LG 37LG700H User Manual

Please read this manual carefully before operating
your set.

Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.

LCD TV
OWNER’S MANUAL

32LG700H
37LG700H
42LG700H

Inst

aller Reference for Commercial Mode
MPI/PPV Card Setup see page 19
Commercial Mode Setup see pages 85-107

P/NO : SAC30708043 (0910-REV05)

www.lgcommercial.com

This product qualifies for ENERGY STAR in the “factory
default” setting and this is the setting in which power savings
will be achieved.

Changing the factory default picture setting or enabling other
features will increase power consumption that could exceed
the limits necessary to quality for Energy Star rating.

1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User
1-888-542-2623 CANADA

LG Customer Information Center

Model:

Serial:

1

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi­tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation (of the device).

Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating
and maintenance (servicing) instructions in the
literature accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.

Unplug this apparatus during lighting storms or
when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

2

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

1

2

3

4

5

7

8

6

9

10

3

Never touch this apparatus or antenna during a
thunder or lighting storm.

When mounting a TV on the wall, make sure not to
install the TV by the hanging power and signal
cables on the back of the TV.

Do not allow an impact shock or any objects to fall
into the product, and do not drop onto the screen
with something.

CAUTION concerning the Power Cord :
It is recommend that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet as this could result in fire or elec­tric shock.
Do not overload wall outlets. Overloaded wall out­lets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the
TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.

Do not expose to dripping or splashing and do not
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).

GGRROOUUNNDDIINNGG
Ensure that you connect the earth ground wire to

prevent possible electric shock. (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding
methods are not possible, have a qualified electri­cian install a separate circuit breaker.

Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The plug

must remain readily operable.

12

11

14

13

16

17

18

Powe r
Supply

Short-circuit

Breaker

15

4

AANNTTEENNNNAASS
OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg

If an outdoor antenna is installed, follow the precau­tions below. An outdoor antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
come in contact with such power lines or circuits as
death or serious injury can occur.

Be sure the antenna system is grounded so as to pro­vide some protection against voltage surges and
built-up static charges.

Section 810 of the National Electrical Code (NEC) in
the U.S.A. provides information with respect to prop­er grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes and requirements for the grounding elec­trode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700

Cleaning
When cleaning, unplug the power cord and scrub

gently with a soft cloth to prevent scratching. Do not
spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemi­cals such as alcohol, thinners or benzene.

Moving
Make sure the product is turned off, unplugged

and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.

Ventilation
Install your TV where there is proper ventilation. Do

not install in a confined space such as a bookcase.
Do not cover the product with cloth or other mate­rials (e.g.) plastic while plugged in. Do not install in
excessively dusty places.

Take care not to touch the ventilation openings.
When watching the TV for a long period, the venti­lation openings may become hot.

If you smell smoke or other odors coming from the
TV or hear strange sounds, unplug the power cord
contact an authorized service center.

Do not press strongly upon the panel with a hand or
sharp object such as nail, pencil or pen, or make a
scratch on it.

Keep the product away from direct sunlight.

FF oorr LLCC DD TTVV

If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.

Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary dis­tortion effects on the screen.

21

19

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

22

23

24

25

20

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.

26

27

5

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . .

2

FEATURES OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Stand Instruction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cable Management

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Attaching the TV to a desk

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Securing the TV to the wall to prevent falling
When the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . 17

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 18

MPI Card Slot / PPV Card Installation

. . . . . . . . . . . . . . . 19

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

- Component Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . .20

- HDMI Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

- DVI to HDMI Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 22

DVD Setup

- Component Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

- HDMI Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

VCR Setup

- Antenna Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

- Composite (RCA) Connection

. . . . . . . . . . . . . . . . . . . 25

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

PC Setup

- VGA (D-Sub 15 pin) Connection

. . . . . . . . . . . . . . . 27

- DVI to HDMI Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 28

- Screen Setup for PC mode

. . . . . . . . . . . . . . . . . . . . . . . . 29

Audio Out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . .38

- Add / Delete Channel (Manual Tuning)

