Lexmark 0528RFU OEM Integration Instructions
OEM module Integration Instructions
Integration into PN:
40C0745 or 40C0747
The Lexmark UHF RFID Module is designed for OEM Installation only into Lexmark compatible tray options only. The module
transmits in the frequency range of 902 - 928 MHz and is designed to function in the RF Exposure Category General
Population/Uncontrolled Environment. Thus the installer should ensure that exposure by personnel while testing and operation of
this module should maintain a distance of 20CM from the antenna.
This device complies with part 15 of the FCC Rules and Industry Canada license – exempt RSS Standards. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
A minimum separation distance of 20 CM must be maintained between the antenna and the person for this appliance to satisfy the
RF exposure requirements.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could
void the User’s authority to operate the equipment.
The module and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter.
OEM Module Assembly and integration instructions follow:
Name: 550 Tray ASM RFID
Rev. Date: 21 Sept 2016 Pg 1
Lxk contact: Ward Inabinet (859-227-
4670)
ASSEMBLY INSTRUCTIONS
PN: 40C0745 or
40C0747
ID
A 40C2100-Option ASM 1
B
C
D
E
F
Tool /
Fixture ID
F1
T1 Box cutter
PN &
Description
Description
Qty
Rev. Date: 15 Sept 2016 Pg 2
Name: 550 Tray ASM RFID
1. Receive packaged Option. Open Box.
2. Remove foam packing sides and bag. Store for later reuse. Option on flat, clean
surface.
A
Lxk contact: Ward Inabinet (859-227-
4670)
ASSEMBLY INSTRUCTIONS
PN: 40C0745 or
40C0747
ID
A 3087791 or 3087808 1
B
C
D
E
F
Tool /
Fixture ID
F1
T1
PN &
Description
Description
Qty
Rev. Date: 15 Sept 2016 Pg 3
Name: 550 Tray ASM RFID (NA or EU)
1. CS72x Option and RFID Module (A) shown.
2. Open Option Tray and remove corrugated insert. Discard insert.
Lxk contact: Ward Inabinet (859-227-
4670)
A
ASSEMBLY INSTRUCTIONS
PN: 40C0745 or
40C0747
ID
A Metal screw 2
B Plastite Screw 1
C
D
E
F
Tool /
Fixture ID
F1
T1 Power Driver
PN &
Description
Description
Qty
Rev. Date: 15 Sept 2016 Pg 4
Name: 550 Tray ASM RFID (NA or EU)
1. Remove Tray completely from Option. Place Tray aside.
2. Unfasten screws and
remove Right Cover.
Stor e cover and screws
for later re-assembly.
Lxk contact: Ward Inabinet (859-227-
4670)
PN: 40C0745 or
40C0747
ID
A
B
C
D
E
F
Tool /
Fixture ID
F1
T1
Description
PN &
Description
ASSEMBLY INSTRUCTIONS
Name: 550 Tray ASM RFID (NA or EU)
Qty
1. Note Option PCBA and cables on right side.
2. Carefully disconnect indicated cable. Note: significant force is required.
Rev. Date: 15 Sept 2016 Pg 5
Lxk contact: Ward Inabinet (859-227-
4670)
Loading...