Page 1
Please read this manual carefully before operating
your set and retain it for future reference.
The model and serial number of the TV is located
on the back and one side of the TV.
Record it below should you ever need service.
Model:
Serial:
LCD TV
OWNER’S MANUAL
19 L D 350
22LD350
26LD350
32LD350
32LD320
32LD450
37L D450
42LD450
47L D450
42LD420
47L D420
42LD520
47L D520
55LD 520
P/NO : SAC34134201 (0910-REV00)
www.lgusa.com / www.lg.ca / www.lgcommercial.com
This product qualifies for ENERGY STAR in the “factory
default (Home Use)” setting.
Changing the factory default settings or enabling other features may increase power consumption that could exceed the
limits necessary to quality for ENERGY STAR.
1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User
1-888-542-2623 CANADA
LG Customer Information Center
Page 2
2
WARNING / CAUTION
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause (harmful) interference,
and (2) this device must accept any interference
received, including interference that may cause undesired operation (of the device).
Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
Page 3
3
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lighting storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
1
2
3
4
5
7
8
6
9
10
Page 4
4
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during
a thunder or lighting storm.
When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.
Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
CAUTION concerning the Power Cord:
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.
Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.
WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.
Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).
GGRROOUU NNDD IINNGG
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC outlet). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.
DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The
plug must remain readily operable.
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.
12
11
14
13
16
17
18
19
Powe r
Supply
Short-circuit
Breaker
15
Page 5
5
AANNTTEENNNN AASS
OOuu ttddoooo rr aanntt ee nnnnaa ggrr oouu nndd iinngg
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.
Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding
electrode.
AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700
CC lleeaanniinngg
When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.
MMoo vviinngg
Make sure the product is turned off,
unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.
VV ee nnttiill aattiioonn
Install your TV where there is proper ventilation. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.
Take care not to touch the ventilation openings. When watching the TV for a long period,
the ventilation openings may become hot.
If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the power
cord contact an authorized service center.
Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.
Keep the product away from direct sunlight.
FFoo rr LL CCDD TTVV
If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
20
23
25
24
26
27
28
21
22
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC: National Electrical Code
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.
Page 6
6
CONTENTS
WARNING / CAUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
FEATURE OF THIS TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATION
Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stand Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cable Management
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
Swivel Stand
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Positioning your Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
Desktop Pedestal Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . .
26
Attaching the TV to a Desk
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Kensington Security System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Securing the TV to the wall to prevent falling when
the TV is used on a stand
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 29
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DVD Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
VCR Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Other A/V Source Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
USB Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Audio out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
Headphone Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
PC Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
WATCHING TV / CHANNEL CONTROL
Remote Control Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Turning On TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
Channel Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
Initial Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
On-Screen Menus Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Quick Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
Channel Setup
- Auto Scan (Auto Tuning)
. . . . . . . . . . . . . . . . . . . . . . . . . . . 53
- Add / Delete Channel (Manual Tuning)
. . . . . .
55
- Channel Editing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
Favorite Channel Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Favorite Channel List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Brief Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Input List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
AV Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Simple Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
Key Lock
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
SIMPLINK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
USB
Entry Modes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Photo List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
Music List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
PICTURE CONTROL
Picture Size (Aspect Ratio) Control
. . . . . . . . . . . . . . . . . .
74
Picture Wizard
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Preset Picture Settings (Picture Mode)
. . . . . . . . . . . . .
78
Manual Picture Adjustment - User Mode
. . . . . . . . . . 79
Picture Improvement Technology
. . . . . . . . . . . . . . . . . . . . . 80
Expert Picture Control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
Energy Saving
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
84
Picture Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Power Indicator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
86
Demo Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
Page 7
7
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 88
Clear Voice II
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Preset Sound Setting (Sound Mode)
. . . . . . . . . . . . . . . . 90
Sound Setting Adjustment - User Mode
. . . . . . . . . . . 91
Balance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
TV Speakers On/Off Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
Audio Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Stereo/SAP Broadcasts Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . 95
Audio Language
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
On-Screen Menus Language Selection
. . . . . . . . . . . . . . 97
Caption Mode
- Analog Broadcasting System Captions
. . . . . . .
98
- Digital Broadcasting System Captions
. . . . . . . .
99
- Caption Option
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0
TIME SETTING
Clock Setting
- Auto Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
101
- Manual Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 3
Sleep Timer Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 4
PARENTAL CONTROL / RATINGS
Set Password & Lock System
. . . . . . . . . . . . . . . . . . . . . . . . . .
10 5
Channel Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8
Movie & TV Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9
Downloadable Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
114
External Input Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
APPENDIX
Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
Maintenance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
119
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
External Control Through RS-232C
. . . . . . . . . . . . . . . . .
12 2
Open Source License
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 6
Page 8
8
FEATURE OF THIS TV
The AV Mode optimizes the picture into Cinema,
Sports, and game Mode according to the video and
audio content. The viewer has the ability to quickly
choose the correct mode for the picture they are
viewing.
Automatically enhances and amplifies the sound of
human voice frequency range to help keep dialogue
audible when background noise swells.
LG TV include a unique invisible speaker system,
tuned by renowned audio expert, Mr. Mark Levinson.
Speakers are embedded in strategic spots behind the
front cabinet and use minute vibrations to turn the
entire front bezel into the speaker system. The result
is a clean, polished look, and enhanced audio by
increasing the “sweet spot”, giving a wider and richer
sound field.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
Manufactured under license from Dolby Laboratories.
“
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
This TV contains the detailed calibrations necessary
for professional certification by the Imaging Science
Foundation. The resulting ISF “day” and “night” modes
will then be accessible by the user to experience the
best their LG HDTV has to offer.
CALIBRATE LIKE A PRO: Sophisticated and detailed
calibrations can be made through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an
ISF certified technician.
High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.
■
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
■
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
■
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio
setting for an extended period.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN
Page 9
PREPARATION
9
ACCESSORIES
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
1.5V 1.5V
Owner’s Manual Power Cord
Remote Control,
Batteries
E
N
E
R
G
Y
C
H
V
O
L
123
45
0
6
789
P
A
G
E
S
A
V
I
N
G
TV
A
V
M
O
D
E
I
N
P
U
T
F
A
V
R
A
T
I
O
M
U
T
E
B
A
C
K
E
X
IT
E
N
T
E
R
M
A
R
K
L
I
S
T
F
L
A
S
H
B
K
M
E
N
U
I
N
F
O
Q
.
M
E
N
U
CD Manual
FFoorr 1199//2222LLDD335500
Cable Holder
(Refer to P.23)
OOnnllyy 2266//3322LLDD335500
(M4x20)
Bolts for stand assembly
(Refer to P.18)
Screw for stand fixing
(Refer to P.27)
Protection Cover
(Refer to P.19)
Protection Cover
(Refer to P.17)
x 8
OOnnllyy 3322//3377//4422//4477LLDD445500
(M4x20)
Bolts for stand assembly
(Refer to P.20)
Screw for stand fixing
(Refer to P.27)
Protection Cover
(Refer to P21)
x 4
OOppttiioonn EExxttrraass
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
stain. Excessive pressure may cause
scratch or discoloration.
Polishing Cloth
Not included with all models
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.
Page 10
PREPARATION
10
FRONT PANEL INFORMATION
PREPARATION
■
Image shown may differ from your TV.
CHANNEL ( , )
Buttons
VOLUME
(-, +) Buttons
ENTER Button
19/22LD350
MENU Button
POWER Button
INPUT Button
SPEAKER
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
Remote Control Sensor
CHANNEL ( , )
Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
26/32LD350
INPUT
MENU
ENTER
VOL
CH
CH
VOL
ENTER
MENU
INPUT
Page 11
PREPARATION
11
■
Image shown may differ from your TV.
SPEAKER
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
CHANNEL ( , )
Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
32/37/42/47LD450
Remote Control Sensor
CH
VOL
ENTER
MENU
INPUT
Page 12
PREPARATION
12
BACK PANEL INFORMATION
PREPARATION
K
AC-IN
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA/
CABLE IN
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
/DVI IN
AV IN
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
1 4
19/22LD350
7 6
■
Image shown may differ from your TV.
USB IN
SERVICE ONLY
H/P
2 3 5
IN 2
VIDEO
AUDIO
L(MONO)
R
H/P
USB IN
SERVICE ONLY
AV IN 2
1
8
9
5
9
8
11
1
/DVI IN
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
AV IN 1
1 4
26LD350
7 6
2 3 5
Page 13
PREPARATION
13
■
Image shown may differ from your TV.
AC IN
1
10
9
5
1
/DVI IN
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
AV IN 1
1 4
32LD350
7 6
2 3 5
11
IN 2
H/P USB IN
R
AUDIO
L(MONO)
VIDEO
AV IN 2
Page 14
PREPARATION
14
PREPARATION
■
Image shown may differ from your TV.
1
10
9
5
1
/DVI IN
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
RGB IN (PC)
VIDEO
YPB PR
L R
AUDIO
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
AV IN 1
VIDEO
AUDIO
L(MONO)
R
1 4
32/37/42/47LD450
7 6
3 5
11
2
IN 2
H/P USB IN
R
AUDIO
L(MONO)
VIDEO
AV IN 2
Page 15
PREPARATION
15
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO IN (RGB/DVI)
1/8" (0.32 cm) headphone jack for analog PC
audio input.
OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps and
home theater systems.
Note: In standby mode, this port doesn’t work.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
This port is used for Service or Hotel mode.
AV (Audio/Video) IN
Analog composite connection. Supports standard
definition video only (480i).
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red
and white for audio.
USB IN SERVICE ONLY
Used for software updates.
HEADPHONE INPUT
Plug the headphone into the headphone socket.
USB INPUT
Used for viewing photos and listening to MP3s.
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
1
2
3
4
5
9
8
7
6
10
11
Page 16
PREPARATION
16
STAND INSTRUCTIONS (For 19/22LD350)
PREPARATION
■
Image shown may differ from your TV.
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the TV as shown until you hear it click.
1
2
INSTALLATION
Page 17
PREPARATION
17
PROTECTION COVER
Insert the
PPRROOTTEECCTT IIOONN CCOOVVEERR
into the TV.
4
PPRROOTTEECCTT IIOONN CCOO VVEERR
Fix the 4 bolts securely using the holes in the
back of the TV.
5
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
Page 18
PREPARATION
18
STAND INSTRUCTIONS (For 26/32LD350)
PREPARATION
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the parts of the
SSTTAA NN DD BBOODD YY
with
CCOO VVEERR BBAA SSEE
of the TV by using the 4
screws supplied.
Fix the 4 bolts securely using the holes in the
back of the TV.
1
2
Assemble the TV as shown.
2
3
INSTALLATION
GG
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
NOTE
!
■
Image shown may differ from your TV.
CCOO VVEERR BBAA SSEE
SSTTAANNDD BBOODD YY
Page 19
PREPARATION
19
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
After removing the stand, install the included
pprroottee cctt iioo nn cc oovvee rr
over the hole for the stand.
Press the
PPRROOTT EECCTTII OONN CC OO VVEERR
into the TV
until you hear it click.
PROTECTION COVER
Page 20
PREPARATION
20
STAND INSTRUCTIONS (For 32/37/42/47LD450)
PREPARATION
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV.
1
2
3
INSTALLATION
GG
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
NOTE
!
Page 21
PREPARATION
21
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
PROTECTION COVER
After removing the stand, install the included
pprroottee cctt iioo nn cc oo vvee rr
over the hole for the
stand.
Press the
PPRROOTT EECCTTII OONN CCOOVVEERR
into the TV
until you hear it click.
4
Page 22
PREPARATION
22
VESA WALL MOUNTING
PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
GG
Do not install your wall mount kit while your TV is turned on. It may result in personal
injury due to electric shock.
CAUTION
GG
Screw length needed depends on the wall mount
used. For further information, refer to the instructions included with the mount.
