LG 42700H - 42INCH CLASSHDTV, 32LG700H, 37LG700H, 42LG700H Technical Manual

Lifds Good

LCD TV

OWNER'S MANUAL

32LG700H
37LG700H

42LG700H

Installer Reference for Commercial Mode
MPI/PPV Card Setup see page 19

Commercial Mode Setup see pages 85-107

Please read this manual carefully before operating

your set.

Retain it for future reference.
Record model hum
See the

tl dealer

service.

of the set.

:k cover and quote

leh

Serial:

This product qualifies for ENERGYSTAR in the "factory

default" setting and this is the setting in which power savings

will be achieved.

Changing the factory default picture setting or enabling other

features will increasepower consumption that could exceed
the limits necessary to quality for EnergyStar rating.

1-800-243-0000 usA_c_s_m__us_,
1-888-865-3026 usA__:_mm_oda_us__

1-888-542-2623 C,_NADA

P/NO : SAC30708043 (0902-REV03)

WARNING / CAUTION

WARNING/ CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

WARNING/CAUTION

TO REDUCE THE RISK OF FIREAND ELECTRIC
SHOCK. DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

This reminder is provided to call the CATV system

installer's attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for

proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

Class B digital device
This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that

interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is

encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two condi-

tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any

interference received, including interference that
may cause undesired operation (of the device).

Any changes or modifications in construction of this
device which are not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

Do not attempt to modify this product in any way

without written authorization from LG Electronics.

Unauthorized modification could void the user's
authority to operate this product

SAFETYINSTRUCTIONS

IMPORTANT SAFETYINSTRUCTIONS

Read these instructions.
Keep these instructions.

Heed all warnings.
Follow all instructions.

O Do not usethis apparatus near water.

Clean only with dry cloth.

Do not block ventilation openings. Install in

any

accordance with the manufacturer's instructions.

0

Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus

(including amplifiers)that produce heat.

0

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has

two blades with one wider than the other. A
grounding type plug has two blades and a third

grounding prong, The wide blade or the third

prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

0

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from

the apparatus.

Only use attachments/accessories specified by

the manufacturer.

0

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus
combination to avoid injury from tip-over.

Unplug this apparatus during lighting storms or

when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

2

O

®
®
O

Never touch this apparatus or antenna during a
thunder or lighting storm.

When mounting a TV on the wall, make sure not to
install the TV by the hanging power and signal

cables on the back of the TV.

Do not allow an impact shock or any objects to fall
into the product, and do not drop onto the screen
with something.

CAUTION concerning the Power Cord :
It is recommend that appliances be placed upon a

dedicated circuit; that is,a single outlet circuit which
powers only that appliance and has no additional

outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet asthis could result in fire or elec-

tric shock.
Do not overload wall outlets. Overloaded wall out-

lets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire

insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its

appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement

part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in adoor, or

walked upon. Payparticular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the

TV.

O

@

O

O

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture

or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.

Do not exposeto dripping or splashinganddo not
placeobjects filled with liquids,suchasvases,cups,
etc.on or overthe apparatus(e.g.on shelvesabove

the unit).

GROUNDING
Ensure that you connect the earth ground wire to

prevent possible electric shock (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding

methods are not possible, have a qualified electri-

cian install a separate circuit breaker.

Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.

Short-circuit

Breaker

Power
Supply

DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The plug

must remain readily operable.

3

ANTENNAS

Outdoor antenna grounding
Ifan outdoor antenna is installed, follow the precau-

tions below. An outdoor antenna system should not

be located in the vicinity of overhead power linesor
other electric light or power circuits, or where it can

come in contact with such power lines or circuits as
death or serious injury can occur.

Besure the antenna system is grounded so asto pro-

vide some protection against voltage surges and

built-up static charges.
Section 810 of the National Electrical Code (NEC) in

the U.S.A.provides information with respect to prop-

er grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna dis-

chargeunit, sizeof grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes and requirements for the grounding elec-

trode.
Antenna grounding according to the

National Electrical Code, ANSI/NFPA 70

Ground Clamp

NEC: National Electrical Code

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductors
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC

Arf 250, Part H)

Cleaning
When cleaning, unplug the power cord and scrub

gently with a soft cloth to prevent scratching. Do not

spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemi-

cals such as alcohol, thinners or benzene.

