Contents
Installation..........................................................2
Connection of external equipment..................2
Location and function of controls...................3
Basic operation.................................................5
On screen menus..............................................5
Setting up TV stations......................................6
Picture adjustment............................................7
Sound adjustment.............................................8
Time setting.......................................................9
Other functions.................................................9
PIP operation (option).....................................10
Teletext (option)...............................................10
Troubleshooting check list
2
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and mains plugs.
DISCONNECTING DEVICE FROM MAINS
- Mains plug is the disconnecting device. The plug
must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the
set to rain or moisture.
Do not place anything containing liquid on top of
the set, this may cause a fire or could give an
electric shock.
Service
Never remove the back cover of the set as this
can expose you to very high voltage and other
hazards. If the set does not operate properly,
unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.
Location
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.
Note:
To remove dirt or fingerprint on the surface of your
TV, please rub with a line-free cloth supplied in
the accessory.Do not pose too much pressure in
cleaning so as to prevent any risk of damage to
the product.
Aerial socket
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on the programme
number 0 using the ‘Manual programme tuning’ section.
4.
Select the programme number where the
VCR channel is stored.
5.
Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the
VCR to audio/video in sockets of the set.
2. If the VCR is connected to the AV sockets on
the set, press the TV/AV button to select
AV
(or AV 1 ), or
AV 2.
3. Press the PLAY button on the VCR.
You can also record programmes received by
the TV on video tape via audio/video out
sockets.
Euro scart socket (option)
1. Connect the Euro scart socket of the VCR to
the Euro scart socket of the set.
2. Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when
connected to Euro scart socket, the set will
switch to
AV (or AV 1 )
mode automatically. But
if you want to keep on watching TV mode,
press the
DD / EE
or NUMBER buttons.
Otherwise press the TV/AV button on the
remote control handset to select
AV (or AV 1 )
.
You can also record programmes received by
the TV on video tape.
Component in sockets (option)
1. Connect the COMPONENT video output
sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
DVD player to the COMPONENT INPUT sockets (Y PB PR) on the set.
2. Connect the audio cable from the DVD player
to AUDIO IN sockets of
AV (or AV1 )
.
3. Press the TV/AV button to select COMPO-
NENT.
4. Press the PLAY button on the DVD player.
The COMPONENT playback picture appears
on the screen.
S-video / Audio in sockets (S-AV) (option)
When connecting the S-video socket of the VCR
to the S-VIDEO socket of the set, the picture quality will be further improved.
1. Connect the S-video socket of the VCR to the
S-VIDEO socket of the set.
2. Connect the audio cable from the VCR to the
AUDIO sockets of the set.
3. Select AV 2 by pressing the TV/AV button
repeatedly.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
Note : If both S-VIDEO and VIDEO sockets have
been connected to the VCR simultaneously, only
the S-VIDEO can be received.
Headphone socket (option)
You can listen to the sound through the headphones. To adjust the headphone volume, press
the F / G button.
If you press the MUTE button, the sound from the
headphone’s is switched off.
Connection of external equipment