LG 3G1XOUTBTS Users manual

STAREX-BSS IS2000

BSM User’s Manual

( STAREX-IS User’s Manual )

STAREX-IS BSM Manual

0

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules.

These limits are designated to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radia t e radio frequ e n c y energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

CAUTION :

Do not attempt to modify this product in any way without written authorization from

LG Electronics Inc.

Unauthorized modification could void the user's authority to operate this product.

The responsible party for this device compliance is :

Company Name : LGInfoComm U.S.A. Inc.

Address : 10225 Willow Creek RD San Diego, CA, 92131, U.S.A.

Telephone No. : 858-635-5332

SMD-011-PMA210

Page:1(877)

Issue:1.

STAREX-IS BSM Manual

0

Contents

1. Introduction to BSM................................................................................................. 36

1.1. Overview.................................................. ......................................................... 36

1.1.1. Configuration Management of System.....................................................................36

1.1.2. Fault Management of System...................................................................................36

1.1.3. Performance Management of System......................................................................38

1.1.4. Security Management of System .............................................................................39

1.1.5. Account Management of System .............................................................................39

1.2. Interoperability and Operation .......................................................................... 39

1.2.1. Configuration Management of System.....................................................................40

1.2.2. Fault Management of System...................................................................................40

1.2.3. Performance Management of System......................................................................40

1.2.4. Security Management of System .............................................................................41

1.2.5. Account Management of System .............................................................................42

1.3. BSM Configuration............................................................................................ 42

1.3.1. S/W System Boundary..............................................................................................42

1.3.2. S/W Architecture......................................................................................................43

2. BSM Environment Setting ........................................................................................ 45

2.1. OS Installation................................................................................................... 45

2.1.1. Solaris 2.7 Installation Procedures..........................................................................45

2.1.2. Network Environment Setting Procedures..............................................................63

2.2. DBMS(Informix) Installation.............................................................................. 66

2.2.1. Informix Install .........................................................................................................66

2.2.2. Environment Setting.................................................................................................75

2.2.3. Execution............................................... ...................................................................81

2.2.4. Others .......................................................................................................................82

2.3. ATM Adaptor Setup .......................................................................................... 85

2.3.1. SunATM Adopter Setup .........................................................................................85

2.3.2. SunATM S/W Installation and Solaris Setup File Modification ...............................85

2.3.3. SunATM IPoA Driver Load ......................................................................................91

2.3.4. System File Changed by atm_setup Tool ................................................................92

2.4. User Environment ........................................................................................... 129

3. BSM Package Configuration................................................................................... 129

3.1. Application Configuration................................................................................ 129

4. BSM Command....................................................................................................... 132

4.1. User Interface Command ................................................................................ 132

SMD-011-PMA210

Page:2(877)

Issue:1.

STAREX-IS BSM Manual

0

4.1.1. User Management Command .................................................................................132

4.1.2. Command Management Command .........................................................................139

4.1.3. History Management Command .............................................................................143

4.2. Loading Command........................................................................................... 148

4.2.1. Loading Control Command.....................................................................................148

4.2.2. Loading Information Display Command .................................................................154

4.3. Configuration Command.................................................................................. 163

4.3.1. Parameter Information Display Command (Display_Parameter_Information_1) ..163

4.3.2. Parameter Information Display (Display_Parameter_Information_2)....................192

4.3.3. NETWORK Information Display (Display_Parameter_Information_3) ..................213

4.3.4. Parameter Information Change Command (Change_Parameter_Information_1) ..250

4.3.5. Parameter Information Change Command (Change_Parameter_Information_2) ..288

4.3.6. Network Parameter Information Change (Change_Parameter_Info_3).................318

4.3.7. Configuration Information Display(Display_Configuration_Data)..........................329

4.3.8. Configuration Information Change (Change_Configuration_Data) ........................337

4.4. STATUS COMMAND ...................................................................................... 380

4.4.1 PROCESSOR STATUS CONTROL ..........................................................................380

4.4.2. Network Status Control .........................................................................................385

4.4.3. Can Device Status Control .....................................................................................390

4.4.4. BSC Device Status Control ....................................................................................394

4.4.5. Bts Device Status Control......................................................................................403

4.4.6. Status Message Control .........................................................................................411

4.4.7. Overload Status Control.........................................................................................414

4.5. Test Command................................................................................................ 420

4.5.1. On-Line Test-related Command ...........................................................................420

4.5.2. Test-related to Channel Element..........................................................................424

4.5.3. Vocoder Test Function ..........................................................................................426

4.5.4. Link Test Function ...................................... ...........................................................434

4.5.5. Command related to BSC Virtual Call Test...........................................................441

4.5.6. TRAFFIC PATH TESTING FUNCTION.................................................................447

4.5.7. Call Trace Testing Function ..................................................................................450

4.5.8. Number of Data Call User Display Function (Active/Dormant) ............................456

4.5.9. DATA Call User Status Display Function by IMSI ................................................457

4.5.10. IOS Message Display Function ............................................................................458

4.5.11. POWER MONITORING Function ..........................................................................461

4.6. No.7 Command................................................................................................ 463

4.6.1. Related Command...................................................................................................463

SMD-011-PMA210

Page:3(877)

Issue:1.

STAREX-IS BSM Manual

0

4.6.2. Signaling Link Operation Management Function ...................................................465

4.6.3. Maintenance Function Command ...........................................................................486

4.7. Statistics Command......................................................................................... 491

4.7.1. Traffic related Statistics Command .......................................................................493

4.7.2. Handoff Related Statistics Function ......................................................................497

4.7.3. Call Related Statistics Function .............................................................................503

4.7.4. Packet Related........................................................................................................515

4.7.5. Other Statistics Related Commands ......................................................................518

4.8. Alarm/Fault Command..................................................................................... 521

4.8.1. Alarm/Fault Display................................................................................................523

4.8.2. Alarm/Fault Inhibition.............................................................................................529

4.8.3. Alarm/Fault Control................................................................................................533

4.8.4. Environment Alarm Control ...................................................................................536

4.9. Operation through GUI.................................................................................... 546

4.9.1. Manager Window....................................................................................................546

4.9.2. Interm Window .......................................................................................................546

4.9.3. Batch Job ................................................................................................................550

4.9.4. Console Window .....................................................................................................558

4.9.5. Controller ...............................................................................................................559

4.9.6. Status Window (stmGUI) ........................................................................................561

4.9.7. Neighbor Control Window (neighbor)....................................................................576

4.9.8. Call Trace Window.................................................................................................583

4.9.9. BTS Address Search Window. ...............................................................................594

5. BSM On-Line Message .......................................................................................... 601

5.1. Fault/Alarm Message ...................................................................................... 601

5.1.1. Alarm Message........................................... ............................................................601

5.1.2. Fault Message ........................................................................................................68 9

5.2. Status Command ............................................................................................. 717

5.2.1. Processor Status Change Report ...........................................................................717

5.2.2. Overload Status Change Report Function .............................................................724

5.3. Loading Message ............................................................................................ 726

5.3.1. Processor Initialization Start Message ..................................................................726

5.3.2. Processor Initialization End Message....................................................................726

5.3.3. Loading Start Message...........................................................................................727

5.3.4. Loading Completion Message ................................................................................728

5.3.5. Loading Failure Message .......................................................................................729

5.3.6. Firmware Update Report Message ........................................................................729

SMD-011-PMA210

Page:4(877)

Issue:1.

STAREX-IS BSM Manual

0

6. Trouble Shoot ........................................................................................................ 730

6.1. If BSM is not operated.................................................................................... 730

6.1.1. If BSM is not initialized ..........................................................................................730

6.1.2. It can not function normally despite of its initialization ........................................732

6.2. If Graphic Application is not run ..................................................................... 732

6.2.1. Environment Variables...........................................................................................733

6.2.2. If Manager in Remote Area is not operated ..........................................................734

7. CHG- Appendix ..................................................................................................... 736

7.1. Alarm/Fault Message Description and List..................................................... 736

7.1.1. Alarm Message Description and List.....................................................................736

7.1.2. Fault Message Description and List ......................................................................743

7.1.3. Measures for Alarm Message ................................................................................744

7.1.4. Measures for Fault Message..................................................................................762

7.2. Status Message Description and LIST Status Definition and LIST................. 766

7.3. DCI Debugger Command................................................................................. 769

7.3.1. Tx/Rx Message Trace Function ............................................................................769

7.3.2. Function to test Function .......................................................................................773

7.3.3. Status Display Funciton .........................................................................................775

7.3.4. Other Supplementary Function ..............................................................................779

7.4. Statistic Message............................................................................................ 781

7.4.1. Traffic Related .......................................................................................................781

7.4.2. Handoff Statistic Function......................................................................................784

7.4.3. Call Related Statistic Function...............................................................................785

7.4.4. Packet .....................................................................................................................790

7.5. PLD Data Structure......................................................................................... 793

7.5.1. BSM layer ...............................................................................................................793

7.5.2. CNP ONLY..............................................................................................................793

7.5.3. PNP ONLY ..............................................................................................................798

7.5.4. PCP ONLY ..............................................................................................................804

7.5.5. CCP ONLY ..............................................................................................................807

7.5.6. NCP ONLY..............................................................................................................824

7.5.7. SCP ONLY ..............................................................................................................839

7.5.8. CCP/BSP COMMON................................................................................................842

7.5.9. BSP Layer...............................................................................................................857

7.6. Abbreviations.................................................................................................. 877

SMD-011-PMA210

Page:5(877)

Issue:1.

STAREX-IS BSM Manual

0

Figures

FIG. 1.3-1 BSM S/W CONFIGURATION ......................................................................... 44

FIG. 2.1-1 OS LANGUAGE SELECTION SCREEN.......................................................... 45

FIG. 2.1-2 OS INSTALLATION LANGUAGE AND SELECTION SCREEN 2................... 46

FIG. 2.1-3 OS INSTALLATION TIME SETTING ............................................................ 46

FIG. 2.1-4 HOST NAME INPUT SCREEN .................................................................... 47

FIG. 2.1-5 HOST NAME INPUT 2 .................................................................................. 47

FIG. 2.1-6 NETWORK SETTING SCREEN ..................................................................... 48

FIG. 2.1-7 IP ADDRESS INPUT SCREEN....................................................................... 48

FIG. 2.1-8 IP ADDRESS INPUT SCREEN 2.................................................................... 49

FIG. 2.1-9 NETWORK BASIC SETTING SUMMARY SCREEN....................................... 49

FIG. 2.1-10 DNS SETTING SCREEN.............................................................................. 50

FIG. 2.1-11 DNS SETTING SCREEN 2........................................................................... 50

FIG. 2.1-12 DNS SETTING SUMMARY SCREEN........................................................... 51

FIG. 2.1-13 SUBNET SETTING SCREEN .................................................................... 51

FIG. 2.1-14 SUBNET SETTING SCREEN 2 ................................................................... 51

FIG. 2.1-15 SUBNET SETTING SCREEN 3 ................................................................... 52

FIG. 2.1-16 OS TIME SETTING METHOD SCREEN ...................................................... 52

FIG. 2.1-17 OS TIME SETTING REGION SELECTION SCREEN ................................... 53

FIG. 2.1-18 OS TIME SETTING REGION SELECTION SCREEN 2 ................................ 53

FIG. 2.1-19 TIME SETTING SCREEN ............................................................................ 54

FIG. 2.1-20 SUBNET AND TIME SETTING SUMMARY SCREEN ................................. 54

FIG. 2.1-21 OS INSTALLATION METHOD SELECTION SCREEN................................. 54

FIG. 2.1-22 ATTENTION TO THE INSTALLATION OF OS .......................................... 55

FIG. 2.1-23 X-TERMINAL SETTING SCREEN .............................................................. 55

FIG. 2.1-24 USER LANGUAGE SELECTION SCREEN ................................................... 56

FIG. 2.1-25 OS INSTALLATION CATEGORY SELECTION SCREEN............................. 56

FIG. 2.1-26 OS INSTALLATION CATEGORY SELECTION SCREEN 2.......................... 57

FIG. 2.1-27 OS INSTALLATION DISK SELECTION SCREEN........................................ 57

FIG. 2.1-28 WARNING SENTENCE SCREEN RESULTING FROM THE DISK SETTING58

FIG. 2.1-29 SELECTION SCREEN FOR DISK INSTALLATION METHOD ..................... 58

FIG. 2.1-30 SELECT SCREEN FOR DISK INSTALLATION METHOD ........................... 58

FIG. 2.1-31 SELECTED DISK INFORMATION DISPLAY SCREEN................................. 59

FIG. 2.1-32 AREA INFORMATION DISPLAY SCREEN FOR THE DISK DIVISION......... 60

FIG. 2.1-33 DISK ALLOCATION RESULT DISPLAY SCREEN....................................... 61

SMD-011-PMA210

Page:6(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 2.1-34 REMOTE FILE SERVER INSTALLATION SCREEN .................................... 62

