LG 37LK456C-ZB Schematic

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

LCD TV

SERVICE MANUAL

CHASSIS : LD0EC

MODEL : 37LK456C 37LK456C-ZB

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

Printed in KoreaP/NO : MFL67467602 (1202-REV00)

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS ................................................................... 4

SPECIFICATION ...................................................................................... 6

ADJUSTMENT INSTRUCTION ............................................................... 9

TROUBLE SHOOTING GUIDE ............................................................... 16

BLOCK DIAGRAM ................................................................................. 24

EXPLODED VIEW .................................................................................. 25

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Only for training and service purposes

- 2 -

SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of th e cir cuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exp ose d metallic par t. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

Only for training and service purposes

- 3 -

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board mod-

ule or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specied otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a ammable mixture. Unless specied otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this service manual. CAUTION: Do not connect the test xture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some eld-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classied as “anti-static” can generate electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted oor can generate static electricity sufcient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder ows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

Only for training and service purposes

- 4 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

Only for training and service purposes

- 5 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

.

1. Application range

This specification is applied to the LCD TV used LD0EC chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

(1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C (2) Relative Humidity: 65 % ± 10 % (3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models.

(4) Specification and performance of each parts are followed

ea ch dra wing and speci ficat ion by part number in accordance with BOM.

(5) The receiver must be operated for about 5 minutes prior to

the adjustment.

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

- Safety : CE, IEC specification

- EMC : CE, IEC

4. Model General Specification

No. Item Specication Remarks

EU(PAL Market-36Countries) DTV –T/C & Analog

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Sweden, Denmark, Finland, Norway, Bulgaria

DTV-T & Analog

1 Market

UK, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Ukraine

Analog Only

Kazakhstan, Albania, Bosnia, Serbia, Slovakia

1) PAL-BG

2) PAL-DK

2 Broadcasting system

3 Receiving system

4 Scart Jack (1EA) PAL, SECAM 5 Video Input RCA(1EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60 6 Component Input (1EA) Y/Cb/Cr, Y/Pb/Pr 7 RGB Input RGB-PC Analog(D-SUB 15PIN)

8 HDMI Input (3EA)

9 Audio Input (3EA) RGB/DVI Audio, Component, AV L/R Input

10 SDPIF out (1EA) SPDIF out

11 Earphone out (1EA)

12 USB (1EA)

13 DVB

3) PAL-I/I’

4) SECAM L/L’

5) DVB-T/C/S(ID TV) Analog : Upper Heterodyne

Digital : COFDM, QAM

HDMI1-DTV/DVI HDMI2-DTV HDMI3-DTV

Antenna, AV1, AV2, Component, RGB, HDMI1, HDMI2, HDMI3

For SVC (download) DVIX

DVB-T

DVB-C

DVB-S CI+ : Germany(Astra HD+ )

Scart 1 Jack is Full scart and support RF-OUT(analog).

PC(HDMI version 1.3) Support HDCP Input port is different by model.

CI : UK, Finland, Denmark, Norway, Sweden, Russia,

Spain, Ireland, Luxemburg, Belgium, Netherland

CI+ : France(Canal+), Italy(DGTVi) CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria

CI+ : Switzerland(UPC,Cablecom), Netherland(Ziggo),

Germany(KDG,CWB), Finland(labwise)

Only for training and service purposes

- 6 -

5. Component Input (Y, PB, PR)

No. Resolution H-freq(kHz) V-freq(Hz) Proposed

1 720×480 15.73 60.00 SDTV, DVD 480i

2 720×480 15.63 59.94 SDTV, DVD 480i

3 720×480 31.47 59.94 480p

4 720×480 31.50 60.00 480p

5 720×576 15.625 50.00 SDTV, DVD 625 Line

6 720×576 31.25 50.00 HDTV 576p

7 1280×720 45.00 50.00 HDTV 720p

8 1280×720 44.96 59.94 HDTV 720p

9 1280×720 45.00 60.00 HDTV 720p

10 1920×1080 31.25 50.00 HDTV 1080i

11 1920×1080 33.75 60.00 HDTV 1080i

12 1920×1080 33.72 59.94 HDTV 1080i

13 1920×1080 56.250 50 HDTV 1080p

1920×1080 67.5 60 HDTV 1080p

14

6. RGB Input (PC)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remarks

1 720*400 31.468 70.08 28.321 For only DOS mode

2 640*480 31.469 59.94 25.17 VESA

3 800*600 37.879 60.31 40.00 VESA

4 1024*768 48.363 60.00 65.00 VESA(XGA)

5 1360*768 47.72 59.8 84.75 WXGA FHD model

6 1280*1024 63.981 60.02 108.875 SXGA FHD Model

7 1920*1080 67.5 60 148.5 WUXGA FHD model

Input 848*480 60Hz, 852*480 60Hz → 640*480 60Hz Display

Only for training and service purposes

- 7 -

7. HDMI Input(PC/DTV)

7.1. DTV mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed

1. 720*480 31.469 / 31.5 59.94 / 60 27.00/27.03 SDTV 480P

2. 720*576 31.25 50 54 SDTV 576P

3. 1280*720 37.500 50 74.25 HDTV 720P

4. 1280*720 44.96 / 45 59.94 / 60 74.17/74.25 HDTV 720P

5. 1920*1080 33.72 / 33.75 59.94 / 60 74.17/74.25 HDTV 1080I

6. 1920*1080 28.125 50.00 74.25 HDTV 1080I

7. 1920*1080 26.97 / 27 23.97 / 24 74.17/74.25 HDTV 1080P

8. 1920*1080 33.716/ 33.75 29.976/30.00 74.25 HDTV 1080P

9. 1920*1080 56.250 50 148.5 HDTV 1080P

10. 1920*1080 67.43 / 67.5 59.94 / 60 148.35/148.50 HDTV 1080P

7.2. PC mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remarks

1. 720*400 31.468 70.08 28.321 HDCP

2. 640*480 31.469 59.94 25.17 VESA HDCP

3 800*600 37.879 60.31 40.00 VESA HDCP

4. 1024*768 48.363 60.00 65.00 VESA(XGA) HDCP

6. 1360*768 47.72 59.8 84.75 WXGA HDCP

7. 1280*720 45 60 74.25 HDCP

8. 1280*1024 63.981 60.02 108.875 SXGA HDCP / FHD model

9. 1920*1080 67.5 60 148.5 WUXGA HDCP / FHD model

Only for training and service purposes

- 8 -

ADJUSTMENT INSTRUCTION

1. Application Range

This specification sheet is applied to all of the LCD TV with LD0EC chassis.

2. Designation

(1) The adjustment is according to the order which is designated

and which must be followed, according to the plan

can be changed only on agreeing. (2) Power adjustment : Free Voltage. (3) Magnetic Field Condition: Nil. (4) Input signal Unit: Product Specification Standard. (5) Reserve after operation : Above 5 Minutes (Heat Run) Temperature : at 25 °C ± 5 °C Relative humidity : 65 ± 10 % Input voltage : 220 V, 60 Hz (6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),

DDC Adjustment Jig, Service remote control.

(7) Push the "IN STOP" key - For memory initialization.

Case1 : Software version up

1. After downloading S/W by USB , TV set will reboot automatically.

2. Push “In-stop” key.

3. Push “Power on” key.

4. Function inspection

5. After function inspection, Push “In-stop” key.

Case2 : Function check at the assembly line

1. When TV set is entering on the assembly line, Push “In-stop” key at rst.

2. Push “Power on” key for turning it on.

→ If you push “Power on” key, TV set will recover

channel information by itself.

3. After function inspection, Push “In-stop” key.

3. Main PCB check process

▪ APC - After Manual-Insert, executing APC

* Boot file Download

(1) Execute ISP program "Mstar ISP Utility" and then click

"Config" tab.

(2) Set as below, and then click "Auto Detect" and check "OK"

message. If "Error" is displayed, check connection between computer, jig, and set.

(3) Click "Read" tab, and then load download file(XXXX.bin)

by clicking "Read"

(1)

filexxx.bin

which

(4) Click "Connect" tab. If "Can't" is displayed, check connection

between computer, jig, and set.

(2)

(3)

Please Check the Speed : To use speed between from 200KHz to 400KHz

(5) Click "Auto" tab and set as below. (6) Click "Run". (7) After downloading, check "OK" message.

(4)

filexxx.bin

(5)

(7)...........OK

(6)

* USB DOWNLOAD

(1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low, it didn't work. But your downloaded version is High, USB data is automatically detecting.

(3) Show the message "Copying files from memory". (4) Updating is starting.

(5) Updating Completed, The TV will restart automatically. (6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ ATV test on production line.

Only for training and service purposes

* After downloading, have to adjust Tool Option again.

(1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)

- 9 -

3.1. ADC Process

(1) ADC

- Enter Service Mode by pushing "ADJ" key,

- Enter Internal ADC mode by pushing "►" key at "7. ADC Calibration".

0. Tool Option1

1. Tool Option2

2

. Tool Option3

. Tool Option4

3

4

. Tool Option 5

. Country Group

5

6. Area Option

7

. ADC Calibration ඖ

8. White Balance

9

. 10 Point WB

10

. Test Pattern

1

1. EDID D/L

2. Sub B/C

1

3. Touch Sensitivity Setting

1

EZ ADJUST

<Caution> Using "power on" key of the Adjustment remote

control, power on TV.

* ADC Calibration Protocol (RS232)

NO Item CMD 1 CMD 2 Data 0

Enter Adjust MODE

ADC adjust ADC Adjust A D 1 0

Adjust ‘Mode In’

A A 0 0

ADC Calibration

ADC Comp 480i NG

ADC Comp 1080p NG

ADC RGB NG

Start Reset

When transfer the ‘Mode In’, Carry the command.

Automatically adjustment (The use of a internal pattern)

3.3. EDID data

(1) FHD RGB EDID data

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 00 FF FF FF FF FF FF 0 0 1E 6D a b 10 c 01 0 3 6 8 10 09 78 0A EE 91 A3 54 4C 99 26 20 0F 5 0 5 4 A1 08 00 81 80 61 40 45 40 31 40 01 01 30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 45 00 A0 5A 00 0 0 00 1E 66 21 50 B0 51 00 1B 30 50 40 70 3 6 00 A0 5A 00 0 0 0 0 1E 00 00 00 FD 0 0 3A 60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d 70 d 00 e

(2) FHD HDMI EDID data

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 00 FF FF FF FF FF FF 00 1E 6D a b 10 c 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26 20 0F 50 54 A1 08 00 71 4F 81 80 01 01 01 01 01 01 30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 40 45 00 A0 5A 00 00 00 1E 1B 21 50 A0 51 00 1E 30 50 48 88 35 00 A0 5A 00 00 00 1C 00 00 00 FD 00 3A 60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d 70 d 01 e 80 02 03 26 F1 4E 10 1F 84 13 05 14 03 02 12 20 21 90 22 15 01 26 15 07 50 09 57 07 f A0 f E3 05 03 01 01 1D 80 18 71 1C 16 20 58 2C B0 25 00 A0 5A 00 00 00 9E 01 1D 00 72 51 D0 1E 20 C0 6E 28 55 00 A0 5A 00 00 00 1E 02 3A 80 18 71 38 D0 2D 40 58 2C 45 00 A0 5A 00 00 00 1E 01 1D 00 BC E0 52 D0 1E 20 B8 28 55 40 A0 5A 00 00 00 1E 00 00 F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e

Adjust Sequence ▪ aa 00 00 [Enter Adjust Mode] ▪ xb 00 40 [Component1 Input (480i)] ▪ ad 00 10 [Adjust 480i Comp1] ▪ xb 00 60 [RGB Input (1024*768)] (only LD21B) ▪ ad 00 10 [Adjust 1024*768 RGB] (only LD21B) ▪ aa 00 90 End Adjust mode * Required equipment : Adjustment remote control.

3.2. EDID Download

▪ After enter Service Mode by pushing "ADJ" key. ▪ Enter EDID D/L menu. ▪ Enter "START" by pushing "OK" key.

0. Tool Option1

1. Tool Option2

2

. Tool Option3

. Tool Option4

3

4

. Tool Option 5

. Country Group

5

6. Area Option

7. ADC Calibration

8. White Balance

9

. 10 Point WB

10

. Test Pattern

1

1. EDID D/L

2. Sub B/C

1

3. Touch Sensitivity Setting

1

EZ ADJUST

ඖ

<Caution> Never connect HDMI && D-sub cable when EDID

downloaded.

EDID D/L

HDMI1

HDMI2

HDMI3

RGB

Start Reset

NG

(3) Detail EDID Options are below

a. Product ID

MODEL NAME HEX EDID Table DDC Function

HD/FHD Model 0001 01 00 Analog/Digital

b. Serial No: Controlled on production line. c. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'

Year : '2012' -> '16' fix

d. Model Name(Hex):

cf) TV set’s model name in EDID data is below.

Model name MODEL NAME(HEX)

LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)

e. Checksum: Changeable by total EDID data.

EDID C/S data

FHD

HDMI RGB

Block 0 E2 ED

Check sum

(Hex)

Block 1

99 (HDMI1)

-89 (HDMI2)

79 (HDMI3)

f. Vendor Specific(HDMI)

Input Model name(HEX)

HDMI1 67030C001000B82D

HDMI2 67030C002000B82D

HDMI3 67030C003000B82D

Only for training and service purposes

- 10 -

3.4 Function Check

- Check display and sound

■ Check Input and Signal items.

1) TV

2) AV (SCART / CVBS)

3) COMPONENT (480i)

4) RGB (PC : 1024 x 768 @ 60hz)

5) HDMI

6) PC Audio In * Display and Sound check is executed by Remote control.

<Caution> Not to push the INSTOP key after completion if the function inspection.

▪ Auto adjustment Map(using RS-232C to USB cable)

RS-232C COMMAND [CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End

RS-232C COMMAND [CMD ID DATA]

MIN

CENTER

(DEFAULT)

MAX

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 192

G Gain jh Jb je 00 172 192 192 192

B Gain ji Jc jf 00 192 192 172 192

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

4. Total Assembly line process

4.1. Adjustment Preparation

▪ W/B Equipment condition

CA210 : CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE) LED -> CH14, Test signal: Inner pattern(80IRE)

▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is

adjusted by Target data

Mode Temp Coordinate spec

Cool 13,000 K

Medium 9,300 K

Warm 6,500 K

* Connecting picture of the measuring instrument

(On Automatic control) Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C POWER ON -> Enter the mode of White-Balance, the pattern will come out.

Full White Pattern

RS-232C Communication

X=0.269 (±0.002) Y=0.273 (±0.002)

X=0.285 (±0.002) Y=0.293 (±0.002)

X=0.313 (±0.002) Y=0.329 (±0.002)

<Test Signal> Inner pattern (204gray, 80IRE)

CA-210

COLOR ANALYZER TYPE : CA-210

Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

* Manual W/B process using adjust Remote control.

▪ After enter Service Mode by pushing "ADJ" key, ▪ Enter White Balance by pushing "►" key at "8. White

Balance".

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance ►

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

* After you finished all adjustments, Press "In-start" key and

compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the model's module from factory Jig model.

* Push the "IN STOP" key after completing the function

inspection. And Mechanical Power Switch must be set “ON”.

White Balance

Color Temp.

R-Gain G-Gain B-Gain R-Cut G-Cut B-Cut Test-Pattern Backlight Reset

Cool

172 172 192

64 64

64 ON 100

To Set

* Auto-control interface and directions

(1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).

(2) Adhere closely the Color analyzer(CA210) to the module

less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°).

(3) Aging time

- After aging start, keep the power on (no suspension of power supply) and heat-run over 5 minutes.

- Using 'no signal' or 'POWER ONLY' or the others, check the back light on.

Only for training and service purposes

- 11 -

4.2. EYE-Q function check

(1) Turn on TV. (2) Press “EYE” key on Adjustment remote control. (3) Cover the Eye Q sensor at the front of set for 6 seconds. (4) Check the value of Sensor Data. It must be below 10. If

not so, the Eye Q sensor may have some defect. Change the Eye Q sensor.

(5) Wait for 6 seconds after withdrawing form the Eye Q

sensor.

(6) Check the value of Backlight. It must rise. If not so, the

Eye Q sensor may have some defect. Change the Eye Q sensor.

4.3. Outgoing condition Configuration

■ When pressing IN-STOP key by SVC remocon, Red LED are blinked alternatively. And then automatically turn off.

(Must not AC power OFF during blinking)

5. GND and HI-POT Test

5.1. GND & HI-POT auto-check preparation

- Check the POWER cable and SIGNAL cable insertion condition

6. Model name & Serial number D/L

▪ Press "Power on" key of service remote control.

(Baud rate : 115200 bps) ▪ Connect RS232 Signal Cable to RS-232 Jack. ▪ Write Serial number by use RS-232. ▪ Must check the serial number at the Diagnostics of SET UP

menu. (Refer to below).

6.1. Signal Table

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

CMD : A0h LENGTH : 85~94h (1~16 bytes) ADH : EEPROM Sub Address high (00~1F) ADL : EEPROM Sub Address low (00~FF) Data : Write data CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n Delay : 20ms

6.2. Comand Set

Adjust mode CMD(hex) LENGTH(hex) Description

EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)

* Description

FOS Default write : <7mode data> write

Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,

Phase

Data write : Model Name and Serial Number write in EEPROM,.

5.2. GND & HI-POT auto-check

(1) Pallet moves in the station. (POWER CORD / AV CORD is

tightly inserted) (2) Connect the AV JACK Tester. (3) Controller (GWS103-4) on. (4) GND Test (Auto)

- If Test is failed, Buzzer operates.

- If Test is passed, execute next process (Hi-pot test). (Remove A/V CORD from A/V JACK BOX)

(5) HI-POT test (Auto)

- If Test is failed, Buzzer operates.

