
128 Kbps

Play

Play with Photo

Mark All

Delete

Cancel

G

Pla y

(During stop): Play the selected music.

Once a song finishes playing, the next selected
one will be played. When there are no selected
musics to play, the next one in the current fold­er will be played. If you go to a different folder
and press the

ENT ER

button, the current

music in playback will stop.

G

Play Mar k ed

: Play the selected musics. Once
a music finishes playing, the next selected one
will be played automatically.

G

Stop Pl ay

(During playback): Stop the play-

ing musics.

G

Play wi th Ph o to

: Start playing the selected

musics and then move to the Photo List.

G

Mark A l l

: Mark all musics in the folder.

G

Unma r k All

: Deselect all marked music.

G

Del e te

: Delete the selected music.

G

Clo se

: Close the pop-up menu.

USB

67

■

The play information box (as shown below) will automatically
move across the screen when there is no user input to pre­vent a fixed image remaining on the screen for a extended
period of time.

NOTE

!

G

When music is playing, is displayed in front of the music play time.

G

A damaged or corrupted music file that does not play displays 00:00 as the play time.

G

Music files with copy-protection will not play.

G

Press

ENT ER

, A, or

RET U RN

button to stop the screen saver.

G

This TV can not play music files less than 16 Kbytes.

PICTURE CONTROL

69

16:9

Adjust the picture horizontally, in a linear pro­portion to fill the entire screen.

Just Scan

Normally the edges of video signals are cropped
1-2%. Just Scan turns off this cropping and
shows the complete video.

Notes: If there is noise on the edges of the original
signal, it will be visible when Just Scan is activated.

Just S c an

operates only in
DTV/CADTV/Component/HDMI-DTV/DVI-DTV
(720p/1080i/1080p) input source.

Set by program

Selects the proper picture proportion to match
the source’s image.

4:3

Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.

Zoom

Choose Zoom when you want to view the picture
without any alteration. However, the top and
bottom portions of the picture will be cropped.

■

When adjusting in Q.MENU menu,
a.

F

or Gbutton: Adjust enlarge proportion

of Zoom.

b.

D

or Ebutton: Move the screen.

Cinema Zoom

Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.

Note: When enlarging or reducing the picture,
the image may become distorted.

■

F

or Gbutton: Adjust enlarge proportion of

Cinema Zoom. The adjustment range is 1-16.

■

D

or Ebutton: Move the screen.

(4:3 4:3)

(16:9 16:9)

PICTURE CONTROL

76

PICTURE CONTROL

■

Set to warm to enhance hotter colors such as red, or set to cool to see less intense
colors with more blue.

■

Adjusts the contrast to keep it at the best level according to the brightness of the
screen. The resolution of gradation is improved by making bright parts brighter and
dark parts darker. This feature refers to dynamic contrast, and enhances the feeling
of presence that contrast controls are intended to give by using dimming and other
input signals.

■

Adjusts screen colours so that they look livelier, richer and clearer. This feature
enhances hue, saturation and luminance so that red, blue, green and white look
more vivid.

■

Reduces screen noise without compromising video quality. This feature is also used to
reduce recursive noise.

■

Set the gradient curve according to the relationship between input and output of
the video signal. Calibrate the linear characteristics of the gradient curve between
input signal voltage to output.

■

You can adjust brightness of dark area and middle gray level area of the picture.

•

Low : Make dark and middle gray level area of the picture brighten.

• Medium: Express original picture gradation.

• High: Make dark and middle gray level area of the picture darken.

Low: The reflection of the screen gets darker.
High: The reflection of the screen gets brighter.
Auto: Realizing the black level of the screen and set it to High or Low automatically.

■

Makes dark parts on the screen look darker.

■

This feature is disable in DTV and RGB-PC mode.

■

Adjust the brightness of the screen to prevent the screen from being too bright.
Dims extremely bright pictures.

■

This feature is disable in “

Pictu r e M ode-V i vid, Cin e ma

”.

■

Makes video clips recorded in film look more natural.

■

When you operate Real Cinema (3:2 Pull-Down Mode or Cinema Correction Mode),
the TV will adjust 24 fps video from movies to 30 fps video for display.

■

This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV,
Component 480i/1080i, and HDMI 1080i mode.

Standard: Mode to realize original color irrelevant from the display characteristics of
the color space according to the standard of input signal.

Wide: Mode to use and set the rich color area of the display.

■

Maximize the utilization for color area that can be expressed.

■

This feature is disabled in “

Pictu r e M ode-V i vid, Spo rt

”.

■

Show clearer and distinctive yet natural corners of the video. Emphasizes the frames
of the video without over peaking.

Dynamic Contrast

Dynamic Color

Noise Reduction

Gamma

Black Level

Eye Care

Real Cinema

Color Gamut

Edge Enhancer

Color Temperature

PICTURE CONTROL

77

■

Convert the color of a different video to HD color. This function is set for SD video
(BT-601) and HD video (BT-709) color format.

■

This is the function to adjust the overall color of the screen to the feeling you want.

a. Method : 2 Points

- Pattern: Inner, Outer

- Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50.

b. Method : 10 Point IRE

- Pattern: Inner, Outer

- IRE (Institute of Radio Engineers) is the unit to display the size of the video signal

and can be set among 10, 20, 30 - 100. You can adjust Red, Green or Blue accord­ing to each setting.

- Luminance: Automatically adjusted depending on IRE value.

- Red/Green/Blue: The adjustment range is -50 - +50.

■

As the tool used by the experts to make adjustments by using the test patterns, this
does not affect other colors but can be used to selectively adjust the 6 color areas
(Red/Green/Blue/Cyan/Mgt/Yellow).

Color difference may not be distinctive even when you make the adjustments for the
general video.

Adjusts Red/Green/Blue/Yellow/Cyan, Magenta.

- Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is -50 - +50.

- Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -50 - +50.

- This feature is disable in RGB-PC and HDMI (PC) mode.

*This feature is not available for all models.

■

As the technology to reduce the power consumption while keeping the same bright­ness, this has the effect of reducing power consumption, improvement in contrast
and light source etc.

White Balance

Color Management

OPC

Color Standard

■

TruMotion120Hz provides even better quality for movies than 3:2 Pull-Down con­versions.

■

TruMotion120Hz means the panel supports faster frame rates that normal panels
which makes for smoother motion in video. TruMotion LCD models support 120Hz
instead of 60Hz. This means twice the information on the screen in the same
amount of time and easier film conversions (120 is equally divisible by 24, so no
interpretations or double frames are needed).

■

TruMotion120Hz works with all inputs except PC mode.

• If you enable "TruMotion 100HZ", noise may appear on the screen.

• If this occurs, set "TruMotion 100HZ" to "Off".

TruMotion 120Hz/240Hz

■

This is the pattern necessary for expert adjustment.

Expert Pattern

■

This is the function to filter only the specific color area of the video by adjusting
the RGB LUT of the output terminal.

You can use the RGB filter to accurately set the color concentration and color

Color Filter

■

This is the function to express richer color.

xvYCC

PARENTAL CONTROL / RATING

102

CHANNEL BLOCKING

PARENTAL CONTROL / RATINGS

Enter

Move

LOCK

Lock System : Off

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Downloadable Rating

Input Block

Select

Block Chan n el

.

Select a channel to block or unblock.

4

3

ENTER

Block or unblock a channel.

5

Blocks any channels that you do not want to watch or that you do not want your children to watch.

Select

LO C K

.

1

MENU

ENTER

Input the password.

2

1

456

7809

23

6

MENU

Return to the previous menu.

RETURN

Return to TV viewing.

Ch. Change

Page Change

CH

Navigation

Previous

Block/Unblock

PARENTAL CONTROL / RATING

105

TV Rating General

-

For USA only

Based on the ratings, blocks certain TV programs that you and your family do not want to view.

Enter

Move

LOCK

Lock System : Off

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Downloadable Rating

Input Block

Select

TV R ating-G e neral

.

Select

Ag e, Dia l ogu e, Lan g uag e

,

Se x

or

Viol e nce

.

4

3

ENTER

Select block options.

5

ENTER

Enter

Move

LOCK

Lock System : Off

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Downloadable Rating

Input Block

■

Age (applies to TV-G,TV-PG,TV-14,TV­MA).

■

Dialogue-sexual dialogue (applies to
TV-PG,TV-14).

■

Language-adult language (applies to
TV-PG, TV-14, TV-MA).

■

Sex-sexual situations (applies to TV-PG,
TV-14, TV-MA).

■

Violence (applies to TV-PG, TV-14, TV­MA).

Close

Age

Dialogue

Language

Sex

Violence

Select

LO C K

.

1

MENU

ENTER

Input the password.

2

1

456

7809

23

6

RETURN

Return to the previous menu.

MENU

Return to TV viewing.

APPENDIX

110

APPENDIX

TROUBLESHOOTING

The TV does not turn on.

The video does not work.

No picture &No sound

No or poor color

or poor picture

Poor reception on

some channels

Lines or streaks

in pictures

No picture

when connecting HDMI

Horizontal/vertical bars

or picture shaking

Picture appears slowly

after switching on

The remote control

doesn’t work

Power is suddenly

turned off

■

Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.

■

Ensure that the batteries are installed with correct polarity (+ to +, - to -).

■

Ensure that the correct remote operating mode is set: TV, VCR etc.

■

Install new batteries.

■

Is the sleep timer set?

■

Check the power control settings. Power interrupted.

■

Check whether the product is turned on.

■

Try another channel. The problem may be with the broadcast.

■

Is the power cord inserted into wall power outlet?

■

Check your antenna direction and/or location.

■

Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.

■

This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.

■

Adjust Color in menu option.

■

Keep a sufficient distance between the product and the VCR.

■

Try another channel. The problem may be with the broadcast.

■

Are the video cables installed properly?

■

Activate any function to restore the brightness of the picture.

■

Check for local interference such as an electrical appliance or power tool.

■

Station or cable product experiencing problems, tune to another station.

■

Station signal is weak, reorient antenna to receive weaker station.

■

Check for sources of possible interference.

■

Check antenna (Change the direction of the antenna).

■

Check HDMI cable over version 1.3.

The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen
display. In this case use the latest cables that support HDMI version 1.3.

APPENDIX

111

There is a problem in PC mode. (Only PC mode applied)

■

Adjust resolution, horizontal frequency, or vertical frequency.

■

Check the input source.

■

Work the Auto configure or adjust clock, phase, or H/V position. (Option)

■

Check the signal cable.

■

Reinstall the PC video card.

The signal is out of range

Screen color is unstable

or single color

Vertical bar or stripe on

background &

Horizontal Noise &

Incorrect position

Picture OK & No sound

Unusual sound from

inside the product

No sound

when connecting

HDMI/USB

No output from one

of the speakers

The audio does not work.

■

Press the VOL or VOLUME button.

■

Sound muted? Press MUTE button.

■

Try another channel. The problem may be with the broadcast.

■

Are the audio cables installed properly?

■

Adjust Balance in menu option.

■

A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product.

■

Check HDMI cable over version 1.3.

■

Check USB cable over version 2.0.

■

Use normal MP3 file.

*This feature is not available for all models.

APPENDIX

112

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.

Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.

Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the Cabinet

■

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

■

Please be sure not to use a wet cloth.

Extended Absence

G

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

CAUTION

2

1

APPENDIX

113

PRODUCT SPECIFICATIONS

■

The specifications shown above may be changed without prior notice for quality improvement.