FIG. 2.1-35 SET UP INFORMATION DISPLAY SCREEN FOR THE INSTALLATION.... 62

FIG. 4.1-1 BSM SYSTEM LOGIN WINDOW.................................................................. 132

FIG. 4.1-2 LOG-OUT.................................................................................................... 133

FIG. 4.1-3 USER ID REGISTER .................................................................................... 134

FIG. 4.1-4 ERRORS WHEN REGISTERING USER ID.................................................. 134

FIG. 4.1-5 USER ID DELETION ................................................................................. 135

FIG. 4.1-6 ERRORS WHEN DELETING USER ID THAT DOES NOT EXIST................ 135

FIG. 4.1-7 ERRORS WHEN DELETING THE MANAGER CLASS ID............................. 136

FIG. 4.1-8 USER CLASS CHANGE............................................................................... 137

FIG. 4.1-9 ERRORS WHEN CHANGING THE USE CLASS OF THE MANAGER .......... 137

FIG. 4.1-10 USER INFORMATION DISPLAY................................................................ 138

FIG. 4.1-11 USER PASSWORD CHANGE ..................................................................... 139

FIG. 4.1-12 COMMAND CLASS MODIFICATION....................................................... 140

FIG. 4.1-13 COMMAND CLASS DISPLAY.................................................................. 141

FIG. 4.1-14 COMMAND INFORMATION DISPLAY BY NAME ..................................... 142

FIG. 4.1-15 COMMAND INFORMATION DISPLAY BY CRN ........................................ 143

FIG. 4.1-16 COMMAND HISTORY DISPLAY................................................................ 144

FIG. 4.1-17 MESSAGE HISTORY DISPLAY START..................................................... 146

FIG. 4.1-18 MESSAGE HISTORY DISPLAY END....................................................... 147

FIG. 4.2-1 BLOCKING LOADING PERFORMANCE RESULT ....................................... 149

FIG. 4.2-2 ACTIVATION LOADING PERFORMANCE RESULT ................................... 150

FIG. 4.2-3 FLASH MEMORY UPDATE RESULT.......................................................... 151

FIG. 4.2-4 LOADING INFORMATION DISPLAY COMMAND EXECUTION RESULT . 155

FIG. 4.2-5 LOADING HISTORY DISPLAY FUNCTION EXECUTION RESULT ............. 157

FIG. 4.2-6 BLOCK LOADING HISTORY DISPLAY RESULT......................................... 159

FIG. 4.2-7 LOADING STATE DISPLAY COMMAND EXECUTION RESULT (WHEN

THERE IS A PROCESSOR THAT IS PERFORMING LOADING) ............................. 160

FIG. 4.2-8 LOADING STATE DISPLAY COMMAND EXECUTION RESULT (WHEN

THERE IS NO PROCESSOR THAT IS PERFORMING LOADING)........................... 160

FIG. 4.2-9 VERSION INFORMATION DISPLAY COMMAND EXECUTION RESULT .... 162

FIG. 4.3-1 BTS PARAMETER DISPLAY....................................................................... 165

FIG. 4.3-2 SECTOR PARAMETER INFORMATION DISPLAY.................................... 166

FIG. 4.3-3 CDMA CHANNEL PARAMETER INFORMATION DISPLAY........................ 167

FIG. 4.3-4 SYSTEM PARAMETER MESSAGE DISPLAY.............................................. 169

FIG. 4.3-5 EXTENDED SYSTEM PARAMETER MESSAGE DISPLAY.......................... 171

FIG. 4.3-6 NEIGHBOR LIST PARAMETER INFORMATION DISPLAY ......................... 173

SMD-011-PMA210

Page:7(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.3-7 BTS QOS(QUALITY OF SERVICE) DISPLAY.............................................. 174

FIG. 4.3-8 DISPLAY OF PARAMETER THAT CONTROLS CHIP POWER ................. 175

FIG. 4.3-9 OCNS STATE DISPLAY .............................................................................. 176

FIG. 4.3-10 CURRENT POWER CONTROL DISPLAY................................................... 177

FIG. 4.3-11 TIC(TRANSCEIVER INTERFACE CARD) DATA DISPLAY ....................... 178

FIG. 4.3-12 OCNS DISPLAY......................................................................................... 179

FIG. 4.3-13 POWER MANAGEMENT PARAMETER INFORMATION DISPLAY ........... 180

FIG. 4.3-14 ACCESS CHANNEL PARAMETER INFORMATION DISPLAY................... 181

FIG. 4.3-15 TXMS DISPLAY......................................................................................... 182

FIG. 4.3-16 GSRM PARAMETER INFORMATION DISPLAY ........................................ 184

FIG. 4.3-17 ACCESS PARAMETER MESSAGE DISPLAY............................................. 186

FIG. 4.3-18 PAGING CHANNEL PARAMETER INFORMATION DISPLAY................... 187

FIG. 4.3-19 PILOT CHANNEL PARAMETER INFORMATION DISPLAY...................... 188

FIG. 4.3-20 SYNC. CHANNEL PARAMETER INFORMATION DISPLAY...................... 189

FIG. 4.3-21 QUICK PAGING CHANNEL PARAMETER INFORMATION DISPLAY....... 190

FIG. 4.3-22 HOPPING PILOT BEACON CHANNEL PARAMETER INFORMATION

DISPLAY................................................................................................................. 191

FIG. 4.3-23 BSC INFORMATION VERIFICATION........................................................ 192

FIG. 4.3-24 IOS PARAMETER VERIFICATION ............................................................ 193

FIG. 4.3-25 FORWARD LINK POWER MANAGEMENT INFORMATION (RS1)

VERIFICATION....................................................................................................... 195

FIG. 4.3-26 BACKWARD LINK POWER MANAGEMENT INFORMATION (RS1)

VERIFICATION....................................................................................................... 197

FIG. 4.3-27 FORWARD LINK POWER MANAGEMENT INFORMATION (RS2)

VERIFICATION....................................................................................................... 199

FIG. 4.3-28 BACKWARD LINK POWER MANAGEMENT INFORMATION (RS2)

VERIFICATION....................................................................................................... 201

FIG. 4.3-29 SERVICE OPTION FER VERIFICATION.................................................... 203

FIG. 4.3-30 MAHHO VERIFICATION ........................................................................... 204

FIG. 4.3-31 LOCATION VERIFICATION ...................................................................... 205

FIG. 4.3-32 SCH VERIFICATION ................................................................................. 206

FIG. 4.3-33 POWER CONTROL DATA VERIFICATION ............................................... 208

FIG. 4.3-34 BTS NAME DISPLAY ................................................................................ 209

FIG. 4.3-35 PCP TIMER INFORMATION VERIFICATION............................................ 210

FIG. 4.3-36 PCF PARAMETER INFORMATION VERIFICATION ................................. 211

FIG. 4.3-37 PCF MAC ADDRESS INFORMATION VERIFICATION .............................. 212

FIG. 4.3-38 CAN ATM NODE INFORMATION DISPLAY.............................................. 214

SMD-011-PMA210

Page:8(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.3-39 CAN PVC SETTING INFORMATION DISPLAY......................................... 215

FIG. 4.3-40 CAN NETWORK PARAMETER INFORMATION DISPLAY........................ 216

FIG. 4.3-41 CAN INTER BSC AAL2 SETTING INFORMATION DISPLAY ................... 217

FIG. 4.3-42 CAN INTER BSC AAL5 SETTING INFORMATION DISPLAY ................... 218

FIG. 4.3-43 CAN ATM NODE INFORMATION DISPLAY.............................................. 219

FIG. 4.3-44 PCF ATM NODE INFORMATION DISPLAY .............................................. 220

FIG. 4.3-45 CAN PVC SETTING INFORMATION DISPLAY......................................... 221

FIG. 4.3-46 CAN PCF PVC SETTING INFORMATION DISPLAY................................. 222

FIG. 4.3-47 CPN METWORK PARAMETER INFORMATION DISPLAY........................ 223

FIG. 4.3-48 CPN DATA AAL2/5 CONNECTION INFORMATION DISPLAY................. 224

FIG. 4.3-49 CPN PCF AAK2/5 CONNECTION INFORMATION DISPLAY.................... 225

FIG. 4.3-50 BSC ATM NODE INFORMATION DISPLAY .............................................. 226

FIG. 4.3-51 SLB ATM NODE INFORMATION DISPLAY .............................................. 227

FIG. 4.3-52 VCB ATM NODE INFORMATION DISPLAY ......................................... 228

FIG. 4.3-53 ALB ATM NODE INFORMATION DISPLAY.............................................. 229

FIG. 4.3-54 BTS ATM NODE INFORMATION DISPLAY.............................................. 230

FIG. 4.3-55 BSC-BTS TRUNK INFORMATION DISPLAY ........................................... 231

FIG. 4.3-56 BSC PVC SETTING INFORMATION DISPLAY ......................................... 233

FIG. 4.3-57 BSC SLB PVC SETTING INFORMATION DISPLAY.................................. 234

FIG. 4.3-58 BSC VCB PVC SETTING INFORMATION DISPLAY................................. 235

FIG. 4.3-59 BSC ALB PVC SETTING INFORMATION DISPLAY ................................. 236

FIG. 4.3-60 BTS LOCAL PVC SETTING INFORMATION DISPLAY ............................ 237

FIG. 4.3-61 BTS OUTER PVC SETTING INFORMATION DISPLAY............................ 238

FIG. 4.3-62 BSC NETWORK PARAMETER INFORMATION DISPLAY......................... 239

FIG. 4.3-63 BSC ALP NETWORK PARAMETER INFORMATION DISPLAY................. 240

FIG. 4.3-64 BSC INTER BSC AAL2 INFORMATION DISPLAY .................................... 241

FIG. 4.3-65 BSC INTER BTS AAL2 INFORMATION DISPLAY.................................... 242

FIG. 4.3-66 BSC INTER CAN AAL2/5 INFORMATION DISPLAY ................................ 243

FIG. 4.3-67 BSC INTER SLB AAL5 INFORMATION DISPLAY .................................... 244

FIG. 4.3-68 BSC INTER VCB AAL5 INFORMATION DISPLAY.................................... 245

FIG. 4.3-69 BSC INTER ALB AAL5 INFORMATION DISPLAY.................................... 246

FIG. 4.3-70 BTS NETWORK PARAMETER INFORMATION DISPLAY ........................ 247

FIG. 4.3-71 BTS INTER BTS AAL2 INFORMATION DISPLAY.................................... 248

FIG. 4.3-72 BTS INTER RCU AAL5 INFORMATION DISPLAY.................................... 249

FIG. 4.3-73 BTS PARAMETER INFORMATION DISPLAY......................................... 253

FIG. 4.3-74 SECTOR PARAMETER INFORMATION CHANGE .................................... 253

FIG. 4.3-75 CDMA CHANNEL PARAMETER INFORMATION DISPLAY...................... 254

SMD-011-PMA210

Page:9(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.3-76 SYSTEM PARAMETER CHANGE(1) DISPLAY ......................................... 256

