LG 24MP77M SERVICE MANUAL

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

COLOR MONITOR

SERVICE MANUAL

CHASSIS NO. : LM13C

MODEL:

CAUTION

BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL68742422 (1502-REV01) Printed in China

24MP77*MM

CONTENTS

CONTENTS .............................................................................................. 2

PRECAUTION............................................................................................3

SERVICING PRECAUTIONS.....................................................................4

SPECIFICATIONS......................................................................................6

TIMING CHART .......................................................................................11

ADJUSTMENT .........................................................................................14

BLOCK DIAGRAM...................................................................................18

TROUBLE SHOOTING ............................................................................19

EXPLODED VIEW .................................................................................. 22

SVC. SHEET ...............................................................................................

- 2 -

LGE Internal Use Only

PRECAUTION

WARNING FOR THE SAFETY-RELATED COMPONENT.

• There are some special components used in LCD monitor that

are important for safety. These parts are marked on the schematic diagram and the Exploded View. It is essential that these critical parts should be replaced with the manufacturer’s specified parts to prevent electric shock, fire or other hazard.

• Do not modify original design without obtaining written permission from manufacturer or you will void the original parts and labor guarantee.

TAKE CARE DURING HANDLING THE LCD MODULE WITH BACKLIGHT UNIT.

• Must mount the module using mounting holes arranged in four corners.

• Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.

• Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel.

• Protect the module from the ESD as it may damage the electronic circuit (C-MOS).

WARNING

BE CAREFUL ELECTRIC SHOCK !

• If you want to replace with the new backlight (CCFL) or LIPS part, must disconnect the AC power because high voltage appears at inverter circuit about 650Vrms.

• Handle with care wires or connectors of the inverter circuit. If the wires are pressed cause short and may burn or take fire.

Leakage Current Hot Check Circuit

AC Volt-meter

Good Earth Ground such as WATER PIPE,

To Instrument's exposed METALLIC PARTS

When 25A is impressed between Earth and 2nd Ground for 1 second, Resistance must be less than 0.1

*Base on Adjustment standard

0.15uF

1.5 Kohm/10W

CONDUIT etc.

• Make certain that treatment person’s body are grounded through wrist band.

• Do not leave the module in high temperature and in areas of high humidity for a long time.

• The module not be exposed to the direct sunlight.

• Avoid contact with water as it may a short circuit within the module.

• If the surface of panel become dirty, please wipe it off with a softmaterial. (Cleaning with a dirty or rough cloth may damage the panel.)

CAUTION

Please use only a plastic screwdriver to protect yourself from shock hazard during service operation.

- 3 -

LGE Internal Use Only

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service

manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication.

NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or re-connecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) is opropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500ºF to 600ºF.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500ºF to 600ºF) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500ºF to 600ºF)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 4 -

LGE Internal Use Only

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

- 5 -

LGE Internal Use Only

1. General Specification

No Item

1 Customer BRAN 2 3 Sale region

4 Feature 24”/

5 Chassis Nam

User Model N

General Scope

Power Cord

ame

e LM13C

External SW

&Adj.

Function OSD

Signal

Cable

(D-SUB)

SPECIFICATIONS

Content Remark

27MP77*M/24MP77*M Refer to Suffix standard

27” Wide LCD MONITOR

Joystick New OSD (Menu, Picture Mode, Input, Power off)

,DDC2B,DDC2AB, HDCP, Control Lock,

Original Ratio / Wide, Black level, Smart Energy Saving Screen Split, SUPER RESOLUTION+，Color Wizard, Reader mode, LG Color Cloning

gth : 1.5±0.05 M

Len Shape : Wall-out Color : Black

Length : 1.5m Shape : Detachable Type Color : Black Pin : Triple Row, 15 Pin D-Sub

Refer to Suffix

standard and power

cord table

Refer to Suffix

standard

Length : 1.5m

Signal Cabl

(DVI)

8 Cable

9 Power

Applying

P/N: EAJ631476

Signal Cabl

(HDMI)

Audio

module list

Shape : Detachable Type Color : Black Pin : Triple Row, 24 Pin DVI

Length : 1.8m

Shape : Detachable Type Color : Black Pin : 19Pin HDMI

Length Color: Black , Pin:2P

TV Length

AC100~240V 50~60Hz,1.0A Max

Input: Output: DC 19V 1.7 A

P/No: EAJ62507601

: 1.5

: ,Shape : ,Color: ,Pin Do not Support

Specification:

LM270WF7-SSA1 FHD 2

7.0INCH 1920X1080 250 LM238WF2-SSF1 FHD

24INCH 1920X1080

250CD

Do not Support

Refer to Suffix

standard

Do not Support

Refer to Suffix

standard

11 Speak

P/N: EAB6

3628201

- 6 -

Typ:5W*5W

LGE Internal Use Only

2. Mechanical specification

Palleti

zing

No Item

Product

mension

Product

Wei

tainer

Con

ght

Quantity

4 Stand

Assy

5 Appeara

Content Remark Width (W) Length (D) Height (H) Before Packi

After

Packin Only SET Head part With

OX 4.2 kg

Individual or

Type Base detachable Size (W D x H) Tilt D

egree -3°(+/-3°) ~ 20°(+/-3°)

orce 0.8~1.2 kgf

Tilt f Foldin

Degree

ce General Refer to Standard of LG(56)G2-1011

54.2 cm

18.2 cm

5.2 cm

42.8 cm

32.8 cm

With stand Without stand

61.0 cm 38.8 cm 12.6 cm

3.5 kg

2.9 kg

20ft 4

Indi.