MODELS

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 104°F (0 ~ 40°C)

Less than 80%

-4 ~ 140°F (-20 ~ 60°C)

Less than 85%

Dimensions
(Width x Height
x Depth)

Weight

Power requirement
Television System
Program Coverage
External Antenna Impedance

Environment
condition

With stand

Without stand

With stand
Without stand

Operating Temperature
Operating Humidity

Storage Temperature
Storage Humidity

32LH40

(32LH40-UA)

37LH40

(37LH40-UA)

42LH40

(42LH40-UA)

31.6 x 23.0 x 8.8 inches

804.4 x 586.3 x 223.8 mm

31.6 x 20.8 x 3.1 inches

804.4 x 529.2 x 81.0 mm

26.8 pounds / 12.2 kg

24.0 pounds / 10.9 kg

36.6x 27.8 x 14.8 inches
929 x 706.9x 374.7mm

36.6x 26.1 x 3.9 inches

929 x 665x 98.7mm

46.3 pounds / 21.2 kg

39.9 pounds / 18.1 kg

40.7 x 23.8 x 11.6 inches

1036.0 x 721.3 x 296.2 mm

40.7 x 25.8 x 3.5 inches

1036.0 x 655.4 x 89.8 mm

40.3 pounds / 18.3 kg

36.3 pounds / 16.5 kg

Dimensions
(Width x Height
x Depth)

Weight

With stand

Without stand

With stand
Without stand

1156.2 x 813.1 x 342.9 mm

45.6 x 32.0 x 13.5 inches

1156.2 x 739.2 x 103.0 mm

45.6 x 29.1 x 4.1 inches

64.4

pounds

/ 29.2 kg

54.3

pounds

/ 24.6 kg

MODELS

47LH40

(47LH40-UA)

63.4 x 37.1 x 12.5 inches

1612.0 x 944.2 x 320.0 mm

63.4 x 34.5 x 5.6 inches

1612.0 x 878.0 x 143.0 mm

160.7

pounds

/ 72.9 kg

130.9

pounds

/ 59.4 kg

55LH40

(55LH40-UA)

Dimensions
(Width x Height
x Depth)

Weight

With stand

Without stand

With stand
Without stand

32.0 x 23.5 x 91. inches

813.8 x 598.8 x 231.9 mm

32.0 x 21.2 x 3.1 inches

813.8 x 540.4 x 78.9 mm

28.4 pounds / 12.9 kg

25.1 pounds / 11.4 kg

40.7 x 28.9 x 11.5 inches

1034.0 x 735.0 x 294.0 mm

40.7 x 26.1 x 3.5 inches

1034.0 x 663.0 x 91.0 mm

54.0 pounds / 24.5 kg

48.5 pounds / 22.0 kg

45.5 x 32.0 x 13.5 inches

1156.2 x 813.1 x 342.9 mm

45.5 x 29.1 x 4.0 inches

1156.2 x 739.2 x 103.0 mm

64.3 pounds / 29.2 kg

54.2 pounds / 24.6 kg

MODELS

32CL40

(32CL40-UA)

42CL40

(42CL40-UA)

47CL40

(47CL40-UA)

APPENDIX

114

APPENDIX

■

The specifications shown above may be changed without prior notice for quality improvement.

MODELS

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 104°F (0 ~ 40°C)

Less than 80%

-4 ~ 140°F (-20 ~ 60°C)

Less than 85%

Dimensions
(Width x Height
x Depth)

Weight

Power requirement
Television System
Program Coverage
External Antenna Impedance

Environment
condition

With stand

Without stand

With stand
Without stand

Operating Temperature
Operating Humidity

Storage Temperature
Storage Humidity

37LH55

(37LH55-UA)

42LH55

(42LH55-UA)

36.6x 27.8 x 14.8 inches
929 x 706.9x 374.7mm

36.6x 26.1 x 3.9 inches

929 x 665x 98.7mm

46.3 pound / 21.2 kg

39.9 pound / 18.1 kg

41.5x 28.3 x 11.7 inches

1052.2 x 719.1 x 296.2mm

41.5 x 25.9 x 3.6 inches

1052.2 x 657.4 x 90.8mm

40.4 pound / 18.3 kg

36.4 pound / 16.5 kg

Dimensions
(Width x Height
x Depth)

Weight

With stand

Without stand

With stand
Without stand

45.6 x 32.0 x 13.5 inches

1156.2 x 813.1 x 342.9 mm

45.6 x 29.1 x 4.1 inches

1156.2 x 739.2 x 103.0 mm

64.4 pounds / 29.2 kg

54.3 pounds / 24.6 kg

MODELS

47LH55

(47LH55-UA)

63.4 x 37.1 x 12.5 inches

1612.0 x 944.2 x 320.0 mm

63.4 x 34.5 x 5.6 inches

1612.0 x 878.0 x 143.0 mm

160.7 pounds / 72.9 kg

130.9 pounds / 59.4 kg

55LH55

(55LH55-UA)

32CL40

(32CL40-UA)

32CL40

(32CL40-UA)

APPENDIX

115

IR CODES

Code

Function Note

(Hexa)

Code

Function Note

(Hexa)

08 POWER

Remote control Button (Power On/Off)

45 Q.MENU Remote control Button

43 MENU Remote control Button

0B INPUT Remote control Button

10-19 Number Key 0-9 Remote control Button

4C - (Dash) Remote control Button

1A FLASHBK Remote control Button

09 MUTE Remote control Button

02 VOL + Remote control Button

03 VOL - Remote control Button

00 CH Remote control Button

01 CH Remote control Button

1E FAV Remote control Button

40 Remote control Button

41 Remote control Button

07 Remote control Button

06 Remote control Button

44 ENTER Remote control Button

28 RETURN Remote control Button

7E SIMPLINK Remote control Button

30 AV MODE Remote control Button

B0 PLAY Remote control Button

BA PAUSE Remote control Button

B1 STOP Remote control Button

BD REC Remote control Button

8F REW Remote control Button

8E FF Remote control Button

D6 TV Discrete IR Code

(TV Input Selection)

C4 POWER ON Discrete IR Code

(Only Power On)

C5 POWER OFF Discrete IR Code

(Only Power Off)

5A AV1 Discrete IR Code

(AV1 Input Selection)

D0 AV2 Discrete IR Code

(AV2 Input Selection)

BF COMPONENT1 Discrete IR Code

(Component1 Input Selection)

D4 COMPONENT2 Discrete IR Code

(Component2 Input Selection)

D5 RGB-PC Discrete IR Code

(RGB-PC Input Selection)

CE HDMI1 Discrete IR Code

(HDMI1 Input Selection)

CC HDMI2 Discrete IR Code

(HDMI2 Input Selection)

E9 HDMI3 Discrete IR Code

(HDMI3 Input Selection)

DA HDMI4 Discrete IR Code

(HDMI4 Input Selection)

76 Ratio 4:3 Discrete IR Code

(Only 4:3 Mode)

77 Ratio 16:9 Discrete IR Code

(Only 16:9 Mode)

AF Ratio Zoom Discrete IR Code

(Only Zoom1 Mode)

RS-232C Setup

The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the TV’s functions externally.

■

Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.

The instructions below are provided to help with programming software or to test functionality using telenet
software.

VIDEO

AUDIO

L R

AUDIO IN

(RGB/DVI)

OPTICAL DIGITAL

AUDIO OUT

ANTENNA/

CABLE IN

RGB IN (PC)

AV IN 1

COMPONENT IN

2

3

1

MONO

( )

AUDIOVIDEO L R

/DVI IN

RS-232C IN

(

CONTROL&SERVICE)

Type of Connector; D-Sub 9-Pin Male

No. Pin Name

1 No connection
2 RXD (Receive data

)

3 TXD (Transmit data

)

4 DTR (DTE side ready

)

5 GND
6 DSR (DCE side ready

)

7 RTS (Ready to send

)

8 CTS (Clear to send

)

9 No Connection

1

6

5

9

PC

i.e)

Communication Parameters

■

Baud rate : 9600 bps (UART

)

■

Data length : 8 bits

■

Parity : None

■

Stop bit : 1 bit

■

Communication code : ASCII code

■

Use a crossed (reverse) cable.

NOTE

!

G

This product has command echo back in the
RS-232C Command.

APPENDIX

116

EXTERNAL CONTROL THROUGH RS-232C

APPENDIX

APPENDIX

117

RS-232C Configurations

Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping’.

Either cable below can be used.

Set ID

PC TV

RXD 2 3 TXD
TXD 3 2 RXD

GND 5 5 GND

DTR 4 6 DSR
DSR 6 4 DTR

RTS 7 8 CTS

CTS 8 7 RTS

D-Sub 9 D-Sub 9

PC TV

RXD 2 3 TXD
TXD 3 2 RXD

GND 5 5 GND

DTR 4 6 DTR
DSR 6 4 DSR

RTS 7 7 RTS

CTS 8 8 CTS

D-Sub 9 D-Sub 9

7-Wire Configuration

(

Serial female-female NULL modem cable

)

3-Wire Configurations

(

Not standard

)

Select

OPT I ON

.

Select

Set ID

.

Choose the desired TV ID number.
The adjustment range of Set ID is

1~99.

1

MENU

3

2

ENTER

ENTER

4

RETURN

Return to the previous menu.

MENU

Return to TV viewing.

Enter

Move

OPTION

Enter

Move

OPTION

Menu Language : English

Audio Language : English

Input Label

SIMPLINK : On

Key Lock : Off

Simple Manual

Caption : Off

Set ID : 1

Menu Language : English

Audio Language : English

Input Label

SIMPLINK : On

Key Lock : Off

Simple Manual

Caption : Off

Set ID : 1

E

E

F

1

G

Close

■

Real data mapping

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

63 : Step 99 (SET ID 99)
64 : Step 100

APPENDIX

119

01 . Power ( C o m m a n d : k a )

To control Power On/Off of the TV.

Transmission [k][a][ ][Set ID][ ][Data][Cr]

Data 00: Power Off Data 01: Power On

Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback
presents status about each function.

* Note: In this model, TV will send the Acknowledge

after power on processing completion.

There might be a time delay between command and
acknowledge.

02. Input S e l e c t (Command: x b )

To select input source for TV.

Transmission [x][b][ ][Set ID][ ][Data][Cr]

Data 00: DTV (Antenna) Data 01: DTV (Cable)

Data 10: Analog (Antenna) Data 11: Analog (Cable)

Data 20: AV/AV1 Data 21: AV2

Data 40: Component/ Component1

Data 41: Component 2

Data 60: RGB-PC Data 90: HDMI/HDMI1

Data 91: HDMI2 Data 92: HDMI3

Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

* Data21, 41, 91, 92 : Except 22LH20DC

03. Aspect R a t i o (Command: k c )

To adjust the screen format.

Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01: 4:3 06: Set by program

02: 16:9 08: Full (Only 22LH2DC)

04: Zoom 1 09: Just scan

05: Zoom 2

Reserved

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

04 . Screen M u t e (Command: k d)

To select screen mute on/off.

Transmission [k][d][ ][Set ID][ ][Data][Cr]

Data 00: Screen mute off (Picture on)

Data 01: Screen mute on (Picture off)

Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]

05. Volume M u t e (Command: k e )

To control volume mute on/off.

You can also adjust mute using the MUTE button on
remote control.

Transmission [k][e][ ][Set ID][ ][Data][Cr]

Data 00: Volume mute on (Volume off)

Data 01: Volume mute off (Volume on)

Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

06. Volume C o n t r o l (Command : k f )

To adjust volume.

You can also adjust volume with the volume buttons on
remote control.

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]

07. Contrast ( C o m m a n d : k g)

To adjust screen contrast.

You can also adjust contrast in the PICTURE menu.

Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’

Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

08. Brightness ( C o m m a n d : k h)

To adjust screen brightness.

You can also adjust brightness in the PICTURE menu.

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]

09. Color ( C o m m a n d : k i )

To adjust screen color.

You can also adjust color in the PICTURE menu.

Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]

10. Tint ( C o m m a n d : k j )

To adjust screen tint.

You can also adjust tint in the PICTURE menu.

Transmission [k][j][ ][Set ID][ ][Data][Cr]

Data Red: 00 ~Green: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]

11. Sharpness ( C o m m a n d : k k)

To adjust screen sharpness.

You can also adjust sharpness in the PICTURE menu.

Transmission [k][k][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]

APPENDIX

120

APPENDIX

12. OSD S e l e c t (Command: k l )

To select OSD (On Screen Display) on/off.

