LG 32HL714S-W User manual

OWNER’S MANUAL

MEDICAL MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

32HL714S

www.lg.com

CONTENTS

ON CLEANING .......................................3

ENGLISH

LICENSE ...............................................4

OPEN SOURCE SOFTWARE NOTICE

INFORMATION ......................................4

ASSEMBLY AND PREPARING ...................5

USER SETTINGS ..................................15

TROUBLESHOOTING ............................29

PRODUCT SPECIFICATIONS ...................31

EXTERNAL CONTROLLER SETUP .............39

Please note that this information is for proper use and safety of the equipment. The following symbols may indicate a hazardous situation in which, if not heeded, may result in serious injury or even death to the user or others, or damage to the equipment.

WARNING

• Indicates warning and safety instructions. If not adhered to, it could result in death or serious injury to the

user or others.

CAUTION

• Indicates a hazardous situation which, if not heeded, may result in minor or moderate injury to the user or

others, or damage to the equipment.

ON CLEANING

ENGLISH

Recommended Cleaning Chemicals

• Isopropanol 70 %

• Ethanol 70 %

• 0.9 % NaCl solution

How to Use Cleaner

• Prior to cleaning, turn off the monitor and remove the power cable.

• Moisten a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1 N of force.

• The cleaner could cause serious damage if it leaks inside the monitor while cleaning.

• The display could be damaged, so only clean the parts of the monitor other than the screen's LCD panel.

• Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.

• Cleaning guidelines for displays must only be carried out by medical professionals (Doctors or Nurses),

cleaners must not be handled by patients.

LICENSE

OPEN SOURCE SOFTWARE NOTICE

Each model has different licenses. Visit

ENGLISH

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

www.lg.com

for more information on the license.

INFORMATION

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.

http://opensource.lge.com.

In addition to the source code, all referred license terms,

opensource@lge.com.

This offer is valid for

ASSEMBLY AND PREPARING

Product Composition

Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product.

Note that the product and related components may look different from those shown here.

CD (Owner's Manual / Software) /

Regulatory Manual / Cards

HDMI Cable

Power Cord AC/DC Adaptor

DisplayPort Cable

ENGLISH

CAUTION

• Always use genuine LG components to ensure safety and product performance.

• The product warranty will not cover damage or injury caused by the use of unauthorized components.

• It is recommended to use the supplied components.

ENGLISH

• If you use generic cables not certified by LG, the screen may not display or there may be image noises.

• Only use components listed below that meet the listed standard. Unauthorized components may cause

damage to and malfunction of the product.

Supported Software

Check the drivers and software supported by your product and refer to the manuals on the CD enclosed in the product package.

Drivers and Software Installation Priority

True Color Pro Recommended

Component Standard

HDMI Cable UL, Impedance 100 ohm

DisplayPort Cable UL, Impedance 100 ohm

Power Cord US – Approved Medical grade regulation

Others – Approved country safety regulation

• Except for the components listed above, only use AC/DC adaptors and components supplied by the

manufacturer.

NOTE

• The components may look different from those illustrated here.

• Without prior notice, all product information and specifications contained in this manual are subject to

change to improve the performance of the product.

• To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailer

from which you purchased the product.

• The power cord provided may differ depending upon the region.

• Required and Recommended: You can download and install the latest version from the enclosed CD or from

the LGE website (

www.lg.com

Product and LED Control buttons

1 2 3 4 5 6 7 8

Front

ENGLISH

Bottom

LED Control button Functions

ENGLISH

• Selects the input mode.

• Adjusts display mode for 2 or more screens.

• Opens the [Hot key Settings] menu.

• Adjusts the screen brightness.

• Selects and confirms menus or options

• Adjusts the screen contrast.

• Displays LED Control buttons on the front panel and opens the menu mode.

Power indicator

• The green indicator illuminates if the power is on. The arrow indicates the position of the power switch.

Power switch

• Turns the power on/off.

NOTE

• The Power button is located at the bottom right on the front of the monitor.

• If the Control Key LED is turned off, press the Control Key button to turn the Control button LED on. When the Control Key LED is turned on, you can control the Control Key functions.