GG
Standard dimensions for wall mount kits are shown
in the table.
GG
When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
GG
Do not use screws longer then the standard dimension, as they may cause damage to the inside to
the TV.
GG
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the
screws may differ depending on their specifications.
GG
Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.
GG
LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installation instructions.
NOTE
!
Model
VESA (A *B)
Standard Screw Quantity
Wall Mounting Bracket
(sold separately)
19LD350,
22LD350
37LD450,
42LD450,
47LD450
26LD350
32LD350,
32LD450
10 0* 10 0 M 4 4
200* 10 0 M 4 4
200* 200 M6 4
AA
BB
RW230 AW-47LG30M
AW-47LG30M
RW120
RW230
Page 23
PREPARATION
23
CABLE MANAGEMENT
For 19/22LD350
After connecting the cables as necessary,
install CABLE HOLDER as shown and bundle
the cables.
K
AC-IN
1
■
Image shown may differ from your TV.
Page 24
PREPARATION
24
CABLE MANAGEMENT
PREPARATION
■
Image shown may differ from your TV.
For 26/32LD350, 32/37/42/47LD450
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Open the CABLE MANAGEMENT CLIP as
shown.
CABLE MANAGEMENT CLIP
1
2
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
3
Page 25
PREPARATION
25
SWIVEL STAND (Except 19/22LD350)
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.
POSITIONING YOUR DISPLAY (For 19/22LD350)
■
Here shown may be somewhat different from your TV.
■
Adjust the position of the panel in various ways for maximum comfort.
• Tilt range
12
0
3
0
Page 26
PREPARATION
26
DESKTOP PEDESTAL INSTALLATION
PREPARATION
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
■
Image shown may differ from your TV.
4 inches
GG
Ensure adequate ventilation by following the clearance recommendations.
GG
Do not mount near or above any type of heat source.
CAUTION
4 inches
4 inches
4 inches
Page 27
PREPARATION
27
ATTACHING THE TV TO A DESK (Except 19/22LD350)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
GG
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
WARNING
1-Screw
(provided as parts of the product)
Desk
Stand
KENSINGTON SECURITY SYSTEM
■
This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on
the back panel. Connect the Kensington Security System cable as
shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington
Security System.
For further information, contact
hhtttt pp:: ////ww ww ww ..kkee nnssiinn ggttoo nn..cc oomm
,
the internet homepage of the Kensington company. Kensington sells
security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
Page 28
PREPARATION
28
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
PREPARATION
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.
■
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
■
Image shown may differ from your TV.
GG
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
GG
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
NOTE
!
Page 29
PREPARATION
29
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wa ll
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Cable TV
Wall Jack
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire
when connecting the antenna.
Copper Wire
■
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
■
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■
If the antenna is not installed properly, contact your dealer for assistance.
ANTENNA
/CABLE IN
■
To prevent damage do not connect to the power outlet until all connections are made between the devices.
■
Image shown may differ from your TV.
ANTENNA
/CABLE IN
Page 30
EXTERNAL EQUIPMENT SETUP
30
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
1. How to connect
Connect the video outputs (Y, P
B
, PR
)
of the digital set-
top box to the
CC OO MMPP OO NN EENN TT IINN VVIIDDEEOO
jacks on
the TV. Match the jack colors (Y = green, P
B
= blue, and
P
R = red).
Connect the audio output of the digital set-top box to
the
CC OO MMPP OO NN EENN TT IINN AA UU DD IIOO
jacks on the TV.
2
1
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box operation.
)
■
Select the
CC oo mmpp oo nn eenntt
input source on the TV using the
IINNPPUU TT
button on the remote control.
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■
This part of EXTERNAL EQUIPMENT SETUP mainly use picture for
3322LLDD33 5500
.
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
VIDEO
AUDIO
R
L(MONO)
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
AV IN 1
VIDEO
YPB PR
L R
AUDIO
COMPONENT IN
Y L RPB PR
1
2
Y, C
B/
PB
, C
R/P
R
Supported Resolutions
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
15.73 59.94
15.73 60.00
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480i
720x480p
1280x720p
1920x1080i
1920x1080p
Signal
480i
480p
720p
10 8 0 i
10 8 0 p
Component
Yes
Yes
Yes
Yes
Yes
HDMI
No
Yes
Yes
Yes
Yes
Page 31
EXTERNAL EQUIPMENT SETUP
31
HDMI Connection
Connect the digital set-top box to the
HHDD MMII //DD VVII
II NN
or
HHDDMMII//DDVVII IINN 11//22
* jack on the TV.
No separate audio connection is necessary.
HDMI supports both audio and video.
1. How to connect
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box.
)
■
Select the
HHDDMMIIorHHDDMMII11//22
* input source on the TV
using the
IINNPPUUTT
button on the remote control.
2
1
RS-232C IN
(
CONTROL&SERV
VIDEO
YPB PR
L
AUDIO
RGB IN (PC)
VIDEO
AUD
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
1
/DVI IN
HDMI OUTPUT
1
HDMI-DTV
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
* HDMI 2: For 26/32LD350
GG
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
NOTE
!
Page 32
EXTERNAL EQUIPMENT SETUP
32
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
RS-232C IN
(
CONTROL&SERVICE)
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AV IN 1
1
/DVI IN
AUDIO IN
(RGB/DVI)
L R
DVI OUTPUT
AUDIO
1
2
GG
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio
connection is necessary.
NOTE
!
Connect the DVI output of the digital set-top box to
the
HHDDMMII//DDVVII IINN
or
HHDDMMII//DDVVII IINN 11
jack on the
TV.
Connect the digital set-top box audio output to the
AAUU DDIIOO II NN ((RRGG BB//DDVVII))
jack on the TV.
1. How to connect
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box.
)
■
Select the
HHDDMMIIorHHDDMMII11
input source on the TV using
the
IINNPPUUTT
button on the remote control.
2
1
Page 33
EXTERNAL EQUIPMENT SETUP
33
DVD SETUP
Component Connection
Component Input ports
To get better picture quality, connect a DVD player to the
component input ports as shown below.
Component ports on the TV
YPB PR
Video output ports
on DVD player
Y
Y
Y
Y
P
B
B-Y
Cb
Pb
P
R
R-Y
Cr
Pr
1 2
Connect the video outputs (Y, PB
, P
R
)
of the DVD to
the
CCOOMMPPOONNEENNTT IINN VVII DDEEOO
jacks on the TV. Match
the jack colors (Y = green, P
B
= blue, and PR = red
)
.
Connect the audio outputs of the DVD to the
CC OO MMPP OO NN EENN TT IINN AA UU DD IIOO
jacks on the TV.
1. How to connect
2. How to use
■
Turn on the DVD player, insert a DVD.
■
Select the
CC oo mmpp oo nn eenntt
input source on the TV using the
IINNPPUU TT
button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
2
1
Y L RPB PR
RS-232C IN
(
CONTROL&SERVICE)
OPTICAL
DIGITAL
(PC)
AUDIO IN
(RGB/DVI)
YPB PR
AUDIO OUT
VIDEO
VIDEO
COMPONENT IN
L(MONO)
AUDIO
L R
AUDIO
R
AV IN 1
ANTENNA
/CABLE IN
Page 34
EXTERNAL EQUIPMENT SETUP
34
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
VIDEO
YPB PR
L R
AUDIO
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
VIDEO
AUDIO
R
L(MONO)
AV IN 1
L R
VIDEO
AUDIO
HDMI Connection
RS-232C I
(
CONTROL&SER
VIDEO
YPB PR
L
AUD
RGB IN (PC)
VIDEO
AU
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
1
/DVI IN
HDMI OUTPUT
1
Connect the
AAUUDD IIOO/VV IIDDEE OO
jacks between TV and
DVD. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red).
1. How to connect
2. How to use
■
Turn on the DVD player, insert a DVD.
■
Select the
AA VV
or
AAVV 11 //22
* input source on the TV using the
IINNPPUU TT
button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
1
Connect the HDMI output of the DVD to the
HHDDMMII//DDVVII II NN
or
HHDDMMII//DDVVII IINN 11//22
jack on the
TV.
No separated audio connection is necessary.
HDMI supports both audio and video.
1. How to connect
2. How to use
■
Select the
HHDDMMII
or
HHDDMMII11 // 22
* input source on the TV
using the
IINNPPUU TT
button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
2
1
* AV2: For 26/32LD350
* HDMI 2: For 26/32LD350
GG
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
NOTE
!
1
Page 35
EXTERNAL EQUIPMENT SETUP
35
VCR SETUP
Antenna Connection
Connect the RF antenna out socket of the
VCR to the
AANNTTEENNNN AA// CC AABBLLEE IINN
sock-
et on the TV.
Connect the antenna cable to the RF
antenna in socket of the VCR.
1. How to connect
■
Set VCR output switch to 3 or 4 and then tune
TV to the same channel number.
■
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.
)
2. How to use
2
1
R
IO
R
AV IN 1
ANTENNA
/CABLE IN
L R
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
AUDIO
Wall Jack
Antenna
1
2
Page 36
EXTERNAL EQUIPMENT SETUP
36
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
GG
If you have a mono VCR, connect the audio cable from
the VCR to the
AAUUDDII OO LL// MMOONNOO
jack of the TV.
NOTE
!
L R
S-VIDEO VIDEO
AUDIO
OUTPUT
SWITCH
ANT IN
ANT OUT
RS-232C IN
(
CONTROL&SERVICE)
ANTENNA
/CABLE IN
VIDEO
YPB PR
L R
AUDIO
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
VIDEO
AUDIO
R
L(MONO)
AV IN 1
1
Connect the
AAUUDD IIOO/VV IIDDEE OO
jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red).
1. How to connect
2. How to use
■
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.
)
■
Select the
AA VV
or
AAVV 11 //22
* input source on the TV using
the
IINNPPUU TT
button on the remote control.
1
* AV2: For 26/32LD350
Page 37
EXTERNAL EQUIPMENT SETUP
37
OTHER A/V SOURCE SETUP
VIDEO
AUDIO
L(MONO)
R
USB IN
AV IN 2
IN 2
H/P
L R
VIDEO
Camcorder
Video Game Set
Connect the
AAUUDDIIOO/VVIIDDEEOO
jacks
between TV and external equipment.
Match the jack colors
.
(
Video = yellow, Audio Left = white, and
Audio Right = red
)
1. How to connect
2. How to use
■
Select the
AA VV 22
* input source on the TV using
the
IINNPPUU TT
button on the remote control.
■
If connected to
AA VV
or
AAVV II NN 11
input, select
the
AA VV
or
AA VV 11
input source on the TV.
■
Operate the corresponding external equipment.
1
1
* AV2: For 26/32LD350
USB CONNECTION (For 32LD350, 32/37/42/47LD450)
IN 2
VIDEO
AUDIO
L(MONO)
R
H/P USB IN
AV IN 2
Memory Key
Connect the USB device to the
UUSSBB II NN
jack on the side
of TV.
1. How to connect
1
2. How to use
■
After connecting the
UUSSBB II NN
jack, you use the USB
function. (
GG
pp..6666
)
1
or
Page 38
EXTERNAL EQUIPMENT SETUP
38
AUDIO OUT CONNECTION
EXTERNAL EQUIPMENT SETUP
Send the TV’s audio to external audio equipment via the Audio Output port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
1
/DVI IN
RS-232C IN
(
CONTROL&SERVICE)
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
AUDIO IN
(RGB/DVI)
AV IN 1
OPTICAL
DIGITAL
AUDIO OUT
1
2
GG
When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (
GG
pp .. 9933
)
NOTE
!
G
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
GG
Audio with ACP (Audio Copy Protection) function may
block digital audio output.
