LG 19LC2D, 22LC2D User Manual

LCD TV

OWNER’S MANUAL

LCD TV MODELS

19LC2D

22LC2D

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer

when you require service.

ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).

As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

www.lgusa.com / www.lg.ca

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE TO CABLE/TV INSTALLER
		CAUTION

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

1

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.

The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:

Heed all warnings. Follow all instructions.

1

5Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided

fit into your outlet, consult an replacement of the obsolete outlet.

2Clean only with dry cloth.

Do not block any ventilation openings. Install in

3accordance with the manufacturer’s instructions.

4Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

6Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

7Only use attachments/accessories specified by the manufacturer.

8Unplug this apparatus when unused for long periods of time.

2

9					cord replaced
						authorized
with the apparatus. When a cart is used, use				servicer. Protect the power cord from physical
caution when moving the cart/apparatus				or mechanical abuse, such as being twisted,
combination to avoid injury from tip-over.				kinked, pinched, closed in a door, or walked
				upon. Pay particular attention to plugs, wall
				outlets, and the point where the cord exits the
				appliance.

10	Never touch this apparatus or antenna during
11	Do not allow a impact shock or any objects to

fall into the product, and do not drop onto the screen with something.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

14 Outdoor use marking :

WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

15	Wet Location Marking : Apparatus shall not be
	exposed to dripping or splashing and no

objects filled with liquids, such as vases, shall be placed on or over apparatus.

13 CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use

16 GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

17 DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The plug must remain readily operable.

3

CONTENTS

WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION

Feature of this TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. . 8
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 9
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	10
Detaching Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	11
Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . .	12
Positioning your display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	13
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	14
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .	14
Kensington Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	15
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . .	16

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Headphone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Channel Search

- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

- Add / Delete Channel (Manual Tuning) . . . . . . 33

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 36

Preset Picture Settings

- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Manual Picture Adjustment

- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 40

- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

XD (Picture Improvement Technology) . . . . . . . . . . . . . 42

Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 43

Back Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Low-Power Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SOUND & LANGUAGE CONTROL

Preset Sound Setting (Sound Mode) . . . . . . . . . . . . . . . . 47

Sound Setting Adjustment - User Mode . . . . . . . . . . . 48

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

On-Screen Menus Language Selection . . . . . . . . . . . . . . 52

Caption Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

- Analog Broadcasting System Captions . . . . . . . 54

- Digital Broadcasting System Captions . . . . . . . . 55

- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

4

TIME SETTING

Clock Setting

- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Sleep Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

PARENTAL CONTROL / RATINGS

Set Password & Lock System

Movie & TV Rating

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

5

INTRODUCTION

FEATURE OF THIS TV

LG's own special digital image generator, consisting of a full digital image processor, six different main picture quality factors.

High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.

Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.

HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

On Disposal

a.The fluorescent lamp used in this product contains a small amount of mercury.

b.Do not dispose of this product with general household waste.

c.Disposal of this product must be carried out in accordance to the regulations of your local authority.

6

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.

User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

For further information, see the the Owner's Manual files supplied CD-ROM.

Owner’s Manual			CD Manual
			(Refer to p.5)

7

5

3

-

ADJUST				TV	POWER
				SAP
MUTE				PICTURE	SOUND	INPUT
			1
			4	2		TIMER
EXIT		7		5	3
		-	8	6
			0	9
	VOL	ADJUST		FAV
MENU		MUTE
	CC		CH
	BACK
		EXIT
ENTER

Remote Control,	Power Cord
Batteries

Option Extras

Cable Management

D-sub 15 pin Cable

PREPARATION

7

PREPARATION

PREPARATION

FRONT PANEL INFORMATION

■ Here shown may be somewhat different from your TV.

POWER	INPUT	MENU	ENTER	VOLUME		CHANNEL
Button	Button	Button	Button	(F,G)Buttons		(E,D)Buttons

/I

INPUT MENU ENTER

VOL

CH

Power/Standby Indicator

Remote Control Sensor Illuminates red in standby mode.

Illuminates green when the set is switched on.

8

BACK PANEL INFORMATION

■ Here shown may be somewhat different from your TV.

8	PREPARATION

		HDMI/DVI IN		ANTENNA/CABLE IN
	2					4
			3
			AV IN	S-VIDEO	RGB (PC) IN	AUDIO IN
		VIDEO	AUDIO
						(RGB/DVI)
1	SERVICE					5
		ONLY
			(MONO)
		RS-232C IN	H/P	VIDEO	AUDIO
		(SERVICE ONLY)		COMPONENT IN
		1	7		6

1

RS-232C IN (SERVICE ONLY) PORT

For service.

2 HDMI/DVI IN

Or DVI (Video) signal to this jack with a HDMI to DVI cable.

