LG Electronics 32LT777H, 42LT777H, 47LT777H, 37LT777H User Manual

32LT777H
37LT777H
42LT777H
47LT777H
Lodging Guest Interactive Pro:Centric® TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EZ-Manager Wizard pages 11 – 18
Custom Master TV Setup pages 31 – 34
FTG Mode of Operation pages 45 – 46
© Copyright 2013 LG Electronics U.S.A., Inc.
P/N: 206-4234 (Rev B)
For Customer Support/Service, please call:
1-888-865-3026
The latest product information and documentation is available online at:
www.LGsolutions.com
MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:
Model No._________________ Serial No._______________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER­SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip­ment does cause harmful interference to radio or television reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
2
© Copyright 2013 LG Electronics U.S.A., Inc.
206-4234
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accor­dance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination in order to avoid injury from tip-over.
PORTABLE CART WARNING
13.
Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Never touch this apparatus or antenna during a thunder or
lightning storm.
15. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
16. Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.
17. Power Cord Caution: It is recommended that appliances be placed
upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the TV specifications to be certain.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not use a damaged or loose power cord. Be sure to grasp
the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
18. Overloading Do not connect too many appliances to the same AC power
outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in re or electric shock.
19. Outdoor Use/Wet Location Warning: To reduce the risk of re or electrical shock, do not expose this product to rain, moisture or other liquids.
Do not touch the TV with wet hands. Do not install this product
near ammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place
objects lled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).
20. Grounding
Ensure that you connect the earth ground wire to prevent
possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualied electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.
21. Disconnect Device
The mains plug is the disconnecting device. The plug must
remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit by SWITCH.
(Continued on next page)
206-4234
3
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the
product, follow the precautions below.
An outdoor antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to NEC, ANSI/NFPA 70
Ground Clamp
Electric Service
Equipment
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
23. Cleaning When cleaning, unplug the power cord and wipe gently with
a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
24. Transporting Product Make sure the TV is turned Off and unplugged and that all
cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.
25. Ventilation Install the TV where there is proper ventilation. Do not install
in a conned space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.
26. Do not touch the ventilation openings, as they may become
hot while the TV is operating.
27. If you smell smoke or other odors coming from the TV or
hear strange sounds, unplug the power cord, and contact an authorized service center.
28. Do not press against the front panel of the TV with your
hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.
29. Keep the product away from direct sunlight.
30. Dot Defect
The LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see ne dots on the screen while you are viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.
31. Generated Sound
“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.
32. For LCD TV
If the TV feels cold to the touch, there may be a small “icker” when it is turned On. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your nger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
4
206-4234
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 3 – 4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . . .6 – 8
Setup Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pass-through Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Management in FTG Mode . . . . . . . . . . . . . . . . . . . . 8
Pro:Centric Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 – 10
Pro:Centric TV Interactive Menu Features . . . . . . . . . . . . . . . 9
Pro:Centric Interactive Menu Navigation . . . . . . . . . . . . . . . . 9
Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EZ-Manager Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 – 18
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Initiate Configuration or Exit the EZ-Manager Wizard . . . . . 12
TV Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Zone and Room Number Assignments . . . . . . . . . . . . . . . . . 14
Configure Pro:Centric Settings . . . . . . . . . . . . . . . . . . . . . . . 15
USB Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LG Smart Install Utility. . . . . . . . . . . . . . . . . . . . . . . . . . 19 – 20
Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 – 30
Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Installer Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Exiting the Installer Menu and Activating Settings . . . . . . . . 22
Custom Master TV Setup. . . . . . . . . . . . . . . . . . . . . . . . .31 – 34
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cloning Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Clonable TV Setup Menu Features . . . . . . . . . . . . . . . . . . . 31
Custom Master TV Setup Procedure . . . . . . . . . . . . . . . . . . 32
Channel Icons / Custom Text Labels (2-5-4 + MENU Mode). . 35
Cloning Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
USB Cloning Procedures. . . . . . . . . . . . . . . . . . . . . . . . . 37
Learning / Teaching a Master TV Setup using
a USB Memory Device / .tlx File. . . . . . . . . . . . . . . . . . . . . . 37
Learning / Teaching a Master TV Setup using
a USB Memory Device / .tll File . . . . . . . . . . . . . . . . . . . . . . 39
Clone Programmer Cloning Procedures . . . . . . . . . . . .41
Learning / Teaching a Master TV Setup using
a TLL-1100A Clone Programmer . . . . . . . . . . . . . . . . . . . . . 41
Learning / Teaching a Master TV Setup using
an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . . . . . . 43
FTG Mode of Operation Overview . . . . . . . . . . . . . . . . .45
FTG Mode via CPU or EBL . . . . . . . . . . . . . . . . . . . . . . . . . 45
Determining the TV Operating Mode . . . . . . . . . . . . . . . . . . 46
40
44
46
FTG Mode via CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Creating an FTG Configuration File using the
FTG File Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Teaching FTG Configuration to a TV . . . . . . . . . . . . . . . . . . 49
Learning FTG Configuration from a TV . . . . . . . . . . . . . . . . 50
Optional Manual Configuration / TV Setup . . . . . . . . . . . . . . 51
FTG File Manager Utilities Overview. . . . . . . . . . . . . . . .52 – 55
FTG File Manager Main Screen . . . . . . . . . . . . . . . . . . . . . . 52
FTG Channel Map Configuration Utility . . . . . . . . . . . . . . . . 53
FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FTG Installer Menu Configuration Utility. . . . . . . . . . . . . . . . 55
IP Environment Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 – 63
Accessing the IP Environment Menu . . . . . . . . . . . . . . . . . . 56
Configuring the Network Connection . . . . . . . . . . . . . . . . . . 56
Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
IP Stream Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Wake On LAN Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Media Share Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Pre-loaded Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
References
Remote Jack Pack / TV Connections & Setup. . . . . . . . . . . . . 64
Upgrading TV/PTC Software using a USB Memory Device . . . 65 Downloading a Splash Screen using a USB Memory Device . . 66
Power Consumption Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 67
TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
FTG Mode via EBL (Local Configuration) . . . . . . . . . . . . . . . . 70
RJP Model List & Input Auto-sensing Hierarchy . . . . . . . . . . . 71
Restoring Factory Defaults on the TV(s) . . . . . . . . . . . . . . . . . 72
Using the TV Zoning Feature . . . . . . . . . . . . . . . . . . . . . . .73 – 75
Wi-Fi Screen Share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
LT777H Rear and Side Jack Panels . . . . . . . . . . . . . . . . . . . . 77
External Stereo Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . 78
Installer Remote Control Typical Key Functions . . . . . . . . . . . 79
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Commercial Mode Check / FTG Operation Troubleshooting . 81
Clone Programmer Troubleshooting. . . . . . . . . . . . . . . . . . . 82
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Document Revision History / Open Source Software Notice . . . 84
Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
51
– 82
Notes
Installer Menu content is intended for use primarily by qualied TV electronics technicians.
