LEXIBOOK DJ010NO User Manual

DJ010series
Digital Camera
User Guide
Mode d’emploi
DJ010series IM.indd 1 13/02/2007 18:41:35
DJ010series IM.indd 2 13/02/2007 18:41:35
A
B
C
1
2
3
4
5 6
7
8
9
DJ010series IM.indd 3 13/02/2007 18:41:35
4
PRESENTATION DE VOTRE APPAREIL PHOTO
Veuillez vous référer aux images A & B illustrées au dos de la page de couverture.
1. Couvercle de la prise USB 2. Afchage LCD 3. Bouton de suppression
4. Bouton HI/LO/ 5. Attache de courroie 6. Bouton d’obturateur
7. Viseur 8. Emplacement pour trépied 9. Compartiment des piles
MISE EN PLACE DES PILES NEUVES Veuillez vous référer à l’image C illustrée à l’arrière de la page de couverture.
1. Assurez-vous que l’appareil photo soit éteint.
2. Ouvrez le compartiment des piles en faisant glisser le couvercle.
3. Respectez la polarité des piles (symboles +/-) à l’intérieur du compartiment.
4. Insérez 2 piles neuves de type AAA. Replacez et fermez le couvercle en le faisant glisser en position. Avertissement: Si l’unité dysfonctionne ou reçoit un choc électrique, enlevez les piles et insérez-les de nouveau. Remarque importante: Tous les chiers s’effacent lorsque les piles sont remplacées. Assurez-vous de transférer les chiers sur votre
PC avant cette manipulation.
INSTALLER LE PILOTE ET LE LOGICIEL DE L’APPAREIL PHOTO
Suivez ces instructions pour installer le pilote et le logiciel d’application de l’appareil photo sur votre PC.
1. Insérez le CD du logiciel (inclus) dans le lecteur de CD-ROM. Le CD s’initialisera automatiquement et le menu d’installation suivant apparaîtra:
Cliquez sur “Install driver”, puis suivez les instructions pour installer le pilote. Vous devrez redémarrer votre ordinateur après l’installation du pilote.
DJ010series IM.indd 4 13/02/2007 18:41:36
5
Remarque: Si le CD ne démarre pas automatiquement, cliquez sur Démarrer Exécuter, écrivez “D:\setup.exe” dans la boîte de dialogue d’exécution (où D:\ est votre lecteur CD-ROM).
2. Procédez de la même manière pour installer le logiciel PhotoImpression et Fun­house. Le logiciel PhotoImpression et Funhouse offre de nombreuses applications pour éditer et imprimer vos photos.
Remarques: - Vous devez installer le pilote avant de transférer des photos à partir de l’appareil photo.
- Vous devez cliquer sur “Browse CD” – “User guide” pour lire le guide d’utilisation concernant le logiciel PhotoImpression et Funhouse. Si vous ne pouvez pas lire les chiers, vous devrez tout d’abord installer Acrobat Reader.
MISE EN MARCHE ET ARRET DE L’APPAREIL PHOTO
Appuyez sur le bouton d’obturateur [6] durant 5 secondes pour mettre l’appareil photo en marche. Remarque: L’appareil photo s’éteindra automatiquement après 60 secondes d’inactivité.
SELECTION DE LA RESOLUTION DES PHOTOS
Il y a 2 modes de résolution : Haute résolution : photos de 1280*960 pixels. L’appareil photo peut stocker environ 25 photos. Basse résolution : photos de 640*480 pixels. L’appareil photo peut stocker environ 100 photos. Appuyez sur le bouton HI/LO/ [4] pour sélectionner HI (haute) ou LO (basse) résolution qui s’afchera dans le coin supérieur gauche de l’écran LCD.
PRISE DE PHOTOS
Appuyez sur l’obturateur [6] pour prendre une photo. Vous entendrez un “bip” sonore après chaque prise de photo. Le nombre de photos encore disponible en mémoire s’afche sur l’écran LCD.
