B-7 - Digital optical audio connection
B-8 USB connection
B-9 CI module connection
B-10 Headphone connection
B-11 Euro Scart connection
COMMON
LANGUAGE
B-13 SPECIFICATIONS
COMMON
Page 5
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
LA62**, LA64**, LA66**, LN57**-ZE/ZK
SETTING UP THE TV
A-3
1
4 EA
M4 x 14
Stand Body
Stand Base
2
(Only LA62**, LN57**-ZE/ZK)
Front
(Only LA62**, LN57**-ZE/ZK)
3
(Only LA64**, LA66**)
M4 x 14
4 EA
(Only LA64**, LA66**)
M4 x 14
4 EA
Page 6
SETTING UP THE TV
A-4
LA69**, LA74**
1
2
3
Stand Base
M4 x 20
4EA
Page 7
LN57**-ZA
1
2
Stand Base
Stand Body
3EA
P5 x 25
SETTING UP THE TV
CAUTION
yWhen attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect the
screen from scratches.
yMake sure that the screws are inserted
correctly and fastened securely. (If they are
not fastened securely enough, the TV may
tilt forward after being installed.)
Do not use too much force and over tighten
the screws; otherwise screw may be
damaged and not tighten correctly.
NOTE
yRemoving the protective film (from the
bottom)
(Depending on model)
Protective film is temporarily attached to
prevent the surface of the product from
being damaged during delivery.
Once the TV has been installed, please
remove the protective film on the bottom of
the unit as shown in the figure.
A-5
3
M4 x 14
yRemove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
4EA
Page 8
SETTING UP THE TV
⨲㘶ᖂ2
㏪ⱞ⋾#Ɐᴏ
A-6
Tidying cables
1 Gather and bind the cables with the Cable
Holder and the Cable Management.
2 Fix the Cable Management rmly to the TV.
(Only LA62**, LA64**, LA66**, LN57**-ZE/ZK)
Cable Holder
Cable Management
(Only LA69**, LA74**)
Cable Holder
(Only LN57**-ZA)
1 Gather and bind the cables with the Cable
Holder.
Cable Holder
CAUTION
yDo not move the TV by holding the cable
holders, as the cable holders may break,
and injuries and damage to the TV may
occur.
Cable Management
Page 9
OWNER’S MANUAL
LED TV
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
Page 10
TABLE OF CONTENTS
2
ENGLISH
ENG
TABLE OF CONTENTS
3 LICENSES
3 OPEN SOURCE SOFTWARE NOTICE
4 SAFETY INSTRUCTIONS
10 - Viewing 3D Imaging (Only 3D models)
12 INSTALLATION PROCEDURE
12 ASSEMBLING AND PREPARING
12 Unpacking
16 Separate purchase
17 Parts and buttons
18 Lifting and moving the TV
19 Mounting on a table
21 Mounting on a wall
23 REMOTE CONTROL
25 MAGIC REMOTE CONTROL
FUNCTIONS
26 Registering Magic Remote Control
26 How to use Magic Remote Control
26 Precautions to Take when Using the Magic
Remote Control
27 USING THE USER GUIDE
28 MAINTENANCE
28 Cleaning your TV
28 - Screen, frame, cabinet and stand
28 - Power cord
28 TROUBLESHOOTING
29 EXTERNAL CONTROL DEVICE
SETUP
29 SPECIFICATIONS
WARNING
yIf you ignore the warning message, you may
be seriously injured or there is a possibility
of accident or death.
CAUTION
yIf you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
yThe note helps you understand and use
the product safely. Please read the note
carefully before using the product.
Page 11
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI logo
are trademarks or registered trademarks of HDMI Licensing LLC in the United States
and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an ofcial DivX Certied® device that plays
DivX video. Visit divx.com for more information and software tools to convert your
les into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certied® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
ENGENGLISH
“DivX Certied® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certied® and associated logos are trademarks of Rovi Corporation or
its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
Page 12
SAFETY INSTRUCTIONS
4
ENGLISH
ENG
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/or remote control in the following environments:
y
- A location exposed to direct sunlight
- An area with high humidity such as a bathroom
- Near any heat source such as stoves and other devices that produce heat
- Near kitchen counters or humidifiers where they can easily be exposed to steam
or oil
- An area exposed to rain or wind
- Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product deformation.
Do not place the product where it might be exposed to dust.
y
This may cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains electric supply.
y
This plug must remain readily attached and operable when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or
y
covered with dust, dry the power plug completely or wipe dust off.
You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with Grounded
y
earth pin. (Except for devices which are not grounded on earth.) Otherwise
possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not secured
y
completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects such as a
y
heater.
This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
y
Otherwise, this may result in fire or electric shock.
Bend antenna cable between inside and outside building to prevent rain from
y
flowing in.
This may cause water damaged inside the Product and could give an electric
shock.
When mounting TV onto wall make sure to neatly install and isolate cabling from
y
rear of TV as to not create possibility of electric shock /fire hazard.
Page 13
Desiccant
SAFETY INSTRUCTIONS
Do not plug too many electrical devices into a single multiple electrical outlet.
y
Otherwise, this may result in fire due to over-heating.
Do not drop the product or let it fall over when connecting external devices.
y
Otherwise, this may result in injury or damage to the product.
Keep the anti-moisture packing material or vinyl packing out of the reach of
y
children.
Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the
patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause
suffocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the TV.
y
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not consume
y
them.
Please seek Doctor- Medical Attention immediately if child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/cutlery/
y
screwdriver) between power cable plug and input Wall Socket while it is connected
to the input terminal on the wall. Additionally, do not touch the power cable right
after plugging into the wall input terminal. You may be electrocuted.
(Depending on model)
Do not put or store inflammable substances near the product.
y
There is a danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
5
ENGENGLISH
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the
y
product, or inflammable objects such as paper and matches. Children must pay
particular attention.
Electrical shock, fire or injury can occur. If a foreign object is dropped into the
product, unplug the power cord and contact the service centre.
Do not spray water on the product or scrub with an inflammable substance (thinner
y
or benzene). Fire or electric shock accident can occur.
Do not allow any impact, shock or any objects to fall into the unit, and do not drop
y
anything onto the screen.
You may be injured or the product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
y
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the windows and
y
ventilate.
It may cause a fire or a burn by a spark.
Page 14
SAFETY INSTRUCTIONS
6
ENGLISH
ENG
Do not disassemble, repair or modify the product at your own discretion.
y
Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and contact your local
y
service centre.
- The product has been impacted by shock
- The product has been damaged
- Foreign objects have entered the product
- The product produced smoke or a strange smell
This may result in fire or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the TV for a
y
long period of time.
Accumulated dust can cause fire hazard and insulation deterioration can cause
electric leakage/shock/fire.
Apparatus shall not be exposed to dripping or splashing and no objects filled with
y
liquids, such as vases, shall be placed on the apparatus.
Page 15
SAFETY INSTRUCTIONS
7
CAUTION
Install the product where no radio wave occurs.
y
There should be enough distance between an outside antenna and power lines to
y
keep the former from touching the latter even when the antenna falls.
This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined surfaces.
y
Also avoid places where there is vibration or where the product cannot be fully
supported.
Otherwise, the product may fall or flip over, which may cause injury or damage to
the product.
If you install the TV on a stand, you need to take actions to prevent the product
y
from overturning. Otherwise, the product may fall over, which may cause injury.
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional
y
parts) to the back of the product. When you install the set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
y
When installing the antenna, consult with a qualified service technician. If not
y
installed by a qualified technician, this may create a fire hazard or an electric shock
hazard.
ENGENGLISH
We recommend that you maintain a distance of at least 2 to 7 times the diagonal
y
screen size when watching TV.
If you watch TV for a long period of time, this may cause blurred vision.
Only use the specified type of battery.
y
This could cause damage to the remote control.
Do not mix new batteries with old batteries.
y
This may cause the batteries to overheat and leak.
Batteries should not be exposed to excessive heat.eg keep away from direct Sunlight , open
y
fireplace and electric heaters .
Do not place non-rechargeable batteries in charging device.
y
Make sure there are no objects between the remote control and its sensor.
y
Signal from Remote Control can be interrupted due to external/internal lighting eg
y
Sunlight, fluorescent lighting.
If this occurs turn off lighting or darken viewing area.
When connecting external devices such as video game consoles, make sure the
y
connecting cables are long enough.
Otherwise, the product may fall over, which may cause injury or damage the
product.
Page 16
SAFETY INSTRUCTIONS
8
ENGLISH
ENG
Do not turn the product On/Off by plugging-in or unplugging the power plug to the
y
wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the product from
y
overheating.
- The distance between the product and the wall should be more than 10 cm.
- Do not install the product in a place with no ventilation (e.g., on a bookshelf or in
a cupboard).
- Do not install the product on a carpet or cushion.
- Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Take care not to touch the ventilation openings when watching the TV for long
y
periods as the ventilation openings may become hot. This does not affect the
operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance indicates damage or
y
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact
replacement part by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet.
y
This may cause a fire hazard.
Protect the power cord from physical or mechanical abuse, such as being twisted,
y
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such as nail,
y
pencil or pen, or make a scratch on it, as it may cause damage to screen.
Avoid touching the screen or holding your finger(s) against it for long periods of
y
time. Doing so may produce some temporary or permanent distortion/damage to
screen.
When cleaning the product and its components, unplug the power first and wipe it
y
with a soft cloth. Applying excessive force may cause scratches or discolouration.
Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or
industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the
product and its panel.
Otherwise, this may result in fire, electric shock or product damage (deformation,
corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
y
source even if you turn off this unit by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at the plug.
y
Don’t pull at the cord to unplug the power cord from the power board, as this could
be hazardous.
When moving the product, make sure you turn the power off first. Then, unplug the
y
power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire hazard or
cause electric shock.
Page 17
SAFETY INSTRUCTIONS
When moving or unpacking the product, work in pairs because the product is
y
heavy.
Otherwise, this may result in injury.
Contact the service centre once a year to clean the internal parts of the product.
y
Accumulated dust can cause mechanical failure.
Refer all servicing to qualified service personnel. Servicing is required when the
y
apparatus has been damaged in any way, such as power supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
If the product feels cold to the touch, there may be a small “flicker” when it is turned
y
on. This is normal, there is nothing wrong with product.
The panel is a high technology display product with resolution of two million to six
y
million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and
does not affect the performance and reliability of the product.
This phenomenon also occurs in third-party products and is not subject to
exchange or refund.
You may find different brightness and color of the panel depending on your viewing
y
position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not related with
the product performance, and it is not malfunction.
9
ENGENGLISH
Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video
y
game) for a prolonged time may cause damage to the screen, resulting in retention of the image,
which is known as image sticking. The warranty does not cover the product for image sticking.
Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours
for LCD, 1 or more hours for Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of
the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
Generated Sound
y
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by
plastic thermal contraction due to tempera-ture and humidity. This noise is common for products
where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a large amount of current to operate a
product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
Page 18
SAFETY INSTRUCTIONS
10
ENGLISH
ENG
Viewing 3D Imaging (Only 3D models)
WARNING
Viewing Environment
yViewing Time
- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long
period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
ySome users may experience a seizure or other abnormal symptoms when they are exposed to a
ashing light or particular pattern from 3D contents.
yDo not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as epilepsy,
cardiac disorder, or blood pressure disease, etc.
y3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly. Double
images or discomfort in viewing may be experienced.
yIf you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble
sensing depth and easily feel fatigue due to double images. It is advised to take frequent breaks than
the average adult.
yIf your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or refraining from watching 3D contents
yDo not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
yWhen these symptoms are experienced, stop using/watching 3D contents and get enough rest until the
symptom subsides.
- Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain,
dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue.
Page 19
SAFETY INSTRUCTIONS
11
CAUTION
Viewing Environment
y Viewing Distance
- Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you
feel discomfort in viewing 3D contents, move further away from the TV.
Viewing Age
yInfants/Children
- Usage/ Viewing 3D contents for children under the age of 5 are prohibited.
- Children under the age of 10 may overreact and become overly excited because their vision is in
development (for example: trying to touch the screen or trying to jump into it. Special monitoring
and extra attention is required for children watching 3D contents.
- Children have greater binocular disparity of 3D presentations than adults because the distance
between the eyes is shorter than that of adults. Therefore they will perceive more stereoscopic
depth compared to adults for the same 3D image.
yTeenagers
- Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D
contents. Advise them to refrain from watching 3D contens for a long time when they are tired.
yElderly
- The elderly may perceive less 3D effect compared to the young. Do not sit closer to the TV than the
recommended distance.
ENGENGLISH
Cautions when using the 3D glasses
y Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
y Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
y Using modied 3D glasses may cause eye strain or image distortion.
y Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
y The 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth when wiping
the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them with
chemicals.
Page 20
ENGLISH
<
<
ENG
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
12
NOTE
yImage shown may differ from your TV.
yYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yThe available menus and options may differ from the input source or product model that you are
using.
yNew features may be added to this TV in the future.
yThe TV can be placed in standby mode in order to reduce the power consumption. And the TV should
be turned off if it will not be watched for some time, as this will reduce energy consumption.
yThe energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
4 Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yDo not use any unapproved items to ensure the safety and product life span.
yAny damage or injuries caused by using unapproved items are not covered by the warranty.
ySome models have a thin film attached on to the screen and this must not be removed.
NOTE
yThe items supplied with your product may vary depending on the model.
yProduct specifications or contents of this manual may be changed without prior notice due to upgrade
of product functions.
yFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
A
B
*A
10 mm
=
18 mm
*B
A
=
Page 21
ASSEMBLING AND PREPARING
P
123
13
AV MODE
INPUT
ENERGY
TV
SAVING
123
456
7809
FLASHBK
LIST
MARK
FAV
PAG
3D
CHVOL
E
MUTE
INFO
MENU
Q.MENU
ENTER
EXIT
BACK
L/R SELECT
FREEZE
RATIO
Remote control and
batteries (AAA)
(Only LA62**, LA64**, ,
LN570*, LN575*, LN577*)
(See p. 23, 24)
Magic Remote Control,
Batteries (AA)
(Only LA66**, LA69**,
LA74**, LN578*)
(See p. 25)
ENGENGLISH
Wi-Fi Dongle
Owner’s manual
(Depending on model)
Cinema 3D Glasses
The number of 3D glasses
may differ depending on
the model or country.