CAUTION
Connect one end of the optical cable to the TV port of
OOPP TTII CCAALL DDIIGGIITTAALL AAUUDDIIOO OOUUTT
.
Connect the other end of the optical cable to the digital audio input on the audio equipment.
Set the “TV Speaker option - Off ” in the AUDIO
menu. (
GG
pp..9933
). See the external audio equipment
instruction manual for operation.
1. How to connect
2
3
1
HEADPHONE SETUP
You can listen to the sound through the headphone.
Plug the headphone into the headphone socket.
To adjust the headphone volume, press the
VVOOLL
+ or
- button. If you press the
MMUUTTEE
button, the sound
from the headphone is switched off.
1. How to connect
2
1
IN 2
VIDEO
AUDIO
L(MONO)
R
AV IN 2
H/P
USB IN
Page 39
EXTERNAL EQUIPMENT SETUP
39
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
1
/DVI IN
RS-232C I
(
CONTROL&SER
VIDEO
YPB PR
L
AUDI
VIDEO
AU
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
RGB IN (PC)
AUDIO IN
(RGB/DVI)
RGB OUTPUT
AUDIO
2
1
Connect the VGA output of the PC to the
RR GG BB IINN
((
PP CC
))
jack on the TV.
Connect the PC audio output to the
AAUU DDIIOO IINN
((
RR GG BB//DDVVII
))
jack on the TV.
1. How to connect
2. How to use
■
Turn on the PC and the TV.
■
Select the
RR GG BB --PPCC
input source on the TV using the
IINNPPUU TT
button on the remote control.
2
1
Page 40
EXTERNAL EQUIPMENT SETUP
40
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
RS-232C IN
(
CONTROL&SERVICE)
VIDEO
YPB PR
L R
AUDIO
RGB IN (PC)
VIDEO
AUDIO
R
L(MONO)
COMPONENT IN
OPTICAL
DIGITAL
AUDIO OUT
AV IN 1
1
/DVI IN
AUDIO IN
(RGB/DVI)
DVI OUTPUT
AUDIO
1
2
Connect the DVI output of the PC to the
HHDD MMII //DD VVII
II NN
or
HHDDMMII//DDVVII IINN 11
jack on the TV.
Connect the PC audio output to the
AAUUDDII OO IINN
((RRGGBB//DDVVII ))
jack on the TV.
1. How to connect
2. How to use
■
Turn on the PC and the TV.
■
Select the
HHDDMMII
or
HHDDMMII11
input source on the TV using
the
IINNPPUU TT
button on the remote control.
2
1
GG
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
NOTE
!
Page 41
EXTERNAL EQUIPMENT SETUP
41
NOTES
!
For 19/22/26/32LD350
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.469 70.08
31.469 70.08
31.469 59.94
37.879 60.31
48.363 60.00
47.776 59.87
47.720 59.799
Resolution
720x400
1360x768
640x480
800x600
1024x768
640x350
1280x768
Supported Display Specifications (RGB-PC, HDMI-PC)
GG
To get the the best picture quality, adjust the PC
graphics card to 1360x768.
GG
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
GG
In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.
GG
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
GG
The synchronization input form for Horizontal and
Vertical frequencies is separate.
GG
Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.
GG
If there are overscan in HDMI-PC 1920x1080,
change aspect ratio to
JJuusstt sscc aann
.
GG
When selecting HDMI-PC, set the “Input Label PC” in the OPTION menu.
Page 42
EXTERNAL EQUIPMENT SETUP
42
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
You can choose the resolution in RGB-PC mode.
The
PPoossiittiioonn, PPhh aa ss ee
, and
SSiizzee
can also be adjusted.
You can use this function only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.
Select
PPII CC TTUU RR EE
.
Select
SSccrr ee ee nn ((RRGG BB--PPCC))
.
Select
RR ee ssoo lluuttiioonn
.
Select the desired resolution.
1
MENU
3
4
2
ENTER
ENTER
ENTER
5
ENTER
Auto Config.
Resolution
Position
Size
Phase
Reset
SCREEN
Move
Prev.
1024 x 768
1280 x 768
1360 x 768
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Page 43
EXTERNAL EQUIPMENT SETUP
43
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Select
SSccrr ee ee nn ((RRGG BB--PPCC))
.
Select
AAuuttoo CCoonnffiigg..
.
Auto Config.
Resolution
Position
Size
Phase
Reset
SCREEN
Move
Prev.
To Set
3
2
ENTER
ENTER
Select
YY eess
.
4
ENTER
Start Auto Configuration.
5
ENTER
Select
PPII CC TTUU RR EE
.
1
MENU
■
If the position of the image is still not
correct, try Auto adjustment again.
■
If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the
PP ooss ii tt ii oo nn, SS ii zzee
or
PPhh aassee
.
Yes No
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Page 44
EXTERNAL EQUIPMENT SETUP
44
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
Select
PPoo ssiitt iioo nn, SSiizz ee
, or
PPhh aassee
.
Make appropriate adjustments.
Auto Config.
Resolution
Position
Size
Phase
Reset
GF
D
E
SCREEN
Move
Prev.
3
ENTER
4
ENTER
■
PPoo ssiitt iioo nn
: This function is to adjust picture to left/right and up/down as you
prefer.
■
SSiizz ee
: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.
■
PP hh aa ss ee
: This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.
Select
PPII CC TTUU RR EE
.
Select
SSccrr ee ee nn ((RRGG BB--PPCC))
.
1
MENU
2
ENTER
5
ENTER
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Page 45
EXTERNAL EQUIPMENT SETUP
45
Screen Reset (Reset to original factory values)
Returns
PPoossiittiioonn, SSiizzee
, and
PPhhaa ss ee
to the default factory settings.
This feature operates only in RGB-PC mode.
Auto Config.
Position
Resolution
Size
Phase
Reset
SCREEN
Move
Prev.
To Set
Select
RR ee sseett
.
3
ENTER
Select
PPII CC TTUU RR EE
.
Select
SSccrr ee ee nn ((RRGG BB--PPCC))
.
1
MENU
2
ENTER
Select
YY eess
.
4
ENTER
5
ENTER
Yes No
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Page 46
WATCHING TV / CHANNEL CONTROL
46
REMOTE CONTROL FUNCTIONS
WATCHING TV / CHANNEL CONTROL
When using the remote control, aim it at the remote control sensor on the TV.
ENERGY
CHVOL
123
4506
789
P
A
G
E
SAVING
TV
AV MODE
INPUT
FAV
RATIO
MUTE
BACK
EXIT
ENTER
MARK
LIST
FLASHBK
MENU
INFO
Q.MENU
POWER
ENERGY SAVING
AV MODE
INPUT
TV
VOLUME UP
/DOWN
MARK
FAV
RATIO
MUTE
CHANNEL
UP/DOWN
PAG E
UP/DOWN
COLOR BUTTON
Turns the TV on from standby or off to standby.
Adjusts the Energy Saving.
GG
pp..8844
Toggles through preset Video and Audio modes.
GG
pp..6622
Rotates through inputs.
Also switches the TV on from standby.
GG
pp..6600
Returns to the last TV channel.
Adjusts the volume.
Select the input to apply the Picture Wizard settings.
GG
pp..7777
Use to mark or unmark a photo/music.
GG
pp..,, 6688,, 7722
Scroll through the programmed Favorite channels.
GG
pp..5588
Changes the aspect ratio.
GG
pp..7744
Switches the sound on or off.
GG
pp..4488
Changes the channel.
Moves from one full set of screen information to the next
one.
Controls USB menu (Photo List and Music List.)
Controls the SIMPLINK compatible devices.
USB,
SIMPLINK
Control buttons
Page 47
WATCHING TV / CHANNEL CONTROL
47
Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
Displays the channel table.
GG
pp..5566
Tunes to the last channel viewed.
Displays the main menu or clears all on-screen displays and return to TV viewing.
Displays channel information at the top of the screen.
GG
pp..5599
Opens the list of Quick Menu options.
GG
pp..5522
Navigates the on-screen menus and adjusts the system settings to your preference.
Allows the user to move return one step in an interactive application or other user interaction
function.
See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu appears at the screen.
GG
pp..6644
— (DASH)
LIST
FLASHBK
MENU
INFO
Q.MENU
THUMBSTICK
(Up/Down/Left
Right/ENTER)
RETURN
SIMPLINK
EXIT
NUMBER button
■
Open the battery compartment cover on the back side and install
the batteries matching correct polarity.
■
Install two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
■
Close cover.
Installing Batteries
Page 48
WATCHING TV / CHANNEL CONTROL
48
TURNING ON THE TV
WATCHING TV / CHANNEL CONTROL
NOTE
!
GG
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
GG
If you do not complete the
IInn iittiiaall sseettttiinn gg
, it will appear whenever the TV is switched on until the
IInnii ttiiaall
ssee tttt iinngg
procedure is completed.
GG
If the TV is unplugged once or turn off with the main power switch on the TV, reset the
CClloocc kk
function.
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■
In standby mode to turn TV on, press the ,
IINNPPUU TT,CC HH ((
DDEE
or
))
button on the TV or press
the
PPOO WWEE RR, IINNPPUU TT, CC HH ((
or )),
NN uummbb ee rr (( 00~99 ))
button on the remote control.
Select the viewing source by using the
IINNPPUU TT
button on the remote control.
■
This TV is programmed to remember which power state it was last set to, even if the power cord is out.
When finished using the TV, press the
PPOO WWEE RR
button on the remote control. The TV reverts to standby
mode.
1
2
3
Press the
CCHH ((
or
))
or
NNUUMMBBEERR
buttons to select a channel number.
1
VOLUME ADJUSTMENT
CHANNEL SELECTION
Press the
VVOOLL ((++
or
--))
button to adjust the volume.
If you want to switch the sound off, press the
MMUUTTEE
button.
You can cancel the Mute function by pressing the
MMUUTTEE
or
VVOOLL ((++
or
--))
button.
Adjust the volume to suit your personal preference.
1
2
3
Page 49
WATCHING TV / CHANNEL CONTROL
49
INITIAL SETTING
This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus.
■
Default selection is “
HHoommee UUssee
”. We recommend setting the TV to “
HHoommee UUssee
” mode for the best pic-
ture in your home environment.
■
“
SSttoo rree DDee mmoo
” Mode is only intended for use in retail environments. Customers can adjust the “
PPiiccttuurree
menu -
PPiicc ttuurree mm ooddee
” manually while inspecting the TV, but the TV will automatically return to preset in-
store mode after 5 minutes.
■
“
SSttoo rree DDee mmoo
” Mode is an optimal setting for displaying at stores. “Store Demo” mode initializes the TV
to set the image quality.
■
You can also adjust
IInn ii ttiiaa ll SSee tttt iinngg
in the
OOPP TTII OO NN
menu.
Check your antenna connection and start
AAuuttoo TTuunnii nngg
.
1
ENTER
Step3. Time setting
Step4. Auto Tuning
Language
Step1. Selecting Language
English
Español
Français
Selecting the environment.
Choose the setting mode you want.
Select [Home Use] to use this TV at home.
To use this TV at Store, select [Store Demo].
Store Demo
Home Use
Mode Setting
Step2. Mode setting
NextPrevious
NextPrevious
Select
AA uuttoo
or
MMaannuu aall
.
Select desired time
option.
1
2
ENTER
Month
Current Time Setting
02
Date
21
Year
2009
Hour
10 AM
Minute
10
Time Zone
Eastern
Daylight Saving
Auto
FF
Auto
GG
Time Setting
NextPrevious
Before starting,
be sure that the
TV antenna is connected.
Auto Tuning
Next
Simple Manual
Previous
INFO
i
Select Menu Language.
1
ENTER
Select
HHoommee UUssee
.
1
ENTER
Page 50
WATCHING TV / CHANNEL CONTROL
50
ON-SCREEN MENUS SELECTION
WATCHING TV / CHANNEL CONTROL
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Display each menu.