DJ010series IM.indd 5 13/02/2007 18:41:37
6
SUPPRESSION DE FICHIERS
Supprimer la dernière photo prise
Appuyez sur le bouton [3] pour sélectionner l’icône inférieure de la poubelle afchée sur l’écran LCD. Appuyez sur le bouton d’obturateur [6] dans les 5 secondes qui suivent pour supprimer la dernière photo prise.
Supprimer tous les chiers
Appuyez deux fois sur le bouton [3] pour sélectionner l’icône supérieure de la poubelle afchée sur l’écran LCD. Appuyez sur le bouton d’obturateur [6] dans les 5 secondes qui suivent pour supprimer toutes les photos stockées dans l’appareil photo. Remarque: Si vous appuyez sur le bouton par erreur, attendez simplement
5 secondes pour annuler cette opération.
Prise de photos continue
Ce mode vous permet de prendre une succession de photos rapides que l’appareil photo sauvegardera sous la forme d’un court clip vidéo en format AVI. Appuyez et maintenez le bouton HI/LO/ [4] pour sélectionner l’icône sur l’écran LCD. Gardez le bouton d’obturateur [6] appuyé pour prendre plusieurs photos de manière continue et automatiquement.
TELECHARGEMENT DE VOS PHOTOS
1. Connectez l’appareil photo à votre ordinateur avec le câble USB fourni. Vous entendrez un petit bip sonore et l’écran LCD s’allumera lorsque l’appareil photo sera
connecté au PC.
2. Ouvrez le logiciel PhotoImpression. Sur le côté gauche de la fenêtre ouverte, cliquez sur “Get photo”.
3. Dans la partie inférieure de l’écran, cliquez sur “Camera/scanner”, puis dans “Sélectionnez la source”, sélectionnez “Dual Camera”. Pour terminer, cliquez sur “acquérir” (icône scan/appareil photo).
4. Vos photos seront afchées au bas de l’écran. Remarque: Pour plus d’informations sur PhotoImpression, veuillez vous référer au guide d’utilisation inclus dans le CD du logiciel.
DJ010series IM.indd 6 13/02/2007 18:41:37
7
MODE PC CAM
Connecté à votre PC, votre appareil photo peut être utilisé comme webcam. Dans « Poste de travail », cliquez deux fois sur un nouveau pilote appelé “Dual Camera”. Vous serez alors en mode webcam.
Conférence vidéo
1. Réglez votre appareil photo numérique sur le mode PC Cam.
2. Installez le logiciel de conférence vidéo Microsoft NetMeeting sur votre ordinateur.
3. Entrez l’adresse IP de l’ordinateur que vous désirez contacter dans la barre d’adresse.
4. Sélectionnez les options tool/accept/transfer. Lorsque le correspondant accepte votre appel, vous pourrez alors tenir une conférence vidéo.
Chat MSN
1. Assurez-vous que votre appareil photo numérique soit éteint.
2. Appuyez et maintenez le bouton d’alimentation/obturateur [7]. Branchez le câble
USB au port USB de votre PC.
3. Connectez-vous à MSN.
4. Connectez l’appareil photo numérique à votre ordinateur en utilisant le câble
USB.
5. Sur l’interface MSN, sélectionnez Action/Start pour démarrer une conversation MSN.
6. Sélectionnez la personne avec qui vous désirez communiquer et appuyez sur OK.
COQUES INTERCHANGEABLES
Votre appareil photo offre 2 coques interchangeables. Pour enlever et insérer une coque, utilisez un outil pointu pour détacher chaque coin de l’appareil photo. Enclen­chez la nouvelle coque.
