LG 47LD555H, 42LD555H, 32LD555H, 32LD665H, 32LD660H User Manual

...

32LD660H 37LD660H 42LD660H 32LD665H 37LD665H 42LD665H

32LV555H 37LV555H

Lodging Guest Interactive Pro:Centric™ TVs

Commercial Mode Setup Guide

Note: Selected features shown in this guide may not be available on all models.

42LV555H 47LV555H 55LV555H

EXPERIENCED INSTALLER

Master TV Setup pages 11 – 14

Cloning Information pages 24 – 32

FTG Mode of Operation pages 33 – 44

P/N: 206-4200 (Rev B)

For Customer Support/Service, please call:

1-888-865-3026

The latest product information and documentation is available online at:

www.LGsolutions.com/products

MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:

Model No._________________ Serial No._______________

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

206-4200

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination in order to avoid injury from tip-over.

PORTABLE CART WARNING

13.

Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Never touch this apparatus or antenna during a thunder or

lighting storm.

15. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.

16. Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.

17. Power Cord Caution: It is recommended that appliances be placed

upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page in the Owner’s Manual to be certain.

Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not use a damaged or loose power cord. Be sure to grasp

the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

18. Overloading Do not connect too many appliances to the same AC power

outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in re or electric shock.

19. Outdoor Use/Wet Location Warning: To reduce the risk of re or electrical shock, do not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this prod-

uct near ammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place

objects lled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).

20. Grounding

Ensure that you connect the earth ground wire to prevent

possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualied electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.

21. Disconnect Device

The mains plug is the disconnecting device. The plug must

remain readily operable.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this unit by SWITCH.

(Continued on next page)

206-4200

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the

product, follow the precautions below.

An outdoor antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide

some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A.

provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

Ground Clamp

Electric Service

Equipment

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

23. Cleaning When cleaning, unplug the power cord and wipe gently with

a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product Make sure the TV is turned Off and unplugged and that all

cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.

25. Ventilation Install the TV where there is proper ventilation. Do not install

in a conned space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.

26. Do not touch the ventilation openings, as they may become

hot while the TV is operating.

27. If you smell smoke or other odors coming from the TV or

hear strange sounds, unplug the power cord, and contact an authorized service center.

28. Do not press against the front panel of the TV with your

hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.

29. Keep the product away from direct sunlight.

30. Dot Defect

The LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see ne dots on the screen while you are viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

31. Generated Sound

“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

32. For LCD TV

If the TV feels cold to the touch, there may be a small “icker” when it is turned On. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your nger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

206-4200

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . 6 – 7

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Management in FTG Mode . . . . . . . . . . . . . . . . . 7

External MPI Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pro:Centric Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 – 9

Pro:Centric TV Interactive Menu Features . . . . . . . . . . . . 8

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pro:Centric Modes of Operation . . . . . . . . . . . . . . . . . . . . 9

Installer Remote Control Typical Key Functions . . . . . . . . 10

Master TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 – 14

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cloning Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Clonable TV Setup Menu Features . . . . . . . . . . . . . . . . .11

Master TV Setup Procedure . . . . . . . . . . . . . . . . . . . . . . 12

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 – 22

Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . . . 15

Using the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . 15

Exiting the Installer Menu and Activating Updates . . . . . 15

Channel Icons / Custom Text Labels

(2-5-4 + MENU Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Cloning Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

USB Cloning Procedures. . . . . . . . . . . . . . . . . . . . . . 25

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tlx File. . . . . . . . . . . . . . . . . . . 25

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tll File . . . . . . . . . . . . . . . . . . . .

Clone Programmer Cloning Procedures . . . . . . . . . 29

Learning / Teaching a Master TV Setup using

a TLL-1100A Clone Programmer . . . . . . . . . . . . . . . . . . 29

Learning / Teaching a Master TV Setup using

an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . . . 31

FTG Mode of Operation Overview . . . . . . . . . . . . . . 33

FTG Mode via CPU or EBL . . . . . . . . . . . . . . . . . . . . . . 33

Determining the TV Operating Mode . . . . . . . . . . . . . . . 34

FTG Mode via CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Creating an FTG Configuration File using the

FTG File Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

–

27 32

Teaching FTG Configuration to a TV . . . . . . . . . . . . . . . 37

Learning an FTG Configuration File from a TV . . . . . . . 38

Optional Manual Configuration / TV Setup . . . . . . . . . . . 39

FTG Mode via EBL (Local Configuration) . . . . . . . . . . . 40

FTG File Manager Utilities Overview . . . . . . . . . . . . . . 41 – 44

FTG File Manager Main Screen . . . . . . . . . . . . . . . . . . . 41

FTG Channel Map Configuration Utility . . . . . . . . . . . . . 42

FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . . . 43

FTG Installer Menu Configuration Utility. . . . . . . . . . . . . 44

IP Environment Setup . . . . . . . . . . . . . . . . . . . . . . . . 45 – 46

Access the IP Environment Menu. . . . . . . . . . . . . . . . . . 45

Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Offset Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Remote Jack Pack / TV Connections & Setup . . . . . . . . . 47