FIG. 4.3-77 SYSTEM PARAMETER CHANGE(2) DISPLAY ......................................... 257

FIG. 4.3-78 EXTENDED SYSTEM PARAMETER CHANGE(1) DISPLAY ..................... 259

FIG. 4.3-79 EXTENDED SYSTEM PARAMETER CHANGE(2) DISPLAY ..................... 261

FIG. 4.3-80 NEIGHBOR CELL ADDITION DISPLAY .................................................... 263

FIG. 4.3-81 NEIGHBOR CELL INFORMATION DELETION DISPLAY .......................... 263

FIG. 4.3-82 HOPPING BEACON PARAMETER CHANGE DISPLAY............................. 265

FIG. 4.3-83 QOS PARAMETER INFORMATION CHANGE DISPLAY ........................... 266

FIG. 4.3-84 CHIP POWER CONTROL INFORMATION CHANGE DISPLAY.................. 268

FIG. 4.3-85 TIC PARAMETER INFORMATION CHANGE DISPLAY ............................ 269

FIG. 4.3-86 OCNS PARAMETER CHANGE DISPLAY................................................... 270

FIG. 4.3-87 POWER CONTROL PARAMETER INFORMATION DISPLAY .................... 272

FIG. 4.3-88 ACCESS CHANNEL PARAMETER INFORMATION CHANGE DISPLAY. 273

FIG. 4.3-89 TXMS PARAMETER INFORMATION CHANGE DISPLAY......................... 274

FIG. 4.3-90 BTS CALIBRATION START DISPLAY...................................................... 275

FIG. 4.3-91 BTS CALIBRATION TIME CHANGE DISPLAY......................................... 276

FIG. 4.3-92 PC GLOBAL REDIRECT PARAMETER INFORMATION CHANGE DISPLAY

.............................................................................................................................. . 278

FIG. 4.3-93 ACCESS PARAMETER INFORMATION CHANGE DISPLAY..................... 280

FIG. 4.3-94 PAGING CHANNEL PARAMETER INFORMATION DISPLAY................... 281

FIG. 4.3-95 PILOT CHANNEL PARAMETER INFORMATION CHANGE DISPLAY ...... 282

FIG. 4.3-96 SYNC CHANNEL PARAMETER INFORMATION CHANGE DISPLAY ....... 283

FIG. 4.3-97 QUICK PAGING CHANNEL PARAMETER INFORMATION CHANGE

DISPLAY................................................................................................................. 284

FIG. 4.3-98 HOPPING PILOT BEACON CHANNEL PARAMETER INFORMATION

CHANGE DISPLAY................................................................................................. 285

FIG. 4.3-99 CDMA CHANNEL FA TEST START DISPLAY ......................................... 286

FIG. 4.3-100 CDMA CHANNEL FA TEST TERMINATION DISPLAY .......................... 287

FIG. 4.3-101 DORMANT TIMER CHANGE DISPLAY................................................... 290

FIG. 4.3-102 PACKET ZONE DATA CHANGE DISPLAY............................................. 290

FIG. 4.3-103 FACILITIES MANAGEMENT TIMER

CHANGE DISPLAY....................... 291

FIG 4.3-104 HANDOFF TIMER CHANGE DISPLAY................................................... 292

FIG. 4.3-105 BSC SUPPLEMENT SERVICES TIMER CHANGE DISPLAY................... 293

FIG. 4.3-106 BSC CALL PROCESSING TIMER CHANGE DISPLAY............................. 294

FIG. 4.3-107 BSC MOBILITY MANAGEMENT TIMER CHANGE DISPLAY ................. 295

FIG. 4.3-108 A8 A9 INTERFACE TIMER CHANGE ..................................................... 296

FIG. 4.3-109 A3, A7 INTERFACE TIMER CHANGE .................................................... 297

SMD-011-PMA210

Page:10(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.3-110 FORWARD LINK POWER MANAGEMENT INFORMATION (RS1) CHANGE

.............................................................................................................................. . 299

FIG. 4.3-111 BACKWARD LINK POWER MANAGEMENT INFORMATION (RS1)

CHANGE................................................................................................................. 299

FIG. 4.3-112 FORWARD LINK POWER MANAGEMENT INFORMATION (RS2) CHANGE

.............................................................................................................................. . 301

FIG. 4.3-113 BACKWARD LINK POWER MANAGEMENT INFORMATION (RS2)

CHANGE................................................................................................................. 302

FIG. 4.3-114 SERVICE OPTION FER CHANGE............................................................ 304

FIG. 4.3-115 MAHHO DATA CHANGE......................................................................... 306

FIG. 4.3-116 LOCATION PARA INFORMATION CHANGE .......................................... 307

FIG. 4.3-117 SCH PARAMETER INFORMATION CHANGE ......................................... 308

FIG. 4.3-118 POWER CONTROL PARAMETER INFORMATION (1) CHANGE ............ 310

FIG. 4.3-119 POWER CONTROL PARAMETER INFORMATION (2) CHANGE ............ 311

FIG. 4.3-120 POWER CONTROL PARAMETER INFORMATION (3) CHANGE ............ 312

FIG. 4.3-121 BTS NAME CHANGE .............................................................................. 313

FIG. 4.3-122 PCF TIMER CHANGE.............................................................................. 314

FIG. 4.3-123 PCP/PMP ADDRESS CHANGE................................................................ 315

FIG. 4.3-124 PIP ADDRESS CHANGE.......................................................................... 316

FIG. 4.3-125 PCF PARAMETER CHANGE ................................................................... 317

FIG. 4.3-126 BSS CONFIGURATION INFORMATION DISPLAY .................................. 330

FIG. 4.3-127 SMP CONFIGURATION INFORMATION DISPLAY ................................. 331

FIG. 4.3-128 VMP CONFIGURATION INFORMATION DISPLAY................................. 332

FIG. 4.3-129 BTS CONFIGURATION INFORMATION DISPLAY.................................. 333

FIG. 4.3-130 DBPA CHIP CONFIGURATION INFORMATION DISPLAY...................... 334

FIG. 4.3-131 OVHD CHANNEL CONFIGURATION INFORMATION DISPLAY............. 335

FIG. 4.3-132 PDSN CONFIGURATION INFORMATION DISPLAY ............................... 336

FIG. 4.3-133 BTS CONFIGURATION INFORMATION CHANGE DISPLAY.................. 339

FIG. 4.3-134 CHANNEL CARD CHIP CONFIGURATION INFORMATION (1) CHANGE

DISPLAY................................................................................................................. 341

FIG. 4.3-135 CHANNEL CARD CHIP CONFIGURATION INFORMATION (2) CHANGE

DISPLAY................................................................................................................. 343

FIG. 4.3-136 PDSN CONFIGURATION ADDITION DISPLAY..................................... 344

FIG. 4.3-137 PDSN CONFIGURATION DELETION DISPLAY.................................... 345

FIG. 4.3-138 PDSN CONFIGURATION CHANGE DISPLAY ....................................... 346

FIG. 4.3-139 PDSN NODE ADDITION DISPLAY ........................................................ 347

FIG. 4.3-140 PDSN NODE DELETION DISPLAY ....................................................... 348

SMD-011-PMA210

Page:11(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.3-141 PDSN NODE CHANGE DISPLAY .......................................................... 349

FIG. 4.3-142 BSC NODE MOVEMENT DISPLAY....................................................... 350

FIG. 4.3-143 SMP NODE MOVEMENT DISPLAY....................................................... 352

FIG. 4.3-144 VMP NODE MOVEMENT DISPLAY ...................................................... 353

FIG. 4.3-145 BTS ID MOVEMENT DISPLAY ............................................................. 354

FIG. 4.3-146 BTS TRUNK MOVEMENT DISPLAY .................................................... 355

FIG. 4.3-147 LICA LINK MOVEMENT DISPLAY ....................................................... 356

FIG. 4.3-148 OVHD CHANNEL CONFIGURATION INFORMATION MOVEMENT

DISPLAY................................................................................................................. 357

FIG. 4.3-149 PCF CONFIGURATION ADDITION DISPLAY ....................................... 360

FIG. 4.3-150 PCF CONFIGURATION DELETION DISPLAY....................................... 361

FIG. 4.3-151 SMP CONFIGURATION ADDITION DISPLAY....................................... 362

FIG. 4.3-152 SMP CONFIGURATION DELETION DISPLAY...................................... 363

FIG. 4.3-153 VMP CONFIGURATION ADDITION DISPLAY ...................................... 364

FIG. 4.3-154 VMP CONFIGURATION DELETION DISPLAY...................................... 365

FIG. 4.3-155 BTS CONFIGURATION DELETION DISPLAY ...................................... 367

FIG. 4.3-156 FA CONFIGURATION ADDITION DISPLAY ......................................... 370

FIG. 4.3-157 FA CONFIGURATION DELETION DISPLAY......................................... 371

FIG. 4.3-158 CAN PVC CONFIGURATION ADDITION DISPLAY .............................. 374

FIG. 4.3-159 CAN PVC CONFIGURATION DELETION DISPLAY.............................. 375

FIG. 4.3-160 CPN PVC CONFIGURATION ADDITION DISPLAY............................... 376

FIG. 4.3-161 CPN PVC CONFIGURATION DELETION DISPLAY .............................. 377

FIG. 4.3-162 BSC PVC CONFIGURATION ADDITION DISPLAY ............................... 378

FIG. 4.3-163 BSC PVC CONFIGURATION DELETION DISPLAY................................. 379

FIG. 4.4-1 RESULT OF CAN PROCESSOR STATUS DISPLAY COMMAND ................ 380

FIG. 4.4-2 RESULT OF BSC PROCESSOR STATUS DISPLAY .................................... 381

FIG. 4.4-3 RESULT OF BTS PROCESSOR STATUS DISPLAY COMMAND................. 381

FIG. 4.4-4 RESULT OF PROCESSOR RESTART COMMAND....................................... 382

FIG. 4.4-5 CAN PROCESSOR H/W COMMAND RESULT............................................. 383

FIG. 4.4-6 BSC PROCESSOR H/W COMMAND RESULT.............................................. 384

FIG. 4.4-7 BTS PROCESSOR H/W RESET(ISOLATION) COMMAND DISPLAY RESULT

.............................................................................................................................. . 384

FIG. 4.4-8 PROCESSOR SWITCH OVER(SWITCH) COMMAND DISPLAY RESULT .... 385

FIG. 4.4-9 RESULT OF NETWORK STATUS DISPLAY COMMAND............................ 387

FIG. 4.4-10 RESULT OF ALPA NETWORK STATUS DISPLAY................................... 387

FIG. 4.4-11 RESULT OF PDSN NODE STATUS DISPLAY .......................................... 388

FIG. 4.4-12 RESULT OF PCFU NETWORK STATUS DISPLAY COMMAND ............... 388

SMD-011-PMA210

Page:12(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.4-13 RESULT OF ALPA NETWORK BLOCK COMMAND ................................. 389

FIG. 4.4-14 RESULT OF ALPA NETWORK UNBLOCK COMMAND ............................ 390

FIG. 4.4-15 RESULT OF CAN DEVICE STATUS DISPLAY COMMAND...................... 392

FIG. 4.4-16 RESULT OF GPS(CAN) STATUS DISPLAY COMMAND........................... 393

FIG. 4.4-17 RESULT OF H/W RESET CAN DEVICE COMMAND ................................ 394

FIG. 4.4-18 RESULT OF BSC DEVICE STATUS DISPLAY.......................................... 395

FIG. 4.4-19 RESULT OF SLPA STATUS DISPLAY COMMAND .................................. 395

FIG. 4.4-20 RESULT OF VCPA STATUS DISPLAY COMMAND.................................. 396

FIG. 4.4-21 RESULT OF E1 LINK STATUS DISPLAY COMMAND.............................. 397

FIG. 4.4-22 RESULT OF TS NETWORK LINK STATUS DISPLAY COMMAND .......... 397

FIG. 4.4-23 RESULT OF VCE(VOCODER CHANNEL ELEMENT) STATUS DISPLAY

COMMAND ............................................................................................................. 398

