Page 1
Single Pole
120VAC, 60Hz
Fan Speed Control
Cat. No. INF05-1L, 5A (Lighted)
INSTALLATION INSTRUCTIONS
FEATURES
• Leviton's Decora® style design • Color conversion available
• Minimum Speed Adjustment • ON/OFF LED indicates status of load
INSTALLATION INSTRUCTIONS
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND
REGULATIONS.
WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED
ELECTRICIAN.
WARNING: TO AVOID OVERHEATING AND POSSIBLE DAMAGE TO THIS DEVICE AND OTHER EQUIPMENT, DO
NOT INSTALL TO CONTROL A RECEPTACLE, FLUORESCENT LIGHTING, A MOTOR- OR A TRANSFORMEROPERATED APPLIANCE OTHER THAN APPROPRIATE CEILING FANS.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, THIS CONTROL IS TO BE USED WITH
CEILING FANS THAT ARE MARKED AS SUITABLE FOR USE WITH A SOLID-STATE FAN SPEED CONTROL AND IS
RATED 120 VOLTS AC, TOTAL LOAD 5 AMPERES MAXIMUM.
WARNING: FOR USE ON CEILING PADDLE FANS WITH SPLIT-CAPACITOR OR SHADED POLE MOTORS ONLY.
PLEASE REFER TO FAN MANUFACTURER’S INSTRUCTIONS OR RATING LABEL ON THE MOTOR TO CONFIRM
TYPE. USE WITH ANY OTHER TYPES OF MOTORS OR EQUIPMENT MAY CAUSE OVERHEATING AND/OR DAMAGE
TO THE MOTORS OR EQUIPMENT.
OTHER CAUTIONS:
1. DISCONNECT POWER WHEN SERVICING FIXTURE.
2. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY DEVICES
MARKED CO/ALR OR CU/AL.
MULTI-GANG INSTALLATION:
When ganging dimmers, the side sections of the mounting strap
must be removed. Use pliers to carefully bend side sections
back and forth until they break off (see Figure 1). The side
sections dissipate heat, so removing them requires a derating of
the control’s capacity (see chart).
TO INSTALL:
1.
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN
OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST
THAT POWER IS OFF BEFORE WIRING!
2. Remove existing wallplate and switch or dimmer, if
applicable.
3. Remove 3/4¨ (1.9 cm) of insulation from each circuit
conductor. Make sure the ends of wires are straight.
4. Connect wires per WIRING DIAGRAM as follows: Twist
strands of each separate lead tightly and, with circuit
conductors push firmly into appropriate wire connector.
Screw connectors on clockwise making sure no bare wires
show below the wire connectors. Secure each connector with
electrical tape.
NOTE: This model incorporates a trim adjustment which will
allow the installer to precisely set the minimum end of the
speed control range to suit each installation. This adjustment
is preset at the factory and should require no further
adjustments for most installations. If adjustment is required
proceed as follows, otherwise continue with step 8:
5. Restore power at circuit breaker or fuse. Raise and lower (full bottom stroke) the slider several times (see Figure 1).
The GREEN LED will turn ON and OFF indicating power to the switch. Set the slider to the ON position (GREEN LED
OFF). Position the slider to the minimum speed level (bottom of stroke, before it clicks OFF).
6. The trim adjustment is located at the top of the Fan Speed Control back cover (see Figure 1). Using a small, insulated
screwdriver, rotate the trim adjustment clockwise to increase fan speed; counter-clockwise to lower the fan speed until
the desired minimum speed level is obtained.
7. Check for proper operation by raising the slider to it’s maximum position (top of stroke-fan speed high) and returning to
minimum (bottom of stroke-fan speed low). If operation is not satisfactory, repeat step 6. When the speed is adjusted to
satisfaction, TURN OFF POWER.
8. Installation may now be completed by carefully positioning all wires to provide room in outlet box for Fan Speed
Control. Mount control into box with mounting screws supplied. Attach Decora
®
wallplate.
9. Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE.
DI-000-INF05-00A
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for
the benefit of anyone else that this product at the time of its sale
by Leviton is free of defects in materials and workmanship under
normal and proper use for two years from the purchase date.
Leviton’s only obligation is to correct such defects by repair or
replacement, at its option, if within such two year period the
product is returned prepaid, with proof of purchase date, and a
description of the problem to Leviton Manufacturing Co., Inc.,
Att: Quality Assurance Department, 59-25 Little Neck
Parkway, Little Neck, New York 11362-2591 (In Canada send
to Leviton Mfg. of Canada Ltd., 165 Hymus Blvd., Point Claire,
(Quebec), Canada H9R 1E9). This warranty excludes and there
is disclaimed liability for labor for removal of this product or
reinstallation. This warranty is void if this product is installed
improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under
normal operating conditions or not in accordance with any labels
or instructions. There are no other or implied warranties of any
kind, including merchantability and fitness for a particular
purpose, but if any implied warranty is required by the applicable
jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to
two years. Leviton is not liable for incidental, indirect, special, or
consequential damages, including without limitation, damage to,
or loss of use of, any equipment, lost sales or profits or delay or
failure to perform this warranty obligation. The remedies provided
herein are the exclusive remedies under this warranty, whether
based on contract, tort or otherwise.
For Technical Assistance Call:
1-800-824-3005 (U.S.A. Only)
1 800 405-5320 (Canada Only)
www.leviton.com
R
DI-000-INF05-00A
/
R
C O L L E C T I O N B Y L E V I T O N
Two More than
Cat. No. Single Gang 2 Gang
INF05-1L 600W, 5A 500W, 4.1A 400W, 3.3A
MAXIMUM LOAD PER CONTROL FOR MULTI-GANG
/
Figure 1 - Fan Speed Control Functions
Slider
ON/OFF
LED
Trim Adjustment
Screw
Mounting Strap
Side Sections
Page 2
Hot (Black)
Neutral (White)
Fan
Fan Speed Control
Black
Green
Ground
Black
White
Red
Line
120VAC, 60Hz
Wiring Diagram - Single Location Control Application
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your
interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your Leviton
distributor and proceed as follows (please note that
wallplate must be removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using your fingers,
grip around the Decora
®
frame and push on one side to
release it from the strap (see Figure 2).
3. Take the new frame and position it properly to the
strap. Line up the plastic snaps with the square holes
in the strap. Insert the snaps on one side of the frame
into the strap.
4. Firmly press sideways and down to slip the other snaps
into place. The frame snaps in with a audible click.
Ensure that all four snaps are secure.
5. Moving the slider up or down will automatically engage
the slider control mechanism. Replace Decora
®
wallplate. The color conversion is complete.
TO OPERATE
• GREEN LED will remain ON when the fan is OFF
- Facilitates access to switch in the dark.
• Raise slider from full bottom stroke to ON position
- Fan will turn ON (GREEN LED will turn OFF) at
level set by slider.
• Move slider control lever up or down
- Fan will increase or decrease in speed
respectively for desired level.
• Lower slider to full bottom stroke to OFF position
- fan will turn OFF (GREEN LED will turn ON).
TROUBLESHOOTING
• Fan does not turn ON and ON/OFF LED does not
turn ON
- Circuit breaker or fuse has tripped.
- Fan has burned out.
- Fan is not connected to line Neutral.
Figure 2 - Color Conversion
Frame
Strap
Snaps
Push in 2 Locations
ON/OFF
LED
Slider
Loading...