References

Upgrading TV/PTC Software using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Downloading a Splash Screen using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Power Consumption Settings . . . . . . . . . . . . . . . . . . . . 50 – 51

TV Camport Auto Sense Operation . . . . . . . . . . . . . . . . . . 52

TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . 53

b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 54

RJP Model List and Input Auto-sensing Hierarchy. . . . . . . 55

Resetting Factory Defaults on the TV(s) . . . . . . . . . . . . . . 56

TV Zone Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

LD660H/LD665H Rear Jack Panel . . . . . . . . . . . . . . . . . . 58

LV555H Rear Jack Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Side Connections Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

RF Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 62

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . 63

Commercial Mode Check / FTG Operation

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Clone Programmer Troubleshooting. . . . . . . . . . . . . . . . 65

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Document Revision History / Notes . . . . . . . . . . . . . . . . . . 67

Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

– 65

Notes

• Installer Menu content is intended for use primarily by qualied TV electronics technicians.

• Refer to the Owner’s Manual for additional information on TV installation, features, specications, maintenance, and safety instructions.

• Design and specications subject to change without prior notice.

206-4200

Commercial Mode Overview

This document describes how to set up LD660H/LD665H and LV555H Pro:Centric™ TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider).

Each of these TV models has an EBL module that can be configured either for Pass-through Mode (default) or Free-To-Guest (FTG) Mode. In addition, each of these TVs is capable of FTG Mode operation via the TV CPU when the EBL is in Pass-through Mode.

Setup Checklist

Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s

Manual for detailed information on TV installation and hardware and cable connections.

Installation

__ Unpack TV and all accessories. __ Install batteries in the Installer Remote.

Cable Connections

__ Make all rear jack panel and MPI card slot

connections, as appropriate. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable

connections before installing on VESA mount or stand, as appropriate.

Commercial Mode Setup

__ Complete appropriate procedures as described

in this document for Commercial Mode operation.

See “Pass-through Mode” and “FTG Mode”

Hardware Connections

sections below for further information. __ Install any additional hardware as

appropriate to your institution, LAN, etc.

Pass-through Mode

This mode allows you to create a Master TV Setup for cloning purposes for TVs that are to remain in Passthrough Mode. This mode also allows external control via the GAME CONTROL/MPI port on the TV rear jack panel. Use the Installer Remote to congure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). See “Master TV Setup” on pages 11 to 14 for detailed information.

Installer Menu

To set up a Master TV for cloning purposes, you will need to know how to enter the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 15 to 22 for information on accessing the Installer Menu in Passthrough Mode and for detailed descriptions of the Installer Menu items.

xxLD66xH PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 ASIC D279 PTC V1.00.016 CPU V1.21.00

Typical Installer Menu

TV Setup Menus

On-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. Refer to the Owner’s Manual for detailed information on the TV setup menus.

CHANNEL

OPTION

PICTURE

LOCK

TV Setup Menus

AUDIO

INPUT

TIME

USB

206-4200

Commercial Mode Overview (Cont.)

Cloning

Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV (both TVs must be in Pass-through Mode). The Master TV’s clonable setup menu options should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. Pages 24 to 32 provide detailed information on cloning requirements and procedures.

FTG Mode

This mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be used is vital in determining the owner.

As indicated above, FTG mode operation in the LD660H/LD665H and LV555H models can be provided either by the TV CPU or EBL. These are two separate and distinct FTG Modes of operation, each with its own unique advantages and requirements as described later in this document. When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.

Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, conguration can begin. Conguration of either requires a PC application—the LG FTG File Manager for the TV CPU or the LG FTG Device Conguration Application for the EBL. Each application provides utilities that enable you to create/edit an FTG Channel Map and congure Installer Menu settings. See pages 33 to 44 for further information on FTG Mode operation and conguration.

Remote Management in FTG Mode

When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.

When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See Reference section, “b-LAN Setup & Overview,” for further information.

External MPI Control

To control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as Reference section, “b-LAN Setup & Overview,” for further information.

206-4200

Pro:Centric Operation

Pro:Centric TV Interactive Menu Features

The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities. The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities charges are billed at the time of order.

Interactive amenities may include:

• Hotel information, news, and events

• Directory services (tourist attractions, restaurants, etc.)

• Reservation services (business meetings, tness, spa, etc.)

• Weather and trafc information

STB

GUIDE

RETURN

VOL

PQRS

.:/,

GHI

POWER

PORTAL

ENTER

ALPHA/NUM

MUTE

REMOVE

ABC

JKL MNO

TUV

DVD

VCR

INFO

INPUT

FLASHBK

P A G E

DEF

WXYZ

• Shopping services (delivery to guest room)

• Room service (menu ordering, memo service, morning wake up call, laundry, etc.)