Connectors

Back

2 3 4 5 6 7 8

ENGLISH

, ,

• Receives or transmits digital video signals.

• Supported SDI(Serial Digital Interface signals) format is SMPTE 259M compliant (SD) / SMPTE

292M compliant (HD) / SMPTE 425M compliant (3G) / SMPTE ST 2081-10 (6G) / SMPTE ST 2082-10 (12G).

• 12G-SDI input transmission distance: 50 M max. (When using BELDEN1694A cable) / 70 M max.

(When using CANARE UHD 5.5C cable)

• This model supports 12G-SDI video using SFP module.

• Recommended SFP module types.

- Pluggable – SFP Type

- Standard – Video format SDI

- Host Pin configuration – Non-MSA

- Optical Fiber Number of Input – 1

- Optical Fiber Number of Output – 1

- Connector – LC Type

- Wavelength Receiver – 1270 nm ~ 1610 nm

- Wavelength Transmitter – 1310 nm

- Serial Data Rate(MAX) – 11.880 Mbps

- Vendor – Embrionix

Potential Equalization Conductor

• Connect an equipotential plug.

• Connect the RS-232C terminal with an external device to control the monitor.

• Connect an AC/DC adapter.

• Receives or transmits digital video signals.

• Connect a up to 5-meter cable to transmit a duplicated screen to a monitor.

• Input digital video signal.

• Using a DVI to HDMI / DisplayPort to HDMI cable may cause compatibility issues.

• Use a certified cable that displays the HDMI logo. The screen may not appear or a connection error

could occur if a non-certified cable is used.

• Recommended HDMI cable types

- High speed HDMI®/™ cable

- High speed HDMI®/™ Ethernet cable

• Receives or transmits digital video signals.

• There may be no video output depending on the DisplayPort version of your PC.

• A cable with DisplayPort 1.2 specifications is recommended when using a Mini DisplayPort to

DisplayPort cable.

• Used for HW Calibrator (Optional Accessory) connection.

• Connect peripheral device to the USB input port.

• A keyboard, mouse, or USB storage device can be connected.

• To use USB 2.0, connect the A-B type USB 2.0 cable to the PC.

CAUTION

Cautions When Using a USB Storage Device

• A USB storage device which has a built-in automatic recognition program or uses its own driver

might not be recognizable.

• Some USB storage devices may not be supported or may not work properly.

• It is recommended to use a USB hub or hard disk drive with power supplied. (If the power supplied

is not enough, the USB device may not be detected properly.)

- This USB port is used only for service.

NOTE

• All signal out terminals (SDI, DVI, etc.) output a signal when the power switch of the monitor is on. When the

power switch is off, no signal is outputted.

• This monitor supports the feature.

* : A feature that allows you to add a device to your computer without the need for physical

device configuration or user intervention.

ENGLISH

Installing the Monitor

Cable connection and organize

ENGLISH

Before connecting the connectors, remove the back door as shown below.

1 O nce the screws are removed, lift the back door in the direction of the arrow below to remove it. The back

door is held in place with a magnet.

2 After installing the cables, tidy them up using the cable holders.

3 O nce the back door is attached, assemble it using the screws.

CAUTION

• When the back door is attached to the monitor, the monitor meets water resistance standards. Do not use the

monitor with the back door detached, as the water resistance capability is not guaranteed without the door.

Installing on the Wall

Install the monitor at least 100 mm away from the wall on each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local dealer. Please refer to the manual to install and set up a tilting wall mounting bracket.

100 mm

Installing the Wall Mount Plate

This monitor meets the specifications for the wall mount plate or other compatible devices.

Wall Mount (mm) Standard screw Required screws Wall mount plate (optional)

100 x 100

M4 x L10

LSW140

ENGLISH

100 mm

To install the monitor to a wall, attach a wall mount plate (optional) to the back of the monitor.

Make sure that the wall mount plate (optional) is securely fixed to the monitor and to the wall.

100 mm

NOTE

• A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not

liable for any accidents relating to the use of non-standard screws.