. . . . . . 39

- Channel Editing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Channel Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Example Electronic Program Guide

. . . . . . . . . . . . . . . . . . . 43

PICTURE CONTROL

PIP (Picture-In-Picture)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Picture Size (Aspect Ratio) Control

. . . . . . . . . . . . . . . . . . 46

Preset Picture Settings

- Picture Mode - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

- Color Tone - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Manual Picture Adjustment

- Picture Mode - User Mode

. . . . . . . . . . . . . . . . . . . . . . . . 51

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 52

Advanced Control - Black (Darkness) Level

. . . . . . . 53

Advanced Control - Eye Care

. . . . . . . . . . . . . . . . . . . . . . . . . . .54

Advanced Control -

Film Mode . . . . . . . . . . . . . . . . . . . . . . . . .55

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume)

. . . . . . . . . . . . . . . . . 57

Preset Sound Settings (Sound Mode)

. . . . . . . . . . . . . . 58

Sound Setting Adjustment - User Mode

. . . . . . . . . . . 59

- SRS TruSurround XT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Clear Voice

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Stereo/SAP Broadcast Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . .65

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

On-Screen Menus Language Selection

. . . . . . . . . . . . . . 67

Caption Mode

- Analog Broadcasting System Captions

. . . . . . . 68

- Digital Broadcasting System Captions

. . . . . . . . 69

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Auto Shut-off Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

6

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Downloadable Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

COMMERCIAL MODE SETUP

Interactive TV Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Installer Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Interactive TV Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Commercial Mode Setup for Master TV

. . . . . . . . . . . . 88

Master TV Profile Setup Learning/Teaching with
USB Memory Card

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

TLL-1100A Cloning Connections/Learning Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

91

LT2002 Cloning Connections/Learning Setup

. . 92

LT2002 Cloning Learning Setup

. . . . . . . . . . . . . . . . . . . . . . 93

Cloning Connections/Teaching Setup

. . . . . . . . . . . . . . 94

Installer Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

95

Reference: Detailed Instructions For Making A
Master TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101

Reference: Procedures for adding Channel Label
Icons/Custom Channel Labels (2-5-4 + MENU
Mode)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2

Reference: Clonable Menu Features

. . . . . . . . . . . . . . . . 10 3

Reference: Power Saving Setup

. . . . . . . . . . . . . . . . . . . . . . . 10 4

TV Aux Input Configuration

. . . . . . . . . . . . . . . . . . . . . . . . . . .10 6

TV Camport Auto Sense Operation

. . . . . . . . . . . . . . . . 107

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

Reference: LT2002 Cloning Procedure
Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Troubleshooting Flow Chart

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Commercial Mode Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Reference: RJP model list and input hierarchy

. . . 112

Glossary of Terms

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Programming the Remote Control

. . . . . . . . . . . . . . . . . . . 115

IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Open Source License

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 0

7

FEATURES OF THIS TV

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

USB IN

SERVUCE ONLYSERVUCE ONLY

USB port shall be used for software update by service
personnel only.

HDMI

TM

, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing."

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN

8

PREPERATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner’s Manual

Power Cord

CD Manual

Protective Bracket and

Bolt for Power Cord

(Refer to P.13)

Cable Holder

(Refer to P.13)

* Wipe spots on the exterior only with the pol-

ishing cloth.

* Do not wipe roughly when removing stains.

Excessive pressure may cause scratches or
discoloration.

Polishing Cloth

(Not included with all

models.)