- If Test is passed, GOOD Lamp on and move to next proc-

ess automatically.

6.3. Method & notice

(1) Serial number D/L is using of scan equipment. (2) Sett ing of scan equ ipm ent operated by Manufac turing

Technology Group.

(3) Serial number D/L must be conformed when it is produced in

production line, because serial number D/L is mandatory by D-book 4.0.

5.3. Checkpoint

(1) Test voltage

- GND: 1.5 KV / min at 100 mA

- SIGNAL: 3 KV / min at 100 mA

(2) TEST time: 1 second (3) TEST POINT

- GND Test = POWER CORD GND and SIGNAL CABLE GND

- Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL.

(4) LEAKAGE CURRENT: At 0.5 mArms

Only for training and service purposes

- 12 -

* Manual Download(Model Name and Serial Number)

If the TV set is downloaded by OTA or Service man, sometimes model name or serial number is initialized.(Not always) There is impossible to download by bar code scan, so It need Manual download.

1) Press the "Instart" key of Adjustment remote control.

2) Go to the menu "6.Model Number D/L" like below photo.

3) Input the Factory model name or Serial number like photo.

4) Check the model name Instart menu. → Factory name displayed. (ex 32LV3400-ZG)

5) Check the Diagnostics.(DTV country only) → Buyer model displayed.(ex 32LV3400-ZG)

7. CI+ key download

7.1 Download Procedure

(1) Press "Power on" key of a service remote control

(Baud rate : 115200 bps) (2) Connect RS232-C Signal Cable. (3) Write CI+ Key through RS-232-C. (4) Check whether the key was downloaded or not at ‘In Start’

menu. (Refer to below).

7.1.1. Check the method of CI+ Key value

(1) Check the method on Instart menu (2) Check the method of RS232C Command

1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

A A 0 0

2) Check the key download for transmitted command

(RS232: ci 00 10)

CMD 1 CMD 2 Data 0

C I 1 0

3) Result value

- Normally status for download : OKx

- Abnormally status for download : NGx

7.1.2. Check the method of CI+ key value(RS232)

1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

A A 0 0

2) Check the mothed of CI+ key by command

(RS232: ci 00 20)

CMD 1 CMD 2 Data 0

C I 2 0

3) Result value i 01 OK 1d1852d21c1ed5dcx

CI+ Key Value

Only for training and service purposes

- 13 -

8. Commercial Feature inspection

8.1 LG Logo inspection

(1) Turn on TV. (2) Check LG Logo operation when TV is turning on. (Check

LG Logo is displayed well or not.)

8.2 Welcome Screen Function check

(1) Press “IN STOP” key. (2) Turn on TV. (3) Insert USB. (4) Press “MENU” key. (5) Move cursor to OPTION and press “7” key 7 times. (6) Move cursor to “LOGO Image Download” key and select it.

* Must Restore to LG Logo. (9) Press “MENU” key. (10) Move cursor to OPTION and press “7” key 7 times.

(11) Select accurate CPU S/W file and check “LOGO Image”

button. (Press yellow color key on Remote Control.)

(7) Select image file.(Welcome Screen Test Image_720x576.jpg)

(8) Check displayed image status(color, size) when TV is

turning on.

(12)Check LG Logo operation when TV is turning on.

8.3. USB Cloning Function check

Only for training and service purposes

- 14 -

If the clock LED of TV 2 is on and TV 1, 2 had a same TV channels → USB cloning is success!!

● CASE 2. No Clock LED Model

If the auto volume of TV 2 is on and TV 1, 2 had a same TV channels → USB cloning is success!!

8.4. After finishing 10.1 ~ 10.3 inspections, press “IN STOP” key.

Only for training and service purposes

- 15 -

1. Power-up boot check

TROUBLE SHOOTING

Check stand-by Voltage.

P403 9~12pin : +3.5V_ST

ok

Check Micom Voltage.

L404 : +3.5V

ok

Check X201 clock.

24 MHz

ok

Check P403 PWR_ON.

1pin : 3.3V

ok

Check Multi Voltage.

P403 2pin:24V, 17pin:12V

ok

Check IC402/3/7 Output Voltage.

IC402 : 2.5V IC403 : 1.1V IC407 : 1.5V

Q403 : 3.3V

No

Check Power connector.

Replace L404.

Replace X201.

Re-download software.

Replace Power Board.

Replace IC402/3/7, Q403.

okNo

Main B/D 3.5V Line

Short Check

ok

Replace Power board.

No

Replace Mstar(IC101) or Main board.

ok

Check LVDS Power Voltage.

Q409 : 12V

ok

Check Mstar LVDS Output

ok

Check Inverter Control & Error Out.

P403 18 pin : High P403 24 pin : low

ok

Change Module.

No

Replace Q409.

Replace Mstar(IC101) or Main Board.

Check Power Board or Module.

Only for training and service purposes

- 16 -

2. Digital TV Video

Check RF Cable & Signal

ok

Check Tuner 3.3V Power

L3703

ok

Check Tuner 1.8V Power

IC3703 2 pin : 1.8V

ok

Check IF_P/N Signal

TU3700 10/11 Pin

ok

Check Mstar LVDS Output.

3. Analog TV Video

Check RF Cable & Signal.

No

Replace L3703.

No

Replace IC3703.

No

Bad Tuner. Replace Tuner.

No

Replace Mstar(IC101) o r Main Board.

ok

Check Tuner 3.3V Power.

L3703

ok

Check Tuner 1.8V Power.

IC3703 2 pin : 1.8V

ok

Check CVBS Sign al.

TU3700 8 Pin

ok

Check Mstar LVDS Output.

Only for training and service purposes

No

Replace L3703.

Replace IC3703.

Bad Tuner. Replace Tuner.

Replace Mstar(IC101) or Main Board.

- 17 -

4. AV Video

Check input signal format.

Is it supported?

Check AV Cable for damage

for damage or open conductor.

ok

Check JK1604

CVBS Signal Line

R246.

ok

Check CVBS_DET Signal.

ok

Check Mstar LVDS Output.

5. Component Video

Check input signal format.

Is it supported?

ok

Check Component Cable

for damage or open conductor.

No

Replace Jack.

No

Replace R1666.

No

Replace Mstar(IC101) or Main Board.

ok

Check JK1601 or 1603

Y/PB/PR sign al Line.

ok

Check COMP_DET Signal.

ok

Check Mstar LVDS Output.

Only for training and service purposes

No

Replace Jack.

Replace R1615.

Replace Mstar(IC101) o r Main Board.

- 18 -

6. SCART Video

Check input signal format.

Is it supported?

ok

Check Component Cable

for damage or open conductor.

ok

Check JK1602

R/G/B and sync signal Line.

ok

Check SC1_DET Signal.

ok

Check Mstar LVDS Output.

7. RGB Video

No

Replace Jack.

No

Replace R1614.

No

Replace Mstar(IC101) or Main Board .

Check input signal format.

Is it supported?

ok

Check RGB Cable conductors for damage or open conductor.

ok

Check EDID

I2C Signal

R138, R139(SDA,SCL).

ok

Check JK1104

H/V_Sync/R/G/B Signal Line.

ok

Check DSUB_DET.

ok

No

Re-download EDID data ,Replace Mstar(IC101) or Main Board.

No

Replace Jack.

No

Replace R1146 or R1147.

Check Mstar LVDS Output.

Only for training and service purposes

No

Replace Mstar(IC101) or Main board.

- 19 -

8. HDMI Video

Check input signal format.

Is it supported?

ok

Check HDMI Cable conductors for damage or open conductor.

ok

Check EDID

R4033,R4034,R4035,R4036,

R4037,R4038 I2C Signal.

ok

Check JK801, JK802, JK803.

ok

Check HDMI_DET(HPD).

ok

Check HDCP EEPROM(IC103)

Power & I2C Signal

ok

Check HDMI Signal.

No

Replace the defective IC or re-download EDID data.

Replace Jack.

Replace R830,R828,R862.

Replace the defective IC.

Check other set. If no problem, check signal line.

No

Replace Main Board.

ok

Check Mstar LVDS Output.

Only for training and service purposes

No

Replace Mstar(IC101) o r Main Board.

- 20 -

9. All Source Audio

Check the TV Speaker Menu.

(Menu → Sound → TV Speaker)

On

Check AMP IC(IC501) Power

24V or 20V or 15V, 3.3V

ok

Check Mstar AUDIO_MASTER_CLK

R148.

ok

Check AMP I2C Line

R140, R141.

ok

Check Mstar I2S Output

IC501 9,10,11 Pin.

ok

Off

Toggle the Menu.

No

Replace Amp IC(IC501).

No

Replace Mstar(IC101) o r Main Board.

No

Check signal line. Or replace Mstar(IC101).

No

Check signal line. Or replace Mstar(IC101).

Check Output Signal P501

1, 2, 3, 4 pin.

ok

Check Connector & P501.

ok

Check speaker resistance

and connector damage.

No

Replace Audio AMP IC(IC501).

Replace connector. if found to be damaged.

Replace speaker.

Only for training and service purposes

- 21 -

10. Digital TV Audio

Check RF Cable & Signal.

ok

Check Tuner 3.3V Power

L3703.

ok

Check Tuner 1.8V Power.

IC3703 2 pin : 1.8V

ok

Check IF_P/N Sign al

TU3700 10/11 Pin.

ok

Follow procedure

‘9. All source audio’

trouble shooting guide.

11. Analog TV Audio

Check RF Cable & Signal.

No

Replace L3703.

No

Replace IC3703.

No

Bad Tuner. Replace Tuner.

ok

Check Tuner 3.3V Power

L3703.

ok

Check Tuner 1.8V Power

IC3703 2 pin : 1.8V.

ok

Check CVBS Sign al

TU3700 8 Pin.

ok

Follow procedure

‘9. All source audio’

trouble shooting guide.

Only for training and service purposes

No

Replace L3703.

Replace IC3703.

Bad Tubner. Replace Tuner.

- 22 -

12. AV Audio

Check AV Cable for damage

for damage or open conductor.

ok

Check JK1604 & Signal Line.

Replace Jack.

ok

No

Follow procedure

'9. All source audio'

trouble shooting guide.

13. Component / SCART Audio

Check Component Cable

for damage or open conductor.

ok

Check JK1602, JK1603

& Signal Line.

ok

Follow procedure

'9. All source audio'

trouble shooting guide.

No

Replace Jack.

14. RGB Audio

Check Cable conductors

for damage or open conductor.

ok

Check JK1102 & Signal Line.

ok

Follow procedure

'9. All source audio'

trouble shooting guide.

Only for training and service purposes

No

Replace Jack.

- 23 -

BLOCK DIAGRAM

Option

FPC(51P)

LVDS

(FHD/50Hz)

CI Slot

Buffer

74LCX244

FE_TS_DATA[0:7]

IC1202

IC1201

DDR3 1Gb

IC1401 (8M bit)

SERIAL FL ASH

SPI

DDR3 1Gb

MX25L8005M2I

H5TQ1G63BFR

DDR3 Add.

DDR3 Data

IC104 256Kbit

M24M01-HRMN6TP

IC102 (1Gbit )

H5TQ1G63BFR

I2C

NAND FLASH

PCM_A[0:7]

PCM_A[8:14]

S7LR

IC101

TS_DATA[0:7]

PCM_DATA[0:7]

KEY1

SENSOR

_SCL/SDA

IR & LED /

CONTROL

SOFT TOUCH

(TACT SWITCH)

LED_B

LED_R

KEY2

IR

_SCL/SDA

SOFT TOUCH

SPK L/R

NTP7400

Audio AMP

I2S

24M

X-tal

IF +/-

Only for training and service purposes

SIF

TU_CVBS

(LGIT)

SI2176

RS232C

FE_VOUT

Rear

TMDS

CVBS, L/R

CVBS, Y/Pb/Pr, L/R

L/R

RGB/H/V

SC1_R/G/B

SC1_CVBS_IN

SPDIF

MAX3232MAX3232

DP/DM

H/P L/R

TMDS

CVBS, L/R

AV2

USB2.0

HDMI3

H/P OUT

F-SCART

AV2

RGB PC

PC/DVI Audi In

Compone nt1

HDMI1/2(DVI)

- 24 -

SPDIF

RS-232C

Side

800

400

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essenti al that these special safet y parts shoul d be replac ed with the same compo nents as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

521

540

IMPORTANT SAFETY NOTICE

530

810

910

900

LV1

200

A10

* Set + Stand

* Stand Base + Body

120

A5

A4

300

Only for training and service purposes

- 25 -

510

511

A21

A2

IC102

LGE Internal Use Only

NAND01GW3B2CN6E

NC_1

1

NAND_FLASH_1G_NUMONYX

NC_2

2

NC_3

3

NC_4

4

NC_5

5

NC_6

6

RB

7

R

8

E

9

NC_7

10

NC_8

11

12

13

NC_9

14

15

CL

16

AL

17

W

18

WP

19

20

21

22

23

24

NAND_FLASH_1G_SS

EAN61857001

IC102-*2

K9F1G08U0D-SCB0

EAN60762401

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

NC_29

NC_28

NC_27

NC_26

I/O7

I/O6

I/O5

I/O4

NC_25

NC_24

NC_23

VCC_2

VSS_2

NC_22

NC_21

NC_20

I/O3

I/O2

I/O1

I/O0

NC_19

NC_18

NC_17

NC_16

+3.3V_Normal

NC_29

48

NC_28

47

NC_27

46

NC_26

45

I/O7

44

I/O6

43

I/O5

42

I/O4

41

NC_25

40

NC_24

39

NC_23

38

VDD_2

37

VSS_2

36

NC_22

35

NC_21

34

NC_20

33

I/O3

32

I/O2

31

I/O1

30

I/O0

29

NC_19

28

NC_18

27

NC_17

26

NC_16

25

NC_1

NC_2

NC_3

NC_4

NC_5

NC_6

RY/BY

RE

CE

NC_7

NC_8

VCC_1

VSS_1

NC_9

NC_10

CLE

ALE

WE

WP

NC_11

NC_12

NC_13

NC_14

NC_15

22

AR101

C102

10uF

C103

0.1uF

AR102

NAND_FLASH_1G_TOSHIBA

EAN61508001

IC102-*3

TC58NVG0S3ETA0BBBH

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

PCM_A[7]

PCM_A[6]

PCM_A[5]

PCM_A[4]

PCM_A[3]

PCM_A[2]

PCM_A[1]

PCM_A[0]

22

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

/PF_WP

NAND FLASH MEMORY

/PF_OE

/PF_CE0

3.3K

R102

NAND_FLASH_1G_HYNIX

EAN35669102

IC102-*1

H27U1G8F2BTR-BC

NC_1

1

NC_2

2

NC_3

3

NC_4

4

NC_5

5

NC_6

6

R/B

7

RE

8

CE

9

NC_7

10

NC_8

11

VCC_1

12

VSS_1

13

NC_9

14

NC_10

15

CLE

16

ALE

17

WE

18

WP

19

NC_11

20

NC_12

21

NC_13

22

NC_14

23

NC_15

24

/F_RB

+3.3V_Normal

10K

OPT

R104

C

B

E

/PF_CE1

PF_ALE

/PF_WE

Q101 KRC103S

OPT

R105 1K

OPT

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

NC_29

NC_28

NC_27

NC_26

I/O7

I/O6

I/O5

I/O4

NC_25

NC_24

NC_23

VCC_2

VSS_2

NC_22

NC_21

NC_20

I/O3

I/O2

I/O1

I/O0

NC_19

NC_18

NC_17

NC_16

R106

+3.3V_Normal

1K

R109 3.9K

R107

C101

OPT

R1081K

0.1uF

VDD_1

VSS_1

NC_10

NC_11

1K

NC_12

NC_13

NC_14

NC_15

NC_1

1

NC_2

2

NC_3

3

NC_4

4

NC_5

5

NC_6

6

R/B

7

RE

8

CE

9

NC_7

10

NC_8

11

VCC_1

12

VSS_1

13

NC_9

14

NC_10

15

CLE

16

ALE

17

WE

18

WP

19

NC_11

20

NC_12

21

NC_13

22

NC_14

23

NC_15

24

**

AMP_I2C_2.2K

IC103-*1

CAT24C08WI-GT3-H-RECV(TV)

NC_1

NC_2

A2

VSS

HDCP_EEPROM_ON_SEMI_NEW

HDCP EEPROM

HDCP_EEPROM_CATALYST_OLD

R113

4.7K

1

2

3

4

CAT24WC08W-T

A0

A1

A2

VSS

8

7

6

5

IC103

1

$0.199

2

3

4

VCC

WP

SCL

SDA

+3.3V_Normal

C105

0.1uF

VCC

WP

SCL

SDA

C104 8pF OPT

8

7

6

5

VCC

WP

SCL

SDA

R127 4.7K

+3.3V_Normal

C107

0.1uF

R128

R129 22

Addr:10101--

22

I2C_SCL

I2C_SDA

EEPROM

IC104

AT24C256C-SSHL-T

A0

1

A1

2

A0’h

A2

3

GND

4

8

7

6

5

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

<CHIP Config(LED_R/BUZZ)> Boot from SPI CS1N(EXT_FLASH) 1’b0

PCM_A[0-7]

Boot from SPI_CS0N(INT_FLASH) 1’b1

<CHIP Config> (I2S_OUT_BCK,I2S_OUT_MCK,PAD_PWM1PAD_PWM0)

B51_no_EJ : 4’b0000 Boot from 8051 with SPI flash SB51_WOS : 4’b0001 Secure B51 without scramble SB51_WS : 4’b0010 Secure B51 with scramble MIPS_SPE_NO_EJ : 4’b0100 Boot from MIPS with SPI flash MIPS_SPI_EJ_1 : 4’b0101 Boot from MIPS with SPI flash MIPS_SPI_EJ_2 : 4’b0110 Boot from MIPS with SPI flash MIPS_WOS : 4’b1001 Secure MIPS without scramble MIPS_WS : 4’b1010 Scerur MIPS with SCRAMBLE