O Moving

Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.

O

@

Ventilation

Install your TV where there isproper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other mate-
rials (e.g.) plastic while plugged in. Do not install in

excessivelydusty places.

Ifyou smell smoke or other odors coming from the

TV or hear strange sounds, unplug the power cord
contact an authorized service center.

Do not strongly the panel with ahand or

press upon

sharp object such as nail, pencil or pen, or make a
scratch on it

l!_ Keep product away sunlight.

the from direct

For LCD TV

If the TV feels cold to the touch, there may be
a small "flicker" when it is turned on. This is

normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the

screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on

the monitor's performance.
Avoid touching the LCD screen or holding your

finger(s) against it for long periods of time.

Doing so may produce some temporary dis-

tortion effects on the screen.

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations ofyour local authority.

4

CONTENTS

WARNING / CAUTION ............................ 1

SAFETY INSTRUCTIONS .......................... 2

FEATURES OF THIS TV ............................. 7

PREPARATION

Accessories ...................................................... 8

Front Panel Information ..................................... 9

Back Panel Information .................................... 10

Stand Instruction ............................................. 12

Cable Management ......................................... 13

Desktop Pedestal Installation ............................ 14

Swivel Stand.................................................... 14

Attaching the TV to a desk ............................... 15

VESAWall Mounting ........................................ 16

Securing the TV to the wall to prevent falling

Whenthe TV is usedon a stand .......................... 17

Antenna or Cable Connection .......................... 18

MPI Card Slot / PPV Card Installation ............... 19

HD ReceiverSetup

- Component Connection ........................... 20

- HDMI Connection ..................................... 21

- DVI to HDMI Connection .......................... 22

DVD Setup

- Component Connection ............................ 23

- HDMI Connection .................................... 24

VCR Setup

- Antenna Connection ................................. 25

- Composite (RCA) Connection ................... 25

Other A/V Source Setup ................................. 26

PC Setup

- VGA (D-Sub 15 pin) Connection ............... 27

- DVI to HDMI Connection .......................... 28

- Screen Setup for PC mode ........................ 29

Audio Out Connection .................................... 33

WATCHING TV/CHANNEL CONTROL

Remote Control Functions ............................... 34

Turning On TV ................................................ 36

Channel Selection ........................................... 36

Volume Adjustment ......................................... 36

On-Screen Menus Selection ............................. 37

Channel Setup

- Auto Scan (Auto Tuning) ........................... 38

- Add / Delete Channel (Manual Tuning) ...... 39

- Channel Editing ........................................ 40

Channel Label ................................................. 41

Input List ........................................................ 42

Example Electronic ProgramGuide ................... 43

PIP (Picture-ln-Picture) .................................... 44

Picture Size (Aspect Ratio) Control .................. 46

Preset Picture Settings

- Picture Mode - Preset ............................... 49

- Color Tone - Preset .................................. 50

Manual Picture Adjustment

- Picture Mode - User Mode ........................ 51

Picture Improvement Technology ..................... 52

Advanced Control- Black (Darkness) Level....... 53

Advanced Control - EyeCare ........................... 54

Advanced Control- Film Mode ......................... 55

Picture Reset ................................................. 56

7...................