3

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

4ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

5(PC) IN

Connect the output from a PC.

AUDIO IN (RGB/DVI)

Connect the audio from a PC or DTV.

COMPONENT IN

Connect a component video/audio device to these jacks.

HEADPHONE INPUT

Plug the headphone into the headphone socket.

8Power Cord Socket

For operation with AC power.

Caution: Never attempt to operate the TV on DC power.

9

PREPARATION

PREPARATION

STAND INSTALLATION

■ Here shown may be somewhat different from your TV.

Carefully place the product screen side down on a cushioned surface that will protect

1product and screen from damage.

Assemble parts of the STAND BODY with COVER BASE of the stand. First,bend

2the HINGE BODY and insert the STAND BODY into a COVER BASE until clicking sound.

3Once assembled take the TV up carefully and face the front side.

STAND BODY

COVER BASE

10

DETACHING STAND

■ Here shown may be somewhat different from your TV.

1	screen side down on a cushioned surface that will protect product
2

COVER BASE

3

STAND BODY

4

PREPARATION

11

PREPARATION

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

■Here shown may be somewhat different from your TV.

1 Connect the cables as necessary.

To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section.

2 Install the CABLE M

shown.

CABLE MANAGEMENT

How to remove

First, press the cable management. Hold the CABLE MANAGEMENT with both hands and pull it upward.

! NOTE

G Do not hold the CABLE MANAGEMENT when moving the product.

- If the product is dropped, you may be injured or the product may be broken.

12

POSITIONING YOUR DISPLAY

■Here shown may be somewhat different from your TV.

■Adjust the position of the panel in various ways for maximum comfort.

•Tilt range

0	0	3
12~1

PREPARATION

13

PREPARATION

PREPARATION

VESA WALL MOUNTING

This product accepts a VESA-compliant mounting interface pad. (optional)

There 4 threaded holes are available for attaching the bracket.

100 mm

100 mm

! NOTE

G Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide.

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4inches on all four sides from the wall.

4 inches

4 inches		4 inches						4		inches

CAUTION G Ensure adequate ventilation by following the clearance recommendations.

14

KENSINGTON SECURITY SYSTEM

-The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.

-For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System.

For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.

NOTE

- The Kensington Security System is an optional accessory.

PREPARATION

15

PREPARATION

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connections.

For optimum picture quality, adjust antenna direction if needed.

Multi-family Dwellings/Apartments Wall (Connect to wall antenna socket)

Antenna

Socket

ANTENNA/CABLE IN

Outdoor	RF Coaxial Wire (75 ohm)
Antenna
(VHF, UHF)	Single-family Dwellings /Houses	Copper Wire
	(Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire when connecting the antenna.

2. Cable

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

ANTENNA/CABLE IN

3. Using both cable and antenna

Antenna

RF Coaxial Wire (75 ohm)

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

UHF

	Antenna	Signal
		Amplifier
		VHF

Diplexer

(Signal	ANTENNA/CABLE IN
Combiner)

ANTENNA/CABLE IN

■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■If the antenna is not installed properly, contact your dealer for assistance.

!NOTE G The TV will let you know when the analog, cable, and digital channel scans are complete.

16

EXTERNAL EQUIPMENT SETUP

■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

When connecting Component cable

1. How to connect		Y	PR	L R
1	Connect the video outputs (Y, PB, PR) of the digital set
	top box to the COMPONENT IN VIDEO jacks on
	the set. Match the jack colors
	(Y = green, PB = blue, and PR = red).
			1	2
	box to
		AV	S-		AUDIO IN
		IDEO AUDIO		IN
					(RGB/DVI)
2. How to use		(MONO)
■ Turn on the digital set-top box.
	(Refer to the owner’s manual for the digital set-top box. operation)	H/P
			VIDEO	AUDIO

COMPONENT IN

■Select Component input source by using the INPUT button on the remote control.

					Y, CB/PB, CR/PR
	Signal	Component	HDMI
					Resolution		Horizontal	Vertical
							Frequency(KHz)	Frequency(Hz)
	480i	Yes	No
	480p	Yes	Yes				15.73	59.94
					720x480i
							15.73	60.00
	720p	Yes	Yes
	1080i	Yes	Yes		720x480p		31.47	59.94
							31.50	60.00
	1080p	Yes	Yes
					1280x720p		44.96	59.94
							45.00	60.00
					1920x1080i		33.72	59.94
							33.75	60.00
							27.00	24.00
					1920x1080p		33.75	30.00
							67.43	59.94
							67.50	60.00

