LG 24MP55VQ-W Owner’s Manual
ENGLISH
OWNER’S MANUAL
IPS LED MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
IPS LED MONITOR MODEL
22MP55VQ
23MP55VQ
24MP55VQ
27MP55VQ
www.lg.com
ENGLISH
ENG
TABLE OF CONTENTS
2
CONTENTS
3 LICENSE
4 ASSEMBLING AND PREPAR-
ING
4 Unpacking
5 Parts and buttons
6 Moving and Lifting the Monitor
7 Setting up the Monitor set
7 - Attaching the Stand Base
8 - Detaching the Stand Base
9 - Mounting on a table
9 - Using the cable holder
11 - Mounting on a wall
12 USING THE MONITOR SET
12 Connecting to a PC
12 - D-SUB connection
12 - DVI-D connection
12 - HDMI connection
13 Connecting to AV Devices
13 - HDMI connection
13 Connecting to External Devices
13 - Peripheral device connection
25 - DUAL DISPLAY
25 - DUAL WEB
26 TROUBLESHOOTING
28 SPECIFICATIONS
28 22MP55VQ
29 23MP55VQ
30 24MP55VQ
31 27MP55VQ
32 Preset Modes (Resolution)
32 Indicator
33 PROPER POSTURE
33 Proper posture for using the Monitor set.
15 CUSTOMIZING SETTINGS
16 Customizing Settings
16 - Menu Settings
17 - Picture
18 - Color
19 - Display
19 - Audio
20 - Others
21 READER Setting
22 FUNC. Setting
22 - SUPER ENERGY SAVING
23 - Picture Mode
24 - SUPER RESOLUTION +
LICENSE
3
LICENSE
Each model has different licenses. Visit www.lg.com for more information on the license.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
ENGLISH
ENG
ASSEMBLING AND PREPARING
4
ENGLISH
ENG
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
CD(Owner's Manual) /
Card
D-SUB Cable
(This cable is not
included in all
countries.)
DVI-D Cable
(This cable is not
included in all
countries.)
or
HDMI Cable
(This cable is not
included in all
countries.)
Power Cord AC-DC Adapter AC-DC Adapter
( Depending on the country ) ( Depending on the country )
Stand Body
Stand Body
Two Screws
Stand Base
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
y
Any damages or injuries by using unapproved accessories are not covered by the warranty.
y
NOTE
The accessories supplied with your product may vary depending on the model.
y
Product specifications or contents in this manual may be changed without prior notice due to upgrade
y
of product functions.
Parts and buttons
READER
READER
ASSEMBLING AND PREPARING
Power Indicator
Lighting On: Turned on
y
Lighting Off: Turned off
y
(Power Button)
5
ENGLISH
ENG
Button (See p.15)
Connection panel (See p.12)
ASSEMBLING AND PREPARING
6
ENGLISH
ENG
Moving and Lifting the Monitor
When moving or lifting the monitor, follow these
instructions to prevent the monitor from being
scratched or damaged and to ensure safe transportation regardless of its shape or size.
It is advisable to place the monitor in the
y
original box or packing material before attempting to move it.
Before moving or lifting the monitor, discon-
y
nect the power cord and all cables.
Hold the top and bottom of the monitor frame
y
firmly. Do not hold the panel itself.
When holding the monitor, the screen should
y
face away from you to prevent it being
scratched.
When moving the monitor, avoid any strong
y
shock or vibrations to the product.
When moving the monitor, keep it upright,
y
never turn the monitor on its side or tilt it
sideways.
CAUTION
As far as possible, avoid touching the moni-
y
tor screen. This may result in damage to the
screen or some of the pixels used to create
images.
ASSEMBLING AND PREPARING
7
Setting up the Monitor set
Attaching the Stand Base
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.
2
22MP55VQ/23MP55VQ/24MP55VQ
1
Attach the
Attach the
2
Tighten the screw to the right.
3
Stand Body
Stand Body
Stand Base
to the monitor set.
