Lexmark OPTRA COLOR 1200, 1200, OPTRA 1200 User Manual

Overview of Printer Menus

SUPPLIES MENU

<color> Toner <color> PC Drum Tray 1 Status

Tray 2 Status Tray

3 Status

TESTS MENU

Print Menus Print Fonts Print Directory Print Demo Color Samples Factory Defaults Format Flash

Format Disk Job Acct Stat

Hex Trace

MAINTENANCE MENU

Maint Status

JOB MENU

Cancel Job Reset Printer Print Buffer

COLOR MENU

Color Correction Print Quality Toner Saver

SETUP MENU

Printer Language Power Saver Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Print Area Display Language Alarm Control Printer Usage Timing Adj

Job Buffer Size Job Accounting Job Acct Limit

PAPER MENU

Paper Source PAPER SIZE PAPER TYPE CUSTOM TYPES Output Bin Substitute Size Configure MP Size Detection

PCL EMUL MENU

Font Source Font Name Point Size Pitch Symbol Set Orientation Lines per Page A4 Width TRAY RENUMBER Auto CR after LF Auto LF after CR

FINISHING MENU

Copies Blank Pages Collation Separator Sheets Separator Source Multipage Print Multipage Order Multipage View Multipage Border

POSTSCRIPT MENU

Print PS Error Font Priority Image Smoothing

PARALLEL MENU

STD PARALLEL

PARALLEL OPT 1 PARALLEL OPT 2

PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer

Job Buffering

Advanced Status Protocol Honor Init Parallel Mode 1 Parallel Mode 2

Operator Panel

Select

Return

Stop

Press <Menu> to:

• Enter the menus from the ready state

• Scroll through menus or values

• Increase or decrease a numerical value

• Display the Job Menu or the Supplies Menu while the printer is busy

Press Select to:

• Select the item on the second line of the display

• Save the selection as a new default setting

SERIAL MENU

SERIAL OPTION 1 SERIAL OPTION 2

PCL SmartSwitch PS SmartSwitch NPA Mode Serial Buffer Job Buffering RS-232/RS-422 RS-422 Polarity Serial Protocol Robust XON Baud Data Bits Parity Honor DSR

NETWORK MENU

NETWORK OPTION 1 NETWORK OPTION 2

PCL SmartSwitch PS SmartSwitch NPA Mode Network Buffer Job Buffering NETWORK x SETUP

INFRARED MENU

Infrared Port PCL SmartSwitch PS SmartSwitch NPA Mode Infrared Buffer Job Buffering Window Size Transmit Delay Max Baud Rate

LOCALTALK MENU

LocalTalk Port PCL SmartSwitch PS SmartSwitch NPA Mode LocalTalk Buffer Job Buffering NPA Hosts LocalTalk Name LocalTalk Addr LocalTalk Zone

FAX MENU

Fax Port Fax Baud Fax Data Bits Fax Parity Fax Buffer

Note: Menu items in italics appear on the display only if a required option is installed.

Capitalized menu items (for example, PAPER SIZE) have submenus.

Press Return to:

• Back up to the previous menu level

Press Stop to:

• Temporarily stop all print activity without losing data

Press Go to:

• Exit printer menus and return to the ready state

• Clear messages

Quick Reference

Lexmark Optra Color 1200

Loading Transparencies

Important!

P/N 12A0540 (letter) or P/N 12A0541 (A4).

Use only Lexmark transparencies,

Clearing Paper Jams

Open the top cover all the way and remove the print units.

Gently remove jammed paper from inside the printer.

Loading Paper

Important!

the paper size.

Load paper face down. Make sure the paper fits under the corner tabs.

Adjust width guides.

Move the

A4, A5, B5, and Letter

Maximum stack height

Long edge

B4, A3, Legal, and 11x17

rear guide

Corner tab

to the proper position for

Rear guide

Tray 1

Cardboard sheet with cutout

Multipurpose Feeder

Transparencies

Notch

Check for jammed paper in the paper tray and paper tray opening.

Press the large green tab on each print unit and reinstall the print units.

Short edge

Maximum stack height

Corner tab

Rear guide

Notch

This document is printed on recycled paper. 3/98

E.C. 1C0105 P/N 11F0847

Close the top and rear covers and press Go.