FIG. 4.4-24 RESULT OF SLPA BLOCK COMMAND..................................................... 399

FIG. 4.4-25 RESULT OF SLPA UNBLOCK COMMAND ............................................... 399

FIG. 4.4-26 RESULT OF VCPA BLOCK COMMAND.................................................... 400

FIG. 4.4-27 RESULT OF VCPA UNBLOCK COMMAND............................................... 401

FIG. 4.4-28 RESULT OF VLIA BLOCK COMMAND ..................................................... 401

FIG. 4.4-29 RESULT OF VLIA UNBLOCK COMMAND ................................................ 402

FIG. 4.4-30 RESULT OF BSC DEVICE H/W RESET COMMAND ................................. 403

FIG. 4.4-31 RESULT OF H/W RESET ALPA COMMAND............................................. 403

FIG. 4.4-32 RESULT OF BTS DEVICE STATUS DISPLAY COMMAND ...................... 404

FIG. 4.4-33 RESULT OF FA STATUS DISPLAY COMMAND....................................... 405

FIG. 4.4-34 RESULT OF BLOCK DBPA COMMAND.................................................... 406

FIG. 4.4-35 RESULT OF UNBLOCK DBPA COMMAND............................................... 407

FIG. 4.4-36 RESULT OF BLOCK OVERHEAD CHANNEL ELEMENT DISPLAY .......... 407

FIG. 4.4-37 RESULT OF UNBLOCK OVERHEAD CHANNEL ELEMENT .................... 408

FIG. 4.4-38 RESULT OF H/W RESET BTS DEVICE COMMAND................................. 409

FIG. 4.4-39 RESULT OF H/W RESET LPA DEVICE COMMAND ................................. 409

FIG. 4.4-40 RESULT OF LPA COMBINER H/W RESET COMMAND............................ 410

FIG. 4.4-41 RESULT OF BTS SHELF POWER H/W RESET COMMAND ..................... 411

FIG. 4.4-42 RESULT INHIBITED STATUS MESSAGE DISPLAY COMMAND ........... 413

FIG. 4.4-43 RESULT OF STATUS MESSAGE DISPLAY INHIBITION COMMAND ...... 413

FIG. 4.4-44 RESULT OF INHIBITED MESSAGE DISPLAY ALLOW COMMAND ......... 414

FIG. 4.4-45 RESULT OF PROCESSOR OVERLOAD STATUS DISPLAY COMMAND... 415

FIG. 4.4-46 RESULT OF OVERLOAD THRESHOLD VALUE DISPLAY COMMAND .... 416

FIG. 4.4-47 RESULT OF OVERLOAD THRESHOLD VALUE CHANGE COMMAND .... 417

FIG. 4.4-48 RESULT OF OVERLOAD GENERATION TEST COMMAND..................... 417

SMD-011-PMA210

Page:13(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.4-49 RESULT OF OVERLOAD GENERATION TEST STOP COMMAND........... 418

FIG. 4.4-50 COMMAND TO DETERMINE WHETHER TO PERFORM THE OVERLOAD

GENERATION TEST .............................................................................................. 419

FIG. 4.5-1 RESULT OF TEST INHIBIT COMMAND EXECUTION ............................... 421

FIG. 4.5-2 RESULT OF TEST ALLOW COMMAND EXECUTION ................................ 422

FIG. 4.5-3 RESULT OF TEST INHIBIT/ALLOW LIST DISPLAY COMMAND EXECUTION

.............................................................................................................................. . 423

FIG. 4.5-4 RESULT OF CE BIT TEST EXECUTION .................................................... 425

FIG. 4.5-5 RESULT OF ON-DEMAND VOCODER TEST(CHANNEL TYPE) EXECUTION

.............................................................................................................................. . 428

FIG. 4.5-6 RESULT OF ON-DEMAND VOCODER TEST(DSP TYPE) EXECUTION .... 429

FIG. 4.5-7 RESULT OF ON-LINE VOCODER TEST PARAMETER CHANGE COMMAND

EXECUTION ........................................................................................................... 430

FIG. 4.5-8 RESULT OF ON-LINE TEST AT THE TIME OF ON-LINE VOCODER TEST

EXECUTION ........................................................................................................... 430

FIG. 4.5-9 RESULT OF ON-LINE VOCODER TEST PARAMETER DISPLAY COMMAND

EXECUTION ........................................................................................................... 431

FIG. 4.5-10 ON-LINE VOCODER TEST RESULT DISPLAY COMMAND..................... 432

FIG. 4.5-11 ON-LINE VOCODER TEST END COMMAND, STATUS DISPLAY

COMMAND EXECUTION RESULT......................................................................... 433

FIG. 4.5-12 RESULT OF TRUNK BER TEST PERFORMANCE.................................... 435

FIG. 4.5-13 RESULT OF PING TEST PERFORMANCE................................................ 436

FIG. 4.5-14 RESULT OF IPC TEST PERFORMANCE .................................................. 437

FIG. 4.5-15 RESULT OF ATM PATH(PM) TEST PERFORMANCE.............................. 438

FIG. 4.5-16 RESULT OF ATM PATH(CC) TEST PERFORMANCE .............................. 439

FIG. 4.5-17 RESULT OF ATM PATH(LB) TEST EXECUTION .................................... 440

FIG. 4.5-18 BSC VIRTUAL CALL SETUP COMMAND INTERM DISPLAY .................. 443

FIG. 4.5-19 CONSOLE WINDOW DISPLAY AT THE SETUP OF BSC VIRTUAL CALL443

FIG. 4.5-20 DISPLAY AT THE TERMINATION OF BSC VIRTUAL CALL................... 444

FIG. 4.5-21 RESULT OF BSC VIRTUAL CALL RELEASE COMMAND EXECUTION .. 444

FIG. 4.5-22 PRESENTLY REGISTERED TESTING MS DISPLAY ................................ 445

FIG. 4.5-23 TESTING MS INSERT RESULT DISPLAY ................................................ 446

FIG. 4.5-24 DELETE MS EXECUTION RESULT.......................................................... 446

FIG. 4.5-25 TRAFFIC PATH SETUP COMMAND EXECUTION RESULT

DISPLAY(INTERM WINDOW)................................................................................. 448

FIG. 4.5-26 TRAFFIC PATH SETUP COMMAND EXECUTION RESULT

DISPLAY(CONSOLE WINDOW).............................................................................. 448

SMD-011-PMA210

Page:14(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.5-27 TRAFFIC PATH RELEASE COMMAND EXECUTION RESULT

DISPLAY(INTERM WINDOW)................................................................................. 449

FIG. 4.5-28 TRAFFIC PATH RELEASE COMMAND EXECUTION RESULT

DISPLAY(CONSOLE WINDOW).............................................................................. 449

FIG. 4.5-29 CALL TRACE START COMMAND INPUT SCREEN ................................. 451

FIG. 4.5-30 CALL TRACE DISPLAY IN THE PROCESS OF CALL SET....................... 452

FIG. 4.5-31 DISPLAY OF CALL SET PROCESS AND ELEMENTS OF COMMUNICATION

QUALITY................................................................................................................ 453

FIG. 4.5-32 DISPLAY OF COMMUNICATION QUALITY AND RELEASE REASON ..... 454

FIG. 4.5-33 CALL TRACE STOP RESULT................................................................... 454

FIG. 4.5-34 TERMINAL DISPLAY IN USE OF CALL TRACE....................................... 455

FIG. 4.5-35 RESULT OF THE NUMBER OF DATA CALL USER DISPLAY ................. 456

FIG. 4.5-36 RESULT OF DATA CALL USER STATUS DISPLAY BY IMSI .................. 457

FIG. 4.5-37 IOS MESSAGE DISPLAY START RESULT ............................................... 458

FIG. 4.5-38 IOS DISPLAY MESSAGE ........................................................................... 459

FIG. 4.5-39 STOP RESULT OF IOS MESSAGE DISPLAY FUNCTION......................... 460

FIG. 4.5-40 POWER MONITORING START RESULT................................................... 461

FIG. 4.5-41 POWER MONITORING RESULT................................................................ 462

FIG. 4.5-42 POWER MONITORING STOP RESULT ..................................................... 462

FIG. 4.6-1 SIGNALING POINT INFORMATION DISPLAY............................................ 466

FIG. 4.6-2 CHANGE OF INTRA-SWITCHING OFFICE SIGNALING POINT ................ 466

FIG. 4.6-3 CHANGE OF REMOTE SWITCHING OFFICE SIGNALING POINT.............. 467

FIG. 4.6-4 ACTIVATION OF SIGNALING LINK SET ................................................... 468

FIG. 4.6-5 DEACTIVATION OF SIGNALING LINK SET .............................................. 468

FIG. 4.6-6 SIGNALING LINK CREATE......................................................................... 469

FIG. 4.6-7 DELETION OF SIGNALING LINK ............................................................... 470

FIG. 4.6-8 ACTIVATION OF SIGNALING LINK ........................................................... 471

FIG. 4.6-9 DEACTIVATION OF SIGNALING LINK ...................................................... 472

FIG. 4.6-10 SIGNALING LINK INFORMATION DISPLAY ............................................ 472

FIG. 4.6-11 SIGNALING LINK INHIBIT........................................................................ 473

FIG. 4.6-12 SIGNAL LINK ALLOW............................................................................... 474

FIG. 4.6-13 SIGNALING TERMINAL GENERATION .................................................... 474

FIG. 4.6-14 SIGNALING TERMINAL DELETION ......................................................... 475

FIG. 4.6-15 DISPLAY OF SIGNALING TERMINAL INFORMATION............................. 475

FIG. 4.6-16 SIGNALING DATA LINK GENERATION................................................... 476

FIG. 4.6-17 SIGNALING DATA LINK DELETION ........................................................ 477

FIG. 4.6-18 SIGNALING DATA LINK INFORMATION DISPLAY ................................. 478

SMD-011-PMA210

Page:15(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.6-19 SCCP NETWORK CONFIGURATION DATA DISPLAY.............................. 478

FIG. 4.6-20 SCCP LOCAL SUBSYSTEM STATE DATA DISPLAY............................... 479

FIG. 4.6-21 SIGNALING LINK STATUS DISPLAY....................................................... 480

FIG. 4.6-22 SIGNALING TERMINAL STATUS DISPLAY............................................. 481

FIG. 4.6-23 SIGNALING LINK SET STATUS DISPLAY............................................... 481

FIG. 4.6-24 MTP LEVEL2 TIMER DISPLAY ................................................................ 482

FIG. 4.6-25 MTP LEVEL2 TIMER CHANGE ................................................................ 483

FIG. 4.6-26 MTP LEVEL3 TIMER DISPLAY ................................................................ 484

FIG. 4.6-27 MTP LEVEL E 3 TIMER CHANGE............................................................ 485

FIG. 4.6-28 SCCP TIMER CHANGE ............................................................................. 486

FIG. 4.6-29 SIGNALING LINK TEST ........................................................................... 487

FIG. 4.6-30 SIGNALING TERMINAL TEST.................................................................. 488

FIG. 4.6-31 TEST CYCLE DISPLAY............................................................................. 488

FIG. 4.6-32 TEST CYCLE CHANGE............................................................................. 489

FIG. 4.6-33 OUTPUT POSSIBLE STATUS MESSAGE DISPLAY................................. 489

FIG. 4.6-34 STATUS MESSAGE DISPLAY ALLOWED ................................................ 490

FIG. 4.6-35 STATUS MESSAGE DISPLAY INHIBIT .................................................... 490

FIG. 4.7-1 CONFIGURATION OF STATISTICS COMMAND ........................................ 493

FIG. 4.7-2 TRAFFIC STATISTICS FUNCTION............................................................ 493

FIG. 4.7-3 TRAFFIC STATISTICS DATA DISPLAY RESULT...................................... 495

FIG. 4.7-4 HOURLY TRAFFIC STATISTICS DISPLAY RESULT ................................. 496

FIG. 4.7-5 HANDOFF RELATED STATISTICS FUNCTION......................................... 497

FIG. 4.7-6 HANDOFF STATISTICS.............................................................................. 499

FIG. 4.7-7 SOFTER HANDOFF STATISTICS DISPLAY............................................... 500

FIG. 4.7-8 SOFT HANDOFF DISPLAY RESULT .......................................................... 501

FIG. 4.7-9 HARD HANDOFF STATISTICS DISPLAY................................................... 502

FIG. 4.7-10 STATISTICS FUNCTION RELATED TO CALL ........................................ 503

FIG. 4.7-11 CHANNEL STATISTICS FUNCTION ........................................................ 504

FIG. 4.7-12 VOCODER STATISTICS OUTPUT............................................................ 505

FIG. 4.7-13 NETWORK STATISTICS OUTPUT RESULTS.......................................... 506

FIG. 4.7-14 RADIO CHANNEL STATISTICS OUTPUT RESULTS............................... 507

FIG. 4.7-15 PROCESSOR STATISTICS DISPLAY RESULTS ....................................... 508

FIG. 4.7-16 SELECTOR STATISTICS DISPLAY RESULTS ......................................... 509

FIG. 4.7-17 CALL DELAY PERFORMANCE STATISTICS DISPLAY RESULTS........... 510

FIG. 4.7-18 PAGING STATISTICS DISPLAY RESULTS .............................................. 511

FIG. 4.7-19 CAI STATISTICS DISPLAY RESULTS...................................................... 512

FIG. 4.7-20 NO.7 SIGNALING STATISTICS DISPLAY RESULTS................................ 513

SMD-011-PMA210

Page:16(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.7-21 RTD STATISTICS DISPLAY RESULTS .................................................... 514

