LG 22LB490B-ZG, 22LB490U-ZG, 22LB491U-ZB, 22LB498U-ZG, 22LB4900-ZA Owners Manual
...
OWNER’S MANUAL
*
LED TV
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain
it for future reference.
LB49**
LB57**
LB58**
*MFL68027048*
P/NO : MFL68027048(1402-REV00)
Printed in Korea
www.lg.com
2
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
ENGLISH
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com
SAFETY INSTRUCTIONS
3
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/or remote control in the following environments:
y
- A location exposed to direct sunlight
- An area with high humidity such as a bathroom
- Near any heat source such as stoves and other devices that produce
heat
- Near kitchen counters or humidifiers where they can easily be exposed
to steam or oil
- An area exposed to rain or wind
- Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
Do not place the product where it might be exposed to dust.
y
This may cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains electric
y
supply.This plug must remain readily attached and operable when TV is in
use.
Do not touch the power plug with wet hands. Additionally, if the cord pin is
y
wet or covered with dust, dry the power plug completely or wipe dust off.
You may be electrocuted due to excess moisture.
ENGLISH
Make sure to connect Mains cable to compliant AC mains socket with
y
Grounded earth pin. (Except for devices which are not grounded on earth.)
Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not secured
y
completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects such as
y
a heater.
This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
y
Otherwise, this may result in fire or electric shock.
4
Desiccant
SAFETY INSTRUCTIONS
ENGLISH
Bend antenna cable between inside and outside building to prevent rain
y
from flowing in.
This may cause water damaged inside the Product and could give an
electric shock.
When mounting TV onto wall make sure to neatly install and isolate cabling
y
from rear of TV as to not create possibility of electric shock /fire hazard.
Do not plug too many electrical devices into a single multiple electrical
y
outlet.
Otherwise, this may result in fire due to over-heating.
Do not drop the product or let it fall over when connecting external devices.
y
Otherwise, this may result in injury or damage to the product.
Keep the anti-moisture packing material or vinyl packing out of the reach of
y
children.
Anti-moisture material is harmful if swallowed. If swallowed by mistake,
force the patient to vomit and visit the nearest hospital. Additionally, vinyl
packing can cause suffocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the TV.
y
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
y
consume them.
Please seek Doctor- Medical Attention immediately if child consumes
batteries.
Do not insert any metal objects/conductors (like a metal chopstick/cutlery/
y
screwdriver) between power cable plug and input Wall Socket while it is
connected to the input terminal on the wall. Additionally, do not touch the
power cable right after plugging into the wall input terminal. You may be
electrocuted.
(Depending on model)
Do not put or store inflammable substances near the product.
y
There is a danger of combustion/explosion or fire due to careless handling
of the inflammable substances.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into
y
the product, or inflammable objects such as paper and matches. Children
must pay particular attention.
Electrical shock, fire or injury can occur. If a foreign object is dropped into
the product, unplug the power cord and contact the service centre.
Do not spray water on the product or scrub with an inflammable substance
y
(thinner or benzene). Fire or electric shock accident can occur.
SAFETY INSTRUCTIONS
5
Do not allow any impact, shock or any objects to fall into the unit, and do
y
not drop anything onto the screen.
You may be injured or the product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
y
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the windows
y
and ventilate.
It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own discretion.
y
Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and contact
y
your local service centre.
- The product has been impacted by shock
- The product has been damaged
- Foreign objects have entered the product
- The product produced smoke or a strange smell
This may result in fire or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the TV
y
for a long period of time.
Accumulated dust can cause fire hazard and insulation deterioration can
cause electric leakage/shock/fire.
Apparatus shall not be exposed to dripping or splashing and no objects
y
filled with liquids, such as vases, shall be placed on the apparatus.
ENGLISH
Do not install this product on a wall if it could be exposed to oil or oil mist.
y
This may damage the product and cause it to fall.
CAUTION
Install the product where no radio wave occurs.
y
There should be enough distance between an outside antenna and power
y
lines to keep the former from touching the latter even when the antenna
falls.
This may cause an electric shock.
6
SAFETY INSTRUCTIONS
ENGLISH
Do not install the product on places such as unstable shelves or inclined
y
surfaces. Also avoid places where there is vibration or where the product
cannot be fully supported.
Otherwise, the product may fall or flip over, which may cause injury or
damage to the product.
If you install the TV on a stand, you need to take actions to prevent the
y
product from overturning. Otherwise, the product may fall over, which may
cause injury.
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional
y
parts) to the back of the product. When you install the set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
y
When installing the antenna, consult with a qualified service technician. If
y
not installed by a qualified technician, this may create a fire hazard or an
electric shock hazard.
We recommend that you maintain a distance of at least 2 to 7 times the
y
diagonal screen size when watching TV.
If you watch TV for a long period of time, this may cause blurred vision.
Only use the specified type of battery.
y
This could cause damage to the remote control.
Do not mix new batteries with old batteries.
y
This may cause the batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep away from direct Sunlight ,
y
open fireplace and electric heaters .
Do not place non-rechargeable batteries in charging device.
y
Make sure there are no objects between the remote control and its sensor.
y
Signal from Remote Control can be interrupted due to external/internal
y
lighting eg Sunlight, fluorescent lighting.
If this occurs turn off lighting or darken viewing area.
When connecting external devices such as video game consoles, make
y
sure the connecting cables are long enough.
Otherwise, the product may fall over, which may cause injury or damage
the product.