AUD_MASTER_CLK

NC_29

NC_28

NC_27

NC_26

I/O8

I/O7

I/O6

I/O5

NC_25

NC_24

NC_23

VCC_2

VSS_2

DIMMING

NC_22

NC_21

NC_20

I/O4

I/O3

I/O2

A_DIM

PWM_DIM

C111

2.2uF

I/O1

NC_19

NC_18

NC_17

NC_16

** R140, R141 AMP_I2C_2.2K for only Brazil AMP_I2C_1K for all Country w/o Brazil

R140-*1

2.2K

R141-*1

2.2K

R111 22

R112 22

C106 8pF OPT

I2C

AMP_I2C_1K

R140

1K

I2C_SCL

I2C_SDA

R141

+3.3V_Normal

1K

R161 2.7K

R160 2.7K

R156

R157

C112 100pF 50V

R144

2.2K

R148

56

10K

100

R145

2.2K

R115

R116

R117

1K

OPT

R118

1K

+3.3V_Normal

1K

OPT

1K

SENSOR_SDA

R152

1K

R123

1K

R165

1K

OPT

R121

R153

R124

1K

PWM0

PWM2

AMP_SDA AMP_SCL I2C_SDA

I2C_SCL

SENSOR_SCL

PM MODEL OPTION

R174 10K TOUCH_KEY

OPT

R178 100

OPT

R179 100

R175 10K TACT_KEY

LED_R/BUZZ

AUD_SCK AUD_MASTER_CLK_0

PWM1

PWM0

/CI_CD1 /CI_CD2

to delete CI or gate for

for SYSTEM/HDCP EEPROM&URSA3

+3.5V_ST

TOUCH_KEY

S/T_SDA S/T_SCL

+3.5V_ST

R177 10K PWM_BUZZ/IIC_LED

PM_MODEL_OPT_0

PM_MODEL_OPT_1

R176 10K PWM_LED

+5V_Normal

OPT

R12022 R12222

OPT

I2C_SCL I2C_SDA

RGB_DDC_SDA RGB_DDC_SCL

R149

4.7K

SENSOR_SCL SENSOR_SDA

R132 10K

R133 10K

TOUCH_KEY

R143

4.7K

PCM_D[0-7]

PCM_A[0-14]

/PCM_REG

/PCM_OE

/PCM_WE /PCM_IORD /PCM_IOWR

/PCM_CE /PCM_IRQA

/PCM_CD

/PCM_WAIT

PCM_RST

USB1_OCD USB1_CTL

PCM_5V_CTL ERROR_OUT

PM_TXD

PM_RXD MODEL_OPT_6 MODEL_OPT_7

PWM0 PWM1 PWM2

LED_B/LG_LOGO

LED_R/BUZZ

KEY1 KEY2

SCART1_MUTE

R166 22

R167 22 R168 22 R169 22 R170 22

EDID_WP

PCM_D[0] PCM_D[1] PCM_D[2] PCM_D[3] PCM_D[4]

PCM_D[5]

PCM_D[6] PCM_D[7]

PCM_A[0] PCM_A[1] PCM_A[2] PCM_A[3] PCM_A[4] PCM_A[5] PCM_A[6] PCM_A[7] PCM_A[8] PCM_A[9] PCM_A[10] PCM_A[11] PCM_A[12] PCM_A[13] PCM_A[14]

C109

C108

0.1uF

OPT

R13022 R13122

R136 22

R137 22

R138 22

R139 22

2SC3052

Q807

W21 AA18 AB22 AE20 AA15 AE21 AB21

Y15

W20

V20

W22 AB18 AA20 AA21

Y19 AB17

Y16 AB19 AB20 AA16 AA19 AC21 AA17

Y20

AB15 AA22 AD22 AD20

AD21 AC20

Y18

Y21

Y22

U21

V21

R20

T20

U22

D4

E4 N25 N24

B8

A8

P23 P24

D2

D1

P21 N23 P22 R21 P20

F6

R11922

H6

G5

G4

J5

R10122

J4

R16322 R16422

R23

R24 R25 T21 T22

C

B

E

IC101

LGE2112-T8

PCMDATA[0]/GPIO126 PCMDATA[1]/GPIO127 PCMDATA[2]/GPIO128 PCMDATA[3]/GPIO120 PCMDATA[4]/GPIO119 PCMDATA[5]/GPIO118 PCMDATA[6]/GPIO117 PCMDATA[7]/GPIO116

PCMADR[0]/GPIO125 PCMADR[1]/GPIO124 PCMADR[2]/GPIO122 PCMADR[3]/GPIO121 PCMADR[4]/GPIO99 PCMADR[5]/GPIO101 PCMADR[6]/GPIO102 PCMADR[7]/GPIO103 PCMADR[8]/GPIO108 PCMADR[9]/GPIO110 PCMADR[10]/GPIO114 PCMADR[11]/GPIO112 PCMADR[12]/GPIO104 PCMADR[13]/GPIO107 PCMADR[14]/GPIO106

PCMREG_N/GPIO123

PCMOE_N/GPIO113 PCMWE_N/GPIO197 PCMIORD_N/GPIO111 PCMIOWR_N/GPIO109

PCMCE_N/GPIO115 PCMIRQA_N/GPIO105 PCMCD_N/GPIO130 PCMWAIT_N/GPIO100 PCM_RESET/GPIO129

PCM2_CE_N/GPIO131 PCM2_IRQA_N/GPIO132 PCM2_CD_N/GPIO135 PCM2_WAIT_N/GPIO133 PCM2_RESET/GPIO134

UART1_TX/GPIO43 UART1_RX/GPIO44 UART2_TX/GPIO65 UART2_RX/GPIO64 UART3_TX/GPIO47 UART3_RX/GPIO48

I2C_SCKM2/DDCR_CK/GPIO72 I2C_SDAM2/DDCR_DA/GPIO71

DDCA_DA/UART0_TX DDCA_CK/UART0_RX

PWM0/GPIO66 PWM1/GPIO67 PWM2/GPIO68 PWM3/GPIO69 PWM4/GPIO70 PWM_PM/GPIO199

SAR0/GPIO31 SAR1/GPIO32 SAR2/GPIO33 SAR3/GPIO34 SAR4/GPIO35

S7LR_DIVX_MS10

PM_SPI_SCZ1/GPIO_PM[6]/GPIO12

PM_SPI_SCZ2/GPIO_PM[10]/GPIO16

VSYNC_LIKE/GPIO145

SPI1_CK/GPIO201 SPI1_DI/GPIO202 SPI2_CK/GPIO203 SPI2_DI/GPIO204

AMP_RESET 5V_DET_HDMI_1 5V_DET_HDMI_2 5V_DET_HDMI_4

AV_CVBS_DET

DSUB_DET

SC1/COMP1_DET

HP_DET

SIDEAV_DET

TUNER_RESET

R171

MODEL_OPT_0

10K

MODEL_OPT_1

AMP_SCL

AMP_SDA MODEL_OPT_2 DEMOD_RESET

NF_CE1Z/GPIO138

NF_WPZ/GPIO198 NF_CEZ/GPIO137 NF_CLE/GPIO136 NF_REZ/GPIO139 NF_WEZ/GPIO140 NF_ALE/GPIO141 NF_RBZ/GPIO142

GPIO_PM[0]/GPIO6

PM_UART_TX/GPIO_PM[1]/GPIO7

GPIO_PM[2]/GPIO8 GPIO_PM[3]/GPIO9

GPIO_PM[4]/GPIO10

PM_UART_RX/GPIO_PM[5]/GPIO11

GPIO_PM[7]/GPIO13 GPIO_PM[8]/GPIO14 GPIO_PM[9]/GPIO15

GPIO_PM[11]/GPIO17

PM_SPI_SCK/GPIO1

PM_SPI_CZ0/GPIO_PM[12]/GPIO0

PM_SPI_SDI/GPIO2 PM_SPI_SDO/GPIO3

TS0CLK/GPIO87

TS0VALID/GPIO85

TS0SYNC/GPIO86

TS0DATA_[0]/GPIO77 TS0DATA_[1]/GPIO78 TS0DATA_[2]/GPIO79 TS0DATA_[3]/GPIO80 TS0DATA_[4]/GPIO81 TS0DATA_[5]/GPIO82 TS0DATA_[6]/GPIO83 TS0DATA_[7]/GPIO84

TS1CLK/GPIO98 TS1VALID/GPI96 TS1SYNC/GPIO97

TS1DATA_[0]/GPIO88 TS1DATA_[1]/GPIO89 TS1DATA_[2]/GPIO90 TS1DATA_[3]/GPIO91 TS1DATA_[4]/GPIO92 TS1DATA_[5]/GPIO93 TS1DATA_[6]/GPIO94 TS1DATA_[7]/GPIO95

0

R172

OPT

0

OPT

R173

GP3_S7LR

FLASH/EEPROM/GPIO

AE18 AC17 AD18 AC18 AC19 AD17 AE17 AD19

H5 K6 K5 J6 K4 L6 C2 L5 M6 M5 C1 M4

A2

R15422

D3 B2

OPT

B1

for SERIAL FLASH

Y14 AA10 Y12

Y13 Y11 AA12 AB12 AA14 AB14 AA13 AB11

AC15 AD15 AC16

AD16 AE15 AE14 AC13 AC14 AD12 AD13 AD14

S7LR_DIVX_MS10

LGE2112-T8

C7

GPIO36

E6

GPIO37

F5

GPIO38

B6

GPIO39

E5

GPIO40

D5

GPIO41

B7

GPIO42

E7

GPIO45

F7

GPIO46

AB5

GPIO49

AB3

GPIO50

A9

GPIO51

F4

GPIO52

AB1

I2C_SCKM0/GPIO53

N6

I2C_SDAM0/GPIO54

AB2

GPIO73

AC2

GPIO74

AR103

22

AR104

22

R13422

R13522

R11022 R11422

R14222 R14733 R14633

R15133

CI_TS_DATA[0] CI_TS_DATA[1] CI_TS_DATA[2] CI_TS_DATA[3] CI_TS_DATA[4] CI_TS_DATA[5] CI_TS_DATA[6] CI_TS_DATA[7]

FE_TS_DATA[0] FE_TS_DATA[1] FE_TS_DATA[2] FE_TS_DATA[3] FE_TS_DATA[4] FE_TS_DATA[5] FE_TS_DATA[6] FE_TS_DATA[7]

IC101

/PF_WP /PF_CE0 /PF_CE1 /PF_OE /PF_WE

PF_ALE

/F_RB

POWER_DET

PM_TXD INV_CTL RL_ON

POWER_ON/OFF_1

PM_RXD

/FLASH_WP SIDE_HP_MUTE

PANEL_CTL

PM_MODEL_OPT_0

AMP_MUTE

SPI_SCK /SPI_CS SPI_SDI SPI_SDO

CI_TS_CLK CI_TS_VAL CI_TS_SYNC

CI_TS_DATA[0-7]

from CI SLOT

FE_TS_CLK FE_TS_VAL_ERR FE_TS_SYNC

FE_TS_DATA[0-7]

Internal demod out

S7LR_DIVX

IC101-*1

LGE2111-TE

C7

GPIO36

E6

GPIO37

F5

GPIO38

B6

GPIO39

E5

GPIO40

D5

GPIO41

B7

GPIO42

E7

GPIO45

F7

GPIO46

AB5

GPIO49

AB3

GPIO50

A9

GPIO51

F4

GPIO52

AB1

I2C_SCKM0/GPIO53

N6

I2C_SDAM0/GPIO54

AB2

GPIO73

AC2

GPIO74

NEED TO SWAP LVDS POLARITY

AB25

LVA0P

AB23

LVA0N

AC25

LVA1P

AB24

LVA1N

AD25

LVA2P

AC24

LVA2N

AE23

LVA3P

AC23

LVA3N

AC22

LVA4P

AD23

LVA4N

V23

LVB0P

U24

LVB0N

V25

LVB1P

V24

LVB1N

W25

LVB2P

W23

LVB2N

AA23

LVB3P

Y24

LVB3N

AA25

LVB4P

AA24

LVB4N

AE24

LVACKP

AD24

LVACKN

Y23

LVBCKP

W24

LVBCKN

T25

GPIO196

U23

GPIO193

T24

GPIO194

T23

GPIO195

OLP

applied on only SMALL PCB

20110511

1

GPIO196 GPIO193 GPIO194 GPIO195

RXA0RXA0+ RXA1RXA1+ RXA2RXA2+ RXA3RXA3+ RXA4RXA4+

RXB0RXB0+ RXB1RXB1+ RXB2RXB2+ RXB3RXB3+ RXB4RXB4+

RXACKRXACK+ RXBCKRXBCK+

MODEL_OPT_3 MODEL_OPT_4 MODEL_OPT_5

OLP

LVA0P LVA0N LVA1P LVA1N LVA2P LVA2N LVA3P LVA3N LVA4P LVA4N

LVB0P LVB0N LVB1P LVB1N LVB2P LVB2N LVB3P LVB3N LVB4P LVB4N

LVACKP LVACKN LVBCKP LVBCKN

AB25 AB23 AC25 AB24 AD25 AC24 AE23 AC23 AC22 AD23

V23 U24 V25 V24 W25 W23 AA23 Y24 AA25 AA24

AE24 AD24 Y23 W24

T25 U23 T24 T23

TP100

MODEL OPTION

LGE Internal Use Only

IF_AGC_SEL

LNA2_CTL

RF_SWITCH_CTL

AV_CVBS_IN2

OPT

R201 100

BOOSTER_OPT

R202

RF_SW_OPT

R203

OPT

R204 100

OPT

R4031 100

OPT

R4032 100

OPT

R4040 100

OPT

R4039 100

CK+_HDMI1 CK-_HDMI1 D0+_HDMI1 D0-_HDMI1 D1+_HDMI1 D1-_HDMI1 D2+_HDMI1 D2-_HDMI1 DDC_SDA_1 DDC_SCL_1 HPD1

PM_MODEL_OPT_1

CK+_HDMI4

HDMI

CK-_HDMI4 D0+_HDMI4 D0-_HDMI4 D1+_HDMI4 D1-_HDMI4 D2+_HDMI4 D2-_HDMI4 DDC_SDA_4 DDC_SCL_4 HPD4

CK+_HDMI2 CK-_HDMI2 D0+_HDMI2 D0-_HDMI2 D1+_HDMI2 D1-_HDMI2 D2+_HDMI2 D2-_HDMI2 DDC_SDA_2 DDC_SCL_2 HPD2

CEC_REMOTE_S7

DSUB_HSYNC DSUB_VSYNC

DSUB_R+

DSUB_G+

DSUB

DSUB_B+

SCART1_RGB/COMP1

SC1_ID SC1_FB

SC1_R+/COMP1_Pr+

SC1_G+/COMP1_Y+

SC1_B+/COMP1_Pb+

SC1_SOG_IN

COMP2_Pr+

COMP2_Y+

COMP2

COMP2_Pb+

TU_CVBS

SC1_CVBS_IN

AV_CVBS_IN

SIDEAV_CVBS_IN

AV_CVBS_IN2

DTV/MNT_VOUT

CVBS In/OUT

+3.3V_Normal

PIN NAME

MODEL_OPT_0

MODEL_OPT_1

MODEL_OPT_2 MODEL_OPT_3 MODEL_OPT_4 MODEL_OPT_5

MODEL_OPT_6

MODEL_OPT_7B8A8

OPT

R290 1K

100

R293 1K

R291 1K

R294 1K

DVB_S

R4028 1K

NON_DVB_S

R4030 1K

OLED

3D

R4027 1K

NON_OLED

NON_3D

R4029 1K

R206 1K

R207 1K

DVB_T2

PHM_ON

R208 1K

PHM_OFF

NON_DVB_T2

R209 1K

HD

R226 1K

R211 1K

MODEL_OPT_0 MODEL_OPT_1 MODEL_OPT_2 MODEL_OPT_3 MODEL_OPT_4 MODEL_OPT_5 MODEL_OPT_6 MODEL_OPT_7

FHD

R212 1K

R227 1K

LGE2112-T8

S7LR_DIVX_MS10

RXACKP RXACKN RXA0P RXA0N RXA1P RXA1N RXA2P RXA2N DDCDA_DA/GPIO24 DDCDA_CK/GPIO23 HOTPLUGA/GPIO19

HOTPLUGB/GPIO20

RXCCKP RXCCKN RXC0P RXC0N RXC1P RXC1N RXC2P RXC2N DDCDC_DA/GPIO28 DDCDC_CK/GPIO27 HOTPLUGC/GPIO21

RXDCKP RXDCKN RXD0P RXD0N RXD1P RXD1N RXD2P RXD2N DDCDD_DA/GPIO30 DDCDD_CK/GPIO29 HOTPLUGD/GPIO22 CEC/GPIO5

HSYNC0 VSYNC0 RIN0P RIN0M GIN0P GIN0M BIN0P BIN0M SOGIN0

HSYNC1 VSYNC1 RIN1P RIN1M GIN1P GIN1M BIN1P BIN1M SOGIN1

HSYNC2 RIN2P RIN2M GIN2P GIN2M BIN2P BIN2M SOGIN2

CVBS0 CVBS1 CVBS2 CVBS3 CVBS4 CVBS5 CVBSOUT0 CVBSOUT1

VCOM

TP211

R4026

C203

1000pF

OPT

10K

R4023

R4033 22 R4034 22

R4035 22 R4036 22

R4038 22 R4037 22

R4024 R4025

2.4K

R237 33 R238 68 R239 R240 R241 33 R242 68

R244 33 R245 33 R246 33 R4016 33

R249 33

R252 68

Close to MSTAR

510

510 R228 33 R229 68 R230 33 R231 68 R232 33 R233 68

R253 33 R254 68 R255

33

R256

68 R257 33 R258 68

R236 0

NON_EU

33 68 C221 0.047uF

J2 J3 K3 J1 K2 K1 L2 L3 T5 T4 V5

R5

AE9 AC9

AC10

AD9 AC11 AD10 AE11 AD11

AE8

AD8

AC8

F2 F3 G3 F1 G2 G1 H2 H3 R6 U6 P5 R4

P2

0.047uF

R3 N2 P3 N3 N1 M3 M2 M1

V2 V3 U3 U2 T1 T2 R2 R1 T3

AA2

Y2

AA3

W2 Y3 V1 W3 W1

AA8

Y4 W4

AA5

Y5

AA4

Y6

AA1

AB4

C204 0.047uF C205 0.047uF C4060 C206 0.047uF C207 0.047uF C208 0.047uF C209 0.047uF C210 1000pF

C211 0.047uF C212 0.047uF C213 C214 C215 C216 C217 1000pF

C218 0.047uF C219 0.047uF C220 0.047uF

C222 0.047uF C223 0.047uF C224 1000pF

C225 0.047uF C226 0.047uF C227 0.047uF C4057 0.047uF

C230 0.047uF

TP210

C233 0.047uF

IC101

I2S_OUT_BCK/GPIO156 I2S_OUT_MCK/GPIO154

ET_RXD[0]/RP/GPIO60 ET_TXD[0]/TP/GPIO57

ET_RXD[1]/RN/GPIO63

ET_TXD[1]/LED1/GPIO56

ET_TX_CLK/TN/GPIO59

MODEL OPTION

PIN NO.