SETUP EQUIPMENT EXTERNAL

17

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

When connecting HDMI cable

1.How to connect

1 Connect the digital set-top box to HDMI/DVI IN jack on the set.

	connection is necessary.		ANTEN
		HDMI/DVI IN
	audio and video.
2.	to use	VIDEO	AV IN
			AUDIO
			S-VIDEO
		SERVICE
	on the digital set-top box.	ONLY
			(MONO)
	to the owner’s manual for the digital set-top box.)
		1
	HDMI input source by using the INPUT button	H/P
	the remote control.	RS-232C IN	VIDEO
		(SERVICE ONLY)
			CO
!	NOTE
G When connected, the TV will tell a connected device what
	resolution it supports and the resolution it prefers. If the
	device supports this Auto HDMI function, the player output	HDMI-DTV OUTPUT
	resolution will be automatically set to 720p.

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

	HDMI/DVI-DTV mode
	Resolution	Horizontal	Vertical
		Frequency(KHz) Frequency(Hz)
	720x480p	31.469	59.94
		31.500	60.00
	1280x720p	44.96	59.94

45.0060.00

1920x1080i	33.72	59.94

33.7560.00

27.0024.00

1920x1080p	33.75	30.00

67.4359.94

67.5060.00

18

When connecting HDMI to DVI cable

HDMI/DVI IN			ANTENNA/CABLE IN
		AV IN	S-VIDEO			AUDIO IN
	VIDEO	AUDIO		RGB (PC) IN
						(RGB/DVI)
SERVICE
ONLY
		(MONO)
	1
	H/P
RS	IN		VIDEO		AUDIO
	ONLY)
			COMPONENT IN
					2

DVI-	OUTPUT			L		R

1. How to connect

1 Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the set.

the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the set.

2.How to use

■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

■Select HDMI input source by using the INPUT button on the remote control.

SETUP EQUIPMENT EXTERNAL

19

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

DVD SETUP

When connecting Component cable

1. How to connect

1	Connect the video outputs (Y, PB, PR) of the DVD to the
	COMPONENT IN VIDEO jacks on the set.	PR L R
	Y
	Match the jack colors
	(Y = green, PB = blue, and PR = red).

2. How to use

on the DVD player, insert a DVD.

Component input source by using the INPUT on the remote control.

to the DVD player's manual for operating instructions.

12

	AV
VIDEO	S-	IN	AUDIO IN
	AUDIO		(RGB/DVI)

(MONO)

H/P

VIDEO AUDIO

COMPONENT IN

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV	Y	PB	PR
	Y	PB	PR
Video output ports	Y	B-Y	R-Y
on DVD player	Y	Cb	Cr
	Y	Pb	Pr

20

When connecting with an S-Video cable

1. How to connect

Connect the S-VIDEO output of the DVD to the

1S -VIDEO input on the set.

2.How to use

on the DVD player, insert a DVD.

DVI IN	ANTENNA/CABLE IN
AV IN
S	RGB (PC) IN	AU
VIDEO AUDIO		(RG

H/P

	32C IN	VIDEO	AUDIO
	CE ONLY)
		COMPONENT IN

2

AV input source by using the INPUT button on the control.

to the DVD player's manual for operating instructions.

R S-VIDEO

AUDIO

When connecting HDMI cable

1.How to connect

1 Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the set.

			HDMI/DVI IN		ANTE
		HDMI supports both audio and video.
					AV IN
	2. How to use		SERVICE		S-VIDEO
				VIDEO	AUDIO
			ONLY
		HDMI input source by using the INPUT button			(MONO)
		the remote control.
		to the DVD player's manual for operating instructions.	1	H/P
			RS-232C IN		VIDE
			(SERVICE ONLY)		C
	!	NOTE
	G When connected, the TV will tell a connected device what
		resolution it supports and the resolution it prefers. If the
		device supports this Auto HDMI function, the player out-	HDMI-DVD OUTPUT
		put resolution will be automatically set to 720p.

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the DVD to 720p.

SETUP EQUIPMENT EXTERNAL

21

EXTERNAL EQUIPMENT SETUP

VCR SETUP

SETUP EQUIPMENT EXTERNAL

■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty

does not cover the product bearing this phenomenon.

When connecting with an antenna

HDMI/DVI IN	ANTENNA/CABLE IN
	AV IN
	S-VIDEO	(PC) IN	AUDIO IN
	VIDEO AUDIO		(RGB/DVI)
SERVICE
			1
ONLY
	(MONO)		OUT	VIDEO L	R S-VIDEO
			IN		OUTPUT
					SWITCH
RS-232C IN	H/P
	VIDEO	AUDIO
(SERVICE ONLY)
	COMPONENT IN			Wall Jack

2

Antenna

1. How to connect

1 Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the set.

the antenna cable to the RF antenna in socket of the VCR.

2.How to use

■Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

■Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

22