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) ................. 57

Preset Sound Settings (Sound Mode) .............. 58

Sound Setting Adjustment - User Mode ........... 59

- SRSTruSurround XT ................................. 60

Clear Voice ..................................................... 61

Balance .......................................................... 62

TV Speakers On/Off Setup .............................. 63

Audio Reset ................................................... 64

Stereo/SAP Broadcast Setup ........................... 65

Audio Language .............................................. 66

On-Screen Menus Language Selection .............. 67

Caption Mode

- Analog Broadcasting System Captions ....... 68

- Digital Broadcasting System Captions ........ 69

- Caption Option ....................................... 70

TIME SETTING

Clock Setting

- Auto Clock Setup .................................... 71

- Manual Clock Setup ................................. 72

Auto On/Off Time Setting .............................. 73

Sleep Timer Setting ......................................... 74

Auto Shut-off Setting ....................................... 75

S

PARENTALCONTROL/RATINGS

Set Password & Lock System ........................... 76

Channel Blocking ............................................ 79

Movie & TV Rating ......................................... 80

Downloadable Rating ...................................... 83

External Input Blocking .................................... 84

Interactive TV Setup ........................................ 85

Installer Overview ............................................ 86

Interactive TV Overview ................................... 87

Commercial Mode Setup for Master TV ............ 88

Master TV Profile Setup Learning/Teaching with

USB Memory Card .......................................... 89

TLL-1100A Cloning Connections/Learning Setup

...................................................................... 1

LT2002 Cloning Connections/Learning Setup .. 92

LT2002 Cloning Learning Setup ...................... 93

Cloning Connections/Teaching Setup .............. 94

Installer Menu ................................................. 95

Reference: Detailed Instructions For Making A

Master TV ..................................................... 101

Reference: Procedures for adding Channel Label
Icons/Custom Channel Labels (2-5-4 + MENU

Mode) .......................................................... 102

Reference: Clonable Menu Features ................ 103

Reference: Power Saving Setup ....................... 104

TV Aux Input Configuration ........................... 106

TV Camport Auto Sense Operation ................ 107

z

APPENDIX

Troubleshooting ............................................ 108

Reference: LT2002 Cloning Procedure

Troubleshooting ............................................. 110

Troubleshooting FlowChart ............................ 111

Commercial Mode Check ................................ 112

Reference: RJPmodel list and input hierarchy... 112

Glossary of Terms .......................................... 113

Maintenance .................................................. 114

Product Specifications .................................... 114

Programming the Remote Control ................... 115

IR Codes ....................................................... 118

Open Source License ..................................... 120

6

FEATURES OF THIS TV

HDMP, the HDMI logo and High-Definition

Hm_ll[11111 Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing."

Manufactured under license from Dolby Laboratories.

DOLBY "Dolbz"and the double-D symbol are trademarks of

DIGITAL J Dolby Laboratories.

USBIN USB port shall be used for software update by service srs

SERVUCEONLY

personnel only. TruSurround XT

SsrS_ is a trademark of SRS Labs, Inc.

TruSurround XT technology is incorporated under

license from SRS Labs, Inc.

,I_ IMPORTANT INFORMATION TO PREVENT"IMAGE BURN

/ BURN-IN" ON YOURTV SCREEN

When a fixed image (e.g. Iogos. screen menus, video game. and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as "image burn" or "burn-in." Image burn is not covered under the manufacturer's warranty.

In order to prevent image burn. avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD. 1 or more hours for Plasma).

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

7

PREPERATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner's Manual

CD Manual

Power Cord

Remote Control,

Batteries

Protective Bracket and

Bolt for Power Cord

(Refer to R13)

x4 x4

Cable Holder

(Refer to P.13) Protection Cover Screw for stand fixing Bolts for stand assembly Torx plus

(Refer to R12) (Refer to R15) (Refer to R12) Star head screw

(Refer to R12)

Plug in type Holder

(Refer to R13)

Polishing Cloth

(Not included with all

models,)

* Wipe spots on the exterior only with the pol-

ishing cloth.

* Do not wipe roughly when removing stains.

Excessive pressure may cause scratches or
discoloration.

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin
cable) PC connection, the user

must use shielded signal interface
cables with ferrite cores to maintain

standards compliance,

8

FRONTPANELINFORMATION

_ Image shown may differ from your TV.

Stand

@

Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

Power/Standby Indicator
Illuminates red in standby mode.

Illuminates blue when the set is switched on.

Remote Control Sensor

POWER Button

_iiU¸¸¸ !_!