FIG. 4.7-22 RF MIN/MAX STATISTICS FUNCTION DISPLAY RESULTS................... 515

FIG. 4.7-23 PACKET STATISTICS FUNCTION........................................................... 515

FIG. 4.7-24 PACKET DATA STATISTICS DISPLAY RESULTS .................................. 516

FIG. 4.7-25 PACKET CONTROL STATISTICS FUNCTION RESULTS DISPLAY ........ 517

FIG. 4.7-26 PACKET HANDOFF STATISTICS FUNCTION DISPLAY RESULTS ........ 518

FIG. 4.7-27 DISPLAY RESULTS OF STATISTICS LIST UNDER EXECUTION ........... 518

FIG. 4.7-28 RESULTS OF CHANGING ON LINE STATISTICS PERIOD ...................... 520

FIG. 4.8-1 DISPLAY RESULT OF THE DISPLAY INHIBITED ALARM MESSAGE LIST

.............................................................................................................................. . 523

FIG. 4.8-2 DISPLAY RESULT OF THE DISPLAY COMMAND FOR AUDIBLE ALARM

STATUS ................................................................................................................. 524

FIG. 4.8-3 DISPLAY RESULT OF THE LIST FOR THE DISPLAY INHIBITED FAULT

MESSAGE............................................................................................................... 524

FIG. 4.8-4 DISPLAY RESULT OF DISPLAY COMMAND FOR THE PRESENT ALARM

STATUS ................................................................................................................. 525

FIG. 4.8-5 DISPLAY RESULT OF DISPLAY COMMAND FOR PRESENT ALARM

STATUS ................................................................................................................. 526

FIG. 4.8-6 DISPLAY RESULT OF DISPLAY COMMAND FOR THE SUPPRESSED ALARM

MESSAGE............................................................................................................... 526

FIG. 4.8-7 DISPLAY RESULT OF DISPLAY COMMAND FOR INFORMATION ABOUT

THE ALARM MESSAGE ......................................................................................... 527

FIG. 4.8-8 DISPLAY RESULT OF DISPLAY COMMAND FOR THE INFORMATION

ABOUT ALARM LIST............................................................................................. 528

FIG. 4.8-9 DISPLAY RESULT OF DISPLAY COMMAND FOR THE SUPPRESS FAULT

MESSAGE LIST ...................................................................................................... 529

FIG. 4.8-10 DISPLAY RESULT OF DISPLAY INHIBITION FOR ALARM MESSAGE.. 530

FIG. 4.8-11 DISPLAY RESULT OF INHIBITION COMMAND FOR AUDIBLE ALARM 530

FIG. 4.8-12 DISPLAY RESULT OF INHIBITION/ALLOWANCE FOR FAULT MESSAGE

DISPLAY................................................................................................................. 531

FIG. 4.8-13 DISPLAY RESULT OF THE SUPPRESS ALARM MESSAGE COMMAND . 532

FIG. 4.8-14 DISPLAY RESULT FOR THE FAULT MESSAGE SUPPRESS COMMAND

.............................................................................................................................. . 532

FIG. 4.8-15 DISPLAY RESULT OF ALLOWANCE FOR ALARM MESSAGE DISPLAY

INHIBITION ............................................................................................................ 533

FIG. 4.8-16 DISPLAY RESULT OF ALLOWANCE COMMAND FOR INHIBITED AUDIBLE

ALARM ................................................................................................................... 534

SMD-011-PMA210

Page:17(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.8-17 DISPLAY RESULT FOR ALLOWING FAULT MESSAGE DISPLAY

INHIBITION ............................................................................................................ 534

FIG. 4.8-18 DISPLAY RESULT OF RELEASE COMMAND FOR SUPPRESSED ALARM

MESSAGE............................................................................................................... 535

FIG. 4.8-19 DISPLAY RESULT OF RELEASE COMMAND FOR SUPPRESSED FAULT

MESSAGE............................................................................................................... 536

FIG. 4.9-1 MANAGER WINDOW................................................................................... 546

FIG. 4.9-2 LOGIN WINDOW.......................................................................................... 547

FIG. 4.9-3 INTERM CONFIGURATION......................................................................... 548

FIG. 4.9-4 CDM TEAR-OFF ......................................................................................... 549

FIG. 4.9-5 POP-UP WINDOW....................................................................................... 549

FIG. 4.9-6 BATCH JOB SCREEN.................................................................................. 550

FIG. 4.9-7 BATCH JOB INPUT..................................................................................... 554

FIG. 4.9-8 BATCH JOB MODIFICATION...................................................................... 556

FIG. 4.9-9 BATCH JOB DELETION.............................................................................. 557

FIG. 4.9-10 BATCH JOB STATUS DISPLAY................................................................ 557

FIG. 4.9-11 CONSOLE WINDOW.................................................................................. 558

FIG. 4.9-12 CTRL START ICON................................................................................... 559

FIG. 4.9-13 CONTROLLER WINDOW........................................................................... 560

FIG. 4.9-14 MESSAGE FILTERING OF CONTROLLER................................................ 560

FIG. 4.9-15 NETWORK MANAGEMENT OF CONTROLLER........................................ 561

FIG. 4.9-16 STMGUI START ICON .............................................................................. 564

FIG. 4.9-17 STMGUI MAIN SCREEN ........................................................................... 564

FIG. 4.9-18 DISPLAY SCREEN OF BTS NAME............................................................ 565

FIG. 4.9-19 MAIN MENU.............................................................................................. 565

FIG. 4.9-20 ALARM COLOR ......................................................................................... 565

FIG. 4.9-21 STATUS COLOR TONE ............................................................................ 567

FIG. 4.9-22 PROCESSOR STATUS (CAN).................................................................... 567

FIG. 4.9-23 PROCESSOR STATUS (BSC) .................................................................... 567

FIG. 4.9-24 PROCESSOR STATUS (BTS).................................................................... 568

FIG. 4.9-25 BSC SELECTION....................................................................................... 568

FIG. 4.9-26 BTS SELECTION....................................................................................... 568

FIG. 4.9-27 CAN RACK SHAPE.................................................................................... 569

FIG. 4.9-28 BSC RACK................................................................................................. 570

FIG. 4.9-29 BTS RACK................................................................................................. 571

FIG. 4.9-30 CARD CLICK EXAMPLE............................................................................ 572

FIG. 4.9-31 E.G.)DIALOG BOX- CARD INFORMATION............................................... 572

SMD-011-PMA210

Page:18(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.9-32 E.G.)DIALOG BOX-VOCODER ELEMENT STATUS ................................. 573

FIG. 4.9-33 E.G.)DIALOG BOX-DBPA CHIP STATUS................................................. 573

FIG 4.9-34 DISPLAY STATUS BY BOARD ................................................................ 574

FIG. 4.9-35 ALARM DISPLAY BY BOARD. ................................................................ 574

FIG. 4.9-36 NEIGHBOR INITIAL SCREEN ................................................................... 577

FIG. 4.9-37 MAIN MENU SCREEN............................................................................... 578

FIG. 4.9-38 FULL MAP .............................................................................................. 578

FIG. 4.9-39 RANDOM BTS SELECTION ...................................................................... 579

FIG.4.9-40 INITIAL SCREEN (BEFORE SELECTING BTS ) ........................................ 579

FIG. 4.9-41 AFTER SELECTING BTS.......................................................................... 579

FIG. 4.9-42 AFTER SELECTING SECTOR(GREEN: NEIGHBOR). ............................... 579

FIG. 4.9-43 NEIGHBOR INFORMATION SCREEN........................................................ 580

FIG. 4.9-44 INPUTTING NEIGHBOR BELONGS TO MOTHER MSC ........................... 581

FIG. 4.9-45 INPUTTING NEIGHBOR BELONGS TO OTHER MSC .............................. 581

FIG. 4.9-46 DEFAULT VALUE UPON INPUT.............................................................. 582

FIG. 4.9-47 CALL TRACE START ICON...................................................................... 583

FIG. 4.9-48 CALL TRACE INITIAL SCREEN ............................................................... 584

FIG. 4.9-49 CALL INFORMATION................................................................................ 585

FIG. 4.9-50 CALL QUALITY......................................................................................... 585

FIG. 4.9-51 SCH INFORMATION.................................................................................. 586

FIG. 4.9-52 PACKET DATA INFORMATION ............................................................... 586

FIG. 4.9-53 COMMAND WINDOW................................................................................ 586

FIG. 4.9-54 EXAMPLE OF EXPAND FLOW BUTTON.................................................. 587

FIG. 4.9-55 EXAMPLE OF SHRINK FLOW BUTTON................................................... 588

FIG. 4.9-56 VOICE CALL SETUP / ORIGINATION ...................................................... 589

FIG. 4.9-57 VOICE CALL SETUP / TERMINATION..................................................... 590

FIG 4.9-58 PACKET DATA CALL SETUP ................................................................... 591

FIG. 4.9-59 PACKET DATA CALL REACTIVATION / NETWORK INITIATED ........... 592

FIG. 4.9-60 PACKET DATA CALL REACTIVATION / MS INITIATED........................ 593

FIG. 4.9-61 BTS ADDRESS SEARCH WINDOW INITIAL SCREEN .............................. 595

FIG. 4.9-62 FILE INFORMATION DISPLAY ................................................................. 595

FIG. 4.9-63 SEARCHING WITH BSC............................................................................ 596

FIG. 4.9-64 SEARCHING BY BTS ................................................................................ 596

FIG. 4.9-65 SEARCHING WITH BTS NAME-1 ............................................................ 597

FIG. 4.9-66 SEARCHING WITH BTS NAME-2 ............................................................ 597

FIG. 4.9-67 SEARCHING WITH BTS ADDRESS-1....................................................... 598

FIG. 4.9-68 SEARCHING WITH BTS ADDRESS-2....................................................... 598

SMD-011-PMA210

Page:19(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 4.9-69 SEARCHING WITH SEARCH BUTTON..................................................... 600