(Depending on model)
Dual play glasses
(Depending on model)
Cable Holder
(Depending on model)
(See p. A-6)
Power Cord
(Depending on model)
Stand Screws
M4 x 14
(8 EA: Only LN57**-ZE/ZK,
LA62**, LA64**, LA66**)
(4 EA: Only LN57**-ZA)
(See p. A-3,A-5)
Stand Screws
M4 x 20
(4 EA: Only LA69**,
LA74**)
(See p. A-4)
Stand Screws
3 EA, P5 x 25
(Only LN57**-ZA)
(See p.A-5)
Desk-mount Cable
2 EA (Only
32/39/42/47/50LN57**-ZE/
ZK, 32/39/42/47/50LA62**,
32/42/47/50LA64**,
32/42/47/50LA66**)
(See p. 19)
Bracket Screw
2 EA, M4 x 8
(Only 32/39/42LN57**ZE/ZK, 32/39/42LA62**,
32/42LA64**,32/42LA66**)
(See p. 19)
Desk-mount Screw
(1 EA : Only
32/39/42/47/50/60LN57**ZA)
(2 EA :Only
32/39/42/47/50LN57**-ZE/
ZK, 32/39/42/47/50LA62**,
32/42/47/50LA64**,
32/42/47/50LA66**)
(See p. 19)
Bracket Screw
2 EA, P4 x 8
(Only 47/50LN57**ZE/ZK,47/50LA62**,
47/50LA64**,47/50LA66**)
(See p. 19)
Wall mount inner spacers
4 EA
(Only LA64**)
(See p. 22)
Page 22
ENGLISH
ENG
ASSEMBLING AND PREPARING
14
Tag On
Tag On
(Depending on model)
Stand Body / Stand Base
(Only LN57**-ZE/ZK,
LA62**, LA64** , LA66**)
(See p.A-3)
Stand Body / Stand Base
(Only LN57**-ZA)
(See p.A-5)
or
Isolator
(Depending on model)
(See p. 15)
Stand Base
(Only LA69**, LA74** )
(See p.A-4)
LG Audio device
(Depending on model)
Page 23
ASSEMBLING AND PREPARING
15
NOTE
yAntenna Isolator Installation Guide
- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
- Before starting, be sure that the TV antenna is connected.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains connection
or through other equipment with a connection to protective earthing - and to a cable distribution system
using coaxial cable, may in some circumstances create a re hazard. Connection to a cable distribution
system has therefore to be provided through a device providing electrical isolation below a certain
frequency range (galvanic isolator, see EN 60728-11)”
1. Connect to TV.
2. Connect to Set-Top box.
ENGENGLISH
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
Page 24
ASSEMBLING AND PREPARING
P
123
16
ENGLISH
ENG
Separate purchase
(Depending on model)
Separate purchase items can be changed or modied for quality improvement without any notication.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***DP
Dual play glasses
AN-WF100
Wi-Fi Dongle
AG-F***
Cinema 3D Glasses
AN-VC4**
Video call camera
AN-MR400
Magic Remote
LG Audio device
Tag On
Tag on
Compatibility
AG-F***DP
Dual play glasses
AG-F***
Cinema 3D Glasses
AN-MR400
Magic Remote
AN-WF100
Wi-Fi Dongle
AN-VC4**
Video call camera
LG Audio device
Tag On
LN57**
••
•
(Depending on model)
••
•
(Depending on model)
•
(Depending on model)
LA62**, LA64**,
LA66**, LA69**, LA74**
•
(Depending on model)
•
•
•
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
Page 25
ASSEMBLING AND PREPARING
H
H
H
SETTINGS
INPUT
OK
SETTINGS
INPUT
OK
SETTINGS
INPUT
OK
17
Parts and buttons
A type : LA62**, LA64**, LA66**,
LN57**-ZE/ZK
Screen
Speakers
Remote control sensor
LG Logo Light (Only LA64**, LA66**)
Power Indicator (Only LA62**, LN57**-ZE/ZK)
C type : 60LA74**
Screen
Buttons
OK
SETTINGS
INPUT
Buttons
B type : LA69**, 42/47/55LA74**
Screen
Remote control sensor
LG Logo Light
D type : LN57**-ZA
Screen
ENGENGLISH
Buttons
Speakers
Buttons
Speakers
NOTE
yYou can set the
Speakers
Remote control sensor
LG Logo Light
ButtonDescription
Scrolls through the saved programmes.
Adjusts the volume level.
Selects the highlighted menu option or confirms an input.
S
Accesses the main menu, or saves your input and exits the menus.
Changes the input source.
Turns the power on or off.
LG Logo Light
to on or off by selecting OPTION in the main menus.(Depending on model)
Remote control sensor
Power Indicator
Page 26
ASSEMBLING AND PREPARING
18
ENGLISH
ENG
Lifting and moving the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
CAUTION
yAvoid touching the screen at all times, as
this may result in damage to the screen.
yIt is recommended to move the TV in the box
or packing material that the TV originally came
in.
yBefore moving or lifting the TV, disconnect the
power cord and all cables.
yWhen holding the TV, the screen should face
away from you to avoid damage.
yWhen transporting a large TV, there should be
at least 2 people.
yWhen transporting the TV by hand, hold the TV
as shown in the following illustration.
yWhen transporting the TV, do not expose the
TV to jolts or excessive vibration.
yWhen transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yDo not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
yHold the top and bottom of the TV frame rmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
Page 27
ASSEMBLING AND PREPARING
19
Mounting on a table
1 Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
yDo not place the TV near or on sources
of heat, as this may result in fire or other
damage.
10 cm
10 cm
Securing the TV to a table
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
To secure the TV to a table, insert and tighten the
supplied screw on the rear of the stand.
(Only 32/39/42/47/50/60LN57**-ZA)
Using the Kensington security system (This feature is
not available for all models.)
Image shown may differ from your TV.
y
The Kensington security system connector is
located at the rear of the TV. For more information
of installation and using, refer to the manual
provided with the Kensington security system or
visit
http://www.kensington.com.
Connect the Kensington security system cable
between the TV and a table.
2 EA, P4 x 8
(Only 47/50LN57**-ZE/ZK, 47/50LA62**,47/50L
A64**,47/50LA66**)
2 EA, M4 x 8
(Only 32/39/42LN57**-ZE/ZK, 32/39/42LA62**,
32/42LA64**, 32/42LA66**)
Page 28
ASSEMBLING AND PREPARING
20
ENGLISH
ENG
NOTE
(Only 32/39/42/47/50LN57**-ZE/ZK,
32/39/42/47/50LA62**, 32/42/47/50LA64**,
32/42/47/50LA66**)
How to fix the TV to a table
1. Connect the Desk-mount Cables to the
Stand Base using the Bracket Screws.
2. Fix the Desk-mount Cables to a table using
the Desk-mount Screws.
3. Once the TV is fixed, move the table close to
the wall. Children may go in, causing injuries.
WARNING
yTo prevent TV from falling over, the TV
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause injury.
Adjusting the angle of the TV to suit view
(This feature is not available for all models.)
Swivel 15 degrees to the left or right and adjust the
angle of the TV to suit your view.
(Only LA62**, LA64**, LA66**, LN57**-ZE/ZK)
1515
Swivel 10 degrees to the left or right and adjust the
angle of the TV to suit your view.
(Only 42/47LA69**, 42/47LA74**)
1010
Swivel 8 degrees to the left or right and adjust the
angle of the TV to suit your view.
(Only 55LA69**, 55/60LA74**)
88
Page 29
ASSEMBLING AND PREPARING
21
CAUTION
yWhen adjusting the angle adof the product,
watch out for your fingers.
»
Personal injury may occur if hands or fingers
are pinched. If the product is tilted too much, it
may fall, causing damage or injury.
<Rear><Front>
Securing the TV to a wall
(This feature is not available for all models.)
CAUTION
yMake sure that children do not climb on or
hang on the TV.
NOTE
yUse a platform or cabinet that is strong and
large enough to support the TV securely.
yBrackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
ENGENGLISH
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
at surface.
10 cm
10 cm
10 cm
10 cm
Page 30
ASSEMBLING AND PREPARING
22
ENGLISH
ENG
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
Model 32LA62**
VESA (A x B)200 x 100200 x 200
Standard screwM4M6
Number of screws 44
Wall mount
or install the TV. Otherwise electric shock
may occur.
yIf you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorised LG wall mount and
contact the local dealer or qualified
personnel.
yDo not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yUse the screws and wall mounts that meet
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
NOTE
yUse the screws that are listed on the VESA
standard screw specifications.
yThe wall mount kit includes an installation
manual and necessary parts.
yThe wall mount bracket is not provided. You
can obtain additional accessories from your
local dealer.
yThe length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yFor more information, refer to the manual
supplied with the wall mount.
yWhen attaching a third-party wall mounting
bracket to the TV, insert the wall mount
inner spacers into the TV wall mount holes
to move your TV in vertical angle. Please
make sure not to use the spacers for LG
wall mounting bracket. (Only LA64**)
Wall Mount Inner Spacer
Page 31
REMOTE CONTROL
APP/*
MUTE
FAV
P
GUIDE
SMART
MY APPS
REC
LIVE TV
23
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yDo not mix old and new batteries, as this may damage the remote control.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LN570*, LN575*, LN577*)
TV/RAD Selects Radio, TV and DTV programme.
SUBTITLE Recalls your preferred subtitle in digital mode.
Q. MENU Accesses the quick menus.
GUIDE Shows programme guide.
RATIO Resizes an image.
INPUT Changes the input source.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
FAV Accesses your favourite programme list.
APP/* Select the MHP TV menu source. (Only Italy.) (Depending on model)
PAGE Moves to the previous or next screen.
1
TELETEXT BUTTONS These buttons are used for teletext.
Views the information of the current programme and screen.
INFO
SMART Accesses the Smart Home menus.
MY APPS Shows the list of Apps.
1
2
1
Navigation buttons (up/down/left/right) Scrolls through menus or options.
Selects menus or options and confirms your input.
OK
BACK Returns to the previous level.
EXIT Clears on-screen displays and return to TV viewing.
SETTINGS Accesses the main menus.
REC Start to record and display record menu.
LIVE TV Return to LIVE TV.
Control buttons (
) Controls the Premium contents, Time
Machine or Smart Share menus or the SIMPLINK compatible devices (USB
or SIMPLINK or Time Machine).
2
Colour buttons These access special functions in some menus.
(: Red, : Green, : Yellow, : Blue)
ENGENGLISH
or
Page 32
REMOTE CONTROL
P
A
G
E
TV/
RAD
RATIOINPUT
FAV
MUTE
EXIT
OK
GUIDE
MY APPS
LIVE TV
REC
TEXT
T.OPT
SUBTITLE
Q.MENU
AD
BACK
SETTINGS
INFO
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
9
wxyz
LIST
Q.VIEW
SMART
APP/*
24
ENGLISH
ENG
(Only LA62**, LA64**)
1
2
(User Guide) Sees user-guide.
RATIO Resizes an image.
INPUT Changes the input source.
TV/RAD Selects Radio, TV and DTV programme.
LIST Accesses the saved programme list.
(Space) Opens an empty space on the screen keyboard.
Q.VIEW Returns to the previously viewed programme.
FAV Accesses your favourite programme list.
3D Used for viewing 3D video.
PAGE Moves to the previous or next screen.
INFO Views the information of the current programme and screen.
SMART Accesses the Smart Home menus.
MY APPS Shows the list of Apps.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
Selects menus or options and confirms your input.
OK
BACK Returns to the previous level.
GUIDE Shows programme guide.
EXIT Clears on-screen displays and return to TV viewing.
1
Colour buttons These access special functions in some menus.
(: Red, : Green, : Yellow, : Blue)
2
TELETEXT BUTTONS These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Q. MENU Accesses the quick menus.
LIVE TV Return to LIVE TV.
Control buttons (
) Controls the Premium contents, Time
Machine or Smart Share menus or the SIMPLINK compatible devices (USB
or SIMPLINK or Time Machine).
REC
Start to record and display record menu.
SETTINGS Accesses the main menus.
AD Switches the Audio Description On or Off.
APP/* Select the MHP TV menu source. (Only Italy.) (Depending on model)
Page 33
MAGIC REMOTE CONTROL FUNCTIONS
25
MAGIC REMOTE CONTROL FUNCTIONS
This item is not included for all models.
When the message “Magic Remote Control battery is low. Change the battery.” is
displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching
and ends to the label inside the compartment, and close the battery cover. Be
sure to point the remote control toward the remote control sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yDo not mix old and new batteries, as this may damage the remote control.
(Only LA66**, LA69**, LA74**, LN578*)
(POWER)
Turns the TV on or off.
BACK
Returns to the previous level.
Wheel(OK)
Selects menus or options and
confirms your input.
Scrolls through the saved
programmes.
If you press the navigation
button while moving the pointer
on the screen, the pointer
disappears, and the Magic
Remote Control works as a
regular remote control.
To display the pointer again,
shake the Magic Remote
Control from side to side.
3D
Used for viewing 3D video.
(Depending on model)
BACKSMART
/Q.MENU
P
Pointer (RF transmitter)
Navigation buttons (up/down/
left/right)
Scrolls through menus or options.
SMART
Accesses the Smart Home
menus.
Voice recognition
(Depending on model)
/Q.MENU
Accesses the quick menus.
Accesses the Universal Control.
+ -
Adjusts the volume level.
ꕌPꕍ
Scrolls through the saved
programmes or channels.
MUTE
Mutes all sounds.
ENGENGLISH
Voice recognition(Depending on model)
Network connection is required to use the voice recognition function.
The recognition rate may vary depending on the user’s characteristics (voice, pronunciation, intonation
and speed) and the environment (noise and TV volume).