CH :,--

!;ii i[il

iiiii

VOL iii

E.TER®IIIii

uE.uiiii

CHANNEL(^ ,v )
Buttons

VOLUME (+,-)
Buttons

ENTER Button

MENU Button

INPUT Button

"O

_o

m

_o

0
z

9

PREPARATION

BACK PANELINFORMATION

_ Image shown may differ from your TV.

_a

r.l-I

_a

0

Z

iiiiiiiiiiiiiii; lii]}iiiiiiiiiii:itii_i_i_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!/i!_i!_i!_I

iiiii¸: _ii_i_ii!!iiiiilililii/iiiilil

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiil:_;!;!;!;!;!;!;!;!!!_ii!;;;;;;;ii_i iiFiiiiiiiiJi¸iilii]iiii!iiiiiiiiiiiiiiiiiii!!!i]iiiiiii!!i!iiiilii!iiiiiiiiiiiiiiiii!iiiii¸

/

[]

I

10

O HDMI/DVI IN

Digital Connection. Supports HD video and Digital
audio.

Accepts DVI video using an adapter or HDMI to

DVI cable (not included)

Q LAN (SERVICE ONLY)

For connecting to a control network.

@

RESET
Performs a hardware reset.
UPDATE

Enables/disables software downloads and debug
mode.

O OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and
home theater systems.

Note: In standby mode, this port doesn't work.

0 SPEAKEROUT 8£2

Connect to external speaker input.

@

RGB (PC)

Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable).

AUDIO (RGB/DVI)

1/8" headphone jack for analog PC audio input.

0 RS-232C IN (SERVICEONLY)

Used for software updates.

O

REMOTE CONTROL OUT
IR output for controlling an auxiliary device.

RJPINTERFACE (REMOTE JACK PACK PORT)
Connect to remote jack pack control output port.

COMPONENT IN
Analog Connection.

Supports HD.
Uses a red, green, and blue cable for video & a red

and white cable for audio.

AV (Audio/Video) IN 1
Analog composite connection. Supports standard

definition video only (480i).
Used for PC/DTV audio input jack.

O USB SERVICE ONLY

Used for software updates.

_ ANTENNA IN

Connect over-the air signals to this jack.

M.P.I.

Control port.
Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

_D

_D

©
z

11

?RZRARATION

m

0

z

STAND INSTRUCTION

_ Image shown may differ from your TV.

INSTALLATION

O

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

O ssemble the STAND BODY to the COVER

BASE with the included screws.

BODY

O Insert the stand as shown.

ER BASE

O

4

Tighten the stand with the
four screws(provided asparts
of the TV).

or

Tighten the two of these four screws

2 bx2 andthe tv_ Torxplusstarheadscrews

(providedasparts of the TV) to securethe TV. Tighten
the two Torx plusstar headscrewswith a star headdri-
ver bit (not provided as parts of the TV).

1

ieN EZ! :b i¸¸%¸¸¸¸¸?¸¸¸¸!¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸

}_, Make Sure the Screws nthe stand are fully i

tigh.tened. (If not tightened fully_ the product i

could tilt f6rward and fall). But do not over

tighten over-t ghtening can damage the threads
on the screws.

DETACHMENT

O

0

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

,_ii!!i!iiiiiiiiiiiiiiiii_ii!_¸¸¸_

Remove the four screws that hold the base on.

0

Detach the stand from TV.

PROTECTION COVER

After removing the stand, install the included
protection cover over the hole for the stand.

Press the PROTECTION COVER into the TV
until you hear it click.

12

CABLEMANAGEMENT

_ Image shown may differ from your TV.

O

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE

BRACKET/Screw or the Plug in type
Holder(For 32LG700H model). It will help

prevent the power cable from being removed
by accident.

PROTECTIVE BRACKET/Screw

(This feature is not available for

all models.)

Or

PLUG IN TYPE HOLDER

(For32LGT00Hmodel)

O

Install the CABLE MANAGEMENT CLIP as
shown.

If your TV hasthe CABLE HOLDER, install it
as shown and bundle the cables.

CABLE MANAGEMENT CLIP

CABLE HOLDER

O ut the cables inside the CABLE MANAGEMENT

CLIP and snap it closed.

NOTE

Do not hold the CABLE MANAGEMENT CLIP
when moving the TV.