Refer to the applicable Quick Reference Guide for additional information on TV installation, specications, maintenance, and safety instructions.
Design and specications subject to change without prior notice. This document provides examples of typical TV displays. Your displays may vary
from those shown in this document.
206-4234
5
Commercial Mode Overview
This document describes how to set up LT777H Pro:Centric ® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider).
These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the EBL module can be configured either for Pass-through Mode (default) or FTG Mode. When neither the CPU nor EBL is in FTG Mode, these TV models also allow external control via the TV’s MPI port.
Setup Checklist
Note: This document provides information specific to Commercial Mode operation. Refer to the Quick
Reference Guide for information on TV installation and hardware and cable connections.
Installation
__ Unpack TV and all accessories. __ Install batteries in the Installer Remote. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable
connections before installing on VESA mount or stand, as appropriate.
Hardware Connections
__ Install any additional hardware as
appropriate to your institution, LAN, etc.
Cable Connections
__ Make all rear jack panel and MPI card slot
connections, as appropriate.
Commercial Mode Setup
__ Complete appropriate procedures as described
in this document for Commercial Mode operation.
Pass-through Mode
This mode allows you to configure individual TVs for Pro:Centric or FTG Mode via CPU operation and/ or create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This mode also allows external control via the GAME CONTROL/MPI port on the TV rear jack panel.
There are two methods for configuring individual TVs that are currently in Pass-through Mode: either using the EZ-Manager Wizard or the Custom Master TV Setup procedure as described in this document.
EZ-Manager Wizard
The EZ-Manager Wizard provides automated or manual options for conguring essential items for Pro:Centric operation and also provides an option for using a USB memory device to congure the TV. Use the Installer Remote to make selections and complete each step. See “EZ-Manager Wizard” on pages 11 to 18 for detailed information.
Custom Master TV Setup
The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for cloning purposes. Use the Installer Remote to congure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). See “Custom Master TV Setup” on pages 31 to 34 for detailed information.
6
206-4234
Installer Menu
To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 21 to 30 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
Commercial Mode Overview (Cont.)
xxLT777H PTC INSTALLER MENU
CPU-CTV
000 INSTALLER SEQ 000
TV Setup Menus
On-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user.
Cloning
Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV. Both TVs must be in Pass-through Mode and both TVs must be identical models. The Master TV’s clonable setup menu features should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. Refer to pages 36 to 44 for detailed information on cloning requirements and procedures.
External MPI Control
To control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/ MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as Reference section, “b-LAN Setup & Overview,” for further information.
Note: These TV models are not equipped with MPI card slots.
UPN 000-000-000-000 ASIC D279
PTC V1.01.026 CPU V3.45.00
Typical Installer Menu
PICTURE
LOCK
AUDIO
OPTION
TV Setup Menus
CHANNEL
INPUT
TIME
SmartShare
206-4234
7
Commercial Mode Overview (Cont.)
FTG Mode
This mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be used is vital in determining the owner.
As indicated above, FTG mode operation in the LT777H models can be provided either by the TV CPU or the EBL. These are two separate and distinct FTG Modes of operation, each with its own unique advantages and requirements as described later in this document. When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.
Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, conguration can begin. Conguration of either requires a PC application—the LG FTG File Manager for the TV CPU or the LG FTG Device Conguration Application for the EBL. Each application provides utilities that enable you to create/edit an FTG Channel Map and congure Installer Menu settings. See “FTG Mode of Operation Overview” on pages 45 to 46 for further information on FTG Mode operation and conguration.
Remote Management in FTG Mode
When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric Server Admin Client User Guide for further information.
When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See Reference section, “b-LAN Setup & Overview,” for further information.
8
206-4234
Pro:Centric Operation
Pro:Centric TV Interactive Menu Features
When running the Pro:Centric application, the interactive Pro:Centric TV enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hotel and surrounding amenities via custom billboards and points-of-interest maps.
Pro:Centric application features include:
• Portal and information screens/pages (including a “Welcome” page) that include branding logos.
• An optional customized user interface (custom “skins”).
• Billboards and points-of-interest maps that can be customized to focus on hotel amenities, local attractions and businesses, restaurants, news, events, etc.
• An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.
• An interactive channel guide that provides a channel list with channel icons. An electronic program guide (EPG) is an optional feature that displays up to three days of programming information viewable by channel and time.
• Video spooling that enables the hotel to deliver a video le to guest TVs for promotion and information purposes.
The Pro:Centric server Admin Client web editor/content wizard is provided for customer conguration of portal messages and billboards/maps.
Note: Customized content is typically dened by the service integrator and/or hotel administrators. LG does not provide hotel-specic content.
Pro:Centric Interactive Menu Navigation
Use the Pro:Centric TV remote control to operate both interactive menus and regular TV features. Press
PORTAL on the remote to access the interactive menus.
Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The
following are default interactive menus.
Channel Guide
Shows available TV networks and logical channels. When available, EPG data provides additional channel and program information.
Information
Typically displays information on hotel amenities, for example, restaurants, in-room dining, business centers, facilities, etc., as well as information on local weather and attractions.
Help
Provides help for navigating the interactive menus.
Watch TV
Removes the interactive menu from the screen and returns to the previously tuned TV channel.
206-4234
9
Pro:Centric Operation (Cont.)
Pro:Centric Setup
Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be specied on the TVs.
On the TVs, the Pro:Centric server settings must be congured appropriately to enable Pro:Centric remote management/administration facilities, while the Pro:Centric Application Mode must be set appropriately to enable the Pro:Centric application.
• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading the FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU.
• Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes, comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric application settings are managed via the Pro:Centric Admin Client.
The Pro:Centric server settings can be congured using one of the following methods:
• When the TV is in a factory default state, the EZ-Manager Wizard provides automated or manual options for conguring the Pro:Centric server settings.
The EZ-Manager Wizard also provides a USB Conguration option that enables you to congure a TV for FTG Mode via CPU using an FTG Conguration (.tlx) le stored on a USB memory device. The FTG Conguration le incorporates FTG Installer Menu settings, which includes Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL.
Refer to “EZ-Manager Wizard” on pages 11 to 18 for further information on the EZ-Manager Wizard options.
• If the TV is in Pass-through Mode, either:
− Set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL to the appropriate values. Refer to “Installer Menu” information on pages 21 to 30 for further information. Also, as necessary, refer to “Custom Master TV Setup” information on pages 31 to 34 and/or cloning information on pages 36 to 44.
− Congure the appropriate Pro:Centric server settings in the IP Environment / Pro:Centric Menu. You must use this option, in particular, if you wish to congure IP settings for the Pro:Centric server. See “Accessing the IP Environment Menu” on page 56 and “Pro:Centric Setup” on page 60 for further information.