• Ticketing and gaming services

• Check-out service (in the guest room)

• E-mail resources/account access

Use the Installer Remote to operate both interactive menus and regular TV features. Press PORTAL on the Installer Remote to access the interactive menus.

Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.

Channel Guide

Shows available TV networks and logical channels. When available, electronic program guide (EPG) data provides additional channel and program information.

Information

Typically displays hotel information, for example, photos of guest rooms, dining rooms, business centers, facilities, etc., as well as information on local weather and attractions. Information may also include resources, such as local school programs, run in cooperation with the hotel.

Help

Provides help for navigating the interactive menus.

PIP CH-

RATIO

PIP

PIP CH+

TIMER

PIP SWAP

SAP

PIP INPUT

Watch TV

Removes the interactive menu from the screen and returns to the previously tuned TV channel.

206-4200

Pro:Centric Operation (Cont.)

Pro:Centric Setup

The Pro:Centric server provides the following functionality:

• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU (see also “Remote Management in FTG Mode” on page 7).

The Data Channel must be set appropriately to enable Pro:Centric remote management/administration facilities. The Data Channel can be set either in the Installer Menu (item 119 DATA CHANNEL) or in the Pro:Centric Menu (see “Pro:Centric Setup” on page 46).

• Pro:Centric application: The application comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric application settings are managed via the Pro:Centric server Admin Client.

In addition to the Data Channel, the Pro:Centric Application Mode must be set appropriately to enable the Pro:Centric application. The Pro:Centric Application Mode can be set either in the Installer Menu (item 098 PRO:CENTRIC) or in the Pro:Centric Menu (see “Pro:Centric Setup” on page 46).

Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric™ Server Admin Client User Guide. This document describes only those settings that must be specied on the TVs.

Pro:Centric Modes of Operation

There are now two modes that enable Pro:Centric operation, as described below.

FTG Mode via CPU

This mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels as described in the introduction to this document. See pages 33 to 44 for further information on FTG Mode operation and conguration.

Application Tuning Mode

If the TV is not in FTG Mode, but both the Data Channel and the Pro:Centric Application Mode have been set in the Installer Menu or the Pro:Centric Menu, the TV enters Application Tuning Mode. In Application Tuning Mode, the logical channel mapping of physical channels is done in the Pro:Centric application.

Also in Application Tuning Mode, only the Function Menu is available to end users instead of the TV setup menus (see sample display of the Function Menu under “Determining the TV Operating Mode” on page

34). Additionally, all Channel Map updates must be administered from the Pro:Centric server Admin Client;

Teach To TV options will not be available from the USB Download Menu.

Note: The Installer Menu remains editable while the TV is in Application Tuning Mode.

206-4200

Installer Remote Control Typical Key Functions

The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV.

GUIDE

Displays and removes the electronic

program guide.

PORTAL

Displays and removes the interactive

menu.

INFO

Displays channel information.

VOLUME UP/DOWN

Increases/decreases sound level.

Press to activate subtitles.

MUTE

Switches sound ON or OFF.

CHANNEL/PAGE UP/DOWN

Changes the channel. Moves from

one full set of screen information to

the next.

DVD/VCR BUTTONS

Control some LG DVD/VCR products.

(RECORD button not functional in DVD

mode.)

Color buttons access special functions

in some menus.

PIP

Toggles through PIP options.

PIP CH +/-

Changes the PIP channel.

PIP SWAP

Exchange the main/sub images.

PIP INPUT

Select the connected input source for the

sub-picture.

STB

GUIDE

RETURN

VOL

.:/,

GHI

PQRS

PIP

PIP CH-

POWER

PORTAL

ENTER

ALPHA/NUM

MUTE

REMOVE

ABC

JKL MNO

TUV

RATIO

TIMER

PIP SWAP

PIP CH+

DVD

VCR

INFO

INPUT

FLASHBK

SAP

PIP INPUT

WXYZ

TV/STB/DVD/VCR Select the remote’s operating mode: TV, STB, DVD, or VCR.

POWER Turns TV or any other programmed equipment ON or OFF, depending on mode.

Arrows (Up/Down/Left/Right) & ENTER Use to navigate on-screen menus and adjust TV settings to your requirements.

RETURN Returns one level to the previous menu/display.

MENU Displays the TV setup menus on the screen.

P A G E

Also exits the on-screen menu system and returns to TV viewing.

INPUT Selects RGB, HDMI/DVI1, HDMI2, Component Input, AV1, and AV2 sources.

DEF

NUMBER Buttons (0 - 9) & DASH Use to enter a program number or channel. Dash is used for sub-channel numbers such as 2-1, 2-2, 9-1, 9-2, 100-3, 100-4, etc.

FLASHBK (FLASHBACK) Returns to the previously tuned channel.

RATIO Adjusts the picture aspect ratio.

TIMER Sets the amount of time before the TV automatically turns itself OFF.