AB3

PHM_OFF

F4 AB2

NON_DVB_T2

NON_3D

T25

NON_OLED

U23

NON_DVB_S

T24

IF_AGC RF_AGC

I2C_SCKM1/GPIO75 I2C_SDAM1/GPIO76

SPDIF_IN/GPIO152

SPDIF_OUT/GPIO153

USB0_DM USB0_DP

USB1_DM USB1_DP

I2S_IN_BCK/GPIO150

I2S_IN_SD/GPIO151 I2S_IN_WS/GPIO149

I2S_OUT_SD/GPIO157

I2S_OUT_WS/GPIO155

AUOUTL0 AUOUTL2 AUOUTL3 AUOUTR0 AUOUTR2 AUOUTR3

EARPHONE_OUTL EARPHONE_OUTR

ET_TX_EN/GPIO58

ET_MDC/GPIO61

ET_MDIO/GPIO62

ET_COL/LED0/GPIO55

IRIN/GPIO4

HWRESET

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

LOW

FHD

READY

VIFP VIFM

IP IM

SIFP SIFM

XIN

XOUT

AUL0 AUR0 AUL1 AUR1 AUL2 AUR2 AUL3 AUR3 AUL4 AUR4

AUVRM

AUVAG AUVRP

ARC0

AC4 AD3

AC3 AE3

AD4 AC5

AD2 AE2

AE6 AD6

AD1 AC1

D7 D6

E3 E2

AC12 AE12

C8 D8 D9

B10 C9 B9

C10

AB9 AA11 Y9 AA9 AA7 AB8 Y8 Y10 AC7 AD7

W6 V6 V4 Y7 W5 U5

AD5

AE5 AC6

AA6

L203 H/P_FILTER10uH

AB6

L205 H/P_FILTER10uH

C6 C5

A6 C4

B5 C3 A3 B3 B4

N4

R210 33

T6 N5

HIGH

HD

PHM_ON

DVB_T2

3D

OLED

DVB_S

READEY

READY

TUNER_I2C

1M

R287

R297 0

R296 100

C236 2.2uF C237 C238 2.2uF C239 C4059 2.2uF

C242 C243 2.2uF C244 2.2uF C245 2.2uF

TP207 TP208

TP209

C249

4.7uF

H/P_NON_FILTER

L203-*1

CM2012F5R6KT

L205-*1

CM2012F5R6KT

H/P_NON_FILTER

KOR_EMS_Improvement

Close to MSTAR

R288 100

R289 100

C250 0.1uF C251 0.1uF

ANALOG SIF Close to MSTAR

+3.3V_Normal

L227 BLM18PG121SN1D

C4064

0.1uF

TU_SCL TU_SDA

C261 22pF

X201 24MHz

C262 22pF

OPT

R21322 R21422

2.2uF

C253

1uF

R260-*1 0

H/P_NON_FILTER

R261-*1 0

H/P_NON_FILTER

R260-*2 0

R261-*2 0

C231 0.047uF

C257 0.1uF

C258 0.1uF

R4002 47 R4003 47

FULL_NIM FULL_NIM

C256

0.1uF

H/P_NON_FILTER

KOR_EMS_Improvement

R4019

10K

R4004 0 R4001 0

CI_DET SPDIF_OUT

AMP_SCL

AMP_SDA DEMOD_SCL DEMOD_SDA

COMP2_DET

BLM18SG121TN1D

C263 10uF

C272-*1

4.7uF 10V

C268-*1

4.7uF 10V

C272-*2 10uF

6.3V

C268-*2 10uF

6.3V

IR

HDMI_ARC

SOC_RESET

C4067 OPT

OPT

C264

1000pF

OPT

Close to MSTAR

L202

R260

200

R4020

0

H/P_FILTER

R261

H/P_FILTER

C268 10uF

6.3V

SOC_RESET

C4068 100pF

C4069 100pF

TU_SIF

C4065

0.047uF 25V

SC1/COMP1_L_IN SC1/COMP1_R_IN AV_L_IN AV_R_IN SIDEAV_L_IN SIDEAV_R_IN COMP2_L_IN

COMP2_R_IN PC_L_IN PC_R_IN

H/P_FILTER

200

H/P_FILTER C272 10uF

6.3V

+3.5V_ST

C200

4.7uF 10V

D200 KDS181

DTV_IF

IF_P_MSTAR

IF_N_MSTAR

IF_AGC_MAIN

SIDE USB

AUDIO IN

TMUE312GAB

R200

62K

SIDE_USB_DM

SIDE_USB_DP

AUD_SCK AUD_MASTER_CLK_0 AUD_LRCH

AUD_LRCK

SCART1_Lout

SCART1_Rout

H/P OUT

HP_LOUT HP_ROUT

SWITCH

SW200

43

5 SWITCH

R205

1 2

100

R217

10

C201

0.1uF

I2S_I/F

AUDIO OUT

SOC_RESET

+1.10V_VDDC

10uFC275

10uFC228

+3.3V_Normal

0.1uF

C4043

C4044 0.1uF

Normal 2.5V

+2.5V_Normal

L211

BLM18PG121SN1D

L229

BLM18PG121SN1D

L219

BLM18PG121SN1D

BLM18SG121TN1D

Close to IC with width trace

10uFC276

C277 0.1uF

C280 0.1uF

VDD33

L204

BLM18PG121SN1D

10uFC284

AVDD_AU33

L208

BLM18PG121SN1D

AVDD2P5

AVDD2P5:172mA

C269

C270

10uF

0.1uF

AVDD2P5_MOD

C4070

0.1uF 16V

AVDD25_PGA

C4027

0.1uF

L223

+1.5V_DDR

C4046

0.1uF

STby 3.5V

+3.5V_ST

L206

BLM18PG121SN1D

VDDC 1.05V

OPT

C283 0.1uF

C292 0.1uF

OPT

C299 0.1uF

C4006 0.1uF

C4011 0.1uF

OPT

C4013 0.1uF

Normal Power 3.3V

10uFC4001

10uFC293

OPT

C4007 0.1uF

C240

0.1uF

C271

0.1uF

AVDD25_PGA:13mA

AVSS_PGA

C241

0.1uF

C273

0.1uF

C4012 0.1uF

C4014 0.1uF

C274

0.1uF

C4020 0.1uF

C4025 0.1uF

C4031 0.1uF

DDR3 1.5V

AVDD_DDR0:55mA

L209

BLM18PG121SN1D

OPT

C281

C278

C290

10uF

OPT

AVDD_DDR1:55mA

RSDS Power OPT

AVDD_NODIE:7.362mA

AVDD_NODIE

C286

C252

0.1uF

C4019 0.1uF

C265 0.1uF

C267 0.1uF

C4036

0.1uF

+1.10V_VDDC

BLM18PG121SN1D

C4024 0.1uF

0.1uF

C232 0.1uF

AVDD_MIU

C4038

0.1uF

L228

+1.10V_VDDC

FB_CORE

MIUVDDC

AVDD2P5

AVDD2P5_MOD

AVDD25_PGA

AVSS_PGA

AVDD_NODIE

VDD33

C4045 1uF

AVDD_AU33

VDD33

AVDD_MIU

C4009

0.1uF C4042

0.1uF

MIUVDDC

C4062

C4071

0.1uF

10uF

GP3_S7LR

MAIN2, HW OPT 2

VDDC : 2026mA

LGE2112-T8

S7LR_DIVX_MS10

K12

AVDDLV_USB

G9

VDDC_1

H9

VDDC_2

K10

VDDC_3

K11

VDDC_4

L10

VDDC_5

M12

VDDC_6

M13

VDDC_7

N12

VDDC_8

P14

VDDC_9

P15

VDDC_10

R10

VDDC_11

R14

VDDC_12

R15

VDDC_13

T10

VDDC_14

P10

AVDD1P0

P19

FB_CORE

R16

AVDDL_MOD

L11

AVDD10_LAN

M14

DVDD_DDR

W9

AVDD2P5_ADC_1

W10

AVDD2P5_ADC_2

W11

AVDD2P5_ADC_3

W12

AVDD25_REF

Y17

AVDD25_LAN

V18

AVDD_MOD_1

U19

AVDD_MOD_2

W14

AVDD25_PGA

W15

AVSS_PGA

U7

AVDD_NODIE

L7

AVDD_DVI_USB_1

M7

AVDD_DVI_USB_2

P7

AVDD3P3_MPLL

R7

AVDD_DMPLL

M19

DVDD_NODIE

V7

AVDD_AU33

W7

AVDD_EAR33

R19

VDDP_1

T19

VDDP_2

W18

AVDD_LPLL_1

W19

AVDD_LPLL_2

V19

VDDP_NAND

J17

AVDD_DDR0_D_1

K15

AVDD_DDR0_D_2

K16

AVDD_DDR0_D_3

L15

AVDD_DDR0_C

K17

AVDD_DDR1_D_1

L17

AVDD_DDR1_D_2

M17

AVDD_DDR1_D_3

L16

AVDD_DDR1_C

E9

GND_EFUSE

A23

GND_1

B17

GND_2

C23

GND_3

A5

GND_4

C11

GND_5

C19

GND_6

C22

GND_7

D14

GND_8

D18

GND_9

D19

GND_10

E17

GND_11

E18

GND_12

E19

GND_13

E22

GND_14

F8

GND_15

F17

GND_16

F18

GND_17

F19

GND_18

G8

GND_19

H8

GND_20

N22

GND_21

N21

GND_22

N20

GND_23

M22

GND_24

M21

GND_25

M20

GND_26

F10

GND_27

V15

GND_28

W16

GND_29

V8

GND_30

T18

GND_31

+1.10V_VDDC

IC101

GND_100 GND_101 GND_102 GND_103 GND_104 GND_105 GND_106 GND_107 GND_108 GND_109 GND_110 GND_111 GND_112 GND_113 GND_114 GND_115 GND_116 GND_117 GND_118 GND_119 GND_120 GND_121 GND_122 GND_123 GND_124 GND_125 GND_126 GND_127 GND_128 GND_129 GND_130 GND_131 GND_132 GND_133 GND_134 GND_135 GND_136

20110511

GND_32 GND_33 GND_34 GND_35 GND_36 GND_37 GND_38 GND_39 GND_40 GND_41 GND_42 GND_43 GND_44 GND_45 GND_46 GND_47 GND_48 GND_49 GND_50 GND_51 GND_52 GND_53 GND_54 GND_55 GND_56 GND_57 GND_58 GND_59 GND_60 GND_61 GND_62 GND_63 GND_64 GND_65 GND_66 GND_67 GND_68 GND_69 GND_70 GND_71 GND_72 GND_73 GND_74 GND_75 GND_76 GND_77 GND_78 GND_79 GND_80 GND_81 GND_82 GND_83 GND_84 GND_85 GND_86 GND_87 GND_88 GND_89 GND_90 GND_91 GND_92 GND_93 GND_94 GND_95 GND_96 GND_97 GND_98 GND_99

G10 G11 G12 G13 G14 G17 G18 G19 G24 H11 H12 H13 H14 H15 H16 H17 H18 H19 J9 J10 J11 J12 J13 J14 J15 J16 J18 J19 J25 K9 K13 K14 H10 K18 K19 K22 L8 L9 J8 L12 L13 L18 L19 M8 K8 M10 M11 L14 M15 M16 M18 M25 N10 N11 N13 N14 N15 N16 N17 N19 K7 P8 P9 M9 P11 P13 P16 P17 P18 P12 R8 R9 R11 R12 R13 R17 T8 T9 N7 T11 T12 T13 T14 T15 T16 T17 U8 U9 U10 U11 U12 U13 U14 U15 U16 U17 R18 V9 V10 V11 V12 V14 V17 T7 E8

R298

0

RL_ON

LGE Internal Use Only

+3.5V_ST

OPT

C401

100uF

16V

+12V/+15V

OPT

C402

100uF

16V

+3.5V_ST

R461 10K

OPT

R401

10K

B

R462

10K

MLB-201209-0120P-N2

C406

0.1uF 16V

L402

MLB-201209-0120P-N2

C404

0.1uF 16V

L402-*1

CIS21J121

C

Q401 2SC3052

E

L404

+3.5V_ST

L404-*1

CIS21J121

C407

0.1uF 16V

OPT

FROM LIPS & POWER B/D

RT1P141C-T112

Q402

R406

4.7K

C408

0.1uF 16V

3

1

OPT

R476

0

2

POWER_23_GND

NORMAL_EXPEPT_32

P403

FW20020-24S

PWR ON

24V GND GND

3.5V

3.5V GND GND 12V 12V 12V

GND/P.DIM2

1

1 3

3

3 5

5

5 7

7

7 9

9

9 11

11

11 13

13

13 15

15

15 17

17

17 19

19

19 21

21 22

21 22 23

23 24

25

SLIM_32~52 P401

SMAW200-H24S2

NORMAL_32

P404 FM20020-24

2

2 4

4

4 6

6

6 8

8

10

10 12

12

12 14

14

14 16

16

16 18

18

18 20

20

20 22 24

24V 24V GND GND

3.5V

3.5V GND GND/V-sync INV ON A.DIM P.DIM1 Err OUT

POWER_24_GND

MLB-201209-0120P-N2

POWER_16_GND

R475

0

POWER_24_PWM_DIM

POWER_22_PWM_DIM

L407-*1

CIS21J121

L407

C418

0.1uF 50V

POWER_18_INV_CTL

R415 100

R425 100

R412 0

POWER_24_INV_CTL

OPT

+3.3V_Normal

C

R418

6.8K OPT

E

POWER_20_PWM_DIM

R484

PWM_PULL-DOWN_3.9K

C416

0.1uF

16V

100R437

100

R420

R606

3.9K

0

0R472

0R471

POWER_20_ERROR_OUT

POWER_24_ERROR_OUT

+24V

OPT

C426 68uF 35V

R419 1K

R421 10K

B

Q405

2SC3052

POWER_18_A_DIM

R451

POWER_22_A_DIM

R485 0

POWER_20_A_DIM

R453

+3.5V_ST

R426 10K

10K OPT

0

R606-*1 1K

PWM_PULL-DOWN_1K

+3.3V_Normal

OPT

R486

4.7K

INV_CTL

R427

A_DIM

PWM_DIM

ERROR_OUT

PANEL_CTL

1:AK10

+12V/+15V

L412

R489 10K

+3.5V_ST

0.015uF

R430 10K

R429 47K

OPT

L420 BLM18PG121SN1D

+3.3V_Normal

C461 10uF 10V

0.01uF

C409

C436

0.015uF

0.01uF

50V

25V

R431

OPT

22K

C

Q406

B

2SC3052

OPT

E

+1.5V_DDR

AP7173-SPG-13 HF(DIODES)

IN

PG

VCC

R433

EN

10K

16V

C475

0.1uF

R435

IC407

1

2

3

1.5A

4

OPT

22K

C438

0.1uF 16V

R439

33K

R440

5.6K

B

9

THERMAL

C

Q407 2SC3052

E

8

7

6

5

[EP]

OUT

FB

SS

GND

C442 10uF 16V OPT

C443 10uF

25V

Q409

AO3407A

S

C467 560pF 50V

ST_3.5V--> 3.375V --> 3.46V 20V-->3.51V --> 3.76V (3.59V)

PANEL_POWER

R405-*1

R407-*1

3K

New item

D

G

C451

0.1uF OPT

PANEL_DISCHARGE_RES

C455

0.1uF 16V

3K

PANEL_DISCHARGE_RES

PANEL_VCC

R407

R405

2.2K

OPT

24V-->3.78V --> 3.92V (3.79V) 12V -->3.58V --> 3.82V (3.68V)

18.5V-->3.5V --> 3.75V (3.59V)

C411

0.1uF 16V

+24V

C412

0.1uF 16V

PD_+12V

POWER_+24V

R482

R403

8.2K

1.5K

1%

+12V/+15V

R448

2.7K

R447

1.21K

1%

PD_+12V

1/10W

1%

PD_+12V

+3.5V_ST

R45005%

VCC

+3.5V_ST -> 3.375V

NCP803SN293

PD_+3.5V

VCC

3

R404

PD_+12V

100K

IC409

NCP803SN293

3

2

1

GND

PD_+12V_PWR_DET_ON_SEMI

GND

RESET

R488 100K

IC408

1

RESET

2

PWR_DET_ON_SEMI

PD_+12V

R480 100

+3.5V_ST

R402 100

R463

10K

OPT

POWER_DET

C474

0.1uF

IC408-*1

APX803D29

VCC

PWR_DET_DIODES

VCC

PD_+12V_PWR_DET_DIODES

3

1

GND

IC409-*1

APX803D29

3

1

GND

RESET

2

RESET

2

Power_DET

Max 1000mA

+1.5V_DDR

R457

4.3K

1/16W

R1

1%

R45 6

4.7 K

1/1 6W

R2

C472 22uF 10V

C476

0.1uF 16V

POWER_ON/OFF_1

+3.3V_Normal

+3.5V_ST

0.1uF

C435

16V

R490

R434

10K

OPT

10K

R443 10K

Q403

RSR025P03

S

D

G

C423

R438

4.7uF

22K

16V

R445

2.2K

C

Q400

B

2SC3052

E

780 mA

L403

BLM18PG121SN1D

C425

0.1uF

16V

+3.3V_Normal

R446

C445

10K

0.1uF 16V

OPT

C437 22uF 16V

OPT

GND

CMO10"Lamp

PWM_DIM

INV_ON

32LE5300-TA

NC

err_out

NC

--> NC

PWM_DIM

NC

(PSU)

GND

A-DIM

NC

GND

CMO10"LED

(PSU)

NC

INV_ON

NC

AUO 10"Lamp

(PSU)

GND

INV_ON

Err_out

NC

PWM_DIM

GND

32LE4500-TA

AUO 10"LED

(PSU)

NC

INV_ON

err_out

--> NC NC

PWM_DIM

NC

SHARP (PSU)

INV_ON

52/60:ERROR

26/32HD:NC 26/32/52:PWM

26/32/52:GND

32LE5300-TA

LGD 10"LED

INV_ON

PWM_DIM err_out

--> NC

PIN No

LGD(PSU)

or LIPS

16

INV_ON

18

VBR-A

20

22

PWM_DIM

Err_out

24

23

<LED MODULE PIN MAP -> latest update 20100618>

PIN No

LGD LPB/

OS LPB

16

INV_ON

18

20

PWM_DIM

22

err_out

24

--> NC

23

60:PWM

(PSU)

GND

60:NC

GND

IPS-@ (PSU)

INV_ON

Err_out

PWM_DIM

GND

NC

LGD edge led error-out use or not? checking is necessary...