Note: When the TV is in either Pass-through Mode or FTG Mode via CPU, you can also leave Installer Menu item 119 DATA CHANNEL set to its default value (255) to enable the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value. See item 119 description on page 30 for additional information.
• If the TV is in FTG Mode (via CPU or EBL), use the appropriate software to update the Data Channel and Pro:Centric Installer Menu items (along with their afliated elds) and then transfer the FTG Installer Menu settings to the TV in accordance with the FTG Mode of conguration. Refer to “FTG Mode of Operation Overview” on pages 45 to 46 for further information on FTG Mode operation and conguration. Also—for FTG Mode via CPU only—see note above regarding the option to use the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value.
10
206-4234
EZ-Manager Wizard
The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual) of configuring the essential Installer Menu items for Pro:Centric TV operation. The wizard will appear on the screen each time the TV is turned ON, until one of its configuration methods has been completed or the wizard is exited. Use the Installer Remote to make selections and complete each wizard step.
While the EZ-Manager Wizard is intended primarily for Pro:Centric-related conguration, the wizard also offers Zoning as well as USB conguration options.
• LT777H TVs support the TV Zoning feature, which enables location-specic settings (see Reference section, “Using the TV Zoning Feature,” for further information). The EZ-Manager Wizard enables you to set the TV Zone # in the TV as part of the conguration process.
• The EZ-Manager Wizard also enables you to redirect to the TV’s standard USB Download Menu as part of the conguration process, if desired, to perform USB conguration functions, including FTG Mode via CPU conguration, cloning, and software upgrades.
• You can connect a USB memory device to the TV at any time while the wizard is in progress (either at the Welcome level or beyond) to use the LG Smart Install utility to perform USB conguration functions. Any le(s) you wish to use for conguration purposes must be stored in a folder named “LGSMARTINSTALL” in the root directory of the USB memory device. See “LG Smart Install Utility” on pages 19 to 20 for further information.
Caution: Do NOT unplug the TV power cord or remove the antenna cable or, if applicable, the LAN cable during the conguration process, as doing so will interrupt the current step and may corrupt the conguration data.
Before You Begin
• If you plan to create a Master TV Setup using the procedure described on pages 31 to 34, be sure to exit the EZ-Manager Wizard in order to avoid setting modes that may restrict the custom setup procedure. See also “Initiate Conguration or Exit the EZ-Manager Wizard” on the following page.
• If it has been completed or exited and therefore does not display, the EZ-Manager Wizard can be reactivated; however, this requires that you perform an “IN-STOP” to restore factory defaults on the TV(s). Refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
• Each wizard step is allotted a time frame after which the wizard proceeds without user interaction. If the Pro:Centric server is congured on the system and if no location-specic settings are required in the TV, for example, for TV Zone, Label, and/or Room Number settings, you can simply turn ON the TV, and once initiated, the wizard will proceed through each of the conguration steps with no further user interaction.
• If any of the conguration steps fails, you will see a “Diagnostics” screen with an indication of the failure. You will then have the opportunity to reinitiate the conguration process from the previous screen or exit the EZ-Manager Wizard.
• If you wish to enable media sharing (i.e., Smart Share, Wi-Fi Screen Share, and DMR) on the TV with­out using a .tlx le for conguration purposes, you will need to create a custom Master TV Setup and use the IP Environment Menu to specify the settings. Custom Master TV Setup is described on pages 31 to 34. Refer to “IP Environment Setup” on pages 56 to 63 for information on the IP Environment Menu.
206-4234
11
EZ-Manager Wizard (Cont.)
Initiate Conguration or Exit the EZ-Manager Wizard
The Welcome screen provides a brief introduction to the EZ-Manager wizard.
EZ-Manager Wizard
Welcome to LG’s EZ-Manager Wizard
• Use this setup wizard to congure the TV for Pro:Centric and/or Free­To-Guest (FTG) operation.
Select ‘Next’ to continue.
• If a Pro:Centric Server will not be installed and/or you do not wish to use the wizard to congure this TV for FTG Mode, you may exit the wizard.
Select ‘No Pro:Centric’ to disable the Pro:Centric feature of this TV, or select ‘Exit’ to quit.
This setup wizard will start automatically in 10 seconds.
No Pro:Centric
Exit
Next
Note: If there is no user action in this screen within 10 seconds, the wizard will proceed to the rst conguration step. Once the wizard has proceeded, it is not possible to return to the Welcome screen; however, if you simply wish to exit the wizard, you can do so by selecting the “Exit” option from the subsequent screen(s).
Note: As indicated on the previous page, you may use the LG Smart Install feature to congure the TV using a USB memory device at any time while the EZ-Manager Wizard is in progress. However, if you want to use the TV Zoning feature for location-specic conguration purposes, proceed to the EZ-Manager’s Zone, Label, and Room Number screen and assign a TV Zone # for this TV before inserting your USB device. See “TV Conguration Options” on the following page for further information.
From the Welcome screen, you have the following options:
• To proceed with the EZ-Manager Wizard, use the arrow keys on the Installer Remote to select/
highlight Next and press OK. Then, continue to the “TV Conguration Options” section on the following page.
• To exit the wizard, but retain the use of the Pro:Centric feature of this TV (i.e., Installer Menu item 119 DATA CHANNEL set to 255) in the future, use the arrow keys on the Installer Remote to select/highlight Exit and press OK. In the conrmation pop-up window, select OK, and then press OK once more on the Installer Remote.
• If you do not intend to install a Pro:Centric server on this system and you do not wish to use the wizard’s Zoning or USB conguration options, exit the wizard as follows: Use the arrow keys on the Installer Remote to select/highlight the No Pro:Centric option. This will disable the Pro:Centric feature of this TV (i.e., Installer Menu item 119 DATA CHANNEL will be set to 0) and exit the wizard. In the conrmation pop-up window, select OK, and then press OK once more on the Installer Remote.
12
206-4234
EZ-Manager Wizard (Cont.)
TV Conguration Options
From the TV Conguration Options screen, you can choose how to proceed with the conguration of this TV (assuming you do not opt to exit the wizard—which you may also do at any time).
Note: If you intend to use the Zoning feature on the TV for location-specic conguration purposes, assign the TV Zone # in the TV BEFORE you continue with additional conguration.
Z
EZ-Manager Wizard
4
3
2
1
TV Configuration Options
• To congure the TV for Pro:Centric operation, select ‘Next’.
• To set the optional Zoning feature, select ‘Zone & Room Number’.
• To access the TV’s USB Download Menu, select ‘USB Conguration’.
This setup wizard will continue automatically in 60 seconds.
Exit
USB Configuration
Zone & Room Number
Next
Note: If there is no user action in this screen within one minute, the wizard will automatically continue to the next conguration step.
Use the Left/Right arrow keys on the Installer Remote to navigate between options on this screen. Each time you select/highlight one of the following options, the screen text and elds will change in accordance with your selection.