1. Press the Voice recognition button.
2. Speak when the voice display window appears on the left of the TV screen.
• The voice recognition may fail when you speak too fast or too slow.
• Use the Magic remote control no further than 10 cm from your face.
Page 34
MAGIC REMOTE CONTROL FUNCTIONS
HOME
26
ENGLISH
ENG
Registering Magic Remote
Control
It is necessary to ‘pair’ (register) the magic remote
control to your TV before it will work.
How to register the Magic Remote Control
1 To register automatically,
turn the TV on and press the
Wheel(OK) button. When
registration is completed, the
completion message appears
on the screen.
2 If registration fails, turn the TV
off and back on, then press
the Wheel(OK) button to
complete registration.
How to re-register the Magic Remote Control
BACK
SMART
1 Press and hold the BACK
and SMART
together for 5 seconds to
reset, then register it by
following “How to register the
Magic Remote Control” above.
2 To re-register the Magic
Remote Control, press and
hold the BACK
seconds toward the TV. When
registration is completed, the
completion message appears
on the screen.
buttons
button for 5
How to use Magic Remote
Control
1 If the pointer disappears, move
the Magic Remote Control
slightly to left or right. Then, it
will automatically appear on
the screen.
»
If the pointer has not been
used for a certain period of
time, it will disappear.
2 You can move the pointer by
aiming the Pointer Receiver of
the Magic Remote Control at
your TV then move it left, right,
up or down.
»
If the pointer does not work
properly, leave the Magic
Remote Control for 10
seconds then use it again.
11-1
More
If you press Wheel(OK) on the Magic
Remote Control, the following screen
appears.
1
Shows information about the current
programme and screen.
You can select More Menu.
2
Precautions to Take when
Using the Magic Remote
Control
Use the Magic Remote Control within the
y
maximum communication distance (10 m).
Using the Magic Remote Control beyond this
distance, or with an object obstructing it, may
cause a communication failure.
A communication failure may occur due to
y
nearby devices. Electrical devices such as
a microwave oven or wireless LAN product
may cause interference, as these use the
same bandwidth (2.4 GHz) as the Magic
Remote Control.
The Magic Remote Control may be damaged
y
or may malfunction if it is dropped or receives
a heavy impact.
Take care not to bump into nearby furniture
y
or other people when using the Magic
Remote Control.
Manufacturer and installer cannot provide
y
service related to human safety as the
applicable wireless device has possibility of
electric wave interference.
It is recommended that an Access Point (AP)
y
be located more than 1 m away from the
TV. If the AP is installed closer than 1 m, the
Magic Remote Control may not perform as
expected due to frequency interference.
Page 35
USING THE USER GUIDE
27
USING THE USER GUIDE
User Guide allows you to more easily access the detailed TV information.
1 Press the SMART
Smart Home menu.
2 Select User Guide and press Wheel(OK).
NOTE
yYou can also access the User Guide by
pressing
control.(Only LA62**, LA64**)
(User Guide) in the remote
button to access the
more
More
User Guide
User Guide
OPTION > To set language
SMART Settings OPTION Language
Selects Menu Language and Audio Language displayed on the screen.
Menu Language
Selects a language for the display text.
[In Digital Mode Only]
Audio Language
When watching a digital broadcast containing several audio
languages, you can select the language you want.
[In Digital mode Only]
Use the Subtitle function when two or more subtitle
Subtitle
languages are broadcast.
Language
✎ If subtitle data in a selected language is not broadcast,
the default language subtitle will be displayed.
Shows the description of the selected menu.
1
You can use ꕌ/ꕍto move between pages.
Moves to the selected menu directly from the
2
User Guide.
1
2
Try Now
Close
IndexOnline User Guide
ENGENGLISH
User Guide
1
PROGRAMME Setting
PICTURE, SOUND Setting
OPTION
LG SMART Function
Advanced Function
Information
Shows the current watching programme or
1
3
To use input device
To set time options
To set TV lock options
To set language
To set country
Disabled Assisstance
2
To set Magic remote control
Index
45
Online User Guide
input source screen.
Allows to select the category you want.
2
Allows to select the item you want.
3
You can use ꕌ/ꕍto move between pages.
Allows to browse the description of the
4
function you want from the index.
Provides the detailed information on the
5
functions of LG Smart TV when the Internet
is connected.
(It may not be available depending on the
country/language.)
Page 36
ENGLISH
ENGLISH
ENG
ENG
MAINTENANCE / TROUBLESHOOTING
28
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yMake sure to turn the power off and disconnect the power cord and all other cables first.
yWhen the TV is left unattended and unused for a long time, disconnect the power cord from the wall
outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yTo remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yTo remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yAvoid touching the screen at all times, as this may result in damage to the screen.
yDo not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
scratches and image distortions.
yDo not use any chemicals as this may damage the product.
yDo not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
ProblemSolution
Cannot control
the TV with the
remote control.
No image display
and no sound is
produced.
The TV turns off
suddenly.
When connecting
to the PC (HDMI
DVI), ‘No signal’
or ‘Invalid Format’
is displayed.
yCheck the remote control sensor on the product and try again.
yCheck if there is any obstacle between the product and the remote control.
yCheck if the batteries are still working and properly installed (
yCheck if the product is turned on.
yCheck if the power cord is connected to a wall outlet.
yCheck if there is a problem in the wall outlet by connecting other products.
yCheck the power control settings. The power supply may be interrupted.
yCheck if the Auto sleep feature is activated in the Time settings.
yIf there is no signal while the TV is on, the TV will turn off automatically after
15 minutes of inactivity.
yTurn the TV off/on using the remote control.
yReconnect the HDMI cable.
yRestart the PC with the TV on.
to , to ).
Page 37
EXTERNAL CONTROL DEVICE SETUP / SPECIFICATIONS
0197
29
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com
SPECIFICATIONS
(Only LA66**, LA69**, LA74**, LN578*)
Wireless LAN module (TWFM-B006D) specification
StandardIEEE802.11a/b/g/n
2400 to 2483.5 MHz
Frequency Range
Output Power
(Max.)
Bluetooth module (BM-LDS401) specification
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4GHz: 11 dBm
802.11n - 5GHz: 12.5 dBm
ENGENGLISH
StandardBluetooth Version 3.0
Frequency Range2400 ~ 2483.5 MHz
Output Power (Max.)10 dBm or lower
Because band channel used by the country could be different, the user can not change or adjust the
y
operating frequency and this product is set for the regional frequency table.
Page 38
SPECIFICATIONS
0197
30
ENGLISH
ENG
(Only LN575*, LN577*, LA62**, LA64**)
Wireless LAN module(TWFM-B006D) specification
StandardIEEE802.11a/b/g/n
2400 to 2483.5 MHz
Frequency Range
Output Power
(Max.)
Because band channel used by the country could be different, the user can not change or adjust the
y
operating frequency and this product is set for the regional frequency table.
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4GHz: 11 dBm
802.11n - 5GHz: 12.5 dBm
Page 39
MANUALE UTENTE
TV LED
* TV LED LG include uno schermo LCD con retroilluminazione LED.
Leggere attentamente il presente manuale prima di utilizzare
l'apparecchio e conservarlo come riferimento futuro.
www.lg.com
Page 40
ITALIANO
ITA
INDICE
2
INDICE
3 LICENZE
3 AVVISO PER IL SOFTWARE OPEN
SOURCE
4 ISTRUZIONI DI SICUREZZA
10 - Visione di immagini 3D (solo modelli 3D)
12 PROCEDURA DI INSTALLAZIONE
12 MONTAGGIO E PREPARAZIONE
12 Disimballaggio
16 Acquisto separato
17 Componenti e pulsanti
18 Sollevamento e spostamento del TV
19 Montaggio su un tavolo
21 Montaggio a parete
23 TELECOMANDO
25 FUNZIONI DEL TELCOMANDO
MAGIC REMOTE
26 Registrazione del telcomando Magic
Remote
26 Come utilizzare il telcomando Magic
Remote
26 Precauzioni nell'uso del telcomando Magic
Remote
27 UTILIZZO DELLA GUIDA UTENTE
28 MANUTENZIONE
28 Pulizia del televisore
28 - Schermo, cornice, telaio e supporto
28 - Cavo di alimentazione
28 RISOLUZIONE DEI PROBLEMI
29 IMPOSTAZIONE DI UN DISPOSITIVO
DI CONTROLLO ESTERNO
29 SPECIFICHE TECNICHE
39 DIAGRAMMI A BLOCCHI
AVVISO
yIgnorando i messaggi di avviso, si corre
il rischio di subire gravi lesioni fisiche o di
provocare incidenti o danni letali.
ATTENZIONE
yIgnorando i messaggi di attenzione, si corre
il rischio di subire lesioni fisiche minori o di
danneggiare il prodotto.
NOTA
yLe note forniscono chiarimenti e informazioni
su come utilizzare il prodotto in modo sicuro.
Leggere le note attentamente prima di
utilizzare il prodotto.
Page 41
LICENZE / AVVISO PER IL SOFTWARE OPEN SOURCE
LICENZE
Le licenze supportate possono variare da un modello all'altro. Per ulteriori informazioni sulle licenze,
visitare il sito www.lg.com.
Prodotto su licenza dei Dolby Laboratories. "Dolby" e il simbolo della doppia D sono
marchi dei Dolby Laboratories.
I termini HDMI e HDMI High-Definition Multimedia Interface e il logo HDMI sono
marchi commerciali o marchi commerciali registrati negli Stati Uniti e in altri paesi di
HDMI Licensing, LLC .
3
INFORMAZIONI SU DIVX VIDEO: DivX® è un formato video digitale creato da DivX,
LLC, società controllata da Rovi Corporation. Questo è un dispositivo DivX Certied®
ufciale che riproduce video DivX. Per ulteriori informazioni e strumenti software per
convertire i le in video DivX, visitare divx.com.
INFORMAZIONI SU DIVX VIDEO-ON-DEMAND: questo dispositivo DivX Certied®
deve essere registrato per poter riprodurre i lm acquistati in formato DivX Video-on-
Demand (VOD). Per ottenere il codice di registrazione, individuare la sezione DivX
VOD nel menu di congurazione del dispositivo. Visitare il sito vod.divx.com per
ulteriori informazioni su come completare la procedura di registrazione.
"DivX Certied® per riprodurre video DivX® in alta denizione no a 1080p, compresi
i contenuti premium."
"DivX®, DivX Certied® e i logo associati sono marchi di Rovi Corporation o società
da questa controllate e sono utilizzati in concessione di licenza".
"Coperto da uno o più dei seguenti brevetti degli Stati Uniti:"
7,295,673; 7,460,668; 7,515,710; 7,519,274”
Prodotto su licenza e coperto da uno o più dei seguenti numeri di brevetto degli Stati
Uniti: 5.956.674; 5.974.380; 6.487.535 e altri brevetti degli Stati Uniti e di altri Paesi
rilasciati o in attesa di approvazione. DTS, il simbolo, e DTS insieme al simbolo, sono
marchi registrati; DTS 2.0+Digital Out è un marchio registrato di DTS, Inc. Il prodotto
Per ottenere il codice sorgente contenuto in questo prodotto secondo quanto consentito dalle licenze GPL,
LGPL, MPL e altre licenze Open Source, visitare http://opensource.lge.com.
In aggiunta al codice sorgente, sono disponibili per il download tutti i termini di licenza, le esclusioni di
responsabilità e le relative note di copyright.
LG Electronics fornisce anche il codice Open Source su CD-ROM a fronte del pagamento di una cifra a
copertura dei costi che tale distribuzione comporta (come il costo del supporto, di spedizione e gestione)
in seguito a richiesta inviata via e-mail a: opensource@lge.com. Questa offerta è valida per tre (3) anni a
partire dalla data di acquisto del prodotto.
Page 42
ITALIANO
ITA
ISTRUZIONI DI SICUREZZA
4
ISTRUZIONI DI SICUREZZA
Leggere attentamente queste istruzioni di sicurezza prima di utilizzare il prodotto.
AVVISO
Non collocare il televisore e il telecomando nei seguenti ambienti:
y
- In un luogo esposto alla luce diretta del sole
- In un luogo dove è presente un elevato livello di umidità, ad esempio in bagno
- Vicino a fonti di calore, ad esempio stufe o altri dispositivi che producono calore
- Vicino a piani cottura o umidificatori, dove è facilmente esposto a vapore o
schizzi di olio
- In un'area esposta alla pioggia o al vento
- Vicino a contenitori d'acqua, ad esempio vasi
Ciò potrebbe comportare il rischio di incendi, scosse elettriche, malfunzionamento
o deformazione del prodotto.
Non posizionare il prodotto in un luogo soggetto alla polvere.
y
Ciò potrebbe costituire rischio di incendio.
La presa di rete rappresenta il dispositivo di scollegamento. La presa deve essere
y
facilmente raggiungibile.
Non toccare la presa con le mani bagnate. Inoltre, se il terminale del cavo è
y
bagnato o ricoperto di polvere, asciugarlo completamente o rimuovere la polvere.
L'eccesso di umidità può provocare scosse elettriche.
Accertarsi di collegare il cavo di alimentazione alla messa a terra. (Ad eccezione
y
dei dispositivi privi di messa a terra.)
Si potrebbero subire scosse elettriche o lesioni.
Inserire completamente il cavo di alimentazione.
y
Se il cavo di alimentazione non viene inserito completamente, si potrebbe
verificare un incendio.
Accertarsi che il cavo di alimentazione non venga a contatto con oggetti caldi, ad
y
esempio un radiatore.
Ciò potrebbe costituire rischio di incendio o di scosse elettriche.
Non posizionare oggetti pesanti, o il prodotto stesso, sui cavi di alimentazione.
y
Ciò potrebbe costituire rischio di scosse elettriche o incendio.
Piegare il cavo dell'antenna tra l'interno e l'esterno dell'edificio per impedire
y
l'ingresso di gocce di pioggia.
L'acqua può danneggiare il prodotto e provocare scosse elettriche.
Quando si monta il televisore sulla parete, assicurarsi di non far passare il cavo di
y
alimentazione e quello dell'antenna dietro al televisore.
