LG 19EN43S, 19EN43T, 20EN43S, 20EN43T, 22EN43S User Guide

...

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODEL

19EN43S 19EN43T 20EN43S 20EN43T 22EN43S 22EN43T 23EN43S 23EN43T

24EN43T

www.lg.com

ENGLISH

ENG

TABLE OF CONTENTS

3 ASSEMBLING AND PREPAR-

ING

24 SPECIFICATIONS

3 Unpacking 4 Parts and buttons 5 Setting up the Monitor set 5 - Attaching the Stand Base 5 - Detaching the Stand Base 6 - Mounting on a table 6 - Using the cable holder 8 - Mounting on a wall

9 USING THE MONITOR SET

9 Connecting to a PC 9 - D-SUB connection

11 CUSTOMIZING SETTINGS

12 Customizing Settings 12 - Menu Settings 13 - Picture 14 - Color 15 - Display 16 - Others 17 MY KEY Setting 18 FUNC. Setting 18 - Picture Mode 19 - SUPER ENERGY SAVING 20 - DUAL DISPLAY 20 - DUAL WEB 21 - MY KEY Setting

24 19EN43S 25 19EN43T 26 20EN43S

20EN43T27 28 22EN43S 29 22EN43T 30 23EN43S

31 23EN43T 32 24EN43T

33 Preset Modes (Resolution) 34 Indicator

35 PROPER POSTURE

35 Proper posture for using the Monitor set.

22 TROUBLESHOOTING

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

DVI-D Cable

CD(Owner's Manual) /

Card

D-SUB Cable

(19EN43T/22EN43T/22EN43T/

23EN43T/24EN43T)

(This cable is not included

in all countries.)

ENGLISH

ENG

Power Cord AC-DC Adapter AC-DC Adapter

( Depending on the country ) ( Depending on the country )

Stand Body

Stand Base

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

y

Any damages or injuries by using unapproved accessories are not covered by the warranty.

y

NOTE

The accessories supplied with your product may vary depending on the model.

y

Product specifications or contents in this manual may be changed without prior notice due to upgrade

y

of product functions.

ENGLISH

Power Indicator

Lighting On: Turned on

Button (See p.11)

(Power Button)

ENG

ASSEMBLING AND PREPARING

Parts and buttons

19EN43S

22EN43S 23EN43S

20EN43S

19EN43T

22EN43T 23EN43T

20EN43T

24EN43T

Connection panel (See p.9)

ASSEMBLING AND PREPARING

Setting up the Monitor set

Attaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

Attach the Stand Body to the monitor set.

Attach the Stand Base.

Tighten the screw to the right with a coin.

Stand Body

Detaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

Pull out the Stand Body and Stand Base from the monitor set.

Turn the screw to the left with a coin. Pull out the Stand Base.

Stand Body

ENGLISH

ENG

Stand Base

Stand Body

Stand Base

ASSEMBLING AND PREPARING

ENGLISH

ENG

Mounting on a table

Lift and tilt the Monitor set into its upright

position on a table. Leave a 10 cm (minimum) space from the wall

for proper ventilation.

10 cm

Press (Power) button on the bottom switch

panel to turn the power on.

CAUTION

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

Using the cable holder

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

Cable holder

ASSEMBLING AND PREPARING

WARNING

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.

Do not touch or press the screen when adjusting the angle of the monitor.

Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor set and a table.

http://www.kensington.com

NOTE

ENGLISH

ENG

NOTE

Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.

Front Rear

The Kensington security system is optional. You can obtain it from most electronics stores.

ASSEMBLING AND PREPARING

19EN43S 19EN43T

20EN43S 20EN43T

Model

VESA (A x B) 75 x 75 Standard screw M4 Number of screws 4

22EN43T

23EN43S 23EN43T

24EN43T

22EN43S

100 x 100

ENGLISH

ENG

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

Please, Use the screw and wall mount interface

in accordance with VESA Standards.

If you use screw longer than standard, the

monitor might be damaged internally.

If you use improper screw, the product might be

damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

VESA compatible.

Please use VESA standard as below.

784.8 mm (30.9 inch) and under

y

* Wall Mount Pad Thickness : 2.6 mm * Screw : ĭ 4.0 mm x Pitch 0.7 mm x Length 10 mm

787.4 mm (31.0 inch) and above

y

* Please use VESA standard wall mount pad

and screws.

10 cm

CAUTION

Disconnect the power cord first, and then

y

move or install the Monitor set. Otherwise electric shock may occur. If you install the Monitor set on a ceiling or

y

slanted wall, it may fall and result in severe injury. Use only an authorized LG wall mount

y

and contact the local dealer or qualified personnel. Do not over tighten the screws as this may

y

cause damage to the Monitor set and void your warranty. Use only screws and wall mounts that

y

meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

Use the screws that are listed on the VESA

y

standard screw specifications. The wall mount kit will include an installation

y

manual and necessary parts. The wall mount bracket is optional. You can

y

obtain additional accessories from your local dealer. The length of screws may differ depending

y

on the wall mount. Be sure to use the proper length. For more information, refer to the

y

instructions supplied with the wall mount.

USING THE MONITOR SET

Connecting to a PC

Your Monitor set supports Plug & Play*.

y

*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.

D-SUB connection

Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.

19EN43S

22EN43S

20EN43S

23EN43S

NOTE

When using a D-Sub signal input cable

y

connector for Macintosh

Mac adapter

y

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.

ENGLISH

ENG

DVI-D connection

Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.

19EN43T

23EN43T

20EN43T

24EN43T

22EN43T

19EN43T

20EN43T

23EN43T 24EN43T

22EN43T

USING THE MONITOR SET

ENGLISH

ENG

CAUTION

Connect the signal

y

input cable and tighten it by turning the screws clockwise. Do not press the screen with your finger for

y

a long time as this may result in temporary distortion on the screen. Avoid displaying a fixed image on the

y

screen for a long period of time to prevent image burn. Use a screensaver if possible.

Self Image Setting Function

Press the power button on the bottom panel to turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode)

NOTE NOTE

When you want to use two PC in our Monitor,

y

please connect the signal cable(D-SUB/ DVI-D) respectively in Monitor set. If you turn the Monitor set on while it is cold,

y

the screen may flicker. This is normal. Some red, green, or blue spots may appear

y

on the screen. This is normal.

"Self Image Setting" Function.

y

This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.(Only supported in Analog Mode)

‘AUTO’ Function.

y

When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. (Only supported in Analog Mode)

CUSTOMIZING SETTINGS

MY KEY

AUTO

INPUT

EXIT

FUNC.

CUSTOMIZING SETTINGS

Press the desired button on the bottom of the Monitor set.

Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.

To return to the upper menu or set other menu items, use the up arrow (

Select Exit to leave the OSD menu.

Monitor set Buttons

) button.

ENGLISH

ENG

Button Description

Accesses the main menus.(See p.12)

(Power Button)

OSD Locked/OSD Unlocked

Use this button to enter MY KEY menu.For more information.(See p.17) Use this button to enter Picture Mode, SUPER ENERGY SAVING, DUAL DISPLAY,

DUAL WEB,MY KEY Setting menus.(See p.18) When adjusting your display settings, always press the AUTO button on the MONITOR

SETUP OSD. (Only supported in Analog Mode)

The best display mode 1920 x 1080 Exit

Exit the OSD(On Screen Display). Turns the power on or off.

Power Indicator The power indicator stays red if the display is running properly

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.

(On Mode). If the display is in Sleep Mode, the power indicator blinks red.

+ 25 hidden pages