Leviton LB1GC User Manual

Page 1
WiFi Module – Installation Manual
FCC ID of this product is as follows:
FCC ID: QGH-LB1GC
IC ID of this product is as follows:
IC: 2473A-LB1GC
For OEM integration only – device cannot be sold to general public.
Therefore we will include the following statements required by FCC and Industry Canada (IC) on the product and in the Installation Manual Notice.
Contents:
Supply Voltage
1.
2.
Theory of operation
3.
Module Dimensions
4.
Module Footprint
5.
Antenna Notice
6.
1 Leviton Confidential
Page 2
1. Supply Voltage
Operating Temperature Range -40 +25 +85 Deg. C
Operating Voltage 2.7 3.3 3.5 V
Min. Typ. Max. Unit
2 Leviton Confidential
Page 3
2. Theory of Operation – WiFi Channels
Channel # Frequency
Dec Hex
1 1 2401 2412 2423 17 2 2 2406 2417 2428 17 3 3 2411 2422 2433 17 4 4 2416 2427 2438 17 5 5 2421 2432 2443 17 6 6 2426 2437 2448 17 7 7 2431 2442 2453 17 8 8 2436 2447 2458 17
9 9 2441 2452 2463 17 10 A 2446 2457 2468 17 11 B 2451 2462 2473 14
Lower
MHz
Center
MHz
Upper
MHz
TX Power -
MAX dB/ channel
(Dec)
Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the
digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
Frequency Tolerance: ± 20ppm
3 Leviton Confidential
Page 4
3. Module Dimensions
Place the module along the PCB edge.
4 Leviton Confidential
Page 5
4. Module Footprint
Recommended Module land Pattern
Place the module along the PCB edge.
5 Leviton Confidential
Page 6
5. Antenna
Please refer to KDB 996369
Please perform the antenna design that followed the specifications of the antenna.
About the signal line between an antenna and a module
It is a 50-ohm line design.
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check "Class1 change" and "Class2 change" which the authorities define then.
The concrete contents of a check are the following three points.
It is the same type as the antenna type of antenna specifications.
1.
An antenna gain is lower than a gain given in antenna specifications.
2.
The emission level is not getting worse.
3.
6 Leviton Confidential
Page 7
5. Antenna
Conducted emissions testing:
Option for
Conducted Testing
U.FL.
EFR32MGxx
R2
R1
RF2
RF1
RF3
CHIP
Antenna
7 Leviton Confidential
Page 8
6. Notice
For OEM integration only – device cannot be sold to general public.
Therefore we will include the following statements required by FCC/IC on the product
and in the Installation Manual Notice.
Please describe the following warning on the final product which contains this module.
Contains Transmitter Module: FCC ID:QGH-LB1GC
IC: 2473A-LB1GC
Please describe the following warning to the manual.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
OR
Contains: FCC ID: QGH-LB1GC
IC: 2473A-LB1GC
8 Leviton Confidential
Page 9
6. Notice
This device is intended only for OEM integrators under the following conditions:
1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2)The transmitter module may not be co-located with any other transmitter or antenna.
3)The use of an antenna with gain less than 1.2 dBi (2.4GHz).
As long as the 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:QGH-LB1GC”. “Contains IC: 2473A-LB1GC”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
9 Leviton Confidential
Loading...