• To continue with Pro:Centric conguration, select Next (default) and press OK on the Installer Remote. Refer to “Congure Pro:Centric Settings” on pages 15 to 17 for additional information.
• To set the Zoning feature on this TV, select Zone & Room Number. See “Zone and Room Number Assignments” on the following page for further information.
• The “USB Conguration” option from this screen allows you to access the TV’s USB Download Menu. See “USB Conguration” on pages 17 to 18 for further information.
Note: If you have already inserted a USB memory device with the intent to use the LG Smart Install utility and the Integrated USB Downloading screen is on display, you may still set the Zoning feature on this TV by selecting Previous to return to the EZ-Manager/TV Conguration Options screen. Set the Zoning feature as required, and then select USB Conguration and press OK on the Installer Remote to return to the Integrated USB Downloading screen.
Note: If you choose to exit the EZ-Manager Wizard from this point on, you will have the option to save any settings made by selecting Save and Exit in the exit conrmation pop-up window. Or, you can exit the wizard without saving any settings by simply selecting OK in the conrmation pop-up window.
206-4234
13
EZ-Manager Wizard (Cont.)EZ-Manager Wizard (Cont.)
Zone and Room Number Assignments
You may complete one or more of the elds in the Zone, Label, and Room Number screen or leave them blank, as desired; however, in order to use the Zoning feature on this TV, you MUST set the TV Zone # as described below. See Reference section, “Using the TV Zoning Feature,” for further information on Zone designations. Note that the Zoning feature is only applicable for TVs that will be congured for FTG Mode via CPU (using an FTG Conguration [.tlx] le) or for TVs that will be congured via “Teaching” (cloning) using a USB memory device / .tlx le.
Z
EZ-Manager Wizard
4
3
2
1
If creating Zones for Installer Menu settings and/or Channel Mapping, select the appropriate Zone # (0-8) based on the Zone in which this TV is installed. (See Commercial Mode Setup Guide for more information.)
• Select a Label and/or use the alphanumeric keypad on the remote to input the Room Number.
• When done, select ‘Next’ to continue.
Zone
0
Exit
Zone, Label, and Room Number
-----
USB Configuration
Room NumberLabel
Zone & Room Number
Q.MENU
INPUT
2
1
3
TV
DVD
MARK
@
.,;
abc def
1 2 3
4
5 6
ghi jkl mno
4 5 6
pqrs tuv wxyz
7 809
7
CHAR/
NUM
FLASHBK
8
9
CHAR/NUM
CC
P A
TIMER
G
CHVOL
E
DELETE
DEL
MUTE
0
PORTAL
INFO
GUIDE
Next
1. Complete the appropriate eld(s) as described below. Use the Left/Right arrow keys on the
Installer Remote to navigate between each of the elds.
• Zone: Enables you to set a TV Zone # so that the TV can be congured with Installer Menu and/or TV Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or TV Setup Menu settings may be provided in a .tlx le to be used either for Teaching (cloning) or FTG Mode via CPU conguration. If the TV is being congured for FTG Mode via CPU, the TV Zone # setting also allows the TV to omit channels that have been restricted in the FTG Channel Map. To set a TV Zone, navigate to the Zone eld at the left of the screen, and use the Up/Down arrow keys to specify a TV Zone # (1–8).
• Label: Allows you to select a North, South, East, or West text label for this TV. In the Label eld, use the Up/Down arrow keys to select the applicable label.
• Room Number: Allows you to specify the number of the room in which the TV is located. In the Room Number eld, you can use the number keys on the Installer Remote to direct enter a room number. Use the Dash key on the Installer Remote as necessary to toggle between number and letter characters in the Room Number eld. Also, you can use the Flashback key on the Installer Remote to delete characters in this eld.
2. When you are ready to continue, select the appropriate option, as follows:
• To proceed to the next EZ-Manager screen, use the arrow keys to select Next, and then press OK on the Installer Remote. Continue to the “Congure Pro:Centric Settings” section on the following page.
• If you wish to use a USB memory device in conjunction with the TV’s standard USB Down­load Menu to complete the conguration, continue to “USB Conguration” on pages 17 to 18.
• If you wish to use a USB memory device in conjunction with the LG Smart Install utility to complete the conguration, see “LG Smart Install Utility” on pages 19 to 20.
14
206-4234
Congure Pro:Centric Settings
Once you select “Next” from the TV Conguration Options screen, the Searching for Pro:Centric Server screen is displayed (see example at right), and you have the following options:
• You can allow the EZ-Manager Wizard to proceed with a series of automated steps to congure the TV for Pro:Centric operation and then to look for the Pro:Centric application and maintenance (E-Z Installation) les to download. In this case, the wizard uses a search algorithm to determine the Data Channel and the Pro:Centric Application Mode to set in the TV.
Continue with the “Automated Pro:Centric Conguration” sub­section below.
• If you already know the settings (i.e., Data Channel and Pro:Centric Application Mode) that need to be congured in order for the TV to connect to the Pro:Centric server and/or if the Pro:Centric server is not yet installed, you may expedite the setup process by entering this data manually.
Continue with the “Manual Pro:Centric Conguration” subsection on the following page.
EZ-Manager Wizard (Cont.)
Z
EZ-Manager Wizard
4
3
1
2
Note: You can select the “Back” button, where available, to check previous settings, as necessary.
Searching for Pro:Centric Server...
It may take 1 min 32 second(s).
This step automatically searches for the Pro:Centric server.
If there is no Pro:Centric Server installed, you do not need to continue with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.
Status : Tuning channel 49
TV is now searching all of the channels for the data channel...
Back
Exit
Manual Pro:Centric
Automated Pro:Centric Conguration
Note: If the server is not yet congured on the system, use the
manual conguration option to congure the Pro:Centric operation.
Once the RF channel used by the Pro:Centric server as its data channel is found (the Pro:Centric Server Was Found screen will be displayed—see example at right) and the Pro:Centric Application Mode is determined, the wizard will advance to the Processing the Pro:Centric Conguration screen, which shows the progress of the data downloads. Note that some steps may require a few minutes.
If the process is successful, no further user interaction is required, though, in some instances, where the option (for example “Next”) is available, you may manually move forward to subsequent steps within the wizard to speed up the process.
Note: If, after completing the search, the TV is unable to nd a Pro:Centric server’s RF channel (while the Searching for Pro:Centric Server screen is on display), the wizard will stop and show a Diagnostics screen that enables you to manually return to the previous screen (to reinitiate the conguration) or exit the wizard.
When the Pro:Centric Conguration is complete, an EZ-Manager Conguration Complete screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.
Note: With the EZ-Manager Conguration Complete screen on display, you can also manually turn off or reboot the TV. If desired, select Turn Off or Reboot, respectively, and then press OK on the Installer Remote.
Z
EZ-Manager Wizard
1
EZ-Manager Wizard
1
EZ-Manager Wizard
1
4
3
2
Pro:Centric Server was found...
