Leviton RZCZ1 User Manual

DI-000-RZCZ4-00A-X1

/./&&

/./&&

/./&&

/./&&

/./&&

/./&&

/./&&/./&&

/./&&

/./&&

/./&&

/./&&

Compatible with enabled products!

TM

1 ON

2 ON

3 ON

4 ON

OFF

OFF

OFF

OFF

Hot (Black)

Neutral (White)

Line

120VAC, 60Hz

BKWH

Green
Ground

4-Zone Controlller

2

3

1

WARNINGS AND CAUTIONS:

• ON/OFF LED for remote load control.

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualified electrician.

• Vizia™ RF RZCZ4 remote does not control the load, but provides scene applications to operate with Vizia

• Recommended minimum wall box depth is 2-1/2".

TM

RF switches.

4-Zone Controller

Cat. No. RZCZ4

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:

• Can call up four (4) zone ON/OFF with advanced Programmer/Remote (see RZCPG).

• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

INTRODUCTION

Leviton’s ViziaTM RF components are designed to communicate with
each other via Radio Frequency (RF) to provide remote control of your
lighting. Using RF technology allows Leviton to provide the greatest
signal integrity possible. Each module in Leviton’s Vizia
line is a Z-Wave

TM

enabled device. In a Z-WaveTM network, each device
is designed to act as a router. These routers will re-transmit the RF signal
from one device to another until the intended device is reached. This
ensures that the signal is received by its intended device by routing the
signal around obstacles and radio dead spots. The 4-Zone Controller
is compatible with any Z-Wave™ enabled network, regardless of the
manufacturer and can also be used with other devices displaying the
Z-Wave™ logo.

FEATURES

• This is a Z-Wave™ Controller

• Zone/Area control without traveler wires

• Can control ON/OFF dim/bright for up to 4 Zones/Area.

• ON/OFF LED

• Two way communication

• RF reliability

• Ease of installation – No new wiring

• Compatible with other Z-Wave™ enabled devices

Tools needed to install your 4-Zone Controller:

Slotted/Phillips Screwdriver Electrical Tape Pliers
Pencil Cutters Ruler

Changing the color of your 4-Zone Controller:

Your 4-Zone controller includes three color options. The controller ships
with the White frame attached. To change color of frame, proceed as
follows:

Push in
side at tab
to release

After frame is removed, remove existing push buttons by pressing out
buttons from back of frame and replace them with desired color change
push buttons by pressing in from front of frame. To make IR capable, use
new DIM/BRIGHT button with IR window.

Line up tabs
and press in
side to attach

TM

RF component

INSTALLING YOUR 4-ZONE CONTROLLER

NOTE: Use check boxes when Steps are completed.

Step 1

Step 2

Step 3

Side Wire Connection

Side wire terminals accept
#14 AWG

• Make sure that the ends of the wires from the wall box are

WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is off

before wiring!

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble this

configuration, consult a qualified electrician.

1. Line (Hot)

2. Neutral

3. Ground

Preparing and connecting wires:

This 4-Zone controller can be wired using side wire terminal
screws or through backwire openings. Choose appropriate wire
stripping specifications accordingly.

5/8"

(if necessary)

Cut

solid wire copper only.

straight (cut if necessary).

(1.6 cm)

Back Wire (either hole may be used)

Back wire openings use #14-12 AWG
solid wire copper only.

Strip Gage
(measure bare
wire here)

Step 4

Wiring Application:

WIRING SWITCH:
Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "BK".

• Line Neutral wall box wire to terminal screw marked "WH".

Step 5

• Restore power at circuit breaker or fuse.

• LED should turn ON, when any button is pressed. If LED does not turn

Step 6

NOTES:

• If using a non-Leviton Programmer/Remote, refer to the Programmer/

• 4-Zone controllers incuded into a Z-Wave

A) If using a Leviton Z-WaveTM Programmer/Remote, Cat. No. RZCPG,

Testing your 4-Zone Controller prior to mounting
in wall box:

• Position all wires to provide room in
outlet wall box for device.

• Ensure that the word “TOP” is facing up
on device strap.

• Partially screw in mounting screws in
wall box mounting holes.

NOTE: Dress wires with a bend as

shown in diagram in order to relieve
stress when mounting device.

ON, refer to the TROUBLESHOOTING section.

Including 4-Zone Controller into Z-WaveTM
Network:

Remote instruction sheet.

after you have included all other devices.

press the Menu button and scroll down to System Setup. Press the
center button to select System Setup Menu. Press the center button to
select Network. Press the center button to <Include Node>.

TM

network must be updated

Step 6 cont'd

B) If using RZCPG Programmer/Remote, you will be prompted to place

4-Zone controller into programming mode.

C) To access Program mode, press and hold the

left side of buttons 1 and 3
Wait 5 seconds until the LED turns Amber.
Release the button and the LED will blink
Amber. You are now in Programming mode.

NOTE: If the LED on the 4-Zone controller

turns solid Red while including, there has
been a communication error.

D) While standing close to the 4-Zone controller

(approximately 2-5 ft.), press the center button
on the Programmer/Remote to <Include>
device in the network.
may be included at any time.

E) The Primary Programmer/Remote will assign

a Home ID, Node ID, and Name for this
device.

NOTE: This information will be stored in the Programmer/Remote to

be used for future reference.

NOTE: You may name or edit the node of this device at this time.