DJ010series IM.indd 7 13/02/2007 18:41:37
GARANTIE
Ce produit est couvert par notre garantie de deux ans. Pour toute mise en œuvre de la garantie ou de service après-vente, vous devez vous adresser à votre revendeur muni de votre preuve d’achat. Notre garantie couvre les vices de matériel ou de montage imputables au constructeur à l’exclusion de toute détérioration provenant du non-respect de la notice d’utilisation ou de toute intervention intempestive sur l’article (telle que démontage, exposition à la chaleur ou à l’humidité…). Note : Veuillez garder ce mode d’emploi, il contient d’importantes informations. Le contenu de ce mode d’emploi peut changer sans préavis. Aucune partie de ce mode d’emploi ne doit être reproduite sans le consentement écrit du fabricant. LEXIBOOK S.A, 2, avenue de Scandinavie, 91953 Courtaboeuf Cedex France Assistance technique : 0892 23 27 26 (0,34 € TTC/Min), www.lexibook.com
Informations sur la protection de l’environnement
Tout appareil électrique usé est une matière recyclable et ne devrait pas faire partie des ordures ménagères! Nous vous demandons de bien vouloir nous soutenir en contribuant activement au ménagement des ressources et à la protection de l’environnement en déposant cet appareil dans sites de collecte (si existants).
8
Please refer to images A & B located at the back of the cover page.
1. USB socket cover 2. LCD display 3. delete button 4. HI/LO/ button
5. Strap mount 6. Shutter button 7. Viewnder 8. Brace hole 9. Battery
compartment
Please refer to image C located at the back of the cover page.
1. Make sure the camera is off.
2. Open the battery compartment by sliding the cover off.
3. Note the polarity of the batteries (+/- signs) inside of the battery compartment.
4. Insert 2 new AAA batteries. Replace and close the battery cover by sliding it into
place.
Warning: If the unit malfunctions or receives an electrostatic shock, remove the battery and insert it again. Important note: all les will be lost when replacing the batteries. Make sure you transfer the les to your PC before changing the batteries.
Follow these instructions to install the camera driver and application software on your PC system.
1. Insert the CD Software (included) in your CD-ROM drive. The CD will auto run, and the following installation menu will appear:
Click on “Install driver”, and then follow the instructions to install it. You will need to reboot your computer after the driver installation.
DJ010series IM.indd 8 13/02/2007 18:41:38
ENGLISH
9
GETTING TO KNOW YOUR CAMERA
Please refer to images A & B located at the back of the cover page.
1. USB socket cover 2. LCD display 3. delete button 4. HI/LO/ button
5. Strap mount 6. Shutter button 7. Viewnder 8. Brace hole 9. Battery
compartment
INSERTING NEW BATTERIES
Please refer to image C located at the back of the cover page.
1. Make sure the camera is off.
2. Open the battery compartment by sliding the cover off.
3. Note the polarity of the batteries (+/- signs) inside of the battery compartment.
4. Insert 2 new AAA batteries. Replace and close the battery cover by sliding it into
place.
Warning: If the unit malfunctions or receives an electrostatic shock, remove the battery and insert it again. Important note: all les will be lost when replacing the batteries. Make sure you transfer the les to your PC before changing the batteries.
INSTALLING THE CAMERA DRIVER AND SOFTWARE
Follow these instructions to install the camera driver and application software on your PC system.
1. Insert the CD Software (included) in your CD-ROM drive. The CD will auto run, and the following installation menu will appear:
Click on “Install driver”, and then follow the instructions to install it. You will need to reboot your computer after the driver installation.
DJ010series IM.indd 9 13/02/2007 18:41:38
Note: If the CD does not auto run, click Start Run, type in “D:\setup.exe” in the Run dialog text box (where D:\ is your CD-ROM drive).
2. Proceed similarly to install the PhotoImpression and Funhouse software. Photo­Impression and Funhouse software offer many applications for photo editing and printing. Notes: - You must install the driver before downloading pictures from the camera.
- You can click on “Browse CD” – “User guide” to read the user guides of the Pho­toImpression and Funhouse software. If you cannot read the les, you will have to install Acrobat Reader rst.
TURNING THE CAMERA ON AND OFF
Press the Shutter button [6] for 5 seconds to turn the camera ON. Note: The camera will auto power off after 60 seconds of inactivity.