Transmission [k][l][ ][Set ID][ ][Data][Cr]

Data 00: OSD off Data 01: OSD on

Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]

13. Remote C o n t r o l L o c k Mode ( C o mmand: k m)

To lock the remote control and the front panel controls
on the set.

Transmission [k][m][ ][Set ID][ ][Data][Cr]

Data 00: Lock off Data 01: Lock on

Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]

If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.

14. Treble ( C o m m a n d : k r)

To adjust treble.

You can also adjust treble in the AUDIO menu.

Transmission [k][r][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’ as shown.

Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]

15 . Bass (Command: k s)

To adjust bass.

You can also adjust bass in the AUDIO menu.

Transmission [k][s][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’ as shown.

Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]

16. Balance ( C o m m a n d : k t)

To adjust balance.

You can also adjust balance in the AUDIO menu.

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’ as shown.

Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

17. Color T e m p e r a t u r e (C o m m a n d : k u )

To adjust color temperature.

You can also adjust color temperature in the PICTURE menu.

Transmission [k][u][ ][Set ID][ ][Data][Cr]

Data 00: Medium 01: Cool 02: Warm

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

18. Auto C o n f i g u r a t i o n ( C o m m a n d : j u )

To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.

Transmission [ j ][u][ ][Set ID][ ][Data][Cr]

Data 01: To set

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

19. Channel T u n i n g (Command : m a )

To tune channel to following physical/major/minor number.

Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel. Since
the ATSC tuner automatically maps the channel to the
Major number, the Physical number is not required when
sending a command.

Data 00: Physical Channel Number

NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87

Data 01 & 02: Major Channel Number

Data 01: High byte Data 02: Low byte

Two bytes are available for the Major and Minor, nor­mally only the second byte is used.

Data 03 & 04: Minor Channel Number

Not needed for NTSC.

APPENDIX

121

Data5:

The table above lists the binary code which must be

converted to Hexadecimal before sending. For example:

The binary code to tune the sub source to an NTSC

cable channel is “1000 0001”, which translates to “81”

in Hex.

* 7th bit : For which source do you want to change the

channel.

* 6th bit: Use a two part or one part channel. Most cases

just use 0 since it’s ignored when using NTSC.

* 5th bit: Use 0 with NTSC since it can only use the phys-

ical channel number. Normally use 1 for ATSC since most

times it doesn’t matter what the physical number is.

* 4th bit: Set to 0.

* 3-0 bits: Choose signal type.

* Tune Command Examples:

1. Tune to the analog (NTSC) cable channel 35.

Data 00 = Physical of 35 = 23

Data 01 & 02 = No Major = 00 00

Data 03 & 04 = No Minor = 00 00

Data 05 = 0000 0001 in binary = 01

Total = ma 00 23 00 00 00 00 01

2. Tune to the digital (ATSC) local channel 30-3.

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Minor is 3 = 00 03

Data 05 = 0010 0010 in binary = 22

Total = ma 00 00 00 1E 00 03 22

Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01]
[Data02][Data03][Data04][x][a][ ][Set ID]

[ ][NG][Data00][x]

20. Channel A d d / D e l (Comman d : m b )

To add and delete the channels.

Transmission [m][b][ ][Set ID][ ][Data][Cr]

Data 00: Channel Delete Data 01: Channel Add

Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

21. Key ( C o m m a n d : m c )

To send IR remote key code.

Transmission [m][c][ ][Set ID][ ][Data][Cr]

See page 115.

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

22. Backlight ( C o m m a n d : m g)

To adjust screen backlight.

Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

Step

NTSC Air

NTSC Cable

ATSC Air

ATSC Cable_std

ATSC Cable_hrc

ATSC Cable_irc

ATSC cable_auto

Reserved

...

Reserved

1

0

0

1

1

0

0

1

1

x

1

2

0

0

0

0

1

1

1

1

x

1

3

0

0

0

0

0

0

0

0

x

1

4

x

x

x

x

x

x

x

x

x

x

Reserved

5

01Use

No Use

Using Physical
Channel

6

01Tw o

One

Two/One
Part Channel

7

01Main

Sub

Main/Sub
Picture

0

0

1

0

1

0

1

0

1

x

1

APPENDIX

122

OPEN SOURCE LICENSE

-

This feature is not available for all models.

APPENDIX

Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users. This General Public License applies to most of the
Free Software Foundation's software and to any other program
whose authors commit to using it. (Some other free software
foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code
or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can
do these things.

To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get
the source code. And you must show them these terms so they
know their rights.

We protect your rights with two steps: (1) copyright the soft­ware, and (2) offer you this license which gives you legal permis­sion to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make cer­tain that everyone understands that there is no warranty for this
free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will
not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making

the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone's free use or not
licensed at all.

The precise terms and conditions for copying, distribution and
modification follow.

GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION

0. This license applies to any program or other work which con­tains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The
"Program", below, refers to any such program or work, and a
"work based on the Program" means either the Program or any
derivative work under copyright law: that is to say, a work con­taining the Program or a portion of it, either verbatim or with
modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running the Program is not restricted, and the out­put from the program is covered only if its contents constitute
a work based on the program (independent of having been
made by running the program). Whether that is true depends
on what the program does.

1. You may copy and distribute verbatim copies of the program's
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this license and to the
absence of any warranty; and give any other recipients of the
program a copy of this license along with the Program.

You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.

2. You may modify your copy or copies of the program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:

a) You must cause the modified files to carry prominent

notices stating that you changed the files and the date of
any change.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

APPENDIX

123

b) You must cause any work that you distribute or publish,

that in whole or in part contains or is derived from the
Program or any part there of, to be licensed as a whole at
no charge to all third parties under the terms of this
license.

c) If the modified program normally reads commands interac-

tively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print
or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users
may redistribute the program under these conditions, and
telling the user how to view a copy of this license.
(Exception: if the Program itself is interactive but does not
normally print such an announcement, your work based on
the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the Program, the dis­tribution of the whole must be on the terms of this license,
whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who
wrote it.

Thus, it is not the intent of this section to claim rights or con­test your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the program.

In addition, mere aggregation of another work not based on
the program with the Program (or with a work based on the
program) on a volume of a storage or distribution medium
does not bring the other work under the scope of this license.

3. You may copy and distribute the program (or a work based on
it, under section 2) in object code or executable form under
the terms of sections 1 and 2 above provided that you also
do one of the following:
a) Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange; or,

b) Accompany it with a written offer, valid for at least three

years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machine-readable copy of the corresponding
source code, to be distributed under the terms of sections
1 and 2 above on a medium customarily used for software
interchange; or,

c) Accompany it with the information you received as to the

offer to distribute corresponding source code. (This alter­native is allowed only for noncommercial distribution and
only if you received the program in object code or exe­cutable form with such an offer, in accord with Subsection
b above.)

The source code for a work means the preferred form of the
work for making modifications to it. For an executable work,
complete source code means all the source code for all mod­ules it contains, plus any associated interface definition files,
plus the scripts used to control compilation and installation
of the executable. However, as a special exception, the source
code distributed need not include anything that is normally
distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating
system on which the executable runs, unless that component
itself accompanies the executable.

If distribution of executable or object code is made by offer­ing access to copy from a designated place, then offering
equivalent access to copy the source code from the same
place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with
the object code.

4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this license. Any attempt
otherwise to copy, modify, sublicense or distribute the
Program is void, and will automatically terminate your rights
under this license. However, parties who have received copies,
or rights, from you under this license will not have their licens­es terminated so long as such parties remain in full compli­ance.

5. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works.
These actions are prohibited by law if you do not accept this
license. Therefore, by modifying or distributing the program
(or any work based on the program), you indicate your accep­tance of this license to do so, and all its terms and conditions
for copying, distributing or modifying the program or works
based on it.

6. Each time you redistribute the program (or any work based on
the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients' exercise of
the rights granted herein. You are not responsible for enforc­ing compliance by third parties to this license.

APPENDIX

124

APPENDIX

7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the con­ditions of this license, they do not excuse you from the con­ditions of this license. If you cannot distribute so as to satis­fy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the program at all. For example, if a patent
license would not permit royalty-free redistribution of the
program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and
this license would be to refrain entirely from distribution of
the program.

If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended to
apply in other circumstances.

It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest valid­ity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution sys­tem, which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.

This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.

8. If the distribution and/or use of the program is restricted in
certain countries either by patents or by copyrighted inter­faces, the original copyright holder who places the program
under this license may add an explicit geographical distribution
limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In
such case, this license incorporates the limitation as if written
in the body of this license.

9. The Free Software Foundation may publish revised and/or
new versions of the General Public License from time to time.
Such new versions will be similar in spirit to the present ver­sion, but may differ in detail to address new problems or con­cerns.

Each version is given a distinguishing version number. If the
program specifies a version number of this license which
applies to it and "any later version", you have the option of
following the terms and conditions either of that version or of

any later version published by the Free Software Foundation.
If the program does not specify a version number of this
license, you may choose any version ever published by the
Free Software Foundation.

10.If you wish to incorporate parts of the program into other free
programs whose distribution conditions are different, write to
the author to ask for permission. For software which is copy­righted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of pro­moting the sharing and reuse of software generally.

NO WARRANTY

11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD­ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.

12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PRO­GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUS­TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

APPENDIX

125

END OF TERMS AND CONDITIONS

How to apply these terms to your new programs

If you develop a new program, and you want it to be of the great­est possible use to the public, the best way to achieve this is to
make it free software which everyone can redistribute and change
under these terms.

To do so, attach the following notices to the program. It is safest
to attach them to the start of each source file to most effective­ly convey the exclusion of warranty; and each file should have at
least the "copyright" line and a pointer to where the full notice is
found.

one line to give the program's name and a brief idea of what it
does.
Copyright (C) <year> <name of author>

This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the license, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR­POSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA.

Also add information on how to contact you by electronic and
paper mail.

If the program is interactive, make it output a short notice like
this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for
details type ‘show w’. This is free software, and you are welcome
to redistribute it under certain conditions; type ‘show c’ for
details.

The hypothetical commands ‘show w’ and ‘show c’ should show
the appropriate parts of the General Public License. Of course,
the commands you use may be called something other than
‘show w’ and ‘show c’; they could even be mouse-clicks or menu
items-whatever suits your program.

You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the pro­gram, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the pro­gram ‘Gnomovision’ (which makes passes at compilers) written by
James Hacker.

signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice

This General Public License does not permit incorporating your
program into proprietary programs. If your program is a subrou­tine library, you may consider it more useful to permit linking pro­prietary applications with the library. If this is what you want to
do, use the GNU Lesser General Public License instead of this
license.

APPENDIX

126

APPENDIX

Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License, ver­sion 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public Licenses are intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users.

This license, the Lesser General Public License, applies to some
specially designated software packages - typically libraries - of
the Free Software Foundation and other authors who decide to
use it. You can use it too, but we suggest you first think careful­ly about whether this license or the ordinary General Public
License is the better strategy to use in any particular case, based
on the explanations below.

When we speak of free software, we are referring to freedom of
use, not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free soft­ware (and charge for this service if you wish); that you receive
source code or can get it if you want it; that you can change the
software and use pieces of it in new free programs; and that you
are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender
these rights. These restrictions translate to certain responsibilities
for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis
or for a fee, you must give the recipients all the rights that we
gave you. You must make sure that they, too, receive or can get
the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can
relink them with the library after making changes to the library
and recompiling it. And you must show them these terms so they
know their rights.

We protect your rights with a two-step method: (1) we copyright
the library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that
there is no warranty for the free library. Also, if the library is mod­ified by someone else and passed on, the recipients should know
that what they have is not the original version, so that the origi­nal author's reputation will not be affected by problems that
might be introduced by others.