Select a menu item.
Accept the current selection.
1
MENU
3
2
ENTER
ENTER
Return to TV viewing.
4
MENU
Enter
Move
Auto Tuning
Manual Tuning
Channel Edit
CHANNEL
CHANNEL
TIME
PICTURE
OPTION
AUDIO
LOCK
Enter
Move
Auto Volume : On
Clear Voice II : On
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
AUDIO
LR
-+
Enter
Move
Clock
Off Time : Off
On Time : Off
Sleep Timer : Off
TIME
Enter
Move
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
LOCK
Enter
Move
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
OPTION
Lock System : Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
For USA For Canada
Enter
Move
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
PICTURE
E E
E
19/22/26LD350
Page 51
WATCHING TV / CHANNEL CONTROL
51
Display each menu.
Select a menu item.
Accept the current selection.
1
MENU
3
2
ENTER
ENTER
Return to TV viewing.
4
MENU
Enter
Move
Auto Tuning
Manual Tuning
Channel Edit
CHANNEL
CHANNEL
OPTION
PICTURE
LOCK
AUDIO
INPUT
TIME
USB
Enter
Move
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
PICTURE
E
Enter
Move
Auto Volume : On
Clear Voice II : On
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
AUDIO
E
Enter
Move
Clock
Off Time : Off
On Time : Off
Sleep Timer : Off
TIME
Enter
Move
Photo List
Music List
USB
Enter
Move
TV
AV1
AV2
Component
RGB-PC
HDMI1
HDMI2
INPUT
Enter
Move
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
LOCK
Lock System : Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
Enter
Move
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
OPTION
For USA For Canada
E
LR
-+
32LD350, 32/37/42/47LD450
Page 52
WATCHING TV / CHANNEL CONTROL
52
QUICK MENU
WATCHING TV / CHANNEL CONTROL
Display each menu.
Make appropriate adjustments.
AAsspp ee cctt RRaattiioo
: Selects your desired picture format.
PPiicc ttuurree MMoodd ee
: Selects the factory preset picture depend on the viewing environment.
SSoo uunndd MMoodd ee
: Selects the factory preset sound for type of program.
MMuull ttii AAuudd iioo
: Changes the audio language (Digital signal).
SSAAPP
: Selects MTS sound (Analog signal).
SSlleeee pp TTiimm ee rr
: Select the amount of time before your TV turns off automatically.
DDeell//AAdddd//FFaavv
: Select channel you want to add/delete or add the channel to the Favorite List.
CC aapp ttiioonn
: Select on or off.
EE nnee rrggyy SS aavv iinngg
: Select the Energy Saving level to reduce the TV’s power consumption by adjusting back-
light.
UUSS BB DD ee vv iiccee
: Select “Eject” in order to eject a USB device.
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
1
Q.MENU
2
3
Q.MENU
Return to TV viewing.
A
16:9
FF
Aspect Ratio
GG
A
16:9
FF
Aspect Ratio
GG
19/22/26LD350 32LD350
A
Page 53
WATCHING TV / CHANNEL CONTROL
53
CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the
channel list.
Run this function if you change your residence or move the TV. Also, make sure to run this function with the
antenna connected during TV broadcasting hours.
Auto Tuning memorizes only the channels available at the time.
Select
CC HH AANN NN EE LL
.
Select
AAuuttoo TTuunnii nngg
.
Select
YY eess
.
Run
AAuuttoo tt uu nniinngg
.
Enter
Move
CHANNEL
Enter
Move
CHANNEL
1
MENU
3
2
ENTER
ENTER
4
ENTER
Auto Tuning
Manual Tuning
Channel Edit
Auto Tuning
Manual Tuning
Channel Edit
■
The TV will ask for a password if parental
control has been activated (LOCK
Menu). Use the password you set up in
the LOCK Menu to allow a channel
search.
■
When setting the Auto tuning or Manual
tuning, the number of maximum channel
you can store is 1000.
It is subject to change depending on the
broadcasting signal environment.
■
Memorizes all the available channels in
the order of DTV, TV, CADTV and CATV.
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Check your antenna connection.
The previous channel information
will be updated during Auto
Tuning.
Yes
No
Page 54
WATCHING TV / CHANNEL CONTROL
54
WATCHING TV / CHANNEL CONTROL
Select
CC HH AANN NN EE LL
.
1
MENU
2
ENTER
When selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received.
Add/Delete Channel (Manual Tuning)
Enter
Move
CHANNEL
Enter
Move
CHANNEL
Channel
Select channel type and
RF-channel number.
FF
DTV
GG
2
Close
Delete
Auto Tuning
Manual Tuning
Channel Edit
DTV 2-1
Bad Normal Good
Select
MMaa nnuuaall TT uunniinn gg
.
Select
DDTTVV, TT VV, CC AADD TT VV
, or
CC AATTVV
.
Select channel you want to add
or delete.
3
ENTER
4
Select
AA dd dd
or
DDee llee ttee
.
5
ENTER
Auto Tuning
Manual Tuning
Channel Edit
■
The TV will ask for a password if parental
control has been activated (LOCK
Menu). Use the password you set up in
the LOCK Menu to allow a channel
search.
■
When setting the Auto tuning or Manual
tuning, the number of maximum channel
you can store is 1000.
It is subject to change depending on the
broadcasting signal environment.
6
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Page 55
WATCHING TV / CHANNEL CONTROL
55
Select a channel.
3
ENTER
The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel Edit
List are displayed in blue.
When a channel number is deleted, it means that you will be unable to select it using
CCHH
button during TV
viewing.
If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select
it in the
CChhaannnn eell EEddiitt
menu.
Channel Editing
Enter
Move
CHANNEL
Auto Tuning
Manual Tuning
Channel Edit
Select
CC HH AANN NN EE LL
.
1
MENU
2
ENTER
Select
CC hhaa nnnnee ll EEddiitt
.
Return to the previous menu.
5
BACK
Return to TV viewing.
MENU
Ch. Change
Page Change
CH
Navigation
Previous
Add/Delete
■
Keep pressing the button and use the
or buttons to move between DTV,
TV, CADTV and CATV.
■
If the channel list is too long, use the
CC HH
or button to move between pages.
Add or delete a channel.
4
BLUE
Page 56
WATCHING TV / CHANNEL CONTROL
56
CHANNEL LIST
WATCHING TV / CHANNEL CONTROL
You can check which channels are stored in the memory by displaying the channel list.
Display the
CC hhaa nnnnee ll LLiisstt
.
1
LIST
Displaying Channel List
Select a channel.
1
Switch to the chosen channel number.
2
ENTER
Selecting a channel in the channel list
Turn the pages.
1
CH
P
A
G
E
Return to TV viewing.
2
BACK
Paging through a channel list
Exit
2-1
3-1
4-1
DTV
DTV
DTV
Channel List
This padlock is displayed
when the channel is locked
with parental control.
Page 57
WATCHING TV / CHANNEL CONTROL
57
FAVORITE CHANNEL SETUP
Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting
for the TV to select all the in-between channels.
To tune to a favorite channel, press the
FFAA VV
(Favorite) button repeatedly.
Return to TV viewing.
4
Q.MENU
Select
FFaavvoorrii ttee
.
3
Select your desired channel.
1
CH
P
A
G
E
123
4506
789
2
Q.MENU
Select
DDeell// AAdd dd// FFaa vv
.
or
A
Favorite
FF
Del/Add/Fav
GG
A
Favorite
FF
Del/Add/Fav
GG
Page 58
WATCHING TV / CHANNEL CONTROL
58
FAVORITE CHANNEL LIST
WATCHING TV / CHANNEL CONTROL
Exit
2-1
3-1
4-1
DTV
DTV
DTV
Favorite List
Select a channel.
1
Switch to the chosen channel number.
2
ENTER
Selecting a channel in the favorite channel list
Turn the pages.
1
CH
P
A
G
E
Return to TV viewing.
2
BACK
Paging through a favorite channel list
Display the Favorite channel list.
1
FAV
MARK
Displaying the favorite channel list
Page 59
WATCHING TV / CHANNEL CONTROL
59
BRIEF INFORMATION
1
INFO
Brief Info shows the present screen information.
Show the Brief Info on the screen.
2
BACK
Return to TV viewing.
Brief Info Title Test..
Sat, Feb 21, 2009 10:10 AM 11:40 AM
CNN
DOLBY DIGITAL
10:40 AM
Multilingual CaptionD 1080i TV-PG D L S V
CC
Program title
Day, Month, Year
Program start time
Program progress bar
Program finish time
Present time
Banner information
1 2 3 4 5 67
1
2
3
4
5
6
7
MMuullttiilliinngguuaall
: The program contains two or more audio services. Use
the
QQ.. MMEENN UU
menu to select wanted Audio.
CCaappttiioonn
: The program contains one or more caption services. Use
the
QQ.. MMEENN UU
menu to select wanted Closed caption.
DDoollbbyy DDiigg iittaa ll
: The program contains a Dolby Digital audio signal
in TV and HDMI input source.
The original aspect ratio of the video is 4:3
The original aspect ratio of the video is 16:9 (wide)
The video resolution is 720x480i
The video resolution is 720x480p
The video resolution is 1280x720p
The video resolution is 1920x1080i
The video resolution is 1920x1080p
VV --CChhiipp
: The program contains V-Chip information. Refer to the
LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex), V
(Violence), FV (Fantasy Violence)
480i
480p
720p
10 8 0 i
10 8 0 p
4:3
16:9
CC
D
Page 60
WATCHING TV / CHANNEL CONTROL
60
INPUT LIST
WATCHING TV / CHANNEL CONTROL
TV AV Component
HDMI RGB-PC
19/22LD350:
TV AV1 AV2
HDMI2 HDMI1 RGB-PC
Component
26/32LD350:
Select the desired input source.
■
32LD350: You can also select the desired input source in the
IINNPPUUTT
menu.
1
INPUT
ENTER
TV AV Component RGB-PC HDMI1
TV AV Component RGB-PC HDMI1
Input Label
Exit
Select a desired input source (except
TT VV
).
Then, you can select your desired
II nnpp uutt
LLaabb ee ll
with using Blue button.
GG
pp..66 11
ie)
ie) In case of changing the input label using Blue button
Only these input signals which are connected to a TV can be activated and selected.
■
TT VV
: Select it to watch over-the-air, cable and digi-
tal cable broadcasts.
■
AA VV
: Select them to watch a VCR or other external
equipment.
■
CC oo mmpp oo nn eenntt
: Select them to watch DVD or a
Digital set-top box.
■
RR GG BB --PPCC
: Select it to view PC input.
■
HHDD MM II
: Select them to watch high definition
devices.
VCR DVD PC Game
■
When new external device is connected, this popup menu is
displayed automatically.
If selecting
YY eess
, you can select input source that you want to
appreciate.
■
But, when selecting “
SSII MMPP LL IINN KK- OOnn
”, popup menu for HDMI
input will not be displayed.
No
Yes
!
New external input is connected.
Do you want to use this?
AV2
Disconnected inputs are inactive (grayed out)
Page 61
WATCHING TV / CHANNEL CONTROL
61
INPUT LABEL
This indicates which device is connected to which input port.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
AV
Component
RGB-PC
HDMI
FF GG
Close
Select
OOPP TTII OONN
.
Select
IInnppuutt LL aabb ee ll
.
Select the label.
1
MENU
2
ENTER
Select the source.
3
ENTER
4
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
With using OPTION menu
Select the source.
Select the label.
1
INPUT
2
3
BACK
Return to the previous menu.
MENU
Return to TV viewing.