FIG. 5.1-1 CNP SINGLE FUNCTION FAIL................................................................. 601

FIG. 5.1-2 CNP DUAL FUNCTION FAIL.................................................................... 601

FIG. 5.1-3 CNP SINGLE BOARD OPEN FAIL............................................................. 602

FIG. 5.1-4 CNP DUAL BOARD OPEN FAIL................................................................ 602

FIG. 5.1-5 CAN ASCA SINGLE FUNCTION FAIL ...................................................... 602

FIG. 5.1-6 CAN ASCA DUAL FUNCTION FAIL......................................................... 603

FIG. 5.1-7 CAN ASCA SINGLE BOARD OPEN FAIL.................................................. 603

FIG. 5.1-8 CAN ASCA DUAL OPEN FAIL.................................................................. 603

FIG. 5.1-9 CAN ASIA SINGLE FUNCTION FAIL ....................................................... 604

FIG. 5.1-10 CAN ASIA DUAL FUNCTION FAIL ........................................................ 604

FIG. 5.1-11 CAN ASIA SINGLE BOARD OPEN FAIL ................................................. 604

FIG. 5.1-12 CAN ASIA SINGLE BOARD OPEN FAIL ................................................. 605

FIG. 5.1-13 CAN AOTA FUNCTION FAIL ................................................................. 605

FIG. 5.1-14 CAN AOTA BOARD OPEN FAIL ............................................................. 605

FIG. 5.1-15 CAN ATSA FUNCTION FAIL.................................................................. 606

FIG. 5.1-16 CAN ATSA BOARD OPEN FAIL ............................................................. 606

FIG. 5.1-17 CAMB PRI SINGLE POWER FAIL ........................................................... 606

FIG. 5.1-18 CAMB PRI DUAL POWER FAIL .............................................................. 607

FIG. 5.1-19 CAMB PRI SINGLE POWER OPEN FAIL................................................. 607

FIG. 5.1-20 CAMB PRI DUAL POWER OPEN FAIL.................................................... 607

FIG. 5.1-21 CAN ALARM CABLE OPEN.................................................................... 608

FIG. 5.1-22 CAN PNP SINGLE FUNCTION FAIL....................................................... 608

FIG. 5.1-23 CAN PNP DUAL FUNCTION FAIL.......................................................... 608

FIG. 5.1-24 CAN PNP SINGLE BOARD OPEN FAIL .................................................. 609

FIG. 5.1-25 CAN PNP DUAL BOARD OPEN FAIL ..................................................... 609

FIG. 5.1-26 CPNB ASCA SINGLE FUNCTION FAIL.................................................. 609

FIG. 5.1-27 CPNB ASCA DUAL FUNCTION FAIL..................................................... 610

FIG. 5.1-28 CPNB ASCA SINGLE BOARD OPEN FAIL.............................................. 610

FIG. 5.1-29 CPNB ASCA DUAL BOARD OPEN FAIL................................................. 610

FIG. 5.1-30 CPNB ASIA SINGLE FUNCTION FAIL ................................................... 611

FIG. 5.1-31 CPNB ASIA DUAL FUNCTION FAIL ...................................................... 611

FIG. 5.1-32 CPNB ASIA SINGLE BOARD OPEN FAIL ............................................... 611

FIG. 5.1-33 CPNB ASIA DUAL BOARD OPEN FAIL .................................................. 612

FIG. 5.1-34 CPNB PRI SINGLE POWER FAIL............................................................ 612

FIG. 5.1-35 CPNB PRI DUAL POWER FAIL............................................................... 612

FIG. 5.1-36 CPNB PRI SINGLE POWER OPEN FAIL ................................................. 613

SMD-011-PMA210

Page:20(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-37 CPNB PRI DUAL POWER OPEN FAIL .................................................... 613

FIG. 5.1-38 CPNB ALARM CABLE OPEN .................................................................. 613

FIG. 5.1-39 PCFB PCP SINGLE FUNCTION FAIL..................................................... 614

FIG. 5.1-40 PCFB PCP DUAL FUNCTION FAIL........................................................ 614

FIG. 5.1-41 PCFB PCP SINGLE BOARD OPEN FAIL................................................. 614

FIG. 5.1-42 PCFB PCP DUAL BOARD OPEN FAIL.................................................... 615

FIG. 5.1-43 CPNB(PCP) BCRA SINGLE FUNCTION FAIL......................................... 615

FIG. 5.1-44 CPNB(PCP) BCRA DUAL FUNCTION FAIL............................................ 615

FIG. 5.1-45 CPNB(PCP) BCRA SINGLE BOARD OPEN FAIL..................................... 616

FIG. 5.1-46 CPNB(PCP) BCRA DUAL BOARD OPEN FAIL........................................ 616

FIG. 5.1-47 CPNB(PCP) PIP FUNCTION FAIL .......................................................... 616

FIG. 5.1-48 CPNB(PCP) PIP BOARD OPEN FAIL ...................................................... 617

FIG. 5.1-49 CPNB(PCP) FERA SINGLE FUNCTION FAIL ......................................... 617

FIG. 5.1-50 CPNB(PCP) FERA DUAL FUNCTION FAIL ............................................ 617

FIG. 5.1-51 CPNB(PCP) FERA SINGLE BOARD OPEN FAIL..................................... 618

FIG. 5.1-52 CPNB(PCP) FERA DUAL BOARD OPEN FAIL........................................ 618

FIG. 5.1-53 CPNB(PCP) FETA FUNCTION FAIL....................................................... 618

FIG. 5.1-54 CPNB(PCP) FETA BOARD OPEN FAIL .................................................. 619

FIG. 5.1-55 CPNB(PCP) PRI SINGLE POWER FAIL................................................... 619

FIG. 5.1-56 CPNB(PCP) PRI DUAL POWER FAIL...................................................... 619

FIG. 5.1-57 CPNB(PCP) PRI SINGLE POWER OPEN FAIL ........................................ 620

FIG. 5.1-58 CPNB(PCP) PRI DUAL POWER OPEN FAIL ........................................... 620

FIG. 5.1-59 CPNB(PCP) ALARM CABLE OPEN......................................................... 620

FIG. 5.1-60 LINK FAIL BETWEEN CPNB(PCP) FERA AND FETA ........................... 621

FIG. 5.1-61 LINK FAIL BETWEEN CPNB(PCP) FERA AND FETA ........................... 621

FIG. 5.1-62 LINK FAIL BETWEEN CPNB(PCP) FETA AND PDSN ........................... 621

FIG. 5.1-63 PCFB PCP 1PPS CLOCK FAIL................................................................ 622

FIG. 5.1-64 PCFB PCP 10MHZ CLOCK FAIL............................................................. 622

FIG. 5.1-65 PCFB(PMP) PMP SINGLE FUNCTION FAIL........................................... 622

FIG. 5.1-66 PCFB(PMP) PMP DUAL FUNCTION FAIL.............................................. 623

FIG. 5.1-67 PCFB(PMP) PMP SINGLE BOARD OPEN FAIL ...................................... 623

FIG. 5.1-68 PCFB(PMP) PMP DUAL BOARD OPEN FAIL ......................................... 623

FIG. 5.1-69 TGDB GPSR SINGLE FUNCTION FAIL.................................................. 624

FIG. 5.1-70 TGDB GPSR DUAL FUNCTION FAIL ..................................................... 624

FIG. 5.1-71 TGDB GPSR SINGLE POWER FAIL ........................................................ 625

FIG. 5.1-72 TGDB GPSR DUAL POWER FAIL ........................................................... 625

FIG. 5.1-73 TGDB GPSR SINGLE BOARD OPEN FAIL.............................................. 625

SMD-011-PMA210

Page:21(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-74 TGDB GPSR DUAL BOARD OPEN FAIL................................................. 626

FIG. 5.1-75 TGDB GPSD SINGLE FUNCTION FAIL.................................................. 626

FIG. 5.1-76 TGDB GPSD DUAL FUNCTION FAIL..................................................... 626

FIG. 5.1-77 TGDB GPSD SINGLE POWER FAIL........................................................ 627

FIG. 5.1-78 TGDB GPSD DUAL POWER FAIL........................................................... 627

FIG. 5.1-79 TGDB AMP ABNORMAL......................................................................... 627

FIG. 5.1-80 TGDB GPSR ALARM CABLE OPEN........................................................ 628

FIG. 5.1-81 TGDB GPSD ALARM CABLE OPEN ....................................................... 628

FIG. 5.1-82 TGDB GPSR CONTROL CABLE OPEN ................................................... 628

FIG. 5.1-83 CAN RACK FAN FAIL............................................................................. 629

FIG. 5.1-84 CCSB CCP SINGLE FUNCTION FAIL..................................................... 629

FIG. 5.1-85 CCSB CCP DUAL FUNCTION FAIL........................................................ 629

FIG. 5.1-86 CCSB CCP SINGLE BOARD OPEN FAIL................................................. 630

FIG. 5.1-87 CCSB CCP DUAL BOARD OPEN FAIL.................................................... 630

FIG. 5.1-88 CCSB SCP SINGLE FUNCTION FAIL..................................................... 630

FIG. 5.1-89 CCSB SCP DUAL FUNCTION FAIL........................................................ 631

FIG. 5.1-90 CCSB SCP SINGLE BOARD OPEN FAIL................................................. 631

FIG. 5.1-91 CCSB SCP DUAL BOARD OPEN FAIL.................................................... 631

FIG. 5.1-92 CCSB STIA FUNCTION FAIL ................................................................. 632

FIG. 5.1-93 CCSB STIA BOARD OPEN FAIL ............................................................. 632

FIG. 5.1-94 CCSB PRI SINGLE POWER FAIL ............................................................ 632

FIG. 5.1-95 CCSB PRI DUAL POWER FAIL ............................................................... 633

FIG. 5.1-96 CCSB PRI SINGLE POWER OPEN FAIL.................................................. 633

FIG. 5.1-97 CCSB PRI DUAL POWER OPEN FAIL..................................................... 633

FIG. 5.1-98 CCSB ABID BOARD OPEN...................................................................... 634

FIG. 5.1-99 CCSB 1PPS CLOCK FAIL ....................................................................... 634

FIG. 5.1-100 CCSB 10MHZ CLOCK FAIL .................................................................. 634

FIG. 5.1-101 CCSB STIA SHW LINK FAIL ................................................................ 635

FIG. 5.1-102 CCSB ALARM CABLE OPEN ................................................................ 635

FIG. 5.1-103 ASMB NCP SINGLE FUNCTION FAIL.................................................. 635

FIG. 5.1-104 ASMB NCP DUAL FUNCTION FAIL..................................................... 635

FIG. 5.1-105 ASMB NCP SINGLE BOARD OPEN FAIL.............................................. 636

FIG. 5.1-106 ASMB NCP DUAL BOARD OPEN FAIL................................................. 636

FIG. 5.1-107 ASMB ASCA SINGLE FUNCTION FAIL................................................ 636

FIG. 5.1-108 ASMB ASCA DUAL FUNCTION FAIL................................................... 637

FIG. 5.1-109 ASMB ASCA SINGLE BOARD OPEN FAIL ........................................... 637

FIG. 5.1-110 ASMB ASCA DUAL BOARD OPEN FAIL .............................................. 637

SMD-011-PMA210

Page:22(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-111 ASMB ASIA SINGLE FUNCTION FAIL................................................. 638