• The wall mount kit includes the installation guide and all necessary parts.

• The wall mounting bracket is optional. You can obtain optional accessories from your local dealer.

• The length of the screw may differ for each wall mounting bracket. If you use screws longer than the standard

length, it may damage the inside of the product.

• For more information, please refer to the user manual for the wall mounting bracket.

• Be careful not to apply too much force while mounting the wall mount plate as it may cause damage to the

screen.

• Remove the stand before installing the monitor on a wall mount by performing the stand attachment in

reverse.

CAUTION

• Disconnect the power cord before moving or installing the monitor. There is risk of electric shock.

• Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could

ENGLISH

lead to injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.

• To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation

instructions.

• Applying excessive force when tightening screws may damage the monitor. Such damage is not covered by

the product warranty.

• Use the wall mounting bracket and screws that confirm to VESA standards. Damage caused by the use or

misuse of inappropriate components is not covered by the product warranty.

• When measured from the back of the monitor, the length of each installed screw must be 8 mm or less.

Wall mount plate

Back of the monitor

Wall mount plate

Back of the monitor

Screw specifications

: M4 x L10

Precautions for Connecting the Power Cord

100-240 V ~

• Make sure to use the power cord that is provided in the product package. Connect the cord to a grounded

power outlet.

• If you need another power cord, please contact your local dealer or the nearest retail store.

Max. 8 mm

USER SETTINGS

Activating the Quick Menu

1 Press ( ) to activate the LED Control Button. When the LED Control button is activated, press ( ) to show the OSD Quick Menu. 2 Among the LED Control Button, press to move to the left or right or to move to the bottom or top or to set options. 3 In order to exit from the OSD Menu, press the LED Control Button ( ) or select [Exit].

The applicable setting options are as shown below.

Quick Menu Settings Explanation

[Exit]

[Input]

[Picture Mode] Selects the [Picture Mode].

[Gamma] Selects the screen's [Gamma].

[Color Temp] Selects the screen's [Color Temp].

[All Settings] Enters the All Settings menu.

CAUTION

• The Monitor OSD (On Screen Display) may differ from the description in the User Manual.

Closes the Quick Menu.

Selects the applicable input mode.

NOTE

• If the [Picture Mode] is not the [Custom] mode, [Gamma] and [Color Temp] will be deactivated.

ENGLISH

[Quick Settings]

1 Press ( ) to activate the LED Control Button. When the LED Control Button is activated, press ( ) and select [All Settings] to show the complete OSD Menu. 2 Among the LED Control Button, press to move to the left or right or to move to the bottom or top to go to the [Quick Settings].

ENGLISH

3 Configure the options following the instructions that appear in the bottom right corner. 4 To configure an upper menu or another item, press the LED Control Button or press to move to the settings. 5 In order to exit from the OSD Menu, press the LED Control Button ( ) or press .

The applicable setting options are as shown below.

[All Settings] > [Quick

Settings]

[Brightness]

Adjusts screen brightness.

Explanation

NOTE

• Press the button to toggle between [Turn on 'Brightness Stabilization']/[Turn off 'Brightness Stabilization'].

• When [Brightness Stabilization] is [On], the [Brightness] adjustment function is deactivated.

• When [Brightness Stabilization] is [On], [SMART ENERGY SAVING] and [DFC] functions are deactivated.

• When [Picture Mode] is set as [DICOM], or [Gamma] is set as [DICOM Gamma Curve] Setting, the [Brightness] adjustment function is deactivated.

[Contrast]

[Color Temp] Set your own color temperature. ([Custom], [6500K], [7500K], [9300K], [Manual])

[Hot key Settings] Designate a hotkey for screen image settings. After setting the hotkey, use the hotkey in the LED Control Button to enable the set menu. ([PIP Size], [Gamma], [Mono], [Color Temp], [Black

Adjusts the color contrast of the screen.

Stabilizer], [Screen Zoom], [Off])

[Hotkey 1] Select a function to use with [Hotkey 1].

[Hotkey 2] Select a function to use with [Hotkey 2].

+ 35 hidden pages