Ciò potrebbe costituire rischio di incendio o di scosse elettriche.
Page 43
Desiccant
ISTRUZIONI DI SICUREZZA
Non collegare troppi dispositivi elettrici a una singola presa multipla.
y
Ciò potrebbe comportare il rischio di incendi dovuti a surriscaldamento.
Attenzione a non far cadere il prodotto quando si collegano dispositivi esterni.
y
Ciò potrebbe causare lesioni alle persone o danni al prodotto.
Tenere il materiale anti-umidità o vinilico dell'imballaggio fuori dalla portata dei
y
bambini.
Il materiale antiumidità è nocivo, se ingerito. Se accidentalmente ingerito, far
vomitare il paziente e portarlo al più vicino pronto soccorso. Inoltre il materiale
vinilico dell'imballaggio può provocare soffocamento. Tenerlo fuori dalla portata dei
bambini.
Impedire ai bambini di arrampicarsi o appendersi al televisore.
y
Il prodotto potrebbe cadere e provocare gravi lesioni.
Smaltire le batterie usate in modo appropriato per evitare che i bambini possano
y
ingerirle.
In caso di ingestione delle batterie, rivolgersi immediatamente a un medico.
5
ITAITALIANO
Non inserire un conduttore (ad esempio un bastoncino metallico) su una delle
y
estremità del cavo di alimentazione mentre l'altra estremità è inserita nella presa a
muro. Inoltre, non toccare il cavo di alimentazione subito dopo averlo inserito nella
presa a muro.
Si potrebbero subire scosse elettriche.
(in base al modello)
Non collocare o conservare sostanze infiammabili vicino al prodotto.
y
L'incauta manipolazione di sostanze infiammabili può causare esplosioni o incendi.
Non lasciare cadere nel prodotto oggetti metallici quali monete, mollette per capelli,
y
bastoncini o fil di ferro né oggetti infiammabili quali carta e fiammiferi. Prestare
particolare attenzione ai bambini.
Possono verificarsi scosse elettriche, incendi o lesioni fisiche alle persone. Se
un oggetto cade all'interno del prodotto, scollegare il cavo di alimentazione e
contattare il centro di assistenza.
Non spruzzare acqua sul prodotto né pulirlo con prodotti infiammabili (solventi o
y
benzene). Possono verificarsi incendi o scosse elettriche.
Evitare impatti d'urto sul prodotto o di far cadere oggetti all'interno del prodotto e
y
sullo schermo.
Vi è il rischio di lesioni alle persone o danneggiamenti al prodotto stesso.
Non toccare mai il prodotto o l'antenna durante un temporale.
y
Si potrebbero subire scosse elettriche.
In caso di perdita di gas, non toccare la presa a muro, aprire le finestre e ventilare.
y
Una scintilla potrebbe provocare un incendio o ustioni.
Page 44
ITALIANO
ITA
ISTRUZIONI DI SICUREZZA
6
Non disassemblare, riparare o modificare il prodotto a propria discrezione.
y
Vi è il rischio di provocare incendi o scosse elettriche.
Rivolgersi al centro di assistenza per effettuare il controllo, la taratura o le
riparazioni del caso.
Se si verifica una delle seguenti circostanze, scollegare immediatamente il
y
prodotto dall'alimentazione e contattare il centro di assistenza di zona.
- Il prodotto ha subito un urto
- Il prodotto è stato danneggiato
- Oggetti estranei sono caduti dentro il prodotto
- Il prodotto produce fumo o odori strani
Vi è il rischio di scosse elettriche o incendio.
Se si prevede di non utilizzare il prodotto per un lungo periodo, scollegare il cavo
y
di alimentazione dal prodotto.
I depositi di polvere possono provocare incendi, mentre l'usura dell'isolamento può
provocare perdite di elettricità, scosse elettriche o incendi.
L'apparecchio non deve essere esposto a gocce o spruzzi di acqua; oggetti
y
contenenti liquidi, quali vasi, non devono essere posizionati sull'apparecchio.
Page 45
ISTRUZIONI DI SICUREZZA
ATTENZIONE
Installare il prodotto in un luogo privo di onde radio.
y
Tra un'antenna esterna e le linee elettriche deve esserci una distanza sufficiente a
y
impedire che la prima tocchi le seconde anche in caso di caduta dell'antenna
per evitare il rischio di scosse elettriche.
Non installare il prodotto in luoghi quali mensole instabili o superfici inclinate.
y
Evitare inoltre luoghi soggetti a vibrazione o in cui il prodotto non sia sostenuto
appieno.
In caso contrario il prodotto potrebbe cadere o capovolgersi, con il rischio di lesioni
gravi o danneggiamento del prodotto stesso.
Se si installa il televisore su un supporto, usare delle precauzioni per evitare che
y
possa rovesciarsi. In caso contrario, il prodotto potrebbe cadere e provocare lesioni
alle persone.
Se si intende montare il prodotto su una parete, collegare l'interfaccia di montaggio VESA standard
y
(parti opzionali) al retro del prodotto. Quando si installa il set per utilizzare la staffa per montaggio a
parete (parti opzionali), fissarlo accuratamente in modo che non possa cadere.
Utilizzare solo gli accessori specificati dal produttore.
y
Per l'installazione dell'antenna, rivolgersi a personale qualificato.
y
Tale operazione può comportare il rischio di incendio o di scosse elettriche.
7
ITAITALIANO
Quando si guarda la televisione, si raccomanda di mantenere una distanza di
y
almeno 2 - 7 volte la lunghezza della diagonale dello schermo.
Guardando la TV per periodi prolungati si può avere un effetto di visione sfocata.
Utilizzare solo il tipo di batterie indicato.
y
In caso contrario, il telecomando potrebbe subire danneggiamenti.
Non utilizzare batterie vecchie e nuove contemporaneamente.
y
Ciò potrebbe causare il surriscaldamento e la perdita di liquido dalle stesse.
Non esporre le batterie a calore eccessivo, quindi tenerle lontano dalla luce diretta del sole, camini
y
aperti e stufe elettriche.
NON inserire batterie non ricaricabili nel dispositivo di ricarica.
y
Verificare che non vi siano oggetti tra il telecomando e il sensore.
y
La luce del sole e altre fonti luminose intense possono interferire con il segnale del
y
telecomando. Se ciò si verifica, oscurare la stanza.
Quando si collegano dispositivi esterni come console per videogiochi, verificare
y
che i cavi di collegamento siano sufficientemente lunghi.
In caso contrario il prodotto potrebbe cadere con il rischio di lesioni alle persone o
danneggiamento del prodotto stesso.
Page 46
ITALIANO
ITA
ISTRUZIONI DI SICUREZZA
8
Evitare di spegnere il prodotto scollegando il cavo dalla presa a muro. (Non usare
y
la spina come interruttore.)
Potrebbero verificarsi errori meccanici o scosse elettriche.
Seguire le istruzioni di installazione riportate di seguito per evitare il
y
surriscaldamento del prodotto.
- Collocare il prodotto a una distanza minima di 10 cm dalla parete.
- Non installare il prodotto in luoghi privi di ventilazione (ad esempio su una
mensola o all'interno di un mobile).
- Non installare il prodotto su un tappeto o su un cuscino.
- Controllare che la ventola dell'aria non sia bloccata da una tovaglia o da una
tenda.
In caso contrario, si rischia un incendio.
Dopo aver guardato a lungo il televisore, evitare di toccare le aperture per la
y
ventilazione poiché potrebbero essersi surriscaldate. Questo comportamento non
influisce sul funzionamento o sulle prestazioni del prodotto.
Esaminare periodicamente il cavo dell’apparecchio e se sono visibili danni o segni di usura,
y
scollegarlo, interrompere l'uso dell'apparecchio e sostituire il cavo con l'esatto componente di
ricambio presso un centro servizi autorizzato.
Evitare che la polvere si depositi sui terminali del cavo di alimentazione o sulla
y
presa.
Ciò potrebbe costituire rischio di incendio.
Proteggere il cavo di alimentazione da possibili danni fisici o meccanici, evitando
y
che venga intrecciato, annodato, schiacciato, incastrato in una porta o calpestato.
Prestare particolare attenzione alle prese, alle prese a muro e al punto in cui il
cavo esce dall'apparecchio.
Non premere con forza sul pannello con la mano od oggetti affilati, ad esempio
y
unghie, matite o penne e non graffiarlo.
Evitare di toccare lo schermo o di premere su di esso con le dita troppo a lungo.
y
Questa operazione potrebbe provocare alcuni effetti temporanei di distorsione sullo
schermo.
Quando si pulisce il prodotto e i suoi componenti, scollegare prima il cavo di
y
alimentazione e utilizzare un panno morbido. Non applicare eccessiva forza per
evitare di graffiare o scolorire lo schermo. Non spruzzare acqua né utilizzare panni
bagnati. Non utilizzare mai detergenti per vetri, lucidanti per automobili o industriali,
abrasivi o cere, benzene, alcol e prodotti simili che possono danneggiare il
prodotto e il suo pannello.
Ciò potrebbe comportare il rischio di incendio, scosse elettriche o danneggiamento
del prodotto (deformazione, corrosione o rottura).
Finché l’unità è collegata alla presa elettrica, non è scollegata dalla sorgente di alimentazione
y
nemmeno se viene spenta utilizzando l’interruttore.
Per scollegare il cavo, afferrare la spina e tirare.
y
Se si scollegano i fili all'interno del cavo di alimentazione, potrebbe svilupparsi un
incendio.
Quando si sposta il prodotto, accertarsi che sia stato spento. Quindi, scollegare i
y
cavi dell'alimentazione, dell'antenna e tutti i cavi di collegamento.
In caso contrario, vi è il rischio di danneggiare il televisore o il cavo di
alimentazione, con il rischio di incendio o scosse elettriche.
Page 47
ISTRUZIONI DI SICUREZZA
A causa del peso dell'apparecchio, si raccomanda di spostarlo o rimuoverlo dal
y
suo imballaggio in due persone.
In caso contrario, si possono subire lesioni.
Contattare il centro servizi una volta l'anno per pulire le parti interne del prodotto.
y
La polvere accumulata può causare danni meccanici.
Per l'assistenza, rivolgersi a personale qualificato. È necessario rivolgersi
y
all'assistenza se l'apparecchio è in qualsiasi modo danneggiato, ad esempio in
caso di danni al cavo o alla spina di alimentazione elettrica, liquidi o oggetti caduti
accidentalmente all'interno dell'apparecchio, esposizione a pioggia o umidità,
funzionamento non regolare o cadute.
Se il prodotto risulta freddo al tatto, si potrebbe verificare un leggero "tremolio"
y
all'accensione. Si tratta di un effetto normale, che non indica un malfunzionamento
del prodotto.
Il pannello è un prodotto ad alta tecnologia con risoluzione da due a sei milioni
y
di pixel. È possibile vedere sul pannello minuscoli puntini neri e/o altri puntini dai
colori vivaci (rosso, blu o verde) delle dimensioni di 1 ppm. Ciò non indica un
malfunzionamento e non incide sulle prestazioni e l'affidabilità del prodotto.
Questo fenomeno si verifica anche in prodotti di terze parti e non dà diritto alla
sostituzione del prodotto o a risarcimenti.
La luminosità e il colore del pannello possono differire a seconda della posizione di
y
visione (sinistra/destra/alto/basso).
Il fenomeno è dovuto alle caratteristiche del pannello. Non ha nulla a che vedere
con le prestazioni del prodotto e non indica malfunzionamento.
9
ITAITALIANO
Quando un'immagine fissa (ad esempio la trasmissione del logo di un canale, di un menu a schermo
y
o della scena di un videogioco) è visualizzata per un periodo di tempo prolungato, può danneggiare
lo schermo producendo un effetto noto come "persistenza delle immagini". La garanzia non copre il
prodotto per questo tipo di danno.
Evitare di visualizzare un'immagine fissa sullo schermo del televisore per un periodo prolungato (2 o
più ore per un LCD, 1 ora o più per un televisore al plasma).
Inoltre, se si guarda a lungo il TV utilizzando il formato 4:3, può prodursi un fenomeno di persistenza
delle immagini lungo i bordi del pannello.
Questo fenomeno si verifica anche in prodotti di terze parti e non dà diritto alla sostituzione del
prodotto o a risarcimenti.
Suoni e rumori prodotti dal televisore
y
"Crack": il crack che si avverte quando si guarda o si spegne il televisore è generato dalla
contrazione termica della plastica causata dalla temperatura e dall'umidità. Questo rumore è
comune nei prodotti che prevedono la deformazione dovuta ad agenti termici. Ronzio del pannello o
dei circuiti elettrici: il circuito di commutazione ad alta velocità produce un leggero rumore dovuto al
passaggio di una grande quantità di energia elettrica necessaria per il funzionamento del prodotto. Il
rumore varia a seconda del prodotto.
Il suono generato non incide sulle prestazioni e l'affidabilità del prodotto.
Page 48
ITALIANO
ITA
ISTRUZIONI DI SICUREZZA
10
Visione di immagini 3D (solo modelli 3D)
AVVISO
Ambiente di visione
yTempo di visione
- Quando si guardano contenuti 3D, fare una pausa di 5-15 minuti ogni ora. La visione prolungata di
contenuti 3D può causare mal di testa, vertigini, senso di stanchezza o affaticamento degli occhi.
Persone con crisi convulsive da fotosensibilizzazione o malattia cronica
yAlcuni utenti possono essere soggetti a crisi o altri sintomi anomali quando sono esposti a luci
lampeggianti o motivi particolari presenti nei contenuti 3D.
yEvitare di guardare video 3D se si avverte nausea, in gravidanza e/o se si soffre di una malattia cronica
come l'epilessia, un disturbo cardiaco o della pressione sanguigna, ecc.
yLa visione di contenuti 3D è sconsigliata se si soffre di cecità stereoscopica o anomalia stereoscopica.