FFoorr 3322LLGG770000HH

OOppttiioonn EExxttrraass

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.

x 2

Torx plus

Star head screw

(Refer to P.12)

Screw for stand fixing

(Refer to P.15)

Bolts for stand assembly

(Refer to P.12)

x 4 x 4

1.5V 1.5V

Remote Control,

Batteries

M
U

TE

RETURN

C

C

TV

P

O

W

ER

GUIDE

PORTAL

ENT

E

R

VOL

CH

123

456

78

0

9

FLASHB

K

VCR

DVD

INPU

T

M

E
NU

INFO

i

STB

P

A

G

E

PIP

SAP

PIP CH-

PIP CH+

PIP SWAP

PIP INPU

T

ALPHA/NU

M

RE

M
OVE

RATIO

TIM

E
R

ABC

DEF

GHI

WX

Y
Z

T
U

V

PQRS

MNO

JKL

&
@

.:/,

Protection Cover

(Refer to P.12)

Plug in type Holder

(Refer to P.13)

PREPARATION

9

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

POWER Button

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is switched on.

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

Remote Control Sensor

CHANNEL( , )
Buttons

Stand

Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

CH

VOL

ENTER

MENU

INPUT

PREPARATION

10

PREPARATION

■

Image shown may differ from your TV.

BACK PANEL INFORMATION

R

/

8

2

4

R

ANTENNA IN

M.P.I.

7

1

3

5

6

9

10

11

12

13

15

14

11

USB

SERVICE ONLY

R

AUDIO

L/MONO

VIDEO

ANTENNA IN

M.P.I.

AV IN 2

HDMI/DVI IN

2

1(DVI)

INTERFACE

RJP

(SERVICE ONLY)

(PC)

RGB

LAN

RESET

RGB IN

AUDIO

(RGB/DVI)

UPDATE

RS-232C IN

(SERVICE ONLY)

OPTICAL

DIGITAL

AUDIO OUT

SPEAKER

OUT

8

REMOTE
CONTROL

OUT

VIDEO

COMPONENT IN

AUDIO

AV IN 1

AUDIO

/

MONO

VIDEO

PREPARATION

11

REMOTE CONTROL OUT

IR output for controlling an auxiliary device.

RJP INTERFACE (REMOTE JACK PACK PORT)

Connect to remote jack pack control output port.

COMPONENT IN

Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & a red

and white cable for audio.

AV (Audio/Video) IN 1

Analog composite connection. Supports standard
definition video only (480i).

Used for PC/DTV audio input jack.

USB SERVICE ONLY

Used for software updates.

ANTENNA IN

Connect over-the air signals to this jack.

M.P. I.

Control port.

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

HDMI/DVI IN

Digital Connection. Supports HD video and Digital
audio.

Accepts DVI video using an adapter or HDMI to
DVI cable (not included)

LAN (SERVICE ONLY)
For connecting to a control network.

RESET

Performs a hardware reset.

UPDATE

Enables/disables software downloads and debug
mode.

OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and
home theater systems.

Note: In standby mode, this port doesn’t work.

SPEAKER OUT 8

Ω

Connect to external speaker input.

RGB (PC)

Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable).

AUDIO (RGB/DVI)

1/8” headphone jack for analog PC audio input.

RS-232C IN (SERVICE ONLY)

Used for software updates.

1

2

3

4

5

9

8

6

7

10

11

12

13

14

15

PREPARATION

12

STAND INSTRUCTION

PREPARATION

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the

SSTTAANNDD BBOODDYY

to the

CC OOVVEERR

BBAA SS EE

with the included screws.

1

2

Insert the stand as shown.

3

SSTTAANNDD BBOODD YY

CCOOVVEERR BBAASSEE

■

Image shown may differ from your TV.

GG

Make sure the screws in the stand are fully
tightened. (If not tightened fully, the product
could tilt forward and fall). But do not over
tighten, over-tightening can damage the threads
on the screws.

NOTE

!

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Remove the four screws that hold the base on.

2

Detach the stand from TV.

3

INSTALLATION

4

or

x 4

Tighten the stand with the
four screws (provided as parts
of the TV).

Tighten the two of these four screws
and the two Torx plus star head screws

(provided as parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a star head dri­ver bit (not provided as parts of the TV).

x 2

x 2

After removing the stand, install the included
pp rr oott eeccttiioonn cc oovveerr

over the hole for the stand.