+12V/+15V

+5V_USB

L401

C405 10uF 25V

R416 56K

1%

R1

C489 100pF

R2

R607 11K

R423

R410

10K

1%

12K

1%

C494 1uF 10V

C493 3300pF 50V

Vout=(1+R1/R2)*0.765=5.03V

TPS54327DDAR

EN

VFB

VREG5

SS

IC401

1

2

3A

3

4

9

THERMAL

8

7

6

5

[EP]GND

VIN

VBST

SW

GND

C413

0.1uF

50V

L406

3.6uH

NR8040T3R6N

GND

Vout=0.8*(1+R1/R2)=1.5319

+5V_Normal

+5V_TUNER

OUTIN

+5V_TUNER

330 R409

+5V_TUNER

TP401

MAX 1A

R465

24K

+5V_TUNER

1%

51K

R466

OPT C427 100pF

R467

10K

110

R408

1%

C471 22uF 16V

+5V_TUNER

R424

1

5%

C417

0.1uF 16V

+5V_TUNER

C477

0.1uF 16V

C419 10uF 10V

R1

50V

1%

R2

+12V/+15V

+2.5V/+1.8V

+3.3V_Normal

NC

C432

0.1uF 16V

VIN

IC402

TJ3940S-2.5V-3L

3

Vd=550mV

1

GND

+2.5V_Normal

VOUT

2

1

R473

C403

C440

10uF

0.1uF

10V

16V

300 mA

INV <--> MAIN

L417

+5V_TUNER

C458 10uF 25V

+5V_TUNER

C460 10uF 25V

+5V_TUNER

Vout=0.8*(1+R1/R2)

C490

0.1uF 16V

+5V_TUNER

AOZ1072AI-3

PGND

1

VIN

2

AGND

3

FB

4

IC406

+5V_TUNER

2A

L422

+5V_TUNER

R459

10K

+5V_TUNER

12K

R458

3.6uH

NR8040T3R6N

+5V_TUNER

2200pF

C466

LX_2

8

LX_1

7

EN

6

COMP

5

#11 <--> #24 #12 <--> #18 #13 <--> #20 #14 <--> #22

+5V_Normal

L424

BLM18PG121SN1D

R422 1

+5V_TUNER

5%

+5V_TUNER

C414

C415

0.1uF

10uF 10V

16V +5V_TUNER

+3.3V_Normal

OLP

Not used : only for small(ready)

R180 10K OPT R181

1K

OPT

C422

0.1uF 50V

+5V_TUNER

IC411

AP1117EG-13

+5V_TUNER

ADJ/GND

2000 mA

C420 22uF 16V

C492 22uF 16V

OPT

+5V_USB

+5V_Normal

L425

BLM18PG121SN1D

NON_5V_TUNER

+3.5V_ST

L413

C430 10uF 10V

+3.3V_Normal

C431

0.1uF 16V

S7LR core 1.2V volt

10K

VIN_3

EP[GND]

1

THERMAL

2

3

TPS54319TRE

4

5

AGND

4A

15EN16

17

IC403

6

VSENSE

C447

0.1uF 16V

7

COMP

BOOT14PWRGD

13

12

11

10

9

8

RT/CLK

$ 0.165

PH_3

PH_2

PH_1

SS/TR

R436 15K

C441

0.1uF

16V

R432

330K1/16W 5%

C488

3300pF

C448

3300pF

NR8040T3R6N

50V

L415

3.6uH

C453 22uF

10V

C456 22uF 10V

R1

R2

R428

VIN_1

VIN_2

GND_1

GND_2

IC410

AP1117EG-13

+5V_TUNER

OUTIN

ADJ/GND

C491

+5V_TUNER

0.1uF 50V

+1.10V_VDDC

C444

0.1uF

50V 100pF C439

16V

OPT R400

0

FB_CORE

0

R608

1%

27K

R44 2

1/1 6W

1%

56K

R44 1

1/1 6W

C421,C422 Close to LDO

330 R411

+5V_TUNER

110

R417

+5V_TUNER

Vout=0.827*(1+R1/R2)=1.225V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

20110324

POWER_LARGE 4

CONTROL

LGE Internal Use Only

IR & LED

+3.5V_ST

R2405

R2404

10K

1%

R2429

Q2405

2SC3052

OPT

L2401

BLM18PG121SN1D

L2402

BLM18PG121SN1D

+3.5V_ST

47K OPT

C

B

E

R2431

47K

OPT

R2426

+3.5V_ST

47K

S/T_SCL

S/T_SDA

+3.5V_ST

C2401

0.1uF

C2402

0.1uF

L2403

BLM18PG121SN1D

C2403

0.1uF 16V

D2401

5.6V

AMOTECH

D2402

AMOTECH

C2404 1000pF 50V

+3.3V_Normal

C906 18pF 50V

OPT

C907 18pF 50V

OPT

5.6V

LED_B/LG_LOGO

L2404

BLM18PG121SN1D

C2405

0.1uF

NEW_SUB

D902

CDS3C05HDMI1

5.6V

NEW_SUB

D903

CDS3C05HDMI1

5.6V

16V

R2401 100

KEY1

R2402 100

KEY2

+3.5V_ST

R2425

Q2406

2SC3052

47K OPT

R2430

C

10K

B

E

OPT

R2427 0

R2428

IR

22

SENSOR_SCL

SENSOR_SDA

C2406

1000pF

50V

EYEQ/TOUCH_KEY

R2412

R2413 1.5K

C2407 100pF

LED_R/BUZZ

R2411 100

100

50V

C2408 18pF 50V

OPT

C2409 18pF 50V

OPT

C2410

0.1uF

D2405

5.6V

R2414

1.5K

OPT

16V

EYEQ/TOUCH_KEY

5.6V D2403

EYEQ/TOUCH_KEY

5.6V D2404

JP2407

JP2408

OPT

R2416

10K

OLD_SUB

P2401

12507WR-12L

1

2

3

4

5

6

7

JP2409

JP2410

JP2411

8

9

10

11

12

13

NEW_SUB

P2402

12507WR-15L

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

IR/CONTROL-L

20110324

6

USB_JACK_LV3400

LGE Internal Use Only

JK1450-*1

1234

USB DOWN STREAM

3AU04S-345-ZC-H-LG

5

USB_DIODES

R1458 2K 1/8W 1%

USB_JACK

JK1450

1234

USB DOWN STR EAM

3AU 04S-3 05-Z C-(LG )

5

L1451-*1

CIS21J121

L1451

MLB-201209-0120P-N2

120-ohm

R1459 2K

C1451 1/8W 1%

22uF

16V

D1451 RCLAMP0502BA

OPT

OUT_2

OUT_1

NC

FLG

EAN61849601

IC1450

AP2191DSG

8

$0.077

7

6

5

R1451 47

GND

1

IN_1

2

IN_2

3

EN

4

SIDE_USB_DM

SIDE_USB_DP

R1454 10K

C1452 10uF 10V

USB1_OCD

C1453

0.1uF

+5V_USB

+3.3V_Normal

R1455

4.7K

OPT

USB1_CTL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

20101023GP2R

USB_OCP_DIODE 7

HDMI_1

LGE Internal Use Only

SHIELD

HDMI_1

EAG59023302

JK802

HDMI EEPROM

5V_HDMI_1

+5V_Normal

A1CA2 ENKMC2838-T112

R874

10K

R884

2.7K

5V_HDMI_2

10K

R873

R885

2.7K

D821

R888

2.7K

+5V_Normal

A1CA2 ENKMC2838-T112 D822

R889

2.7K

EDID_WP

DDC_SCL_1

DDC_SDA_1

EDID_WP

DDC_SCL_2

DDC_SDA_2

5V_HDMI_1

20

19

18

17

16

15

14

13

12

11

CK+

10

D0-

9

D0_GND

8

D0+

7

D1-

6

D1_GND

5

D1+

4

D2-

3

D2_GND

2

D2+

1

R896 1K

R804

1.8K

OPT

D802

5V_DET_HDMI_1

3.3K

R802

C802

0.1uF 16V

R805

OPT

R824

R806

10K

C

Q802

2SC3052

0

R830

B

10K

E

HPD1

DDC_SDA_1

DDC_SCL_1

HDMI_ARC

HDMI_CEC

CK-_HDMI1

CK+_HDMI1

D0-_HDMI1

D0+_HDMI1

D1-_HDMI1

D1+_HDMI1

D2-_HDMI1

D2+_HDMI1

HDMI_1_RENESAS

IC801-*1

R1EX24002ASAS0A

A0

1

A1

2

A2

3

VSS

4

HDMI_2_RENESAS

IC802-*1

R1EX24002ASAS0A

A0

1

A1

2

A2

3

VSS

4

VCC

8

WP

7

SCL

6

SDA

5

VCC

8

WP

7

SCL

6

SDA

5

HDMI_1_ATMEL

AT24C02BN-SH-T

A0

1

A1

2

A2

3

GND

4

AT24C02BN-SH-T

A0

1

A1

2

A2

3

GND

4

IC801

$0.055

HDMI_2_ATMEL

IC802

$0.055

VCC

8

WP

7

SCL

6

R876 22

SDA

5

R875 22

VCC

8

WP

7

6

5

JP810

SCL

SDA

C806

0.1uF

R878 22

R877 22

C807

HDMI_1_EEPROM

HDMI_2_EEPROM

HDMI_2

SHIELD

20

HDMI_2

EAG59023302

JK801

5V_HDMI_2

R895

19

18

17

16

15

14

13

12

11

CK+

10

D0-

9

D0_GND

8

D0+

7

D1-

6

D1_GND

5

D1+

4

D2-

3

D2_GND

2

D2+

1

1K

R803

1.8K

5V_DET_HDMI_2

C801

0.1uF 16V

R801

3.3K

R815 0

OPT

D801

R807

10K

Q801

2SC3052

C

R828

10K

B

E

HPD2

DDC_SDA_2

DDC_SCL_2

HDMI_CEC

CK-_HDMI2

CK+_HDMI2

D0-_HDMI2

D0+_HDMI2

D1-_HDMI2

D1+_HDMI2

D2-_HDMI2

D2+_HDMI2

SIDE_HDMI

BODY_SHIELD

20

19

18

17

16

15

14

13

12

11 10

EAG62611201

HDMI_SIDE

JK803

5V_HDMI_4

R897

1K R837

1.8K

CK+

D0-

9

D0_GND

8

D0+

7

D1-

6

D1_GND

5

D1+

4

D2-

3

D2_GND

2

D2+

1

5V_DET_HDMI_4

C803

0.1uF 16V

3.3K

JP805

JP806

R841

R835

OPT

D811

R808

10K

C

Q803

2SC3052

0

R862

B

10K

E

HPD4

DDC_SDA_4

DDC_SCL_4

HDMI_CEC

CK-_HDMI4

CK+_HDMI4

D0-_HDMI4

D0+_HDMI4

D1-_HDMI4

D1+_HDMI4

D2-_HDMI4

D2+_HDMI4

HDMI_SIDE_RENESAS

IC804-*1

R1EX24002ASAS0A

A0

1

A1

2

A2

3

VSS

4

VCC

8

WP

7

SCL

6

SDA

5

For CEC

HDMI_CEC

OPT

D803

AVRL161A1R1NT

GND

HDMI_SIDE_ATMEL

AT24C02BN-SH-T

A0

1

A1

2

A2

3

GND

4

OPT

D804

IC804

$0.055

VCC

8

WP

7

SCL

6

SDA

5

OPT 68K

R854

S

R855 100

OPT

G

C809

0.1uF

JP812

R881 22

R882 22

+3.5V_ST

OPT

D

Q806

SI1012CR-T1-GE3

GND

+5V_Normal

5V_HDMI_4

10K

R871

HDMI_SIDE_EEPROM

R887

R891

2.7K

R856 10K

C805

0.1uF 16V

OPT

A1CA2 ENKMC2838-T112 D824

R857 68K OPT

EDID_WP

DDC_SCL_4

DDC_SDA_4

CEC_REMOTE_S7

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

20110324 GP3_S7LR

HDMI 8

RGB/SPDIF/PC/HP

LGE Internal Use Only

New Item Development

EARPHONE BLOCK

HP_LOUT

002:V7

HP_ROUT

002:V7

C1118 10uF 16V

C1119 10uF 16V

C1115 1000pF 50V

OPT

C1116 1000pF 50V

OPT

R1125 1K

R1128

1K

Q1101

MMBT3904-(F)

Q1102

MMBT3904-(F)

C

B

E

C

B

E

MMBT3904-(F)

B

MMBT3904-(F)

B

E

C

E

C

Q1104

Q1103

HP_DET

+3.3V_Normal

R1130

10K

R1155 1K

HEAD_PHONE

JK3301

KJA-PH-0-0177

5GND

4L

3DETECT

1R

C

Q1105

ISA1530AC1

E

B

R1129

3.3K

+3.5V_ST

C

E

B Q1106

2SC3052

SIDE_HP_MUTE

PC AUDIO

JK1102

PEJ027-04

E_SPRING

3

T_TERMINAL1

6A

B_TERMINAL1

7A

R_SPRING

4

T_SPRING

5

B_TERMINAL2

7B

T_TERMINAL2

6B

D1101 AMOTECH

5.6V OPT

D1102

AMOTECH

5.6V OPT

C1107

100pF

50V

C1108 100pF 50V

R1102 470K

R1103 470K

R1107 15K

R1108 15K

R1110 10K

R1111

10K

PC_R_IN

PC_L_IN

002:S12

SPDIF OPTIC JACK

5.15 Mstar Circuit Application

SPDIF_OUT

002:T18

R1104

10K OPT

C1109 22uF 16V

OPT

C1110 10uF 16V

OPT

+3.3V_Normal

C1131

0.1uF 16V

C1121 100pF 50V

JK1103

2F01TC1-CLM97-4F

GND

1

VCC

2

VIN

3

Fib er Op tic

4

SHI ELD

RGB PC

RGB_EEMPROM_RENESAS

R1EX24002ASAS0A

A0

A1

A2

VSS

DSUB_VSYNC

DSUB_HSYNC

DSUB_B+

DSUB_G+

DSUB_R+

IC1105-*1

1

2

3

4

D1116

5.6V OPT

+5V_Normal

EDID_WP

RGB_DDC_SCL

RGB_DDC_SDA

+3.3V_Normal

R1146 10K

D1117

5.6V

OPT

R1147 1K

DSUB_DET

D1115

ENKMC2838-T112

A1

C

A2

RGB_EEMPROM_ATMEL

IC1105

AT24C02BN-SH-T

VCC

8

1

WP

7

2

SCL

6

3

SDA

4

5

R1133 75

R1135 75

R1137 75

GND

C1122 68pF 50V OPT

A0

A1

A2

VCC

8

WP

7

SCL

6

SDA

5

D1109 30V

D1110 30V

D1111 30V

D1112 30V

C1127

18pF

R1139

2.2K

C1128 18pF

50V

C1126 68pF 50V OPT

D1113

30V

R1140

2.2K

RGB_EEPORM

R1141 22

D1114

5.6V OPT

R1142

10K

C1129

0.1uF 16V

R1143 22

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

RED2GREEN3BLUE4GND_15DDC_GND

RED_GND7GREEN_GND8BLUE_GND9NC10SYNC_GND

GND_212DDC_DATA13H_SYNC14V_SYNC15DDC_CLOCK

JK1104

SPG09-DB-010

11

6

1

16

SHILED

RGB/SPDIF/HP 9

20110324GP3_S7LR

RS232C

LGE Internal Use Only

C1101 0.33uF

C1102

0.1uF

C1103

0.1uF

C1104

0.1uF

C1105

0.1uF DOUT2

RIN2

C1+

C1-

C2+

C2-

V+

V-

IC1101 MAX3232CDR

1

2

3

4

5

6

7

8

EAN41348201

10

5

9

4

R1123 100

+3.5V_ST

D1107 CDS3C30GTH 30V

OPT

C1106

0.1uF

VCC

16

GND

15

DOUT1

14

RIN1

13

ROUT1

12

DIN1

11

DIN2

10

ROUT2

9

D1108 CDS3C30GTH 30V

OPT

PM_RXD

PM_TXD

R1124 100

JP1111

JP1112

8

7

6

SPG09-DB-009

JK1101

3

2

1

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

20110324GP3_S7LR

RS232C_9PIN 10

[51Pin LVDS Connector]