With using INPUT button
19/22LD350
AV1
AV2
Component
RGB-PC
HDMI1
HDMI2
FF GG
Close
26/32LD350
EE
BLUE
Page 62
WATCHING TV / CHANNEL CONTROL
62
AV MODE
WATCHING TV / CHANNEL CONTROL
AV Mode toggles through preset Video and Audio settings.
1
AV MODE
2
Off Cinema
Game Sport
Press the
AAVV MM OO DDEE
button repeatedly to
select the desired source.
ENTER
■
If you select “
CC iinnee mmaa
” in AV mode,
CC iinnee mmaa
will be selected both for “PICTURE menu - Picture Mode” and “AUDIO
menu - Sound Mode” respectively.
■
If you select “
OOffff
” in AV mode, the
“
PPiicc ttuurree MMoodd ee
” and “
SSoo uunndd MMoodd ee
”
return to previous selected value.
■
OOffff
: Disables the AV MODE.
■
CC iinnee mmaa
: Optimizes video and audio for
watching movies.
■
SSpp oorrtt
: Optimizes video and audio for
watching sports events.
■
GGaa mm ee
: Optimizes video and audio for
playing games.
SIMPLE MANUAL
You can easily and effectively access the TV information by viewing a simple manual on the TV.
During the Simple Manual operation, audio will be muted.
Select
OOPP TTII OONN
.
Select
SSiimm ppll ee MMaa nnuuaa ll
.
1
MENU
2
ENTER
Select the part of the manual you
want to see.
3
ENTER
4
BACK
Return to TV viewing.
Working
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
EE
Page 63
WATCHING TV / CHANNEL CONTROL
63
KEY LOCK
The TV can be set up so that it can only be used with the remote control.
This feature can be used to prevent unauthorized viewing by locking out the front panel controls.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
Select
OOPP TTII OONN
.
Select
KKeeyy LLoocckk
.
1
MENU
2
ENTER
Select
OO nn
or
OOffff
.
3
ENTER
■
In
KKee yy LLoocckk‘OO nn
’, if the TV is turned off,
press the
rr
/ I, INPUT, CH
((
DDEE
or
))
button on the TV or POWER, INPUT,
CH
(( ))
or NUMBER buttons on the
remote control.
■
With the
KKee yy LLoocckk OO nn
, the display
‘
KKee yy LLoo cc kk
’ appears on the screen if
any button on the front panel is pressed
while viewing the TV.
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
!
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : On
Simple Manual
Caption : Off
Set ID : 1
EE
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
EE
Off
On
Page 64
WATCHING TV / CHANNEL CONTROL
64
WATCHING TV / CHANNEL CONTROL
SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional
cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the
logo are fully supported.
SIMPLINK can be turned on and off in the user menus.
Enter
Move
OPTION
Select
OOPP TTII OONN
.
Select
SSII MMPPLLIINNKK
.
Select
OOnn orOOffff
.
Enter
Move
OPTION
E
1
MENU
3
2
ENTER
ENTER
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Off
On
NOTE
!
GG
Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
GG
When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device
will stop.
GG
When you select a device with home theater functionality, the sound output automatically switches to
the home theater speakers and the TV speakers are turned off.
GG
If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL
AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIMPLINK device with an OPTICAL cable.
E
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Page 65
WATCHING TV / CHANNEL CONTROL
65
■
DDii rree cctt PP llaa yy::
After connecting AV devices to the TV, you can directly control the devices and play media with-
out additional settings.
■
SSee lleecctt AAVV ddeevvii ccee ::
Enables you to select one of the AV devices connected to TV.
■
DDiisscc ppllaayybb aa cckk::
Control connected AV devices by pressing the ,
ENTER, G, A,
ll ll
, FFand GGbuttons.
■
PPoowweerr ooffff aallll ddeevviicceess::
When you power off the TV, all connected devices are turned off.
■
SSwwiittcchh aa uudd iioo--oo uutt::
Offers an easy way to switch audio-out.
■
SSyynncc PP oowweerr oonn::
When the equipment with Simplink function connected HDMI terminal starts to play, The TV
will change automatically to turn on mode.
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide
this function)
Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC: Consumer
Electronics Control).
SIMPLINK Menu
TTVV vv iiee ww iinngg
: Switch to the previous TV
channel regardless of the current mode.
DDIISSCC ppllaayy bb aacckk
: Select and play discs.
When multiple discs are available, the titles
of discs are conveniently displayed at the
bottom of the screen.
VV CCRR ppll aayybb aacc kk
: Control the connected
VCR.
HHDDDD RReeccoorrddiinn ggss ppllaayy bb aacc kk
: Control
recordings stored in HDD.
AAuudd iioo OOuutt ttoo HHoomm ee TThheeaatteerr ssppee aakk--
eerr //AAuu ddii oo OOuu tt ttoo TTVV
: Select Home
Theater speaker or TV speaker for Audio
Out.
SIMPLINK Functions
1
2
3
4
5
GG
When no device is connected
(displayed in gray)
GG
Selected Device
GG
When a device is connected
(displayed in bright color)
1
2
3
4
5
Display
SSII MMPPLLIINN KK
menu.
Select the desired device.
Control connected AV devices.
1
3
2
ENTER
ENTER
Page 66
ENTRY MODES
USB
66
USB (For 32LD350, 32/37/42/47LD450)
Precautions when using the USB device
GG
Only a USB storage device is recognizable.
GG
If the USB storage device is connected through a
USB hub, the device is not recognizable.
GG
A USB storage device using an automatic recognition program may not be recognized.
GG
A USB storage device which uses its own driver
may not be recognized.
GG
The recognition speed of a USB storage device
may depend on each device.
GG
Please do not turn off the TV or unplug the USB
device when the connected USB storage device is
working. When such device is suddenly separated
or unplugged, the stored files or the USB storage
device may be damaged.
GG
Only use a USB storage device which has normal
music files or image files.
GG
Please use only a USB storage device which was
formatted as a FAT 32 or NTFS file system provided with the Windows operating system. In case of
a storage device formatted as a different utility
program which is not supported by Windows, it
may not be recognized.
GG
Please connect power to a USB storage device
(over 0.5A) which requires an external power supply. If not, the device may not be recognized.
GG
Please connect a USB storage device with cable is
offered by USB maker. If connected with cable is
not offered by USB maker or an excessively long
cable, the device may not be recognized.
GG
Some USB storage devices may not be supported
or operate properly.
GG
Please backup important files because data on
USB device may be damaged. Data management is
consumer's responsibility and as a result, the manufacturer does not cover data damage.
GG
If your USB memory device has multiple partitions,
or if you use a USB multi-card reader, you can use
up to 4 partitions or USB memory devices.
GG
In case of USB storage devices formatted as NTFS,
deletion is not allowable.
GG
File alignment method of USB storage device is
similar to Window XP and file name can recognize
up to 100 English characters.
GG
The recommended capacity is 1TB or less for a
USB external hard disk and 32 GB or less for USB
memory.
GG
If a USB external hard disk with a “Energy Saving”
function doesn’t work, turn the hard disk off and
on again to make it work properly. Refer to the
user manual of the application USB external hard
disk.
When removing the USB device
Connect the USB device to the
UUSSBB IINN
jacks on the side of TV.
3
Select
PPHH OO TTOO LLIISSTTorMMUUSS IICC LL IISSTT
.
1
IN 2
USB IN
Memory Key
PHOTO LIST MUSIC LIST
Select
UUSS BB DD ee vv iiccee
.
Select
EE jj eecctt
.
Select the
UUSS BB DD ee vv iiccee
menu before removing the
USB device.
2
ENTER
1
Q.MENU
2
ENTER
■
This TV supports JPG and MP3 files.
When you connect a USB device, this pop up menu is displayed automatically.
When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu.
In USB device, you can not add a new folder or delete the existing folder.
Page 67
PHOTO LIST
USB
67
You can view .JPG files from USB storage devices.
The On Screen Display on your model may be slightly different.
Screen Components
Moves to upper level folder
Preview: Display the
thumbnail/folder name of
the photo in the selected
folder
Current page/Total pages
Total number of marked photos
Corresponding buttons on
the remote control
Supported photo file: *.JPG
■
You can play JPG files only.
■
Only baseline scan is supported among JPG.
■
Available JPG size (width x height, pixel): 64 x 64 - 15360 x 8640
Select
UUSS BB
.
Select
PPhhoo ttoo LLii sstt
.
2
1
MENU
ENTER
ENTER
1
2
3
4
5
Navigation Popup Menu Page Change Mark Exit
CH
MARK
5
Page 2/3
No Marked
Photo List
Up Folder
1366x768, 125KB
KY101
06/10/2008
KY102
04/03/2008
JMJ001
01/01/2000
JMJ002
06/15/2008
JMJ003
04/03/2008
JMJ004
02/18/2008
KY103
03/30/2008
KY104 06/19/2008
KY105
01/31/2008
JMJ005
05/13/2008
JMJ006
05/26/2008
JMJ007
02/18/2008
JMJ008
02/18/2008
Up Folder
Drive1
JMJ001
3 4
2
1
Page 68
USB
68
USB
Photo Selection and Popup Menu
Select the target folder or drive.
Select the desired photos.
2
Show the Popup menu.
3
1
■
Use the
CC HH
button to navigation in the
photo page.
■
Use the
MMAARRKK
button to mark or unmark a
photo. When one or more photos are marked,
you can view individual photos or a slide show
of the marked photos. If no photos are marked,
you can view all photos individually or all photos in the folder in a slide show.
4
Select the desired Popup menu.
ENTER
ENTER
ENTER
Page 2/3
No Marked
Photo List
Up Folder
1366x768, 125KB
KY101
06/10/2008
KY102
04/03/2008
JMJ001
01/01/2000
JMJ002
06/15/2008
JMJ003
04/03/2008
JMJ004
02/18/2008
KY103
03/30/2008
KY104
06/19/2008
KY105
01/31/2008
JMJ005
05/13/2008
JMJ006
05/26/2008
JMJ007
02/18/2008
JMJ008
02/18/2008
Up Folder
Page 2/3
No Marked
Photo List
Up Folder
1366x768, 125KB
KY101
06/10/2008
KY102
04/03/2008
JMJ001
01/01/2000
JMJ002 06/15/2008
JMJ003
04/03/2008
JMJ004
02/18/2008
KY103
03/30/2008
KY104
06/19/2008
KY105
01/31/2008
JMJ005
05/13/2008
JMJ006 05/26/2008
JMJ007
02/18/2008
JMJ008
02/18/2008
Up Folder
Drive1
Drive1
JMJ001
JMJ001
1366x768, 125KB
View
Mark All
Delete
Close
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
When you select a file (not folder), this PopUp
menu is displayed.
GG
VViieeww
: Display the selected item.
GG
MMaarrkk AAllll
: Mark all photos on the screen.
GG
UUnnmm aarrkk AAllll
: Deselect all marked photos.
GG
DDee llee ttee
: Delete the selected photo item.
GG
CC lloo ssee
: Close the pop-up menu.
Page 69
USB
69
Full Screen Menu
You can change the Photo List view so that it fills the screen. More operations are available in full
screen mode.
■
Use the
CC HH
button to navigation in the
photo page.
Select the target folder or drive.
Select the desired photos.
Show the Popup menu.
5
Select
VV ii ee ww
.
The selected photo is displayed in
full size.