- If the TV is dropped, you may be injured or the
product may be broken.

With some TVs. the PLUG IN TYPE HOLDER
and the CABLE HOLDER are included. If these

holders are inserted into the hole provided on
back of the TV. they cannot be removed.

_D

m

_D

©
z

13

?RERARAI°ION

_o

rT1

_o

©

z

DESKTOP PEDESTALINSTALLATION

_ Image shown may differ from your TV.

For proper ventilation, allow a clearance of 4 inches on all four sides.

4 inches

4 inches

4 inches

4 inches

_, Do not mount near or above any type of heat source.

SWIVELSTAND

The TV can be conveniently swivelled on its stand 90 ° to the left or right to provide the optimum viewing angle.

14

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing

injury or damaging the product.

-% / ./

% .._-J

'%._ ./f

4-Screws

(not provided as parts of the product)

Stand

Desk

_D

_D

O
z

_o screw: MSXL ( *L_ Tabie depth _ 8C lo mm)

ex) Table dePth: !5 ram, Screw: M5 X 25

1-Screw

(provided as parts of the product)

Stand

Desk

_ To prevent TV from fal ing over, the TV should be securely attached to the floor/wall per installation

instructions: Tipping i shakingl 0r rocking the TV may cause injury.

15

PRERARAI°ION

VESAWALL MOUNTING

-O

_a

i-rl

_a

0

z

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materi-
als, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.

J

32LG700H 200 * 100 M4 4

.....................................................................................................................................................................................................

LCDTV 37LG700H 200 * 200 M6 4

.....................................................................................................................................................................................................

42LG700H 200 * 200 M6 4

NOTE

Screw length needed depends on the wall mount standard screw specifications, the length of the
used. For further information, refer to the instruc- screws may differ depending on their specifica-
tions included with the mount, tions.

Standard dimensions for wall mount kits are shown Do not use screws that do not comply with the
in the table. VESA standard screw specifications.

When purchasing our wall mount kit. a detailed Do not tighten the screws too much. It may dam-
installation manual and all parts necessary for age the TV or allow the TV to a fall and cause per-
assembly are provided, sonal injury. LG is not liable for these kinds of acci-

Do not use screws longer then the standard dimen- dents.
sion. as they may cause damage to the inside to LG is not liable for TV damage or personal injury

the TV. when a non-VESA or non specified wall mount is
For wall mounts that do not comply with the VESA used or the consumer fails to follow the TV installa-

tion instructions.

Do not install your wall mount kit while the TV is plugged in. It may result in personal injury due to electric
shock.

WARNING

To prevent injury, this apparatus must be securelv attached to the wall in accordance with the installa-
tion instructions.

16

SECURINGTHE TV TO THE WALLTO PREVENTFALLING

WHEN THE TV IS USEDON A STAND

_ You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
_ Image shown may differ from your TV.

* This feature is not available for all models.

We recommend that you set the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don't climb on or hang from the TV.

_D

m

_D

©
z

_ Insert eye-bolts (or TV brackets and bolts) to attach the product to the wall as shown in the picture.

If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with screws (sold separately) to the wall. Match the height of the bracket that
is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

Use a sturdy rope or cord (sold separately) to tie the product. It is
safer to tie the rope so it becomes horizontal between the wall and
the product (the less slack in the rope, the better).

NOTE

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are

the same.

17

?RERARATION

_ To prevent damage do not connect to the power outlet until all connections are made between the devices.

ANTENNA OR CABLECONNECTION

l-rl

©

z

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.

For optimum picture quality, adjust the direction if needed.

, _ Multi-family Dwellings/Apartments

Wall enna socket)

Antenna ANTENNA IN
Socket

Outdo RFCoaxial Wire (75 ohm) .................................................................

Antenna
(VHF, UHF) I Single-family Dwellings/Houses !Copper Wire_

) (Connect to wall jack for outdoor antenna)

I Be careful not to bend the copper wire
I when connecting the antenna.

2. CaNe

Cable TV
Wall Jack

...........................................................................%

..........._i.

I

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV's, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.