Do not turn the product On/Off by plugging-in or unplugging the power plug
y
to the wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
SAFETY INSTRUCTIONS
7
Please follow the installation instructions below to prevent the product from
y
overheating.
- The distance between the product and the wall should be more than
10 cm.
- Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
- Do not install the product on a carpet or cushion.
- Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Take care not to touch the ventilation openings when watching the TV for
y
long periods as the ventilation openings may become hot. This does not
affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance indicates damage or
y
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet.
y
This may cause a fire hazard.
Protect the power cord from physical or mechanical abuse, such as being
y
twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a hand or sharp object such
y
as nail, pencil or pen, or make a scratch on it, as it may cause damage to
screen.
Avoid touching the screen or holding your finger(s) against it for long
y
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
ENGLISH
When cleaning the product and its components, unplug the power first and
y
wipe it with a soft cloth. Applying excessive force may cause scratches or
discolouration. Do not spray with water or wipe with a wet cloth. Never use
glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol
etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
y
source even if you turn off this unit by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at the
y
plug.
Don’t pull at the cord to unplug the power cord from the power board, as
this could be hazardous.
When moving the product, make sure you turn the power off first. Then,
y
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire hazard
or cause electric shock.
8
SAFETY INSTRUCTIONS
ENGLISH
When moving or unpacking the product, work in pairs because the product
y
is heavy.
Otherwise, this may result in injury.
Contact the service centre once a year to clean the internal parts of the
y
product.
Accumulated dust can cause mechanical failure.
Refer all servicing to qualified service personnel. Servicing is required when
y
the apparatus has been damaged in any way, such as power supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “flicker” when it
y
is turned on. This is normal, there is nothing wrong with product.
The panel is a high technology display product with resolution of two million
y
to six million pixels. You may see tiny black dots and/or brightly coloured
dots (red, blue or green) at a size of 1 ppm on the panel. This does not
indicate a malfunction and does not affect the performance and reliability of
the product.
This phenomenon also occurs in third-party products and is not subject to
exchange or refund.
You may find different brightness and color of the panel depending on your
y
viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video
y
game) for a prolonged time may cause damage to the screen, resulting in retention of the image,
which is known as image sticking. The warranty does not cover the product for image sticking.
Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours
for LCD, 1 or more hours for Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders
of the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
Generated Sound
y
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by
plastic thermal contraction due to tempera-ture and humidity. This noise is common for products
where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise
is generated from a high-speed switching circuit, which supplies a large amount of current to
operate a product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
ASSEMBLING AND PREPARING
<
<
9
NOTE
yImage shown may differ from your TV.
yYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yThe available menus and options may differ from the input source or product model that you are
using.
yNew features may be added to this TV in the future.
yThe TV can be placed in standby mode in order to reduce the power consumption. And the TV
should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yThe energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yDo not use any unapproved items to ensure the safety and product life span.
yAny damage or injuries caused by using unapproved items are not covered by the warranty.
ySome models have a thin film attached on to the screen and this must not be removed.
NOTE
yThe items supplied with your product may vary depending on the model.
yProduct specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
yFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
ENGLISH
B
A
B
*A
10 mm
=
*B
18 mm
A
=
ENGLISH
10
ASSEMBLING AND PREPARING
AV MODE
INPUT
ENERGY
TV
SAVING
1 2 3
4 5 6
7 809
FLASHBK
LIST
MARK
FAV
P
A
G
3D
CHVOL
E
MUTE
INFO
MENU
Q.MENU
ENTER
EXIT
BACK
L/R SELECT
FREEZE
RATIO
Remote Control, Batteries
(AAA)
Cable Managements
2EA
(Only LB57**, LB58**-ZA/ZB/
ZG/ZJ)
Stand Base
(Only LB57**, LB58**-ZA/ZB/
ZG/ZJ)
Owner’s Manual Cable Holder
Stand Base
(Only LB49**-ZH)
Stand Base
(Only LB49**-ZB/ZG)
Stand Base/Stand Body
(Only LB58**-ZM)
Power Cord
(Only LB57**, LB58**)
AC-DC Adapter / Power
Cord
(Only LB49**)
Stand Screws
2 EA, M4 x L10
(Only 28LB49**-ZH)
ASSEMBLING AND PREPARING
Stand Screws
4EA, M4 x L14
(Only 39/42/47/50LB57**,
39/42/47/50/55LB58**ZA/ZB/ZG/ZJ,
42/47/50/55/60LB58**-ZM)
11
ENGLISH
Stand Screws
2EA, M4 x L20
(Only 32/39LB58**-ZM)
4EA, M4 x L20
(Only 32LB57**,
32LB58**-ZA/ZB/ZG/ZJ)
Rubber
2EA
(Only LB58**-ZM)
Stand Screws
4EA, M4 x L20
(Only LB58**-ZM)
Wall Mount Spacers
2EA
(Only 42LB57**, 42LB58**)
12
ASSEMBLING AND PREPARING
ENGLISH
Separate purchase
Separate purchase items can be changed or modied for quality improvement without any notication.
Contact your dealer to buy these items.
These devices only work with certain models.
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
AN-MR500
Magic Remote
LG Audio Device Tag On
* You can use the Magic Remote and LG Audio Device(Wireless) only when you are using the Wi-Fi/
Bluetooth Dongle.
AN-WF500
Wi-Fi/Bluetooth Dongle
AN-VC5**
Video Call Camera
Loading...