Press the

PPRROOTTEECC TT IIOONN CCOOVVEERR

into the TV

until you hear it click.

PROTECTION COVER

PREPARATION

13

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PPROTECTIVE

BRACKET/Screw or the Plug in type
Holder(For 32LG700H model). It will help

prevent the power cable from being removed
by accident.

Install the CABLE MANAGEMENT CLIP as
shown.

If your TV has the CABLE HOLDER, install it
as shown and bundle the cables.

1

2

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

GG

Do not hold the CABLE MANAGEMENT CLIP
when moving the TV.

- If the TV is dropped, you may be injured or the
product may be broken.

GG

With some TVs, the PLUG IN TYPE HOLDER
and the CABLE HOLDER are included. If these
holders are inserted into the hole provided on
back of the TV, they cannot be removed.

NOTE

!

CABLE MANAGEMENT CLIP

CABLE HOLDER

PROTECTIVE BRACKET/Screw

(This feature is not available for

all models.)

PLUG IN TYPE HOLDER
(For 32LG700H model)

Or

PREPARATION

14

PREPARATION

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on all four sides.

■

Image shown may differ from your TV.

4 inches

4 inches

4 inches

4 inches

SWIVEL STAND

The TV can be conveniently swivelled on its stand 90° to the left or right to provide the optimum viewing angle.

GG

Ensure adequate ventilation by following the clearance recommendations.

GG

Do not mount near or above any type of heat source.

CAUTION

PREPARATION

15

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.

GG

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

4-Screws

(not provided as parts of the product)

GG

Screw: M5 x L (

*L: Table depth + 8

~10 mm)

ex) Table depth: 15mm, Screw: M5 x 25

Desk

Stand

PREPARATION

16

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materi­als, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.

GG

Do not install your wall mount kit while the TV is plugged in. It may result in personal injury due to electric
shock.

CAUTION

GG

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

GG

Standard dimensions for wall mount kits are shown
in the table.

GG

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

GG

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to
the TV.

GG

For wall mounts that do not comply with the VESA

standard screw specifications, the length of the
screws may differ depending on their specifica­tions.

GG

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not tighten the screws too much. It may dam­age the TV or allow the TV to a fall and cause per­sonal injury. LG is not liable for these kinds of acci­dents.

GG

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

AA

BB

GG

To prevent injury, this apparatus must be securely attached to the wall in accordance with the installa­tion instructions.

WARNING

Product Model

VESA

(A *B)

Standard Screw Quantity

32LG700H

37LG700H

42LG700H

200 * 100

M4

4

LCD TV

200 * 200

200 * 200

M6

M6

4

4

PREPARATION

17

SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND

We recommend that you set the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert eye-bolts (or TV brackets and bolts) to attach the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with screws (sold separately) to the wall. Match the height of the bracket that
is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope or cord (sold separately) to tie the product. It is
safer to tie the rope so it becomes horizontal between the wall and
the product (the less slack in the rope, the better).

■

You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

■

Image shown may differ from your TV.

* This feature is not available for all models.

GG

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.

GG

To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are
the same.

NOTE

!

R

ANTENNA INANTENNA IN

M.P.I.

PREPARATION

18

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.

For optimum picture quality, adjust the direction if needed.

2. Cable

Wall
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire
when connecting the antenna.

Copper Wire

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

R

/

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

R

ANTENNA INANTENNA IN

M.P.I.

PREPARATION

19

MPI CARD SLOT / PPV CARD INSTALLATION

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

3. Detach RF cable.

4. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

5. Insert card all the way into the slot making sure it is fully seated into back plane connector.

6. Replace the two card retainer screws.

The MPI card is equipped with an RF jack for antenna/cable signal source connection.
The MPI card slot is also available for installing a PPV (Pay-Per-View) card.

MPI Card Removal / PPV Card Installation

RF CABLE

RF cable needs to be
disconnected to remove
the current card.

ANTENNA IN

M.PM.P.I.

M.P. I.