Finally, software patents pose a constant threat to the existence
of any free program. We wish to make sure that a company can­not effectively restrict the users of a free program by obtaining a
restrictive license from a patent holder. Therefore, we insist that
any patent license obtained for a version of the library must be
consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the
ordinary GNU General Public License. This license, the GNU
Lesser General Public License, applies to certain designated
libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to per­mit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library. The
ordinary General Public License therefore permits such linking
only if the entire combination fits its criteria of freedom. The
Lesser General Public License permits more lax criteria for linking
other code with the library.

We call this license the "Lesser" General Public License because
it does Less to protect the user's freedom than the ordinary
General Public License. It also provides other free software devel­opers Less of an advantage over competing non-free programs.
These disadvantages are the reason we use the ordinary General
Public License for many libraries. However, the Lesser license pro­vides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs
must be allowed to use the library. A more frequent case is that
a free library does the same job as widely used non-free libraries.
In this case, there is little to gain by limiting the free library to free
software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body
of free software. For example, permission to use the GNU C
Library in non-free programs enables many more people to use
the whole GNU operating system, as well as its variant, the
GNU/Linux operating system.

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

APPENDIX

127

Although the Lesser General Public License is Less protective of
the users' freedom, it does ensure that the user of a program that
is linked with the Library has the freedom and the wherewithal to
run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between
a "work based on the library" and a "work that uses the library".
The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION

0. This license agreement applies to any software library or other
program which contains a notice placed by the copyright hold­er or other authorized party saying it may be distributed
under the terms of this Lesser General Public License (also
called “this license”). Each license is addressed as "you".

A “library” means a collection of software functions and/or
data prepared so as to be conveniently linked with application
programs (which use some of those functions and data) to
form executables.

The “Library”, below, refers to any such software library or work
which has been distributed under these terms. A “work based
on the Library” means either the Library or any derivative work
under copyright law: that is to say, a work containing the
library or a portion of it, either verbatim or with modifications
and/or translated straightforwardly into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.)

“Source code” for a work means the preferred form of the
work for making modifications to it. For a library, complete
source code means all the source code for all modules it con­tains, plus any associated interface definition files, plus the
scripts used to control compilation and installation of the
library.

Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running a program using the Library is not restrict­ed, and output from such a program is covered only if its con­tents constitute a work based on the library (independent of
the use of the Library in a tool for writing it). Whether that is
true depends on what the library does and what the program
that uses the library does.

1. You may copy and distribute verbatim copies of the library's
complete source code as you receive it, in any medium, pro­vided that you conspicuously and appropriately publish on

each copy an appropriate copyright notice and disclaimer of
warranty; keep intact all the notices that refer to this license
and to the absence of any warranty; and distribute a copy of
this license along with the Library.

You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.

2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent

notices stating that you changed the files and the date of
any change.

c) You must cause the whole of the work to be licensed at no

charge to all third parties under the terms of this license.

d) If a facility in the modified Library refers to a function or a

table of data to be supplied by an application program that
uses the facility, other than as an argument passed when
the facility is invoked, then you must make a good faith
effort to ensure that, in the event an application does not
supply such function or table, the facility still operates, and
performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots
has a purpose that is entirely well-defined independent of the
application. Therefore, Subsection 2d requires that any appli­cation-supplied function or table used by this function must be
optional: if the application does not supply it, the square root
function must still compute square roots.)

These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
library, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the library, the dis­tribution of the whole must be on the terms of this license,
whose permissions for other licenses extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or con­test your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the library.

In addition, mere aggregation of another work not based on
the library with the library (or with a work based on the
library) on a volume of a storage or distribution medium does
not bring the other work under the scope of this license.

APPENDIX

128

APPENDIX

3. You may opt to apply the terms of the ordinary GNU General
Public License instead of this License to a given copy of the
Library. To do this, you must alter all the notices that refer to
this License, so that they refer to the ordinary GNU General
Public License, version 2, instead of to this License. (If a newer
version than version 2 of the ordinary GNU General Public
License has appeared, then you can specify that version
instead if you wish.) Do not make any other change in these
notices.
Once this change is made in a given copy, it is irreversible for
that copy, so the ordinary GNU General Public License applies
to all subsequent copies and derivative works made from that
copy.
This option is useful when you wish to copy part of the code
of the library into a program that is not a library.

4. You may copy and distribute the library (or a portion or deriv­ative of it, under Section 2) in object code or executable form
under the terms of Sections 1 and 2 above provided that you
accompany it with the complete corresponding machine­readable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange.
If distribution of object code is made by offering access to
copy from a designated place, then offering equivalent access
to copy the source code from the same place satisfies the
requirement to distribute the source code, even though third
parties are not compelled to copy the source along with the
object code.

5. A program that contains no derivative of any portion of the
Library, but is designed to work with the Library by being
compiled or linked with it, is called a “work that uses the
Library”. Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this
license.

However, linking a “work that uses the library” with the Library
creates an executable that is a derivative of the Library
(because it contains portions of the library), rather than a
“work that uses the library”. The executable is therefore cov­ered by this license. Section 6 states terms for distribution of
such executable.

When a “work that uses the library” uses material from a head­er file that is part of the library, the object code for the work
may be a derivative work of the library even though the source
code is not.
Whether this is true is especially significant if the work can be
linked without the library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data
structure layouts and accessories, and small macros and small
inline functions (ten lines or less in length), then the use of

the object file is unrestricted, regardless of whether it is legal­ly a derivative work. (Executable containing this object code
plus portions of the library will still fall under Section 6.)

Otherwise, if the work is a derivative of the library, you may
distribute the object code for the work under the terms of
Section 6. Any executable containing that work also fall under
Section 6, whether or not they are linked directly with the
library itself.

6. As an exception to the sections above, you may also combine
or link a "work that uses the library" with the library to pro­duce a work containing portions of the library, and distribute
that work under terms of your choice, provided that the terms
permit modification of the work for the customer's own use
and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work
that the library is used in it and that the Library and its use
are covered by this license. You must supply a copy of this
license. If the work during execution displays copyright
notices, you must include the copyright notice for the library
among them, as well as a reference directing the user to the
copy of this license. Also, you must do one of these things:

a) Accompany the work with the complete corresponding

machine-readable source code for the library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete
machine-readable “work that uses the Library”, as object
code and/or source code, so that the user can modify the
library and then relink to produce a modified executable
containing the modified library. (It is understood that the
user who changes the contents of definitions files in the
library will not necessarily be able to recompile the appli­cation to use the modified definitions.)

b) Use a suitable shared library mechanism for linking with the

library. A suitable mechanism is one that (1) uses at run time
a copy of the library already present on the user’s computer
system, rather than copying library functions into the exe­cutable, and (2) will operate properly with a modified version
of the library, if the user installs one, as long as the modified
version is interface-compatible with the version that the
work was made with.

c) Accompany the work with a written offer, valid for at least

three years, to give the same user the materials specified in
Subsection 6, above, for a charge no more than the cost of
performing this distribution.

d) If distribution of the work is made by offering access to

copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these

materials or that you have already sent this user a copy.

APPENDIX

129

For an executable, the required form of the "work that uses
the library" must include any data and utility programs need­ed for reproducing the executable from it. However, as a spe­cial exception, the materials to be distributed need not
include anything that is normally distributed (in either source
or binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable
runs, unless that component itself accompanies the exe­cutable.

It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normal­ly accompany the operating system. Such a contradiction
means you cannot use both them and the library together in
an executable that you distribute.

7. You may place library facilities that are a work based on the
library side-by-side in a single library together with other
library facilities not covered by this license, and distribute
such a combined library, provided that the separate distribu­tion of the work based on the Library and of the other library
facilities is otherwise permitted, and provided that you do
these two things:

a) Accompany the combined library with a copy of the same

work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms
of the sections above.

b) Give prominent notice with the combined library of the

fact that part of it is a work based on the library, and
explaining where to find the accompanying uncombined
form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute
the library except as expressly provided under this license.
Any attempt otherwise to copy, modify, sublicense, link with,
or distribute the library is void, and will automatically termi­nate your rights under this license. However, parties who have
received copies, or rights, from you under this license will not
have their licenses terminated so long as such parties remain
in full compliance.

9. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to mod­ify or distribute the library or its derivative works. These
actions are prohibited by law if you do not accept this license.
Therefore, by modifying or distributing the library (or any work
based on the library), you indicate your acceptance of this
license to do so, and all its terms and conditions for copying,
distributing or modifying the library or works based on it.

10.Each time you redistribute the library (or any work based on
the Library), the recipient automatically receives a license
from the original licensor to copy, distribute, link with or mod­ify the library subject to these terms and conditions. You may
not impose any further restrictions on the recipients' exercise

of the rights granted herein.
You are not responsible for enforcing compliance by third
parties with this license.

11.If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the con­ditions of this license, they do not excuse you from the con­ditions of this license. If you cannot distribute so as to satis­fy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the library at all. For example, if a patent license
would not permit royalty-free redistribution of the library by
all those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this
license would be to refrain entirely from distribution of the
library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest valid­ity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution sys­tem which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a license cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.

12.If the distribution and/or use of the library is restricted in cer­tain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the library under this
license may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case,
this license incorporates the limitation as if written in the body
of this license.

13.The Free Software Foundation may publish revised and/or
new versions of the Lesser General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
library specifies a version number of this license which applies
to it and “any later version”, you have the option of following
the terms and conditions either of that version or of any later
version published by the Free Software Foundation.

APPENDIX

130

APPENDIX

If the library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.

14.If you wish to incorporate parts of the library into other free
programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software
which is copyrighted by the Free Software Foundation, write
to the Free Software Foundation; we sometimes make excep­tions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.

NO WARRANTY

15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD­ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.

16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUS­TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to apply these terms to your new libraries

If you develop a new library, and you want it to be of the great­est possible use to the public, we recommend making it free soft­ware that everyone can redistribute and change. You can do so
by permitting redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library.
It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should
have at least the “copyright” line and a pointer to where the full
notice is found.

one line to give the library's name and a brief idea of what it does.
Copyright (C) <year> <name of author>

This library is free software; you can redistribute it and/or modify
it under the terms of the GNU Lesser General Public License as
published by the Free Software Foundation; either version 2.1 of
the license, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR­POSE. See the GNU Lesser General Public License for more
details.

You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
MA 02110-1301 USA

Also add information on how to contact you by electronic and
paper mail.

You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the
library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the
library ‘Frob’ (a library for tweaking knobs) written by James
Random Hacker.

signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice

APPENDIX

131

1.Definitions.

1.0.1. “Commercial use” means distribution or otherwise making
the covered code available to a third party.

1.1. “Contributor” means each entity that creates or con­tributes to the creation of modifications.

1.2. “Contributor version” means the combination of the orig­inal code, prior modifications used by a contributor, and
the modifications made by that particular contributor.

1.3. “Covered code” means the original code or modifications
or the combination of the original code and modifications,
in each case including portions thereof.

1.4. “Electronic distribution mechanism” means a mechanism
generally accepted in the software development communi­ty for the electronic transfer of data.

1.5. “Executable” means covered code in any form other than
source code.

1.6. “Initial developer” means the individual or entity identified
as the initial Developer in the Source Code notice required
by exhibit A.

1.7. “Larger work” means a work which combines covered code
or portions thereof with code not governed by the terms
of this License.

1.8. “License” means this document.

1.8.1. “Licensable” means having the right to grant, to the maxi­mum extent possible, whether at the time of the initial
grant or subsequently acquired, any and all of the rights
conveyed herein.

1.9. “Modifications” means any addition to or deletion from
the substance or structure of either the original code or
any previous modifications. When covered code is
released as a series of files, a modification is:

A. Any addition to or deletion from the contents of a file
containing original code or previous modifications.

B. Any new file that contains any part of the original code
or previous modifications.

1.10. “Original code” means source code of computer software

code which is described in the source code notice
required by exhibit as original code, and which, at the time
of its release under this license is not already covered
code governed by this license.

1.10.1.

“Patent claims” means any patent claim(s), now owned or
hereafter acquired, including without limitation, method,
process, and apparatus claims, in any patent licensable by
grantor.