2
3
1
4
ENTER
ENTER
ENTER
Page 2/3
No Marked
Photo List
Up Folder
1366x768, 125KB
KY101
06/10/2008
KY102
04/03/2008
JMJ001 01/01/2000
JMJ002 06/15/2008
JMJ003 04/03/2008
JMJ004
02/18/2008
KY103
03/30/2008
KY104
06/19/2008
KY105
01/31/2008
JMJ005 05/13/2008
JMJ006 05/26/2008
JMJ007 02/18/2008
JMJ008 02/18/2008
Up Folder
Page 2/3
No Marked
Photo List
Up Folder
1366x768, 125KB
KY101
06/10/2008
KY102
04/03/2008
JMJ001
01/01/2000
JMJ002
06/15/2008
JMJ003
04/03/2008
JMJ004
02/18/2008
KY103
03/30/2008
KY104
06/19/2008
KY105
01/31/2008
JMJ005
05/13/2008
JMJ006
05/26/2008
JMJ007
02/18/2008
JMJ008
02/18/2008
Up Folder
Drive1
Drive1
JMJ001
JMJ001
1366x768, 125KB
View
Mark All
Delete
Close
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
The aspect ratio of a photo may change the size of
the photo displayed on the screen in full size.
1/17
Slideshow BGM Del ete Option H ide
Page 70
USB
70
USB
Select the
SSlliiddeesshhooww, BBGGMM
,
((RRoottaattee))
,
DDeelleettee,OOppttiioonn
, or
HHiiddee..
■
Use button to select the previous or
next photo.
■
Use button to select and control
the menu on the full-sized screen.
ENTER
6
NOTE
!
GG
This TV will not be able to decode
most JPG images saved using the
Progressive option.
1/17
Slideshow BGM Delete Option Hide
Press
FF GG
to set the time interval between slides.
Slide Speed
Fast
Cancel
...
Music Album
Enter
GG
SSlliiddee ss hhoo ww
: Selected photos are displayed during the
slide show. If no photo is selected, all photos in the current folder are displayed during slide show.
■
Set the time interval of the slide show in
OOppttiioonn
.
GG
BB GGMM
: Listen to music while viewing photos in full size.
■
Set the BGM device and album in
OOppttiioonn
.
GG
((RRoottaattee ))
: Rotate photos.
■
Rotates the photo 90°, 18 0 °, 270°, 360° clockwise.
■
Photo cannot be rotated if its width is greater than
the available supported resolution height.
GG
DDee llee ttee
: Delete photos.
GG
OOppttiioonn
: Set values for
SSllii ddee SSppee eedd
and
MMuu ss iicc
AAllbb uu mm
.
■
Use button and
EE NN TTEE RR
button to set
values. Then go to and press
EE NN TTEE RR
to save
the settings.
■
You cannot change
MMuussiicc AA llbb uu mm
while BGM is
playing.
GG
HHiiddee
: Hide the menu on the full-sized screen.
■
To see the menu again on the full-sized screen, press
EE NN TTEERR
button to display.
Page 71
MUSIC LIST
USB
71
You can use the Music List menu to play MP3 files from a USB storage device.
This TV cannot play back copy-protected files.
The On Screen Display on your model may be slightly different.
Screen Components
Supported music file: *.MP3
Bit rate range 32 Kbps - 320 Kbps
• Sampling rate (Sampling Frequency)
MPEG1 layer 3: 32 kHz, 44.1 kHz, 48 kHz
MPEG2 layer 3: 16 kHz, 22.05 kHz, 24 kHz
MPEG2.5 layer 3: 8 kHz, 11.025 kHz, 12 kHz
Moves to upper level folder
Preview: If any album jacket
for the file exists, this jacket is displayed.
Current page/Total pages
Total number of marked
musics
Corresponding buttons on
the remote control
1
3
4
5
2
Select
UUSS BB
.
Select
MMuussiicc LLii sstt
.
1
2
MENU
ENTER
ENTER
Music List
Up Folder
Title Duration
3 4
2
1
Page 2/3
No Marked
Drive1
Navigation Popup Menu Page Change Mark Exit
CH
MARK
5
AA
00:00 / 04:16
Up Folder
Page 72
USB
72
USB
Music Selection and Popup Menu
■
Use the
CC HH
button to navigation in
the music page.
■
Use
MMAARRKK
button to mark or unmark a music
file. If no music is marked, all the music in the
folder will be played in sequence. When one or
more music files are marked, the marked music
files will be played in sequence. If you want to
listen to only one song repeatedly, just mark
that one file and play.
Select the target folder or drive.
Select the desired musics.
Show the Popup menu.
Select the desired Popup menu.
2
3
1
4
ENTER
ENTER
ENTER
5
BACK
Return to TV viewing.
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
Navigation Page Change Mark Exit
CH
MARK
Popup Menu
Page 2/3
No Marked
Music List
Up Folder
AA
00:00 / 04:16
Up Folder
Drive1
Title
Duration
Page 2/3
No Marked
Music List
Up Folder
AA
00:00 / 04:16
Up Folder
Drive1
Title
Duration
3945 KB
128 Kbps
Play
Play with Photo
Mark All
Delete
Close
GG
PPllaa yy
(During stop): Play the selected music.
Once a song finishes playing, the next selected
one will be played. When there are no selected
musics to play, the next one in the current folder will be played. If you go to a different folder
and press the
EE NN TTEE RR
button, the current
music in playback will stop.
GG
PPllaa yy MM aa rr kkee dd
: Play the selected musics. Once
a music finishes playing, the next selected one
will be played automatically.
GG
SSttoo pp PPllaa yy
(During playback): Stop the play-
ing musics.
GG
PPllaa yy ww iitt hh PPhhoottoo
: Start playing the selected
musics and then move to the Photo List.
GG
MMaarrkk AAllll
: Mark all musics in the folder.
GG
UUnnmm aarrkk AAllll
: Deselect all marked music.
GG
DDee llee ttee
: Delete the selected music.
GG
CC lloo ssee
: Close the pop-up menu.
Page 73
USB
73
■
The play information box (as shown below) will automatically
move across the screen when there is no user input to prevent a fixed image remaining on the screen for a extended
period of time.
NOTE
!
GG
When music is playing, is displayed in front of the music play time.
GG
A damaged or corrupted music file that does not play displays 00:00 as the play time.
GG
Music files with copy-protection will not play.
GG
Press
EE NN TTEE RR
, AA, or
RR EE TTUU RR NN
button to stop the screen saver.
Page 74
PICTURE CONTROL
74
PICTURE SIZE (ASPECT RATIO) CONTROL
PICTURE CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
HDMI/RGB-PC input source use 4:3 or 16:9 aspect ratio. But you can select all aspect ratios in HDMI-PC
1920X1080 input.
You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting,
aux).
■
You can also adjust
AAsspp ee cctt RRaattiioo
in
the
QQ..MMEE NNUU
.
■
Press the
RR AATTII OO
button repeatedly to
select the desired picture format.
Enter
Move
PICTURE
E
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
16:9
Just Scan
Set By Program
4:3
Zoom
Cinema Zoom 1
Select
PPII CC TTUU RR EE
.
Select
AAsspp ee cctt RRaattiioo
.
Select the desired picture format.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Page 75
PICTURE CONTROL
75
16:9
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
Just Scan
Normally the edges of video signals are cropped
1-2%. Just Scan turns off this cropping and
shows the complete video.
Notes: If there is noise on the edges of the original
signal, it will be visible when Just Scan is activated.
JJuusstt SSccaann
operates only in
DTV/CADTV/Component/HDMI-DTV/DVI-DTV
(720p/1080i/1080p) input source.
Set By Program
Selects the proper picture proportion to match
the source’s image.
4:3
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
Zoom
Choose Zoom when you want to view the picture
without any alteration. However, the top and
bottom portions of the picture will be cropped.
■
When adjusting in Q.MENU menu,
a. or button: Adjust proportion of Zoom.
b. or button: Move the image on the screen.
Cinema Zoom
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
This enlarges an image with cinemascope aspect
ratio (2.35:1) without distortion.
Note: When enlarging or reducing the picture,
the image may become distorted.
■
or button: Adjust proportion of
Cinema Zoom. The adjustment range is 1-16.
■
or button: Move the image on the screen.
Just Scan
(4:3 4:3)
(16:9 16:9)
Set By Program
Set By Program
Page 76
PICTURE CONTROL
76
PICTURE WIZARD
PICTURE CONTROL
Select
PPII CC TTUU RR EE
.
Select
PPiiccttuurree
WWiizzaarr dd
.
1
MENU
2
ENTER
ENTER
Adjust
PPiicc ttuurree WWiizzaarrdd
.
Adjust
WWhhiitt ee LLeevveell
.
3
ENTER
Adjust
BB llaacckk LLeevveell
.
4
ENTER
5
ENTER
Adjust
HHoorrii zz oonntt aa ll
SShhaarrppnneessss
.
8
ENTER
Adjust
CC oo ll oo rr
.
6
ENTER
Adjust
TT iinn tt
.
7
ENTER
Picture Wizard
With Picture Wizard, you can adjust the picture quality of the
original image.
G
Black Level
Set the screen above identical to the Recommended sample
below.
NextPrevious
NextPrevious
• Brightness 50
EE
EE
Low HighRecommended
Color
Set the screen above identical to the Recommended sample
below.
NextPrevious
• Color 50
EE
EE
Low HighRecommended
White Level
Set the screen above identical to the Recommended sample
below.
NextPrevious
Low HighRecommended
• Contrast 90
EE
EE
Tint
Set the screen above identical to the Recommended sample
below.
NextPrevious
Low HighRecommended
• Tint 0
EE
EE
RG
Horizontal Sharpness
Set the screen above identical to the Recommended sample
below.
NextPrevious
• H Sharpness 50
EE
EE
Low HighRecommended
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
This feature lets you adjust the picture quality of the
original image.
Use this to calibrate the screen quality by adjusting
the Black and White Level etc. You can calibrate the
screen quality by easily following each step.
When you adjust the image to
LL oo ww
,
RReeccoommmmeenn dd ee dd
or
HH ii gghh
, you can see the example
of the changes you made.
Page 77
PICTURE CONTROL
77
Select input source to apply the
settings.
14
FAV
MARK
Adjust
VV ee rrttiicc aall
SShhaarrppnneessss
.
9
ENTER
Adjust
BB aacckkll ii gghhtt
.
13
ENTER
Finish the Picture Wizard.
16
ENTER
Save.
15
ENTER
Complete
ConfirmMovePrevious
Vertical Sharpness
Set the screen above identical to the Recommended sample
below.
NextPrevious
• V Sharpness 50
EE
EE
Low HighRecommended
Backlight
Set the Backlight to your Brightness preference.
NextPrevious
• Backlight 50
EE
EE
Dark BrightRecommended
DTV
TV
AV1
AV2
Component
RGB-PC
HDMI1
HDMI2
Select (an) input(s) to apply the settings.
Warning: The picture quality may vary according to the
different types of signal and inputs.
E
E
Mark
MARK
■
If you stop the setting before the final
step, the changes will not be saved to
the TV.
■
Once the
PPiicc ttuurree WWii zzaarrdd
sets the pic-
ture quality,
EE nnee rrggyy SSaavv iinngg
is changed
to
OOffff
automatically.
Close
The current adjustment value is saved to
Expert1.
i
Adjust
CC oo ll oo rr
TTee mmpp ee rr aa ttuurree
.
10
ENTER
Color Temperature
Set the Color Temperature as you like. Refer to the samples
below.
NextPrevious
• Color Temperature Warm
EE
EE
Warm CoolMedium
Adjust
DDyynnaa mmiicc
CC oo nnttrraasstt
.
11
ENTER
Dynamic Contrast
Set the Dynamic Contrast as you like. Refer to the samples
below.
NextPrevious
• Dynamic Contrast Off
EE
EE
Off HighMedium
Adjust
CC oo lloo rr GGaaii nn
.
12
ENTER
Color Gain
Set the Color Gain as you like. Refer to the samples below.
NextPrevious
• Color Gain Original
EE
EE
Original HighMedium
Page 78
PICTURE CONTROL
78
PRESET PICTURE SETTINGS (PICTURE MODE)
PICTURE CONTROL
There are factory presets for picture settings available in the user menus. You can use a preset, change each
setting manually.
Enter
Move
PICTURE
E
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
Select
PPII CC TTUU RR EE
.