SELECTING THE PHOTO RESOLUTION
There are 2 resolution modes: High resolution: pictures of 1280*960 pixels. The camera can store about 25 pictures in this mode. Low resolution: pictures of 640*480 pixels. The camera can store about 100 pictures in this mode. Press the HI/LO/ button [4] to select HI (high) or LO (low) resolution on the upper left corner of the LCD screen.
TAKING PHOTOS
Press the Shutter button [6] to take a photo. You will hear a ‘beep’ sound after each photo taken. The number of pictures you can still take in memory in shown on the LCD screen.
DELETING FILES
Deleting the last picture taken
Press the button [3] to select the lower trash can icon
ENGLISH
10
DJ010series IM.indd 10 13/02/2007 18:41:38
ENGLISH
11
as shown on the LCD screen. Press the Shutter button [6] within 5 seconds to delete the last picture taken.
Deleting all les
Press the button [3] twice to select the upper trash can icon as shown on the LCD screen. Press the Shutter button [6] within 5 seconds to delete all the pictures stored in the camera. Note: if you press the button by mistake, just wait 5 seconds to cancel this
operation.
Continuous Picture Shots
This mode allows you to take a succession of quick shots which the camera will save as short video clips in AVI format. Press and hold the HI/LO/ button [4] to select the icon on the LCD screen. Keep the Shutter button [6] pressed to take several photos continuously and auto­matically.
DOWNLOADING YOUR PHOTOS
1. Connect the camera to your computer via the USB cable provided. You will hear a small beep sound and the LCD screen will turn on when the camera is connected to your PC.
2. Open the PhotoImpression software. On the left side of the opening screen, click on “Get photo”.
3. On the bottom part of the screen, click on “Camera/scanner”, then in “Select source” select “Dual Camera”. Finally, click on “acquire” (scan/camera icon).
4. Your photos will be displayed on the bottom part of the screen. Note: for more information on PhotoImpression, please refer to the user guide included in the software CD.
PC CAM MODE
Connected to your PC, your camera can be used as a webcam. In “My Computer”, double click on a new drive called “Dual Camera”. You will be in webcam mode.
Video Conference
1. Set your digital video camera to PC Cam mode.
2. Run the video conference software Microsoft NetMeeting on your computer.
DJ010series IM.indd 11 13/02/2007 18:41:39
ENGLISH
12
3. Input the IP address of the computer you wish to dial in the address bar.
4. Select tool/accept/transfer options. When the other parties have accepted your call, you can now hold a video conference.
MSN Chat
1. Make sure the digital video camera is OFF.
2. Press and hold the Power/Shutter button [7]. Plug the USB jack into the USB port of your PC.
3. Sign in MSN.
4. Connect the digital video camera to your computer using the USB cable.
5. On the MSN interface, select Action/Start a video conversation.
6. Select the person you want to chat with, and press OK.
INTERCHANGEABLE COVERS
Your digital camera comes with 2 interchangeable covers. To remove and insert a cover, use a sharp instrument to unsnap the cover on each corner of the camera.
Snap in a new cover.
WARRANTY
NOTE: Please keep this instruction manual, it contains important information. This
product is covered by our two-year warranty. To make use of the warranty or the after-sales service, please contact your retailer and supply proof of purchase. Our warranty covers material or installation-related defects attributable to the manufacturer, with the exception of wear caused by failure to respect the instructions for use or any unauthorised work on the equipment (such as dismantling, exposure to heat or damp, etc.). LEXIBOOK UK ltd, Unit 10 Peterseld Industrial Estate, Bedford Road, Peterseld, Hampshire, GU32 3QA, United Kingdom, Freephone helpline: 0808 100 3015, http://www.lexibook.com
Environmental Protection
Unwanted electrical appliances can be recycled and should not be discarded along with regular household waste! Please actively support the conservation of resources and help protect the environment by returning this appliance to a collection centre (if available).
DJ010series IM.indd 12 13/02/2007 18:41:39
Loading...
+ 25 hidden pages