In questi casi, le immagini possono apparire doppie e la visione può risultare fastidiosa.
ySe si soffre di strabismo, ambliopia (vista debole) o astigmatismo, è possibile che si abbia qualche
difcoltà a percepire la profondità e che ci si senta facilmente affaticati per le immagini doppie. È
consigliabile fare delle pause più frequenti rispetto a quelle normalmente prescritte a un adulto normale.
ySe la vista è diversa tra i due occhi, fare un esame degli occhi prima di guardare contenuti 3D.
Sintomi per i quali la visione di contenuti 3D è sconsigliata o richiede frequenti pause
yEvitare di guardare contenuti 3D se ci si sente stanchi per mancanza di sonno, lavoro eccessivo o per
aver bevuto alcolici.
ySe si avverte stanchezza, interrompere l'uso o la visione di contenuti 3D e riposarsi nché i sintomi
scompaiono.
- Se i sintomi persistono, consultare il medico. I sintomi includono mal di testa, dolore agli occhi,
nausea, palpitazioni, vista sfocata, fastidio, sdoppiamento delle immagini, problemi di visione o
affaticamento.
Page 49
ISTRUZIONI DI SICUREZZA
ATTENZIONE
Ambiente di visione
yDistanza di visione
- Quando si guardano contenuti 3D, mantenere una distanza pari almeno al doppio della lunghezza
diagonale dello schermo. Se la visione dei contenuti 3D non risulta confortevole, allontanarsi
ulteriormente dal televisore.
Età di visione
yBambini
- Per i bambini di età inferiore a 5 anni, l’uso o la visione di contenuti 3D è proibita.
- I bambini di età inferiore a 10 anni possono manifestare segni di iperattività e sovreccitazione
poiché le loro funzioni visive sono ancora in fase di sviluppo (ad esempio possono provare a
toccare lo schermo o a saltarvi dentro). Prestare particolare attenzione ai bambini quando guardano
contenuti 3D e non lasciarli soli.
- I bambini hanno una disparità binoculare (che crea le immagini 3D) maggiore rispetto agli adulti
poiché la distanza tra i loro occhi è minore di quella di un adulto. Pertanto essi percepiscono per la
stessa immagine 3D una profondità stereoscopica maggiore in confronto a un adulto.
yRagazzi
- I ragazzi di età inferiore a 19 anni possono reagire in modo sensibile a causa della stimolazione
luminosa dei contenuti 3D. Avvertirli di non guardare contenuti 3D a lungo quando sono stanchi.
yPersone anziane
- Le persone anziane possono percepire meno l’effetto 3D rispetto alle persone giovani. Non sedere
più vicino al televisore di quanto consigliato.
11
ITAITALIANO
Precauzioni nell'uso degli occhiali 3D
yUsare solo occhiali 3D LG. In caso contrario, potrebbe non essere possibile vedere i video 3D
correttamente.
yNon usare occhiali 3D in sostituzione di occhiali comuni, da sole o protettivi.
yL'uso di occhiali 3D modicati può causare affaticamento degli occhi o distorsione delle immagini.
yNon tenere gli occhiali 3D in ambienti con temperature molto basse o molto alte per evitare che possano
deformarsi.
yGli occhiali 3D sono fragili e si grafano facilmente. Utilizzare sempre un panno morbido e pulito per
detergere e lenti. Non utilizzare oggetti appuntiti sulle lenti degli occhiali 3D per evitare di grafarle e
non utilizzare sostanze chimiche per pulirle.
Page 50
PROCEDURA DI INSTALLAZIONE / MONTAGGIO E PREPARAZIONE
<
<
12
NOTA
yIl televisore raffigurato nell'immagine può essere diverso da quello in uso.
yIl menu OSD (On Screen Display) del TV potrebbe risultare leggermente diverso da quello mostrato
in questo manuale.
yI menu e le opzioni disponibili possono essere diversi a seconda della sorgente in ingresso o del
modello del prodotto utilizzati.
yIn futuro possono essere aggiunte nuove funzioni al televisore.
yIl televisore può essere posto in modalità standby per ridurre il consumo energetico. Spegnere
il televisore se si prevede di non guardarlo per un periodo prolungato. In tal modo si risparmierà
energia elettrica.
yÈ possibile ridurre notevolmente il consumo energetico riducendo il livello di luminosità dell'immagine.
In tal modo si riducono anche i costi complessivi di funzionamento.
ITALIANO
ITA
PROCEDURA DI INSTALLAZIONE
1 Aprire la confezione e vericare che tutti gli accessori siano inclusi.
2 Collegare il supporto al televisore.
3 Collegare un dispositivo esterno al televisore
4 Vericare che la connessione di rete sia disponibile.
È possibile utilizzare le funzioni di rete TV solo quando viene stabilita la connessione di rete.
MONTAGGIO E PREPARAZIONE
Disimballaggio
Vericare che nella confezione siano presenti i seguenti elementi. Se manca qualche accessorio, contattare
il rivenditore locale presso il quale è stato effettuato l'acquisto. Le illustrazioni presenti nel manuale
possono differire dal prodotto e dall'articolo effettivi.
ATTENZIONE
yPer garantire la sicurezza e la durata del prodotto, non utilizzare prodotti pirata.
yI danni o lesioni provocati da prodotti pirata non sono coperti dalla garanzia.
yAlcuni modelli presentano una sottile pellicola sullo schermo che non deve essere rimossa.
NOTA
yGli elementi forniti con il prodotto potrebbero variare in base al modello.
yLe specifiche del prodotto o il contenuto del presente manuale possono subire modifiche senza
preavviso in caso di aggiornamento delle funzioni del prodotto.
yPer un collegamento ottimale, le periferiche USB e i cavi HDMI devono essere dotati di cornici di
spessore inferiore a 10 mm e larghezza inferiore a 18 mm. Se il cavo USB o la memory stick USB
non sono compatibili con la porta USB del televisore, usare un cavo di estensione che supporta
(1 EA : Solo
32/39/42/47/50/60LN57**ZA)
(2 EA : Solo
32/39/42/47/50LN57**-ZE/
ZK, 32/39/42/47/50LA62**,
32/42/47/50LA64**,
32/42/47/50LA66**)
(Vedere pag. 19)
yGuida all’installazione dell’isolatore di antenna
- Utilizzare l’isolatore per installare la TV in un luogo in cui è presente una differenza di tensione tra il
set della TV e il GND di segnale dell’antenna.
» Se tale differenza di tensione è presente, il contatto dell’antenna potrebbe scaldarsi e l’eccessivo
calore potrebbe causare incidenti.
- È possibile migliorare la sicurezza mentre si guarda la TV rimuovendo efficacemente la tensione
di alimentazione dall’antenna. Si consiglia di montare l’isolatore alla parete. Se non è possibile
montarlo alla parete, montarlo sulla TV. Evitare di scollegare l’isolatore di antenna dopo
l’installazione, Prima di iniziare, assicurarsi di aver collegato l’antenna.
15
Parete
1. Collegamento alla TV.
ANTENNA/
CABLE IN
Cavo/Antenna
o
Isolatore
2. Collegamento al decoder.
Collegare un’estremità dell’isolatore al jack del cavo/antenna e l’altra al decoder o al set della TV.
“In alcuni casi è possibile che le apparecchiature collegate alla messa a terra protettiva dell’edicio
(attraverso il collegamento alle prese o ad altri dispositivi connessi alla messa a terra) e a un sistema di
distribuzione via cavo tramite un cavo coassiale possano incendiarsi. Quindi, è necessario effettuare il
collegamento a un sistema di distribuzione via cavo tramite un dispositivo in grado di fornire isolamento
elettrico al di sotto di una determinata gamma di frequenza (isolatore galvanico, vedere la norma EN
60728-11)”
Quando si applica l’isolatore RF è possibile che si verifichi una leggera perdita di sensibilità del segnale.
ITAITALIANO
Page 54
MONTAGGIO E PREPARAZIONE
P
123
16
Acquisto separato
(in base al modello)
Gli elementi acquistati separatamente possono subire cambiamenti o modiche senza preavviso ai ni del
miglioramento della qualità.
Per acquistare questi articoli, contattare il proprio rivenditore.
I dispositivi funzionano solo con alcuni modelli.
ITALIANO
ITA
AG-F***DP
Occhiali Dual play
AN-WF100
Chiavetta Wi-Fi collegata
Tag On
Tag on
Compatibilità
AG-F***DP
Occhiali Dual play
AG-F***
Occhiali 3D Cinema
AN-MR400
Telcomando Magic Remote
AN-WF100
Chiavetta Wi-Fi collegata
AN-VC4**
Telecamera per videochiamate
Dispositivo audio LG
Tag On
AG-F***
Occhiali 3D Cinema
AN-VC4**
Telecamera per videochiamate
LN57**
••
•
(in base al modello)
••
•
(in base al modello)
•
(in base al modello)
AN-MR400
Telcomando Magic Remote
Dispositivo audio LG
LA62**, LA64**,
LA66**, LA69**, LA74**
•
(in base al modello)
•
•
•
Il nome del modello o il design può cambiare in base all’aggiornamento delle funzioni del prodotto,
al produttore e alle politiche.
Page 55
Componenti e pulsanti
H
H
H
SETTINGS
INPUT
OK
SETTINGS
INPUT
OK
SETTINGS
INPUT
OK
MONTAGGIO E PREPARAZIONE
17
Tipo A : LA62**, LA64**, LA66**,
LN57**-ZE/ZK
Schermo
Altoparlanti
Sensore telecomando
LG Logo Light (Solo LA64**, LA66**)
Indicatore di alimentazione (Solo LA62**, LN57**-ZE/ZK)
Schermo
Pulsanti
OK
SETTINGS
INPUT
Pulsanti
Tipo B : LA69**, 42/47/55LA74**
Schermo
Altoparlanti
Sensore telecomando
LG Logo Light
Tipo D : LN57**-ZATipo C : 60LA74**
Schermo
Pulsanti
ITAITALIANO
Pulsanti
Altoparlanti
Sensore telecomando
LG Logo Light
Altoparlanti
Sensore telecomando
Indicatore di alimentazione
PulsanteDescrizione
Consente di scorrere tra i programmi salvati.
Consente di regolare il livello del volume.
Consente di selezionare l'opzione di menu evidenziata o confermare
un'opzione.
SConsente di accedere al menu principale o di salvare le scelte effettuate e
uscire dal menu.
Consente di modificare la sorgente in ingresso.
Consente di accendere o spegnere il dispositivo.
NOTA
yÈ possibile impostare la luce del logo LG su Accesso o Spento selezionando OPZIONE nei menu principali.(in
base al modello)
Page 56
MONTAGGIO E PREPARAZIONE
18
ITALIANO
ITA
Sollevamento e
spostamento del TV
Prima di sollevare o spostare il televisore, leggere
le seguenti indicazioni per evitare di grafare o
danneggiare l'apparecchio e per un trasporto
sicuro a prescindere dal tipo e dalle dimensioni.
ATTENZIONE
yEvitare di toccare continuamente lo schermo
per non rischiare di danneggiarlo.
ySi consiglia di spostare il televisore nella
scatola o con il materiale di imballaggio
originale.
yPrima di sollevare o spostare il televisore,
scollegare il cavo di alimentazione e tutti i cavi.
yQuando si afferra il televisore, lo schermo deve
essere rivolto dall'altro lato per evitare danni.
yPer trasportare un televisore di grandi
dimensioni occorrono 2 o 3 persone.
yDurante il trasporto, tenere il televisore come
mostrato nell'illustrazione di seguito.
yDurante il trasporto, non esporre il televisore a
oscillazioni o eccessive vibrazioni.
yDurante il trasporto, tenere il televisore diritto,
non ruotarlo su un lato o inclinarlo in avanti o
verso destra o sinistra.
yEvitare di esercitare una pressione eccessiva
poiché si potrebbe piegare/incurvare il telaio e,
di conseguenza, danneggiare lo schermo.
yAfferrare saldamente la parte superiore ed
inferiore della cornice del televisore. Fare
attenzione a non afferrare la parte trasparente,
l'altoparlante o la griglia dell'altoparlante.
Page 57
MONTAGGIO E PREPARAZIONE
19
Montaggio su un tavolo
1 Sollevare ed inclinare il televisore in posizione
verticale su un tavolo.
- Lasciare uno spazio (minimo) di 10
cm dalla parete per assicurare una
ventilazione adeguata.
10 cm
10 cm
10 cm
2 Collegare il cavo di alimentazione alla presa a
muro.
ATTENZIONE
yNon posizionare il televisore vicino a fonti di
calore, in quanto ciò potrebbe causare un
incendio o danni.
10 cm
10 cm
Fissaggio della TV al tavolo
Fissare il televisore al tavolo per evitare cadute,
danni ed eventuali lesioni.
Per ssare la TV al tavolo, inserire e ssare le viti
in dotazione sul retro del supporto.
(Solo 32/39/42/47/50/60LN57**-ZA)
Utilizzo del sistema di sicurezza Kensington
(funzione non disponibile su tutti i modelli).
L'immagine mostrata qui può essere diversa
y
dal televisore in uso.
Il connettore del sistema di sicurezza Kensington
è situato sul retro del televisore. Per ulteriori
informazioni sull'installazione e l'utilizzo, consultare
il manuale fornito in dotazione con il sistema di
sicurezza Kensington o visitare il sito
kensington.com.
Collegare il cav o de l si s t ema di sicur e z z a
Kensington tra il televisore ed un tavolo.
http://www.
2 EA, P4 x 8
(Solo 47/50LN57**-ZE/ZK, 47/50LA62**,
47/50LA64**,47/50LA66**)
2 EA, M4 x 8
(Solo 32/39/42LN57**-ZE/ZK, 32/39/42LA62**,
32/42LA64**, 32/42LA66**)
Page 58
MONTAGGIO E PREPARAZIONE
20
ITALIANO
ITA
NOTA
(Solo 32/39/42/47/50LN57**-ZE/ZK,
32/39/42/47/50LA62**, 32/42/47/50LA64**,
32/42/47/50LA66**)
Come fissare la TV su un tavolo
1. Collegare i cavi per il montaggio sul tavolo
alla base del supporto utilizzando le viti della
staffa.