It may take 2 second(s).
The Pro:Centric data channel was found!! (Data Channel: 75, Mode: GEM) The Download window will open in 2 second(s). You may wait or select ‘Next’. Otherwise, if you select ‘Exit’, the Pro:Centric server settings can be retained and used during the next download by selecting ‘Save & Exit’ in the Exit window.
Status : Tuning channel 75
The Pro:Centric data channel is found!! (Data Channel: 75, Mode: GEM)
Back
4
2
3
Processing the Pro:Centric Configuration...
Downloading the maintenance files takes several minutes.
Application files
Maintenance files
Updating Configuration File
Warning - Do not remove AC power or the signal cables during these steps
3
2
4
Exit
Please wait...
Retrieving files from data channel 75
EZ-Manager Configuration Complete
The TV will turn off in 3 second(s).
Installed Components
Pro:Centric Application Maintenance Files
Reboot
GEM application downloaded
Next
GEM app downloaded
In progress...
LT777H_Config.tlx
Turn Off
20%
206-4234
15
EZ-Manager Wizard (Cont.)
Manual Pro:Centric Conguration
1. With the Searching for Pro:Centric Server screen on display,
use the arrow keys on the Installer Remote to select/highlight the Manual Pro:Centric option at the bottom right of the screen, and press OK.
In the Pro:Centric Manual Conguration screen (see examples
at right below), you will be able to congure the appropriate Pro:Centric settings in the TV. Use the Up/Down arrow keys on the Installer Remote to navigate between elds.
2. In the Pro:Centric Mode eld, use the Left/Right arrow keys
to select the appropriate Pro:Centric Application Mode— GEM, FLASH, HTML, or Conguration Only.
Note: For remote management only, select “Conguration Only.” The TV will search for TV E-Z Installation data down­loads; however, Pro:Centric application data will not be downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will be set to 0.
3. Refer to the appropriate subsection below, depending on the
Pro:Centric server conguration, to complete the remaining elds.
RF Conguration
a) In the Media Type eld, use the Left/Right arrow keys to
select RF.
b) In the Data Channel eld, either key in or use the Left/
Right arrow keys to select the RF channel number that will be used by the Pro:Centric server as its data channel. The Data Channel value can be set from 1 to 135. *
IP Conguration
a) In the Media Type eld, use the Left/Right arrow keys to
select IP.
Note: By default, the Pro:Centric Manual Conguration screen initially shows RF conguration elds. When you select “IP” as the Media Type, the Data Channel and Signal Strength elds are replaced with (IP) Address and Port elds.
b) In the Address and Port elds, either key in or use the
Left/Right arrow keys to select the appropriate values for the Pro:Centric server IP address and port number.
The IP address must match the IPv4 multicast address and the port number must match the port number that is set in the Pro:Centric server.
Z
EZ-Manager Wizard
4
3
1
2
Searching for Pro:Centric Server...
It may take 1 min 32 second(s).
This step automatically searches for the Pro:Centric server.
If there is no Pro:Centric Server installed, you do not need to continue with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.
Status : Tuning channel 49
TV is now searching all of the channels for the data channel...
Back
EZ-Manager Wizard
4
3
1
2
Exit
Manual Pro:Centric
Pro:Centric Manual Configuration
Pro:Centric Mode
Media Type
Data Channel
Signal Strength Signal Quality
Back
GEM
< >
RF
1
No signal
Exit
Pro:Centric Manual Configuration Screen with
RF Media Fields
EZ-Manager Wizard
4
3
1
2
Pro:Centric Manual Configuration
Pro:Centric Mode
Media Type
Addresss
Port
Back
GEM
IP
< >
255
0
Exit
Pro:Centric Manual Configuration Screen with
IP Media Fields
0%
0%
Next
255255255
Next
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
16
(Continued on next page)
206-4234
(Continued from previous page)
EZ-Manager Wizard (Cont.)
4. Once all elds are completed as required, you have two
options (see also note below):
• To save the data entered and exit the wizard, use the arrow
keys to select Exit and then press OK. In the subsequent pop-up conrmation window, select Save and Exit, and then press OK once more. The Pro:Centric application and/or E-Z Installation data will be downloaded to the TV at a later time. This option is useful, in particular, if the Pro:Centric server has not yet been congured.
• To initiate a real-time download of Pro:Centric application and/or E-Z Installation data, use the arrow keys to select Next, and then press OK.
The EZ-Manager Wizard will proceed with the remaining Pro:Centric application and/or E-Z Installation data down­load steps, as shown on the Processing the Pro:Centric Conguration screen.
Note: With RF conguration, Pro:Centric server data must be present on the RF channel selected as the TV’s Data Channel in order for you to select “Next” (you will see a “Data Channel found” message below the signal strength indicator). With IP conguration, Pro:Centric server data must be present via the wired LAN cable connection in order for you to select “Next” (you will see a “IP server found” message below the Port eld).
When the Pro:Centric conguration is complete, an EZ-Manager Conguration Complete screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.
Note: With the EZ-Manager Conguration Complete screen on display, you also have the option to manually turn off or reboot the TV. If desired, select Turn Off or Reboot, respectively, and then press OK on the Installer Remote.
EZ-Manager Wizard
4
3
1
2
EZ-Manager Wizard
2
1
EZ-Manager Wizard
2
1
Pro:Centric Manual Configuration
Are you sure you want to exit the wizard?
!
Pro:Centric Mode
If you select ‘OK’ now, your settings will be lost
< >
and you will exit the setup wizard.
Channel Number
This window will close and you will be returned to
Signal Strength
the previous page automatically in 2 seconds.
Signal Quality
Save and Exit
Back
4
3
Processing the Pro:Centric Configuration...
Downloading the Pro:Centric application files takes a few minutes.
Retrieving files from data channel 75
Application files
Maintenance files
Warning - Do not remove AC power or the signal cables during these steps
3
4
OK
Exit
Please wait...
EZ-Manager Configuration Complete
The TV will turn off in 3 second(s).
Installed Components
Pro:Centric Application Maintenance Files
Reboot
GEM
1
Cancel
No signal
In progress...
Pending...
GEM application downloaded
LT777H_Config.tlx
Turn Off
Next
0%
0%
1%
USB Conguration
Before you being, note the following:
• Each of these functions requires that you have the appropriate le(s) loaded on a USB memory device. If you wish to perform a software upgrade from the USB Download Menu, the software upgrade les must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. Cloning (.tll/.tlx) or FTG Conguration (.tlx) les should simply be stored in the root directory of the USB device.
• If you intend to use the TV Zoning feature on this TV, make sure to assign the TV Zone # in the EZ-Manager’s Zone, Label, and Room Number screen BEFORE continuing with USB Conguration. See “TV Conguration Options” on page 13 for further information.
206-4234
17
EZ-Manager Wizard (Cont.)