SAP Analog Mode: Selects MTS sound (Mono, Stereo, or SAP). DTV Mode: Changes the audio language, if additional languages are available. *

SAP notes:

• If SAP is selected and no SAP is provided, sound

may not be heard on channel.

• Each analog channel may have its own SAP setting.

• Digital channels will reset to default audio language

with a power off/on.

206-4200

Master TV Setup

This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through Mode.

Note: Refer to FTG Mode information on pages 33 to 44 for details on entering FTG Mode and conguring/editing FTG Channel Map and FTG Installer Menu settings.

Before You Begin

• Disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions, Auto Tuning is disabled if there is an Aux input active.

• Determine which cloning tool—USB memory device or clone programmer—is appropriate for your application; several of the Master TV Setup procedure steps are dependent on the cloning tool to be used. See “Cloning Methods” below for further information.

• If you intend to use a USB memory device, determine the type of le—either the new “.tlx” le format or the legacy “.tll” le format—to use for cloning purposes; several of the Master TV Setup procedure steps are dependent on the desired le type. See “Cloning Methods” below for further information.

Cloning Methods

Using a USB Memory Device / .tlx File

• The .tlx le format clones the following menu settings: Installer Menu settings, IP Environment Offset Setup and Pro:Centric Setup settings (see pages 45 and 46), and all TV sources’ (analog, digital, AV1, HDMI, etc.) clonable setup menu settings. See “Clonable TV Setup Menu Features” list below.

• Not intended for cloning an auto-tuned/edited Channel Map, as the channel lineup is converted to a logical FTG Channel Map when saved (Learned) from a TV to a .tlx le. If the .tlx le with the FTG Channel Map is then used for Teaching purposes, all Target TVs will be congured for FTG Mode via CPU.

Using a USB Memory Device / .tll File

The .tll le format clones the contents of the commercial controller (PTC) memory, including an auto-tuned/ edited Channel Map, Installer Menu settings, and one TV source’s (analog, digital, or Aux) clonable setup menu settings. See “Clonable TV Setup Menu Features” list below.

Using a Clone Programmer (TLL-1100A or LT2002)

Both the TLL-1100A and LT2002 clone the contents of the commercial controller (PTC) memory, including an auto-tuned/edited Channel Map, Installer Menu settings, and one TV source’s (analog or Aux) clonable setup menu settings. See “Clonable TV Setup Menu Features” list below.

Clonable TV Setup Menu Features

Channel

Auto Tuning (Channel Lineup) Manual Tuning Channel Edit Channel Label

Picture Aspect Ratio Picture Mode

Note: Some menu options vary between analog and digital channels and Aux inputs.

Audio

Auto Volume Clear Voice Sound Mode Balance TV Speaker

Time Auto Clock Auto Off (Sleep Timer)

Option

Menu Language

Audio Language

Caption

Lock Movie Rating TV Rating – Children TV Rating – General

206-4200

Master TV Setup (Cont.)

Master TV Setup Procedure

1. Set Installer Menu items.

This step provides specic instruction only on the Installer Menu items that should be set on a Master TV. Refer to pages 15 to 22 for detailed information on all Installer Menu items.

a) Make sure the TV is ON. Then, use the Installer Remote to

enter the PTC Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.

b) Set Installer Menu item 117 FACT DEFAULT to 001 and press

ENTER on the Installer Remote.

This clears all Installer Menu custom settings, channel lineup, etc. and reloads the factory default settings. The value will change back to 0 after the PTC has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup.

c) Set Installer Menu item 003 BAND/AFC, as appropriate.

• Broadcast: Set to 000. • HRC: Set to 002.

• CATV: Set to 001 (default). • IRC: Set to 003.

d) Set any other Installer Menu items that affect your TV pro-

gramming network to the required conguration. For example, enable/disable Aux inputs, set a Start Channel, etc.

e) After you have adjusted all required Installer Menu item

settings, press ENTER once on the Installer Remote to save your changes; then, press ENTER again to exit the menu.

2. Set up TV features.

On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Lock, Time, etc. options to the desired configurations. See also the Clonable TV Setup Menu Features list on page 11.

Note: If you intend to clone the PTC, remember that only one TV source’s clonable setup menu settings will be cloned. Thus, for a clone programmer, the TV setup menu settings should be applicable to either an analog channel or Aux input, while for a USB device / .tll file, the TV setup menu settings should be applicable to the analog or digital channel or Aux input to which the Target TV will be set during the Teaching process.

Note: If desired and if appropriate depending on the cloning method you intend to use (see “Cloning Methods” on previous page), you can run Auto Tuning (see step 3) prior to completing this step.

xxLD66xH PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 ASIC D279 PTC V1.00.016 CPU V1.21.00

Typical Installer Menu

Note: The Installer Menu header will vary depending on the TV you are setting up.

117 FACT DEFAULT 001

003 BAND/AFC 00X

Adjust the settings for these

Installer Menu items.