LGE Internal Use Only

(For FHD 60/120Hz)

P703

FI-RE51S-HF-J-R1500

WAFER_FHD

52

PANEL_VCC

L702 120-ohm WAFER_FHD

C700

C709 1000pF 50V

OPT

RXA4-

RXA4+

RXA3-

RXA3+

BIT_SEL

C710

0.1uF 16V

WAFER_FHD

R709 10K

BIT_SEL_LOW

LVDS_SEL

+3.3V_Normal

R705

3.3K OPT

R710 10K

OPT

10uF 16V

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

OPT

RXACK-

RXACK+

RXA2-

RXA2+

RXA1-

RXA1+

RXA0-

RXA0+

RXB4-

RXB4+

RXB3-

RXB3+

RXBCK-

RXBCK+

RXB2-

RXB2+

RXB1-

RXB1+

RXB0-

RXB0+

[30Pin LVDS Connector] (For HD 60Hz_Normal)

P705

FF10001-30

HD

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

OPT

R7130

RXA3-

RXA3+

RXACK-

RXACK+

RXA2-

RXA2+

RXA1-

RXA1+

RXA0-

RXA0+

LVDS_SEL

+3.3V_Normal

R712

3.3K

R711 10K

C701 10uF 16V

OPT

C702 1000pF 50V

PANEL_VCC

L701

120-ohm

HD

C703

0.1uF 16V

HD

OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

20110324GP3_S7LR

LVDS_LARGE 11

AVDD_DDR0

LGE Internal Use Only

R1201

R1202

1K 1%

0.1uF

1K 1%

C1201

A-MVREFDQ

1000pF

C1202

AVDD_DDR0

R1204

R1205

1K 1%

0.1uF

1K 1%

C1203

A-MVREFCA

1000pF

C1204

BLM18PG121SN1D

+1.5V_DDR

L1202

OPT

C1251

AVDD_DDR0

10uF

C1205

DDR3 1.5V By CAP - Place these Caps near Memory

10uF

C1206

0.1uF

C1207

0.1uF

C1208

0.1uF

C1210

0.1uF

C1211

Close to DDR Power Pin

CLose to Saturn7M IC

N3

A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

M7

NC_5

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

A-MA0 A-MA1 A-MA2 A-MA3 A-MA4 A-MA5 A-MA6 A-MA7 A-MA8 A-MA9 A-MA10 A-MA11 A-MA12 A-MA13

A-MBA0 A-MBA1 A-MBA2

A-MCKE

A-MODT A-MRASB A-MCASB A-MWEB

A-MRESETB

A-MDQSL A-MDQSLB

A-MDQSU A-MDQSUB

A-MDML A-MDMU

A-MDQL0 A-MDQL1 A-MDQL2 A-MDQL3 A-MDQL4 A-MDQL5 A-MDQL6 A-MDQL7

A-MDQU0 A-MDQU1 A-MDQU2 A-MDQU3 A-MDQU4 A-MDQU5 A-MDQU6 A-MDQU7

R1235

56

R1236

56

R1231 10K

A-MCK

1%

C1209

0.01uF

1%

25V

A-MCKB

AVDD_DDR0

A-MRESETB

A-MVREFCA

A-MVREFDQ

AVDD_DDR0

A-MA14

240

1%

R1203

CLose to DDR3

H5TQ1G63DFR-H9C

M8

VREFCA

H1

VREFDQ

L8

ZQ

B2

VDD_1

D9

VDD_2

G7

VDD_3

K2

VDD_4

K8

VDD_5

N1

VDD_6

N9

VDD_7

R1

VDD_8

R9

VDD_9

A1

VDDQ_1

A8

VDDQ_2

C1

VDDQ_3

C9

VDDQ_4

D2

VDDQ_5

E9

VDDQ_6

F1

VDDQ_7

H2

VDDQ_8

H9

VDDQ_9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

T7

NC_6

A9

VSS_1

B3

VSS_2

E1

VSS_3

G8

VSS_4

J2

VSS_5

J8

VSS_6

M1

VSS_7

M9

VSS_8

P1

VSS_9

P9

VSS_10

T1

VSS_11

T9

VSS_12

B1

VSSQ_1

B9

VSSQ_2

D1

VSSQ_3

D8

VSSQ_4

E2

VSSQ_5

E8

VSSQ_6

F9

VSSQ_7

G1

VSSQ_8

G9

VSSQ_9

EAN61828901

IC1201

DDR_1333_HYNIX

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

0.1uF

C1212

A-MA0

A-MA1 A-MA2 A-MA3 A-MA4 A-MA5

A-MA6

A-MA7 A-MA8

A-MA9 A-MA10 A-MA11 A-MA12 A-MA13

A-MA14

A-MBA0 A-MBA1 A-MBA2

A-MCK

A-MCKB A-MCKE

A-MODT A-MRASB A-MCASB

A-MWEB

A-MDQSL

A-MDQSLB

A-MDQSU

A-MDQSUB

A-MDML

A-MDMU

A-MDQL0

A-MDQL1 A-MDQL2 A-MDQL3 A-MDQL4 A-MDQL5 A-MDQL6 A-MDQL7

A-MDQU0 A-MDQU1 A-MDQU2 A-MDQU3 A-MDQU4 A-MDQU5 A-MDQU6 A-MDQU7

0.1uF

C1213

0.1uF

C1216

0.1uF

C1215

C1214

A11 C14 B11 F12 C15 E12 A14 D11 B14 D12 C16 C13 A15 E11 B13

F13 B15 E13

C17 A17 B16

E14 B12 A12 C12

F11

B19 C18

B18 A18

E15 A21

D17 G15 B21 F15 B22 F14 A22 D15

G16 B20 F16 C21 E16 A20 D16 C20

C1217

S7LR_DIVX_MS10

A_DDR3_A[0] A_DDR3_A[1] A_DDR3_A[2] A_DDR3_A[3] A_DDR3_A[4] A_DDR3_A[5] A_DDR3_A[6] A_DDR3_A[7] A_DDR3_A[8] A_DDR3_A[9] A_DDR3_A[10] A_DDR3_A[11] A_DDR3_A[12] A_DDR3_A[13] A_DDR3_A[14]

A_DDR3_BA[0] A_DDR3_BA[1] A_DDR3_BA[2]

A_DDR3_MCLK A_DDR3_MCLKZ A_DDR3_MCLKE

A_DDR3_ODT A_DDR3_RASZ A_DDR3_CASZ A_DDR3_WEZ

A_DDR3_RESET

A_DDR3_DQSL A_DDR3_DQSLB

A_DDR3_DQSU A_DDR3_DQSUB

A_DDR3_DQML A_DDR3_DQMU

A_DDR3_DQL[0] A_DDR3_DQL[1] A_DDR3_DQL[2] A_DDR3_DQL[3] A_DDR3_DQL[4] A_DDR3_DQL[5] A_DDR3_DQL[6] A_DDR3_DQL[7]

A_DDR3_DQU[0] A_DDR3_DQU[1] A_DDR3_DQU[2] A_DDR3_DQU[3] A_DDR3_DQU[4] A_DDR3_DQU[5] A_DDR3_DQU[6] A_DDR3_DQU[7]

0.1uF

C1218

C1219

IC101

LGE2112-T8

0.1uF

C1220

0.1uF

C1221

0.1uF

C1223

C1222

B_DDR3_A[0] B_DDR3_A[1] B_DDR3_A[2] B_DDR3_A[3] B_DDR3_A[4] B_DDR3_A[5] B_DDR3_A[6] B_DDR3_A[7] B_DDR3_A[8]

B_DDR3_A[9] B_DDR3_A[10] B_DDR3_A[11] B_DDR3_A[12] B_DDR3_A[13] B_DDR3_A[14]

B_DDR3_BA[0] B_DDR3_BA[1] B_DDR3_BA[2]

B_DDR3_MCLK B_DDR3_MCLKZ B_DDR3_MCLKE

B_DDR3_ODT B_DDR3_RASZ B_DDR3_CASZ

B_DDR3_WEZ

B_DDR3_RESET

B_DDR3_DQSL

B_DDR3_DQSLB

B_DDR3_DQSU

B_DDR3_DQSUB

B_DDR3_DQML B_DDR3_DQMU

B_DDR3_DQL[0] B_DDR3_DQL[1] B_DDR3_DQL[2] B_DDR3_DQL[3] B_DDR3_DQL[4] B_DDR3_DQL[5] B_DDR3_DQL[6] B_DDR3_DQL[7]

B_DDR3_DQU[0] B_DDR3_DQU[1] B_DDR3_DQU[2] B_DDR3_DQU[3] B_DDR3_DQU[4] B_DDR3_DQU[5] B_DDR3_DQU[6] B_DDR3_DQU[7]

0.1uF

C1224

0.1uF

B23 D25 F22 G22 E24 F21 E23 D22 D24 D21 C24 C25 F23 E21 D23

G20 F24 F20

G25 G23 F25

D20 B25 B24 A24

E20

K24 K25

J21 J20

H24 L20

L23 J24 L24 J23 M24 H23 M23 K23

G21 L22 H22 K20 H20 L21 H21 K21

0.1uF

DDR3 1.5V By CAP - Place these Caps near Memory

0.1uF

C1227

B-MA0 B-MA1 B-MA2 B-MA3 B-MA4 B-MA5 B-MA6 B-MA7 B-MA8 B-MA9 B-MA10 B-MA11 B-MA12 B-MA13 B-MA14

B-MBA0 B-MBA1 B-MBA2

B-MCK B-MCKB B-MCKE

B-MODT B-MRASB B-MCASB B-MWEB

B-MRESETB

B-MDQSL B-MDQSLB

B-MDQSU B-MDQSUB

B-MDML B-MDMU

B-MDQL0 B-MDQL1 B-MDQL2 B-MDQL3 B-MDQL4 B-MDQL5 B-MDQL6 B-MDQL7

B-MDQU0 B-MDQU1 B-MDQU2 B-MDQU3 B-MDQU4 B-MDQU5 B-MDQU6 B-MDQU7

C1228

0.1uF

C1229

C1230

0.1uF

C1231

0.1uF

C1232

0.1uF

C1233

0.1uF

C1234

0.1uF

C1235

0.1uF

C1236

0.1uF

C1237

B-MCKB

0.1uF

C1241

C1239

C1238

Close to DDR Power Pin

B-MA10 B-MA11 B-MA12 B-MA13

B-MCK

AVDD_DDR1

C1240

0.01uF 25V

R1232

10K

56

1%

56

1%

B-MODT B-MRASB B-MCASB

B-MWEB

B-MRESETB

B-MDQSL

B-MDQSLB

B-MDQSU

B-MDQSUB

B-MDML

B-MDMU

B-MDQL0 B-MDQL1 B-MDQL2 B-MDQL3 B-MDQL4 B-MDQL5 B-MDQL6 B-MDQL7

B-MDQU0 B-MDQU1 B-MDQU2 B-MDQU3 B-MDQU4 B-MDQU5 B-MDQU6 B-MDQU7

0.1uF

B-MA0 B-MA1 B-MA2 B-MA3 B-MA4 B-MA5 B-MA6 B-MA7 B-MA8 B-MA9

R1237

B-MCKE

R1238

C1242

B-MBA0 B-MBA1 B-MBA2

0.1uF

C1243

DDR_DVB_T2_2G

N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

M7

M2 N8 M3

J7 K7 K9

L2 K1 J3 K3 L3

T2

F3 G3

C7 B7

E7 D3

E3 F7 F2 F8 H3 H8 G2 H7

D7 C3 C8 C2 A7 A2 B8 A3

0.1uF

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13

NC_5

BA0 BA1 BA2

CK CK CKE

CS ODT RAS CAS WE

RESET

DQSL DQSL

DQSU DQSU

DML DMU

DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7

DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7

C1244

IC1201-*3

K4B2G1646C

0.1uF

VREFCA

VREFDQ

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

C1245

N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

M7

M2 N8 M3

J7 K7 K9

L2 K1 J3 K3 L3

T2

F3 G3

C7 B7

E7 D3

E3 F7 F2 F8 H3 H8 G2 H7

D7 C3 C8 C2 A7 A2 B8 A3

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

NC_1 NC_2 NC_3 NC_4 NC_6

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9

AVDD_DDR1

BLM18PG121SN1D

C1246

10uF

EAN61828901

IC1202

H5TQ1G63DFR-H9C

DDR_1333_HYNIX

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13

NC_5

BA0 BA1 BA2

CK CK CKE

CS ODT RAS CAS WE

RESET

DQSL DQSL

DQSU DQSU

DML DMU

DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7

DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7

DDR_DVB_T2_2G

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1 J9 L1 L9 T7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

N3 P7 P3 N2 P8 P2 R8 R2 T8 R3 L7 R7 N7 T3

M7

M2 N8 M3

J7 K7 K9

L2 K1 J3 K3 L3

T2

F3 G3

C7 B7

E7 D3

E3 F7 F2 F8 H3 H8 G2 H7

D7 C3 C8 C2 A7 A2 B8 A3

OPT

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12/BC A13

NC_5

BA0 BA1 BA2

CK CK CKE

CS ODT RAS CAS WE

RESET

DQSL DQSL

DQSU DQSU

DML DMU

DQL0 DQL1 DQL2 DQL3 DQL4 DQL5 DQL6 DQL7

DQU0 DQU1 DQU2 DQU3 DQU4 DQU5 DQU6 DQU7

L1203

C1252 10uF 10V

IC1202-*3

K4B2G1646C

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

NC_1 NC_2 NC_3 NC_4 NC_6

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

+1.5V_DDR

ZQ

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

T7

NC_6

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

M8

H1

L8

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1 J9 L1 L9 T7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

B-MVREFCA

CLose to Saturn7M IC

B-MVREFCA

B-MVREFDQ

R1226

240

1%

AVDD_DDR1

B-MA14

GP3_S7LR

DDR_256

0.1uF

1000pF

C1247

IC1201-*1

K4B1G1646G-BCH9

DDR_1333_SS_NEW

N3

A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

M7

NC_5

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

IC1201-*2

NT5CB64M16DP-CF

DDR_1333_NANYA_NEW

N3

EAN61857201A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12

T3

NC_6

M7

NC_5

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

AVDD_DDR1

1K 1%

C1248

R1224

R1225

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

NC_1 NC_2 NC_3 NC_4 NC_6

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

NC_1 NC_2 NC_3 NC_4 NC_7

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1 J9 L1 L9 T7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

ZQ

B-MVREFDQ

M8

H1

L8

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1 J9 L1 L9 T7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

1000pF

CLose to DDR3

IC1202-*1

K4B1G1646G-BCH9

DDR_1333_SS_NEW

N3

A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12/BC

T3

A13

M7

NC_5

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

IC1202-*2

NT5CB64M16DP-CF

DDR_1333_NANYA_NEW

N3

EAN61857201A0

P7

A1

P3

A2

N2

A3

P8

A4

P2

A5

R8

A6

R2

A7

T8

A8

R3

A9

L7

A10/AP

R7

A11

N7

A12

T3

NC_6

M7

NC_5

M2

BA0

N8

BA1

M3

BA2

J7

CK

K7

CK

K9

CKE

L2

CS

K1

ODT

J3

RAS

K3

CAS

L3

WE

T2

RESET

F3

DQSL

G3

DQSL

C7

DQSU

B7

DQSU

E7

DML

D3

DMU

E3

DQL0

F7

DQL1

F2

DQL2

F8

DQL3

H3

DQL4

H8

DQL5

G2

DQL6

H7

DQL7

D7

DQU0

C3

DQU1

C8

DQU2

C2

DQU3

A7

DQU4

A2

DQU5

B8

DQU6

A3

DQU7

20110511

12

C1249

AVDD_DDR1

0.1uF

C1250

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

NC_1 NC_2 NC_3 NC_4 NC_6

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

VREFCA

VREFDQ

VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9

VDDQ_1 VDDQ_2 VDDQ_3 VDDQ_4 VDDQ_5 VDDQ_6 VDDQ_7 VDDQ_8 VDDQ_9

VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8

VSS_9 VSS_10 VSS_11 VSS_12

VSSQ_1 VSSQ_2 VSSQ_3 VSSQ_4 VSSQ_5 VSSQ_6 VSSQ_7 VSSQ_8 VSSQ_9

R1227

1K 1%

R1228

1K 1%

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1 J9 L1 L9 T7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

M8

H1

L8

ZQ

B2 D9 G7 K2 K8 N1 N9 R1 R9

A1 A8 C1 C9 D2 E9 F1 H2 H9

J1

NC_1

J9

NC_2

L1

NC_3

L9

NC_4

T7

NC_7

A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9

B1 B9 D1 D8 E2 E8 F9 G1 G9

/FLASH_WP

LGE Internal Use Only

R1401

OPT

8

7

6

5

8

7

6

5

VCC

HOLD#

SCLK

SI/SIO0

VCC

HOLD[IO3]