.
27MP55VQ
Attach the
1
Use two screws to fix the
2
monitor set.
3
Attach the
4
Tighten the screw to the right .
Stand Body
Stand Body
Stand Base
to the monitor set.
Stand Body
.
and
ENGLISH
ENG
Stand Base
Stand Body
Stand Base
ASSEMBLING AND PREPARING
8
ENGLISH
ENG
Detaching the Stand Base
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
22MP55VQ/ 23MP55VQ /24MP55VQ
2
Pull out the
1
from the monitor set.
Turn the screw to the left.
2
3
Pull out the
Stand Body
Stand Body
Stand Base
and
.
Stand Base
27MP55VQ
1
Turn the screw to the left.
2
Pull out the
3
Remove two screws and pull out the
Body
Stand Body
Stand Base
Stand Base
from the monitor set.
from the
Stand Body
Stand
.
Stand Base
Stand Body
Stand Base
Stand Body
CAUTION
This illustration depicts the general model of
y
connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down holding
y
only the stand base. The product may fall
and get damaged or injure your foot.
ASSEMBLING AND PREPARING
9
Mounting on a table
Lift and tilt the Monitor set into its upright
1
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
10 cm
10 cm
Press (Power) button on the bottom switch
3
panel to turn the power on.
CAUTION
Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.
Using the cable holder
ENGLISH
ENG
Connect the AC-DC Adapter and Power Cord
2
to a wall outlet.
or
Cable holder
ASSEMBLING AND PREPARING
10
WARNING
ENGLISH
ENG
When you adjust the angle, do not hold the
bottom of the Monitor set frame as shown on
the following illustration, as may injure your
fingers.
Do not touch or press the screen when
adjusting the angle of the monitor.
Do not hold this set like below picture.Monitor
screen can detach from stand base and injure
your body.
27MP55VQ
NOTE
Tilt from +20 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
Front
Using the Kensington security system
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit
Connect the Kensington security system cable
between the Monitor set and a table.
http://www.kensington.com
Rear
.
22MP55VQ/23MP55VQ/24MP55VQ
NOTE
Tilt from +20 to -3 degrees up or down to adjust
the angle of the Monitor set to suit your view.
Front
Rear
NOTE
The Kensington security system is optional.
You can obtain it from most electronics stores.
ASSEMBLING AND PREPARING
11
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
10 cm
10 cm
If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
Please, Use the screw and wall mount interface
1
in accordance with VESA Standards.
If you use screw longer than standard, the
2
monitor might be damaged internally.
10 cm
10 cm
Model
VESA (A x B) 75 x 75 100 x 100
Standard screw M4
Number of screws 4
22MP55VQ
23MP55VQ
24MP55VQ
27MP55VQ
CAUTION
Disconnect the power cord first, and then
y
move or install the Monitor set. Otherwise
electric shock may occur.
If you install the Monitor set on a ceiling or
y
slanted wall, it may fall and result in severe
injury.
Use only an authorized LG wall mount
y
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
y
cause damage to the Monitor set and void
your warranty.
Use only screws and wall mounts that
y
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
Screw length from outer surface of back
y
cover should be under 8mm.
Wall mount Pad
Back Cover
Wall mount Pad
Back Cover
Standard screw
ENGLISH
ENG
If you use improper screw, the product might be
3
damaged and drop from mounted position. In
this case, LG Electronics is not responsible for
it.
VESA compatible only with respect to screw
4
mounting interface dimensions and mounting
screw specifications.
Please use VESA standard as below.
5
784.8 mm (30.9 inch) and under
y
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
y
* Please use VESA standard wall mount pad
and screws.
Max.8mm
NOTE
Use the screws that are listed on the VESA
y
standard screw specifications.
The wall mount kit will include an installation
y
manual and necessary parts.
The wall mount bracket is optional. You can
y
obtain additional accessories from your local
dealer.
The length of screws may differ depending
y
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
y
instructions supplied with the wall mount.
Loading...