18

MPI CARD SLOT/ PPVCARD INSTALLATION

The MPI card is equipped with an RFjack for antenna/cable signal source connection.
The MPI card slot is also available for installing a PPV (Pay-Per-View) card.

MPI Card Removal/PPV Card Installation

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

3. Detach RF cable.

4. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

5. Insert card all the way into the slot making sure it is fully seated into back plane connector.

6. Replace the two card retainer screws.

-0

_o

m

_o

©
z

RF CABLE
RF cable needs to be
disconnected to remove
the current card.

M.P.I.

Card Slot

19

EXTERNAL EQUIPMENT SETUP

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
Image shown may differ from your TV.

HD RECEIVERSETUP

m

O

z

This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,
if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as

shown below.

Component Connection

1. How to connect

0

Connect the video outputs (Y, PB, PR) of the digital set-
top box to the COMPONENT IN VIDEO jacks on
the TV. Match the jack colors (Y = green, PB = blue, and
PR = red).

O onnect the audio output of the digital set-top box to

the COMPONENT IN AUDIO jacks on theTV.

2. How to use

Turn on the digital set-top box.
(Refer to the owner's manual for the digital set-top box.)

Select Component input source using the INPUT button
on the remote control.

Supported Resolutions

Y, CB/PB, CR/PR

480i

480p

1080i

1080p

Yes

Yes
Yes
Yes

No

No 15.75 59.94

720x480i

Yes 15.75 60.00
Yes 51.47 59.94

720x480p 51.47 60.00

Yes ...................................................................................

44.96 59.94

No 1280x720p

45.00 60.00

55.72 59.94

1920x1080i 33.75 60.00

20

HDMI Connection

1. How to connect

O onnect the digital set-top box to HDMI/DVI IN 1

(DVI) or 2 jack on the TV.

O No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

Turn on the digital set-top box.

(Refer to the owner's manual for the digital set-top box.)

Select HDMI 1 or HDMI2 input source with using the INPUT
button on the remote control.

m

x

m

_D

z

m

X:)

c

m

z

m

c

HDMI-DTV

31.47 59.94

720x480p

31.47 60.00

..............:_:_19_...........................s9i_:_................

!280X720p 45.00 60.00

...................................................................................

33.72 59.94

1920xl 080i 33.75 60.00

21

EXTERNALEQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

m

x

m

z

m

X:)

c

m

z

m

c

O onnect the DVI output of the digital set-top box to

theHDMI/DVl IN 1 (DVl) jack on the TV.

O Connect the audio output of the digital set-top box to

the AUDIO (RGB/DVI) jack on the TV.

2. How to use

Turn on the digital set-top box. (Refer to the owner's man-
ual for the digital set-top box.)

Select the HDMI 1 input source on the TV using the
INPUT button on the remote control.

,_ NOTE

A DVI to HDMI cable or adapter is required for this

connection. DVl doesn't support audio, so a separate
audio connection is necessary.

22

DVDSETUP

Component Connection

1. How to connect

O

Connect the video outputs (Y, PB, PR) of the DVD to the

COMPONENT IN VIDEO jacks on the TV.
Match the jack colors (Y = green, PB = blue, and PR = red).

O Connect the audio outputs of the DVD to the

COMPONENT IN AUDIO jacks on theTV.

2. How to use

_ Turn on the DVD player, insert a DVD.
_ Select the Component input source on the TV using the

INPUT button on the remote control.

_ Refer to the DVD player's manual for operating instructions.

i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_!

m

X

_o
Z

x:)

C

Z

C

"O

Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

Video output ports

on DVD player

23

EXTERNALEQUIPMENT SETUP

HDMI Connection

1. How to connect

m

x

m

_o

z

m

X:)

c

"0

m

z

m

c

"0

O Connect the HDMI output of the DVD to the

HDMI/DVI IN 1 (DVI) or2 jack on theTV.

O No audio connection is

separate necessary.

HDMI supports both audio and video.

2. How to use

Select the HDMI1 or HDMI2 input source on the TV
using the INPUT button on the remote control.