• Refer to “Creating an FTG Conguration File using the FTG File Manager” on pages 47 to 48 for information on creating an FTG Conguration (.tlx) le that can be used for FTG Mode via CPU conguration. Also note that to congure the TV for FTG Mode via CPU, the FTG Conguration le must contain an FTG Channel Map. If it does not, any Installer Menu and/or TV setup menu settings contained in the file will be transferred to the TV (as with typical cloning); however, the TV will remain in Pass-through Mode and will not be configured for FTG Mode via CPU.
• Refer to “Custom Master TV Setup” on pages 31 to 34, for information on creating a .tll file that can be used for cloning.
• Ensure the USB device to be used has been formatted with FAT format.
With either the TV Conguration Options or the Zone, Label, and Room Number screen on display, proceed as follows to congure the TV using the USB memory device.
1. Insert the USB memory device that contains the appropriate le(s) into the TV’s USB IN port.
2. Use the arrow keys to select USB Conguration, and then press OK on the Installer Remote.
You will be redirected to the TV’s USB Download Menu. For further information on USB
Download Menu functions, refer to the appropriate section(s) in this document.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Diagnostics
Teach To TV (TLL)
Teach To TV (TLX)
Previous OK
Note: With the USB Download Menu on display, you can press on the Installer Remote at any time to return to the EZ-Manager Wizard.
Note: If you perform a software upgrade from the USB Download Menu, the TV will complete the upgrade and then reboot. Upon restart, the TV will display the EZ-Manager TV Configuration Options screen. If desired, you can re-access the USB Download Menu (to perform additional functions), proceed with conguration via the wizard, or exit the wizard.
Note: (FTG conguration only) When conguration is complete, the TV tunes according to the Start Channel setting in the Installer Menu. If a Start Channel is specied, the TV will tune to that channel; otherwise, the TV will tune to the lowest logical channel in the FTG Channel Map.
3. Remove the USB memory device, and verify that the appropriate configuration is resident on
the TV.
18
206-4234
LG Smart Install Utility
LG Smart Install is a new utility that enables you to congure the TV or update multiple TV conguration elements at one time using les loaded on a USB memory device. You may use LG Smart Install to download any one or all of the following to a TV: an FTG Conguration (.tlx) le, a .tlx le for cloning purposes (no Channel Map), a TV or PTC software update, a splash screen image.
Before you begin, note the following:
• All les must be stored in a folder named “LGSMARTINSTALL” in the root directory of the USB memory device. Also, ensure the USB device has been formatted with FAT format.
• Cloning using a .tll le is only available from the TV’s USB Download Menu.
• Refer to “Creating an FTG Conguration File using the FTG File Manager” on pages 47 to 48 for information on creating an FTG Conguration (.tlx) le that can be used for FTG Mode via CPU conguration. Also note that to congure a TV that is currently in Pass-through Mode for FTG Mode via CPU, the FTG Conguration le must contain an FTG Channel Map. If it does not, any Installer Menu and/or TV setup menu settings contained in the file will be transferred to the TV (as with typical cloning); however, the TV will remain in Pass-through Mode and will not be configured for FTG Mode via CPU.
• Refer to Reference section, “Downloading a Splash Screen using a USB Memory Device,” for splash screen image guidelines.
Caution: Do not unplug the TV power cord or remove the USB memory device during a data download, as doing so may cause the TV to malfunction or harm the USB device, respectively.
The following procedure describes how to use the LG Smart Install utility.
1. If it is not ON already, turn ON the TV.
The next step to access the LG Smart Install utility depends on whether the EZ-Manager Wizard appears on the screen when you turn ON the TV:
• If the wizard is displayed, you can insert the USB memory device that contains the appropriate le(s) into the TV’s USB IN port at any time to initiate the LG Smart Install utility.
The LG Smart Install utility Integrated USB Downloading screen will be displayed (see example on following page). Go to step 3.
• If the wizard is not displayed, insert the USB memory device that contains the appropriate le(s) into the TV’s USB IN port, and continue with step 2.
Note: If you intend to use the TV Zoning feature for location-specic conguration purposes, make sure to assign the TV Zone # in the TV BEFORE continuing with LG Smart Install. If the EZ-Manager is currently active, see “TV Conguration Options” on page 13 for further information. If the TV is currently in Pass-through Mode, see Reference section, “Using the TV Zoning Feature,” for further information.
(Continued on next page)
206-4234
19
LG Smart Install Utility (Cont.)
(Continued from previous page)
2. To access the LG Smart Install utility loading
screen from the TV menus:
Integrated USB Down-
• Press MENU SETTINGS on the Installer Remote to display
the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).
• Use the arrow navigation keys to select/highlight either the
Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the num­ber “7” key a total of seven times.
3. The Integrated USB Downloading screen contains a listing of the les stored in the LGSMARTINSTALL folder on the USB device.
The utility will only ever allow you to select one of each le
type for downloading. For example, if there are two .tlx les in the LGSMARTINSTALL folder, you will only be able to select one of those two les. By default, the rst instance of each le type listed on the screen is selected. To select or de-select a le, respectively, use the Up/Down arrows on the Installer Remote to highlight the lename, and press OK to add or remove the checkmark at the left of the lename.
Note: Use the arrow keys on the Installer Remote to select Previous and press OK, as necessary, to exit the LG Smart
Install utility. If you accessed the utility via the EZ-Manager Wizard, you will be returned to the last screen on display before you inserted the USB device. If you accessed the utility via the TV menus, you will be returned to TV viewing.
4. When you are ready to continue, use the arrow keys on the Installer Remote to select Next, and then press OK.
The TV will show download progress in a new window. Do NOT remove the USB device until downloading is complete. When the download is complete, the TV will briey display an overview of the results in a “Complete” window and then return to TV viewing or reboot (the latter if software has just been downloaded).
5. Remove the USB memory device, and verify that the appropriate configuration is resident on the TV.
Note: (FTG conguration only) When conguration is complete, the TV tunes according to the Start Channel setting in the Installer Menu. If a Start Channel is specied, the TV will tune to that channel; otherwise, the TV will tune to the lowest logical channel in the FTG Channel Map.
USB LG Smart Install Utility
Integrated USB Downloading
Select the configuration file(s) to download, and then select ‘Next’.
xxLT777H-UA00001.TLX
Splash-Image-1366-x-768.jpg
xxLT777H_v3.45.00_usb.epk
Previous
USB LG Smart Install Utility
Downloading Data...
Warning - Do not remove the USB device during this process
Maintenance File
File Name : xxLT777H-UA00001.TLX
Boot Logo File
File Name : Splash-Image-1366-x-768.jpg
Software File
File Name : xxLT777H_v3.45.00_usb.epk
USB LG Smart Install Utility
Complete
The TV will reboot in 2 second(s).