CLK

DI[IO0]

+3.5V_ST

R1405 33

C1401

0.1uF

SPI_SCK

SPI_SDI

+3.5V_ST

S_FLASH_MAIN_MACRONIX

OPT

R1404

+3.5V_ST

/SPI_CS

R1403

10K

SPI_SDO

OPT

C

Q1401

B

KRC103S

0

OPT

E

4.7K

DO[IO1]

%WP[IO2]

IC1401

MX25L8006EM2I-12G

CS#

1

SO/SIO1

2

WP#

3

GND

4

S_FLASH_MAIN_WINBOND

IC1401-*1

W25Q80BVSSIG

CS

1

2

3

GND

4

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

SFLASH

20110324

13

GP4R_GLOBAL_TUNER_BLOCK

LGE Internal Use Only

TU3702 TDTJ-S001D

TU3700

DVB_1INPUT_H_LGIT

TDSS-G101D

SI2176_DVB_1INPUT_H

NC

1

RESET

2

SCL

3

SDA

4

+3.3V

5

SIF

6

+1.8V

7

CVBS

8

IF_AGC

9

DIF[P]

10

DIF[N]

11

12

SHIELD

19

SHIELD

TUNER MULTI-OPTION

TU3702-*4

GP2R_AU_1INPUT_H_LGIT

19

SHIELD

TU3702-*1 TDVJ-H101F

ANT_PWR[OPT]

1

BST_CNTL

2

+B

3

NC[RF_AGC]

4

AS

5

SCL

6

SDA

7

NC(IF_TP)

8

SIF

9

NC

10

VIDEO

11

GND

12

1.2V

13

3.3V

14

RESET

15

IF_AGC_CNTL

16

DIF_1

17

DIF_2

18

19

SHIELD

TDTJ-S101D

ANT_PWR

1

NC_1

2

+B1[5V]

3

RF_AGC

4

MOPLL_AS

5

SCL

6

SDA

7

NC_2

8

SIF

9

NC_3

10

VIDEO

11

GND

12

+B2[1.2V]

13

+B3[3.3V]

14

RESET

15

IF_AGC

16

DIF_1[N]

17

DIF_2[P]

18

TU3702-*3 UDA55AL

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

GP3_ATSC_1INPUT_H_SANYO

19

SHIELD

NC_1

NC_2

+B[+5V]

NC[RF_AGC]

AS

SCL

SDA

NC(IF_TP)

SIF

NC_3

VIDEO

GND

+1.2V

+3.3V

RESET

IF_AGC_CNTL

DIF_1

DIF_2

RF_S/W_CTL

1

BST_CTL

2

+B1[5V]

3

NC_1[RF_AGC]

4

NC_2

5

SCLT

6

SDAT

7

NC_3

8

SIF

9

NC_4

10

VIDEO

11

GND

12

+B2[1.2V]

13

+B3[3.3V]

14

NTSC_2INPUT_H_LGIT

RESET

15

IF/AGC

16

DIF_1[N]

17

DIF_2[P]

18

19

SHIELD

TU3702-*2 TDTR-T036F

TU3700-*1 TDSS-H101F

NC

1

RESET

2

SCL

3

SDA

4

+B1[3.3V]

5

SIF

6

+B2[1.8V]

7

CVBS

8

IF_AGC

9

DIF[P]

10

DIF[N]

11

SI2176_ATSC_1INPUT_H

12

SHIELD

GP3_ATSC_1INPUT_H_LGIT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

TU3701 TDFR-C036D

CN_2INPUT_H_LG3911

ANT_PWR[OPT]

1

BST_CNTL

2

+B

3

NC[RF_AGC]

4

AS

5

SCL

6

SDA

7

NC[IF_TP]

8

SIF

9

NC

10

VIDEO

11

GND

12

1.2V

13

3.3V

14

RESET

15

IF_AGC_CNTL

16

DIF_1

17

DIF_2

18

31

SHIELD

RF_S/W_CNTL

1

BST_CNTL

2

+B1[+5V]

3

NC[RF_AGC]

4

NC_1

5

SCLT

6

SDAT

7

NC_2

8

SIF

9

NC_3

10

VIDEO

11

GND

12

+B2[1.2V]

13

+B3[3.3V]

14

RESET

15

NC_4

16

SCL

17

SDA

18

ERR

19

SYNC

20

VALID

21

MCL

22

D0

23

D1

24

D2

25

D3

26

D4

27

D5

28

D6

29

D7

30

close to TUNER

R3705 0 C3701

0.1uF 16V

R3707

C3706

0.1uF 16V

C3702

0.1uF 16V

C3737 100pF 50V

FULL_NIM

R3702 100

R3701 100

close to IF line

FULL_NIM

RF_SW_OPT

0

OPT

close to TUNER

+1.2V/+1.8V_TU

FULL_NIM

C3738

0.1uF 16V

C3705

100uF 16V

+5V_TU

C3704

C3703

0.1uF

100pF

16V

50V

CN

close to the tuner pin, add,09029

C3707 100pF

C3739

50V

10uF

6.3V

HALF_NIM R3760 0

R3761 0

HALF_NIM

Close to the tuner

RF_SWITCH_CTL

Pull-up can’t be applied because of MODEL_OPT_2

Q3704

2SC3052

OPT

C3731 10uF 10V

OPT

C

B

E

C3728

0.1uF 16V

OPT

+3.3V_TU

C3708

0.1uF 16V

R3724

FULL_NIM

R3730

FULL_NIM

R3731

FULL_NIM

FULL_NIM_CHINA

FULL_NIM_BR

R3725

R3727

FULL_NIM

R3728

FULL_NIM

R3729

FULL_NIM

R3726

FULL_NIM

R3721

FULL_NIM

R3722

FULL_NIM

R3723

Close to the CI Slot

R3706

GPIO must be added.

OPTION : RF AGC

R3754 10K

OPT

FE_AGC_SPEED_CTL IF_AGC_SEL

+3.3V_TU

R3733

R3732

100K

100

C3710

0.1uF

16V

IF_N_MSTAR

IF_P_MSTAR

1. should be guarded by ground

2. No via on both of them

3. Signal Width >= 12mils Signal to Signal Width = 12mils Ground Width >= 24mils

0

FE_TS_SYNC

FE_TS_VAL_ERR

FE_TS_CLK

TU_I2C_NON_FILTER

TUNER_RESET

R3704 100

HALF_NIM

C3716

0.1uF 16V

FE_TS_DATA[0]

FE_TS_DATA[1]

FE_TS_DATA[2]

FE_TS_DATA[3]

FE_TS_DATA[4]

FE_TS_DATA[5]

FE_TS_DATA[6]

FE_TS_DATA[7]

TU_IIC_NON_ATSC_SANYO

TU_I2C_NON_FILTER

33

TU_I2C_NON_FILTER C3713

C3711

18pF

50V

C3711-*1 20pF 50V

TU_I2C_FILTER

R3735-*1

MLG1005SR27JT

should be guarded by ground

FE_TS_DATA[0-7]

R3740-*1 1K

TU_IIC_ATSC_SANYO

33

R3735

R3736

TU_I2C_FILTER

R3736-*1

MLG1005SR27JT

IF_AGC_MAIN

C3712 22pF 50V

FULL_NIM

FULL_NIM_BR

TU3701-*2 TDFR-B036F

RF_S/W_CNTL

1

BST_CNTL

2

+B1[5V]

3

NC_1[RF_AGC]

4

NC_2

5

SCLT

6

SDAT

7

NC_3

8

SIF

9

NC_4

10

VIDEO

11

GND

12

+B2[1.2V]

13

+B3[3.3V]

14

RESET

15

NC_5

16

SCL

17

SDA

18

ERR

19

SYNC

20

VALID

21

MCL

22

D0

23

D1

24

D2

25

D3

26

D4

27

D5

28

D6

29

D7

30

31

SHIELD

+5V_TU

C3709

0.01uF 25V

BOOSTER_OPT

+3.3V_TU

R3740

1.2K

C3742 20pF 50V

C3713-*1 20pF 50V

L3701

BLM18PG121SN1D

BOOSTER_OPT

R3734 0

Q3701 ISA1530AC1

E

B

C

BOOSTER_OPT

TU_IIC_ATSC_SANYO

R3741

1.2K

C3743 20pF 50V TU_I2C_FILTER

FULL_NIM

C3714 22pF 50V

FULL_NIM

BOOSTER_OPT

R3737

2.2K

Q3702

2SC3052

TU_IIC_NON_ATSC_SANYO

R3741-*1 1K

TU_SCL

TU_SDA

+3.3V_TU

R3742

R3744

4.7K

4.7K FULL_NIM

CN_2INPUT_H_ALTO

TU3701-*4 TDFR-C236D

RF_S/W_CNTL

1

BST_CNTL

2

+B1[+5V]

3

NC[RF_AGC]

4

NC_1

5

SCLT

6

SDAT

7

NC_2

8

SIF

9

NC_3

10

VIDEO

11

GND

12

+B2[1.2V]

13

+B3[3.3V]

14

RESET

15

NC_4

16

SCL

17

SDA

18

ERR

19

SYNC

20

VALID

21

MCL

22

D0

23

D1

24

D2

25

D3

26

D4

27

D5

28

D6

29

D7

30

31

SHIELD

BOOSTER_OPT

R3743 10K

C

E

BOOSTER_OPT

BOOSTER : CHINA OPT

BOOSTER_OPT

R3745 10K

B

NON_BUFFER

R3773 0

R3749 0

DEMOD_SCL

DEMOD_SDA

200mA

FE_BOOSTER_CTL LNA2_CTL

The pull-up/down of LNA2_CTL is depended on MODLE_OPT_1. GPIO must be added for FE_BOOSTER_CTL

+3.3V_TU

+3.3V_BUFFER

R3774

0

R3751

R3752

220

BUFFER

R3750

OPT

1K

E

BUFFER

B

Q3703

ISA1530AC1

C

+3.3V_TU

Please, check Multi Item! 10/12

C3717

0.1uF 16V

+5V_Normal

L3704

FULL_NIM_BCD

+5V_TU

Size change,0929

MLB-201209-0120P-N2

+5V_TUNER

C3719

C3724

22uF

0.1uF

10V

16V

+5V_TUNER

location movement,0929

+5V_TU

+5V_BUFFER

R3775

0

220

BUFFER

IC3703-*2

AZ1117BH-1.8TRE1

IN

3

1

ADJ/GND

HALF_NIM_1.8V

IC3703-*1

AP1117EG-13

OUTIN

ADJ/GND

HALF_NIM_1.2V_DIODES

R3771 10K

FULL_NIM_BCD

R3770 10K

FULL_NIM_SEMTEK

R3769 10K

FULL_NIM_BCD

+5V_TUNER

L3702

C3722 22uF 16V +5V_TUNER

GP3_S7LR

+3.3V_BUFFER

NON_BUFFER

R3772 0

R3753

4.7K

TU_CVBS

OUT

2

HALF_NIM_1.2V_BCD

IC3703

AZ1117BH-ADJTRE1

INPUT

3

IC3701

AP2132MP-2.5TRG1

PG

1

FULL_NIM_BCD

EN

2

VIN

3

VCTRL

4

IC3701-*1

SC4215ISTRT

NC_1

1

FULL_NIM_SEMTEK

EN

2

VIN

3

NC_2

4

C3726

0.1uF 16V +5V_TUNER

TUNER_L

BUFFER

2

OUTPUT

THERMAL

+3.3V_TU

R3776

0

R3755

470

B

ADJ/GND

1

HALF_NIM_1.2V

8

9

7

6

5

8

7

6

5

60mA

+5V_TU

+5V_BUFFER

R3777

0

BUFFER

R3758 82

E

BUFFER ISA1530AC1

Q3705

C

DEMOD_RESET

This was being applied to the only china demod, so this has to be deleted in both main and ISDB sheet.

HALF_NIM_1.8V

R3767-*1

0

R2

HALF_NIM_1.2V

R3767

10

R3768

1.2K R1

[EP]

GND

ADJ

VOUT

NC

FULL_NIM_BCD

R3748-*1 10K

FULL_NIM_SEMTEK

R3748

5.1K

R3747

9.1K

FULL_NIM

1005

TU_SIF

+1.2V/+1.8V_TU

HALF_NIM

R3766 1

1/10W

C3740

0.1uF 16V

HALF_NIM

add,0929

R1

FULL_NIM

R2

C3729

0.1uF 16V

C3741 10uF 10V

HALF_NIM

Vo=0.8*(1+R1/R2)

GND

ADJ

VO

NC_3

+3.3V_TU

Size change,0929

L3703

MLB-201209-0120P-N2

C3725

C3723

0.1uF

22uF

16V

10V

20110511

14

R3703

+1.2V/+1.8V_TU

R3764

0

1/10W FULL_NIM

C3730 10uF 10V

FULL_NIM

+3.3V_Normal

C3715

C3727 22uF 10V

380mA

0.1uF 16V

150 OPT

AMP_MUTE

LGE Internal Use Only

+24V

MLB-201209-0120P-N2

C501

0.1uF 50V

L501

+24V_AMP

AUD_LRCH

AUD_LRCK

AUD_SCK

AMP_SDA

AMP_SCL

R520

10K

R501

10K

C502

0.1uF 50V

+3.5V_ST

B

C503 100pF

50V

R503 100

R504 100

R502

10K

C

Q501

2SC3052

E

R506

100

C504 1000pF

50V

R505

3.3K

1000pF

C505

+3.3V_Normal

L502

BLM18PG121SN1D

C514

0.1uF 16V

C508

0.1uF 16V

C509 33pF 50V

10uF

OPT C510

10V

OPT C511 10uF

10V

C512

0.1uF 16V

C513

0.1uF 16V

OPT C506

10uF

10V

C507 33pF 50V

50V

AMP_RESET

AUD_MASTER_CLK

C515 10uF 10V

AGND_PLL AVDD_PLL DVDD_PLL

DGND_PLL

GND_1

DGND DVDD

SDATA

R521 10K

LF

WCK BCK SDA

C516

1000pF

50V

[EP]

1 2 3 4 5 6 7 8 9 10 11 12

GND_IO

CLK_I

VDD_IO

46

47

48

THERMAL

49

NTP-7400L

13

14

15

SCL

/FAULT

MONITOR0

50V

C517

BST1A

/RESET

AD

43

44

45

IC501

16

17

18

BST2B

MONITOR1

MONITOR2

C518

22000pF

50V

22000pF

OUT1A_2

PGND1A

41

42

19

20

PGND2B

OUT2B_1

PVDD1_2

PVDD1_3

OUT1A_1

38

39

40

21

22

23

OUT2B_2

PVDD2_1

PVDD2_2

+24V_AMP

C519

0.1uF 50V

PVDD1_1

37

36 35 34 33 32 31 30 29 28 27 26 25

24

PVDD2_3

C521

0.1uF 50V

OUT1B_2 OUT1B_1 PGND1B BST1B VDR1 VCC_5 GND_2 VDR2 BST2A PGND2A OUT2A_2 OUT2A_1

+24V_AMP

C520

0.1uF 50V

C522

0.1uF 50V

C523 10uF 35V

OPT

R507

3.3 OPT

C525

0.01uF 50V

C524 10uF 35V

C526 22000pF 50V

C527 22000pF 50V

C52 8 1uF 25V

D501

1N4148W

100V

OPT

D502

1N4148W

100V

D503

1N4148W

100V

OPT

D504

1N4148W

100V

R508

R515

12

C530 390pF 50V

C531 390pF 50V

R509

R513

12

R510 12

C532 390pF 50V

C533 390pF 50V

R511 12

C534 1uF 25V

R514

R512

12

OPT

C52 9 1uF 25V

OPT

L505

10.0uH

L506

10.0uH

L503

10.0uH

L504

10.0uH

C535

0.47uF 50V

C536

0.47uF

50V

C537

0.1uF 50V

C538

0.1uF 50V

C539

0.1uF 50V

C540

0.1uF

50V

R516

4.7K

R517

4.7K

R518

4.7K

R519

4.7K

SPK_L+

SPEAKER_L

SPK_L-

SPK_L+

SPK_L-

SPK_R+

SPK_R-

SPK_R+

SPEAKER_R

SPK_R-

WAFER-ANGLE

4

3

2

1

P501

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

NTP7400

20110324

16

Rear AV

LGE Internal Use Only

JK1604

PPJ233-01

REAR_AV

FIX-TER

PPJ-230-01

JK1601

COMPONENT1

11

5C

4C

3C

4B

3A

4A

5A

10

9

8

7

6

5

4

13

[GN]GND

[GN]G

[GN]C_DET

[BL]B

[RD]R

[WH]L_IN

[RD]R_IN

[RD]MONO

[RD]E-LUG

[RD]O-SPRING

[RD]CONTACT

[WH]C-LUG

[YL]CONTACT

[YL]O-SPRING

[YL]E-LUG

L-MONO

0

R4223

COMPONENT1

EU_OPT

22

21

20

19

18

17

16

15

14

13

12

11

10

PSC008-01

JK1602

AV_DET

COM_GND

SYNC_IN

SYNC_OUT

SYNC_GND2

SYNC_GND1

RGB_IO

R_OUT

RGB_GND

R_GND

D2B_OUT

G_OUT

D2B_IN

G_GND

9

ID

8

B_OUT

7

AUDIO_L_IN

6

B_GND

5

AUDIO_GND

4

AUDIO_L_OUT

3

AUDIO_R_IN

2

AUDIO_R_OUT

1

REAR_AV

R4221

0

EU_OPT

D1619

30V

R1654 75

REAR_AV

D1626

5.6V

C1643 47pF 50V REAR_AV

D1625

5.6V

REAR_AV

R1672

470K

REAR_AV

D1624

5.6V OPT

R1671

470K

REAR_AV

D1602

30V

OPT

D1603

30V

OPT

D1604

30V

D1605 30V

D1606

30V

D1607

5.6V NON_EU

D1609

5.6V NON_EU

C1648 220pF 50V

OPT

+3.3V_Normal

C1646

0.1uF 16V

REAR_AV

L1609

120-ohm

REAR_AV

L1610

120-ohm

REAR_AV

D1610 30V

OPT

R1660 10K

REAR_AV

R1604 75

R1605

R1606

R1607 470K

R1608 75

75

470K

R1666

1K

REAR_AV

C1663

330pF

50V

REAR_AV

C1662 330pF 50V

REAR_AV

AV_CVBS_IN

REAR_AV

R1685 10K

R1689

REAR_AV

R1684 10K

D1611

5.6V OPT

12K

EU_OPT R1609 75

REAR_AV

R1688 12K REAR_AV

AV_CVBS_DET

AV_R_IN

AV_L_IN

EU_OPT C1604 47pF 50V

SC1_R+/COMP1_Pr+

SC1_G+/COMP1_Y+

SC1_B+/COMP1_Pb+

Full Scart/ Comp1

D1608

5.6V OPT

D1601

5.6V OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EU_OPT L1601 BLM18PG121SN1D

