LG 21CD1RGE User Manual

Colour Television

OWNER’S MANUAL

Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this infor­mation to your dealer when you require service.

Model number :
Serial number :

P/NO : MFL39582022-EN (MC059B)

2

Power

This set operates on an AC mains supply, the volt­age is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and mains plugs.
Press the POWER button on the front panel or side
panel to turn off the TV when the TV set is not being
used for a long time.It is recommended to remove the
plug from the wall outlet(Power point).

Disconnecting device from mains

Mains plug is the disconnecting device. The plug
must remain readily operable

Warning

To prevent fire or shock hazard, do not expose the set
to rain or moisture.
Do not place anything containing liquid on top of the set,
this may cause a fire or could give an electric shock.

Service

Never remove the back cover of the set as this can
expose you to very high voltage and other hazards. If
the set does not operate properly, unplug it and call
your dealer.

Aerial

Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.

Location

Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.

Installation

Connection of external equipment

Aerial socket

1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.

2. Connect the aerial cable to the RF aerial in
socket of the VCR.

3. Store the VCR channel on a desired pro­gramme number using the ‘Manual pro­gramme tuning’ section.

4. Select the programme number where the
VCR channel is stored.

5. Press the PLAY button on the VCR.

Audio/Video in/out sockets (option)

1. Connect the audio/video out sockets of the VCR
to audio/video in sockets of the set and in sock­ets of the VCR to RF OUT sockets of the set.

2. If the VCR is connected to the AV sockets on the
set, press the TV/AV button to select AV 1 or AV 2 .

3. Press the PLAY button on the VCR.The VCR
playback picture appears on the screen.
You can also record programmes received by the
TV on video tape via audio/video out sockets.

Note : If you have a mono VCR, connect the
audio cable from the VCR to the AUDIO L/MONO
socket of the set.

Euro scart socket (option)

1. Connect the Euro scart socket of the VCR to
the Euro scart socket of the set.

2. Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when
connected to Euro scart socket, the set will
switch to

AV 1 mode automatically. But if you

want to keep on watching TV mode, press the

DD / EE

or NUMBER buttons.Otherwise press

the TV/AV button on the remote control
handset to select AV 1 The VCR playback pic­ture appears on the screen.

You can also record programmes received by the

TV on video tape.

Note : Signal type RGB, i.e. the signals red, green
and blue can only be selected for the Euro scart
socket. These signals are transmitted, for exam­ple, by a pay TV decoder, game machine or photo
CD unit, etc.

Component in sockets (option)

1. Connect the COMPONENT video output
sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
COMPONENT (480i) to the COMPONENT
INPUT sockets (Y PB PR) on the set.

2. Connect the audio cable from the COMPO­NENT to AUDIO IN sockets of AV IN2.

3. Press the TV/AV button to select COMPONENT.

4. Press the PLAY button on the COMPONENT.
The COMPONENT playback picture appears
on the screen.

Headphone socket (option)

You can listen to the sound through the head­phones. To adjust the headphone volume, press
the F / G button.
If you press the MUTE button, the sound from the
headphone’s is switched off.

Location and function of controls

Battery installation

The remote control handset is powered by AAA
type batteries.Install batteries as indicated by the
polarity symbols ( and ) marked inside the
compartment.

Note : To avoid damage from possible battery
leakage, remove the batteries if you do not plan to
use the remote control handset for an extended
period of time

+

-

or

3

Remote control handset

Before you use the remote control handset,
please install the batteries. See the next page.

1. POWER

switches the set on from standby or off to standby.

2. NUMBER BUTTONS

switches the set on from standby or directly
select a number.

3. MENU

selects a menu.

4. EYE/*(option)

switches the eye function on or off.

5.

/

(Programme Up/Down)

selects a programme or a menu item.
switches the set on from standby.
scans programmes automatically.

FF / GG

(Volume Up/Down)

adjusts the volume.
adjusts menu settings.

OK

accepts your selection or displays the current
mode.

6. Q.VIEW

returns to the previously viewed programme.

7. PSM (Picture Status Memory)

recalls your preferred picture setting.

8. FAVOURITE

selects a favorite programme.

9. TURBO PICTURE / SOUND BUTTON
(option)

selects Turbo picture and sound.

10. MUTE

switches the sound on or off.

11. TV/AV

selects TV or AV mode.
switches the set on from standby.

12. I/II/

*

(option)

selects the language during dual language

broadcast. (option)
selects the sound output.

13. LIST

displays the programme table.

14. SLEEP

sets the sleep timer.

15. SSM/

*

(Sound Status Memory) (option)

recalls your preferred sound setting.

16. SURROUND (ºº/*) (option)

selects surround sound.

*

: No function

COLOURED BUTTONS : These buttons are

used for teletext (only TELETEXT models) or pro­gramme edit.

Front panel

- MAIN POWER (ON/OFF)

switches the set on or off.

- POWER/STANDBY INDICATOR

illuminates brightly when the set is in stand­by mode.
dims when the set is switched on.

- REMOTE CONTROL SENSOR

Note : Only use the supplied remote control
handset. (When you use others, they’ll be
not able to function.)

- MENU (option)

selects a menu.

- OK (option)

accepts your selection or displays the current
mode.

FF / GG

(Volume Up/Down)

(option)

adjusts the volume.
adjusts menu settings.

DD / EE

(Programme Up/Down) (option)

selects a programme or a menu item.
switches the set on from standby.

- AUDIO (or AUDIO-L/R)/VIDEO IN SOCK­ETS (AV or AV2) (option)

Connect the audio/video out sockets of exter­nal equipment to these sockets.

- HEADPHONE SOCKET (option)

Connect the headphone plug to this socket.

- EYE (option)

adjusts picture according to the surrounding
conditions.

- TURBO SOUND / PICTURE (option)

switches Turbo sound or Turbo picture function
on or off.

- TV/AV (option)

selects TV or AV mode.
clears the menu from the screen.
switches the set on from standby.

- (Function) (option)

selects volume, EYE (option), picture items or
brief auto programme while the menus not
display.

- + / - (

DD / EE

) (option)

adjusts the function or selects a programme.
switches the set on from standby.

Note : Shown is a simplified representation of
front or side panel. Here shown may be some­what different from your set.

Location and function of controls

5

1

4

2

6

8

5

7

12

13

11

10

9

3

14
15

16

( )

( )