1.11. “Source code” means the preferred form of the covered
code for making modifications to it, including all modules
it contains, plus any associated interface definition files,
scripts used to control compilation and installation of an
executable, or source code differential comparisons
against either the original code or another well known,
available covered code of the contributor's choice. The
source code can be in a compressed or archival form, pro­vided the appropriate decompression or de-archiving soft­ware is widely available for no charge.

1.12. “You” (or “Your”) means an individual or a legal entity
exercising rights under, and complying with all of the terms
of, this license or a future version of this license issued
under section 6.1.
For legal entities, “You” includes any entity which controls,
is controlled by, or is under common control with You. For
purposes of this definition, “control” means (a) the power,
direct or indirect, to cause the direction or management of
such entity, whether by contract or otherwise, or (b) own­ership of more than fifty percent (50%) of the outstand­ing shares or beneficial ownership of such entity.

2. Source Code License.

2.1. The initial developer grant.
The initial developer hereby grants You a world-wide, roy­alty-free, non-exclusive license, subject to third party intel­lectual property claims:

a) under intellectual property rights (other than patent or

trademark) licensable by initial developer to use, repro­duce, modify, display, perform, sublicense and distrib­ute the original code (or portions thereof) with or with­out modifications, and/or as part of a larger work; and

(b) under patents claims infringed by the making, using or

selling of original code, to make, have made, use, prac­tice, sell, and offer for sale, and/or otherwise dispose
of the original code (or portions there of).

MOZILLA PUBLIC LICENSE

Version 1.1

---------------

APPENDIX

132

APPENDIX

(c) the licenses granted in this section 2.1(a) and (b) are

effective on the date Initial developer first distributes
original code under the terms of this license.

(d) Notwithstanding section 2.1(b) above, no patent

license is granted: 1) for code that You delete from the
original Code; 2) separate from the original code; or

3) for infringements caused by: i) the modification of
the original code or ii) the combination of the original
code with other software or devices.

2.2. Contributor Grant.
Subject to third party intellectual property claims, each
contributor hereby grants You a world-wide, royalty-free,
non-exclusive license

(a) under intellectual property rights (other than patent

or trademark) licensable by contributor, to use,
reproduce, modify, display, perform, sublicense and
distribute the modifications created by such contribu­tor (or portions thereof) either on an unmodified
basis, with other modifications, as covered code
and/or as part of a larger work; and

(b) under patent claims infringed by the making, using, or

selling of modifications made by that contributor
either alone and/or in combination with its contributor
version (or portions of such combination), to make,
use, sell, offer for sale, have made, and/or otherwise
dispose of: 1) modifications made by that contributor
(or portions thereof); and 2) the combination of mod­ifications made by that contributor with its contributor
version (or portions of such combination).

(c) the licenses granted in sections 2.2(a) and 2.2(b) are

effective on the date contributor first makes commer­cial use of the covered code.

(d) Notwithstanding section 2.2(b) above, no patent

license is granted: 1) for any code that contributor has
deleted from the contributor version; 2) separate from
the contributor version; 3) for infringements caused
by: i) third party modifications of contributor version
or ii) the combination of modifications made by that
contributor with other software (except as part of the
contributor version) or other devices; or 4) under
patent claims infringed by covered code in the
absence of modifications made by that contributor.

3. Distribution Obligations.

3.1. Application of license.
The modifications which You create or to which you con­tribute are governed by the terms of this license, including
without limitation section 2.2. The source code version of
covered code may be distributed only under the terms of
this license or a future version of this license released
under section 6.1, and you must include a copy of this
license with every copy of the source code you distribute.

You may not offer or impose any terms on any source code
version that alters or restricts the applicable version of
this license or the recipients' rights hereunder. However,
you may include an additional document offering the
additional rights described in section 3.5.

3.2. Availability of source code.
Any modification which you create or to which you con­tribute must be made available in source code form under
the terms of this license either on the same media as an
executable version or via an accepted electronic distribu­tion mechanism to anyone to whom you made an exe­cutable version available; and if made available via elec­tronic distribution mechanism, must remain available for at
least twelve (12) months after the date it initially became
available, or at least six (6) months after a subsequent
version of that particular modification has been made
available to such recipients. You are responsible for ensur­ing that the source code version remains available even if
the electronic distribution mechanism is maintained by a
third party.

3.3. Description of modifications.
You must cause all covered code to which you contribute to
contain a file documenting the changes You made to create
that covered code and the date of any change. You must
include a prominent statement that the modification is
derived, directly or indirectly, from original code provided by
the initial developer and including the name of the initial
developer in (a) the source code, and (b) in any notice in an
executable version or related documentation in which you
describe the origin or ownership of the covered code.

3.4. Intellectual property matters
(a) Third party claims.
If contributor has knowledge that a license under a third
party's intellectual property rights is required to exercise
the rights granted by such contributor under sections 2.1
or 2.2, contributor must include a text file with the source
code distribution titled "LEGAL" which describes the claim
and the party making the claim in sufficient detail that a
recipient will know whom to contact. If contributor obtains
such knowledge after the modification is made available as
described in section 3.2, contributor shall promptly modi­fy the LEGAL file in all copies contributor makes available
thereafter and shall take other steps (such as notifying
appropriate mailing lists or newsgroups) reasonably calcu­lated to inform those who received the covered code that
new knowledge has been obtained.
(b) Contributor APIs.
If contributor's modifications include an application
programming interface and contributor has knowledge of
patent licenses which are reasonably necessary to implement
that API, contributor must also include this information in
the LEGAL file.

APPENDIX

133

(c) Representations.
contributor represents that, except as disclosed pursuant
to section 3.4(a) above, contributor believes that contributor's
modifications are contributor's original creation(s)
and/or contributor has sufficient rights to grant the rights
conveyed by this license.

3.5. Required notices.
You must duplicate the notice in exhibit A in each file of
the source code. If it is not possible to put such notice in
a particular source code file due to its structure, then You
must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a
notice. If You created one or more modification(s), you
may add your name as a contributor to the notice
described in exhibit A. you must also duplicate this license
in any documentation for the source code where You
describe recipients' rights or ownership rights relating to
covered code. You may choose to offer, and to charge a
fee for, warranty, support, indemnity or liability obligations
to one or more recipients of covered code. However, you
may do so only on your own behalf, and not on behalf of
the Initial developer or any contributor. You must make it
absolutely clear than any such warranty, support, indemni­ty or liability obligation is offered by you alone, and You
hereby agree to indemnify the Initial developer and every
contributor for any liability incurred by the Initial develop­er or such contributor as a result of warranty, support,
indemnity or liability terms you offer.

3.6. Distribution of executable versions.
You may distribute covered code in executable form only if
the requirements of section 3.1-3.5 have been met for
that covered code, and if you include a notice stating that
the source code version of the covered code is available
under the terms of this license, including a description of
how and where you have fulfilled the obligations of section

3.2. The notice must be conspicuously included in any
notice in an executable version, related documentation or
collateral in which you describe recipients' rights relating
to the covered code. You may distribute the executable
version of covered code or ownership rights under a
license of your choice, which may contain terms different
from this license, provided that you are in compliance with
the terms of this license and that the license for the exe­cutable version does not attempt to limit or alter the recip­ient's rights in the source code version from the rights set
forth in this license. If you distribute the executable ver­sion under a different license you must make it absolutely
clear that any terms which differ from this license are
offered by you alone, not by the Initial developer or any
contributor. You hereby agree to indemnify the initial
developer and every contributor for any liability incurred
by the initial developer or such contributor as a result of
any such terms You offer.

3.7. Larger works.
You may create a larger work by combining covered code
with other code not governed by the terms of this license
and distribute the larger work as a single product. In such
a case, you must make sure the requirements of this
license are fulfilled for the covered code.

4. Inability to comply due to statute or regulation.
If it is impossible for you to comply with any of the terms
of this license with respect to some or all of the covered
code due to statute, judicial order, or regulation then you
must: (a) comply with the terms of this license to the max­imum extent possible; and (b) describe the limitations and
the code they affect. Such description must be included in
the LEGAL file described in section 3.4 and must be
included with all distributions of the source code. Except
to the extent prohibited by statute or regulation, such
description must be sufficiently detailed for a recipient of
ordinary skill to be able to understand it.

5. Application of this license.
This license applies to code to which the initial developer has
attached the notice in exhibit A and to related covered code.

6. Versions of the license.

6.1. New versions.
Netscape communications corporation (“Netscape”) may
publish revised and/or new versions of the license from
time to time. Each version will be given a distinguishing
version number.

6.2. Effect of new versions.
Once covered code has been published under a particular
version of the license, you may always continue to use it
under the terms of that version. You may also choose to
use such covered code under the terms of any subsequent
version of the license published by netscape. No one
other than netscape has the right to modify the terms
applicable to covered code created under this license.

6.3. Derivative works.
If You create or use a modified version of this license
(which you may only do in order to apply it to code which
is not already covered code governed by this license), You
must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",
"NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from
this license) and (b) otherwise make it clear that Your
version of the license contains terms which differ from the
Mozilla Public license and netscape Public License. (Filling
in the name of the initial developer, original code or con­tributor in the notice described in exhibit A shall not of
themselves be deemed to be modifications of this license.)

APPENDIX

134

APPENDIX

7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE
ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COV­ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT
FOR A PARTICULAR PURPOSE OR NON-INFRINGING.
THE ENTIRE RISK AS TO THE QUALITY AND PERFOR­MANCE OF THE COVERED CODE IS WITH YOU.
SHOULD ANY COVERED CODE PROVE DEFECTIVE IN
ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR
ANY OTHER CONTRIBUTOR) ASSUME THE COST OF
ANY NECESSARY SERVICING, REPAIR OR CORRECTION.
THIS DISCLAIMER OF WARRANTY CONSTITUTES AN
ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY
COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT
UNDER THIS DISCLAIMER.

8. TERMINATION.

8.1. This license and the rights granted hereunder will terminate
automatically if you fail to comply with terms herein and
fail to cure such breach within 30 days of becoming aware
of the breach. All sublicenses to the covered code which
are properly granted shall survive any termination of this
license. Provisions which, by their nature, must remain in
effect beyond the termination of this license shall survive.

8.2. If you initiate litigation by asserting a patent infringement
claim (excluding declatory judgment actions) against ini­tial developer or a contributor (the initial developer or
contributor against whom you file such action is referred
to as “Participant”) alleging that:

(a) such participant's contributor version directly or indi-

rectly infringes any patent, then any and all rights
granted by such participant to you under sections 2.1
and/or 2.2 of this license shall, upon 60 days notice
from Participant terminate prospectively, unless if within
60 days after receipt of notice you either: (i) agree in
writing to pay participant a mutually agreeable reasonable
royalty for your past and future use of modifications
made by such participant, or (ii) withdraw your litigation
claim with respect to the contributor version against
such participant. If within 60 days of notice, a reasonable
royalty and payment arrangement are not mutually
agreed upon in writing by the parties or the litigation
claim is not withdrawn, the rights granted by partici­pant to you under sections 2.1 and/or 2.2 automati­cally terminate at the expiration of the 60 day notice
period specified above.

(b) any software, hardware, or device, other than such par-

ticipant's contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by

such participant under sections 2.1(b) and 2.2(b) are
revoked effective as of the date you first made, used,
sold, distributed, or had made, modifications made by
that participant.

8.3. If you assert a patent infringement claim against partici­pant alleging that such participant's contributor version
directly or indirectly infringes any patent where such claim
is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the rea­sonable value of the licenses granted by such participant
under sections 2.1 or 2.2 shall be taken into account in
determining the amount or value of any payment or
license.

8.4. In the event of termination under sections 8.1 or 8.2
above, all end user license agreements (excluding distributors
and resellers) which have been validly granted by you or
any distributor hereunder prior to termination shall survive
termination.