972 72

20.1cm * 18.2cm * 1.9cm

Pallet Indi. Pallet

0 1962 1600

20.1cm * 18.2cm * 15.5cm

With stand

Without stand

Only stand base Stand asssy

None

3. Optical Character

No Item C

Viewi

ng Angle

<CR≥10>

Lumina

nce(휘도)

Horizontal(R/L) : +85º/-85º ( (Typ.)

(Top/Bottom) : +80º/-80º (Typ.)

Vertical

Average Luminance (cd/m2)

Average Lu (cd/m2)

Average

Luminance (cd/m2)

Luminan

Uniformity

t Ratio(명암 비)

ontras

600(MIN), 1000(TYP), DFC->5,000,000:1(Typ.)

. Low : 9 ms ~ 11 ms

4 Resp

CIE Col

Coordinates

(색 좌표)

Light

onse Time

Leakage

hite

White

RED

GREEN

BLUE

-. Middle : 7 ms ~ 9 ms

-. High : 5.5 ms ~ 6.5 ms

WY 0.32

Y 0.311

Y 0.29

WY 0.36

riteria Remark

150 (min) (Full white pattern, 0.7V)

minance

200(min),250 (Typ.) (Full white pattern, 0.7V)

150(min) (Full white pattern, 0.7V)

75%(min),

Condition: Do not visible at 300 Lux

Minimum

-0.03

Typ

Typ-0.03

Typ-0

.03

Normal

0.313

0.302

0.283

0.365

0.353

0.653

0.336

0.322

0.609

0.152

060

- 7 -

Medium

Warm

Cool

Maximum

Typ+0.03

Typ+0.03 Read1

Typ+0.03 Read2

Typ+0.03

Warm

(6500K)

Medium (8000K)

(9300K)

Warm

(6500K)

Cool

LGE Internal Use Only

4. Engineering Specification

Support

2 Opera

Res

4 Inpu

ed Sync. Type

ting Frequency

ion

olu

t Voltage Voltage :100 – 240 Vac, 50 or 60Hz, 1.0A

Separate Sync., Digital

Analog/ Digital

HDMI

Analog/ Digital

HDMI

Horizontal 30 83kHz∼ Vertical Ho

56 75 Hz∼

rizontal 30 83kHz∼ Vertical 56 61 Hz∼ Max. 1920×1080 @ 60Hz

Recommen Max. 1920×1080 @ 60Hz Recommen

d 1920×1080 @ 60Hz

5 Inrus

h Current Cold Start : 50 A Hot : 120 A

Operating Condition

On Mode O

Sleep Mo

Off Mod

(Power switch off)

Smart Energy

Saving

EPA

MTBF

Using

Altitude

Environ 0peratin

Sync (H/V)

Video LED Wattage

Test condition

1.1920x1080@60Hz

2. burst pattern

3. 100~240V

4. After aging 30min

n/On Active White

22W (MAX :26 W )24 inch

측정방법) 제어판 à 전원 옵션에서 디스플

Off/On On/Off Off/Off

Off White Blinking <0.3W

레이 끄기와 PC를 절 전모드로 하기 두가지 설정이 있는데, PC를 절전모드로 하기만 선 택하고 측정해야 함.

- - Off <0.3W

Efficiency :

Low:10%~20

-Test Condition (1)

High

/Low/Of

Low

White

High:20%~30

Low：>3W

High:

>5W(24”)

High:>5W(27’’

)

200nits ：

23W(27inch) 21W(24inch)

margin >7%

Worst :margin

,000 HRS with

3 0 90%

Lamp Life : 30,000 Hours(Min)

Confidence level

5,000 m (for Reliability) 3,000m(for FOS)

Temperature

10 °C ~ 35 °C

- 8 -

LGE Internal Use Only

ish/Ge

rman/French/Esperanto

ment

nditio

Storage

Humidity 10% ~ 80% Temperature Humidit

y 5% ~ 90% non-condensing

-20 °C ~ 60 °C

Contrast 0~100

Volume 0~100

BRIGHTNESS 0 ~ 100

MENU (Monitor block)

ORIGIN

TEMP

COLOR

RATIO

BLACK LEVEL

LANGUAGE

FACTORY

ESET

WARM

PRESET

MEDIUM

COOL

RED

USER

GREEN

BLUE

WIDE

ORIGINAL

▶

HIGH / LOW

(BLACK LEVEL enable at HDMI

input)

▶

ENGLISH

▶ NO( /YES )

17 Language: English, Germanic, French, Spanish, Italian, Swedish, Finnish, Portuguese Brazilian Portuguese, Polish, Russian, Greek, Chinese, Japanese, Korean, Ukrainian

Hindi

CHANNEL 2~69(AIR) / 1 ~ 125(CABLE)

Function Support: No

OSD

CHANNEL

ADD/DEL ADD/DELETE

AUTO CHANNEL ON/OFF

SELECT AIR/CABLE

FINE TUNE 0 ~ 100

CONTRAST 0~100

0~100

~10

0~100

/OFF

Function Support: No

unction Support:

F No

MENU (AV/TV bl

ock)

ADJUSTMEN

AUDIO

BRIGHTN S

SHARPNESS 0

COLOR

TINT

BASS

TREBL

MUTE ON

SOUND

MONO/ST

LAN

EREO

GUAGE▶

Engl

n/Korean…

SETUP

Italia

IMAGE S

OSD POSITI

IZE ▶ FULL/1:1

TRANSPAREN CY

~100

Function Support: No

- 9 -

LGE Internal Use Only

+ 18 hidden pages

LG 24MP77M SERVICE MANUAL

Specifications and Main Features

Frequently Asked Questions

User Manual