Card Slot

PREPARATION

20

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP

This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,
if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as
shown below.

Component Connection

1. How to connect

Connect the video outputs (Y, P B, PR

)

of the digital set-

top box to the

CC OOMM PP OONNEE NNTT IINN VVIIDDEEOO

jacks on

the TV. Match the jack colors (Y = green, P

B = blue, and

P

R = red).

Connect the audio output of the digital set-top box to
the

CC OOMM PP OONNEE NNTT II NN AAUUDDIIOO

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

CC oommpp oonnee nn tt

input source using the

IINNPPUUTT

button

on the remote control.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

UPDA

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

RGB

(PC)

AUDIO

(RGB/DVI)

RGB IN

RS

(SER

/

VIDEO

AUDIO

COMPONENT IN

Y L RP

B

P

R

1

2

Y, CB/PB, CR/PR

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

Signal

480i

480p

720p

10 8 0 i

10 8 0 p

Component

Yes

Yes

Yes

Yes

No

HDMI

No

Yes

Yes

Yes

No

EXTERNAL EQUIPMENT SETUP

21

HDMI Connection

Connect the digital set-top box to

HHDDMMII //DDVVII II NN 11

((DDVV II )) or22

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDDMMII11

or

HHDDMMII22

input source with using the

IINNPPUUTT

button on the remote control.

2

1

HDMI-DTV

HDMI/DVI IN

2

1(DVI)

RJP

INTERFACE

VID

RGB

/

HDMI/DVI IN

2

1(DVI)

HDMI-DTV OUTPUT

1

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480p

1280x720p

1920x1080i

EXTERNAL EQUIPMENT SETUP

22

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

UP

RESET

LAN

(SERVICE ONLY)

RJP

INTERFACE

COMPONENT IN

VIDEO

AUDIO

RGB IN

(S

HDMI/DVI IN

2

1(DVI)

AUDIO

(RGB/DVI)

LR

DVI-DTV OUTPUT

L

R

RGB

(PC)

1

2

GG

A DVI to HDMI cable or adapter is required for this
connection. DVI doesn't support audio, so a separate
audio connection is necessary.

NOTE

!

Connect the DVI output of the digital set-top box to
the

HHDDMMII //DDVVII IINN 11 (( DD VVII ))

jack on the TV.

Connect the audio output of the digital set-top box to
the

AAUUDDIIOO ((RRGGBB //DDVVII))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s man­ual for the digital set-top box.

)

■

Select the

HHDDMMII 11

input source on the TV using the

IINNPP UUTT

button on the remote control.

2

1

EXTERNAL EQUIPMENT SETUP

23

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPB PR

Video output ports

on DVD player

Y

Y

Y

Y

PB

B-Y

Cb

Pb

PR

R-Y

Cr

Pr

Connect the video outputs (Y, PB

, PR

)

of the DVD to the

CC OOMM PP OONNEE NNTT II NN VVIIDDEEOO

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and PR = red

)

.

Connect the audio outputs of the DVD to the

CC OOMM PP OONNEE NNTT II NN AAUUDDIIOO

jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

CC oommpp oonnee nn tt

input source on the TV using the

IINNPPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

UPDAT

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

RGB

(PC)

AUDIO

(RGB/DVI)

RGB IN

RS

(SER

/

VIDEO

AUDIO

COMPONENT IN

Y L RP

B

P

R

1 2

EXTERNAL EQUIPMENT SETUP

24

EXTERNAL EQUIPMENT SETUP

HDMI Connection

Connect the HDMI output of the DVD to the

HHDDMMII //DDVVII IINN 11 (( DD VVII )) or22

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HHDDMMII11 orHHDDMMII22

input source on the TV

using the

IINNPPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

HDMI/DVI IN

2

1(DVI)

RJP

INTERFACE

CO

VIDEO

RGB

(PC)

/

HDMI/DVI IN

2

1(DVI)

HDMI OUTPUT

1

EXTERNAL EQUIPMENT SETUP

25

VCR SETUP

Antenna Connection

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

ANTENNA IN

M.P.I.