9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL
THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),
CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL
DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS­TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF
ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN­TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH­OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,
WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC­TION, OR ANY AND ALL OTHER COMMERCIAL DAM­AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE
BEEN INFORMED OF THE POSSIBILITY OF SUCH DAM­AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY
TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT­ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT
APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM­AGES, SO THIS EXCLUSION AND LIMITATION MAY NOT
APPLY TO YOU.

10. U.S. GOVERNMENT END USERS.
The covered code is a "commercial item," as that term is
defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer
software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.

12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4
(June 1995), all U.S. Government end users acquire cov­ered code with only those rights set forth herein.

APPENDIX

135

11. MISCELLANEOUS.
This license represents the complete agreement concerning
subject matter hereof. If any provision of this license is
held to be unenforceable, such provision shall be reformed
only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions
(except to the extent applicable law, if any, provides oth­erwise), excluding its conflict-of-law provisions. With
respect to disputes in which at least one party is a citizen
of, or an entity chartered or registered to do business in
the united states of america, any litigation relating to this
License shall be subject to the jurisdiction of the federal
courts of the northern district of california, with venue
lying in santa clara county, california, with the losing party
responsible for costs, including without limitation, court
costs and reasonable attorneys' fees and expenses. The
application of the united nations convention on contracts
for the International sale of goods is expressly excluded.
Any law or regulation which provides that the language of
a contract shall be construed against the drafter shall not
apply to this license.

12. RESPONSIBILITY FOR CLAIMS.
As between initial developer and the contributors, each
party is responsible for claims and damages arising, directly
or indirectly, out of its utilization of rights under this
license and you agree to work with initial developer and
contributors to distribute such responsibility on an equitable
basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.

13. MULTIPLE-LICENSED CODE.
Initial developer may designate portions of the covered
code as "Multiple-Licensed". "Multiple-Licensed" means
that the initial developer permits you to utilize portions of
the covered code under your choice of the NPL or the
alternative licenses, if any, specified by the initial developer
in the file described in exhibit A.

EXHIBIT A -Mozilla Public License.

The contents of this file are subject to the Mozilla Public License
Version 1.1 (the “license”); you may not use this file except in
compliance with the License. You may obtain a copy of the
license at http://www.mozilla.org/MPL/

Software distributed under the license is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express
or implied. See the license for the specific language governing
rights and limitations under the License.

The Original Code is ______________________________________.

The Initial Developer of the Original Code
is___________________.
Portions created by ______________________ are Copyright (C)
_______________________. All Rights Reserved.

Contributor(s): ______________________________________.

Alternatively, the contents of this file may be used under the
terms of the _____ license (the "[___] License"), in which case
the provisions of [______] license are applicable instead of those
above. If you wish to allow use of your version of this file only
under the terms of the [____] license and not to allow others to
use your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the
notice and other provisions required by the [___] license. If you
do not delete the provisions above, a recipient may use your version
of this file under either the MPL or the [___] license."

NOTE: The text of this exhibit A may differ slightly from the text
of the notices in the source code files of the original code. You
should use the text of this exhibit A rather than the text found in
the original code/source code for Your modifications.

Regulatory Information cont.

FCC Compliance Statement

This equipment has been tested and found to comply
within the limits of a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.

This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation.

If this equipment does cause harmful interference to radio
or television reception (which can be determined by
turning the equipment on and off), the user is encouraged
to try to correct the interference by using one or more of
the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.

Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's (or your) authority to operate the equipment. Only
peripherals (digital input/output devices, terminals, printers,
etc.) certified to comply with the Class B limits may be
attached to this monitor. Operation with non-certified
peripherals is likely to result in interference to radio and TV
reception. Only shielded signal cables may be used with
this System.

Canadian DOC Notice

This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations. Cet appareil numérique de la classe B

respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

CE Conformity Notice

(for Europe)

Products with the “CE” Marking comply with the EMC
Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compiance with these directives implies conformity to the
following European Norms :

• EN 55022 ; Radio Frequency Interference

• EN 55024 ; Electromagnetic Immunity

• EN 61000-3-2 ; Power Line Harmonics

• EN 61000-3-3 ; Voltage Fluctuations

• EN 60950-1 ; Product Safety

Low Radiation Compliance (MPR II)

This monitor meets one of the strictest guidelines available
today for low radiation emissions, offering the user extra
shielding and an antistatic screen coating. These
guidelines, set forth by a government agency in Sweden,
limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF)
electromagnetic range.

01

NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

TCO'99 (TCO'99 applied model only)

Congratulations!

You have just purchased a TCO’99 approved and labelled
product! Your choice has provided you with a product
developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and
also to the further development of environmentally
adapted electronics products.

Regulatory Information cont.

02

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an
established method for encouraging the adaptation of
goods and services to the environment. With the growing
manufacture and usage of electronic equipment
throughout the world, there is a recognized concern for the
materials and substances used by electronic products
with regards to their eventual recycling and disposal. By
proper selection of these materials and substances, the
impact on the environment can be minimized.

There are also other characteristics of a computer, such as
energy consumption levels, that are important from the
viewpoints of both the work (internal) and natural (external)
environments. Electronic equipment in offices is often left
running continuously, resulting in unnecessary
consumption of large amounts of energy and additional
power generation. From the standpoint of carbon dioxide
emissions alone, it is vital to save energy.

What does labelling involve?

The product meets the requirements for the TCO’99
scheme which provides for international and environmental
labelling of personal computers and/or displays.
The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and
Statens Energimyndighet (The Swedish National
Energy Administration).
Approval requirements cover a wide range of issues:
ecology, ergonomics, emission of electrical and magnetical
fields, energy consumption and electrical safety.

Ecological criteria impose restrictions on the presence and
use of heavy metals, brominated and chlorinated flame
retardants, and other substances. The product must be
prepared for recycling and the manufacturing site(s) shall
be certified according to ISO14001 or EMAS registered.

Energy requirements include a demand that the system
unit and/or display, after a certain period of inactivity,
shall reduce its power consumption to a lower level in one
or more stages. The length of time to reactivate the system
unit shall be reasonable for the user.

Labelled products must meet strict environmental
demands, for example, in respect of the reduction of
electrical and magnetical fields as well as work load and

visual ergonomics.

Below you will find a brief summary of the ecological
requirements met by this product. The complete
ecological criteria document can be found at TCO
Development’s website http://www.tcodevelopment.com
or may be ordered from:

TCO Development

SE-114 94 STOCKHOLM, Sweden
Fax: [phone]
Email : [e-mail]
Information regarding TCO’99 approved and labelled
products may also be obtained at
http://www.tcodevelopment.com

Ecological requirements

Flame retardants
Flame retardants may be present in printed wiring board
laminates, cables, and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30%
by weight of the plastic in a computer casing can consist of
flame retardant substances. Many flame retardants
contain bromine or chlorine, and these flame retardants
are chemically related to PCBs (polychlorinated
biphenyls). Both the flame retardants containing bromine
or chlorine and the PCBs are suspected of giving rise to
health effects, including reproductive damage in fish­eating birds and mammals, due to the bio-accumulative*
processes when not disposed of in accordance with strict
standards for disposal.

TCO’99 requires that plastic components weighing more
than 25 grams shall not contain flame retardants with
organically bound bromine or chlorine. Flame retardants
are allowed in the printed wiring board laminates due to
the lack of commercially available alternatives.

Cadmium**
Cadmium is present in rechargeable batteries and in the
colour-generating layers of certain computer displays.
TCO’99 requires that batteries, the colour-generating
layers of display screens, and the electrical or electronics
components shall not contain any cadmium.

Mercury**
Mercury is sometimes found in batteries, relays and
switches. TCO’99 requires that batteries shall not contain
any mercury. It also demands that mercury is not present
in any of the electrical or electronics components
associated with the labelled unit. There is however one

Regulatory Information cont.

03

exception. Mercury is, for the time being, permitted in the
back light system of flat panel monitors as there today is
no commercially available alternative. TCO aims on
removing this exception when a mercury free alternative is
available.

Lead**
Lead can be found in picture tubes, display screens,
solders and capacitors. TCO’99 permits the use of lead
due to the lack of commercially available alternatives, but
in future requirements TCO Development aims at
restricting the use of lead.
_____________________________________________

* Bio-accumulative is defined as substances which

accumulate in living organisms.

**Lead, Cadmium and Mercury are heavy metals

which are bio-accumulative.

TCO’03

(TCO’03 applied model only)

Congratulations!

The display you have just purchased carries the TCO’03
Displays label.
This means that your display is designed,manufactured
and tested according to some of the strictest quality and
environmental requirements in the world. This makes for a
high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to
improve the working environment for the user and to
reduce sight and strain problems. Important
parameters are luminance, contrast, resolution,
reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneficial
both for the user and the environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the
manufacturer must have a certified environmental
management system such as EMAS or ISO 14 001

• Restrictions on

chlorinated and brominated flame retardants and
polymers

heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been
developed by TCO Development in co-operation with
scientists, experts, users as well as manufacturers all over
the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in
a more user-friendly direction. Our labelling system started
with displays in 1992 and is now requested by users and
IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

Information for Environmental Preservation

LGE. announced the 'LG Declaration for a Cleaner
Environment' in 1994, and this ideal has served as a
guiding managerial principle ever since. The Declaration is
a foundation that has allowed us to undertake
environmentally friendly activities in careful consideration
of economic, environmental, and social aspects.

We promote activities for environmental preservation, and
we specifically develop our products to embrace the
concept of environment-friendly.
We minimize the hazardous materials contained in our
products. For example, there is no cadmium to be found in
our monitors.

Information for recycling

This monitor may contain parts which could be hazardous
to the environment. It is important that this monitor be
recycled after use.

LGE. handles all waste monitors through an
environmentally acceptable recycling method. There are
several take-back and recycling systems currently in

English

Regulatory Information cont.

04

operation worldwide. Many parts will be reused and
recycled, while harmful substances and heavy metals are
treated by an environmentally friendly method.
If you want to find out more information about our
recycling program, please contact your local LG vendor or
a corporate representative of LG.

We set our vision and policies on a cleaner world by
selecting the issue of the global environment as a task for
corporate improvement. Please visit our website for more
information about our ‘green’ policies.
http://www.lge.com/about/environment/html/Recycling.jsp

Informationen zur Erhaltung der Umwelt

Im Jahr 1994 verkündete LGE die 'LG Declaration for a
Cleaner Environment' (LG Erklärung für eine sauberere
Umwelt). Seitdem dient dieses Ideal als führendes Prinzip
des Unternehmens. Diese Erklärung war die Basis für die
Durchführung von
umweltfreundlichen Aktivitäten, wobei wirtschaftliche,
umweltbezogene und soziale Aspekte in die
Überlegungen mit einbezogen wurden.
Wir fördern Aktivitäten zum Schutz der Umwelt und die
Entwicklung unserer Produkte ist darauf ausgerichtet,
unserem Konzept bezüglich Umweltfreundlichkeit gerecht
zu werden.
Wir sind darauf bedacht, den Anteil der in unseren
Produkten enthaltenen schädlichen Materialien zu
minimieren. So ist in unseren Monitoren beispielsweise
kein Kadmium zu finden.

Informationen zum Thema Recycling

Dieser Monitor enthält Teile, die umweltschädlich sein
können. Es ist unbedingt erforderlich, dass der Monitor
recycelt wird, nachdem er außer Dienst gestellt wurde.

Bei LGE. werden alle ausrangierten Monitore in einem
unter umweltbezogenen Aspekten geeigneten Verfahren
recycelt. Augenblicklich sind weltweit mehrere
Rücknahme- und Recyclingsysteme im Einsatz. Viele
Teile werden wieder verwendet und recycelt. Schädliche
Substanzen und Schwermetalle werden durch
umweltverträgliche Verfahren behandelt.
Falls Sie mehr über unser Recyclingprogramm erfahren
möchten, wenden Sie sich bitte an Ihren lokalen LG­Händler oder einen Unternehmensvertreter von LG.

