LG 26LT640H-TA, 32LT640E-TA, 26LT640E-TA, 32LT640H-TA, 37LT640H-TA Owner's Manual
...
www.lg.com
OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set and retain it
for future reference.
LT64**
ENG
ENGLISH
2
TABLE OF CONTENTS
21 MAINTENANCE
21 Cleaning your TV
21 - Screen, frame, cabinet and stand
21 - Power cord
21 TROUBLESHOOTING
22 CAUTION FOR USING
EZSIGN 2.0
23 SPECIFICATIONS
26 IR CODES
27 EXTERNAL CONTROL
DEVICE SETUP
27 RS-232C Setup
27 Type of connector;
D-Sub 9-Pin Male
27 RS-232C Configurations
28 Communication Parameters
28 Command reference list
29 Transmission / Receiving Protocol
TABLE OF CONTENTS
3 LICENSES
3 OPEN SOURCE SOFTWARE
NOTICE
4 INSTALLATION PROCEDURE
4 ASSEMBLING AND
PREPARING
4 Unpacking
6 Optional Extras (Only
26/32/37/42/47LT640E)
7 Parts and buttons
8 Lifting and moving the TV
9 Setting up the TV
9 - Attaching the stand
11 - Mounting on a table
12 - Mounting on a wall
14 - Tidying cables
15 MAKING CONNECTIONS
15 Adapter connection
15 Antenna connection
16 HDMI connection
16 DVI to HDMI connection
17 Component connection
17 RGB-PC connection
18 Composit connection
18 Audio connection
18 - Digital optical audio connection
19 Speaker output SETUP
19 Volume control port
19 Headphone connection
19 USB connection
20 REMOTE CONTROL
WARNING
y
If you ignore the warning message, you may
be seriously injured or there is a possibility
of accident or death.
CAUTION
y
If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
y
The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
3
LICENSES / OPEN SOURCE SOFTWARE NOTICE
ENGENGLISH
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC
.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
y
Image shown may differ from your TV.
y
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
y
The available menus and options may differ from the input source or product model that you are
using.
y
New features may be added to this TV in the future.
y
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
be turned off if it will not be watched for some time, as this will reduce energy consumption.
y
The energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1
Open the package and make sure all the accessories are included.
2
Attach the stand to the TV set.
3
Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
CAUTION
y
Do not use any unapproved items to ensure the safety and product life span.
y
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
y
Some models have a thin film attached on to the screen and this must not be removed.
NOTE
y
The items supplied with your product may vary depending on the model.
y
Product specifications or contents of this manual may be changed without prior notice due to upgrade
of product functions.
y
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
A
A
B
*A 10 mm
*B 18 mm
5
ASSEMBLING AND PREPARING
ENGENGLISH
Remote control,
Batteries (AAA)
(See p.20)
Owner’s manual
Cable holder
(Depending on model)
(See p.14)
Power cord
Stand Screws
8 EA, M4 x 12
(Only 26LT64
**
)
(See p.9)
Stand Screws
8 EA, M4 x 14
(Only 32/37/42/47LT64
**
)
(See p.10)
Desk-mount Screw
1 EA, M4 x 20
(Only 32/37/42/47LT64**)
(See p.11)
DC Adapter
(Only 26LT64**)
(See p.15)
Power Cord holder
(Only 32/37/42/47LT64**)
(See p.14)
Protection cover
(Only 32/37/42/47LT64**)
(See p.13)
Stand body / Stand base
(Only 26LT64**)
(See p.9)
Stand body / Stand base
(Only 32/37/42/47LT64**)
(See p.10)
or
Isolator
(Depending on model)
(See p. 6)
EzSign 2.0 Editor CD
(Depending on model)
FREEZE
RATIO
L/R SELECT
ENTER
BACK
EXIT
Q.MENU
INFO
MENU
CHVOL
P
A
G
E
FAV
3D
MUTE
1 2 3
4 5 6
7 809
MARK
LIST
FLASHBK
ENERGY
SAVING
TV
AV MODE
INPUT
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
y
Antenna Isolator Installation Guide
- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
- Before starting, be sure that the TV antenna is connected.
ANTENNA/
CABLE IN
Cable / Antenna
Wall
Isolator
1. Connect to TV.
2. Connect to Set-Top box.
or
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a re hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
Optional Extras (Only 26/32/37/42/47LT640E)
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AN-WF100
Wireless LAN for Broadband/
DLNA Adaptor
7
ASSEMBLING AND PREPARING
ENGENGLISH
Parts and buttons
Button Description
∨∧
Scrolls through the saved programmes.
- +
Adjusts the volume level.
Turns the power on or off.
Speakers
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION -menu.)
Remote control sensor
Clock LED
Screen
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
y
It is recommended to move the TV in the box
or packing material that the TV originally came
in.
y
Before moving or lifting the TV, disconnect the
power cord and all cables.
y
When holding the TV, the screen should face
away from you to avoid damage.
y
Hold the top and bottom of the TV frame rmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
y
When transporting a large TV, there should be
at least 2 people.
y
When transporting the TV by hand, hold the TV
as shown in the following illustration.
y
When transporting the TV, do not expose the
TV to jolts or excessive vibration.
y
When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
CAUTION
y
Avoid touching the screen at all times, as this
may result in damage to the screen.
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
9
ASSEMBLING AND PREPARING
ENGENGLISH
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
(Only 26LT64**)
Front
Stand Body
Stand Base
M4X20
Top View
1
M4 x 12
4 EA
2
3
M4 x 12
4 EA
10
ASSEMBLING AND PREPARING
ENG
ENGLISH
(Only 32/37/42/47LT64**)
Front
1
Stand Body
Stand Base
3
2
M4 x 14
4 EA
CAUTION
y
When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or at surface to protect the
screen from scratches.
y
Make sure that the screws are inserted
correctly and fastened securely. If they are
not fastened securely enough, the TV may
tilt forward after being installed.
Do not use too much force and over tighten
the screws; otherwise screw may be
damaged and not tighten correctly.
NOTE
y
Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
4 EA
M4 x 14
M4X20
Top View
11
ASSEMBLING AND PREPARING
ENGENGLISH
Mounting on a table
1
Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
2
Connect the power cord to a wall outlet.
Securing the TV to a table
(Only 32/37/42/47LT64**)
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and
tighten the supplied screw on the rear of the stand.
Adjusting the angle of the TV to suit view
Swivel 90 degrees to the left or right and adjust the
angle of the TV to suit your view.
10 cm
10 cm
10 cm
10 cm
CAUTION
y
Do not place the TV near or on sources
of heat, as this may result in re or other
damage.
WARNING
y
To prevent TV from falling over, the TV
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause injury.
9090
CAUTION
y
When adjusting the angle of the product,
watch out for your ngers.
»Personal injury may occur if hands or
fingers are pinched. If the product is tilted
too much, it may fall, causing damage or
injury.
Attaching the TV to a table
Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the product.
(Only 32/37/42/47LT64**)
Screws: M4 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M4 x 20
(not provided as parts of the product)
4-Screws
Stand
Table
Loading...