Wall Jack

Antenna

1

2

Connect the RF antenna out socket of the
VCR to the

AANNTTEENNNNAA IINN

socket on the

TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

Composite (RCA) Connection

Connect the

AAUUDD II OO/VVII DD EEOO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

)

■

Select the

AAVV 11

input source on the TV using the

IINNPPUUTT

button on the remote control.

■

If connected to

AAVV II NN 22

, select

AAVV22

input source on the TV.

1

GG

If you have a mono VCR, connect the audio cable
from the VCR to the

AAUUDDIIOO LL //MMOONNOO

jack of the

TV.

NOTE

!

L

R

S-VIDEO

VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

OPTICAL

DIGITAL

AUDIO OUT

UPDATE

AV IN 1

AUDIO

VIDEO

/

REMOTE

CONTROL

OUT

SPEAKER

OUT

8

RS-232C IN

(SERVICE ONLY)

MONO

/

AV IN 1

AUDIO

VIDEO

MONO

/

1

EXTERNAL EQUIPMENT SETUP

26

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

Camcorder

Video Game Set

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks
between TV and external equipment.
Match the jack colors

.

(

Video = yellow, Audio Left = white, and

Audio Right = red

)

1. How to connect

2. How to use

■

Select the

AAVV 22

input source on the TV using the

IINNPP UUTT

button on the remote control.

■

If connected to

AAVV II NN 11

input, select the

AAVV 11

input source on the TV.

■

Operate the corresponding external equipment.

1

1

USB IN

R

AUDIO

L/ MONO

VIDEO

AV IN 2

VIDEO

L R

EXTERNAL EQUIPMENT SETUP

27

PC SETUP

GG

To get the best picture quality, adjust the PC graph­ics card to 1360x768, 60Hz.

GG

Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.

GG

In PC mode, there may be noise associated with the
resolution, vertical pattern, contrast or brightness.
If noise is present, change the PC output to anoth­er resolution, change the refresh rate to another
rate or adjust the brightness and contrast on the
PICTURE menu until the picture is clear.

NOTES

!

Supported Display Specifications
(RGB-PC, HDMI-PC)

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

COMPONENT IN

VIDEO

AUDIO

AV IN 1

RS-232C

(SERVICE O

AUDIO

(RGB/DVI)

RGB IN

RGB OUTPUT

AUDIO

RGB

(PC)

1

2

2. How to use

■

Turn on the PC and the TV.

■

Select the

RRGG BB--PP CC

input source on the TV using the

IINNPPUUTT

button on the remote control.

Connect the VGA output of the PC to the

RR GG BB ((PP CC

))

jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO ((RRGGBB//DDVVII

))

jack on the TV.

1. How to connect

2

1

Resolution

720x400

1360x768

640x350

640x480

800x600

1024x768

1280x768

1280x1024

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.09

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47. 776 59.870

47.712 60.015

63.981 60.020

When you use too long RGB-PC cable, there might
be a noise on the screen.

GG

Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could become
permanently imprinted on the screen.

GG

The synchronization input form for Horizontal and
Vertical frequencies is separate.

GG

Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.

EXTERNAL EQUIPMENT SETUP

28

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

UP

RESET

LAN

(SERVICE ONLY)

RJP

INTERFACE

COMPONENT IN

VIDEO

AUDIO

R

(S

AUDIO

(RGB/DVI)

RGB IN

HDMI/DVI IN

2

1(DVI)

RGB

(PC)

DVI-PC OUTPUT AUDIO

1

2

2. How to use

■

Turn on the PC and the TV.

■

Select the

HHDDMMII11

input source on the TV using the

IINNPPUUTT

button on the remote control.

Connect the DVI output of the PC to the

HHDDMMII//DDVVII IINN

11 ((DDVVII))

jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO ((RRGGBB//DDVVII))

jack on the TV.

1. How to connect

2

1