CHANNEL

OPTION

Use the TV setup menus to set the TV

features to the desired configuration

PICTURE

LOCK

for the end user.

AUDIO

INPUT

TIME

USB

(Continued on next page)

206-4200

Master TV Setup (Cont.)

(Continued from previous page)

3. (Optional) Run Auto Tuning.

Important: If you intend to use a USB memory device / .tlx file for cloning purposes, DO NOT run Auto Tuning. If you Teach a .tlx file with an auto-tuned/edited Channel Map to a Target TV, this will put the Target TV in FTG Mode via CPU. If you run Auto Tuning with the intension to clone the resulting Channel Map, you must use a USB memory device / .tll file or a clone programmer for this cloning purpose.

a) To search for all available analog and digital channels, go to the

Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

b) Use the Channel Edit option in the Channel Menu to edit the

channel lineup, as necessary, to include only free to guest (non-encrypted) channels.

• Add/delete channels per your system requirements.

• Use the Channel Label option in the Channel Menu to select the appropriate trademark/icon for each channel’s Channel-Time on-screen display. Icons are available for familiar channels, such as ABC, CBS, NBC, etc. Identiable labels (icons) should enable the end user to readily know what common networks are available.

Note: If you intend to clone the PTC and Installer Menu item 103 ATSC TUNE MODE is set for Physical Channel tuning (default and recommended setting), channels with minor channel numbers higher than 255 will not transfer correctly in step 5. If item 103 is set for Virtual Channel tuning and either the major or minor channel numbers are higher than 255, the channel(s) will not transfer correctly in step 5.

Note: If you intend to clone the PTC, you can add the channel icons in this step or as described in step 6. Also in step 6, you can add custom text labels for channels without icons.

4. Determine the next appropriate step according to the cloning method you intend to use.

• If using a USB memory device / .tll le or a clone programmer: Continue with step

5. You must perform this step to transfer the TV setup menu settings to the PTC in order to clone the PTC successfully.

• If using a .tlx le: Proceed to step 7 to verify the TV setup. (Steps 5 and 6 are not

applicable for .tlx les.)

Move

CHANNEL

Auto Tuning

Manual Tuning

Channel Edit

Channel Label

(Optional) Use Channel Menu options to run Auto Tuning, edit channels, and

select channel icons.

Enter

206-4200

(Continued on next page)

Master TV Setup (Cont.)

(Continued from previous page)

5. Transfer the TV setup menu settings to the commercial controller (PTC): 2-5-5 + MENU Mode

Important: This step is essential for successful cloning using a USB memory

device / .tll file or a clone programmer. Without this step, the PTC will not contain any of the TV setup menu settings.

a) After the TV channel lineup has been edited and channel label icons added, tune to

the channel (source) for which you wish to transfer TV setup menu settings.

Note: If you intend to use a clone programmer for cloning purposes, this must be either an analog channel or Aux input.

b) Enter the Installer Menu, and press 2-5-5 + MENU on the Installer Remote to

initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and then tunes through the channels in the channel lineup during the transfer. When the transfer is complete, the TV tunes back to the channel that was tuned before the transfer began.

Note: The maximum number of channels that can be transferred is 141. An attempt to transfer more than 141 channels will result in erratic TV tuning operation.

6. (Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode

Note: This step is applicable only if you intend to clone the PTC. 2-5-4

+ MENU Mode enables you to add/edit channel icons and custom text labels in the PTC once the Master TV Setup has been transferred as described in the previous step.

Enter the Installer Menu, and press 2-5-4 + MENU on the Installer Remote. Add/edit custom text labels and/or change icons for the Channel-Time on-screen displays (see 2-5-4 + MENU procedural information on page 23). Note that broadcast digital channels often already have a broadcaster generated label. When you are finished, press MENU to exit 2-5-4 + MENU Mode.

7. Verify the TV setup.

As applicable, verify that the channel lineup, channel icons, and custom

text labels are correct. Also, make sure the TV features are set per your requirements.

8. Lock the channel lineup.

Enter the Installer Menu. Set item 028 CH. OVERIDE to 000 and press ENTER to lock the channel lineup and restrict access to the TV setup menus. Press ENTER again to save your changes and exit the Installer Menu.*

The Master TV Setup is now ready to be copied to the predetermined cloning tool—a USB memory device (.tlx or .tll le) or a clone programmer. See cloning procedures in this document.

After verifying the TV Setup, set Installer

DIGITAL

STEREO SAP

MONO

19-3

WXYZ

Custom text label “WXYZ” created

in 2-5-4 + MENU Mode.

028 CH. OVERIDE 000

Menu item 028 CH. OVERIDE to 000.*

* This step prevents end users from

accessing channel settings (i.e., the Channel Menu will be inaccessible/ grayed out).

206-4200

Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.

Accessing the Installer Menu

1. Make sure the TV is ON.

2. Using an Installer Remote, press MENU repeatedly until the onscreen display of the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not in Pass-through Mode) no longer toggles, and then press 9-8-7-6 + ENTER to access the Installer Menu.

