LG 24EN43VS, 24EN43VS-B Owner's Manual

ENGLISH
OWNER’S MANUAL
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODEL
24EN43VS
www.lg.com
ENGLISH
ENG
TABLE OF CONTENTS
CONTENTS
3 ASSEMBLING AND PREPAR-
ING
3 Unpacking 4 Parts and buttons 5 Setting up the Monitor set 5 - Attaching the Stand Base
5 - Detaching the Stand Base 6 - Mounting on a table 6 - Using the cable holder 8 - Mounting on a wall
9 USING THE MONITOR SET
9 Connecting to a PC 9 - D-SUB connection 9 - DVI-D connection 9 - HDMI connection
11 CUSTOMIZING SETTINGS
11 Customizing Settings 12 - Menu Settings 13 - Picture 14 - Color 15 - Display 15 - Volume 16 - Others 17 MY KEY Setting 18 FUNC. Setting 18 - Picture Mode 19 - SUPER ENERGY SAVING 20 - DUAL DISPLAY 20 - DUAL WEB 21 - MY KEY Setting
22 TROUBLESHOOTING
24 SPECIFICATIONS
24 24EN43VS 25 Preset Modes (Resolution) 25 HDMI TIMING 25 Indicator
26 PROPER POSTURE
26 Proper posture for using the Monitor set.
ASSEMBLING AND PREPARING
3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
CD(Owner's Manual) /
Card
D-SUB Cable
or
DVI-D Cable
(This cable is not included
in all countries.)
ENGLISH
ENG
Power Cord AC-DC Adapter AC-DC Adapter
( Depending on the country ) ( Depending on the country )
Stand Body
Stand Base
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
y
Any damages or injuries by using unapproved accessories are not covered by the warranty.
y
NOTE
The accessories supplied with your product may vary depending on the model.
y
Product specifications or contents in this manual may be changed without prior notice due to upgrade
y
of product functions.
ENGLISH
ENG
ASSEMBLING AND PREPARING
4
Parts and buttons
Power Indicator
Lighting On: Turned on
y
Lighting Off: Turned off
y
(Power Button)
Button (See p.11)
Connection panel (See p.9)
Setting up the Monitor set
Attaching the Stand Base
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.
1
Attach the Stand Body to the monitor set.
2
Attach the Stand Base.
2
Tighten the screw to the right with a coin.
3
ASSEMBLING AND PREPARING
Detaching the Stand Base
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
1
2
Stand Body
Pull out the Stand Body and Stand Base from the monitor set.
2
Turn the screw to the left with a coin. Pull out the Stand Base.
3
5
ENGLISH
ENG
Stand Body
Stand Base
Stand Base
Stand Body
Stand Base
CAUTION
This illustration depicts the general model of
y
connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding
y
only the stand base. The product may fall and get damaged or injure your foot.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Mounting on a table
Lift and tilt the Monitor set into its upright
1
position on a table. Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
10 cm
10 cm
Press (Power) button on the bottom switch
3
panel to turn the power on.
CAUTION
Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.
Using the cable holder
Connect the AC-DC Adapter and Power Cord
2
to a wall outlet.
or
Cable holder
ASSEMBLING AND PREPARING
7
WARNING
When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.
Do not touch or press the screen when adjusting the angle of the monitor.
Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.
Using the Kensington security system
The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit
Connect the Kensington security system cable between the Monitor set and a table.
http://www.kensington.com
.
NOTE
ENGLISH
ENG
NOTE
Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
Front Rear
The Kensington security system is optional. You can obtain it from most electronics stores.
ASSEMBLING AND PREPARING
8
ENGLISH
ENG
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
10 cm
10 cm
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.
Please, Use the screw and wall mount interface
1
in accordance with VESA Standards.
If you use screw longer than standard, the
2
monitor might be damaged internally.
If you use improper screw, the product might be
3
damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.
VESA compatible.
4
Please use VESA standard as below.
5
784.8 mm (30.9 inch) and under
y
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
y
* Please use VESA standard wall mount pad
and screws.
10 cm
10 cm
Model
VESA (A x B) S
tandard screw M4
Number of screws 4
24EN43VS
100 x 100
CAUTION
Disconnect the power cord first, and then
y
move or install the Monitor set. Otherwise electric shock may occur. If you install the Monitor set on a ceiling or
y
slanted wall, it may fall and result in severe injury. Use only an authorized LG wall mount
y
and contact the local dealer or qualified personnel. Do not over tighten the screws as this may
y
cause damage to the Monitor set and void your warranty. Use only screws and wall mounts that
y
meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
NOTE
Use the screws that are listed on the VESA
y
standard screw specifications. The wall mount kit will include an installation
y
manual and necessary parts. The wall mount bracket is optional. You can
y
obtain additional accessories from your local dealer. The length of screws may differ depending
y
on the wall mount. Be sure to use the proper length. For more information, refer to the
y
instructions supplied with the wall mount.
UsInG tHe MonItoR set
Connecting to a PC
DVI-D connection
USING THE MONITOR SET
9
ENGLISH
ENG
Your Monitor set supports Plug & Play*.
y
*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.
D-SUB connection
Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.
Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.
HDMI connection
Transmits the digital video and audio signals from your PC or A/V to the Monitor set. Connect the PC or A/V and the Monitor set with the HDMI cable as shown in the following illustrations.
NOTE
When using a D-Sub signal input cable
y
connector for Macintosh
Mac adapter
y
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.
NOTE
If you use HDMI PC, it can cause compatibility
y
problem.
Loading...
+ 18 hidden pages