Wir richten unsere Firmenpolitik auf eine sauberere
Umwelt hin aus, indem wir umweltspezifische Aspekte als
wichtigen Punkt in die Weiterentwicklung unseres
Unternehmens einfließen lassen. Zusätzliche
Informationen über unsere ‘grüne’ Firmenpolitik erhalten
Sie auf unserer Website.
http://www.lge.com/about/environment/html/Recycling.jsp

Information sur la protection del’environnement

LGE. a publié sa 'Déclaration en faveur d’un
environnement plus propre' en 1994 et celle-ci est restée,
depuis lors, un principe directeur de notre entreprise.
Cette déclaration a servi de base à notre réflexion et nous
a permis de prendre en compte à la fois les aspects
économiques et sociaux de nos activités, tout en
respectant l’environnement.

Nous encourageons les activités en faveur de la
préservation de l’environnement et c’est dans cet esprit
que nous développons nos produits : nous réduisons au
minimum les matières dangereuses qui entrent dans leur
composition et l’on ne trouve pas de cadmium, par
exemple, dans nos moniteurs.

Information sur le recyclage

Ce moniteur peut contenir des composants qui présentent
un risque pour l’environnement. Il est donc important que
celui-ci soit recyclé après usage.

LGE. traite les moniteurs en fin de cycle conformément à
une méthode de recyclage respectueuse de
l’environnement. Nous reprenons nos produits et les
recyclons dans plusieurs sites répartis dans le monde
entier. De nombreux composants sont réutilisés et
recyclés, et les matières dangereuses, ainsi que les
métaux lourds, sont traités selon un procédé écologique.
Si vous souhaitez plus de renseignements sur notre
programme de recyclage, veuillez contacter votre
revendeur LG ou un l’un de nos représentants.

Nous voulons agir pour un monde plus propre et croyons
au rôle de notre entreprise dans l’amélioration de
l’environnement. Pour plus de renseignements sur notre
politique “verte”, rendez visite à notre site :
http://www.lge.com/about/environment/html/Recycling.jsp

Deutsch

Français

05

Regulatory Information cont.

Informazioni per la tutela dell’ambiente

La LGE. ha annunciato nel 1994 la cosiddetta 'LG
Declaration for a Cleaner Environment' (Dichiarazione di
LG a favore di un ambiente più pulito), un ideale che da
allora funge da principio ispiratore della gestione
aziendale. La dichiarazione rappresenta il fondamento che
consente di intraprendere attività a favore dell'ambiente
tenendo conto degli aspetti economici, ambientali e
sociali.Noi della LG, promuoviamo attività a favore della
tutela dell'ambiente sviluppando appositamente i nostri
prodotti per cogliere il concetto del rispetto dell’ambiente
riducendo i materiali dannosi presenti nei nostri prodotti.
Ad esempio nei nostri monitor non è presente il cadmio.

Informazioni per il riciclaggio

Il monitor può presentare componenti che potrebbero
risultare eventualmente dannosi per l'ambiente. È
importante che il monitor sia riciclato al termine del suo
utilizzo.

La LGE. gestisce tutti i monitor di rifiuto con un metodo di
riciclaggio soddisfacente dal punto di vista ambientale. In
tutto il mondo sono attualmente in funzione numerosi
sistemi di riciclaggio e recupero. I diversi componenti sono
riutilizzati e riciclati, mentre le sostanze dannose e i metalli
pesanti vengono trattati con un metodo rispettoso
dell’ambiente.
Se si desiderano maggiori informazioni in merito al
programma di riciclaggio, è consigliabile rivolgersi al
proprio rivenditore LG o ad un rappresentante aziendale
della LG.

Noi della LG impostiamo la nostra visione e le nostre
politiche a favore di un mondo più pulito ponendo la
questione dell'ambiente dal punto di vista globale come
una mansione rivolta al miglioramento della nostra
azienda. Vi invitiamo a visitare il nostro sito internet per
ulteriori informazioni sulla nostra politica “verde”.
http://www.lge.com/about/environment/html/Recycling.jsp

Información para la conservación
medioambiental

LGE. presentó la 'Declaración para un entorno más limpio
de LG' en 1994 y este ideal ha servido para guiar nuestros
principios empresariales desde entonces. La Declaración
es la base que nos ha permitido llevar a cabo tareas que

respetan el medio ambiente siempre teniendo en cuenta
aspectos sociales,
económicos y medioambientales.

Promocionamos actividades orientadas a la conservación
del medio ambiente y desarrollamos nuestros productos
específicamente para que se ajusten a la filosofía que
protege el entorno.
Reducimos al máximo el uso de materiales de riesgo en
nuestros productos. Un ejemplo de ello es la ausencia
total de cadmio en nuestros monitores.

Información para el reciclaje

Este monitor puede contener piezas que entrañen riesgos
medioambientales. Es importante reciclar este monitor
después de su utilización.
LGE. trata todos los monitores usados siguiendo un
método de reciclaje que no daña al entorno. Contamos
con diversos sistemas de recuperación y reciclaje que
funcionan a nivel mundial en la actualidad. Es posible
reciclar y reutilizar muchas de las piezas, mientras que las
sustancias dañinas y los metales pesados se tratan
siguiendo un método que no perjudique al medio
ambiente. Si desea obtener más información acerca del
programa de reciclaje, póngase en contacto con su
proveedor local de LG o con un representante empresarial
de nuestra marca.

Basamos nuestra visión y nuestras políticas en un mundo
más limpio y para ellos optamos por un entorno global
como tarea principal de nuestra evolución como empresa.
Visite nuestra página Web para obtener más información
sobre nuestras políticas ecológicas.
http://www.lge.com/about/environment/html/Recycling.jsp

Informações relacionadas à preservação
ambiental

A LGE. anunciou a 'LG Declaration for a Cleaner
Environment' (Declaração da LG para um ambiente mais
limpo) em 1994 e esse ideal tem servido desde então
como um princípio administrativo de orientação. A
Declaração é a base que nos tem permitido realizar
atividades favoráveis ao ambiente com consideração
atenta aos aspectos econômicos, ambientais e sociais.

Promovemos atividades de preservação ambiental e
desenvolvemos nossos produtos para englobar

Italiano

Espanõl

Português

06

Regulatory Information cont.

especificamente o conceito de favorável ao ambiente.
Reduzimos os materiais perigosos contidos em nossos
produtos. Por exemplo, não há cádmio em nossos
monitores.

Informações relacionadas à reciclagem

Este monitor pode conter peças que podem representar
riscos ao ambiente. É importante que ele seja reciclado
após o uso.

A LGE. cuida de todos os monitores descartados através
de um método de reciclagem agradável ao ambiente. Há
vários sistemas de devolução e reciclagem atualmente
em operação no mundo. Muitas peças serão reutilizadas
e recicladas e as substâncias nocivas e os metais
pesados passarão por tratamento através de um método
favorável ao ambiente.
Para obter mais informações sobre nosso programa de
reciclagem, entre em contato com seu fornecedor LG
local ou com um representante corporativo da LG.
Definimos nossa visão e nossas políticas relacionadas a
um mundo mais limpo selecionando a questão do
ambiente global como uma tarefa de aprimoramento
corporativo. Visite nosso site para obter mais informações
sobre nossas políticas de meio ambiente.
http://www.lge.com/about/environment/html/Recycling.jsp

Informatie met betrekking tot het behoud van
het milieu

LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner
Environment' (de LG-verklaring met betrekking tot een
schoner milieu). Deze verklaring en het ideaal van een
schoner milieu fungeren sindsdien als een bestuurlijke
leidraad voor onze onderneming. Op basis van deze
verklaring ontplooien wij milieuvriendelijke activiteiten,
waarbij er zowel met sociale en economische aspecten,
als met milieuaspecten zorgvuldig rekening wordt
gehouden.

Wij ondersteunen activiteiten die zijn gericht op het
behoud van het milieu en wij houden bij het ontwikkelen
onze producten specifiek rekening met de
milieuvriendelijkheid van onze producten.
Wij minimaliseren het gebruik van schadelijke stoffen in
onze producten. Er wordt bijvoorbeeld geen cadmium
verwerkt in onze monitors.

Nederlands

Informatie met betrekking tot recycling

Deze monitor bevat materialen die schadelijk zouden
kunnen zijn voor het milieu. Het is belangrijk dat deze
monitor aan het einde van zijn levensduur wordt
gerecycled.

LGE. verwerkt alle afvalmonitors via een milieuvriendelijke
recyclingmethode. Hiervoor worden er momenteel
wereldwijd verscheidene inname- en recyclingsystemen
gehanteerd. Een groot aantal onderdelen wordt opnieuw
gebruikt en gerecycled, waarbij schadelijke stoffen en
zware metalen volgens een milieuvriendelijke methode
worden verwerkt.
Voor meer informatie over ons recyclingprogramma kunt u
contact opnemen met uw plaatselijke LG­vertegenwoordiger of een LG-vestiging.

Onze visie en ons beleid met betrekking tot een schonere
wereld vloeien voort uit het feit dat wij het milieu hebben
aangemerkt als een onderwerp dat speciale aandacht
verdient binnen onze onderneming. Bezoek onze website
voor meer informatie over ons 'groene' beleid.
http://www.lge.com/about/environment/html/Recycling.jsp

»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚

¬ 1994 „У‰Ы НУФУ‡ˆЛˇ LGE УФЫ·ОЛНУ‚‡О‡
'ƒВНО‡‡ˆЛ˛ LG ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚',
НУЪУ‡ˇ Т ЪВı ФУ ТОЫКЛЪ УТМУ‚М˚П ФЛМˆЛФУП
ЫФ‡‚ОВМЛˇ. Х‡ УТМУ‚В ˝ЪУИ ‰ВНО‡‡ˆЛЛ П˚ ТПУ„ОЛ
ФВ‰ФЛМˇЪ¸ ‰ВИТЪ‚Лˇ, У·ВТФВ˜Л‚‡˛˘ЛВ

·ВБУФ‡ТМУТЪ¸ УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ ФЛ ˝ЪУП
‰УОКМУВ ‚МЛП‡МЛВ ˝НУМУПЛ˜ВТНЛП, ˝НУОУ„Л˜ВТНЛП Л
ТУˆЛ‡О¸М˚П ‡ТФВНЪ‡П.

Г˚ ТЪЛПЫОЛЫВП ‰ВˇЪВО¸МУТЪ¸ ФУ Уı‡МВ
УНЫК‡˛˘ВИ ТВ‰˚, Ы‰ВОˇˇ УТУ·УВ ‚МЛП‡МЛВ
‡Б‡·УЪНВ М‡¯ВИ ФУ‰ЫНˆЛЛ ‚ ТУУЪ‚ВЪТЪ‚ЛЛ Т
НУМˆВФˆЛВИ ˝НУОУ„Л˜ВТНУИ ·ВБУФ‡ТМУТЪЛ.
Г˚ Т‚У‰ЛП Н ПЛМЛПЫПЫ ТУ‰ВК‡МЛВ УФ‡ТМ˚ı
‚В˘ВТЪ‚ ‚ М‡¯ВИ ФУ‰ЫНˆЛЛ. Х‡ФЛПВ, ‚ М‡¯Лı
ПУМЛЪУ‡ı ‚˚ МВ М‡И‰ВЪВ Н‡‰ПЛˇ.

»МЩУП‡ˆЛˇ ФУ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚

›ЪУЪ ПУМЛЪУ ПУКВЪ ТУ‰ВК‡Ъ¸ НУПФУМВМЪ˚,
НУЪУ˚В ПУ„ЫЪ М‡МВТЪЛ Ы˘В· УНЫК‡˛˘ВИ ТВ‰В.

Russian

07

Regulatory Information cont.

EPA

(EPA applied model only)

ENERGY STAR

is a set of power-saving guidelines
issued by the U.S. Environmental Protection
Agency(EPA).

NOM MARK (Mexico only)

ХВУ·ıУ‰ЛПУ ЫЪЛОЛБЛУ‚‡Ъ¸ ПУМЛЪУ ФУТОВ
ЛТФУО¸БУ‚‡МЛˇ.