The Installer Menu opens with item 000 INSTALLER SEQ 000.

Note: If the password is not entered or registered correctly, you will see the message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu header. Once you re-enter the correct password (i.e., press 9-8-7-6 + ENTER), the Installer Menu will display.

Note: If the TV is in FTG Mode, the Installer Menu is accessible as readonly. Refer to pages 33 to 43 for information on FTG Mode configuration.

xxLD66xH PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 ASIC D27B PTC V1.00.014 CPU V1.17.00

Typical Installer Menu

Installer Menu

Using the Installer Menu

Refer to the table on pages 16 and 17 for an overview of the available Installer Menu items, including their item numbers, functions, value ranges, and default values.

Installer Menu items not relevant to this TV series are not present in the Installer Menu; therefore, some numbers are missing. For example, item 006 will not appear. In addition, items that are dependent on other Installer Menu item settings will not be initially accessible. For example, item 046 STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.

Navigation within the Installer Menu

Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items, or access an item directly by keying in the item number and then pressing MENU. For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.

Changing Installer Menu Settings

To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or enter a valid value directly. To save the new setting, press ENTER, or use the Up/Down arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will not be saved.

Exiting the Installer Menu and Activating Updates

After you have adjusted all required Installer Menu item settings, press ENTER once on the Installer Remote to save your changes; then, press ENTER again to exit the Installer Menu. Any changes you make will be stored in non-volatile memory.

Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control) settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from the Lock setup menu (see the Owner’s Manual for additional information), will now be disabled, and the individual Parental Control settings will be restored to default values.

206-4200

Installer Menu (Cont.)

Installer Menu Items 000 through 073

Item

Function Value Range Default Value Brief Description of Function and Comments

000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.

001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff.

002 AC ON 0 / 1 0 Set to 1 to enable Auto Turn ON when AC power is applied.

003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

004 STRT CHANNEL

005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.

007 STRT VOLUME 0 ~ 63, 255 255

008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.

009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.

010 MUTE DISABLE 0 / 1 0 Set to 1 to disable Mute Function.

011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.

015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.

016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.

017 ALARM 0 / 1 1 Set to 1 to enable Alarm.

020 FEATURE LEVEL 0 ~ 1, 16 ~ 24 1 Determines an additional IR code scheme to which the TV will respond.

021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip (Parental Control) functions.

022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip blocking hours.

023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting set before TV turned OFF.

028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.

029 OLD OCV 0 / 1 0 Set to 1 to change MPI operation to OCV.

030 ACK MASK 0 / 1 0 If set to 1, enables ACK feature of MPI.

031 POLL RATE 20 ~ 169 94 Selects poll rate for MPI.

032 TIMING PULSE 186 ~ 227 207 Sets baud rate for MPI.

034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.

035 COMPPORT EN. 0 / 1 1 Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1.

038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component Video 1 input jacks.

039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.

040 AUTO CAMPORT 0 / 1 1

046 STRT AUX SRCE 1 ~ 6, 255 6 Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).

047 AUX STATUS 0 / 1 0

053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.

069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.

070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Channel-Time display.

071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display.

073 CH NOT AVBLE 0 / 1 0

0 ~ 127, 253,

255

Channel tuned when TV is turned ON. (Set to 255 to tune to channel

tuned before TV turned OFF.)

Volume level when TV is turned ON. (Set to 255 to use volume level

before TV turned OFF.)

Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE

cannot be set to 2.

Set to 1 for MPI Aux source to be reported as a channel number instead of

Channel 0.

If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message is displayed if user direct tunes a channel that is not in the favorite channel list.

206-4200

Installer Menu Items 075 through 122

Installer Menu (Cont.)

Item

Function Value Range Default Value Brief Description of Function and Comments

075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.

078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.

079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.

080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.

081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.

082 CHKSM ERROR 0 / 1 1 If set to 1, enforces rigid MPI checksum.

083 HANDSHK TIME 0 ~ 5 5

084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.

087 REAR RGB EN.

088 EN NOISE MUTE 0 / 1 1 If set to 1, audio is muted if no signal is present.

090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.

091 YPrPb2 EN 0 / 1 1 Set to 1 to enable HDMI 2 input.

093 RJP AVAILABLE 0, 1, 2, 5, 6 0

094 SAP MENU EN 0 / 1 1

096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.

098 PRO:CENTRIC

099 BACK LIGHTING

102 ATSC BAND 0 ~ 4 4 Selects ATSC band.

103 ATSC TUNE MODE 0 / 1 1 Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.

104 START MINOR CH 0 ~ 255 0 Selects Minor Start Channel. Set to 0 for NTSC.

106 ASP RATIO LOCK 0 / 1 0

116 VIDEO MUTE EN 0 / 1 0 Set to 0 for Normal. Set to 1 for Blank.

117 FACT DEFAULT 0 / 1 0 Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.

118 POWER SAVINGS 1 / 3 3

119 DATA CHANNEL 0 ~ 135, 253 0

121 P:C RF WAKE HR 0 ~ 23, 128 128

122 P:C RF WAKE MN 0 ~ 59 0

0 / 1 / 17

0 ~ 2

1 ~ 100, 101 ~

200, 201, 202, 255

202

Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.