FIG. 5.1-112 ASMB ASIA DUAL FUNCTION FAIL.................................................... 638

FIG. 5.1-113 ASMB ASIA SINGLE BOARD FAIL ....................................................... 638

FIG. 5.1-114 ASMB ASIA DUAL BOARD OPEN FAIL................................................ 639

FIG. 5.1-115 ASMB ATSA FUNCTION FAIL ............................................................. 639

FIG. 5.1-116 ASMB ATSA BOARD OPEN FAIL......................................................... 639

FIG. 5.1-117 ASMB PRI SINGLE POWER FAIL.......................................................... 640

FIG. 5.1-118 ASMB PRI DUAL POWER FAIL............................................................. 640

FIG. 5.1-119 ASMB PRI SINGLE POWER OPEN FAIL............................................... 640

FIG. 5.1-120 ASMB PRI DUAL POWER OPEN FAIL.................................................. 641

FIG. 5.1-121 ASMB ALARM CABLE OPEN................................................................ 641

FIG. 5.1-122 ASLB ALP SINGLE FUNCTION FAIL................................................... 641

FIG. 5.1-123 ASLB ALP DUAL FUNCTION FAIL...................................................... 642

FIG. 5.1-124 ASLB ALP SINGLE BOARD OPEN FAIL............................................... 642

FIG. 5.1-125 ASLB ALP DUAL BOARD OPEN FAIL.................................................. 642

FIG. 5.1-126 ASLB ALMA SINGLE FUNCTION FAIL................................................ 643

FIG. 5.1-127 ASLB ALP DUAL FUNCTION FAIL...................................................... 643

FIG. 5.1-128 ASLB ALP SINGLE BOARD OPEN FAIL............................................... 643

FIG. 5.1-129 ASLB ALP DUAL BOARD OPEN FAIL.................................................. 644

FIG. 5.1-130 ASLB ALPA FUNCTION FAIL .............................................................. 644

FIG. 5.1-131 ASLB ALPA BOARD OPEN FAIL .......................................................... 644

FIG. 5.1-132 ASLB PRI SINGLE POWER FAIL .......................................................... 645

FIG. 5.1-133 ASLB PRI DUAL POWER FAIL ............................................................. 645

FIG. 5.1-134 ASLB PRI SINGLE POWER OPEN FAIL................................................ 645

FIG. 5.1-135 ASLB PRI DUAL POWER OPEN FAIL................................................... 646

FIG. 5.1-136 ASLB ALARM CABLE OPEN ................................................................ 646

FIG. 5.1-137 ASLB ALPA LINK FAIL((LOS).............................................................. 646

FIG. 5.1-138 ASLB ALPA LINK FAIL((OOF).............................................................. 647

FIG. 5.1-139 ASLB ALPA LINK FAIL((AIS)............................................................... 647

FIG. 5.1-140 ASLB ALPA LINK FAIL((RAI)............................................................... 647

FIG. 5.1-141 SLB SMP FUNCTION FAIL................................................................... 648

FIG. 5.1-142 SLB SMP BOARD OPEN FAIL............................................................... 648

FIG. 5.1-143 SLB SLPA FUNCTION FAIL ................................................................. 648

FIG. 5.1-144 SLB SLPA BOARD OPEN FAIL............................................................. 649

FIG. 5.1-145 SLB PRI POWER FAIL........................................................................... 649

FIG. 5.1-146 SLB PRI POWER OPEN FAIL................................................................ 649

FIG. 5.1-147 SLB ALARM CABLE OPEN................................................................... 650

SMD-011-PMA210

Page:23(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-148 SLB SMP CLOCK FAIL ......................................................................... 650

FIG. 5.1-149 SLB SMP SAID OPEN FAIL .................................................................. 650

FIG. 5.1-150 VCB VMP FUNCTION FAIL.................................................................. 651

FIG. 5.1-151 VCB VMP BOARD OPEN FAIL ............................................................. 651

FIG. 5.1-152 VCB VCPA FUNCTION FAIL................................................................ 651

FIG. 5.1-153 VCB VCPA BOARD OPEN FAIL............................................................ 652

FIG. 5.1-154 VCB VLIA FUNCTION FAIL ................................................................. 652

FIG. 5.1-155 VCB VLIA BOARD OPEN FAIL............................................................. 652

FIG. 5.1-156 VCB VLIA LINK FAIL(REMOTE ERROR).............................................. 653

FIG. 5.1-157 VCB VLIA LINK FAIL(LOCAL ERROR)................................................. 653

FIG. 5.1-158 VCB VLIA LINK FAIL(SLIP ERROR)..................................................... 653

FIG. 5.1-159 VCB VLIA LINK FAIL(BIT ERROR) ...................................................... 654

FIG. 5.1-160 VCB PRI POWER FAIL.......................................................................... 654

FIG. 5.1-161 VCB PRI POWER OPEN FAIL ............................................................... 654

FIG. 5.1-162 VCB ALARM CABLE OPEN .................................................................. 654

FIG. 5.1-163 VCB VMP CLOCK CABLE OPEN FAIL ................................................. 655

FIG. 5.1-164 VCB SAID BOARD OPEN ...................................................................... 655

FIG. 5.1-165 VCB RACK FAN FAIL........................................................................... 655

FIG. 5.1-166 BSPB BSP SINGLE FUNCTION FAIL ................................................... 656

FIG. 5.1-167 BSPB BSP DUAL FUNCTION FAIL ...................................................... 656

FIG. 5.1-168 BSPB BSP SINGLE BOARD OPEN FAIL ............................................... 656

FIG. 5.1-169 BSPB BSP DUAL BOARD OPEN FAIL.................................................. 657

FIG. 5.1-170 BSPB PRI SINGLE POWER FAIL .......................................................... 657

FIG. 5.1-171 BSPB PRI DUAL POWER FAIL ............................................................. 657

FIG. 5.1-172 BSPB PRI SINGLE POWER OPEN FAIL................................................ 658

FIG. 5.1-173 BSPB PRI DUAL POWER OPEN FAIL................................................... 658

FIG. 5.1-174 BSPB BSP 1PPS CLOCK FAIL.............................................................. 658

FIG. 5.1-175 BSPB BSP 10MHZ CLOCK FAIL........................................................... 659

FIG, 5.1-176 BANB ARIA FUNCTION FAIL............................................................... 659

FIG. 5.1-177 BANB ARIA BOARD OPEN FAIL .......................................................... 659

FIG. 5.1-178 BANB BPPA FUNCTION FAIL.............................................................. 660

FIG. 5.1-179 BANB BPPA BOARD OPEN FAIL ......................................................... 660

FIG. 5.1-180 BANB BCRA SINGLE FUNCTION FAIL................................................ 660

FIG. 5.1-181 BANB BCRA DUAL FUNCTION FAIL................................................... 661

FIG. 5.1-182 BANB BCRA SINGLE BOARD OPEN FAIL............................................ 661

FIG. 5.1-183 BANB BCRA DUAL BOARD OPEN FAIL .............................................. 661

FIG. 5.1-184 BANB LICA FUNCTION FAIL............................................................... 662

SMD-011-PMA210

Page:24(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-185 BANB LICA BOARD FAIL ..................................................................... 662

FIG. 5.1-186 BSTB BADA ALARM CABLE OPEN ..................................................... 662

FIG. 5.1-187 BSTB BADA POWER FAIL.................................................................... 663

FIG. 5.1-188 BSTB BADA FUNCTION FAIL.............................................................. 663

FIG. 5.1-189 RISB RISA ALARM CABLE OPEN......................................................... 663

FIG. 5.1-190 RISB RISA POWER FAIL ............................. .......................................... 664

FIG. 5.1-191 RISB RISA FUNCTION FAIL................................................................. 664

FIG. 5.1-192 BOTB BOTA ALARM CABLE OPEN..................................................... 664

FIG. 5.1-193 BOTB BOTA POWER FAIL ................................................................... 665

FIG. 5.1-194 BOTB BOTA BOARD OPEN FAIL......................................................... 665

FIG. 5.1-195 BTGB GPS SINGLE FUNCTION FAIL .................................................. 665

FIG. 5.1-196 BTGB GPS DUAL FUNCTION FAIL ..................................................... 666

FIG. 5.1-197 BTGB GPS SINGLE POWER FAIL......................................................... 666

FIG. 5.1-198 BTGB GPS DUAL POWER FAIL ........................................................... 666

FIG. 5.1-199 BTGB GPS SINGLE BOARD OPEN FAIL .............................................. 667

FIG. 5.1-200 BTGB GPS DUAL BOARD OPEN FAIL ................................................. 667

FIG. 5.1-201 BTGB GPS CONTROL CABLE OPEN ................................................... 667

FIG. 5.1-202 BTGB GPS ALARM CABLE OPEN........................................................ 668

FIG. 5.1-203 DBPB DBPA FUNCTION FAIL.............................................................. 668

FIG. 5.1-204 DBPB DBPA BOARD OPEN FAIL.......................................................... 668

FIG. 5.1-205 RCCB RCP SINGLE FUNCTION FAIL................................................... 668

FIG. 5.1-206 RCCB RCP DUAL FUNCTION FAIL...................................................... 669

FIG. 5.1-207 RCCB RCP SINGLE BOARD OPEN FAIL............................................... 669

FIG. 5.1-208 RCCB RCP DUAL BOARD OPEN FAIL.................................................. 669

FIG. 5.1-209 RCCB BUDA FUNCTION FAIL ............................................................. 670

FIG. 5.1-210 RCCB BUDA BOARD OPEN FAIL ......................................................... 670

FIG. 5.1-211 RCCB PACA FUNCTION FAIL.............................................................. 670

FIG. 5.1-212 RCCB PACA BOARD OPEN FAIL.......................................................... 671

FIG. 5.1-213 DBPB/RCCB PRI SINGLE POWER FAIL................................................ 671

FIG. 5.1-214 DBPB/RCCB PRI DUAL POWER FAIL .................................................. 671

FIG. 5.1-215 DBPB/RCCB PRI SINGLE POWER OPEN FAIL..................................... 672

FIG. 5.1-216 DBPB/RCCB PRI DUAL POWER OPEN FAIL........................................ 672

FIG. 5.1-217 DBPB/RCCB ALARM CABLE OPEN...................................................... 672

FIG. 5.1-218 LPAB ALARM CABLE OPEN ................................................................ 673

FIG. 5.1-219 LPAB LPA COMBINER FAIL................................................................. 673

FIG. 5.1-220 LPAB LPA COMBINER FAN FAIL ........................................................ 673

FIG. 5.1-221 LPAB LPA BOARD OPEN FAIL ............................................................ 674

SMD-011-PMA210

Page:25(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-222 LPAB LPA BOARD FUNCTION FAIL.................................................... 674

FIG. 5.1-223 LPAB LPA DC/DC ALARM.................................................................... 674

FIG. 5.1-224 LPAB LPA VSWR ALARM....................................................................... 674

FIG. 5.1-225 LPAB LPA DISABLE ALARM................................................................ 675

FIG. 5.1-226 LPAB LPA OVER POWER WARNING ................................................... 675

FIG. 5.1-227 LPAB LPA OVER TEMPERATURE ALARM.......................................... 675

FIG. 5.1-228 LPAB LPA OVER POWER ALARM........................................................ 676

FIG. 5.1-229 HPAB HPA ALARM CABLE OPEN........................................................ 676

FIG. 5.1-230 HPAB HPA BOARD OPEN FAIL............................................................ 676

FIG. 5.1-231 HPAB HPA POWER FAIL...................................................................... 676

FIG. 5.1-232 HPAB HPA POWER SUPPLY ALARM................................................... 677

FIG. 5.1-233 HPAB HPA VSWR ALARM.................................................................... 677

FIG. 5.1-234 HPAB HPA DISABLE ALARM................................................................. 677

FIG. 5.1-235 HPAB HPA OVER TEMPERATURE ALARM......................................... 677

FIG. 5.1-236 HPAB HPA OVER POWER ALARM....................................................... 678

FIG. 5.1-237 CFEB LNA ALARM CABLE OPEN FAIL ............................................... 678

FIG. 5.1-238 CFEB LNA BOARD OPEN FAIL ............................................................ 678

FIG. 5.1-239 CFEB LNA FUNCTION FAIL ................................................................ 678

FIG. 5.1-240 OUTDOOR BTS ENV ALARM CABLE OPEN........................................ 679

FIG. 5.1-241 OUTDOOR BTS ENV RECTIFIER UNIT ALARM CABLE OPEN........... 679

FIG. 5.1-242 OUTDOOR BTS ENV COLD STARTER FAIL........................................ 679

FIG. 5.1-243 OUTDOOR BTS ENV RECTIFIER UNIT FAIL ...................................... 680

FIG. 5.1-244 OUTDOOR BTS ENV VOLTAGE HIGH ALARM ................................... 680

FIG. 5.1-245 OUTDOOR BTS ENV VOLTAGE LOW ALARM .................................... 680

FIG. 5.1-246 OUTDOOR BTS AC FAIL...................................................................... 680

FIG. 5.1-247 OUTDOOR BTS ENV BATTERY LOW VOLTAGE ALARM................... 681

FIG. 5.1-248 OUTDOOR BTS ENV FUSE/RELAY LOSS ALARM .............................. 681

FIG. 5.1-249 OUTDOOR BTS ENV DMC-14 FAIL..................................................... 681

FIG. 5.1-250 OUTDOOR BTS ENV POWER CUT ALARM ......................................... 682

FIG. 5.1-251 OUTDOOR BTS ENV TEMPERATURE HIGH ALARM.......................... 682

FIG. 5.1-252 OUTDOOR BTS ENV TEMPERATURE LOW ALARM ........................ 682

FIG. 5.1-253 OUTDOOR BTS ENV WATER HIGH ALARM........................................ 682

FIG. 5.1-254 OUTDOOR BTS ENV WATER LOW ALARM......................................... 683

FIG. 5.1-255 OUTDOOR BTS ENV FIRE ALARM ...................................................... 683

FIG. 5.1-256 OUTDOOR BTS ENV HUMIDITY HIGH ALARM................................... 683

FIG. 5.1-257 OUTDOOR BTS ENV ACU MODULE FAIL ........................................... 684

FIG. 5.1-258 OUTDOOR BTS ENV HEAT EXCHANGER POWER FAIL..................... 684

SMD-011-PMA210

Page:26(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-259 OUTDOOR BTS ENV HEAT EXCHANGER FAIL .................................. 684