2. Fissare i cavi per il montaggio sul tavolo
utilizzando le viti per il montaggio sul tavolo.
3. Una volta fissata la TV, avvicinare il tavolo
alla parete. I bambini potrebbero entrare e
provocarsi lesioni.
AVVISO
yPer evitare che il televisore si ribalti, fissarlo
saldamente al piano o alla parete, come
indicato nelle istruzioni di installazione.
Inclinare, scuotere o far oscillare il televisore
può provocare lesioni.
Regolazione dell'angolazione del televisore
per una migliore visione
(Funzione non disponibile su tutti i modelli.)
Regolare l'angolazione del televisore per adattarla
alla visione ruotando di 15 gradi a sinistra o destra
e regolare l'angolazione per adattarla alla visione.
(Solo LA62**, LA64**, LA66**, LN57**-ZE/ZK)
1515
Ruotare di 10 gradi a sinistra o a destra e regolare
l'angolo del televisore per adattarlo alla visione.
(Solo 42/47LA69**, 42/47LA74**)
1010
Ruotare di 8 gradi a sinistra o a destra e regolare
l’angolo del televisore per adattarlo alla visione.
(Solo 55LA69**, 55/60LA74**)
88
Page 59
MONTAGGIO E PREPARAZIONE
21
ATTENZIONE
yFare attenzione alle dita quando si regola
l'angolazione della TV.
»
Se le mani o le dita restano incastrate, ci si
può ferire. Se si inclina eccessivamente il
prodotto, potrebbe cadere causando lesioni o
danni.
<Retro><Fronte>
Fissaggio della TV alla parete
(Funzione non disponibile su tutti i modelli.)
ATTENZIONE
yImpedire ai bambini di arrampicarsi o
aggrapparsi al televisore.
NOTA
yUtilizzare un piano o un mobile
sufficientemente grandi e robusti da
sostenere correttamente il televisore.
yStaffe, bulloni e corde non sono forniti. È
possibile acquistare gli accessori opzionali
presso il rivenditore locale di fiducia.
ITAITALIANO
Montaggio a parete
Montare attentamente la staffa per il montaggio a
parete opzionale sul retro del televisore e ssare
la staffa su una parete solida perpendicolare al
pavimento. Per ssare il televisore su altri materiali
da costruzione, contattare il personale qualicato.
LG consiglia di far eseguire il montaggio a parete
da un installatore qualicato esperto.
1 Inserire e ssare i bulloni a occhiello o le staffe
del televisore e i bulloni sul retro del televisore.
- Se vi sono bulloni inseriti nella posizione
dei bulloni a occhiello, rimuoverli.
2 Montare le staffe con le viti sulla parete.
Far corrispondere la posizione della staffa e dei
bulloni a occhiello sul retro del televisore.
3 Legare strettamente i bulloni a occhiello alle
staffe con una corda robusta.
Assicurarsi di mantenere la corda orizzontale
con la supercie piatta.
10 cm
10 cm
10 cm
10 cm
Page 60
ITALIANO
ITA
MONTAGGIO E PREPARAZIONE
22
Accertarsi di utilizzare viti e staffe per il montaggio
a parete conformi agli standard VESA. Le
dimensioni standard per i kit di montaggio a parete
sono descritti nella seguente tabella.
Acquisto separato (Staffa per montaggio a parete)
Modello
VESA (A x B)
Vite standard
Numero di viti
Staffa per
montaggio a
parete
o installare il televisore. In caso contrario, si
rischiano scosse elettriche.
ySe si installa il TV al soffitto o su una a
parete inclinata, potrebbe cadere e causare
gravi lesioni.
Utilizzare un supporto per montaggio a
parete autorizzato da LG e contattare il
rivenditore locale o il personale qualificato.
yNon serrare eccessivamente le viti per
evitare danni al televisore e rendere nulla la
garanzia.
yUtilizzare le viti e i supporti a parete
conformi agli standard VESA. Gli eventuali
danni o lesioni causati dall'uso errato o
dall'utilizzo di un accessorio non compatibile
non sono coperti dalla garanzia.
NOTA
yUtilizzare le viti elencate nelle specifiche delle
viti conformi agli standard VESA.
yIl kit per il montaggio a parete include un
manuale di installazione e i componenti
necessari.
yLa staffa per montaggio a parete è un
accessorio opzionale. È possibile acquistare
gli accessori opzionali presso il rivenditore
locale di fiducia.
yLa lunghezza delle viti può variare in base
alla staffa di montaggio a parete. Accertarsi di
utilizzare la lunghezza appropriata.
yPer ulteriori informazioni, consultare il manuale
fornito con la staffa di montaggio a parete.
ySe si monta una staffa per montaggio a parete
di terze parti, inserire i distanziali interni per
il montaggio a parete nei fori per montaggio
a parete sul retro del televisore per spostare
il televisore in un'angolazione verticale.
Accertarsi di non utilizzare i distanziali per
le staffe di montaggio a parete LG. (Solo
LA64**)
Distanziali interni per il montaggio a parete
Page 61
TELECOMANDO
APP/*
MUTE
FAV
P
GUIDE
SMART
MY APPS
REC
LIVE TV
TELECOMANDO
Le descrizioni nel presente manuale si basano sui pulsanti del telecomando.
Leggere attentamente il presente manuale e utilizzare correttamente il televisore.
Per sostituire le batterie, aprire il coperchio del vano batterie, inserire le batterie (AAA
da 1,5 V) rispettando le polarità e come indicato dall'etichetta all'interno del vano
e chiudere il coperchio.
Per rimuovere le batterie, eseguire la procedura di installazione all'inverso.
ATTENZIONE
yNon utilizzare batterie vecchie e nuove contemporaneamente; ciò potrebbe causare danni al
telecomando.
Accertarsi di puntare il telecomando verso il sensore sul televisore.
23
o
(Solo LN570*, LN575*, LN577*)
1
1
2
TV/RAD Consente di selezionare il programma Radio, TV o DTV.
SUBTITLE Consente di visualizzare i sottotitoli preferiti in modalità digitale.
Q. MENU Consente di accedere ai menu rapidi.
GUIDE Mostra la Guida al programma.
RATIO Consente di ridimensionare un'immagine.
INPUT Consente di modificare la sorgente in ingresso.
LIST Consente di accedere all’elenco programmi salvato.
Q.VIEW Consente di tornare al programma precedente.
FAV Consente di accedere all’elenco di canali preferiti.
APP/* Consente di selezionare la sorgente di menu MHP TV. (Solo Italia) (In
base al modello)
PAGE Consente di spostarsi alla schermata precedente o successiva.
1
TASTI TELETEXT Questi pulsanti vengono utilizzati per il teletext.
INFO Consente di visualizzare le informazioni del programma e della
schermata correnti.
SMART Consente di accedere ai menu della schermata principale Smart.
MY APPS Visualizza l’elenco delle applicazioni.
Pulsanti di navigazione (su/giù/sinistra/destra) Consentono di scorrere i
menu e le opzioni.
OK Consente di selezionare menu e opzioni e confermare le scelte
effettuate.
BACK Consente di tornare al livello precedente.
EXIT Consente di eliminare dalla visualizzazione le schermate e di ripristinare
la modalità TV.
SETTINGS Consente di accedere ai menu principali.
REC
Consente di avviare la registrazione e visualizza il menu di
registrazione.
LIVE TV Consente di tornare a LIVE TV.
Pulsanti di controllo (
) Consentono di controllare i contenuti
Premium, i menu Time Machine o Smart Share o i dispositivi SIMPLINK
compatibili (USB o SIMPLINK o Time Machine).
2
Pulsanti colorati Consentono di accedere a funzioni speciali in alcuni
menu. (
: Rosso, : Verde, : Giallo, : Blu)
ITAITALIANO
Page 62
P
A
G
E
TV/
RAD
RATIOINPUT
FAV
MUTE
EXIT
OK
GUIDE
MY APPS
LIVE TV
REC
TEXT
T.OPT
SUBTITLE
Q.MENU
AD
BACK
SETTINGS
INFO
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
9
wxyz
LIST
Q.VIEW
SMART
APP/*
ITALIANO
ITA
TELECOMANDO
24
(Solo LA62**, LA64**)
1
2
(Guida utente) Visualizza la guida utente.
RATIO Consente di ridimensionare un'immagine.
INPUT Consente di modificare la sorgente in ingresso.
TV/RAD Consente di selezionare il programma Radio, TV o DTV.
LIST Consente di accedere all'elenco programmi salvato.
(Spazio) Inserisce uno spazio vuoto sulla tastiera a schermo.
Q.VIEW Consente di tornare al programma precedente.
FAV Consente di accedere all'elenco di canali preferiti.
3D Consente di vedere video 3D.
PAGE Consente di spostarsi alla schermata precedente o successiva.
INFO Consente di visualizzare le informazioni del programma e della
schermata correnti.
SMART Consente di accedere ai menu della schermata principale Smart.
MY APPS Visualizza l'elenco delle applicazioni.
Pulsanti di navigazione (su/giù/sinistra/destra) Consentono di scorrere i
menu e le opzioni.
OK
Consente di selezionare menu e opzioni e confermare le scelte
effettuate.
BACK Consente di tornare al livello precedente.
GUIDE Mostra la Guida al programma.
EXIT Consente di eliminare dalla visualizzazione le schermate e di ripristinare
la modalità TV.
1
Pulsanti colorati Consentono di accedere a funzioni speciali in alcuni
menu. (
2
TASTI TELETEXT Questi pulsanti vengono utilizzati per il teletext.
: Rosso, : Verde, : Giallo, : Blu)
SUBTITLE Consente di visualizzare i sottotitoli preferiti in modalità digitale.
Q. MENU Consente di accedere ai menu rapidi.
LIVE TV Consente di tornare a LIVE TV.
Pulsanti di controllo (
) Consentono di controllare i contenuti
Premium, i menu DVR o Smart Share o i dispositivi SIMPLINK compatibili (USB
o SIMPLINK o Time Machine).
REC
Consente di avviare la registrazione e visualizza il menu di
registrazione.
SETTINGS Consente di accedere ai menu principali.
AD (Descrizione audio) Consente di attivare e disattivare la descrizione
audio.
APP/* Consente di selezionare la sorgente di menu MHP TV. (Solo Italia) (In
base al modello)
Page 63
FUNZIONI DEL TELCOMANDO MAGIC REMOTE
P
BACKSMART
/Q.MENU
Articolo non incluso in tutti i modelli.
Quando viene visualizzato il messaggio "Batteria telcomando Magic Remote quasi
scarica. Sostituire batteria.", sostituire la batteria.
Per sostituire le batterie, aprire il coperchio del vano batterie, sostituire le batterie (AA
da 1,5 V) facendo corrispondere le estremità e ai simboli presenti all'interno del
vano e chiudere il coperchio. Accertarsi di indirizzare il telecomando verso il relativo
sensore sul televisore.
Per rimuovere le batterie, eseguire le operazioni di installazione in senso inverso.
yNon utilizzare batterie vecchie e nuove contemporaneamente; ciò potrebbe causare danni al
telecomando.
(Solo LA66**, LA69**, LA74**, LN578*)
Consente di tornare al livello
Consente di selezionare menu
Consente di scorrere i canali
navigazione mentre si muove
telcomando Magic Remote.
Viene utilizzato per la visione
di video 3D.
ATTENZIONE
(ACCENSIONE)
Consente di accendere o
e opzioni e confermare le
Se si preme il pulsante di
il puntatore sullo schermo,
il puntatore scompare e il
telcomando Magic Remote
funziona come un normale
Per visualizzare di nuovo
spegnere la TV.
BACK
precedente.
Rotella (OK)
scelte effettuate.
salvati.
telecomando.
il puntatore, scuotere il
3D
(in base al modello)
FUNZIONI DEL TELCOMANDO MAGIC REMOTE
Puntatore (trasmettitore RF)
Pulsanti di navigazione (su/
giù/sinistra/destra)
Consentono di scorrere i menu
e le opzioni.
SMART
Consente di accedere ai
menu della schermata principale Smart.
Riconoscimento vocale
(in base al modello)
/Q.MENU
Consente di accedere ai menu
rapidi.
Consente di accedere al
Telecomando universale.
+ -
Consente di regolare il livello del
volume.
ꕌPꕍ
Consente di scorrere i programmi salvati o i canali.
MUTE
Consente di disattivare tutti i
suoni.
25
ITAITALIANO
Riconoscimento vocale
Per utilizzare la funzione di riconoscimento vocale è necessaria una connessione di rete.
La velocità di riconoscimento può variare in base alle caratteristiche dell’utente (voce, pronuncia,
intonazione e velocità) e all’ambiente (rumore e volume del TV).
1. Premere il pulsante per il riconoscimento vocale.
2. Pronunciare il contenuto che si desidera quando viene visualizzata la finestra relativa alla voce
nella parte sinistra dello schermo del TV.
• Il riconoscimento vocale potrebbe non riuscire se si parla troppo rapidamente o troppo lentamente.
• Utilizzare il Telecomando magico a una distanza non superiore a 10 cm dal volto.
(in base al modello)
Page 64
ITALIANO
HOME
ITA
FUNZIONI DEL TELCOMANDO MAGIC REMOTE
26
Registrazione del
telcomando Magic Remote
È necessario “associare” (registrare) il telcomando
Magic Remote alla TV prima di utilizzarlo.
Come registrare il telcomando Magic Remote
1 Per registrare il telecomando
automaticamente, accendere
la TV e premere il tasto Rotella (OK). Quando la registrazione
è completata, viene visualizzato
il messaggio che indica il
completamento dell’operazione
sullo schermo.
2 Se la registrazione non
viene eseguita, spegnere
e riaccendere la TV, quindi
premere il tasto Rotella (OK)
per completare la registrazione.
Come ri-registrare il telcomando Magic Remote
1 Tenere premuti
BACK
(INDIETRO)
SMART
contemporaneamente i tasti
BACK
secondi per eseguire il reset,
quindi registrare il telecomando
seguendo la procedura
“Istruzioni di registrazione del
telcomando Magic Remote”
riportata in precedenza.