Relaxes MPI timing to be compatible with PC-based Windows-

controlled systems.

Set to 1 to enable RGB input. Set to 17 for Auto Configure.

Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See

detailed descriptions.)

Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on

Function Menu.

Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for

GEM (Java Application) Mode.

Sets the level of the TV picture back lighting. (See detailed descriptions.)

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on

power cycle.

Set to 3 (default—b-LAN module only powered when TV is turned ON), or

set to 1 (b-LAN module is always powered). (See detailed descriptions.)

Set to 0 to disable. Set to the RF channel number of the data channel for

Pro:Centric or TV E-Z Installation data. (See detailed descriptions.)

Sets the hour for Wake On RF. The value “128” is displayed as “OFF.” Directly

entering 128 turns the Wake On RF feature OFF.

Sets the minute for Wake On RF.

206-4200

Caution: Installer Menu settings may affect options available from the TV setup menus or the Function Menu.

Installer Menu (Cont.)

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Species entry sequence to the Installer Menu.

0 = 9876 1 = 4321 2 = 1478 3 = 3698

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain ON, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, this allows the TV to turn ON when AC power is applied. Pressing the ON button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is the default (OFF), and 1 is ON.

Note: If set to 1 (ON), the TV does not respond to ON/OFF commands from either the remote or the display panel, and the SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are four possible settings for this option:

0 = Broadcast 1 = CATV (default) 2 = HRC 3 = IRC

If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here, and add the channels using the Channel Edit option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial Major Start Channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned ON. Setting this item to 255 causes the last channel viewed when the TV was turned OFF, to be the tuned to channel when the TV is turned ON again.

Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

Note: The IP Start Channel shown below can only be set in the FTG File Manager, which is used to congure TV CPUs for FTG Mode. The same applies for 2-byte tuning ranges (128 ~ 135 for Physical 2-byte tuning and 128~999 for Virtual 2-byte tuning). This means that these values, if set, will only be visible in the readonly Installer Menu when the TV is in FTG Mode via CPU. The read-only display also will show additional information about the channel, for example, the IP address and port number, etc.

0 = Aux 127 = Map to Channel 4 1 ~ 125 = Major Ch. # 253 = IP Start Channel 126 = Map to Channel 3 255 = Last Channel

005 - CHAN LOCK (Channel Lock)

Channel Lock is ideal if the system must always be on the same channel. Changing channels with the Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with item 004 STRT CHANNEL where the Start Channel may, for example, be set to 3 or 4. If the Start Channel is 3, then the TV will remain locked on channel 3.

NOTE: For items 007, 008, and 009 For legacy reasons, the scale used is 0 – 63. The PTC software will translate this to the 0 – 100 scale used by the TV.

To translate a TV volume level to the Installer Menu value, use the following formula:

Installer Value = TV Value x 63 100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned ON. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned OFF; at turn ON, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63. Use the Left/Right arrow keys to change values. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV.

Note: The minimum volume level cannot have a value setting higher than the maximum volume level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Use the Left/Right arrow keys to change values. It may be best to set the same value on every TV.

Note: The maximum volume level cannot have a value setting lower than the minimum volume level (described above).

206-4200

Installer Menu (Cont.)

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, KEY DEFEAT prevents the end user from accessing the on-screen menu(s) from the display panel—MENU, ENTER, and menu navigation keys do not function. If set to 0, those keys do function.

Note: Users can always access the menu(s) by pressing MENU on the remote.

015 - SLEEP TIMER

If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers)

If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers.

Note: Clock must be set in order for timers to be used.

017 - ALARM

Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.

Note: Clock must be set before the Alarm function will work.

020 - FEATURE LEVEL

Determines an additional IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on “bed number” in a multi-TV single room installation. First determine the IR mode; then select the bed number.

IR Mode Bed # Values

Legacy (Hospital) 1 – 2 0 – 1

Multi-code Remote 1 – 9 16 – 24

Note: For further information, see documentation for the accessory package that includes the multi-code remote.

021 - V-CHIP (Parental Control) Set to 1 to activate V-Chip (Parental Control) and have it available to the end user to lter and control or otherwise restrict programming content that can appear. Set to 0 to turn the V-Chip feature Off (not available to user); no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

Note: This item is not available in the Installer Menu unless item 084 PERMANENT BLK is set to 0.

023 - CAPTION LOCK

If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting congured before the TV was turned OFF when the TV is turned ON.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.

029 - OLD OCV (On Command Video™)

Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK

MPI Communication Parameter. When set to 1, enables ACK feature of MPI.

