Lexycom TIAMIS-800 Installation Manual

TIAMIS-800 wireless radio transceiver

Installation Manual

Lexycom Technologies, Inc.

1227 Reserve Dr.

Longmont, CO 80501

[e-mail]

March 2006, Ver. 1.0

TIAMIS-800 wireless radio transceiver
Installation Manual. Ver. 1.0

Table of Contents

Table of Contents .............................................................................................................2

Revision history.................................................................................................................. 3

Notice.................................................................................................................................. 3

General Safety Information................................................................................................. 4

Electro Static Discharge (ESD) .......................................................................................... 4

FCC Notification................................................................................................................. 5

Electronic FCC ID .............................................................................................................. 6

1. Transceiver Installation................................................................................................... 8

Step 1. Install the Transceiver......................................................................................... 8

Step 2. Install the Antenna.............................................................................................. 8

Step 3. Install the Antenna Feedline............................................................................... 8

Step 4. Install the Power for the Transceiver.................................................................. 8

Step 5. Connect Computer to the Transceiver................................................................ 9

2. Transceiver Configuration............................................................................................ 11

Step 1. Determine the Signal Loss in your Antenna Cable........................................... 11

Step 2. Determine the Maximum Allowed Transceiver’s Output Power Settings....... 13

Step 3. Adjust Transceiver’s Output Power.................................................................. 15

Information in this document is subject to change without notice.
© 2006 Lexycom Technologies, Inc. All rights reserved.
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
Other product names mentioned in this manual may be copyrights, trademarks, or registered
trademarks of their respective companies and are hereby acknowledged.

The Tiamis-800 Wireless Data Transceiver is made in the United States of America.
Printed in the United States of America.

TIAMIS-800 wireless radio transceiver
Installation Manual. Ver. 1.0

Revision history

Revision Released Firmware level covered

1.0 March, 2006 1106.i and prior, PCB Rev A2

Notice

Changes or modifications not expressly approved by Lexycom Technologies, Inc. could
void the user’s authority to operate this equipment.

Any and all product information in this document is subject to change without notice.

TIAMIS-800 wireless radio transceiver
Installation Manual. Ver. 1.0

General Safety Information

Lexycom Technologies, Inc. does not recommend the use of its products in life support
applications where the failure or malfunction of a component may directly threaten life or
lead to an injury.

Do not operate radio equipment near electrical blasting caps or in an explosive
atmosphere.

Do not operate radio transmitter unless all RF connectors are secure and any open
connectors are properly terminated.

Do not allow the antenna to come close to, or touch, the eyes, face, or any exposed body
parts while the radio is transmitting.

Be sure that your Tiamis-800 transceiver has been provided with sufficient DC voltage
and current.

All equipment should be installed according to the manufacturer’s instructions and in
accordance with all regulatory agencies.

Electro Static Discharge (ESD)

Static build up can cause serious damage to electronic devices when improperly handled.
Appropriate precautions should be taken when handling the transceiver(s).

TIAMIS-800 wireless radio transceiver
Installation Manual. Ver. 1.0

FCC Notification

This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: 1) This device may not cause harmful interference and 2) this device
must accept any interference received, including interference that may cause undesired
operation.

This device must be operated as supplied by Lexycom Technologies, Inc. Any changes or
modifications made to the device without the express written approval of Lexycom
Technologies may void the user's authority to operate the device.

WARNING: The Tiamis-800 transceiver has the maximum transmitted output power of

1 Watt. It is required that the transmit antenna be kept at least 23 cm away
from nearby persons to satisfy FCC RF exposure requirements.

NOTE: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in the commercial installations. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.