KУФУ‡ˆЛˇ LGE ФВВ‡·‡Ъ˚‚‡ВЪ ‚ТВ ·‡НУ‚‡ММ˚В
ПУМЛЪУ˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ ФЛВПОВПУ„У
ПВЪУ‰‡ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚. œУ ‚ТВПЫ ПЛЫ
‰ВИТЪ‚Ы˛Ъ ТЛТЪВП˚ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ Л ‚УБ‚‡Ъ‡
ЛТФУО¸БУ‚‡ММУИ ФУ‰ЫНˆЛЛ. ГМУ„ЛВ НУПФУМВМЪ˚

·Ы‰ЫЪ ‚ЪУЛ˜МУ ЛТФУО¸БУ‚‡М˚ Л ЫЪЛОЛБЛУ‚‡М˚, ‚ ЪУ
‚ВПˇ Н‡Н ‚В‰М˚В ‚В˘ВТЪ‚‡ Л ЪˇКВО˚В ПВЪ‡ОО˚

·Ы‰ЫЪ У·‡·УЪ‡М˚ Т ФУПУ˘¸˛ ˝НУОУ„Л˜ВТНЛ
ФЛВПОВПУ„У ПВЪУ‰‡.

«‡ ·УОВВ ФУ‰У·МУИ ЛМЩУП‡ˆЛВИ ФУ М‡¯ВИ
ФУ„‡ППВ ЫЪЛОЛБ‡ˆЛЛ УЪıУ‰У‚ У·‡˘‡ИЪВТ¸ Н
ПВТЪМУПЫ ФУТЪ‡‚˘ЛНЫ ЛОЛ ФВ‰ТЪ‡‚ЛЪВО˛

ÍÓÔÓ‡ˆËË LG.

Г˚ УЛВМЪЛЫВПТˇ М‡ У·ВТФВ˜ВМЛВ ˝НУОУ„Л˜ВТНУИ

·ВБУФ‡ТМУТЪЛ, ТЪ‡‚ˇ ТВ·В ˆВО¸˛ „ОУ·‡О¸МЫ˛ Б‡˘ЛЪЫ
УНЫК‡˛˘ВИ ТВ‰˚. ƒУФУОМЛЪВО¸МЫ˛ ЛМЩУП‡ˆЛ˛
У М‡¯ВИ ФУОЛЪЛНВ ФУ Уı‡МВ УНЫК‡˛˘ВИ ТВ‰˚ ‚˚
ПУКВЪВ М‡ИЪЛ М‡ М‡¯ВП Т‡ИЪВ:

http://www.lge.com/about/environment/html/Recycling.jsp

As an ENERGY STAR Partner LGE U. S.
A.,Inc. has determined that this product
meets the ENERGY STAR guidelines for
energy efficiency.

08

Regulatory Information cont.

1.When this crossed-out wheeled bin symbol is attached
to a product it means the product is covered by the
European Directive 2002/96/EC.

2.All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by
the government or the local authorities.

3.The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.

4.For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased the
product.

Disposal of your old appliance

1.Quando su un prodotto è riportato il simbolo di

1.När den här symbolen med en överkryssad
soptunna på hjul sitter på en produkt innebär det
att den regleras av European Directive
2002/96/EC.

2.Alla elektriska och elektroniska produkter bör
kasseras via andra vägar än de som finns för
hushållsavfall, helst via för ändamålet avsedda
uppsamlingsanläggningar som myndigheterna
utser.

3.Om du kasserar din gamla apparat på rätt sätt
så bidrar du till att förhindra negativa
konsekvenser för miljön och människors hälsa.

4.Mer detaljerad information om kassering av din
gamla apparat kan får av kommunen,
renhållningsverket eller den butik där du köpte
produkten.

1.Als het symbool met de doorgekruiste verrijdbare
afvalbak op een product staat, betekent dit dat
het product valt onder de Europese Richtlijn
2002/96/EC.

2.Elektrische en elektronische producten mogen
niet worden meegegeven met het huishoudelijk
afval, maar moeten worden ingeleverd bij
speciale inzamelingspunten die door de lokale of
landelijke overheid zijn aangewezen.

3.De correcte verwijdering van uw oude toestel
helpt negatieve gevolgen voor het milieu en de
menselijke gezondheid voorkomen.

Smaltimento delle apparecchiature obsolete

Kassering av din gamla apparat

Uw oude toestel wegdoen

1.Ce symbole, représentant une poubelle sur
roulettes barrée d'une croix, signifie que le
produit est couvert par la directive européenne
2002/96/EC.

2.Les éléments électriques et électroniques
doivent être jetés séparément, dans les vide­ordures prévus à cet effet par votre municipalité.

3.Une élimination conforme aux instructions aidera
à réduire les conséquences négatives et risques
éventuels pour l'environnement et la santé
humaine.

4.Pour plus d'information concernant l'élimination
de votre ancien appareil, veuillez contacter votre
mairie, le service des ordures ménagères ou
encore la magasin où vous avez acheté ce
produit.

Élimination de votre ancien appareil

un bidone della spazzatura barrato da una croce
significa che il prodotto è coperto dalla direttiva
europea 2002/96/EC.

2.Tutti i prodotti elettrici ed elettronici dovrebbero
essere smaltiti separatamente rispetto alla
raccolta differenziata municipale, mediante
impianti di raccolta specifici designati dal
governo o dalle autorità locali.

3.Il corretto smaltimento delle apparecchiature
obsolete contribuisce a prevenire possibili
conseguenze negative sulla salute umana e
sull'ambiente.

4.Per informazioni più dettagliate sullo smaltimento
delle apparecchiature obsolete, contattare il
comune, il servizio di smaltimento rifiuti o il
negozio in cui è stato acquistato il prodotto.

English

French

Italian

Swedish

Dutch

WEEE (for Europe )

Regulatory Information cont.

09

1.Wenn dieses Symbol eines durchgestrichenen
Abfalleimers auf einem Produkt angebracht ist,
unterliegt dieses Produkt der europäischen
Richtlinie 2002/96/EC.

2.Alle Elektro- und Elektronik-Altgeräte müssen
getrennt vom Hausmüll über dafür staatlich
vorgesehenen Stellen entsorgt werden.

3.Mit der ordnungsgemäßen Entsorgung des alten
Geräts vermeiden Sie Umweltschäden und eine
Gefährdung der persönlichen Gesundheit.

4.Weitere Informationen zur Entsorgung des alten
Geräts erhalten Sie bei der Stadtverwaltung,
beim Entsorgungsamt oder in dem Geschäft, wo
Sie das Produkt erworben haben.

1.ŸЩ·У ¤У· ЪФ˚fiУ ‰И·ı¤ЩВИ ЩФ ‰‡М‚ФПФ ВУfi˜
‰И·БЪ·ММ¤УФ˘ О¿П·ıФ˘ ·ФЪЪИММ¿ЩˆУ, ЩfiЩВ ЩФ ЪФ˚fiУ
О·П‡ЩВЩ·И ·fi ЩЛУ E˘Ъˆ·˚О‹ O‰ЛБ›· 2002/96/EOK.

2.H ·fiЪЪИ„Л fiПˆУ ЩˆУ ЛПВОЩЪИОТУ О·И ЛПВОЩЪФУИОТУ
ЪФ˚fiУЩˆУ Ъ¤ВИ У· Б›УВЩ·И ¯ˆЪИЫЩ¿ ·fi Щ· БВУИО¿
ФИОИ·О¿ ·ФЪЪ›ММ·Щ· М¤Ыˆ О·ıФЪИЫМ¤УˆУ
ВБО·Щ·ЫЩ¿ЫВˆУ Ы˘ППФБ‹˜ ·ФЪЪИММ¿ЩˆУ, ФИ ФФ›В˜
¤¯Ф˘У ‰ЛМИФ˘ЪБЛıВ› В›ЩВ ·fi ЩЛУ О˘‚¤ЪУЛЫЛ ‹ ·fi ЩИ˜
ЩФИО¤˜ ·Ъ¯¤˜.

3.H ЫˆЫЩ‹ ·fiЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜ ı·
‚ФЛı‹ЫВИ ЫЩЛУ ·ФЩЪФ‹ Иı·УТУ ·ЪУЛЩИОТУ Ы˘УВИТУ
ˆ˜ ЪФ˜ ЩФ ВЪИ‚¿ППФУ О·И ЩЛУ ˘БВ›· ЩФ˘ ·УıЪТФ˘.

4.°И· ИФ ПВЩФМВЪВ›˜ ПЛЪФКФЪ›В˜ Ы¯ВЩИО¿ МВ ЩЛУ

·fiЪЪИ„Л ЩЛ˜ ·ПИ¿˜ Ы·˜ Ы˘ЫОВ˘‹˜, ВИОФИУˆУ‹ЫЩВ МВ
ЩФ ·ЪМfi‰›Ф ЩФИОfi БЪ·КВ›Ф, ˘ЛЪВЫ›· ‰И¿ıВЫЛ˜ ФИОИ·ОТУ

·ФЪЪИММ¿ЩˆУ ‹ ЩФ М·Б·Н› ·fi ЩФ ФФ›Ф ·БФЪ¿Ы·ЩВ ЩФ
ЪФ˚fiУ.

1.Tämä merkki tuotteessa tarkoittaa, että tuote
kuuluu sähkö- ja elektroniikkalaiteromusta
annetun EU-direktiivin 2002/96/EY
soveltamisalaan.

2.Kaikki elektroniset laitteet ovat ongelmajätettä,
joten ne on toimitettava paikalliseen
keräyspisteeseen.

3.Vanhan laitteen asianmukainen hävittäminen
ehkäisee mahdollisia ympäristöön ja
terveyteen kohdistuvia haittavaikutuksia.

4.Lisätietoa vanhan laitteen hävittämisestä saat
ottamalla yhteyden paikallisiin viranomaisiin,
kierrätyskeskukseen tai myymälään, josta ostit
laitteen.

1.Når der er et tegn med et kryds over en
skraldespand, betyder det, at produktet er
omfattet af EU-direktiv 2002/96/EC.

2.Alle elektriske og elektroniske produkter skal
smides ud et andet sted end gennem den
kommunale affaldsordning ved hjælp af specielle
indsamlingsfaciliteter, der er organiseret af staten

1.Si en un producto aparece el símbolo de un contenedor
de basura tachado, significa que éste se acoge a la
Directiva 2002/96/CE.

2.Todos los aparatos eléctricos o electrónicos se deben
desechar de forma distinta del servicio municipal de
recogida de basura, a través de puntos de recogida
designados por el gobierno o las autoridades locales.

3.La correcta recogida y tratamiento de los dispositivos
inservibles contribuye a evitar riesgos potenciales para el
medio ambiente y la salud pública.

4.Para obtener más información sobre cómo deshacerse de
sus aparatos eléctricos y electrónicos viejos, póngase en
contacto con su ayuntamiento, el servicio de recogida de
basuras o el establecimiento donde adquirió el producto.

Vanhojen laitteiden hävittäminen

Entsorgung von Altgeräten

Sådan smider du dit gamle apparat ud

∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜

Cómo deshacerse de aparatos eléctricos y
electrónicos viejos

eller de lokale myndigheder.

3.Korrekt bortskaffelse af dit gamle apparat er med
til at forhindre mulige skadevirkninger på miljøet
og menneskelig sundhed.

4.Mere detaljerede oplysninger om bortskaffelse af
dit gamle apparat kan fås ved at kontakte dit
lokale kommunekontor, renovationsselskab eller
den butik, hvor du købte produktet.

Finnish

German

Danish

Greek

Spanish

4.Wilt u meer informatie over de verwijdering van
uw oude toestel? Neem dan contact op met uw
gemeente, de afvalophaaldienst of de winkel
waar u het product hebt gekocht.

Regulatory Information cont.

10

Portuguese

Slovak

Czech

Croatian

Hungarian

Polish

Regulatory Information cont.

11

Estonian

Latvian

Lithuanian