EU_OPT L1602 BLM18PG121SN1D

+3.3V_Normal

R1613 10K

C1607

0.1uF 16V

L1604

120-ohm

L1603

120-ohm

C1608 220pF 50V OPT

R1614

EU_OPT R4210 0

1K

C1612 330pF

EU_OPT C1609

1000pF 50V

EU_OPT C1610 1000pF 50V

C1611 330pF 50V

50V

OPT D1618

30V

EU_OPT R1616

75

R1617 10K

R1618 10K

SC1_SOG_IN

SC1_CVBS_IN

SC1/COMP1_DET

ISA1530AC1

EU_OPT R1628 75

EU_OPT R1627

22

EU_OPT R1623 15K

COMPONENT2

6A

5A

4A

7B

5B

7C

5C

5D

4E

5E

6E

PPJ234-01

JK1603

REAR_COMP2

EU_OPT

E

Q1601

B

C

EU_OPT

R4211 390

EU_OPT

R1635 390

Rf EU_OPT C1620

Gain=1+Rf/Rg

100uF 16V

SC1_FB

EU_OPT R1629

3.9K

R1630 12K

R1631 12K

EU_OPT C1618 4700pF

EU_OPT C1619 4700pF

SC1_ID

SC1/COMP1_L_IN

SC1/COMP1_R_IN

[GN]E-LUG

[GN]O-SPRING

[GN]CONTACT

[BL]E-LUG-S

[BL]O-SPRING

[RD]E-LUG-S

[RD]O-SPRING_1

[WH]O-SPRING

[RD]CONTACT

[RD]O-SPRING_2

[RD]E-LUG

EU_OPT

R1640

470

EU_OPT Q1602

2SC3052

C

B

E

EU_OPT

Rg

R1639 180

DTV/MNT_L_OUT

DTV/MNT_R_OUT

EU_OPT R1641 47K

EU_OPT R1642 15K

D1614 30V

EU_OPT C1621 47uF 16V

+3.3V_Normal

OPT

D1612 30V

D1615

30V

IN CASE OF SMALL= 15V

EU_OPT L1606

EU_OPT

C1623

0.1uF 50V

R1612

10K

D1616

5.6V

D1617

5.6V

D1613

5.6V

+12V/+15V

EU_OPT C1625

0.1uF 50V

DTV/MNT_VOUT

R1625 470K

R1626

470K

R1615 1K

R1619 75

R16 20 75

R16 21 75

[SCART AUDIO MUTE]

DTV/MNT_L_OUT

DTV/MNT_R_OUT

EU_OPT Q1607 2SC3052

EU_OPT Q1608 2SC3052

C1616 1000pF 50V

C1617 1000pF 50V

EU_OPT R1648 2K

EU_OPT R1650 2K

R1633 10K

R1632 10K

COMP2_DET

COMP2_Y+

COMP2_Pb+

COMP2_Pr+

R1636

12K

OPT

R1634

12K

OPT

EU_OPT RT1P141C-T112 Q1610

3

2

COMP2_L_IN

COMP2_R_IN

IC1601-*1

SN324

OUT1

1

EU_OPT_AUK

INV_IN1

2

NON_INV_IN1

NON_INV_IN2

EU_OPT

EU_OPT C1644 10uF

16V

C1645 10uF 16V

EU_OPT R1656

2.2K

OPT R1662 470K

EU_OPT R1655

2.2K

EU_OPT R1657

5.6K

EU_OPT R1658

5.6K

OPT R1661 470K

EU_OPT

R1664 33K

EU_OPT C1654 33pF

EU_OPT R1665 33K

C1655

33pF

EU_OPT

EU_OPT R1667 10K

R1668 10K

OUT1

IN1-

IN1+

IN2+

IN2-

OUT2

20110324

CLOSE TO MSTAR

DTV/MNT_L_OUT

C1664

+12V/+15V

SCART1_Lout

C1642

0.1uF 50V

SCART1_Rout

EU_OPT

+3.5V_ST

EU_OPT R1652

10K

1

EU_OPT C1636

0.1uF

R4219 0

R4216 0

SCART1_MUTE

330pF

C1665

330pF

R4218 220K

R4217 220K

DTV/MNT_R_OUT

GP3_S7LR

REAR_JACK

INV_IN2

OUT2

AS324MTR-E1

1

2

3

VCC

4

5

6

7

17

VCC

EU_OPT_BCD

IC1601

3

4

5

6

7

OUT4

14

INV_IN4

13

NON_INV_IN4

12

GND

11

NON_INV_IN3

10

INV_IN3

9

OUT3

8

OUT4

14

IN4-

13

IN4+

12

GND

11

IN3+

10

IN3-

9

OUT3

8

PPJ235-01

LGE Internal Use Only

JK9903

SIDE_AV_3HOLE

5A

[YL]E-LUG

4A

[YL]O-SPRING

3A

[YL]CONTACT

4B

[WH]O-SPRING

3C

[RD]CONTACT

4C

[RD]O-SPRING

5C

[RD]E-LUG

SIDE CVBS PHONE JACK

(New Item Development)

JK9901

KJA-PH-1-0177

SIDE_AV_GENDER

5 M5_GND

4 M4

3 M3_DETECT

1 M1

6 M6

SIDE COMPONENT PHONE JACK

(New Item Developmen)

JK9902

KJA-PH-1-0177

5 M5_GND

4 M4

3 M3_DETECT

1 M1

6 M6

SIDE_COMP

SIDE_CVBS

D9901

OPT

D9902

SIDE_CVBS

D9903

5.6V

SIDE_CVBS

D9904

30V

5.6V

SIDE_COMP

ADUC30S03010L_AMODIODE

ADMC5M03200L_AMODIODE

SIDE_CVBS

+3.3V_Normal

D9907

30V

SIDE_COMP

D9905 30V

D9906

30V

R9907

75

SIDE_CVBS

R9905 470K

R9904

10K

SIDE_COMP

D9908

5.6V

SIDE_CVBS

R9906 470K

OPT

SIDE_COMP

BLM18PG121SN1D

+3.3V_Normal

C9901

100pF

SIDE_CVBS L9902

BLM18PG121SN1D

SIDE_CVBS

L9901

BLM18PG121SN1D

R9910 75

R99 09

SIDE_COMP

75 R99 08

SIDE_COMP

SIDE_CVBS

L9903

SIDE_CVBS

10K

R9911

R9912 1K

SIDE_COMP

75

SIDE_CVBS

C9906

100pF

50V

SIDE_CVBS

C9905

100pF

50V

SIDE_CVBS

R9915 1K

SIDE_CVBS

R99 14

10K

SIDE_CVBS

R99 13

10K

C9907

100pF

OPT

SIDE_CVBS R9917 12K

SIDE_CVBS R9916

12K

COMP2_DET

SIDEAV_CVBS_IN

SIDEAV_DET

SIDEAV_L_IN

SIDEAV_R_IN

COMP2_Y+

COMP2_Pb+

COMP2_Pr+

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

SIDE_JACK

20110324

18

CI Region

LGE Internal Use Only

* Option name of this page : CI_SLOT

(because of Hong Kong)

CI SLOT

+3.3V_Normal

C1901

0.1uF

OPT

/CI_CD1

CI_TS_DATA[4] CI_TS_DATA[5] CI_TS_DATA[6] CI_TS_DATA[7]

CI_IORD CI_IOWR

CI_MDI[0]

CI_MDI[1] CI_MDI[2] CI_MDI[3]

CI_MDI[4]

CI_MDI[5] CI_MDI[6]

CI_MDI[7]

PCM_RST

/PCM_WAIT

REG

CI_TS_CLK

CI_TS_VAL

CI_TS_SYNC

CI_TS_DATA[0] CI_TS_DATA[1] CI_TS_DATA[2] CI_TS_DATA[3]

CLOSE TO MSTAR

CI_MISTRT

CI_MIVAL_ERR

CI_MCLKI

L1901

BLM18PG121SN1D

+3.3V_CI

R1901

C1914 12pF 50V

C1902

0.1uF

AR1901

R1902

47

R1925 33 R1926 R1927 33

AR1903

/CI_CD2

+5V_Normal

33

47

33

+5V_Normal

C1906 10uF 10V

R1909 0

GND

R1903

R1904 10K

10K

C1903

0.1uF 16V

GND

R1906

R1905

C1905

R1907

C1904

0.1uF 16V

R1908 100

10K

0.1uF

10K

100

CI DETECT

/CI_CD2

/CI_CD1

CI POWER ENABLE CONTROL

+5V_Normal

C1907

PCM_5V_CTL

+5V_CI_ON

R1910

OPT

0.1uF 16V

CI_DATA[0-7]

EAG41860102

P1901 P1902

10067972-050LF

10067972-000LF

CI_SLOT_JACK

35

35 36

36 37

37 38

38 39

39 40

40 41

41 42

42 43

43 44

44 45

45 46

46 47

47 48

48 49

49 50

50 51

51

0

52

OPT

53

53 54

54 55

55 56

56 57

57 58

58 59

59

65

65 66

66 67

67 68

68

2

GND

CI_SLOT_OR_GATE_NXP

IC1901

74LVC1G32GW

1B 5 VCC

3GND2A4 Y

R1912

10K

OPT

R1913 10K

1 2 3

3 4

4 5

5 6

6 7

7 8

8 9

9

10

10 11

11 12

12 13

13 14

14 15

15 16

16 17

17

R1916

18

18 19

19 20

20 21

21 22

22 23

23 24

24 25

25 2660

2660 2761

2761 2862

2862 2963

2963 3064

3064 31

31 32

32 33

33 34

34

G1G2

1

69

+3.3V_CI

16V

0.1 uF

C19 08

OPT

GND

R1915

47

R1914 22K

R1922

2.2K

C

Q1901

B

2SC3052

R1924

E

10K

0

OPT

GND

+3.3V_CI

Q1902

RSR025P03

S

C1911

4.7uF 16V

R1919

10K

R1917

R1918

D

G

R1920

0.1uF

47

C1909

CI_DATA[3] CI_DATA[4] CI_DATA[5] CI_DATA[6] CI_DATA[7]

47

100

GND

L1902

BLM18PG121SN1D

C1910

0.1uF

16V

CI_DATA[0] CI_DATA[1] CI_DATA[2]

CI_DET

/PCM_CD

CI_DATA[0-7]

+5V_CI_ON

R1923 10K

OPT

R1921

10K

CI_ADDR[10]

CI_ADDR[11]

CI_ADDR[9]

CI_ADDR[8] CI_ADDR[13] CI_ADDR[14]

CI_ADDR[12]

CI_ADDR[7]

CI_ADDR[6]

CI_ADDR[5]

CI_ADDR[4]

CI_ADDR[3]

CI_ADDR[2]

CI_ADDR[1]

CI_ADDR[0]

C1912

0.1uF 16V

OPT

/PCM_CE

CI_OE

CI_WE

CI_ADDR[0-14]

/PCM_IRQA

CI HOST I/F

CI_DET

PCM_A[0]

CI_ADDR[7]

PCM_A[1]

CI_ADDR[6]

PCM_A[2]

CI_ADDR[5]

PCM_A[3]

CI_ADDR[4]

CI TS INPUT

CI_MIVAL_ERR

CI_DATA[0-7]

CI_MDI[7] CI_MDI[6] CI_MDI[5]

CI_MDI[4]

CI_MDI[3] CI_MDI[2] CI_MDI[1] CI_MDI[0]

CI_MISTRT

CI_MCLKI

CI_DATA[0-7]

CI_ADDR[8]

CI_ADDR[9] CI_ADDR[10] CI_ADDR[11]

CI_ADDR[12] CI_ADDR[13] CI_ADDR[14]

CI_OE

CI_WE CI_IORD CI_IOWR

CI_DATA[0] CI_DATA[1] CI_DATA[2] CI_DATA[3]

CI_DATA[4]

CI_DATA[6] CI_DATA[7]

REG

AR1905

33

AR1906

33

AR1904

33

IC1902

1OE

1

TOSHIBA

1A1

2

0ITO742440D

2Y4

3

1A2

4

2Y3

5

1A3

6

2Y2

1A4

2Y1

GND

TC74LCX244FT

7

8

9

10

AR1907

33

AR1908

33

AR1912

33

AR1913

33

AR1909

33

FE_TS_DATA[7] FE_TS_DATA[6] FE_TS_DATA[5] FE_TS_DATA[4]

FE_TS_DATA[3] FE_TS_DATA[2] FE_TS_DATA[1] FE_TS_DATA[0]

FE_TS_SYNC

FE_TS_VAL_ERR

FE_TS_CLK

+3.3V_CI

VCC

20

2OE

19

1Y1

18

2A4

17

1Y2

16

2A3

15

1Y3

14

2A2

13

1Y4

12

2A1

11

C1913

0.1uF 16V

PCM_D[0] PCM_D[1] PCM_D[2] PCM_D[3]

PCM_D[4] PCM_D[5]CI_DATA[5] PCM_D[6] PCM_D[7]

PCM_A[8] PCM_A[9]

PCM_A[10] PCM_A[11]

PCM_A[12] PCM_A[13] PCM_A[14] /PCM_REG

/PCM_OE

/PCM_WE

/PCM_IORD

/PCM_IOWR

@netLa

FE_TS_DATA[0-7]

CI_ADDR[0]

PCM_A[7]

CI_ADDR[1]

PCM_A[6]

CI_ADDR[2]

PCM_A[5]

CI_ADDR[3]

PCM_A[4]

PCM_D[0-7]

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

GP3_S7LR

PCMCI

20110324

20

SMD GASKET

LGE Internal Use Only

GAS 1

MDL 61930 001

DO_NOT_APPLY

GAS1-*1

5.5T_GAS MDS62110204

GAS1-*2

7.5T_GAS MDS62110205

GAS1-*3

9.5T_GAS MDS62110214

GAS1-*4

12.5T_GAS

MDS61887708

GAS 2

MDL 61930 001

DO_NOT_APPLY

GAS2-*1

5.5T_GAS MDS62110204

GAS2-*2

7.5T_GAS MDS62110205

GAS2-*3

9.5T_GAS

MDS62110214

GAS2-*4

12.5T_GAS

MDS61887708

GAS 3

MDL 61930 001

DO_NOT_APPLY

GAS3-*1

5.5T_GAS MDS62110204

GAS3-*2

7.5T_GAS MDS62110205

GAS3-*3

9.5T_GAS MDS62110214

GAS3-*4

12.5T_GAS MDS61887708

GAS 4

MDL 61930 001

DO_NOT_APPLY

GAS4-*1

5.5T_GAS MDS62110204

GAS4-*2

7.5T_GAS MDS62110205

GAS4-*3

9.5T_GAS MDS62110214

GAS4-*4

12.5T_GAS MDS61887708

GAS 5

MDL 61930 001

DO_NOT_APPLY

GAS5-*1

5.5T_GAS MDS62110204

GAS5-*2

7.5T_GAS MDS62110205

GAS5-*3

9.5T_GAS MDS62110214

GAS5-*4

12.5T_GAS MDS61887708

GAS 6

MDL 61930 001

DO_NOT_APPLY

GAS6-*1

5.5T_GAS MDS62110204

GAS6-*2

7.5T_GAS MDS62110205

GAS6-*3

9.5T_GAS MDS62110214

GAS6-*4

12.5T_GAS MDS61887708

GAS 7

MDL 61930 001

DO_NOT_APPLY

GAS7-*1

5.5T_GAS MDS62110204

GAS7-*2

7.5T_GAS MDS62110205

GAS7-*3

9.5T_GAS MDS62110214

GAS7-*4

12.5T_GAS MDS61887708

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

8.5T_GAS MDS62110209

6.5T_GAS MDS62110206

GAS1-*5

GAS1-*6

8.5T_GAS MDS62110209

6.5T_GAS MDS62110206

GAS2-*5

GAS2-*6

8.5T_GAS MDS62110209

6.5T_GAS MDS62110206

GAS3-*5

GAS3-*6

GAS4-*5

8.5T_GAS MDS62110209

GAS4-*6

6.5T_GAS MDS62110206

GAS5-*5

8.5T_GAS MDS62110209

GAS5-*6

6.5T_GAS MDS62110206

GAS6-*5

8.5T_GAS MDS62110209

GAS6-*6

6.5T_GAS MDS62110206

8.5T_GAS MDS62110209

6.5T_GAS MDS62110206

GAS7-*5

GAS7-*6

GP3_S7LR

SMD_GAS

20110324

20