031 - POLL RATE

MPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI.

032 - TIMING PULSE

MPI Communication Parameter. Sets baud rate for MPI. Step size of 4.3 uS. Changing from default may affect communication via MPI.

034 - CAMPORT EN. (Camera Port Enable)

Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

035 - COMPPORT EN. (Computer Port Enable)

Enable/disable TV display panel HDMI 1 input jack. Set to 0 to disable HDMI 1. Set to 1 to enable HDMI 1.

Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.

040 - AUTO CAMPORT

Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection. If set to 1, STRT AUX SRCE cannot be set to 2.

Note: If set to 1, item 093 RJP AVAILABLE is automatically set to 0.

206-4200

Installer Menu (Cont.)

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting Aux source. When turned ON, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.

If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO CAMPORT is set to 0: 1 = Video 1 4 = RGB 255 = Last Aux 2 = Video 2 5 = HDMI 2 3 = HDMI 1 6 = Component

If item 093 RJP AVAILABLE is set to 1: 2 = Video 2 5 = HDMI 2 6 = Component

If item 040 AUTO CAMPORT is set to 1: 1 = Video 1 4 = RGB 6 = Component 3 = HDMI 1 5 = HDMI 2

Note: This item is not available in the Installer Menu unless item 004 STRT CHANNEL is set to 0.

047 - AUX STATUS

Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identication change. Controls MPI status channel response for Aux inputs.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display; Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAILABLE” message is displayed when a user direct tunes a channel that is not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automatically tunes to the specied Start Channel.

Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 255.

078 - UPN MSB (UPN Most Signicant Byte)

User programmable number, most signicant byte readable by MPI command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Signicant Byte-1)

User programmable number, most signicant byte-1 readable by MPI command. Note: Not linked to serial number.

080 - UPN MSB-2 (UPN Most Signicant Byte-2)

User programmable number, most signicant byte-2 readable by MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Signicant Byte)

User programmable number, least signicant byte readable by MPI command. Note: Not linked to serial number.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Set according to Color Chart:

0 = Black 3 = Cyan 6 = Yellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet

Note: If foreground color and background color are the same, the menu background will be transparent.

Note: Applies only to “Channel Not Available” message if item 073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR. CH-TIME and 071 BCK. CH-TIME are not available in the Installer Menu when item 069 EN. CH-T COL. is set to 0.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

See description for item 070 FOR. CH-TIME above. The color chart is the same for both items.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PCbased Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specied hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a onetime automatic conguration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed.

206-4200

Installer Menu (Cont.)

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes when no signal is present.

090 - KEY LOCK

If set to 1, display panel Channel, Volume, and Caption buttons are disabled, Power button remains enabled. If set to 0, Channel, Volume, Caption, and Power buttons are all enabled.

091 - YPrPb2 EN. (HDMI2 Enable)

Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable display panel HDMI 2 input.

093 - RJP AVAILABLE (Remote Jack Pack Available)

• 0 = Remote jack pack is not available or disabled.

• 1 = Legacy Model RJPs: HDMI Mode

Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

• 2 = Legacy Model RJPs: DVI Mode

Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via a separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

• 5 = Scaler Model RJPs: HDMI Mode

Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

• 6 = Scaler Model RJPs: DVI Mode

Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

Notes:

See Reference section, “RJP Model List and Input Auto-sensing Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040 AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6 allow the lodge staff to customize each TV’s RJP setup based on customer requirements.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function Menu, if Function Menu is available (i.e., TV is not in Pass-through Mode). Set to 0 to disable SAP feature on Function Menu, if Function Menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up.

• Set to 0 for Set By System.

• Set to 1 for 4:3.

• Set to 2 for 16:9 (Factory Default).

• Set to 3 for Just Scan.

• Set to 4 for Zoom.

Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0.

098 - PRO:CENTRIC

Selects the Pro:Centric Application Mode. Set to 0 (default) to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.

Note: This item is not available in the Installer Menu when item 119 DATA CHANNEL is set to 0.

Note: When both Pro:Centric items (098 PRO:CENTRIC and 119 DATA CHANNEL) are set, once you exit the Installer Menu, the Function Menu will be available to end users instead of the TV setup menus. Also, only the Learn From TV (TLX) option will be available from the USB Download Menu; the Teach to TV option will not.

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 202.

• 1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

• 101 - 200 Dynamic Back Lighting

(101 = Dimmest picture, 200 = Brightest picture)

• 201 Automatic Static Back Lighting

• 202 Automatic Dynamic Back Lighting

If set between 101 and 200, the TV automatically controls back lighting depending upon the picture level of the current program. If set to 201, the TV automatically controls back lighting depending upon external spectral sensitivity. If set to 202, the TV automatically controls back lighting depending upon external spectral sensitivity and the picture level of the current program. If set to 255, back lighting is controlled via the Picture settings in the TV’s setup menus.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals: 0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan.

206-4200

+ 47 hidden pages