Refer to the DVD player's manual for operating instructions.

24

VCRSETUP

_ To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

Antenna Connection

1. How to connect

O Connect the RF antenna out socket of the

VCR to the ANTENNA IN socket on the

TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

2. How to use

_ Set VCR output switch to 3 or 4 and then

tune TV to the same channel number.

_ Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner's
manual.)

Wall Jack

Antenna

r_l

x

r_l

_o

z

r_l

X:)

c

"O

r_l

z

r_l

c

"O

Composite (RCA) Connection

1. How to connect

O

Connect the AUDIO/VIDEO jacks between TV and

VCR. Match the jack colors (Video = yellow, Audio Left

= white, and Audio Right = red)

2. How to use

_ Insert a video tape into the VCR and press PLAY on the

VCR. (Refer to the VCR owner's manual.)

_ Select the AV 1 input source on the TV using the INPUT

button on the remote control.

_ If connected to AV IN 2, select AM2 input source on the TV.

D_ If you have a mono VCR, connect the audio Cable

from the VCRto the AUDIO,L/MONO jack of the

TV.

25

EXTERNALEQUIPMENT SETUP

I'1"1

><

,,-I

I"1"1

z

I"1"1

,0

c

I"1"1

z
,,-I

I"1"1

,-I

c

OTHERA/V SOURCESETUP

1. How to connect

@

Connect the AUDIO/VIDEO jacks
between TV and external equipment.
Match the jack colors.

(Video = yellow, Audio Left = white, and

Audio Right = red)

2. How to use

Select the AV2 input source on the TV using the
INPUT button on the remote control.

If connected toAV IN 1 input, select the AVl
input source on the TV.

Operate the corresponding external equipment.

Camcorder

r

Video Game Set

26

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

1. How to connect

O onnect the VGA output ofthe PC to the RGB (PC)

jack on the TV.

O Connectthe PCaudiooutput to the AUDIO (RGB/DVI)

jackon the TV.

2. How to use

Turn on the PC and the TV.
Select the RGB-PC input source on the TV using the

INPUT button on the remote control.

Supported Display Specifications
(RGB°PC, HDM[oPC)

640x3SO 31.468 70.09

720x400 31.469 70.08

640X480 31.469 59.94

800x600 3Z879 60.31
1024x768 48.363 60.00

1280x768 4Z776 59.870

1360x768 4Z712 60.015

1280X1024 63.981 60.020

NOTES

To get the best picture quality, adjust the PCgraph-

ics card to 1360x768.60Hz.

Depending on the graphics card. DOS mode may
not work if a HDMI to DVI Cable is in use.

In PC mode. there may be noise associated with the
resolution, vertical pattern, contrast or brightness.

If noise is present, change the PC output to anoth-
er resolution, change the refresh rate to another

rate or adjust the brightness and contrast on the
PICTURE menu until the picture is clear.

When you use too long RGB-PC cable, there might
be a noise on the screen.

Avoid keeping a fixed image on the screen for a

long period of time. The fixed image could become
permanently imprinted on the screen.

The synchronization input form for Horizontal and
Vertical frequencies is separate.

Depending on the graphics card. some resolution
settings may not allow the image to be positioned

on the screen properly

x

_D

z

X:)

c

z

c

27

EXTERNALEQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

m

x

m

_o

z

m

X:)

c

"O

m

z

m

c

"O

O onnect the DVI output of the PC to the HDMI/DVI IN

1 (DVI) jack on the TV.

O Connect the PC audio output to the AUDIO (RGB/DVI)

jack on the -IV.

2. How to use

Turn on the PC and the TV.

Select the HDMI1 input source on the TV using the

INPUT button on the remote control.

28

Screen Setup for PC mode

Selecting Resolution

You can choose the resolution in RGB-PC mode.
The Position, Phase, and Size can also be adjusted.

Screen _-_ Move _P ....

_eso_u_: _'_ _ 1024 x 768

m

x

m

_o

z

m

c

"0

m

z

m

c

"0

Select PICTURE.

Select Screen (RGB-PC).

Select Resolution.

Select the desired resolution.

29