Maintenance File : xxLT777H-UA00001.TLX Boot Logo File : Splash-Image-1366-x-768.jpg Software File (CPU) : xxLT777H_v3.45.00_usb.epk
Installed Components
Next
Complete
Ready
Ready
20
206-4234
Use the Installer Menu to set up, change, or view operational settings. This section describes how to access, use, and exit the Installer Menu from the TV itself; however, you should also refer to the Installer Menu descriptions in this document if you are conguring the TV using LG’s FTG conguration software.
Refer to the table on pages 23 and 24 for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.
Accessing the Installer Menu
1. Turn ON the TV.
If the EZ-Manager Wizard appears on the screen when you turn ON the TV, use the arrow keys on the Installer Remote to select Exit from the Welcome screen and press OK. In the conrmation pop-up window, select OK, and then press OK once more on the Installer Remote to exit the wizard.
2. Using an Installer Remote, press MENU SETTINGS repeatedly until the on-screen display of the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not in Pass-through Mode) no longer toggles, and then press the Installer Menu entry sequence (e.g., 9-8-7-6) + OK to access the Installer Menu.
Note: The default Installer Menu entry sequence is “9876”; however, if Installer Menu item 000 INSTALLER SEQUENCE has been modied, the entry sequence may be one of three additional options. See Installer Menu detailed descriptions for further information.
The Installer Menu opens with item 000 INSTALLER SEQ 000.
Installer Menu
xxLT777H PTC INSTALLER MENU
CPU-CTV
000 INSTALLER SEQ 000
UPN 000-000-000-000 ASIC D279 PTC V1.01.026 CPU V3.45.00
Typical Installer Menu
Note: If the password (entry sequence) is not entered or registered correctly, you will see the message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu header. Once you re-enter the correct password (e.g., press 9-8-7-6 + OK), the Installer Menu will display.
Note: If the TV is not in Pass-through Mode, the Installer Menu is accessible as read-only. Also, if the TV conguration includes a Zone assignment, the TV Zone # will be indicated in the Installer Menu header under the conguration mode indicator described below.
206-4234
21
Installer Menu (Cont.)
As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current conguration mode. The table below lists all possible mode identiers for these TV models.
Acronym Description
CPU-CTV Pass-through Mode with Channel Map in CPU
CPU-FTG FTG Mode via CPU
CPU-P:C Application Tuning Mode via CPU
EBL-FTG FTG Mode via EBL
EBL-LNT LodgeNet PPV Mode
MPI-EXT External MPI Control
PTC-CTV Pass-through Mode with Channel Map in PTC
Using the Installer Menu
Refer to the table starting on the next page for an overview of the available Installer Menu items, including their item numbers, functions, value ranges, and default values.
Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore, some numbers are missing. For example, item 006 will not appear. In addition, items that are dependent on other Installer Menu item settings will not be initially accessible. For example, item 046 STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.
Navigation within the Installer Menu
Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items, or access an item directly by keying in the item number and then pressing MENU SETTINGS. For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU SETTINGS.
Changing Installer Menu Settings
To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or enter a valid value directly. To save the new setting, press OK, or use the Up/Down arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will not be saved.
Exiting the Installer Menu and Activating Settings
After you have adjusted all required Installer Menu item settings, press OK once on the Installer Remote to save your changes; then, press OK again to exit the Installer Menu. Any changes you make will be stored in non-volatile memory.
Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control) settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from the Lock setup menu, will now be disabled, and the individual Parental Control settings will be restored to default values.
22
206-4234
Installer Menu Items 000 through 075
Installer Menu (Cont.)
Menu
Item
Function Value Range Default Value Brief Description of Function
000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.
001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff.
002 AC ON 0 ~ 3 0
003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
004 STRT CHANNEL
005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.
007 STRT VOLUME 0 ~ 63, 255 255
008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.
009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.
010 MUTE DISABLE 0 / 1 0 Set to 1 to disable Mute Function.
011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.
015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.
016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.
017 ALARM 0 / 1 1 Set to 1 to enable Alarm.
020 FEATURE LEVEL 0, 16 ~ 24 0 Determines an additional IR code scheme to which the TV will respond.
021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip (Parental Control) functions.
022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip blocking hours.
023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting set before TV turned OFF.
028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.
029 OLD OCV 0 / 1 0 Set to 1 to change MPI operation to OCV.
030 ACK MASK 0 / 1 0 If set to 1, enables ACK feature of MPI.
031 POLL RATE 20 ~ 169 94 Selects poll rate for MPI.
032 TIMING PULSE 186 ~ 227 207 Sets baud rate for MPI.
035 HDMI1 ENABLE 0 ~ 2, 5, 6 1
039 REAR AUX EN. 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.
041 SIMPLINK EN 0 ~ 3 0 Determines the status of the SIMPLINK feature. (See detailed descriptions.)
046 STRT AUX SRCE 1, 3 ~ 5, 7, 255 7 Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).
047 AUX STATUS 0 / 1 0
053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.
069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.
070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Channel-Time display.
071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display.
073 CH NOT AVBLE 0 / 1 0
075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.
0 ~ 127, 253,
255
255
Set to 1 to enable TV to turn ON when AC power is applied. Set to 2 or 3 to
enable Instant ON when AC power is applied. (See detailed descriptions.)
Channel tuned when TV is turned ON. (Set to 255 to tune to channel
tuned before TV turned OFF.)
Volume level when TV is turned ON. (Set to 255 to use volume level
before TV turned OFF.)
Set to 0 to disable HDMI 1. Set to 1 (DTV Mode) or 2 (PC Mode), as applicable, to enable HDMI 1. Set to 5 (DTV Mode) or 6 (PC Mode), as applicable, to enable HDMI 1 but disable Hot Plug Detect (HPD) circuit.
Set to 1 for MPI Aux source to be reported as a channel number instead of
Channel 0.
If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message is displayed if user direct tunes a channel that is not in the favorite channel list.
206-4234
23
Installer Menu (Cont.)
Installer Menu Items 078 through 122
Menu
Item
Function Value Range Default Value Brief Description of Function
078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.
080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.
081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.
082 CHKSM ERROR 0 / 1 1 Enforces rigid MPI checksum.
083 HANDSHK TIME 0 ~ 5 5
084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.
087 REAR RGB EN. 0, 1, 17 1
088 EN NOISE MUTE 0 / 1 1 If set to 1, audio is muted if no signal is present.
090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.
091 HDMI2 ENABLE 0 ~ 2 1
092 HDMI3 ENABLE 0 ~ 2 1
093 RJP AVAILABLE 0, 1, 2, 5, 6 0
094 SAP MENU EN 0 / 1 1
096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.