Select
PPiicc ttuurree MMoodd ee
.
Select
VViivviidd,SStt aann ddaarrdd, NN aattuurraa ll
,
CCiinn ee mmaa, SSpp oo rrtt
, or
GGaa mmee
.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Vivid
Standard
Natural
Cinema
Sport
Game
Expert1
Expert2
■
VV iivvii dd, SStt aann ddaarrdd, NN aattuurraall, CCiinneemmaa
,
SSpp oo rrtt
, and
GGaa mmee
Settings are preset for
the optimum picture quality at the factory.
■
VV iivviidd
: This is the mode to maximize the
effect of the video in the retail store.
Strengthen the contrast, brightness,
color and sharpness for vivid picture.
■
SSttaa nnddaa rrdd
: This is the mode to realize
optimum viewing condition for the general user.
■
NN aatt uu rraall
: This is the mode to display the
most natural screen status.
■
CC iinnee mmaa
: This mode optimizes video for
watching movies.
■
SS pp oo rrtt
: This is the video mode to
emphasize dynamic video and primary
color (e.g, white, uniform, grass, sky blue
etc.) by realizing the optimal screen for
sports.
■
GGaa mm ee
: This is the mode to realize fast
response speed in a fast gaming screen.
■
EE xx ppee rrtt
: This is the mode to adjust the
video in detail for video quality expert
and general user.
■
You can also adjust
PPiicc ttuurree MM oo ddee
in
the
QQ.. MMEE NNUU
.
Page 79
PICTURE CONTROL
79
MANUAL PICTURE ADJUSTMENT - USER MODE
Adjust the picture appearance to suit your preference and viewing situations.
Select
PPII CC TTUU RR EE
.
Make appropriate adjustments.
Select
BB aacckkll ii gghhtt, CC oo nnttrraasstt, BB rriigghhtt nnee ss ss
,
SShhaarrppnneessss, CC oo ll oo rr
, or
TT iinn tt
.
1
MENU
Select
PPiicc ttuurree MMoodd ee
.
2
ENTER
Select
VViivviidd,SStt aann ddaarrdd, NN aattuurraa ll
,
CCiinn ee mmaa, SSpp oo rrtt
, or
GGaa mmee
.
3
ENTER
4
ENTER
5
ENTER
6
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
• Backlight 70
EE
EE
EE
EE
Enter
■
When adjusting Energy Saving,
BB aacckkll ii gghhtt
function is disabled.
■
BB aacckkll ii gghhtt
: This function adjusts the
brightness of LCD panel, to control the
brightness of the screen. Adjusting the
backlight is recommended when setting
the brightness of the set. When decreasing the backlight, the brightness of the
black becomes darker without any loss in
video signal and the power consumption
is reduced.
■
CC oo nnttrraasstt
: Increase or decrease the gradient of the video signal. You may use
Contrast when the bright part of picture
is saturated.
■
BB rriigghhtt nnee ss ss
: Adjusts the base level of
the signal in the picture. You may use
Brightness when the dark part of the picture is saturated.
■
SShhaarrppnneessss
: Adjusts the level of crispness in the edges between the light and
dark areas of the picture. The lower the
level, the softer the image.
■
CC oo ll oo rr
: Adjusts intensity of all colors.
■
TT iinn tt
: Adjusts the balance between red
and green levels.
Page 80
PICTURE CONTROL
80
PICTURE IMPROVEMENT TECHNOLOGY
PICTURE CONTROL
Select
PPII CC TTUU RR EE
.
Select
AAdd vv aanncceedd CCoonnttrroo ll
.
Select your desired options.
1
MENU
3
2
ENTER
ENTER
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Make appropriate adjustments.
4
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Color Temperature
FF
Medium
GG
Dynamic Contrast
Off
Dynamic Color
Off
Noise Reduction
Off
Gamma
Medium
Black Level
Low
Eye Care
Off
Real Cinema
Off
Close
E
You can calibrate the screen for each Picture Mode or set the video value according to the special video screen.
You can set the video seeing differently for each input.
To reset to the factory default after making adjustments to each input source, execute the
PPiicctt uurr ee RR ee ssee tt
function for each
PPiicctt uurr ee MM oo dd ee
.
Page 81
PICTURE CONTROL
81
EXPERT PICTURE CONTROL
Select
PPII CC TTUU RR EE
.
Select
PPiicc ttuurree MMoodd ee
.
Select
EE xx pp eerrtt CCoo nntt rroo ll
.
Select
EE xx ppeerrtt11
or
EE xx ppeerrtt22
.
1
MENU
3
2
ENTER
ENTER
4
ENTER
Make appropriate adjustments.
6
By segmenting categories,
EExxppee rrtt11
and
EExxppee rrtt22
provide more categories which users can set as they see
fit, offering the optimal picture quality for users.
This may also be used be a professional to help optimize the TV performance in the environment the TV is in.
7
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
PICTURE
E
RG
• Brightness 50
• H Sharpness 50
• V Sharpness 50
• Color 50
• Tint 0
• Expert Control
• Picture Reset
Screen (RGB-PC)
Dynamic Contrast
FF
Off
GG
Noise Reduction
Low
Gamma
Off
Black Level
Low
Real Cinema
Off
Color Standard
SD
Color Gamut
Standard
Edge Enhancer
High
xvYCC
Auto
Close
E
Select your desired menu option.
5
ENTER
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Expert1
• Backlight 80
• Contrast 90
• Brightness 50
• H Sharpness 50
Vivid
Standard
Natural
Cinema
Sport
Game
Expert1
Expert2
Page 82
PICTURE CONTROL
82
PICTURE CONTROL
■
Set to warm to enhance hotter colors such as red, or set to cool to make picture
bluish.
■
Adjusts the contrast to keep it at the best level according to the brightness of the
screen. The picture is improved by making bright parts brighter and dark parts darker.
■
Adjusts screen colors so that they look livelier, richer and clearer. This feature
enhances hue, saturation and luminance so that red, blue, green and white look
more vivid.
■
Reduces screen noise without compromising video quality.
Low : Make dark and middle gray level area of the picture brighter.
Medium: Express original picture levels.
High: Make dark and middle gray level area of the picture darker.
■
You can adjust brightness of dark area and middle gray level area of the picture.
Low: The reflection of the screen gets darker.
High: The reflection of the screen gets brighter.
Auto: Realizing the black level of the screen and set it to High or Low automatically.
■
Set black level of the screen to proper level.
■
This function enables to select 'Low' or 'High' in the following mode: AV (NTSC-M),
HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
*This feature is not available for all models.
■
Adjust the brightness of the screen to prevent the screen from being too bright.
Dims extremely bright pictures.
■
This feature is disabled in “
PPiicc ttuurree MM ooddee --VVii vv iidd, CC iinnee mmaa
”.
■
Makes video clips recorded in film look more natural by eliminating judder effect.
Dynamic Contrast
Dynamic Color
Noise Reduction
Gamma
Black Level
Eye Care
Real Cinema
Color Temperature
(Advanced Control)
Page 83
PICTURE CONTROL
83
■
Convert the color of a different video to HD color.
■
Adjusts the overall color of the screen by changing the color of white.
a. Method : 2 Points
- Pattern: Inner, Outer
- Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50.
b. Method : 10 Point IRE
- Pattern: Inner, Outer
- IRE (Institute of Radio Engineers) is the unit to display the size of the video signal
and can be set among 10, 20, 30 - 100. You can adjust Red, Green or Blue according to each setting.
- Luminance: This function displays calculated luminance value for 2.2 gamma. You can
input luminance value you want at 100 IRE, than the target luminance value for 2.2
gamma is displayed at every 10 steps from 10 IRE to 90 IRE.
- Red/Green/Blue: The adjustment range is -50 - +50.
■
As the tool used by the experts to make adjustments by using the test patterns, this
does not affect other colors but can be used to selectively adjust the 6 color areas
(Red/Green/Blue/Cyan/Mgt/Yellow).
Color difference may not be distinctive even when you make the adjustments for the
general video.
Adjusts Red/Green/Blue/Yellow/Cyan, Magenta.
- Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is -30 - +30.
- Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -30 - +30.
- This feature is disable in RGB-PC and HDMI-PC mode.
*This feature is not available for all models.
■
As the technology to reduce the power consumption while keeping the same brightness, this has the effect of reducing power consumption, improvement in contrast.
Color Temperature
(Expert Control)
Color Management System
OPC
Color Standard
Standard: Displays standard set of colors.
Wide: Increase number of colors used.
■
Maximize the utilization of color to increase color quality.
Color Gamut
■
Show clearer and distinctive yet natural edges in of the video.
■
This function is enabled in "
PPiicc ttuurree MMoodd ee- CC iinnee mmaa, EE xx ppee rrtt
".
Edge Enhancer
■
This is the pattern necessary for expert adjustment.
■
This function is enabled in "
PPiicc ttuurree MMoodd ee- EE xx ppee rrtt
" when you watch DTV.
Expert Pattern
■
This is the function to filter the specific colors of the video.
You can use the RGB filter to set color saturation and hue accurately.
Color Filter
*This feature is not available for all models.
■
This is the function to express richer color.
■
This feature represents rich color as much as conventional video signal.
■
This function is enabled in "
PPiicc ttuurree mmoo ddee- CC iinnee mmaa, EE xx ppee rrtt
" when xvYCC sig-
nal is inputted through HDMI.
xvYCC
Page 84
PICTURE CONTROL
84
ENERGY SAVING
PICTURE CONTROL
It reduces the TV’s power consumption by lowering the backlight level.
The default factory setting complies with the
EEnneerr ggyy SStt aa rr
requirements and is adjusted to the comfortable
level to be viewed at home.
You can increase the brightness of your screen by adjusting the
EEnneerr ggyy SS aa vviinngg
level or by setting the
PPiicc ttuu rree
MMoo dd ee
.
■
When selecting
SSccrr eeee nn ooffff
, TV turned
off after 3 seconds.
■
If you adjust “
EE nn ee rr gg yy SS aavviinn gg --
MM ii nn ii mm uu mm, MM ee dd ii uu mm, MM aa xx ii mm uu mm
”,
BB aacckkll ii gghhtt
feature will not work.
■
You can also adjust
EE nnee rrggyy SSaavviinn gg
in
the
QQ..MMEE NNUU
.
■
Press the
EE NNEERRGG YY SSAAVVIINN GG
button
repeatedly to select the appropriate
Energy Saving setup.
Select
PPII CC TTUU RR EE
.
Select
EE nnee rrggyy SS aavvii nngg
.
1
MENU
2
ENTER
Select
OOffff, MMiinn ii mmuumm, MMee ddiiuu mm
,
MMaaxxiimm uu mm
, or
SSccrr ee ee nn OOffff
.
3
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
PICTURE
E
Enter
Move
PICTURE
E
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
Aspect Ratio : 16:9
Picture Wizard
Energy Saving
: Off
Picture Mode : Standard
• Backlight 70
• Contrast 90
• Brightness 50
• Sharpness 70
Off
Minimum
Medium
Maximum
Screen off
Page 85
PICTURE CONTROL
85
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Select
PPII CC TTUU RR EE
.
Select
PPiicc ttuurree RRee ss eett
.
1
MENU
2
ENTER
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Enter
Move
PICTURE
E
RG
• Contrast 50
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Resetting video configuration...
ii
No
Ye s
All picture settings will be resetted.
Continue?
?
Initialize the adjusted value.
4
Select
YY eess
.
3
ENTER
ENTER
5
MENU
Return to TV viewing.
Page 86
PICTURE CONTROL
86
POWER INDICATOR -
Except 19/22LD350
PICTURE CONTROL
Select
OOPP TTII OONN
.
Select
PPoo ww ee rr IInndd iiccaattoorr
.