2 Per registrare nuovamente il
telcomando Magic Remote,
tenere premuto il tasto BACK
per 5 secondi puntando il
telecomando verso la TV.
Quando la registrazione è
completata, viene visualizzato
il messaggio che indica il
completamento dell’operazione
sullo schermo.
e SMART per 5
Come utilizzare il
telcomando Magic Remote
1 Se il puntatore scompare,
muovere leggermente il
telecomando verso destra o
sinistra. Il puntatore riapparirà
automaticamente sullo schermo.
»
Se non viene utilizzato per un
determinato periodo di tempo,
il puntatore viene nascosto.
2 Per spostare il puntatore, mirare
col puntatore ricevitore del
telecomando verso il televisore,
quindi spostarlo verso sinistra,
destra, verso l'alto o verso il
basso.
»
Se il puntatore non funziona
correttamente, lasciare il
telecomando per 10 secondi,
quindi riprovare.
11-1
Altro
Se si preme Rotella (OK) sul telcomando
Magic Remote, viene visualizzata la
seguente schermata.
1
La schermata contiene informazioni sul
programma in uso e sullo schermo.
È possibile selezionare il menu Altro.
2
Precauzioni nell'uso del
telcomando Magic Remote
Utilizzare il telecomando entro la distanza
y
massima di comunicazione (10 m). L'utilizzo
del telecomando oltre questa distanza o con
l'ostruzione di un oggetto potrebbe provocare
un errore di comunicazione.
Anche la presenza di dispositivi nelle
y
vicinanze potrebbe provocare un errore di
comunicazione. I dispositivi elettrici, quali
forni a microonde o prodotti LAN wireless,
potrebbero provocare interferenze poiché
utilizzano la stessa banda di frequenza (2,4
GHz) del telcomando Magic Remote.
Eventuali cadute o urti possono provocare
y
danni o malfunzionamenti del telecomando.
Quando si utilizza il telcomando Magic
y
Remote, prestare attenzione a non urtare
mobili o altre persone nelle vicinanze.
Il produttore e l'installatore non sono in
y
grado di fornire servizi relativi alla sicurezza
delle persone poiché il dispositivo wireless
potrebbe subire interferenze da onde
elettromagnetiche.
Si consiglia di collocare un eventuale
y
Access Point (punto di accesso) a più di 1
m di distanza dal televisore. Se l'Access
Point è installato a una distanza inferiore a
1 m, il telcomando Magic Remote potrebbe
non funzionare come previsto a causa di
interferenze sulla frequenza.
Page 65
UTILIZZO DELLA GUIDA UTENTE
UTILIZZO DELLA GUIDA UTENTE
La guida utente consente di accedere più facilmente a informazioni dettagliate sul televisore.
27
1 Premere il pulsante SMART
per accedere
alla schermata principale Smart.
2 Selezionare Manuale utente e premere
Wheel(OK).
altro
altro
Manuale utente
Manuale utente
NOTA
yÈ possibile accedere alla guida utente anche
premendo il tasto
telecomando.(Solo LA62**, LA64**)
Manuale utente
1
Impostazione CONFIG.
Impostazione IMMAGINE, SUONO
OPZIONE
Funzione LG SMART
Funzione avanzata
Informazione
Mostra il programma che si sta guardando
1
2
al momento o la schermata della sorgente di
ingresso.
Consente di selezionare la categoria
2
desiderata.
Consente di selezionare la voce desiderata.
3
È possibile utilizzare ꕌ/ꕍper spostarsi tra le
pagine.
Consente di scegliere la descrizione della
4
funzione desiderata dall'indice.
Fornisce informazioni dettagliate sulle
5
funzioni di LG Smart TV quando è attiva una
connessione Internet
(è possibile che questa funzione non sia
disponibile in tutti i Paesi o in tutte le lingue)
(Manuale utente) sul
3
Per utilizzare il dispositivo di ingresso
Per impostare le opzioni di ora
Per impostare le opzioni di blocco TV
Per impostare la lingua
Per impostare il paese
Assistenza disattivata
Per congurare il telecomando magico
Indice
Manuale dell’utente online
45
OPZIONE > Per impostare la lingua
SMART Impostazioni OPZIONE Lingua
Consente di selezionare la Lingua menu (Language) e la Lingua audio visualizzata sullo schermo.
Lingua menu (Language)
Consente di selezionare una lingua per il testo visualizzato.
[Solo in modalità digitale]
Durante la visualizzazione di una trasmissione digitale con diverse lingue
Lingua audio
audio, è possibile selezionare la lingua desiderata.
[Solo in modalità digitale]
Utilizzare la funzione dei sottotitoli quando sono trasmesse due o più
Lingua sottotitoli
lingue dei sottotitoli.
✎ Se i dati dei sottotitoli nella lingua selezionata non vengono trasmessi,
vengono riprodotti i sottotitoli nella lingua predenita.
Visualizza la descrizione del menu
1
1
Indice
selezionato.
È possibile utilizzare i tasti ꕌ/ꕍper spostarsi
tra le pagine.
Consente di spostarsi al menu selezionato
2
direttamente dalla guida utente.
Avvia
Chiudi
Manuale dell’utente online
2
ITAITALIANO
Page 66
MANUTENZIONE / RISOLUZIONE DEI PROBLEMI
28
MANUTENZIONE
Pulizia del televisore
Pulire regolarmente il televisore per mantenerne le prestazioni ottimali e per estenderne la durata nel
tempo.
ATTENZIONE
yInnanzitutto, accertarsi di spegnere e discollegare il cavo di alimentazione e tutti gli altri cavi.
yQuando il televisore viene lasciato incustodito e non in uso per un lungo periodo, scollegare il cavo di
alimentazione dalla presa a muro per evitare possibili danni derivanti da fulmini e sovratensioni elettriche.
ITALIANO
ITALIANO
ITA
ITA
Schermo, cornice, telaio e supporto
yPer rimuovere la polvere o lo sporco leggero, pulire la supercie con un panno morbido, asciutto e
pulito.
yPer rimuovere lo sporco maggiore, pulire la supercie con un panno morbido inumidito con acqua pulita
o un detergente delicato diluito. Quindi, passare immediatamente un panno asciutto.
ATTENZIONE
yEvitare di toccare continuamente lo schermo per non danneggiarlo.
yNon premere, strofinare o colpire la superficie dello schermo con le unghie o con oggetti affilati per
non graffiarlo e provocare distorsioni delle immagini.
yNon utilizzare agenti chimici perché potrebbero danneggiare il prodotto.
yNon nebulizzare del liquido sulla superficie. In caso di penetrazione di acqua nel televisore,
potrebbero verificarsi incendi, scosse elettriche o malfunzionamenti.
Cavo di alimentazione
Rimuovere regolarmente la polvere o lo sporco che si accumula sul cavo di alimentazione.
RISOLUZIONE DEI PROBLEMI
ProblemaSoluzione
Impossibile
controllare la TV con il
telecomando.
Non viene visualizzata
alcuna immagine e non
è prodotto alcun suono.
La TV si spegne
improvvisamente.
Durante il collegamento
al PC (HDMI DVI),
viene visualizzato il
messaggio “Nessun
segnale” o “Formato
non valido”.
yControllare il sensore del telecomando sul prodotto e riprovare.
yVerificare la presenza di eventuali ostacoli tra il televisore e il telecomando.
yControllare che le batterie siano ancora cariche e correttamente inserite ( su , su ).
yControllare che la TV sia accesa.
yVerificare che il cavo di alimentazione sia collegato ad una presa a muro.
yVerificare se esiste un problema nella presa a muro collegando altri prodotti.
yControllare le impostazioni di controllo dell'alimentazione. L'alimentazione potrebbe essere stata
interrotta.
yVerificare se la funzione Timer Spegnimento è attiva nelle impostazioni relative all'ora.
yIn mancanza del segnale, il televisore si spegne automaticamente dopo 15 minuti di inattività.
ySpegnere/accendere la TV utilizzando il telecomando.
yRicollegare il cavo HDMI.
yRiavviare il PC con la TV accesa.
Page 67
IMPOSTAZIONE DI UN DISPOSITIVO DI CONTROLLO ESTERNO / SPECIFICHE TECNICHE
0197
IMPOSTAZIONE DI UN DISPOSITIVO DI
CONTROLLO ESTERNO
Per informazioni sulla configurazione di un dispositivo di controllo esterno, visitare il sito Web www.lg.com
SPECIFICHE TECNICHE
(Solo LA66**, LA69**, LA74**, LN578*)
Specifiche tecniche del modulo Wireless LAN (TWFM-B006D)
StandardIEEE802.11a/b/g/n
Da 2400 a 2483,5 MHz
Gamma di frequenza
Da 5725 a 5850 MHz (Fuori dall’UE)
Potenza in uscita (Max.)
Specifiche tecniche del modulo Bluetooth (BM-LDS401)
Da 5150 a 5250 MHz
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2,4 GHz: 11 dBm
802.11n - 5 GHz: 12.5 dBm
29
ITAITALIANO
StandardBluetooth Versione 3.0
Gamma di frequenza2400 ~ 2483,5 MHz
Potenza in uscita (Max.)10 dBm o inferiore
Poiché il canale della banda utilizzato dal paese potrebbe essere diverso, l’utente non può modificare o
y
regolare la frequenza operativa; il prodotto viene impostato in base alla tabella di frequenza regionale.
Page 68
ITALIANO
0197
ITA
SPECIFICHE TECNICHE
30
(Solo LN575*, LN577*, LA62**, LA64**)
Specifiche tecniche del modulo Wireless LAN (TWFM-B006D)
StandardIEEE802.11a/b/g/n
Da 2400 a 2483,5 MHz
Gamma di frequenza
Potenza in uscita (Max.)
Poiché il canale della banda utilizzato dal paese potrebbe essere diverso, l’utente non può modificare o
y
regolare la frequenza operativa; il prodotto viene impostato in base alla tabella di frequenza regionale.
Da 5150 a 5250 MHz
Da 5725 a 5850 MHz (Fuori dall’UE)
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2,4 GHz: 11 dBm
802.11n - 5 GHz: 12.5 dBm
Page 69
SPECIFICHE TECNICHE
Le specifiche del prodotto precedentemente indicate possono subire modifiche senza preavviso in seguito
all’aggiornamento delle funzioni del prodotto.
32LA62**39LA62**42LA62**
32LA6208-ZA
MODELLI
Dimensioni
(L x A x P)
Peso
Requisiti di alimentazione
Consumo elettrico
MODELLI
Dimensioni
(L x A x P)
Peso
Requisiti di alimentazione
Consumo elettrico
MODELLI
Dimensioni
(L x A x P)
Peso
Requisiti di alimentazione
Consumo elettrico180 W
Con supporto (mm)
Senza supporto (mm)
Con supporto (kg)
Senza supporto (kg)
Con supporto (mm)
Senza supporto (mm)
Con supporto (kg)
Senza supporto (kg)
Con supporto (mm)
Senza supporto (mm)
Con supporto (kg)
Senza supporto (kg)
894 x 587 x 236968 x 629 x 2361080 x 694 x 264
894 x 537 x 79968 x 579 x 791080 x 642 x 80,5
9,710,714,7
8,69,613,4
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
1136 x 727 x 2641250 x 790 x 2971359 x 852 x 297
1136 x 673 x 82,11250 x 737 x 79,11359 x 799 x 67,2
15,621,226,3
14,219,124,2
AC 100-240 V~ 50 / 60 HzAC 100-240 V~ 50 / 60 HzAC 100-240 V~ 50 / 60 Hz
738 x 502 x 242894 x 595 x 294968 x 637 x 294
738 x 449 x 79894 x 537 x 79968 x 579 x 79
7,610,411,4
7,08,69,6
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
80 W
è fabbricato in conformità alle prescrizioni del D.M. n°548 del 28/08/95, pubblicato sulla G.U.
n°301 del 28/12/95 ed in particolare è conforme a quanto indicato nell’art. 2, comma 1 dello stesso decreto.
Questo apparecchio è fabbricato nella C.E.E nel
rispetto delle disposizioni di cui al D.M. 26/03/92ed in particolare è conforme alle prescrizioni del Art. 1 dello
stesso decreto ministeriale.
Page 77
DIAGRAMMI A BLOCCHI
Page 78
Page 79
MAKING CONNECTIONS
B-1
MAKING
CONNECTIONS
This section on MAKING CONNECTIONS mainly
uses diagrams for the LA66** models.
Antenna connection
ANTENNA/
CABLE IN
English
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
Italiano
Collegare il televisore all’antenna centralizzata con
un cavo RF (75 Ω).
NOTA
yUtilizzare uno sdoppiatore del segnale per
usare più di 2 televisori.
ySe la qualità dell’immagine è scarsa,
installare correttamente un amplificatore del
segnale per migliorarla.
ySe la qualità dell’immagine è scarsa con
un’antenna collegata, provare a riallineare
l’antenna nella direzione corretta.
yIl cavo e il convertitore dell’antenna non
sono in dotazione.
yAudio DTV supportato: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
NOTE
yUse a signal splitter to use more than 2 TVs.
yIf the image quality is poor, install a signal
amplifier properly to improve the image quality.
yIf the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
yAn antenna cable and converter are not
supplied.
ySupported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
Page 80
MAKING CONNECTIONS
B-2
Satellite dish connection
(Only satellite models)
13/18 V
700 mA Max
LNB
Satellite IN
English
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
Italiano
Collegare la TV a un’antenna satellitare e a una
presa satellitare con un cavo RF satellitare (75 Ω).
HDMI connection
DVD/ Blu-Ray / HD Cable
Box / HD STB / PC
(*Not Provided)
HDMI
(MHL)
3
/DVI IN
2
(ARC)
1
English
Transmits the digital video and audio signals from
an external device to the TV. Connect the external
device and the TV with the HDMI cable as shown.
Choose any HDMI input port to connect. It does
not matter which port you use.