097 AUDIO OUTPUT 0 ~ 8
098 PRO:CENTRIC
099 BACK LIGHTING 1 ~ 202, 255
102 ATSC BAND 0 ~ 4 4 Selects ATSC band.
103 ATSC TUNE MODE 0 / 1 1 Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
104 START MINOR CH 0 ~ 255 0 Selects Minor Start Channel. Set to 0 for NTSC.
106 ASP RATIO LOCK 0 / 1 0
116 VIDEO MUTE EN 0 / 1 0 Set to 0 for Normal. Set to 1 for Blank.
117 FACT DEFAULT 0 / 1 0 Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.
118 POWER SAVINGS 1, 3, 7, 9 3
119 DATA CHANNEL
121 UPDATE TIME HR 0 ~ 23, 128 128
122 UPDATE TIME MN 0 ~ 59 0
0 ~ 3
0 ~ 135, 253,
255
7
0
255
255
Relaxes MPI timing to be compatible with PC-based Windows-
controlled systems.
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.
Set to 1 to enable RGB input. Set to 17 for Auto Configure.
Set to 0 to disable HDMI 2. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 2.
Set to 0 to disable HDMI 3. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 3.
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on
Function Menu.
Set as required in accordance with external audio equipment connected to the
TV. See detailed descriptions.
Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for
GEM (Java Application) Mode. Set to 3 for HTML Mode.
Sets the level of the TV picture back lighting. (See detailed descriptions.)
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
power cycle.
Determines the powered status of the embedded b-LAN module and the
GAME CONTROL/MPI port. (See detailed descriptions.)
Set to 0 to disable. Set from 1 to 135 to match the RF channel number used by
the Pro:Centric server as its data channel. Set to 255 to use Auto Search to
find the Pro:Centric RF channel. (See detailed descriptions.)
Sets the Wake For Update hour. The value “128” is displayed as “OFF.” Directly
entering 128 turns the Wake For Update feature OFF.
Sets the minute for Wake For Update.
24
Caution: Installer Menu settings may affect options available from the TV setup menus or the Function Menu.
206-4234
Detailed Descriptions of Installer Menu Items
Installer Menu (Cont.)
000 - INSTALLER SEQUENCE
Species entry sequence to the Installer Menu.
0 = 9876 1 = 4321 2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Management is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain ON, unless there has been activity from either the control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to 1, this allows the TV to turn ON when AC power is applied. Pressing the POWER button is not necessary. This is desirable if the TV is plugged into a switched AC outlet (i.e., a set-top box). Set to 2 or 3 to enable the Instant ON feature (see additional information below). Set to 0 (default) for standard TV turn ON/OFF operation.
The Instant ON feature allows the TV to turn ON when AC power is applied, but with video and audio muted (Muted ON). The TV retains its ON status while appearing to be OFF. Pressing the POWER button toggles Off/On the video and audio mutes, so that the TV appears to turn ON instantly.
If this item is set to 2, the TV will reboot to check for and down-
load updates from the Pro:Centric server at every turn OFF. This setting is not recommended if the TV will be congured with a resident application.
If this item is set to 3, the TV will not reboot to check for and
download updates at turn OFF. This setting is recommended if the TV will be congured with a resident application. In this mode, the check for and download of updates is under application control. Refer to your site-specic documentation for further information on conguring the TV with a resident application.
When AC ON is set to 2 or 3, the TV will reboot once every 24 hours and, if applicable (i.e., item 119 DATA CHANNEL is set), check for and download updates from the Pro:Centric server. The time at which this event occurs depends on the setting of item 121 UPDATE TIME HR. See item 121 description for further information. Once the update cycle is complete, the TV completes the reboot and resumes its Muted ON state.
Note: If set to 1, the TV does not respond to ON/OFF commands from either the remote or the display panel, and the SLEEP TIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency Control)
There are four possible settings for this option:
0 = Broadcast 1 = CATV (default) 2 = HRC 3 = IRC
If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here, and add the channels using the Channel Edit option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial Major Start Channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned ON. If set to 255, the last channel tuned before the TV was turned OFF will be the channel tuned when the TV is turned ON again.
0 = Aux 127 = Map to Major CH 4 1 ~ 125 = Major Ch. # 253 = IP Start Channel 126 = Map to Major CH 3 255 = Last Channel
Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.
Note: 126 and 127 are mapped only in LodgeNet PPV Mode.
Note: The IP Start Channel shown above can only be set in the
FTG File Manager, which is used to congure TV CPUs for FTG Mode. The same applies for the additional Major Channel number range of 128 ~ 135 in Physical tuning and 128~999 in Virtual tuning mode. This means that these values, if set, will only be visible in the read-only Installer Menu when the TV is in FTG Mode via CPU. The read-only display also will show additional information about the channel, for example, the IP address and port number, etc.
005 - CHAN LOCK (Channel Lock)
Channel Lock is ideal if the system must always be on the same channel. Changing channels with the Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).
Generally, this feature is used in connection with item 004 STRT CHANNEL where the Start Channel may, for example, be set to 3 or 4. If the Start Channel is 3, then the TV will remain locked on channel 3.
NOTE: For items 007, 008, and 009 For legacy reasons, the scale used is 0 – 63. The PTC software will translate this to the 0 – 100 scale used by the TV.
To translate a TV volume level to the Installer Menu value, use the following formula:
Installer Value = TV Value x 63 100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV will always select that volume level when it is turned ON. The range of values is 0 to 63, 255. If set to 255, the last volume level before the TV was turned OFF will be the current volume level when the TV is turned ON again.
206-4234
25
Installer Menu (Cont.)
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is set to 63. It is recommended to set the same value on every TV.
Note: The minimum volume level cannot have a value setting higher than the maximum volume level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, some­one cannot set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is set to
0. It is recommended to set the same value on every TV.
Note: The maximum volume level cannot have a value setting lower than the minimum volume level (described above).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.
011 - KEY DEFEAT (Keyboard Defeat)
If set to 1, KEY DEFEAT prevents the end user from accessing the on-screen menu(s) from the display panel—MENU SETTINGS, OK, and menu navigation keys do not function. If set to 0, those keys do function.
Note: Users can always access the menus by pressing MENU SETTINGS on the remote.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers.
Note: The TV clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.
Note: The TV clock must be set before the Alarm function will work.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on “bed number” in a multi-TV single room installation. First determine the IR mode; then select the bed number.
Values IR Mode Bed #
0 Disabled N/A
16 – 24 Multi-code Remote 1 – 9
Note: For further information, see documentation for the accessory package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available to the end user to lter and control or otherwise restrict program­ming content that can appear. Set to 0 to turn the V-Chip feature Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.
Note: This item is not available in the Installer Menu when item 084 PERMANENT BLK is set to 1.
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting congured before the TV was turned OFF when the TV is turned ON.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.
029 - OLD OCV (On Command Video™)
Set to 1 to remap the PTC’s direct tune channels for Aux inputs from 13x to 9x. This allows 2-digit only tuning systems (i.e., legacy OCV) to direct tune Aux inputs. See also Reference section, “TV Aux Input Conguration.”
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI.
26
206-4234
Loading...
+ 59 hidden pages