1
MENU
2
ENTER
Select
SSttaa nndd bbyy LL iigghhttorPPoo ww ee rr LLii gghhtt
.
3
ENTER
Select your desired options.
4
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Power Indicator
Demo Mode : Off
Initial Setting : Home Use
Enter
Move
OPTION
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Power Indicator
Demo Mode : Off
Initial Setting : Home Use
Power Light
Standby Light
On
Close
FF
On
GG
EE
Adjust the power/standby indicator light of TV front.
■
SStt aannddbb yy LLiigghhtt
: Determines whether to
set the indicator light on the front of the
TV to
OO nn
or
OOffff
in standby mode.
■
PPoo ww ee rr LLii gghhtt
: Determines whether to set
the indicator light on the front of the TV
to
OO nn
or
OOffff
when the power turns on.
Page 87
PICTURE CONTROL
87
DEMO MODE
Select
OOPP TTII OONN
.
Select
DDeemmoo MMoodd ee
.
1
MENU
2
ENTER
Select
OO nn
to show the various
feature of the TV.
3
ENTER
4
MENU
Return to TV viewing.
After a while,
DDeemmoo MMoodd ee
starts.
If you want to stop the demo, press any button
(Except VOL +, - and MUTE button).
Enter
Move
OPTION
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Power Indicator
Demo Mode : Off
Initial Setting : Store Demo
Enter
Move
OPTION
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Power Indicator
Demo Mode : On
Initial Setting : Store Demo
EE
Off
On
Displays a slide show to explain the various feature of this TV.
■
This feature is disabled in “
IInn ii ttiiaa ll
SSee tttt iinngg-- HH oomm ee UU ssee
”.
Page 88
SOUND & LANGUAGE CONTROL
88
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER (AUTO VOLUME)
Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a
regular TV program.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed every
time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic
adjustments for each program.
Select
AAUUDD IIOO
.
Select
AAuuttoo VVoo lluummee
.
Select
OO nn
or
OOffff
.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Enter
Move
AUDIO
Auto Volume : On
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
E
LR
E
LR
Off
On
-+
-+
Page 89
SOUND & LANGUAGE CONTROL
89
CLEAR VOICE II
By differentiating the human sound range from others, it improves the sound quality of voices.
Select
AAUUDD IIOO
.
Select
CC llee aarr VVooiiccee II II
.
Select
OO nn
or
OOffff
.
1
MENU
3
2
ENTER
ENTER
6
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : On
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
E
LR
E
LR
Select
LL ee vv ee ll
.
4
ENTER
Make appropriate adjustments.
5
ENTER
Adjustment for Clear Voice Level
With selecting
OO nn
-+
-+
Off
On
Page 90
SOUND & LANGUAGE CONTROL
90
PRESET SOUND SETTINGS (SOUND MODE)
SOUND & LANGUAGE CONTROL
Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate
sound options based on the program content.
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
E
LR
E
LR
Select
AAUUDD IIOO
.
Select
SSoo uunndd MMoodd ee
.
Select
SSttaa nnddaa rrdd, MMuu ss iicc
,
CC iinnee mmaa, SSpp oorrtt
, or
GGaa mm ee
.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
■
SSttaa nnddaa rrdd, MMuu ss iicc, CC iinnee mmaa, SSpp oorrtt
,
and
GGaamm ee
are preset for optimum
sound quality at the factory.
■
You can also adjust
SSoo uunndd MMoo dd ee
in
the
QQ..MMEE NNUU
.
■
SS tt aa nndd aa rr dd
: Offers standard-quality
sound.
■
MMuu ss iicc
: Optimizes sound for listening to
music.
■
CC iinnee mmaa
: Optimizes sound for watching
movies.
■
SSpp oorrtt
: Optimizes sound for watching
sports events.
■
GGaa mm ee
: Optimizes sound for playing
games.
-+
-+
Standard
Music
Cinema
Sport
Game
Page 91
SOUND & LANGUAGE CONTROL
91
SOUND SETTING ADJUSTMENT - USER MODE
Adjust the sound to suit your taste and room situations.
INFINITE SOUND
Select
AAUUDD IIOO
.
Select
SSoo uunndd MMoodd ee
.
Select
TT rreebb ll ee
or
BB aassss
.
1
MENU
4
2
ENTER
Select
SSttaa nnddaa rrdd, MMuu ss iicc
,
CC iinnee mmaa, SSpp oorrtt
, or
GGaa mm ee
.
3
ENTER
ENTER
Enter
Move
AUDIO
LR
E
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Enter
Move
AUDIO
LR
E
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Select
AAUUDD IIOO
.
Select
IInn ffiinniittee SSoouunndd
.
Select
OO nn
or
OOffff
.
1
MENU
3
2
ENTER
ENTER
6
BACK
Return to the previous menu.
MENU
Return to TV viewing.
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Close
EE
EE
• Treble 50
• Bass 50
•
Infinite Sound
Off
Make appropriate adjustments.
5
ENTER
Select this option to sound realistic.
-+ -+
■
If sound quality or volume is not at the level
you want, it is recommended to use a separate
home theater system or amp to cope with different user environments.
■
If you select “
CC lleeaarr VV oo iiccee II II--OO nn
”,
IInnffiinn iittee
SSoo uu nndd
feature will not work.
Page 92
SOUND & LANGUAGE CONTROL
92
BALANCE
SOUND & LANGUAGE CONTROL
Select
AAUUDD IIOO
.
Select
BB aallaannccee
.
Make appropriate adjustments.
1
MENU
3
2
ENTER
ENTER
Adjust the left/right sound of speaker to suit your taste and room situations.
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
Enter
Move
AUDIO
Auto Volume : Off
Clear Voice II : Off
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
E
LR
E
LR
-+
-+
Close
EE
EE
Balance 0
LR
Page 93
SOUND & LANGUAGE CONTROL
93
TV SPEAKERS ON/OFF SETUP
Turn the TV speakers off if using external audio equipment.
In
AA VV, CCoo mm pp oo nneenntt, RR GG BB
and
HH DD MMII
with HDMI to DVI cable, the TV speaker can be operational even
when there is no video signal.
If you wish to use an external Hi-Fi system or a SRS System, turn off the TV’s internal speakers.
Select
AAUUDD IIOO
.
Select
TTVV SS ppeeaakkeerr
.
Select
OO nn
or
OOffff
.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
AUDIO
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
LR
E
Enter
Move
AUDIO
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
LR
E
Off
On
-+
-+
Page 94
SOUND & LANGUAGE CONTROL
94
AUDIO RESET
SOUND & LANGUAGE CONTROL
Settings of the selected Sound Mode return to the default factory settings.
Select
AAUUDD IIOO
.
Select
RR ee sseett
.
1
MENU
2
ENTER
Initialize the adjusted value.
3
ENTER
4
MENU
Return to TV viewing.
Enter
Move
AUDIO
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
LR
E
Enter
Move
AUDIO
• Level 3
Balance 0
Sound Mode : Standard
•
Infinite Sound :
Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
LR
E
Resetting audio configuration...
ii
-+
-+
Page 95
SOUND & LANGUAGE CONTROL
95
STEREO/SAP BROADCAST SETUP
For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used
if the broadcast is only in Mono.
Select
SS AAPP
.
Select
MMoo nn oo, SSttee rr ee oo
, or
SS AAPP
.
Return to TV viewing.
1
Q.MENU
3
2
Q.MENU
Select
MMuulltt ii AA uudd iioo
.
Select other languages.
Return to TV viewing.
1
Q.MENU
3
2
Q.MENU
Analog TV Digital TV
A
English
FF
Multi Audio
GG
Page 96
SOUND & LANGUAGE CONTROL
96
AUDIO LANGUAGE
SOUND & LANGUAGE CONTROL
Other languages may be available if a digital signal is provided by the broadcasting station.
This feature operates only in DTV/CADTV mode.
Select
OOPP TTII OONN
.
Select
AAuudd iioo LLaanngguuaaggee
.
Select your desired language.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
EE EE
English
Spanish
French
Page 97
SOUND & LANGUAGE CONTROL
97
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
Select
OOPP TTII OONN
.
Select
MMee nnuu LL aanngguuaa ggee
.
Select your desired language.
From this point on, the on-screen menus
will be shown in the selected language.
1
MENU
3
2
ENTER
ENTER
4
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
EE EE
English
Español
Français
Page 98
SOUND & LANGUAGE CONTROL
98
CAPTION MODE
SOUND & LANGUAGE CONTROL
Captions are provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen
and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both
digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode
which was last set when you turned the power off. This function is only available when
CCaa pp ttii oo nn
Mode is set
OO nn
.
Select
OOPP TTII OONN
.
Select
CC aapp ttiioonn
.
Select
OO nn
.
1
MENU
3
2
ENTER
ENTER
Select
CC CC 11-44
or
TTee xxtt11-44
.
4
Analog Broadcasting System Captions
■
When selecting
OOff ff
, Sub-menus for
Analog, DTV, and Digital Option become
disabled.
■
CC AAPPTT IIOONN
The term for the words that scroll
across the bottom of the TV screen;
usually the audio portion of the program provided for the hearing impaired.
■
TT EE XX TT
The term for the words that appear in a
large black frame and almost cover the
entire screen; usually messages provided by the broadcaster.
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : CC1
Set ID : 1
Mode
CC1
Close
Digital Option
FF
On
GG
EE EE
Page 99
SOUND & LANGUAGE CONTROL
99
Digital Broadcasting System Captions
Choose the language you want the DTV/CADTV Captions to appear in.
Other Languages can be chosen for digital sources only if they are included on the program.
This function in only available when Caption Mode is set On.
Select
OOPP TTII OONN
.
Select
CC aapp ttiioonn
.
Select
OO nn
.
1
MENU
3
2
ENTER
ENTER
Select
CC CC 11-44, TTee xxtt11-44
, or
SSee rrvviicc ee 11- 66
.
4
5
BACK
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : CC1
Set ID : 1
EE EE
Mode
CC1
Close
Digital Option
FF
On
GG
Page 100
SOUND & LANGUAGE CONTROL
100
SOUND & LANGUAGE CONTROL
Caption Option
Customize the DTV/CADTV captions that appear on your screen.
This function in only available when Caption Mode is set On.
Select
OOPP TTII OONN
.
Select
CC aapp ttiioonn
.
Select
OO nn
.
1
MENU
3
2
ENTER
ENTER
Select
CC uussttoo mm
.
5
ENTER
Customize the
SSiizz ee, FFoo nn tt
, etc., to your
preference. A preview icon is provided at
the bottom of the screen, use it to see the
caption language.
6
Select
DDiigg iitt aall OO ppttiioonn
.
4
Size
A Standard
Font
Font 1
Text Color
White
Text Opacity
Solid
Edge Type
None
Edge Color
Black
Bg Color
Black
Bg Opacity
Solid
Close
FF
Custom
GG
■
SSiizz ee
: Set the word size.
■
FFoo nn tt
: Select a typeface for the text.
■
TTee xxtt CC ooll oorr
: Choose a color for the
text.
■
TTee xx tt OOppaacciitt yy
: Specify the opacity
for the text color.
■
BB gg ((BBaa cckkgg rroo uunndd )) CCoo lloo rr
: Select a
background color.
■
BB gg ((BBaa cckkgg rroo uunndd )) OO pp aacciitt yy
: Select
the opacity for the background color.
■
EE dd gg ee TTyypp ee
: Select an edge type.
■
EE dd gg ee CCoo lloo rr
: Select a color for the
edges.
7
RETURN
Return to the previous menu.
MENU
Return to TV viewing.
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : Off
Set ID : 1
Enter
Move
OPTION
Menu Language : English
Audio Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Simple Manual
Caption : CC1
Set ID : 1
EE EE
Mode
CC1
Close
Digital Option
On
Loading...