NOTE
yIt is recommended to use the TV with the
HDMI connection for the best image quality.
yUse the latest High Speed HDMI™ Cable
with CEC (Customer Electronics Control)
function.
yHigh Speed HDMI™ Cables are tested to
carry an HD signal up to 1080p and higher.
ySupported HDMI Audio format : Dolby
Digital, DTS, PCM (Up to 192 KHz, 32KHz/4
4.1KHz/48KHz/88KHz/96KHz/176KHz/192K
Hz)
Page 81
MAKING CONNECTIONS
B-3
Italiano
Il segnale digitale audio e video viene trasmesso
da un dispositivo esterno al televisore. Collegare il
dispositivo esterno e il televisore mediante il cavo
HDMI come mostrato nell’illustrazione di seguito.
Scegliere una porta di ingresso HDMI per il
collegamento. La scelta della porta è libera.
NOTA
ySi consiglia di utilizzare il televisore con il
collegamento HDMI per ottenere la migliore
qualità delle immagini.
yUtilizzare un cavo HDMI™ ad alta velocità
dotato dei requisiti più recenti con funzione
CEC (Customer Electronics Control).
yI cavi HDMI™ ad alta velocità sono testati
per trasmettere un segnale HD fino a 1080p
e superiore.
SIMPLINK and ARC must be connected
using HDMI/DVI IN 1 (ARC) port.
When connected with a high-speed HDMI
y
cable, the external audio device that
supports ARC outputs optical SPDIF without
additional optical audio cable and supports
the SIMPLINK function.
Italiano
Per il collegamento di un dispositivo
y
audio esterno che supporta le funzionalità
SIMPLINK e ARC, usare la porta HDMI/DVI
IN 1 (ARC).
Se si effettua il collegamento con un cavo
y
HDMI ad alta velocità, il dispositivo audio
esterno che supporta ARC trasmette
il segnale SPDIF senza il cavo ottico
aggiuntivo e supporta la funzione SIMPLINK.
Page 82
MAKING CONNECTIONS
B-4
DVI to HDMI connection
(MHL)
3
/DVI IN
2
WHITE
RED
L
L/MONO
(ARC)
1
(*Not Provided)
Italiano
Il segnale digitale video viene trasmesso da
un dispositivo esterno al televisore. Collegare
il dispositivo esterno e il televisore mediante il
cavo DVI-HDMI come mostrato nell’illustrazione
di seguito. Per trasmettere un segnale audio,
collegare un cavo audio.
Scegliere una porta di ingresso HDMI per il
collegamento. La scelta della porta è libera.
NOTA
yA seconda della scheda grafica in uso, la
modalità DOS potrebbe non funzionare se si
utilizza un cavo da HDMI a DVI.
yQuando si utilizza il cavo HDMI/DVI, è
supportata solo l’interfaccia Single link.
AUDIO OUT
DVD/ Blu-Ray / HD Cable Box / PC
DVI OUT
English
Transmits the digital video signal from an external
device to the TV. Connect the external device and
the TV with the DVI-HDMI cable as shown. To
transmit an audio signal, connect an audio cable.
Choose any HDMI input port to connect. It does
not matter which port you use.
NOTE
yDepending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in use.
yWhen using the HDMI/DVI cable, only Single
link is supported.
Page 83
MAKING CONNECTIONS
VIDEO
AUDIO
VIDEO
AUDIO
COMPONENT IN
L
O
O
/M
AV
2
IN
B-5
Component connection
(*Not
Provided)
RED
WHITE
RED
BLUE
Italiano
Il segnale audio e video analogico viene
trasmesso da un dispositivo esterno al televisore.
Collegare il dispositivo esterno al televisore
usando un cavo component come mostrato nella
gura di seguito.
NOTA
yL’errato collegamento dei cavi può far sì che
le immagini vengano visualizzate in bianco
e nero o con colori distorti.
GREEN
DVD / Blu-Ray / HD Cable Box
English
Transmits analog video and audio signals from an
external device to the TV. Connect the external
device and the TV with a component cable as
shown.
NOTE
yIf cables are not installed correctly, it could
cause this image to display in black and
white or with distorted colours.
Page 84
MAKING CONNECTIONS
B-6
Composite connection
L
L/MONO
RED
(*Not Provided)
RED
WHITE
AV 2 IN
WHITE
YELLOW
COMPONENT IN
YELLOW
MHL connection
MHL passive cable
(*Not Provided)
(MHL)
3
/DVI IN
()
VIDEO
AUDIOLRL
DVD/ Blu-Ray / HD Cable Box / VCR
MONO
English
Transmits analog video and audio signals from
an external device o the TV. Connect the external
device and the TV with the composite cable as
shown.
Italiano
Il segnale audio e video analogico viene
trasmesso da un dispositivo esterno al televisore.
Collegare il dispositivo esterno e il televisore
mediante il cavo composite come mostrato
nell’illustrazione di seguito.
Mobile phone
English
Mobile High-definition Link (MHL) is an interface for
transmitting digital audiovisual signals from mobile
phones to television sets.
NOTE
Connect the mobile phone to the HDMI/DVI
y
IN 3 (MHL) port to view the phone screen on
the TV.
The MHL passive cable is needed to connect
y
the TV and a mobile phone.
This only works for the MHL-enabled phone.
y
Some applications can be operated by the
y
remote control.
For some mobile phones supporting MHL,
y
yo u can contr ol with the magic rem ote
control.
Remove the MHL passive cable from the TV
y
when:
- the MHL function is disabled
- your mobile device is fully charged in
standby mode
Page 85
MAKING CONNECTIONS
B-7
Italiano
Mobile High-definition Link (MHL) è un’interfaccia
per la trasmissione di segnali audiovisivi digitali dai
cellulari ai TV.
NOTA
Collegare il cellulare alla porta HDMI/DVI
y
IN 3 (MHL) per visualizzare lo schermo del
telefono sul TV.
È necessario un cavo passivo MHL per
y
collegare il TV a un cellulare.
Questa funzione è disponibile soltanto sui
y
telefoni che supportano l’interfaccia MHL.
È possibile utilizzare alcune applicazioni
y
tramite il telecomando.
Per alcuni cellulari che supportano la
y
tecnologia MHL, è possibile utilizzare il
telecomando magico.
Rimuovere il cavo passivo MHL dal TV quando:
y
- La funzione MHL è disattivata
- Il dispositivo mobile è completamente carico
in modalità standby
Audio connection
OPTICAL DIGITAL AUDIO
(*Not Provided)
OPTICAL
AUDIO IN
Digital Audio System / Sound Bar(Only
42/47LA669*)
OUT
English
You may use an optional external audio system
instead of the built-in speaker.
Digital optical audio connection
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
NOTE
yDo not look into the optical output port.
Looking at the laser beam may damage
your vision.
yAudio with ACP (Audio Copy Protection)
function may block digital audio output.
Page 86
MAKING CONNECTIONS
B-8
Italiano
È possibile utilizzare un sistema audio esterno
opzionale al posto dell’altoparlante integrato.
Collegamento audio ottico
digitale
Il segnale audio digitale viene trasmesso dal
televisore su un dispositivo esterno. Collegare il
dispositivo esterno e il televisore con il cavo audio
ottico come mostrato nell’illustrazione di seguito.
NOTA
yNon guardare nella porta dell’uscita ottica.
Guardare il raggio laser potrebbe provocare
danni alla vista.
yContenuti audio con funzione anticopia
(ACP, Audio Copy Protection) possono
bloccare l’uscita audio digitale.
USB connection
3
2
USB INHDD IN
1
HDD
English
Connect a USB storage device such as a USB
ash memory, external hard drive, or a USB
memory card reader to the TV and access the
Smart Share menu to use various multimedia les.
HUB
USB
(*Not Provided)
NOTE
ySome USB Hubs may not work. If a USB
device connected using a USB Hub is not
detected, connect it to the USB port on the
TV directly.
yConnect the external power source if your
USB is needed.
Italiano
Collegare una periferica di archiviazione USB, ad
esempio una memoria ash USB, un hard disk
esterno, o un lettore di schede di memoria USB
al televisore e accedere al menu Smart Share per
utilizzare diversi le multimediali.
NOTA
yAlcuni hub USB potrebbero non funzionare.
Se una periferica USB collegata tramite
un hub USB non viene rilevata, collegarla
direttamente alla porta USB della TV.
yCollegarsi all’alimentazione esterna se il
dispositivo USB lo richiede.
Page 87
MAKING CONNECTIONS
B-9
CI module connection
▼PCMCIA CARD SLOT▼
(*Not Provided)
Italiano
Consente la visione dei servizi codicati (a
pagamento) in modalità TV digitale. Questa
funzione non è disponibile in tutti i paesi.
NOTA
yVerificare che il modulo CI sia inserito
nello slot della scheda PCMCIA nel verso
corretto. Se il modulo non è inserito nel
modo corretto, possono verificarsi danni alla
TV e allo slot stesso.
ySe il TV non visualizza o riproduce alcun
contenuto video e audio quando è collegata
la funzione CAM (modulo di accesso
condizionale) con CI+ (Interfaccia comune
plus), contattare l’operatore del servizio
terrestre/via cavo/satellitare.
English
View the encrypted (pay) services in digital TV
mode. This feature is not available in all countries.
NOTE
yCheck if the CI module is inserted into the
PCMCIA card slot in the right direction. If the
module is not inserted properly, this can cause
damage to the TV and the PCMCIA card slot.
yIf the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
Page 88
MAKING CONNECTIONS
B-10
Headphone connection
H/P OUT
English
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
NOTE
AUDIO menu items are disabled when
y
connecting a headphone.
When changing AV MODE with a headphone
y
connected, the change is applied to video
but not to audio.(Depending on model)
Optical Digital Audio Out is not available
y
when connecting a headphone.
Headphone impedance: 16 Ω
y
Max audio output of headphone: 9 mW to 15
y
mW
Headphone jack size: 0.35 cm
y
(*Not Provided)
Italiano
Consente la trasmissione del segnale delle cufe
dalla TV a un dispositivo esterno. Collegare il
dispositivo esterno e la TV con le cufe come
mostrato nell’illustrazione di seguito.
NOTA
Le voci del menu AUDIO sono disabilitate se
y
sono collegate le cuffie.
Quando si cambia la MODALITÀ AV con le
y
cuffie collegate, la modifica viene applicata al
video ma non all’audio.(in base al modello)
L’uscita audio ottica digitale non è disponibile
y
se sono collegate le cuffie.
Impedenza cuffie: 16 Ω
y
Uscita audio max delle cufe: da 9 mW a 15
y
mW
Dimensioni jack per cufa: 0,35 cm
y
Page 89
MAKING CONNECTIONS
AV1
IN/OUT
B-11
Euro Scart connection
(*Not Provided)
English
Transmits the video and audio signals from an
external device to the TV set. Connect the external
device and the TV set with the euro scart cable as
shown.
Output
Type
Current
input mode
Digital TVDigital TV
Analogue TV, AV
HDMI
1 TV Out : Outputs Analogue TV or Digital TV
signals.
AV1
(TV Out
Analogue TVComponent
1
)
Italiano
Consente la trasmissione dei segnali audio e video
da un dispositivo esterno al televisore. Collegare il
dispositivo esterno e il televisore con il cavo Euro
Scart come mostrato nell’illustrazione di seguito.
Tipo di uscita
Modalità
di ingresso
corrente
TV digitaleTV digitale
TV analogica, AV
HDMI
1 Uscita TV: uscite segnali TV analogica o TV
digitale.
AV1
(Uscita TV
TV analogicaComponent
1
)
NOTA
yI cavi Euro Scart devono essere schermati.
yQuando si guarda il TV digitale in modalità
immagini 3D, solo i segnali di uscita 2D
possono passare attraverso il cavo SCART.
(Solo modelli 3D)
NOTE
yAny Euro scart cable used must be signal
shielded.
yWhen watching digital TV in 3D imaging
mode, only 2D out signals can be output
through the SCART cable. (Only 3D models)
Page 90
MAKING CONNECTIONS
B-12
English
Connect various external devices to the TV
and switch input modes to select an external
device. For more information of external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
NOTE
yThe external device connection may differ
from the model.
yConnect external devices to the TV
regardless of the order of the TV port.
yIf you record a TV program on a DVD
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
of recording, refer to the manual provided
with the connected device.
yRefer to the external equipment’s manual for
operating instructions.
yIf you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yIn PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
yIn PC mode, some resolution settings may
not work properly depending on the graphics
card.
Italiano
Collegare diversi dispositivi esterni al televisore e
modicare la modalità di ingresso per selezionare
un dispositivo esterno. Per ulteriori informazioni
sul collegamento di un dispositivo esterno,
consultare il manuale fornito in dotazione con
ciascun dispositivo.
È possibile collegare i seguenti dispositivi esterni:
ricevitori HD, lettori DVD, VCR, sistemi audio,
periferiche di archiviazione USB, PC, console per
videogiochi e altri dispositivi esterni.
NOTA
yIl collegamento del dispositivo esterno può
variare in base al modello.
yCollegare i dispositivi esterni al televisore
a prescindere dall’ordine della porta del
televisore.
ySe si registra un programma TV su un
registratore DVD o VCR, accertarsi di
collegare il cavo di ingresso del segnale al
televisore attraverso un registratore DVD
o VCR. Per ulteriori informazioni sulla
registrazione, consultare il manuale fornito
in dotazione con il dispositivo collegato.
yConsultare il manuale dell’apparecchiatura
esterna per le istruzioni operative.
ySe si collega una console per videogiochi
alla TV, utilizzare il cavo fornito con il
dispositivo.
yIn modalità PC, possono essere presenti
interferenze relative alla risoluzione, schemi
verticali, contrasto o luminosità. In caso
di interferenze, modificare la modalità
PC impostando un’altra risoluzione o
modificando la frequenza di aggiornamento
oppure regolare luminosità e contrasto
sul menu IMMAGINE finché non si ottiene
un’immagine nitida.
yA seconda della scheda grafica utilizzata,
alcune impostazioni di risoluzione
potrebbero non essere adatte alla modalità
PC.
Page 91
SPECIFICATIONS
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.