F) The 4-Zone controller is now installed in the network.
G) After all devices are included into the network, the controller must

be updated to allow proper network function. To update controller
proceed as follows:

• If using a non-Leviton Programmer/Remote, refer to the
Programmer/Remote instruction sheet for updating controller.

• If using Leviton Z-Wave
press the Menu button and scroll down to System Setup. Press
the center button to select System Setup Menu. Press the center
button to select Network. Press the center button to select Update
"cntrl". When prompted, press desired button on 4-Zone controller.

• Wait until the RZCPG Programmer/Remote confirms completion.
Update is done.

NOTE: If the 4-Zone controller has been
successfully Included in the network and
the user tries to Include it again without first
excluding it from the network, the controller
will retain the first node ID it had received and
ignore the second.

(refer to figure).

NOTE: Only one device

TM

Programmer/Remote, Cat. No. RZCPG,

Center
Button

Programmer/Remote

Cat. No. RZCPG

Menu
Button

Step 6 cont'd

Including 4-Zone Controller into
Z-WaveTM Network:

Programmer/Remote

Cat. No. RZCPG

NOTE: Programmer/Remote must be

in close proximity to 4-Zone controller
when including in the network.

Step 8

After inclusion process, you must associate the devices to
the controllers. Refer to the Primary Programmer/Remote
instruction sheet for complete details.

NOTE: One (1) Z-WaveTM device can be associated to multiple controllers

(up to five (5) controllers maximum).
NOTE: If using a non-Leviton Programmer/Remote, refer to the

Programmer/Remote instruction sheet for associating a device.

Step 9

Device Association:

4-Zone Controller Mounting:

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

TROUBLESHOOTING

• Locator LED on controller does not turn ON

- Circuit breaker or fuse has tripped.

- If 4-Zone controller is powered up and LED does not turn ON, check
wiring.

• Zone Controller does not operate lights

- Check association.

- Ensure that controller was properly updated.

•

If LED turns solid red

- Check association.

- Ensure that each device in the network is with in 70 ft (21 m) of another
device.

NOTES

Step 7

Excluding 4-Zone Controller from
Z-WaveTM Network:

A) If using a Leviton Z-WaveTM Programmer/Remote, Cat. No. RZCPG,

press the Menu button and scroll down to System Setup. Press the
center button to select System Setup Menu. Press the center button
to select Network. Scroll down to <Exclude Node> and press the
center button.

B) If using RZCPG Programmer/Remote, you will be prompted to place

4-Zone controller into programming mode.

C) To access Program mode, press and hold the left side of buttons 1

NOTE: If the LED on the 4-Zone controller turns solid Red while

D) While standing close to the 4-Zone controller (approximately 2-5 ft.),

(refer to figure). Wait 5 seconds until the LED turns Amber.

and 3
Release the buttons and the LED will blink Amber. You are now in
Programming mode.

excluding, there has been a communication error.

press the center button on the Programmer/Remote to <Exclude>
device in the network.

Factory Default:

If your 4-Zone controller is not responding, or you are unable to control
it after you have tried to Include/Exclude it multiple times, it may be
necessary to reset the 4-Zone controller to its original factory settings. To
accomplish this, proceed as follows:

• On the 4-Zone controller
and hold the left side of buttons 1 and 3. Wait
approximately 5 seconds until the locator LED
turns Amber and then turns solid Red. Release
the buttons. The 4-Zone controller is now reset.
Once the controller is reset, it will be necessary to
Re-Include it to a network before it can be used.

(refer to figure), press

CAUTION: SETTING A DEVICE TO A FACTORY

DEFAULT DOES NOT EXCLUDE THAT DEVICE
FROM A NETWORK. THE EXCLUSION
PROCEDURE MUST STILL BE FOLLOWED TO
REMOVE THE DEVICE FROM THE PRIMARY
CONTROLLER’S INFORMATION TABLE. FAILURE
TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND,
OR MAY FAIL TO RESPOND TO SOME DEVICES.

Installation may now be completed by
tightening mounting screws into wall box.
Attach wallplate.

Step 10

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

OPERATION

Push Button (Default settings)
Turn ON from OFF position:

Press left side of button – Turns all lights in
Zone/Area ON, LED turns ON.
LED will blink until Zone/Area is ON.

Turn OFF from ON position:

Press right side of button – Turns all lights in
Zone/Area OFF, LED turns OFF.

Dim/Bright:

Press left side of Dim/Bright button - Lights in
last activated Zone/Area will dim.

Press right side of Dim/Bright button - Lights in
last activated Zone/Area will brighten.

NOTE: Controller will only Dim/Bright devices
located within the Radio Frequency range.

NOTE: LED will be lit Green if any one load in
the associated Area is ON. LED will be OFF
when all loads are turned OFF.

If there is a power outage, when the power is
restored, the lights will return to the last setting
before the power interruption.

Cleaning: Clean with a damp cloth. DO NOT
use chemical cleaners.

Locator

LED

Push

Buttons

Dim/Bright

Button

For additional information, contact Leviton’s

Techline at 1-800-824-3005 or visit Leviton’s

website at www.ViziaRF.com

U.S. & Foreign Patents Pending

Copyright© 2006 Leviton Manufacturing Co., Inc.

All Rights Including Trade Dress Rights Reserved

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a
Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

• Consult the dealer or an experienced radio/tv technician for help.

DI-000-RZCZ4-00A-X1

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,
at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability

for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions.

implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

There are no other or