FIG. 5.1-260 OUTDOOR BTS ENV LPA FAN FAIL ................................................... 684

FIG. 5.1-261 OUTDOOR BTS ENV AC EQUIPMENT HEATER FAIL ........................ 685

FIG. 5.1-262 OUTDOOR BTS ENV FRONT/REAR DOOR OPEN ALARM .................. 685

FIG. 5.1-263 OUTDOOR BTS ENV SIDE DOOR OPEN ALARM................................. 685

FIG. 5.1-264 OUTDOOR BTS ENV FAN FAIL ........................................................... 686

FIG. 5.1-265 OUTDOOR BTS ENV AC BATTERY HEATER FAIL............................. 686

FIG. 5.1-266 INDOOR BTS ENV TEMPERATURE HIGH ALARM.............................. 686

FIG. 5.1-267 INDOOR BTS ENV TEMPERATURE LOW ALARM............................... 686

FIG. 5.1-268 INDOOR BTS ENV FLOOD ALARM ...................................................... 687

FIG. 5.1-269 INDOOR BTS ENV DOOR #1 OPEN ALARM ........................................ 687

FIG. 5.1-270 INDOOR BTS ENV DOOR #2 OPEN ALARM ........................................ 687

FIG. 5.1-271 INDOOR BTS ENV FIRE ALARM .......................................................... 688

FIG. 5.1-272 INDOOR BTS ENV RECTIFIER #1 FAILS............................................. 688

FIG. 5.1-273 INDOOR BTS ENV RECTIFIER #2 FAIL............................................... 688

FIG. 5.1-274 INDOOR BTS ENV AIRCON #1 FAIL.................................................... 688

FIG. 5.1-275 INDOOR BTS ENV AIRCON #2 FAIL.................................................... 689

FIG. 5.1-276 INDOOR BTS ENV WATER LEAKAGE ALARM.................................... 689

FIG. 5.1-277 BTS RACK FAN FAIL ............................................................................. 689

FIG. 5.1-278 KEEP-ALIVE FAULT BETWEEN CNP AND NCP................................ 690

FIG. 5.1-279 KEEP-ALIVE FAULT BETWEEN PNP AND NCP ................................ 690

FIG. 5.1-280 KEEP-ALIVE FAULT BETWEEN PNP AND PCP................................. 690

FIG. 5.1-281 KEEP-ALIVE FAULT BETWEEN PCP AND CCP................................. 691

FIG. 5.1-282 KEEP-ALIVE FAULT BETWEEN PCP AND PNP................................. 691

FIG. 5.1-283 KEEP-ALIVE FAULT BETWEEN CCP AND NCP ................................ 691

FIG. 5.1-284 KEEP-ALIVE FAULT BETWEEN CCP AND PCP................................. 692

FIG. 5.1-285 KEEP-ALIVE FAULT BETWEEN CCP AND BSP................................. 692

FIG. 5.1-286 KEEP-ALIVE FAULT BETWEEN CCP AND SCP................................. 692

FIG. 5.1-287 KEEP-ALIVE FAULT BETWEEN CCP AND SMP................................ 693

FIG. 5.1-288 KEEP-ALIVE FAULT BETWEEN CCP AND VMP................................ 693

FIG. 5.1-289 KEEP-ALIVE FAULT BETWEEN NCP AND CNP................................ 693

FIG. 5.1-290 KEEP-ALIVE FAULT BETWEEN NCP AND CCP ................................ 694

FIG. 5.1-291 KEEP-ALIVE FAULT BETWEEN NCP AND PNP ................................ 694

FIG. 5.1-292 KEEP-ALIVE FAULT BETWEEN NCP AND CRP ................................ 694

FIG. 5.1-293 KEEP-ALIVE FAULT BETWEEN SCP AND CCP................................. 695

FIG. 5.1-294 KEEP-ALIVE FAULT BETWEEN SCP AND STIA................................ 695

FIG. 5.1-295 KEEP-ALIVE FAULT BETWEEN BSP AND CCP................................. 695

SMD-011-PMA210

Page:27(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-296 KEEP-ALIVE FAULT BETWEEN BSP AND RCP................................. 696

FIG. 5.1-297 KEEP-ALIVE FAULT BETWEEN BSP AND BPP................................. 696

FIG. 5.1-298 KEEP-ALIVE FAULT BETWEEN RCP AND DBPA.............................. 696

FIG. 5.1-299 VOCODER CLOCK FAULT.................................................................... 697

FIG. 5.1-300 QCELP0 ALGORITHM FAULT.............................................................. 697

FIG. 5.1-301 QCELP1 ALGORITHM FAULT.............................................................. 697

FIG. 5.1-302 QCELP2 ALGORITHM FAULT.............................................................. 698

FIG. 5.1-303 QCELP3 ALGORITHM FAULT.............................................................. 698

FIG. 5.1-304 VCPA LOOP-BACK TEST FAULT ....................................................... 698

FIG. 5.1-305 VOCODER DSP ROM TEST FAULT ..................................................... 699

FIG. 5.1-306 VOCODER DSP RAM TEST FAULT ..................................................... 699

FIG. 5.1-307 VOCODER DSP ROM/RAM TEST FAULT ............................................ 699

FIG. 5.1-308 VOCODER DSP ALU TEST FAULT...................................................... 700

FIG. 5.1-309 VOCODER DSP ROM/ALU TEST FAULT............................................. 700

FIG. 5.1-310 VOCODER DSP RAM/ALU TEST FAULT............................................. 700

FIG. 5.1-311 VOCODER DSP ROM/RAM/ALU TEST FAULT .................................... 701

FIG. 5.1-312 VLIA E1/T1 TRUNK TIME-SLOT TEST FAULT................................. 701

FIG. 5.1-313 SCI FAULT............................................................................................ 701

FIG. 5.1-314 BASE ID FAULT ................................................................................... 702

FIG. 5.1-315 BTS ID FAULT...................................................................................... 702

FIG. 5.1-316 SECTOR ID FAULT............................................................................... 702

FIG. 5.1-317 NEIGHBOR LIST FAULT ...................................................................... 703

FIG. 5.1-318 MSC OVERLOAD FAULT...................................................................... 703

FIG. 5.1-319 CCP OVERLOAD FAULT ...................................................................... 703

FIG. 5.1-320 BSP OVERLOAD FAULT ...................................................................... 704

FIG. 5.1-321 GET TASK FUNCTION FAULT............................................................ 704

FIG. 5.1-322 FREE TASK FUNCTION FAULT .......................................................... 704

FIG. 5.1-323 GET BUFFER FUNCTION FAULT........................................................ 705

FIG. 5.1-324 AUTHENTICATION FAULT ................................................................. 705

FIG. 5.1-325 STM SYSTEM TIME FAULT ................................................................ 705

FIG. 5.1-326 CDM TX PARITY FAULT...................................................................... 706

FIG. 5.1-327 CDM RX PARITY FAULT...................................................................... 706

FIG. 5.1-328 CDM TX OVER-FLOW FAULT............................................................. 706

FIG. 5.1-329 CDM TX M2R DATA ERROR................................................................. 707

FIG. 5.1-330 CDM TX R2B DATA ERROR ................................................................. 707

FIG. 5.1-331 CDM RX B2R DATA ERROR ................................................................. 707

FIG. 5.1-332 OVERHEAD CHANNEL CONFIG NO RECEIVED FAULT ..................... 707

SMD-011-PMA210

Page:28(877)

Issue:1.

STAREX-IS BSM Manual

0

FIG. 5.1-333 OVERHEAD CHANNEL CONFIG INVALID FAULT .............................. 708

FIG. 5.1-334 DBPA INTERNAL EVEN CLOCK FAULT ............................................. 708

FIG. 5.1-335 DBPA EXTERNAL SYSTEM CLOCK FAULT........................................ 708

FIG. 5.1-336 DBPA TOD NOT ACTIVE FAULT ........................................................ 709

FIG. 5.1-337 DBPA CMC NO FREE QUEUE FAULT.................................................. 709

FIG. 5.1-338 DBPA INTERNAL SYNC CLOCK FAULT................................................ 709

FIG. 5.1-339 DBPA CORE NO FREE QUEUE FAULT................................................ 710

FIG. 5.1-340 DBPA QUEUE PUT FAULT.................................................................. 710

FIG. 5.1-341 DBPA QUEUE GET FAULT.................................................................. 710

FIG. 5.1-342 DBPA S/W WATCHDOG TIMEOUT FAULT ......................................... 710

FIG. 5.1-343 DBPA FATAL FAULT........................................................................... 711

FIG. 5.1-344 DBPA BAD CHANNEL MODEM FAULT ............................................... 711

FIG. 5.1-345 DBPA EXTERNAL TOD FAULT ........................................................... 711

FIG. 5.1-346 DBPA INTERNAL OS CLOCK FAULT .................................................. 712

FIG. 5.1-347 DBPA BIT FAIL..................................................................................... 712

FIG. 5.1-348 DBPA TC NO SVC FREE QUEUE FAIL ................................................ 712

FIG. 5.1-349 DBPA TC NO NORMAL FREE QUEUE FAIL ........................................ 712

FIG. 5.1-350 DBPA TC TX FWHENO FULL FAIL ..................................................... 713

FIG. 5.1-351 DBPA ACH NO FREE QUEUE FAIL...................................................... 713

FIG. 5.1-352 DBPA PC NO ENCODER FREE QUEUE FAIL....................................... 713

FIG. 5.1-353 DBPA PC NO PAGE FREE QUEUE FAIL .............................................. 714

FIG. 5.1-354 DBPA PC NO QUICK PAGE FREE QUEUE FAIL .................................. 714

FIG. 5.1-355 DBPA PC NO REPLY FREE QUEUE FAIL............................................. 714

FIG. 5.1-356 DBPA PC WRITE FRAME FAIL............................................................. 715

FIG. 5.1-357 DBPA PC NO GENERAL PAGE FREE QUEUE FAIL............................. 715

FIG. 5.1-358 BUDA CHIPX16 FAULT........................................................................ 715

FIG. 5.1-359 BUDA FORWARD SYNC FAULT........................................................... 716

FIG. 5.1-360 BUDA TX SATURATION FAULT ......................................................... 716

FIG. 5.1-361 BUDA FRAME ERROR FAULT.............................................................. 716

FIG. 5.1-362 BOTA TOD ERROR FAULT .................................................................. 717

FIG. 5.1-363 BOTA TOD NOT ACTIVE FAULT........................................................ 717

FIG. 5.2-1 CNP PROCESSOR STATUS CHANGE REPORT ....................................... 718

FIG. 5.2-2 PNP PROCESSOR STATUS CHANGE REPORT........................................ 718

FIG. 5.2-3 PCP PROCESSOR STATUS CHANGE REPORT........................................ 719

FIG. 5.2-4 PMP PROCESSOR STATUS CHANGE REPORT ....................................... 719

FIG. 5.2-5 CCP PROCESSOR STATUS CHANGE REPORT........................................ 720

FIG. 5.2-6 NCP PROCESSOR STATUS CHANGE REPORT ....................................... 720

SMD-011-PMA210

Page:29(877)

Issue:1.